SiC632, SiC632A

www.vishay.com
Vishay Siliconix
50 A VRPower® Integrated Power Stage
DESCRIPTION FEATURES
The SiC632 and SiC632A are integrated power stage • Thermally enhanced PowerPAK® MLP55-31L
solutions optimized for synchronous buck applications to package
offer high current, high efficiency, and high power density • Vishay’s Gen IV MOSFET technology and a low
performance. Packaged in Vishay’s proprietary 5 mm x 5 mm side MOSFET with integrated Schottky diode
MLP package, SiC632 and SiC632A enables voltage • Delivers up to 50 A continuous current
regulator designs to deliver up to 50 A continuous current
• High efficiency performance
per phase.
• High frequency operation up to 1.5 MHz
The internal power MOSFETs utilizes Vishay’s
state-of-the-art Gen IV TrenchFET® technology that delivers • Power MOSFETs optimized for 19 V input stage
industry benchmark performance to significantly reduce • 3.3 V (SiC632A), 5 V (SiC632) PWM logic with tri-state and
switching and conduction losses. hold-off
The SiC632 and SiC632A incorporate an advanced • Zero current detect control for light load efficiency
MOSFET gate driver IC that features high current driving improvement
capability, adaptive dead-time control, an integrated • Low PWM propagation delay (< 20 ns)
bootstrap Schottky diode, a thermal warning (THWn) that
• Faster disable
alerts the system of excessive junction temperature, and
zero current detection to improve light load efficiency. The • Thermal monitor flag
drivers are also compatible with a wide range of PWM • Under voltage lockout for VCIN
controllers and supports tri-state PWM, 3.3 V (SiC632A), 5 V • Material categorization: for definitions of compliance
(SiC632) PWM logic. please see www.vishay.com/doc?99912

APPLICATIONS
• Multi-phase VRDs for computing, graphics card and
memory
• Intel IMVP-8 VRPower delivery
- VCORE, VGRAPHICS, VSYSTEM AGENT Skylake, Kabylake
platforms
- VCCGI for Apollo Lake platforms
• Up to 24 V rail input DC/DC VR modules

TYPICAL APPLICATION DIAGRAM

5V VIN
VDRV

V IN

BOOT

VCIN PHASE

ZCD_EN#
VSWH
DSBL# Gate VOUT
PWM
controller PWM driver
THWn
C GND

GL

PGND

Fig. 1 - SiC632 and SiC632A Typical Application Diagram

S20-0486-Rev. E, 29-Jun-2020 1 Document Number: 62992

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 SiC632, SiC632A
www.vishay.com
Vishay Siliconix
PINOUT CONFIGURATION

DSBL#

DSBL#
THWn

THWn
VSWH
VSWH
VSWH
PGND

VSWH
VSWH
VSWH
VDRV

PGND
VDRV
GL

GL
33
31 30 29 28 27 26 25 24 GL 24 25 26 27 28 29 30 31

PWM 1 23 VSWH VSWH 23 1 PWM

GL GL
ZCD_EN# 2 22 VSWH VSWH 22 2 ZCD_EN#
CGND 32
VCIN 3 21 VSWH VSWH 21 CGND 3 VCIN
CGND 4 20 VSWH VSWH 20 4 CGND
BOOT 5 PGND 19 VSWH VSWH 19 35 5 BOOT
PGND
N.C. 6 18 VSWH VSWH 18 6 N.C.
VIN 34
PHASE 7 17 VSWH VSWH 17 7 PHASE
VIN
VIN 8 16 VSWH VSWH 16 8 VIN

9 10 11 12 13 14 15 15 14 13 12 11 10 9

PGND
PGND
PGND
PGND
PGND
PGND
PGND
PGND
VIN
VIN
VIN

VIN
VIN
VIN
Top view Bottom view

Fig. 2 - SiC632 and SiC632A Pin Configuration

PIN CONFIGURATION
PIN NUMBER NAME FUNCTION
1 PWM PWM input logic
2 ZCD_EN# ZCD control. Active low
3 VCIN Supply voltage for internal logic circuitry
4, 32 CGND Signal ground
5 BOOT High side driver bootstrap voltage
6 N.C. Not connected internally, can be left floating or connected to ground
7 PHASE Return path of high side gate driver
8 to 11, 34 VIN Power stage input voltage. Drain of high side MOSFET
12 to 15, 28, 35 PGND Power ground
16 to 26 VSWH Phase node of the power stage
27, 33 GL Low side MOSFET gate signal
29 VDRV Supply voltage for internal gate driver
30 THWn Thermal warning open drain output
31 DSBL# Disable pin. Active low

ORDERING INFORMATION
PART NUMBER PACKAGE MARKING CODE OPTION
SiC632CD-T1-GE3 PowerPAK MLP55-31L SiC632 5 V PWM optimized
SiC632ACD-T1-GE3 PowerPAK MLP55-31L SiC632A 3.3 V PWM optimized
SiC632DB / SiC632ADB Reference board

