Manual de Instrucciones KBTZ2

Download as pdf or txt
Download as pdf or txt
You are on page 1of 1

KB-TZ2

KB-TZ2 SS304
KB-TZ2 SS316
2274242 A1-05.2021
hnom tfix 1c 90° 2
hef Tinst
dbit d0 TE-CD
h0 TE-YD
dh WS

1a 1d h1 = hnom 90°
d0 = ⌀ 90° d0
3a 3b
Tinst
1b 90°
6 bar/
90°

d0 = ⌀ 90 psi SI AT-A22
SIW 6AT-A22**
90 psi
6 bar/

Anchor Diameter [inch]


90°

Symbol Setting Information Units ¼ ⅜ ½ ⅝ ¾ 1


HDB Hollow Drill Bit – – – ✔ ✔ ✔ ✔
h1 = hnom
d0 = ⌀

DRS Dust Removal Systems – ✔ ✔ ✔ ✔ ✔ ✔


AT-System Adaptive Torque System** – – ✔ ✔ ✔ – –
d0

Diamond Core Bit – – ✔ ✔ ✔ ✔ ✔


d0 Drill Bit Diameter [inch] ¼ ⅜ ½ ⅝ ¾ 1
hef Effective Embedment Depth [inch] 1½ 1½ 2 2½ 2 2½ 3¼ 2¾ 3¼ 4 3¼ 3¾ 4¾ 4 5¾
hnom Nominal Embedment Depth [inch] 1¾ 1⅞ 2½ 3 2½ 3 3¾ 3¾ 4½ 4 4½ 5½ 4⅝ 6⅜
h0 Minimum Hole Depth in Base Material [inch] 2 2 2¾ 3¼ 2¾ 3¼ 4¼ 3¾ 4¼ 4¾ 4¼ 4¾ 5¾ 5 6¾
Installation Torque carbon steel [ft-lb] 4 30 50 40 110 185
Tinst, concrete
Concrete SS304, SS316 [ft-lb] 6 30 40 60 125 185
T inst, Installation Torque carbon steel [ft-lb] 4 15 25 30 50 –
grout filled CMU Grout-Filled CMU SS304, SS316 [ft-lb] 6 15 25 35 50 –
dh Fixture Hole Diameter [inch] ⁄
5 16 ⁄
7 16 ⁄
9 16 ⁄
11 16 ⁄
13 16 1⅛
7⁄16 9⁄16
WS Wrench Size [inch] 34 ⁄ 15⁄16 1⅛ 1½
Use only carbide-tipped masonry drill bits complying with ANSI B212.15.1994
* For steps 1a or 1b, make sure to drill deep enough to achieve h0, taking into account the depth of debris remaining in the hole.
** AT-System not applicable for grout-filled CMU and wood fastening applications.
For UL Listing, the ⅝" anchor is rated up to 10 NPS at a minimum of 3-¼" nominal embedment. UL Listing does not cover the ¼" anchor size.

You might also like