Scribd
Upload
66 views30 pages

7 Segment Display

The document describes code for controlling a 7-segment display, buzzer, DHT11 temperature and humidity sensor, RGB LED, LDR light sensor, and keypad lock system. It includes functions for defining the pins for a 7-segment display, displaying numbers on the display, playing tones on a buzzer, reading temperature and humidity from a DHT11 sensor, changing the color of an RGB LED, turning on an LED based on light levels from an LDR, and unlocking a servo motor with a keypad password entry.

Uploaded by

Eyedel Meh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
66 views30 pages

7 Segment Display

The document describes code for controlling a 7-segment display, buzzer, DHT11 temperature and humidity sensor, RGB LED, LDR light sensor, and keypad lock system. It includes functions for defining the pins for a 7-segment display, displaying numbers on the display, playing tones on a buzzer, reading temperature and humidity from a DHT11 sensor, changing the color of an RGB LED, turning on an LED based on light levels from an LDR, and unlocking a servo motor with a keypad password entry.

Uploaded by

Eyedel Meh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 30

7 Segment display

int disp_pin[7];

void define_segment_pins(int a, int b, int c, int d, int e, int f, int g)


{
disp_pin[0] = a;
disp_pin[1] = b;
disp_pin[2] = c;
disp_pin[3] = d;
disp_pin[4] = e;
disp_pin[5] = f;
disp_pin[6] = g;
}

void display_number(int num)


{
switch(num)
{
case 0:
digitalWrite(disp_pin[0], HIGH);
digitalWrite(disp_pin[1], HIGH);
digitalWrite(disp_pin[2], HIGH);
digitalWrite(disp_pin[3], HIGH);
digitalWrite(disp_pin[4], LOW);
digitalWrite(disp_pin[5], HIGH);
digitalWrite(disp_pin[6], HIGH);
break;
case 1:
digitalWrite(disp_pin[0], HIGH);
digitalWrite(disp_pin[1], HIGH);
digitalWrite(disp_pin[2], HIGH);
digitalWrite(disp_pin[3], HIGH);
digitalWrite(disp_pin[4], HIGH);
digitalWrite(disp_pin[5], HIGH);
digitalWrite(disp_pin[6], HIGH);
break;
case 2:
digitalWrite(disp_pin[0], HIGH);
digitalWrite(disp_pin[1], HIGH);
digitalWrite(disp_pin[2], HIGH);
digitalWrite(disp_pin[3], LOW);
digitalWrite(disp_pin[4], LOW);
digitalWrite(disp_pin[5], LOW);
digitalWrite(disp_pin[6], LOW);
break;
case 3:
digitalWrite(disp_pin[0], HIGH);
digitalWrite(disp_pin[1], LOW);
digitalWrite(disp_pin[2], HIGH);
digitalWrite(disp_pin[3], HIGH);
digitalWrite(disp_pin[4], HIGH);
digitalWrite(disp_pin[5], HIGH);
digitalWrite(disp_pin[6], HIGH);
break;
case 4:
digitalWrite(disp_pin[0], HIGH);
digitalWrite(disp_pin[1], LOW);
digitalWrite(disp_pin[2], HIGH);
digitalWrite(disp_pin[3], HIGH);
digitalWrite(disp_pin[4], LOW);
digitalWrite(disp_pin[5], HIGH);
digitalWrite(disp_pin[6], HIGH);
break;
case 5:
digitalWrite(disp_pin[0], LOW);
digitalWrite(disp_pin[1], HIGH);
digitalWrite(disp_pin[2], HIGH);
digitalWrite(disp_pin[3], LOW);
digitalWrite(disp_pin[4], LOW);
digitalWrite(disp_pin[5], HIGH);
digitalWrite(disp_pin[6], HIGH);
break;
case 6:
digitalWrite(disp_pin[0], HIGH);
digitalWrite(disp_pin[1], HIGH);
digitalWrite(disp_pin[2], HIGH);
digitalWrite(disp_pin[3], HIGH);
digitalWrite(disp_pin[4], LOW);
digitalWrite(disp_pin[5], LOW);
digitalWrite(disp_pin[6], HIGH);
break;
case 7:
digitalWrite(disp_pin[0], HIGH);
digitalWrite(disp_pin[1], HIGH);
digitalWrite(disp_pin[2], LOW);
digitalWrite(disp_pin[3], HIGH);
digitalWrite(disp_pin[4], HIGH);
digitalWrite(disp_pin[5], LOW);
digitalWrite(disp_pin[6], HIGH);
break;
case 8:
digitalWrite(disp_pin[0], LOW);
digitalWrite(disp_pin[1], HIGH);
digitalWrite(disp_pin[2], HIGH);
digitalWrite(disp_pin[3], LOW);
digitalWrite(disp_pin[4], LOW);
digitalWrite(disp_pin[5], LOW);
digitalWrite(disp_pin[6], LOW);
break;
case 9:
digitalWrite(disp_pin[0], HIGH);
digitalWrite(disp_pin[1], HIGH);
digitalWrite(disp_pin[2], HIGH);
digitalWrite(disp_pin[3], HIGH);
digitalWrite(disp_pin[4], HIGH);
digitalWrite(disp_pin[5], HIGH);
digitalWrite(disp_pin[6], LOW);
break;