S20-0486-Rev. E, 29-Jun-2020 2 Document Number: 62992

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 SiC632, SiC632A
www.vishay.com
Vishay Siliconix
PART MARKING INFORMATION

= Pin 1 Indicator

P/N = Part Number Code

P/N = Siliconix Logo

= ESD Symbol
LL
F = Assembly Factory Code

Y = Year Code
FYWW
WW = Week Code

LL = Lot Code

ABSOLUTE MAXIMUM RATINGS

ELECTRICAL PARAMETER CONDITIONS LIMIT UNIT
Input voltage VIN -0.3 to +28
Control logic supply voltage VCIN -0.3 to +7
Drive supply voltage VDRV -0.3 to +7
Switch node (DC voltage) -0.3 to +28
VSWH
Switch node (AC voltage) (1) -7 to +33
BOOT voltage (DC voltage) 35 V
VBOOT
BOOT voltage (AC voltage) (2) 40
BOOT to PHASE (DC voltage) -0.3 to +7
VBOOT-PHASE
BOOT to PHASE (AC voltage) (3) -0.3 to +8
All logic inputs and outputs
-0.3 to VCIN + 0.3
(PWM, DSBL#, and THWn)
Max. operating junction temperature TJ 150
Ambient temperature TA -40 to +125 °C
Storage temperature Tstg -65 to +150
Human body model, JESD22-A114 3000
Electrostatic discharge protection V
Charged device model, JESD22-C101 1000
Notes
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the
specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability
(1) The specification values indicated “AC” is V
SWH to PGND -8 V (< 20 ns, 10 μJ), min. and 33 V (< 50 ns), max.
(2) The specification value indicates “AC voltage” is V
BOOT to PGND, 40 V (< 50 ns) max.
(3) The specification value indicates “AC voltage” is V
BOOT to VPHASE, 8 V (< 20 ns) max.

RECOMMENDED OPERATING RANGE

ELECTRICAL PARAMETER MINIMUM TYPICAL MAXIMUM UNIT
Input voltage (VIN) 4.5 - 24
Drive supply voltage (VDRV) 4.5 5 5.5
V
Control logic supply voltage (VCIN) 4.5 5 5.5
BOOT to PHASE (VBOOT-PHASE, DC voltage) 4 4.5 5.5
Thermal resistance from junction to ambient - 10.6 -
°C/W
Thermal resistance from junction to case - 1.6 -

S20-0486-Rev. E, 29-Jun-2020 3 Document Number: 62992

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 SiC632, SiC632A
www.vishay.com
Vishay Siliconix

ELECTRICAL SPECIFICATIONS
(DSBL# = ZCD_EN# = 5 V, VIN = 12 V, VDRV and VCIN = 5 V, TA = 25 °C)
LIMITS
PARAMETER SYMBOL TEST CONDITION UNIT
MIN. TYP. MAX.
POWER SUPPLY
VDSBL# = 0 V, no switching, VPWM = FLOAT - 10 -
Control logic supply current IVCIN VDSBL# = 5 V, no switching, VPWM = FLOAT - 300 - μA
VDSBL# = 5 V, fS = 300 kHz, D = 0.1 - 525 -
fS = 300 kHz, D = 0.1 - 10 15
mA
fS = 1 MHz, D = 0.1 - 35 -
Drive supply current IVDRV
VDSBL# = 0 V, no switching - 15 -
μA
VDSBL# = 5 V, no switching - 55 -
BOOTSTRAP SUPPLY
Bootstrap diode forward voltage VF IF = 2 mA 0.4 V
PWM CONTROL INPUT (SiC632)
Rising threshold VTH_PWM_R 3.4 3.8 4.2
Falling threshold VTH_PWM_F 0.72 0.9 1.1
Tri-state voltage VTRI VPWM = FLOAT - 2.3 - V
Tri-state rising threshold VTRI_TH_R 0.9 1.15 1.38
Tri-state falling threshold VTRI_TH_F 3 3.3 3.6
Tri-state rising threshold hysteresis VHYS_TRI_R - 225 -
mV
Tri-state falling threshold hysteresis VHYS_TRI_F - 325 -
VPWM = 5 V - - 350
PWM input current IPWM μA
VPWM = 0 V - - -350
PWM CONTROL INPUT (SiC632A)
Rising threshold VTH_PWM_R 2.3 2.45 2.7
Falling threshold VTH_PWM_F 0.72 0.9 1.1
Tri-state Voltage VTRI VPWM = FLOAT - 1.8 - V
Tri-state rising threshold VTRI_TH_R 0.9 1.15 1.38
Tri-state falling threshold VTRI_TH_F 1.95 2.2 2.45
Tri-state rising threshold hysteresis VHYS_TRI_R - 250 -
mV
Tri-state falling threshold hysteresis VHYS_TRI_F - 300 -
VPWM = 3.3 V - - 225
PWM input current IPWM μA
VPWM = 0 V - - -225
TIMING SPECIFICATIONS
Tri-state to GH/GL rising
tPD_TRI_R - 30 -
propagation delay
Tri-state hold-off time tTSHO - 130 -
GH - turn off propagation delay tPD_OFF_GH - 15 -
GH - turn on propagation delay No load, see Fig. 4
tPD_ON_GH - 10 -
(dead time rising)
ns
GL - turn off propagation delay tPD_OFF_GL - 13 -
GL - turn on propagation delay
tPD_ON_GL - 10 -
(dead time falling)
DSBL# Lo to GH/GL falling
tPD_DSBL#_F Fig. 5 - 15 -
propagation delay
PWM minimum on-time tPWM_ON_MIN 30 - -

