1.

4 Name of each part Cautions:

➀ ESC key: Cancels the last key operation or returns to the previous screen. 1) If a keyword to prohibit read, write or read and write of programs is registered in the PLC, only the
➄ ➁ "-" key: Scrolls the device No. to a smaller one or decrements a numeric clock time display function is available. Any other function shown above is not available.
value by. If any operation is performed in the 5DM when a keyword is registered in the PLC, the error display
➂ "+" key: Scrolls the device No. to a larger one or increments a numeric flickers for 5 seconds.
value. 2) The automatic backlight OFF function is set to 10 minutes as the initial value. As far as the OFF time
➃ OK key: Determines the display device, executes write of a numeric value, is not changed by a sequence program, the backlight turns off 10 minutes later.
or changes over forced setting and forced resetting.
➅ If any key is pressed after the backlight turns off, the contents displayed just before the backlight turns
➀ ➁ ➂ ➃
➄ Display area: Displays the current time and the monitored device status. off appear again. A key pressed for the first time after the backlight turns off is regarded as a trigger to
➆ ➅ Connector for PLC turn on the backlight, and is not regarded as a key operation.
➆ 5DM mounting hook
4.2 Control devices for 5DM
2. Installation When using the 5DM control function, specify data registers (D) and auxiliary relays (M) used to control
DISPLAY MODULE FX1N-5DM the 5DM to special data registers D8158 and D8159.
Install the 5DM to the PLC using the following procedure. Five data registers and 15 auxiliary relays are occupied for control of the 5DM.
USER’S MANUAL A) Top cover for DM (offered as an accessory of 5DM)
B) Connector for optional equipment
For the control device use procedure, refer to the FX1S/FX1N/FX2N/FX2NC Series Programming Manual.
C) M3 screw to fix top cover Special D Control device Description Application
JY992D84901G
• Remove the top cover of the basic unit, and attach the top cover for DM D{ Device type to be displayed *1 For specified device
A) instead. D{+1 Device No. to be displayed monitor function
Plug the 5DM in to the connector B). D8158 For automatic backlight
D{+2 Backlight OFF time (min)
This manual only describes the specifications for Display Module FX1N-5DM. • If the 5DM is always used, the top cover can be fixed with the M3 screw K{ OFF function
For complete operation, wiring, mounting and programming instructions please refer to the FX1S, FX1N C). (Tightening torque: 0.3 to 0.6 Nxm) D{+3 Protects display screen. *2 For protect function
HARDWARE MANUAL and PROGRAMMING MANUAL.
If the 5DM is used together with a function expansion board, remove and D{+4 Not available.
These manuals should be read and understood before attempting to install or use the unit.
attach the 5DM by pressing the 5DM mounting hook provided at the bottom M… Requests edition of displayed device data. For specified device
of the 5DM.
M…+1 Edition completion response monitor function

3. Specifications Disables backlight OFF function. For automatic backlight

M…+2
(Turns on backlight forcedly.) OFF function
Related Manuals M…+3 Displays or hides operation errors, etc. *3 Others
3.1 Environmental specifications
Manual name Manual No. Description The environmental specifications are equivalent to those of the PLC main unit. (Refer to the handy manual M…+4 ESC key status *4
offered with the FX1S/FX1N Series PLC main unit.) M…+5 "-" key status *4 For specified device
Describes contents related to hardware of FX1S Series
FX1S Series Hardware M…+6 "+" key status *4 monitor function
JY992D83901 PLC such as specifications, wiring and installation. 3.2 Power supply specifications D8159
Manual
(It is offered with FX1S Series PLC basic unit.) The power is supplied from the PLC main unit. K… M…+7 OK key status *4
Describes contents related to hardware of FX1N Series 5V DC, 110 mA M…+8 Not available.
FX1N Series Hardware
JY992D88201 PLC such as specifications, wiring and installation. M…+9 Not available.
Manual
(It is offered with FX1N Series PLC basic unit.) 4. Outline of Performance M…+10 Not available.
FX Series M…+11 Not available.
JY992D88101 Describes instructions in FX1S/FX1N/FX2N/FX2NC Series. This section describes the function list of the 5DM.
Programming Manual II
The operator functions available with the operation keys of the 5DM are described on the back of this manual. M…+12 Not available.
For the 5DM control functions available from the PLC, refer to the FX1S/FX1N/FX2N/FX2NC Series Program- M…+13 Not available.
ming Manual.
1. Outline of Product M…+14 Not available.
4.1 Function list
*1 Input numeric values correspond to the devices as follows.
1.1 Features Symbols stand for the following. 1: Input (X) 2: Output (Y) 3: Auxiliary relay (M) 4: State (S) 5: Timer (T)
X: Input Y: Output M: Auxiliary relay S: State T: Timer C: Counter D: Data register 6: Counter (C), 16-bit (current value/set value) and 32-bit (set value)
The micro display module FX1N-5DM (hereafter referred to as "5DM") is
BFM: Butter memory of special units and special blocks 7: Data register (D), 16-bit8: Data register (D), 32-bit 9: Time display
mounted on the top face of the FX1S/FX1N Series PLC basic unit and
can monitor/update internal PLC data. Operator functions: The operator can use these functions by using only the operation keys of the 5DM. 10: Counter (C), 16-bit (current value/set value) and 32-bit (current value)
Refer to the simplified chart of operations shown on the back face of this manual. *2 0: Enables all operations. 1: Enables only the time display function.
Function Description 2: Enables only the monitor function.
PLCs installed to: FX1S and FX1N Series
Clock function *3 PC hardware errors, parameter errors, grammatical errors and circuit errors are unconditionally displayed.
Display Displays current time of clock function (built in FX1S/FX1N Series). While this bit is ON, I/O configuration errors, parallel link errors and operation errors are also displayed.
Setting Allows to set time (year, month, day, hour and minute). *4 Every operation key is the momentary type, and functions as follows:
1.2 Product configuration Device monitor function While a key is pressed and held: ON
Bit device monitor Displays ON/OFF status of X, Y, M and S. While key is not pressed: OFF
Main unit : FX1N-5DM Word device (16-bit) monitor Displays current and set values of T and C and current value of D.
Accessories : Top cover for DM 1, M3 screw to mount top cover 1 4.3 Description on display area
Word device (32-bit) monitor Displays current and set values of 32-bit C and current value of D.
1.3 Outside dimensions Displays buffer memory of special units and special blocks The display area of the 5DM shows the following.
Buffer memory monitor function
When installed to a PLC (offered only in FX1N Series).
➀ ➁ ➂ ➃➄ ➀ "RUN": Displayed while the PLC is running, and not displayed while
2 40 Displays error code and error occurrence step No. when a PLC the PLC is stopped.
(0.07) (1.57) Error display function
error has occurred.
9 26 RUN BFM ON R D
➁ "BFM": Displays the contents of the buffer memory when a special
(0.35) (1.03) Forced set/reset function Forces ON and OFF bit devices Y, M and S. ➅ TCD
Note: These dimensions XYMS
- ➇ block is connected (only in the FX1N Series).
T/C reset function Clears current value of T and C (current value: 0, contact: OFF).
(0.86)

(1.1)
22

28

measured
from the left side
Data change function ➆ ➈ ➂ "ON/OFF": Displayed while T or C is ON in the word device monitor
are common Current value change Change current value of T, C and D. function, and not displayed while T or C is OFF.
(0.55)
2.6(0.1)

FX1S Series
(1.25)
14

➃ "R" (reset): Displayed while T or C is reset.