default:
digitalWrite(disp_pin[0], HIGH);
digitalWrite(disp_pin[1], HIGH);
digitalWrite(disp_pin[2], HIGH);
digitalWrite(disp_pin[3], HIGH);
digitalWrite(disp_pin[4], HIGH);
digitalWrite(disp_pin[5], HIGH);
digitalWrite(disp_pin[6], LOW);
break;
}
}

void setup() {
pinMode(7, OUTPUT);
pinMode(8, OUTPUT);
pinMode(9, OUTPUT);
pinMode(10, OUTPUT);
pinMode(11, OUTPUT);
pinMode(12, OUTPUT);
pinMode(13, OUTPUT);
define_segment_pins(13,12,11,10,9,8,7); /* a-g segment pins to Arduino */
}

void loop() {
int i;
for(i = 9; i>=0; i--)
{
display_number(i);
delay(1000);
}
for(i = 0; i<=9; i++)
{
display_number(i);
delay(1000);
}
}

Buzzer(melody)
//#include "pitches.h";

#define NOTE_B0 31
#define NOTE_C1 33
#define NOTE_CS1 35
#define NOTE_D1 37
#define NOTE_DS1 39
#define NOTE_E1 41
#define NOTE_F1 44
#define NOTE_FS1 46
#define NOTE_G1 49
#define NOTE_GS1 52
#define NOTE_A1 55
#define NOTE_AS1 58
#define NOTE_B1 62
#define NOTE_C2 65
#define NOTE_CS2 69
#define NOTE_D2 73
#define NOTE_DS2 78
#define NOTE_E2 82
#define NOTE_F2 87
#define NOTE_FS2 93
#define NOTE_G2 98
#define NOTE_GS2 104
#define NOTE_A2 110
#define NOTE_AS2 117
#define NOTE_B2 123
#define NOTE_C3 131
#define NOTE_CS3 139
#define NOTE_D3 147
#define NOTE_DS3 156
#define NOTE_E3 165
#define NOTE_F3 175
#define NOTE_FS3 185
#define NOTE_G3 196
#define NOTE_GS3 208
#define NOTE_A3 220
#define NOTE_AS3 233
#define NOTE_B3 247
#define NOTE_C4 262
#define NOTE_CS4 277
#define NOTE_D4 294
#define NOTE_DS4 311
#define NOTE_E4 330
#define NOTE_F4 349
#define NOTE_FS4 370
#define NOTE_G4 392
#define NOTE_GS4 415
#define NOTE_A4 440
#define NOTE_AS4 466
#define NOTE_B4 494
#define NOTE_C5 523
#define NOTE_CS5 554
#define NOTE_D5 587
#define NOTE_DS5 622
#define NOTE_E5 659
#define NOTE_F5 698
#define NOTE_FS5 740
#define NOTE_G5 784
#define NOTE_GS5 831
#define NOTE_A5 880
#define NOTE_AS5 932
#define NOTE_B5 988
#define NOTE_C6 1047
#define NOTE_CS6 1109
#define NOTE_D6 1175
#define NOTE_DS6 1245
#define NOTE_E6 1319
#define NOTE_F6 1397
#define NOTE_FS6 1480
#define NOTE_G6 1568
#define NOTE_GS6 1661
#define NOTE_A6 1760
#define NOTE_AS6 1865
#define NOTE_B6 1976
#define NOTE_C7 2093
#define NOTE_CS7 2217
#define NOTE_D7 2349
#define NOTE_DS7 2489
#define NOTE_E7 2637
#define NOTE_F7 2794
#define NOTE_FS7 2960
#define NOTE_G7 3136
#define NOTE_GS7 3322
#define NOTE_A7 3520
#define NOTE_AS7 3729
#define NOTE_B7 3951
#define NOTE_C8 4186
#define NOTE_CS8 4435
#define NOTE_D8 4699
#define NOTE_DS8 4978