S20-0486-Rev. E, 29-Jun-2020 4 Document Number: 62992

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 SiC632, SiC632A
www.vishay.com
Vishay Siliconix

ELECTRICAL SPECIFICATIONS
(DSBL# = ZCD_EN# = 5 V, VIN = 12 V, VDRV and VCIN = 5 V, TA = 25 °C)
LIMITS
PARAMETER SYMBOL TEST CONDITION UNIT
MIN. TYP. MAX.
DSBL# ZCD_EN# INPUT
VIH_DSBL# Input logic high 2 - -
DSBL# logic input voltage
VIL_DSBL# Input logic low - - 0.8
V
VIH_ZCD_EN# Input logic high 2 - -
ZCD_EN# logic input voltage
VIL_ZCD_EN# Input logic low - - 0.8
PROTECTION
VCIN rising, on threshold - 3.7 4.1
Under voltage lockout VUVLO V
VCIN falling, off threshold 2.7 3.1 -
Under voltage lockout hysteresis VUVLO_HYST - 575 - mV
THWn flag set (2) TTHWn_SET - 160 -
THWn flag clear (2) TTHWn_CLEAR - 135 - °C
THWn flag hysteresis (2) TTHWn_HYST - 25 -
THWn output low VOL_THWn ITHWn = 2 mA - 0.02 - V
Notes
(1) Typical limits are established by characterization and are not production tested
(2) Guaranteed by design

DETAILED OPERATIONAL DESCRIPTION

PWM Input with Tri-State Function Diode Emulation Mode (ZCD_EN#)
The PWM input receives the PWM control signal from the VR When ZCD_EN# pin is driven below VIL_ZCD_EN#. diode
controller IC. The PWM input is designed to be compatible emulation mode is enabled. If the PWM signal switches
with standard controllers using two state logic (H and L) and below VTH_PWM_F then the LS MOSFET is under control of
advanced controllers that incorporate tri-state logic (H, L the ZCD (zero crossing detect) comparator. If, after the
and tri-state) on the PWM output. For two state logic, the internal blanking delay, the inductor current becomes less
PWM input operates as follows. When PWM is driven above than or = 0 the low side is turned off. Light load efficiency is
VPWM_TH_R the low side is turned off and the high side is improved by avoiding discharge of output capacitors. If both
turned on. When PWM input is driven below VPWM_TH_F the high side and low side MOSFETs are required to be turned
high side is turned off and the low side is turned on. For off, regardless of inductor current, the PWM input should be
tri-state logic, the PWM input operates as previously stated tri-stated.
for driving the MOSFETs when PWM is logic high and logic
Thermal Shutdown Warning (THWn)
low. However, there is a third state that is entered as the
PWM output of tri-state compatible controller enters its high The THWn pin is an open drain signal that flags the presence
impedance state during shutdown. The high impedance of excessive junction temperature. Connect with a
state of the controller’s PWM output allows the SiC632 and maximum of 20 k, to VCIN. An internal temperature sensor
SiC632A to pull the PWM input into the tri-state region (see detects the junction temperature. The temperature
definition of PWM logic and tri-state, Fig. 4). If the PWM threshold is 160 °C. When this junction temperature is
input stays in this region for the tri-state hold-off period, exceeded the THWn flag is set. When the junction
tTSHO, both high side and low side MOSFETs are turned temperature drops below 135 °C the device will clear the
off. The function allows the VR phase to be disabled without THWn signal. The SiC632 and SiC632A do not stop
negative output voltage swing caused by inductor ringing operation when the flag is set. The decision to shutdown
and saves a Schottky diode clamp. The PWM and tri-state must be made by an external thermal control function.
regions are separated by hysteresis to prevent false Voltage Input (VIN)
triggering. The SiC632A incorporates PWM voltage
This is the power input to the drain of the high side power
thresholds that are compatible with 3.3 V logic and the
MOSFET. This pin is connected to the high power
SiC632 thresholds are compatible with 5 V logic.
intermediate BUS rail.
Disable (DSBL#) 
In the low state, the DSBL# pin shuts down the driver IC and
disables both high side and low side MOSFETs. In this state,
standby current is minimized. If DSBL# is left unconnected,
an internal pull-down resistor will pull the pin to CGND and
shut down the IC.