32

to the FX1S and Set value change Change set value of T and C.
FX1N Series.
5DM control functions: The 5DM is controlled by sequence programs.
4.6 FX1N Series ➄ "D" (32-bit): Displayed when a 32-bit D is specified.
(0.18) For use of these functions, refer to the FX Series Programming Manual ΙΙ
(0.29)

10 8 8 8
7.5

➅ Device type: Displays the device type (T, C, D, X, Y, M or S) currently

(0.39) (0.31) (0.31) (0.31)
(1.41)
36

Function Description
being displayed.
Enables full use of all operator functions, enables only monitor
Protect function
function or enables only clock time display function. ➆ Device No.: Displays the device No. currently being displayed.
Unit: mm (inches) Allows to specify device type and device No. to be displayed in
Outer painting color: Munsell 0.08GY/7.64/0.81 Specified device monitor function
5DM. ➇ Current value: Displays the current value of T, C or D.
Mass: 20 g (0.05 lbs) Error display enable/disable
Enables or disables error display function (operator function). ➈ Set value: Displays the set value of T or C.
function
Automatic backlight OFF function Allows to set automatic backlight OFF time (initial value: 10 min). * In the case of 32-bit C or D, upper 5 digits are displayed in ➇ and the
Operation key status recognition lower 5 digits are displayed in ➈.
Recognizes ON/OFF status of four operation keys.
function
 1.4 Name of each part Cautions:

➀ ESC key: Cancels the last key operation or returns to the previous screen. 1) If a keyword to prohibit read, write or read and write of programs is registered in the PLC, only the
➄ ➁ "-" key: Scrolls the device No. to a smaller one or decrements a numeric clock time display function is available. Any other function shown above is not available.
value by. If any operation is performed in the 5DM when a keyword is registered in the PLC, the error display
➂ "+" key: Scrolls the device No. to a larger one or increments a numeric flickers for 5 seconds.
value. 2) The automatic backlight OFF function is set to 10 minutes as the initial value. As far as the OFF time
➃ OK key: Determines the display device, executes write of a numeric value, is not changed by a sequence program, the backlight turns off 10 minutes later.
or changes over forced setting and forced resetting.
➅ If any key is pressed after the backlight turns off, the contents displayed just before the backlight turns
➀ ➁ ➂ ➃
➄ Display area: Displays the current time and the monitored device status. off appear again. A key pressed for the first time after the backlight turns off is regarded as a trigger to
➆ ➅ Connector for PLC turn on the backlight, and is not regarded as a key operation.
➆ 5DM mounting hook
4.2 Control devices for 5DM
2. Installation When using the 5DM control function, specify data registers (D) and auxiliary relays (M) used to control
DISPLAY MODULE FX1N-5DM the 5DM to special data registers D8158 and D8159.
Install the 5DM to the PLC using the following procedure. Five data registers and 15 auxiliary relays are occupied for control of the 5DM.
USER’S MANUAL A) Top cover for DM (offered as an accessory of 5DM)
B) Connector for optional equipment
For the control device use procedure, refer to the FX1S/FX1N/FX2N/FX2NC Series Programming Manual.
C) M3 screw to fix top cover Special D Control device Description Application
JY992D84901G
• Remove the top cover of the basic unit, and attach the top cover for DM D{ Device type to be displayed *1 For specified device
A) instead. D{+1 Device No. to be displayed monitor function
Plug the 5DM in to the connector B). D8158 For automatic backlight
D{+2 Backlight OFF time (min)
This manual only describes the specifications for Display Module FX1N-5DM. • If the 5DM is always used, the top cover can be fixed with the M3 screw K{ OFF function
For complete operation, wiring, mounting and programming instructions please refer to the FX1S, FX1N C). (Tightening torque: 0.3 to 0.6 Nxm) D{+3 Protects display screen. *2 For protect function
HARDWARE MANUAL and PROGRAMMING MANUAL.
If the 5DM is used together with a function expansion board, remove and D{+4 Not available.
These manuals should be read and understood before attempting to install or use the unit.
attach the 5DM by pressing the 5DM mounting hook provided at the bottom M… Requests edition of displayed device data. For specified device
of the 5DM.
M…+1 Edition completion response monitor function

3. Specifications Disables backlight OFF function. For automatic backlight

M…+2
(Turns on backlight forcedly.) OFF function
Related Manuals M…+3 Displays or hides operation errors, etc. *3 Others
3.1 Environmental specifications
Manual name Manual No. Description The environmental specifications are equivalent to those of the PLC main unit. (Refer to the handy manual M…+4 ESC key status *4
offered with the FX1S/FX1N Series PLC main unit.) M…+5 "-" key status *4 For specified device
Describes contents related to hardware of FX1S Series
FX1S Series Hardware M…+6 "+" key status *4 monitor function
JY992D83901 PLC such as specifications, wiring and installation. 3.2 Power supply specifications D8159
Manual
(It is offered with FX1S Series PLC basic unit.) The power is supplied from the PLC main unit. K… M…+7 OK key status *4
Describes contents related to hardware of FX1N Series 5V DC, 110 mA M…+8 Not available.
FX1N Series Hardware
JY992D88201 PLC such as specifications, wiring and installation. M…+9 Not available.
Manual
(It is offered with FX1N Series PLC basic unit.) 4. Outline of Performance M…+10 Not available.
FX Series M…+11 Not available.
JY992D88101 Describes instructions in FX1S/FX1N/FX2N/FX2NC Series. This section describes the function list of the 5DM.
Programming Manual II
The operator functions available with the operation keys of the 5DM are described on the back of this manual. M…+12 Not available.
For the 5DM control functions available from the PLC, refer to the FX1S/FX1N/FX2N/FX2NC Series Program- M…+13 Not available.
ming Manual.
1. Outline of Product M…+14 Not available.
4.1 Function list
*1 Input numeric values correspond to the devices as follows.
1.1 Features Symbols stand for the following. 1: Input (X) 2: Output (Y) 3: Auxiliary relay (M) 4: State (S) 5: Timer (T)
X: Input Y: Output M: Auxiliary relay S: State T: Timer C: Counter D: Data register 6: Counter (C), 16-bit (current value/set value) and 32-bit (set value)
The micro display module FX1N-5DM (hereafter referred to as "5DM") is
BFM: Butter memory of special units and special blocks 7: Data register (D), 16-bit8: Data register (D), 32-bit 9: Time display
mounted on the top face of the FX1S/FX1N Series PLC basic unit and
can monitor/update internal PLC data. Operator functions: The operator can use these functions by using only the operation keys of the 5DM. 10: Counter (C), 16-bit (current value/set value) and 32-bit (current value)
Refer to the simplified chart of operations shown on the back face of this manual. *2 0: Enables all operations. 1: Enables only the time display function.
Function Description 2: Enables only the monitor function.
PLCs installed to: FX1S and FX1N Series
Clock function *3 PC hardware errors, parameter errors, grammatical errors and circuit errors are unconditionally displayed.
Display Displays current time of clock function (built in FX1S/FX1N Series). While this bit is ON, I/O configuration errors, parallel link errors and operation errors are also displayed.
Setting Allows to set time (year, month, day, hour and minute). *4 Every operation key is the momentary type, and functions as follows:
1.2 Product configuration Device monitor function While a key is pressed and held: ON
Bit device monitor Displays ON/OFF status of X, Y, M and S. While key is not pressed: OFF
Main unit : FX1N-5DM Word device (16-bit) monitor Displays current and set values of T and C and current value of D.
Accessories : Top cover for DM 1, M3 screw to mount top cover 1 4.3 Description on display area
Word device (32-bit) monitor Displays current and set values of 32-bit C and current value of D.
1.3 Outside dimensions Displays buffer memory of special units and special blocks The display area of the 5DM shows the following.
Buffer memory monitor function
When installed to a PLC (offered only in FX1N Series).
➀ ➁ ➂ ➃➄ ➀ "RUN": Displayed while the PLC is running, and not displayed while
2 40 Displays error code and error occurrence step No. when a PLC the PLC is stopped.
(0.07) (1.57) Error display function
error has occurred.
9 26 RUN BFM ON R D
➁ "BFM": Displays the contents of the buffer memory when a special
(0.35) (1.03) Forced set/reset function Forces ON and OFF bit devices Y, M and S. ➅ TCD
Note: These dimensions XYMS
- ➇ block is connected (only in the FX1N Series).
T/C reset function Clears current value of T and C (current value: 0, contact: OFF).
(0.86)

