Amerlock 400AL/AL WN

High Solids Epoxy Coating

Product Data Physical Data

Finish ........................................... semi-gloss
Colour .......................................... aluminium
Substrate ..................................... tightly adhering existing
coatings, mechanically cleaned
• Amerlock 400AL is a surface tolerant maintenance steel
coating which can be applied to mechanically Components ................................ 2
cleaned surfaces Curing mechanism ....................... solvent release and chemical
reaction between components
• Amerlock 400AL WN Wintergrade version can be Volume solids
applied at temperatures down to 0°C 400AL ....................................... 85% (ASTM-D2697 modified) *
400AL WN ................................ 79% (ASTM-D2697 modified) *
• Gives performance superior to conventional coatings VOC
when applied over mechanically cleaned surfaces 400AL ....................................... 11% by weight/ 150 g/l
400AL WN ................................ 12% by weight/ 145 g/l
• Contains special ingredients which wet the surface Dry film thickness ......................... 125 µm per coat
and penetrate any traces of existing rust Number of coats .......................... 1-2
Calculated coverage
• Can be applied over most existing coatings and can 400AL ....................................... 6.8 m²/l at 125 µm
be topcoated with a wide range of topcoats 400AL WN ................................ 6.3 m²/l at 125 µm
Allow for application losses, surface irregularities, etc.
• High solids, VOC * compliant
• Compatible with prepared damp surfaces Application methods ..................... airless or conventional spray,
brush or roller
Potlife
Typical Uses 400AL ....................................... 4 hours at 20°C
400AL WN ................................ 3 hours at 10°C
Amerlock 400AL is most often used in those areas where Drying times at 125 µm dft 400AL(20°C) 400ALWN(10°C)
blasting is impractical or impossible. Uses include steel dry to touch 6 hours 7 hours
structures in industrial facilities, bridges, tanks, marine dry to handle 24 hours 14 hours (min.)
dry to recoat 16 hours 16 hours
weathering, oil tanks, piping, roofs, water towers and other
exposures subject to high humidity and moisture. Amerlock Maximum interval for topcoating depends on coating system to be
400AL has good resistance to splash/spillage and fumes of used. Consult your Ameron representative for specific
recommendations. Potlife and drying times are dependent on
acids, alkalies. solvents and fresh and salt water. Amerlock temperature.
400AL can be applied over damp substrates. For immersion
Induction time (at 20°C) ............... not applicable
in potable and seawater, abrasive blasting to Sa 2½ is Mixing ratio (by volume)
required. For cold climates a special wintergrade version, resin .......................................... 1 part
Amerlock 400AL WN is available for use in temperature cure ........................................... 1 part
Thinner ......................................... Amercoat 9HF
between 0°C and 20°C Cleaner ........................................ Amercoat 12
Specific gravity
400AL ....................................... 1.31 kg/l (mixed product)
Outstanding Characteristics 400AL WN ................................ 1.23 kg/l (mixed product)
Amerlock 400AL is a high performance coating, which can Flash points (Closed Cup) ........... 400AL 400AL WN
resin .......................................... 51°C 23°C
be applied to mechanically cleaned surfaces. Adhesion is cure ........................................... 24°C 43°C
excellent to a wide variety of substrates. Amerlock 400AL Amercoat 9HF ........................... 26°C 26°C
Amercoat 12 .............................. -1°C -1°C
has excellent application characteristics. It can be applied by Packaging (400AL and 400AL WN)
brush, roller, conventional and airless spray equipment. resin .......................................... 10 l in 20 l can
cure ........................................... 10 l in 10 l can
Shipping weight ............................ 400AL 400AL WN
Recommended Systems resin .......................................... ± 13.9 kg 13.3 kg
Amerlock 400AL can be topcoated with a wide range of cure ........................................... ± 15.7 kg 14.5 kg
Shelf life ....................................... 2 years from shipment date
topcoats for a finish colour scheme or for added chemical when stored indoors in
resistance. Contact your Ameron representative for special unopened, original containers
at 5 to 40°C.
recommendations.
* Volume solids is measured in accordance with ASTM D2697
Approvals and Certificates modified. Slight variations ±3% may occur due to colour and testing
variances.
Amerlock 400AL may be used for the transport of grain, as
certified by the North of England Industrial Health Service.
Complies with COT 16.75 and CCOT 17.09 (specifications
for epoxy primer and sealer).

* VOC = Volatile Organic Compounds - U.S. regulations for the reduction of

solvent emission.

AL400Alp - R29/10/98; supersedes R10/12/97

Application Data Summary Safety
For complete information on procedures, equipment Since improper use and handling can be hazardous to health and cause fire or
explosion, safety precautions included with application instructions must be
and safety precautions, see application instructions. observed during all storage, handling, use and drying periods. To avoid any
Like all high performance coatings, Amerlock confusion that may arise through translation into other languages, the English
version of the Product Data/Application instructions will be the governing literature
400AL/AL WN must be applied as recommended to and must be referred to in case of deviations with product literature in other
obtain the maximum protection for which this coating languages.

is formulated. Warranty
Ameron warrants its products to be free from defects in material and workmanship.
SURFACE PREPARATION/EQUIPMENT -Refer to Ameron’s sole obligations and Buyer’s exclusive remedy in connection with the
application instructions for Amerlock 400AL as well as products shall be limited, at Ameron’s option, to either replacement of products not
conforming to this warranty or credit to Buyer’s account in the invoiced amount of
application instructions for primer and intermediate the nonconforming products. Any claim under this warranty must be made by Buyer
to Ameron in writing within five (5) days of Buyer’s discovery of the claimed defect,
coat(s). but in no event later than the expiration of the applicable shelf life, or one year from
the delivery date, whichever is earlier. Buyer’s failure to notify Ameron of such
nonconformance as required herein shall bar Buyer from recovery under this
warranty.

Ameron makes no other warranties concerning the product. No other

warranties, whether express, implied, or statutory, such as warranties of
merchantability or fitness for a particular purpose, shall apply. In no event
shall Ameron be liable for consequential or incidental damages.

Any recommendation or suggestion relating to the use of the products made by

Ameron, whether in its technical literature, or response to specific enquiry, or
otherwise, is based on data believed to be reliable; however, the products and
information are intended for use by Buyer’s having requisite skill and know-how in
the industry, and therefore it is Buyer to satisfy itself of the suitability of the products
for its own particular use and it shall be deemed that Buyer has done so, as its sole
discretion and risk. Variation in environment, changes in procedures of use, or
extrapolation of data may cause unsatisfactory results.

Limitation of Liability
Ameron’s liability on any claim of any kind, including claims based upon Ameron’s
negligence or strict liability, for any loss or damage arising out of, connected with, or
resulting from the use of the products, shall in no case exceed the purchase price
allocable to the products or part thereof which give rise to the claim. In no event
shall Ameron be liable for consequential or incidental damages.

Conditions of Sale
All our transactions are subject to our Terms and Conditions of Sale.

Performance Coatings & Performance Coatings & Performance Coatings & Performance Coatings &
Finishes Europe Finishes/USA Finishes/Australia Finishes/New Zealand
+(31) 345 587 587 +(1) 678 393 0653 +(61) 2 9421 8000 +(64) 9 573 1620
www.ameron-bv.com www.ameroncoatings.com www.ameron.com.au www.ameron.co.nz