S20-0486-Rev. E, 29-Jun-2020 5 Document Number: 62992

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 SiC632, SiC632A
www.vishay.com
Vishay Siliconix
Switch Node (VSWH and PHASE) Bootstrap Circuit (BOOT)
The switch node, VSWH, is the circuit power stage output. The internal bootstrap diode and an external bootstrap
This is the output applied to the power inductor and output capacitor form a charge pump that supplies voltage to the
filter to deliver the output for the buck converter. The PHASE BOOT pin. An integrated bootstrap diode is incorporated so
pin is internally connected to the switch node VSWH. This pin that only an external capacitor is necessary to complete the
is to be used exclusively as the return pin for the BOOT bootstrap circuit. Connect a boot strap capacitor with one
capacitor. A 20 k resistor is connected between GH leg tied to BOOT pin and the other tied to PHASE pin.
(the high side gate) and PHASE to provide a discharge path
Shoot-Through Protection and Adaptive Dead Time
for the HS MOSFET in the event that VCIN goes to zero while
VIN is still applied. The SiC632 and SiC632A have an internal adaptive logic to
avoid shoot through and optimize dead time. The shoot
Ground Connections (CGND and PGND) through protection ensures that both high side and low side
PGND (power ground) should be externally connected MOSFETs are not turned on at the same time. The adaptive
to CGND (signal ground). The layout of the printed circuit dead time control operates as follows. The high side and low
board should be such that the inductance separating CGND side gate voltages are monitored to prevent the MOSFET
and PGND is minimized. Transient differences due to turning on from tuning on until the other MOSFET's gate
inductance effects between these two pins should not voltage is sufficiently low (< 1 V). Built in delays also ensure
exceed 0.5 V that one power MOSFET is completely off, before the other
can be turned ON. This feature helps to adjust dead time as
Control and Drive Supply Voltage Input (VDRV, VCIN)
gate transitions change with respect to output current and
VCIN is the bias supply for the gate drive control IC. VDRV is temperature.
the bias supply for the gate drivers. It is recommended to
separate these pins through a resistor. This creates a low Under Voltage Lockout (UVLO)
pass filtering effect to avoid coupling of high frequency gate During the start up cycle, the UVLO disables the gate
drive noise into the IC. drive holding high side and low side MOSFET gates low
until the supply voltage rail has reached a point at which
the logic circuitry can be safely activated. The SiC632,
SiC632A also incorporates logic to clamp the gate drive
signals to zero when the UVLO falling edge triggers the
shutdown of the device. As an added precaution, a 20 k
resistor is connected between GH (the high side gate) and
PHASE to provide a discharge path for the HS MOSFET.

FUNCTIONAL BLOCK DIAGRAM
THWn BOOT V IN

VDRV
Thermal monitor
& warning

VCIN UVLO

DISB#
VCIN
- 20K
+ PHASE
PWM logic Anti-cross Vref = 1 V
control & conduction GL
PWM state control VSWH
machine logic -
+
Vref = 1 V
VDRV

CGND

VSWH
PGND

ZCD_EN# GL PGND

Fig. 3 - SiC632 and SiC632A Functional Block Diagram

S20-0486-Rev. E, 29-Jun-2020 6 Document Number: 62992

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 SiC632, SiC632A
www.vishay.com
Vishay Siliconix

DEVICE TRUTH TABLE

DSBL# ZCD_EN# PWM GH GL
Open X X L L
L X X L L
H, IL > 0 A
H L L L
L, IL < 0 A
H L H H L
H L Tri-state L L
H H L L H
H H H H L
H H Tri-state L L

PWM TIMING DIAGRAM

VTH_PWM_R
VTH_TRI_F
VTH_TRI_R
VTH_PWM_F
PWM
t PD_OFF_GL
t TSHO

GL
t PD_ON_GL
t PD_TRI_R

t TSHO
t PD_ON_GH t PD_OFF_GH

t PD_TRI_R

GH

Fig. 4 - Definition of PWM Logic and Tri-state

DSBL# PROPAGATION DELAY

PWM PWM

DSBL# Disable DSBL#

GH GH

GL GL

t t

DSBL#Low to GH Falling Propagation Delay DSBL# Low to GL Falling Propagation Delay