(1.1)
22

28

measured
from the left side
Data change function ➆ ➈ ➂ "ON/OFF": Displayed while T or C is ON in the word device monitor
are common Current value change Change current value of T, C and D. function, and not displayed while T or C is OFF.
(0.55)
2.6(0.1)

FX1S Series
(1.25)
14

➃ "R" (reset): Displayed while T or C is reset.

32

to the FX1S and Set value change Change set value of T and C.
FX1N Series.
5DM control functions: The 5DM is controlled by sequence programs.
4.6 FX1N Series ➄ "D" (32-bit): Displayed when a 32-bit D is specified.
(0.18) For use of these functions, refer to the FX Series Programming Manual ΙΙ
(0.29)

10 8 8 8
7.5

➅ Device type: Displays the device type (T, C, D, X, Y, M or S) currently

(0.39) (0.31) (0.31) (0.31)
(1.41)
36

Function Description
being displayed.
Enables full use of all operator functions, enables only monitor
Protect function
function or enables only clock time display function. ➆ Device No.: Displays the device No. currently being displayed.
Unit: mm (inches) Allows to specify device type and device No. to be displayed in
Outer painting color: Munsell 0.08GY/7.64/0.81 Specified device monitor function
5DM. ➇ Current value: Displays the current value of T, C or D.
Mass: 20 g (0.05 lbs) Error display enable/disable
Enables or disables error display function (operator function). ➈ Set value: Displays the set value of T or C.
function
Automatic backlight OFF function Allows to set automatic backlight OFF time (initial value: 10 min). * In the case of 32-bit C or D, upper 5 digits are displayed in ➇ and the
Operation key status recognition lower 5 digits are displayed in ➈.
Recognizes ON/OFF status of four operation keys.
function
 1.4 Name of each part Cautions:

➀ ESC key: Cancels the last key operation or returns to the previous screen. 1) If a keyword to prohibit read, write or read and write of programs is registered in the PLC, only the
➄ ➁ "-" key: Scrolls the device No. to a smaller one or decrements a numeric clock time display function is available. Any other function shown above is not available.
value by. If any operation is performed in the 5DM when a keyword is registered in the PLC, the error display
➂ "+" key: Scrolls the device No. to a larger one or increments a numeric flickers for 5 seconds.
value. 2) The automatic backlight OFF function is set to 10 minutes as the initial value. As far as the OFF time
➃ OK key: Determines the display device, executes write of a numeric value, is not changed by a sequence program, the backlight turns off 10 minutes later.
or changes over forced setting and forced resetting.
➅ If any key is pressed after the backlight turns off, the contents displayed just before the backlight turns
➀ ➁ ➂ ➃
➄ Display area: Displays the current time and the monitored device status. off appear again. A key pressed for the first time after the backlight turns off is regarded as a trigger to
➆ ➅ Connector for PLC turn on the backlight, and is not regarded as a key operation.
➆ 5DM mounting hook
4.2 Control devices for 5DM
2. Installation When using the 5DM control function, specify data registers (D) and auxiliary relays (M) used to control
DISPLAY MODULE FX1N-5DM the 5DM to special data registers D8158 and D8159.
Install the 5DM to the PLC using the following procedure. Five data registers and 15 auxiliary relays are occupied for control of the 5DM.
USER’S MANUAL A) Top cover for DM (offered as an accessory of 5DM)
B) Connector for optional equipment
For the control device use procedure, refer to the FX1S/FX1N/FX2N/FX2NC Series Programming Manual.
C) M3 screw to fix top cover Special D Control device Description Application
JY992D84901G
• Remove the top cover of the basic unit, and attach the top cover for DM D{ Device type to be displayed *1 For specified device
A) instead. D{+1 Device No. to be displayed monitor function
Plug the 5DM in to the connector B). D8158 For automatic backlight
D{+2 Backlight OFF time (min)
This manual only describes the specifications for Display Module FX1N-5DM. • If the 5DM is always used, the top cover can be fixed with the M3 screw K{ OFF function
For complete operation, wiring, mounting and programming instructions please refer to the FX1S, FX1N C). (Tightening torque: 0.3 to 0.6 Nxm) D{+3 Protects display screen. *2 For protect function
HARDWARE MANUAL and PROGRAMMING MANUAL.
If the 5DM is used together with a function expansion board, remove and D{+4 Not available.
These manuals should be read and understood before attempting to install or use the unit.
attach the 5DM by pressing the 5DM mounting hook provided at the bottom M… Requests edition of displayed device data. For specified device
of the 5DM.
M…+1 Edition completion response monitor function