int melody[] = {

NOTE_G5, NOTE_G5, NOTE_G5, NOTE_D5,


NOTE_E5, NOTE_E5, NOTE_D5,
NOTE_B5, NOTE_B5, NOTE_A5, NOTE_A5,
NOTE_G5, NOTE_D5,
NOTE_G5, NOTE_G5, NOTE_G5, NOTE_D5,
NOTE_E5, NOTE_E5, NOTE_D5,
NOTE_B5, NOTE_B5, NOTE_A5, NOTE_A5,
NOTE_G5

};

int noteDurations[] = {
4,4,4,4,
4,4,2,
4,4,4,4,
2,4,4,
4,4,4,4,
4,4,2,
4,4,4,4,
2};

void setup(){

for (int thisNote = 0; thisNote < 26; thisNote++) {

int noteDuration = 1000/noteDurations[thisNote];


tone(8, melody[thisNote],noteDuration);
int pauseBetweenNotes = noteDuration * 1.30;
delay(pauseBetweenNotes);
noTone(8);
}

void loop(){

}
DHT11

/*
This code records the temperature through testing the mV put out by the sensor.
It records in both Celcius and Fahrenheit.
It can only detect from -40 degrees C to 125 degrees C or -40 degrees F
to 257 degrees F
The Humidity is simulated by a potentiometer by being mapped into percentages
*/
#include<LiquidCrystal.h>
LiquidCrystal lcd(2,3,4,5,6,7);
const int analogIn = A0;
int humiditysensorOutput = 0;
// Defining Variables
int RawValue= 0;
double Voltage = 0;
double tempC = 0;
double tempF = 0;

void setup(){
//Serial.begin(9600);
lcd.begin(16, 2) ;
pinMode(A1, INPUT);
}

void loop(){

RawValue = analogRead(analogIn);
Voltage = (RawValue / 1023.0) * 5000; // 5000 to get millivots.
tempC = (Voltage-500) * 0.1; // 500 is the offset
tempF = (tempC * 1.8) + 32; // convert to F
//Serial.print("Raw Value = " );
//Serial.print(RawValue);
//Serial.print("\t milli volts = ");
//Serial.print(Voltage,0); //
lcd.setCursor(0,0);
lcd.print("Temp:");
lcd.print(tempC,1);
//Serial.print("\t Temperature in F = ");
//Serial.println(tempF,1);
humiditysensorOutput = analogRead(A1);
lcd.setCursor(0,1);
lcd.print("Humidity:"); // Printing out Humidity Percentage
lcd.print(map(humiditysensorOutput, 0, 1023, 10, 70));
lcd.println("%");
delay(5000); //iterate every 5 seconds
}

RGb LED

#include<LiquidCrystal.h>
LiquidCrystal lcd(2,3,4,5,6,7);

const int buttonPin = 12;


const int redPin = 11;
const int greenPin = 9;
const int bluePin = 10;
int counter = 0;

void setup() {
lcd.begin(16, 2) ;
pinMode(buttonPin, INPUT);
pinMode(redPin, OUTPUT);
pinMode(greenPin, OUTPUT);
pinMode(bluePin, OUTPUT);
}

void loop() {
int buttonState;
buttonState = digitalRead(buttonPin);

if (buttonState == LOW) {

counter++;
delay(150);

else if (counter == 0) {
digitalWrite(redPin, LOW);
digitalWrite(greenPin, LOW);
digitalWrite(bluePin, LOW);
lcd.setCursor(0,0);
lcd.print("RGB COLOR");
}

else if (counter == 1) {
digitalWrite(redPin, HIGH);
digitalWrite(greenPin, LOW);
digitalWrite(bluePin, LOW);
lcd.setCursor(0,0);
lcd.print("Color: RED");