Fig. 5 - DSBL# Falling Propagation Delay

S20-0486-Rev. E, 29-Jun-2020 7 Document Number: 62992

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 SiC632, SiC632A
www.vishay.com
Vishay Siliconix
ELECTRICAL CHARACTERISTICS
Test condition: VIN = 13 V, DSBL# = VDRV = VCIN = 5 V, ZCD_EN# = 5 V, VOUT = 1 V, LOUT = 250 nH (DCR = 0.32 m), TA = 25 °C,
natural convection cooling (All power loss and normalized power loss curves show SiC632 and SiC632A losses only unless otherwise stated)

94 55

90 50

86 45
500 kHz
500 kHz

Output Current, IOUT (A)

750 kHz
82 40
Efficiency (%)

1 MHz
1 MHz
78 35

74 30

70 25
Complete converter efficiency
66 PIN = [(VIN x IIN) + 5 V x (IVDRV + IVCIN)] 20
POUT = VOUT x IOUT, measured at output capacitor
62 15
0 5 10 15 20 25 30 35 40 45 50 0 15 30 45 60 75 90 105 120 135 150
Output Current, IOUT (A) PCB Temperature, TPCB (°C)
Fig. 6 - Efficiency vs. Output Current (VIN = 12.6 V) Fig. 9 - Safe Operating Area

5.0 16.0
IOUT = 25A
4.5 14.0
Power Loss, PL (W)

4.0 12.0
Power Loss, PL (W)

3.5 10.0
1 MHz

3.0 8.0

2.5 6.0 750 kHz

2.0 4.0

1.5 2.0 500 kHz

1.0 0.0
200 300 400 500 600 700 800 900 1000 1100 0 5 10 15 20 25 30 35 40 45
Switching Frequency, fs (KHz) Output Current, IOUT (A)
Fig. 7 - Power Loss vs. Switching Frequency (VIN = 12.6 V) Fig. 10 - Power Loss vs. Output Current (VIN = 12.6 V)

98 94
500 kHz
500 kHz
94 90

90
86
Efficiency (%)

86
82
Efficiency (%)

82 750 kHz 750 kHz

1 MHz 78 1 MHz
78
74
74
70
70
Complete converter efficiency Complete converter efficiency
PIN = [(VIN x IIN) + 5 V x (IVDRV + IVCIN)] 66 PIN = [(VIN x IIN) + 5 V x (IVDRV + IVCIN)]
66
POUT = VOUT x IOUT, measured at output capacitor POUT = VOUT x IOUT, measured at output capacitor
62 62
0 5 10 15 20 25 30 35 40 45 50 0 5 10 15 20 25 30 35 40 45 50
Output Current, IOUT (A) Output Current, IOUT (A)

Fig. 8 - Efficiency vs. Output Current (VIN = 9 V) Fig. 11 - Efficiency vs. Output Current (VIN = 19 V)

S20-0486-Rev. E, 29-Jun-2020 8 Document Number: 62992

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 SiC632, SiC632A
www.vishay.com
Vishay Siliconix
ELECTRICAL CHARACTERISTICS
Test condition: VIN = 13 V, DSBL# = VDRV = VCIN = 5 V, ZCD_EN# = 5 V, VOUT = 1 V, LOUT = 250 nH (DCR = 0.32 m), TA = 25 °C,
natural convection cooling (All power loss and normalized power loss curves show SiC632 and SiC632A losses only unless otherwise stated)

4.2 0.40

4.0 0.35
IF = 2 mA

BOOT Diode Forward Voltage, VF (V)

Control Logic Supply Voltage, VCIN (V)

3.8 VUVLO_RISING 0.30

3.6 0.25

3.4 0.20

3.2 0.15

3.0 VUVLO_FALLING 0.10

2.8 0.05

2.6 0.00
-60 -40 -20 0 20 40 60 80 100 120 140 -60 -40 -20 0 20 40 60 80 100 120 140
Temperature (°C) Temperature (°C)
Fig. 12 - UVLO Threshold vs. Temperature Fig. 15 - Boot Diode Forward Voltage vs. Temperature

3.20 3.20

2.85 2.85
Control Logic Supply Voltage, VPWM (V)

PWM Threshold Voltage, VPWM (V)

VTH_PWM_R
VTH_PWM_R
2.50 2.50
VTRI_TH_F
VTRI_TH_F
2.15 2.15

1.80 1.80
VTRI VTRI
1.45 VTRI_TH_R 1.45
VTRI_TH_R
1.10 1.10

0.75 VTH_PWM_F 0.75

VTH_PWM_F

0.40 0.40
-60 -40 -20 0 20 40 60 80 100 120 140 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5
Temperature (°C) Driver Supply Voltage, VCIN (V)
Fig. 13 - PWM Threshold vs. Temperature (SiC632A) Fig. 16 - PWM Threshold vs. Driver Supply Voltage (SiC632A)