3. Specifications Disables backlight OFF function. For automatic backlight

M…+2
(Turns on backlight forcedly.) OFF function
Related Manuals M…+3 Displays or hides operation errors, etc. *3 Others
3.1 Environmental specifications
Manual name Manual No. Description The environmental specifications are equivalent to those of the PLC main unit. (Refer to the handy manual M…+4 ESC key status *4
offered with the FX1S/FX1N Series PLC main unit.) M…+5 "-" key status *4 For specified device
Describes contents related to hardware of FX1S Series
FX1S Series Hardware M…+6 "+" key status *4 monitor function
JY992D83901 PLC such as specifications, wiring and installation. 3.2 Power supply specifications D8159
Manual
(It is offered with FX1S Series PLC basic unit.) The power is supplied from the PLC main unit. K… M…+7 OK key status *4
Describes contents related to hardware of FX1N Series 5V DC, 110 mA M…+8 Not available.
FX1N Series Hardware
JY992D88201 PLC such as specifications, wiring and installation. M…+9 Not available.
Manual
(It is offered with FX1N Series PLC basic unit.) 4. Outline of Performance M…+10 Not available.
FX Series M…+11 Not available.
JY992D88101 Describes instructions in FX1S/FX1N/FX2N/FX2NC Series. This section describes the function list of the 5DM.
Programming Manual II
The operator functions available with the operation keys of the 5DM are described on the back of this manual. M…+12 Not available.
For the 5DM control functions available from the PLC, refer to the FX1S/FX1N/FX2N/FX2NC Series Program- M…+13 Not available.
ming Manual.
1. Outline of Product M…+14 Not available.
4.1 Function list
*1 Input numeric values correspond to the devices as follows.
1.1 Features Symbols stand for the following. 1: Input (X) 2: Output (Y) 3: Auxiliary relay (M) 4: State (S) 5: Timer (T)
X: Input Y: Output M: Auxiliary relay S: State T: Timer C: Counter D: Data register 6: Counter (C), 16-bit (current value/set value) and 32-bit (set value)
The micro display module FX1N-5DM (hereafter referred to as "5DM") is
BFM: Butter memory of special units and special blocks 7: Data register (D), 16-bit8: Data register (D), 32-bit 9: Time display
mounted on the top face of the FX1S/FX1N Series PLC basic unit and
can monitor/update internal PLC data. Operator functions: The operator can use these functions by using only the operation keys of the 5DM. 10: Counter (C), 16-bit (current value/set value) and 32-bit (current value)
Refer to the simplified chart of operations shown on the back face of this manual. *2 0: Enables all operations. 1: Enables only the time display function.
Function Description 2: Enables only the monitor function.
PLCs installed to: FX1S and FX1N Series
Clock function *3 PC hardware errors, parameter errors, grammatical errors and circuit errors are unconditionally displayed.
Display Displays current time of clock function (built in FX1S/FX1N Series). While this bit is ON, I/O configuration errors, parallel link errors and operation errors are also displayed.
Setting Allows to set time (year, month, day, hour and minute). *4 Every operation key is the momentary type, and functions as follows:
1.2 Product configuration Device monitor function While a key is pressed and held: ON
Bit device monitor Displays ON/OFF status of X, Y, M and S. While key is not pressed: OFF
Main unit : FX1N-5DM Word device (16-bit) monitor Displays current and set values of T and C and current value of D.
Accessories : Top cover for DM 1, M3 screw to mount top cover 1 4.3 Description on display area
Word device (32-bit) monitor Displays current and set values of 32-bit C and current value of D.
1.3 Outside dimensions Displays buffer memory of special units and special blocks The display area of the 5DM shows the following.
Buffer memory monitor function
When installed to a PLC (offered only in FX1N Series).
➀ ➁ ➂ ➃➄ ➀ "RUN": Displayed while the PLC is running, and not displayed while
2 40 Displays error code and error occurrence step No. when a PLC the PLC is stopped.
(0.07) (1.57) Error display function
error has occurred.
9 26 RUN BFM ON R D
➁ "BFM": Displays the contents of the buffer memory when a special
(0.35) (1.03) Forced set/reset function Forces ON and OFF bit devices Y, M and S. ➅ TCD
Note: These dimensions XYMS
- ➇ block is connected (only in the FX1N Series).
T/C reset function Clears current value of T and C (current value: 0, contact: OFF).
(0.86)

(1.1)
22

28

measured
from the left side
Data change function ➆ ➈ ➂ "ON/OFF": Displayed while T or C is ON in the word device monitor
are common Current value change Change current value of T, C and D. function, and not displayed while T or C is OFF.
(0.55)
2.6(0.1)

FX1S Series
(1.25)
14

➃ "R" (reset): Displayed while T or C is reset.

32

to the FX1S and Set value change Change set value of T and C.
FX1N Series.
5DM control functions: The 5DM is controlled by sequence programs.
4.6 FX1N Series ➄ "D" (32-bit): Displayed when a 32-bit D is specified.
(0.18) For use of these functions, refer to the FX Series Programming Manual ΙΙ
(0.29)

10 8 8 8
7.5

➅ Device type: Displays the device type (T, C, D, X, Y, M or S) currently

(0.39) (0.31) (0.31) (0.31)
(1.41)
36

Function Description
being displayed.
Enables full use of all operator functions, enables only monitor
Protect function
function or enables only clock time display function. ➆ Device No.: Displays the device No. currently being displayed.
Unit: mm (inches) Allows to specify device type and device No. to be displayed in
Outer painting color: Munsell 0.08GY/7.64/0.81 Specified device monitor function
5DM. ➇ Current value: Displays the current value of T, C or D.
Mass: 20 g (0.05 lbs) Error display enable/disable
Enables or disables error display function (operator function). ➈ Set value: Displays the set value of T or C.
function
Automatic backlight OFF function Allows to set automatic backlight OFF time (initial value: 10 min). * In the case of 32-bit C or D, upper 5 digits are displayed in ➇ and the
Operation key status recognition lower 5 digits are displayed in ➈.
Recognizes ON/OFF status of four operation keys.
function
5. Operation List <Monitoring 16-bit T or 16-bit C >
➀ <Changing the current value/set value of 16-bit T or 16-bit C>
The process for the operator functions are shown below. RUN
1 T + OK + OK
• The operation keys are expressed as follows. Changing the ➄ Determine
current value the input.
ESC : ESC key - : "-" key + : "+" key OK : OK key - OK OK OK - <Resetting the current value>
➁ ➂ Changing the ➃
set value
OK OK
Time display screen (when the power is turned on) ➅ Press and hold it for ➅
➀ "ON" is displayed when T or C is ON and "R" is displayed while resetting. 2 seconds or more.
➁ Change over the device to monitor.
RUN <Setting the time> ➁ T or C that is not used in the program is not displayed.
OK + OK ➀ An item being changed flickers. (A horizontal line "-" is displayed if there is none of T or C in the program.)
➁ Set "year, month, day, hour and minute" in this order. ➂ When the OK key is pressed once, the current value is changed, and when the OK key is pressed three times, the set value is changed. (Flickers while changing)
Press and hold +1 Determine When the OK key is pressed at "minute" set up, the setting operation will be completed.
➃ Press the "+" key to increase the value. Press the "-" key to decrease the value.
it for 2 seconds
- the input. ➄ Press the OK key to determine the input. At this time, the input data is written to the PLC.
or more. ➀ ➁ ➅ When the OK key is pressed and held for 2 seconds or more while the current value is changed, the current value is reset to "0" and the contact turns off.
-1 When the OK key is pressed once again, the current value reset operation will be completed.
<Selecting a device>
➂
OK TCD + OK To 1 <Monitoring 32-bit C>
XYMS Determine Current value <Changing the current set value of 32-bit C>
the input. RUN D
-
1 C OK + OK
Program error Keyword error ➁ ➃Determine
the input.
(Entry code error) ➂ Select an either device using the "+" and "-" keys.
(In the initial status, "D" flickers.) - <Resetting the current value>
T, C, D (16-bit), D (32-bit), X, Y, M, S or BFM ➀ ➂ OK OK
"-" key "+" key ➄Press and hold it for ➄
(Error display) + - 2 seconds or more.
Refer to error display.
* "BFM" is displayed only when the FX1N Series PLC is used.
RUN D
<Monitoring a bit device (X/Y/M/S)> <Forced setting/resetting a bit device (Y/M/S)> C ➀ Press the "+" or "-" key to change over the current value and the set value. For the set value, "S" is added in a
S right position above the device No.
RUN RUN
➁ When the OK key is pressed, the current value or the set value is changed.
1 + OK + OK OK ➂ Press the "+" key to increase the value. Press the "-" key to decrease the value.
➂ ➃ Press the OK key to determine the input. At this time, the input data is written to the PLC.
Y Y Set or reset the bit Set value
➄ When the OK key is pressed and held for 2 seconds or more while the current value is changed, the current value
device. is reset to "0" and the contact turns off.
- -
➄ When the OK key is pressed once again, the current value reset operation will be completed.
➁ ➃
➀ ➂