}
else if (counter == 2) {
digitalWrite(redPin, LOW);
digitalWrite(greenPin, HIGH);
digitalWrite(bluePin, LOW);
lcd.setCursor(0,0);
lcd.print("Color:GREEN");

else if (counter == 3) {
digitalWrite(redPin, LOW);
digitalWrite(greenPin, LOW);
digitalWrite(bluePin, HIGH);
lcd.setCursor(0,0);
lcd.print("Color: BLUE");

else {
counter = 0;
lcd.clear();
}
}
LDR

int value=0;
void setup()
{
Serial.begin(9600);
pinMode(11, OUTPUT);
pinMode(A0, INPUT);
}

void loop()

value= analogRead(A0);

if(value<10)
{
digitalWrite(11, HIGH);
Serial.println("Light ON");
Serial.println(value);
}
else
{
digitalWrite(11, LOW);
Serial.println("Light OFF");
Serial.println(value);
}
}

#include <Keypad.h>
#include <LiquidCrystal.h>
#include <Servo.h>

#define Password_Length 5

Servo myservo;
LiquidCrystal lcd(A0, A1, A2, A3, A4, A5);

int pos = 0;

char Data[Password_Length];
char Master[Password_Length] = "1234";
byte data_count = 0, master_count = 0;

bool Pass_is_good;
bool door = false;
char customKey;
int attempt = 0;

/*---preparing keypad---*/

const byte ROWS = 4;


const byte COLS = 4;
char keys[ROWS][COLS] = {
{'1', '2', '3', 'A'},
{'4', '5', '6', 'B'},
{'7', '8', '9', 'C'},
{'*', '0', '#', 'D'}
};
byte rowPins[ROWS] = {0, 1, 2, 3};
byte colPins[COLS] = {4, 5, 6, 7};

Keypad customKeypad( makeKeymap(keys),


rowPins, colPins, ROWS, COLS);

/*--- Main Action ---*/


void setup(){
myservo.attach(9, 2000, 2400);
ServoClose();
lcd.begin(16, 2);

}
void loop(){
if (door == true){
customKey = customKeypad.getKey();
if (customKey == '#') {
lcd.clear();
ServoClose();
door = false;
}
}
else
Open();
}

void clearData(){
while (data_count != 0){
Data[data_count--] = 0;
}
return;
}

void ServoClose(){
for (pos = 90; pos >= 0; pos -= 10) {
myservo.write(pos);
}
}

void ServoOpen(){
for (pos = 0; pos <= 90; pos += 10) {
myservo.write(pos);
}
}

void Open(){
lcd.setCursor(0, 0);
lcd.print("Enter Password");

customKey = customKeypad.getKey();
if (customKey){
Data[data_count] = customKey;
lcd.setCursor(data_count, 1);
lcd.print(Data[data_count]);
data_count++;
}

if (data_count == Password_Length - 1){


if (!strcmp(Data, Master)){
lcd.clear();
ServoOpen();
lcd.print("Unlock Sucessful");
door = true;
delay(5000);

ServoClose();
door = false;
}
else
{
lcd.clear();
lcd.print(" Wrong Password ");
door = false;
attempt+=1;
}
delay(1000);
lcd.clear();
clearData();
}
if(attempt == 3){
lcd.clear();
door = true;
lcd.print(" 3 attempts done ");
}
}
#define LED 9
#define pot A0

int potReading = 0;

void setup(){

Serial.begin(9600);
pinMode(LED, OUTPUT);
pinMode(pot, INPUT);
}

void loop(){

potReading = analogRead(pot);
potReading = map(potReading, 0,1023,0,255);
Serial.println(potReading);
analogWrite(LED, potReading);

#include <Servo.h>

Servo myServo;

int pos = 0;

void setup()
{

myServo.attach(9);
}

void loop()
{

for(pos = 1; pos<=179; pos+=1){


myServo.write(pos);
delay(15);

for(pos = 179; pos>1; pos-=1){


myServo.write(pos);
delay(15);

You might also like