5.0 5.00

4.5 4.50 VTH_PWM_R

PWM Threshold Voltage, VPWM (V)

VTH_PWM_R
4.0 4.00
Control Logic Supply Voltage, VPWM (V)

3.5 3.50
VTRI_TH_F
3.0 VTRI_TH_F 3.00
VTRI VTRI
2.5 2.50

2.0 2.00

1.5 VTRI_TH_R 1.50 VTRI_TH_R

1.0 1.00
VTH_PWM_F VTH_PWM_F
0.5 0.50

0.0 0
-60 -40 -20 0 20 40 60 80 100 120 140 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5
Temperature (°C) Driver Supply Voltage, VCIN (V)

Fig. 14 - PWM Threshold vs. Temperature (SiC632) Fig. 17 - PWM Threshold vs. Driver Supply Voltage (SiC632)

S20-0486-Rev. E, 29-Jun-2020 9 Document Number: 62992

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 SiC632, SiC632A
www.vishay.com
Vishay Siliconix
ELECTRICAL CHARACTERISTICS
Test condition: VIN = 13 V, DSBL# = VDRV = VCIN = 5 V, ZCD_EN# = 5 V, VOUT = 1 V, LOUT = 250 nH (DCR = 0.32 m), TA = 25 °C,
natural convection cooling (All power loss and normalized power loss curves show SiC632 and SiC632A losses only unless otherwise stated)

1.7 2.20

1.6 VIH_DSBL# 2.00

DSBL# Threshold Voltage, VDSBL# (V)

ZCD_EN# Threshold Voltage, VZCD_EN# (V)

1.5 1.80
VIH_ZCD_EN#_R
1.4 1.60

1.3 1.40

1.2 1.20

1.1 1.00 VIL_ZCD_EN#_F

1.0 VIL_DSBL# 0.80

0.9 0.60
-60 -40 -20 0 20 40 60 80 100 120 140 4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5
Temperature (°C) Driver Supply Voltage, VCIN (V)
Fig. 18 - DSBL# Threshold vs. Temperature Fig. 21 - ZCD_EN# Threshold vs. Driver Supply Voltage

1.7 80

1.6 VIH_DSBL# 70
DSBL# Threshold Voltage, VDSBL# (V)

VDSBL# = 0 V
Driver Supply Current, IVDVR & IVCIN (V)

1.5 60

1.4 50

1.3 40

1.2 30

1.1 20
VIL_DSBL#
1.0 10

0.9 0
4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5 -60 -40 -20 0 20 40 60 80 100 120 140
Driver Supply Voltage, VCIN (V) Temperature (°C)

Fig. 19 - DSBL# vs. Driver Input Voltage Fig. 22 - Driver Shutdown Current vs. Temperature

10.8 390

10.7 380
DSBL# Pull-Down Current, IDSBL# (uA)

Driver Supply Current, IVDVR & IVCIN (V)

10.6 370

10.5 360

10.4 350 VPWM = FLOAT

10.3 340

10.2 330

10.1 320

10.0 310
-60 -40 -20 0 20 40 60 80 100 120 140 -60 -40 -20 0 20 40 60 80 100 120 140
Temperature (°C) Temperature (°C)

Fig. 20 - DSBL# Pull-Down Current vs. Temperature Fig. 23 - Driver Supply Current vs. Temperature

S20-0486-Rev. E, 29-Jun-2020 10 Document Number: 62992

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 SiC632, SiC632A
www.vishay.com
Vishay Siliconix
PCB LAYOUT RECOMMENDATIONS
Step 1: VIN/GND Planes and Decoupling Step 3: VCIN/VDRV Input Filter

VSWH

CVDRV
P
G
N
D
PGND
VIN CVCIN
CGND

VIN plane
PGND plane

1. Layout VIN and PGND planes as shown above 1. The VCIN/VDRV input filter ceramic cap should be placed
2. Ceramic capacitors should be placed right between VIN very close to IC. It is recommended to connect two caps
and PGND, and very close to the device for best separately
decoupling effect 2. CVCIN cap should be placed between pin 3 and pin 4
3. Difference values / packages of ceramic capacitors (CGND of driver IC) to achieve best noise filtering
should be used to cover entire decoupling spectrum e.g. 3. CVDRV cap should be placed between pin 28 (PGND of
1210, 0805, 0603, and 0402 driver IC) and pin 29 to provide maximum instantaneous
4. Smaller capacitance value, closer to device VIN pin(s) driver current for low side MOSFET during switching
- better high frequency noise absorbing cycle
Step 2: VSWH Plane 4. For connecting CVCIN analog ground, it is recommended
to use large plane to reduce parasitic inductance
Step 4: BOOT Resistor and Capacitor Placement
VVSWH
SWH
Snubber