➀ From the displayed device No., the ON/OFF ➂ Forced set/reset mode ➃ Select a device No. <Monitoring 16-bit D>
status of 8 points (in the case of X or Y) or 10 A selected device is indicated with underline. <Changing the current value of 16-bit D>
points (in the case of M or S) is indicated.
: OFF status : ON status ➄ The current ON/OFF status is reversed. 1
RUN
+ OK OK
* The device turns on and off alternately when the OK key is D +
Underline flickers.
➁ Eight points (in the case of X or Y) or 10 points pressed. ➁ ➃
(in the case of M or S) are scrolled at a time. If the OK key is pressed while the device is ON, it turns off.
"+" key: Scrolls toward larger device Nos. If the OK key is pressed while the device is OFF, it turns on. - -
" - " key: Scrolls toward smaller device Nos. ➀ ➂
➀ D is scrolled by 1 point at a time.
➁ Select the current value change mode.
<BFM unit selection> ➂ Press the "+" key to increase the value. Press the "-" key to decrease the value.
S: State ➃ Press the OK key to determine the input. At this time, the input data is written to the PLC.

+ - <Monitoring 32-bit D>

<Buffer memory No. selection> <Changing the current value of 32-bit D>
RUN D
<Buffer memory change> 1 + OK + OK
BFM BFM D
1 OK + OK + OK ➁ ➃
➁ ➇ - -
- OK - ➀ ➂
➄ Press and hold ➆ ➀ D is scrolled by 2 points at a time by the "+" key and by 1 point at a time by the "-" key.
➂ ➃ for 2 sec or more. ➁ Select the current value change mode.
➀ + - ➅ ➂ Press the "+" key to increase the value. Press the "-" key to decrease the value.
➀ If a special block is connected to the FX1N Series when you select a device, a buffer memory (hereafter referred to as "BFM") is ➃ Press the OK key to determine the input. At this time, the input data is written to the PLC.
BFM displayed. A displayed numeric value indicates the unit No.
➁ When you press the OK key, BFM monitor starts for the unit having the displayed unit No.
➂ The BFM No. is displayed. ➃ The BFM current value is displayed. ➄Select the BFM No. <Keyword (Entry code) error
➅ After pressing the OK key, you can change the value of the displayed BFM No. Every time you press and hold the OK key for 2 <Error display> display>
seconds or more, the display changes over alternately between 16-bit BFM and 32-bit BFM.
When an keyword (entry code) has been input to the PLC, only the
➆ Increase or decrease the BFM current value using the "+" or "-" key. ➀ Error step No.
➇ Write the data you have input to the BFM. ➁ Error code
time can be displayed.
If you press the OK key while the time is displayed, the error message
+ -
CAUTION shown on the left flickers for 5 seconds.
Depending on the type of the connected special block, the BFM is cleared when the power is turned off or the mode is changed Press the ESC key or Release the keyword (entry code) in a peripheral unit such as
over between RUN and STOP. When using a special unit, write the data finally to the BFM using a sequence program (using FNC release the error status to the FX-10P/20P and the personal computer software for creating
T: Timer
delete the error display.
79 TO instruction (write to BFM).) ➀ ➁ sequence programs.

Guidelines for the safety of the user and protection of the Micro Display Module Attention
FX1N-5DM Manual number : JY992D84901
• This product is designed for use in industrial applications.
• This manual has been written to be used by trained and competent personnel. This is defined by
the European directives for machinery, low voltage and EMC. Note Manual revision : G
• If in doubt at any stage during the installation of the Micro Display Module FX1N-5DM always • Authorized Representative in the European Community:
consult a professional electrical engineer who is qualified and trained to the local and national Date : April 2015
standards. If in doubt about the operation or use of the Micro Display Module FX1N-5DM please Mitsubishi Electric Europe B.V.
consult the nearest Mitsubishi Electric distributor. Gothaer Str. 8, 40880 Ratingen, Germany
• Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential
damage that may arise as a result of the installation or use of this equipment.
• All examples and diagrams shown in this manual are intended only as an aid to understanding the HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310 JAPAN
text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of the This manual confers no industrial property rights or any rights of any other
product based on these illustrative examples. kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation JY992D84901G Effective April 2015
• Owing to the very great variety in possible application of this equipment, you must satisfy yourself cannot be held responsible for any problems involving industrial property
Specifications are subject to change without notice
as to its suitability for your specific application. rights which may occur as a result of using the contents noted in this manual.
5. Operation List <Monitoring 16-bit T or 16-bit C >
➀ <Changing the current value/set value of 16-bit T or 16-bit C>
The process for the operator functions are shown below. RUN
1 T + OK + OK
• The operation keys are expressed as follows. Changing the ➄ Determine
current value the input.
ESC : ESC key - : "-" key + : "+" key OK : OK key - OK OK OK - <Resetting the current value>
➁ ➂ Changing the ➃
set value
OK OK
Time display screen (when the power is turned on) ➅ Press and hold it for ➅
➀ "ON" is displayed when T or C is ON and "R" is displayed while resetting. 2 seconds or more.
➁ Change over the device to monitor.
RUN <Setting the time> ➁ T or C that is not used in the program is not displayed.
OK + OK ➀ An item being changed flickers. (A horizontal line "-" is displayed if there is none of T or C in the program.)
➁ Set "year, month, day, hour and minute" in this order. ➂ When the OK key is pressed once, the current value is changed, and when the OK key is pressed three times, the set value is changed. (Flickers while changing)
Press and hold +1 Determine When the OK key is pressed at "minute" set up, the setting operation will be completed.
➃ Press the "+" key to increase the value. Press the "-" key to decrease the value.
it for 2 seconds
- the input. ➄ Press the OK key to determine the input. At this time, the input data is written to the PLC.
or more. ➀ ➁ ➅ When the OK key is pressed and held for 2 seconds or more while the current value is changed, the current value is reset to "0" and the contact turns off.
-1 When the OK key is pressed once again, the current value reset operation will be completed.
<Selecting a device>
➂
OK TCD + OK To 1 <Monitoring 32-bit C>
XYMS Determine Current value <Changing the current set value of 32-bit C>
the input. RUN D
-
1 C OK + OK
Program error Keyword error ➁ ➃Determine
the input.
(Entry code error) ➂ Select an either device using the "+" and "-" keys.
(In the initial status, "D" flickers.) - <Resetting the current value>
T, C, D (16-bit), D (32-bit), X, Y, M, S or BFM ➀ ➂ OK OK
"-" key "+" key ➄Press and hold it for ➄
(Error display) + - 2 seconds or more.
Refer to error display.
* "BFM" is displayed only when the FX1N Series PLC is used.
RUN D
<Monitoring a bit device (X/Y/M/S)> <Forced setting/resetting a bit device (Y/M/S)> C ➀ Press the "+" or "-" key to change over the current value and the set value. For the set value, "S" is added in a
S right position above the device No.
RUN RUN
➁ When the OK key is pressed, the current value or the set value is changed.
1 + OK + OK OK ➂ Press the "+" key to increase the value. Press the "-" key to decrease the value.
➂ ➃ Press the OK key to determine the input. At this time, the input data is written to the PLC.
Y Y Set or reset the bit Set value
➄ When the OK key is pressed and held for 2 seconds or more while the current value is changed, the current value
device. is reset to "0" and the contact turns off.
- -
➄ When the OK key is pressed once again, the current value reset operation will be completed.
➁ ➃
➀ ➂