Cboot

Rboot

PPGND
GND plane
Plane

1. Connect output inductor to DrMOS with large plane to

lower the resistance 1. These components need to be placed very close to IC,
2. If any snubber network is required, place the right between PHASE (pin 7) and BOOT (pin 5)
components as shown above and the network can be 2. To reduce parasitic inductance, chip size 0402 can be
placed at bottom used

S20-0486-Rev. E, 29-Jun-2020 11 Document Number: 62992

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 SiC632, SiC632A
www.vishay.com
Vishay Siliconix
Step 5: Signal Routing
1. Thermal relief vias can be added on the VIN and PGND
CGND pads to utilize inner layers for high current and thermal
dissipation
CGND 2. To achieve better thermal performance, additional vias
can be put on VIN plane and PGND plane
3. VSWH pad is a noise source and not recommended to put
vias on this plane
4. 8 mil drill for pads and 10 mils drill for plane can be the
optional via size. Vias on pad may drain solder during
assembly and cause assembly issue. Please consult
with the assembly house for guideline

Step 7: Ground Connection
PGND CGND

VSWH

1. Route the PWM / ZCD_EN# / DSBL# / THWn signal

traces out of the top left corner next DrMOS pin 1
2. PWM signal is very important signal, both signal and PGND

return traces need to pay special attention of not letting

this trace cross any power nodes on any layer
3. It is best to “shield” traces form power switching nodes,
e.g. VSWH, to improve signal integrity
4. GL (pin 27) has been connected with GL pad internally
and does not need to connect externally

Step 6: Adding Thermal Relief Vias 1. It is recommended to make single connection between
CGND and PGND and this connection can be done on top
layer
2. It is recommended to make the whole inner 1 layer (next
to top layer) ground plane and separate them into CGND
and PGND plane
VSWH 3. These ground planes provide shielding between noise
source on top layer and signal trace on bottom layer

CGND

PGND

VIN
PGND
plane

VIN plane







S20-0486-Rev. E, 29-Jun-2020 12 Document Number: 62992

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 SiC632, SiC632A
www.vishay.com
Vishay Siliconix
Multi-Phases VRPower PCB Layout
Following is an example for 6 phase layout. As can be seen, all the VRPower stages are lined in X-direction compactly with
decoupling caps next to them. The inductors are placed as close as possible to the SiC632 and SiC632A to minimize the PCB
copper loss. Vias are applied on all PADs (VIN, PGND, CGND) of the SiC632 and SiC632A to ensure that both electrical and thermal
performance are excellent. Large copper planes are used for all the high current loops, such as VIN, VSWH, VOUT and PGND. These
copper planes are duplicated in other layers to minimize the inductance and resistance. All the control signals are routed from
the SiC632 and SiC632A to a controller placed to the north of the power stage through inner layers to avoid the overlap of high
current loops. This achieves a compact design with the output from the inductors feeding a load located to the south of the
design as shown in the figure.

VIN

PGND

VOUT

Fig. 24 - Multi - Phase VRPower Layout Top View

VIN

PGND

VOUT

Fig. 25 - Multi - Phase VRPower Layout Bottom View

S20-0486-Rev. E, 29-Jun-2020 13 Document Number: 62992

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 SiC632, SiC632A
www.vishay.com
Vishay Siliconix

PRODUCT SUMMARY
Part number SiC632 SiC632A
50 A power stage, 4.5 VIN to 24 VIN, 5 V PWM 50 A power stage, 4.5 VIN to 24 VIN, 3.3 V
Description
with ZCD mode PWM with ZCD mode
Input voltage min. (V) 4.5 4.5
Input voltage max. (V) 24 24
Continuous current rating max. (A) 50 50
Switch frequency max. (kHz) 1500 1500
Enable (yes / no) Yes Yes
Monitoring features - -
Protection UVLO, THDN UVLO, THDN
Light load mode ZCD ZCD
Pulse-width modulation (V) 5 3.3
Package type PowerPAK MLP55-31L PowerPAK MLP55-31L
Package size (W, L, H) (mm) 5.0 x 5.0 x 0.75 5.0 x 5.0 x 0.75
Status code 2 2
Product type VRPower (DrMOS) VRPower (DrMOS)
Applications Computer, industrial, networking Computer, industrial, networking

Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon
Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package / tape drawings, part marking, and
reliability data, see www.vishay.com/ppg?62992.