➀ From the displayed device No., the ON/OFF ➂ Forced set/reset mode ➃ Select a device No. <Monitoring 16-bit D>
status of 8 points (in the case of X or Y) or 10 A selected device is indicated with underline. <Changing the current value of 16-bit D>
points (in the case of M or S) is indicated.
: OFF status : ON status ➄ The current ON/OFF status is reversed. 1
RUN
+ OK OK
* The device turns on and off alternately when the OK key is D +
Underline flickers.
➁ Eight points (in the case of X or Y) or 10 points pressed. ➁ ➃
(in the case of M or S) are scrolled at a time. If the OK key is pressed while the device is ON, it turns off.
"+" key: Scrolls toward larger device Nos. If the OK key is pressed while the device is OFF, it turns on. - -
" - " key: Scrolls toward smaller device Nos. ➀ ➂
➀ D is scrolled by 1 point at a time.
➁ Select the current value change mode.
<BFM unit selection> ➂ Press the "+" key to increase the value. Press the "-" key to decrease the value.
S: State ➃ Press the OK key to determine the input. At this time, the input data is written to the PLC.

+ - <Monitoring 32-bit D>

<Buffer memory No. selection> <Changing the current value of 32-bit D>
RUN D
<Buffer memory change> 1 + OK + OK
BFM BFM D
1 OK + OK + OK ➁ ➃
➁ ➇ - -
- OK - ➀ ➂
➄ Press and hold ➆ ➀ D is scrolled by 2 points at a time by the "+" key and by 1 point at a time by the "-" key.
➂ ➃ for 2 sec or more. ➁ Select the current value change mode.
➀ + - ➅ ➂ Press the "+" key to increase the value. Press the "-" key to decrease the value.
➀ If a special block is connected to the FX1N Series when you select a device, a buffer memory (hereafter referred to as "BFM") is ➃ Press the OK key to determine the input. At this time, the input data is written to the PLC.
BFM displayed. A displayed numeric value indicates the unit No.
➁ When you press the OK key, BFM monitor starts for the unit having the displayed unit No.
➂ The BFM No. is displayed. ➃ The BFM current value is displayed. ➄Select the BFM No. <Keyword (Entry code) error
➅ After pressing the OK key, you can change the value of the displayed BFM No. Every time you press and hold the OK key for 2 <Error display> display>
seconds or more, the display changes over alternately between 16-bit BFM and 32-bit BFM.
When an keyword (entry code) has been input to the PLC, only the
➆ Increase or decrease the BFM current value using the "+" or "-" key. ➀ Error step No.
➇ Write the data you have input to the BFM. ➁ Error code
time can be displayed.
If you press the OK key while the time is displayed, the error message
+ -
CAUTION shown on the left flickers for 5 seconds.
Depending on the type of the connected special block, the BFM is cleared when the power is turned off or the mode is changed Press the ESC key or Release the keyword (entry code) in a peripheral unit such as
over between RUN and STOP. When using a special unit, write the data finally to the BFM using a sequence program (using FNC release the error status to the FX-10P/20P and the personal computer software for creating
T: Timer
delete the error display.
79 TO instruction (write to BFM).) ➀ ➁ sequence programs.

Guidelines for the safety of the user and protection of the Micro Display Module Attention
FX1N-5DM Manual number : JY992D84901
• This product is designed for use in industrial applications.
• This manual has been written to be used by trained and competent personnel. This is defined by
the European directives for machinery, low voltage and EMC. Note Manual revision : G
• If in doubt at any stage during the installation of the Micro Display Module FX1N-5DM always • Authorized Representative in the European Community:
consult a professional electrical engineer who is qualified and trained to the local and national Date : April 2015
standards. If in doubt about the operation or use of the Micro Display Module FX1N-5DM please Mitsubishi Electric Europe B.V.
consult the nearest Mitsubishi Electric distributor. Gothaer Str. 8, 40880 Ratingen, Germany
• Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential
damage that may arise as a result of the installation or use of this equipment.
• All examples and diagrams shown in this manual are intended only as an aid to understanding the HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310 JAPAN
text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of the This manual confers no industrial property rights or any rights of any other
product based on these illustrative examples. kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation JY992D84901G Effective April 2015
• Owing to the very great variety in possible application of this equipment, you must satisfy yourself cannot be held responsible for any problems involving industrial property
Specifications are subject to change without notice
as to its suitability for your specific application. rights which may occur as a result of using the contents noted in this manual.
 1.4 Name of each part Cautions:

➀ ESC key: Cancels the last key operation or returns to the previous screen. 1) If a keyword to prohibit read, write or read and write of programs is registered in the PLC, only the
➄ ➁ "-" key: Scrolls the device No. to a smaller one or decrements a numeric clock time display function is available. Any other function shown above is not available.
value by. If any operation is performed in the 5DM when a keyword is registered in the PLC, the error display
➂ "+" key: Scrolls the device No. to a larger one or increments a numeric flickers for 5 seconds.
value. 2) The automatic backlight OFF function is set to 10 minutes as the initial value. As far as the OFF time
➃ OK key: Determines the display device, executes write of a numeric value, is not changed by a sequence program, the backlight turns off 10 minutes later.
or changes over forced setting and forced resetting.
➅ If any key is pressed after the backlight turns off, the contents displayed just before the backlight turns
➀ ➁ ➂ ➃
➄ Display area: Displays the current time and the monitored device status. off appear again. A key pressed for the first time after the backlight turns off is regarded as a trigger to
➆ ➅ Connector for PLC turn on the backlight, and is not regarded as a key operation.
➆ 5DM mounting hook
4.2 Control devices for 5DM
2. Installation When using the 5DM control function, specify data registers (D) and auxiliary relays (M) used to control
DISPLAY MODULE FX1N-5DM the 5DM to special data registers D8158 and D8159.
Install the 5DM to the PLC using the following procedure. Five data registers and 15 auxiliary relays are occupied for control of the 5DM.
USER’S MANUAL A) Top cover for DM (offered as an accessory of 5DM)
B) Connector for optional equipment
For the control device use procedure, refer to the FX1S/FX1N/FX2N/FX2NC Series Programming Manual.
C) M3 screw to fix top cover Special D Control device Description Application
JY992D84901G
• Remove the top cover of the basic unit, and attach the top cover for DM D{ Device type to be displayed *1 For specified device
A) instead. D{+1 Device No. to be displayed monitor function
Plug the 5DM in to the connector B). D8158 For automatic backlight
D{+2 Backlight OFF time (min)
This manual only describes the specifications for Display Module FX1N-5DM. • If the 5DM is always used, the top cover can be fixed with the M3 screw K{ OFF function
For complete operation, wiring, mounting and programming instructions please refer to the FX1S, FX1N C). (Tightening torque: 0.3 to 0.6 Nxm) D{+3 Protects display screen. *2 For protect function
HARDWARE MANUAL and PROGRAMMING MANUAL.
If the 5DM is used together with a function expansion board, remove and D{+4 Not available.
These manuals should be read and understood before attempting to install or use the unit.
attach the 5DM by pressing the 5DM mounting hook provided at the bottom M… Requests edition of displayed device data. For specified device
of the 5DM.
M…+1 Edition completion response monitor function

3. Specifications Disables backlight OFF function. For automatic backlight

M…+2
(Turns on backlight forcedly.) OFF function
Related Manuals M…+3 Displays or hides operation errors, etc. *3 Others
3.1 Environmental specifications
Manual name Manual No. Description The environmental specifications are equivalent to those of the PLC main unit. (Refer to the handy manual M…+4 ESC key status *4
offered with the FX1S/FX1N Series PLC main unit.) M…+5 "-" key status *4 For specified device
Describes contents related to hardware of FX1S Series
FX1S Series Hardware M…+6 "+" key status *4 monitor function
JY992D83901 PLC such as specifications, wiring and installation. 3.2 Power supply specifications D8159
Manual
(It is offered with FX1S Series PLC basic unit.) The power is supplied from the PLC main unit. K… M…+7 OK key status *4
Describes contents related to hardware of FX1N Series 5V DC, 110 mA M…+8 Not available.
FX1N Series Hardware
JY992D88201 PLC such as specifications, wiring and installation. M…+9 Not available.
Manual
(It is offered with FX1N Series PLC basic unit.) 4. Outline of Performance M…+10 Not available.
FX Series M…+11 Not available.
JY992D88101 Describes instructions in FX1S/FX1N/FX2N/FX2NC Series. This section describes the function list of the 5DM.
Programming Manual II
The operator functions available with the operation keys of the 5DM are described on the back of this manual. M…+12 Not available.
For the 5DM control functions available from the PLC, refer to the FX1S/FX1N/FX2N/FX2NC Series Program- M…+13 Not available.
ming Manual.
1. Outline of Product M…+14 Not available.
4.1 Function list
*1 Input numeric values correspond to the devices as follows.
1.1 Features Symbols stand for the following. 1: Input (X) 2: Output (Y) 3: Auxiliary relay (M) 4: State (S) 5: Timer (T)
X: Input Y: Output M: Auxiliary relay S: State T: Timer C: Counter D: Data register 6: Counter (C), 16-bit (current value/set value) and 32-bit (set value)
The micro display module FX1N-5DM (hereafter referred to as "5DM") is
BFM: Butter memory of special units and special blocks 7: Data register (D), 16-bit8: Data register (D), 32-bit 9: Time display
mounted on the top face of the FX1S/FX1N Series PLC basic unit and
can monitor/update internal PLC data. Operator functions: The operator can use these functions by using only the operation keys of the 5DM. 10: Counter (C), 16-bit (current value/set value) and 32-bit (current value)
Refer to the simplified chart of operations shown on the back face of this manual. *2 0: Enables all operations. 1: Enables only the time display function.
Function Description 2: Enables only the monitor function.
PLCs installed to: FX1S and FX1N Series
Clock function *3 PC hardware errors, parameter errors, grammatical errors and circuit errors are unconditionally displayed.
Display Displays current time of clock function (built in FX1S/FX1N Series). While this bit is ON, I/O configuration errors, parallel link errors and operation errors are also displayed.
Setting Allows to set time (year, month, day, hour and minute). *4 Every operation key is the momentary type, and functions as follows:
1.2 Product configuration Device monitor function While a key is pressed and held: ON
Bit device monitor Displays ON/OFF status of X, Y, M and S. While key is not pressed: OFF
Main unit : FX1N-5DM Word device (16-bit) monitor Displays current and set values of T and C and current value of D.
Accessories : Top cover for DM 1, M3 screw to mount top cover 1 4.3 Description on display area
Word device (32-bit) monitor Displays current and set values of 32-bit C and current value of D.
1.3 Outside dimensions Displays buffer memory of special units and special blocks The display area of the 5DM shows the following.
Buffer memory monitor function
When installed to a PLC (offered only in FX1N Series).
➀ ➁ ➂ ➃➄ ➀ "RUN": Displayed while the PLC is running, and not displayed while
2 40 Displays error code and error occurrence step No. when a PLC the PLC is stopped.
(0.07) (1.57) Error display function
error has occurred.
9 26 RUN BFM ON R D
➁ "BFM": Displays the contents of the buffer memory when a special
(0.35) (1.03) Forced set/reset function Forces ON and OFF bit devices Y, M and S. ➅ TCD
Note: These dimensions XYMS
- ➇ block is connected (only in the FX1N Series).
T/C reset function Clears current value of T and C (current value: 0, contact: OFF).
(0.86)

(1.1)
22

28

measured
from the left side
Data change function ➆ ➈ ➂ "ON/OFF": Displayed while T or C is ON in the word device monitor
are common Current value change Change current value of T, C and D. function, and not displayed while T or C is OFF.
(0.55)
2.6(0.1)

FX1S Series
(1.25)
14

➃ "R" (reset): Displayed while T or C is reset.

32

to the FX1S and Set value change Change set value of T and C.
FX1N Series.
5DM control functions: The 5DM is controlled by sequence programs.
4.6 FX1N Series ➄ "D" (32-bit): Displayed when a 32-bit D is specified.
(0.18) For use of these functions, refer to the FX Series Programming Manual ΙΙ
(0.29)