S20-0486-Rev. E, 29-Jun-2020 14 Document Number: 62992

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 Package Information
www.vishay.com
Vishay Siliconix
PowerPAK® MLP55-31L Case Outline

5 6 0.10 C 0.08 C D2-5 K12 K13

Pin 1 dot A K7
2x K1 D2- 1 8x
by marking 0.10 C A A1
A
D K4

F2
2x D2-4

F1
A2

K8
0.10 C B 24 31

E2-4

K11
23 1

K5 E2- 1
F3

0.10 M C A B

K6
K3

K10
MLP55-31L

0.05 M C
(5 mm x 5 mm) e1/3x
E

E2- 3

E2- 2
e/25x

3
b 16 8
B 31x

L
b1
31x 15 9
K2
C D2- 3 D2- 2
K9
e2 e3

Top view Side view Bottom view

MILLIMETERS INCHES
DIM.
MIN. NOM. MAX. MIN. NOM. MAX.
A 0.70 0.75 0.80 0.027 0.029 0.031
A1 0.00 - 0.05 0.000 - 0.002
A2 0.20 ref. 0.008 ref.
b 0.20 0.25 0.30 0.078 0.098 0.011
b1 0.15 0.20 0.25 0.006 0.008 0.010
D 4.90 5.00 5.10 0.193 0.196 0.200
e 0.50 BSC 0.019 BSC
e1 3.50 BSC 0.138 BSC
e2 1.50 BSC 0.060 BSC
e3 1.00 BSC 0.040 BSC
E 4.90 5.00 5.10 0.193 0.196 0.200
L 0.35 0.40 0.45 0.013 0.015 0.017
D2-1 0.98 1.03 1.08 0.039 0.041 0.043
D2-2 0.98 1.03 1.08 0.039 0.041 0.043
D2-3 1.87 1.92 1.97 0.074 0.076 0.078
D2-4 0.30 BSC 0.012 BSC
D2-5 1.05 1.10 1.15 0.041 0.043 0.045
E2-1 1.27 1.32 1.37 0.050 0.052 0.054
E2-2 1.93 1.98 2.03 0.076 0.078 0.080
E2-3 3.75 3.80 3.85 0.148 0.150 0.152
E2-4 0.45 BSC 0.018 BSC
F1 0.15 0.20 0.25 0.006 0.008 0.010
F2 0.20 ref. 0.008 ref.
F3 0.15 ref. 0.006 ref.

Revision: 21-Aug-17 1 Document Number: 64909

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 Package Information
www.vishay.com
Vishay Siliconix
MILLIMETERS INCHES
DIM.
MIN. NOM. MAX. MIN. NOM. MAX.
K1 0.67 BSC 0.026 BSC
K2 0.22 BSC 0.008 BSC
K3 1.25 BSC 0.049 BSC
K4 0.10 BSC 0.004 BSC
K5 0.38 BSC 0.015 BSC
K6 0.12 BSC 0.005 BSC
K7 0.40 BSC 0.016 BSC
K8 0.40 BSC 0.016 BSC
K9 0.40 BSC 0.016 BSC
K10 0.85 BSC 0.033 BSC
K11 0.40 BSC 0.016 BSC
K12 0.40 BSC 0.016 BSC
K13 0.75 BSC 0.030 BSC
ECN: T17-0423-Rev. F, 21-Aug-17
DWG: 6025

Notes
1. Use millimeters as the primary measurement
2. Dimensioning and tolerances conform to ASME Y14.5M. - 1994
3. Dimension b applies to plated terminal and is measured between 0.20 mm and 0.25 mm from terminal tip
4. The pin #1 identifier must be existed on the top surface of the package by using indentation mark or other feature of package body
5. Exact shape and size of this feature is optional
6. Package warpage max. 0.08 mm
7. Applied only for terminals

Revision: 21-Aug-17 2 Document Number: 64909

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 PAD Pattern
www.vishay.com
Vishay Siliconix
Recommended Land Pattern
PowerPAK® MLP55-31L

Top side transparent view

(not bottom view) Land pattern for MLP55-31L
(D2-4) 5

0.75
1.35 0.57

0.3
0.33
3.4
(D2-1) (D2-5) 31 0.5 1 24
31 1.03 1.05 24
0.75
1 (D3) 0.3
23 1.13
1 23

1.6
0.45
(E3)

0.85
0.3
0.5 (e)

0.35
(E2-2)

1.15

1.42
1.32

0.15

0.33
(K2) 0.22 2.02
1.75 0.3
(E2-1)

0.4
4.2

(K1) 0.67

3.5
5

3.05
0.07
0.25

2.15
(E2-3)

(b)

2.08
1.98

0.5
8 16 8 0.35 0.18 16

0.58

0.65
(L) 9 15 (L) 0.3
0.4 (D2-2) (D2-3) 0.4 9 15
0.35

0.3
1.03 1.92 0.35 0.5 0.75
0.5 0.65

All dimensions in millimeters

31 24

1 23
33
Component for MLP55-31L
32

35 Land pattern for MLP55-31L

33

8 16

9 15

Revision: 18-Oct-2019 1 Document Number: 66944

For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer

ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited
to the warranty expressed therein.

Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website
or for that of subsequent links.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

© 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED

Revision: 09-Jul-2021 1 Document Number: 91000