10 8 8 8
7.5

➅ Device type: Displays the device type (T, C, D, X, Y, M or S) currently

(0.39) (0.31) (0.31) (0.31)
(1.41)
36

Function Description
being displayed.
Enables full use of all operator functions, enables only monitor
Protect function
function or enables only clock time display function. ➆ Device No.: Displays the device No. currently being displayed.
Unit: mm (inches) Allows to specify device type and device No. to be displayed in
Outer painting color: Munsell 0.08GY/7.64/0.81 Specified device monitor function
5DM. ➇ Current value: Displays the current value of T, C or D.
Mass: 20 g (0.05 lbs) Error display enable/disable
Enables or disables error display function (operator function). ➈ Set value: Displays the set value of T or C.
function
Automatic backlight OFF function Allows to set automatic backlight OFF time (initial value: 10 min). * In the case of 32-bit C or D, upper 5 digits are displayed in ➇ and the
Operation key status recognition lower 5 digits are displayed in ➈.
Recognizes ON/OFF status of four operation keys.
function
5. Operation List <Monitoring 16-bit T or 16-bit C >
➀ <Changing the current value/set value of 16-bit T or 16-bit C>
The process for the operator functions are shown below. RUN
1 T + OK + OK
• The operation keys are expressed as follows. Changing the ➄ Determine
current value the input.
ESC : ESC key - : "-" key + : "+" key OK : OK key - OK OK OK - <Resetting the current value>
➁ ➂ Changing the ➃
set value
OK OK
Time display screen (when the power is turned on) ➅ Press and hold it for ➅
➀ "ON" is displayed when T or C is ON and "R" is displayed while resetting. 2 seconds or more.
➁ Change over the device to monitor.
RUN <Setting the time> ➁ T or C that is not used in the program is not displayed.
OK + OK ➀ An item being changed flickers. (A horizontal line "-" is displayed if there is none of T or C in the program.)
➁ Set "year, month, day, hour and minute" in this order. ➂ When the OK key is pressed once, the current value is changed, and when the OK key is pressed three times, the set value is changed. (Flickers while changing)
Press and hold +1 Determine When the OK key is pressed at "minute" set up, the setting operation will be completed.
➃ Press the "+" key to increase the value. Press the "-" key to decrease the value.
it for 2 seconds
- the input. ➄ Press the OK key to determine the input. At this time, the input data is written to the PLC.
or more. ➀ ➁ ➅ When the OK key is pressed and held for 2 seconds or more while the current value is changed, the current value is reset to "0" and the contact turns off.
-1 When the OK key is pressed once again, the current value reset operation will be completed.
<Selecting a device>
➂
OK TCD + OK To 1 <Monitoring 32-bit C>
XYMS Determine Current value <Changing the current set value of 32-bit C>
the input. RUN D
-
1 C OK + OK
Program error Keyword error ➁ ➃Determine
the input.
(Entry code error) ➂ Select an either device using the "+" and "-" keys.
(In the initial status, "D" flickers.) - <Resetting the current value>
T, C, D (16-bit), D (32-bit), X, Y, M, S or BFM ➀ ➂ OK OK
"-" key "+" key ➄Press and hold it for ➄
(Error display) + - 2 seconds or more.
Refer to error display.
* "BFM" is displayed only when the FX1N Series PLC is used.
RUN D
<Monitoring a bit device (X/Y/M/S)> <Forced setting/resetting a bit device (Y/M/S)> C ➀ Press the "+" or "-" key to change over the current value and the set value. For the set value, "S" is added in a
S right position above the device No.
RUN RUN
➁ When the OK key is pressed, the current value or the set value is changed.
1 + OK + OK OK ➂ Press the "+" key to increase the value. Press the "-" key to decrease the value.
➂ ➃ Press the OK key to determine the input. At this time, the input data is written to the PLC.
Y Y Set or reset the bit Set value
➄ When the OK key is pressed and held for 2 seconds or more while the current value is changed, the current value
device. is reset to "0" and the contact turns off.
- -
➄ When the OK key is pressed once again, the current value reset operation will be completed.
➁ ➃
➀ ➂

➀ From the displayed device No., the ON/OFF ➂ Forced set/reset mode ➃ Select a device No. <Monitoring 16-bit D>
status of 8 points (in the case of X or Y) or 10 A selected device is indicated with underline. <Changing the current value of 16-bit D>
points (in the case of M or S) is indicated.
: OFF status : ON status ➄ The current ON/OFF status is reversed. 1
RUN
+ OK OK
* The device turns on and off alternately when the OK key is D +
Underline flickers.
➁ Eight points (in the case of X or Y) or 10 points pressed. ➁ ➃
(in the case of M or S) are scrolled at a time. If the OK key is pressed while the device is ON, it turns off.
"+" key: Scrolls toward larger device Nos. If the OK key is pressed while the device is OFF, it turns on. - -
" - " key: Scrolls toward smaller device Nos. ➀ ➂
➀ D is scrolled by 1 point at a time.
➁ Select the current value change mode.
<BFM unit selection> ➂ Press the "+" key to increase the value. Press the "-" key to decrease the value.
S: State ➃ Press the OK key to determine the input. At this time, the input data is written to the PLC.

+ - <Monitoring 32-bit D>

<Buffer memory No. selection> <Changing the current value of 32-bit D>
RUN D
<Buffer memory change> 1 + OK + OK
BFM BFM D
1 OK + OK + OK ➁ ➃
➁ ➇ - -
- OK - ➀ ➂
➄ Press and hold ➆ ➀ D is scrolled by 2 points at a time by the "+" key and by 1 point at a time by the "-" key.
➂ ➃ for 2 sec or more. ➁ Select the current value change mode.
➀ + - ➅ ➂ Press the "+" key to increase the value. Press the "-" key to decrease the value.
➀ If a special block is connected to the FX1N Series when you select a device, a buffer memory (hereafter referred to as "BFM") is ➃ Press the OK key to determine the input. At this time, the input data is written to the PLC.
BFM displayed. A displayed numeric value indicates the unit No.
➁ When you press the OK key, BFM monitor starts for the unit having the displayed unit No.
➂ The BFM No. is displayed. ➃ The BFM current value is displayed. ➄Select the BFM No. <Keyword (Entry code) error
➅ After pressing the OK key, you can change the value of the displayed BFM No. Every time you press and hold the OK key for 2 <Error display> display>
seconds or more, the display changes over alternately between 16-bit BFM and 32-bit BFM.
When an keyword (entry code) has been input to the PLC, only the
➆ Increase or decrease the BFM current value using the "+" or "-" key. ➀ Error step No.
➇ Write the data you have input to the BFM. ➁ Error code
time can be displayed.
If you press the OK key while the time is displayed, the error message
+ -
CAUTION shown on the left flickers for 5 seconds.
Depending on the type of the connected special block, the BFM is cleared when the power is turned off or the mode is changed Press the ESC key or Release the keyword (entry code) in a peripheral unit such as
over between RUN and STOP. When using a special unit, write the data finally to the BFM using a sequence program (using FNC release the error status to the FX-10P/20P and the personal computer software for creating
T: Timer
delete the error display.
79 TO instruction (write to BFM).) ➀ ➁ sequence programs.

Guidelines for the safety of the user and protection of the Micro Display Module Attention
FX1N-5DM Manual number : JY992D84901
• This product is designed for use in industrial applications.
• This manual has been written to be used by trained and competent personnel. This is defined by
the European directives for machinery, low voltage and EMC. Note Manual revision : G
• If in doubt at any stage during the installation of the Micro Display Module FX1N-5DM always • Authorized Representative in the European Community:
consult a professional electrical engineer who is qualified and trained to the local and national Date : April 2015
standards. If in doubt about the operation or use of the Micro Display Module FX1N-5DM please Mitsubishi Electric Europe B.V.
consult the nearest Mitsubishi Electric distributor. Gothaer Str. 8, 40880 Ratingen, Germany
• Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential
damage that may arise as a result of the installation or use of this equipment.
• All examples and diagrams shown in this manual are intended only as an aid to understanding the HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310 JAPAN
text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of the This manual confers no industrial property rights or any rights of any other
product based on these illustrative examples. kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation JY992D84901G Effective April 2015
• Owing to the very great variety in possible application of this equipment, you must satisfy yourself cannot be held responsible for any problems involving industrial property
Specifications are subject to change without notice
as to its suitability for your specific application. rights which may occur as a result of using the contents noted in this manual.