SLR-PK – 151

Seat
No.
Set P
B.E. (Mechanical) (Part – II) (New) Examination, 2016
PLASTIC ENGINEERING (Elective – II)
Day and Date : Thursday, 12-5-2016 Max. Marks : 100
Time : 3.00 p.m. to 6.00 p.m.
Instructions : 1) Assume suitable data whenever necessary and state it clearly.
2) Attempt any 3 questions from Q. 2, Q. 3, Q. 4, Q. 5 and 3
questions from to Q. 6, Q. 7, Q. 8 Q. 9.
3) Q. No. 1 is compulsory. It should be solved in first 30 minutes
in Answer Book Page No. 3. Each question carries one mark.
4) Answer MCQ/Objective type questions on Page No. 3
only. Don’t forget to mention, Q.P. Set (P/Q/R/S) on Top of
Page.
MCQ/Objective Type Questions
Duration : 30 Minutes Marks : 20
1. Choose the correct answer : (20×1=20)
1) Generally, polymers are very in weight with significant degrees
of strength.
a) Heavy b) Light c) Both a) and b) d) None of above
2) are mixed with plastics to improve their flow characteristics
and decrease their brittleness.
a) Stabilizers b) Colorants c) Plasticizers d) Fillers
3) Plasticizers are considered solvents.
a) Volatile b) Non-volatile
c) Both a) and b) d) None of these
4) Transfer molding process combines the principle of and transfer
of polymer charge.
a) Injection b) Compression c) Blow d) Rotation
5) The rotational molding is plastic forming process.
a) High temperature
b) Low pressure Low temperature, high pressure
d) High temperature, low pressure
6) Which of the welding process is used for thermoplastics__
a) Hot gas welding b) Induction heating
c) Heated tool d) All of the above
7) In welding method, the workpieces to be joined are irradiated
with a steam of neutrons.
P.T.O.
a) Infrared b) Nuclear c) Hot gas d) Heated tool
 SLR-PK – 151 -2-

8) What should be the draft for Nylon material ?

a) 0 – 1/4° b) 0 – 1/8° c) 0 – 1/2° d) 0 – 1/3°
9) The rib thickness should be between of wall thickness.
a) 30% and 40% b) 40% and 60%
c) 50% and 60% d) 60% and 80%
10) The properties of the polymer will also depend on the available
for cooling.
a) Colour b) Rate
c) Both colour and rate d) None of above
11) Polymers have very thermal conductivity.
a) High b) Medium c) Low d) Very high
12)
a) b)
c) d)
13) It is the operation that sets the shape of thermoplastics.
a) Heating b) Cutting c) Grinding d) Cooling
14) In injection molding melt temperatures are of the order of for
low-density polymers materials.
a) 160 – 190°C b) 120 – 170°C c) 110 – 160°C d) 100 – 150°C
15) It is the operation that sets the shape of thermoplastics.
a) Heating b) Cutting c) Grinding d) Cooling
16) A biodegradable polymer should
a) Contained hydrophilic group b) Contain hydrophobic
c) Group contain only C – C d) Contain aromatic group
17) An example of biodegradable polymer is
a) PHBV b) PVC
c) Polyethylene d) Polyacetylene
18) A biodegradable polymer is one which
a) Can be synthesized by biologicalroute
b) Is degradable by action of microorganism
c) Is not degradable by action of microorganism
d) None of these
19) In compression molding, for phenolic materials suitable pressure range is
kg/cm2.
a) 100 to 158 b) 158 to 211 c) 211 to 258 d) 250 to 300
20) Bulk factor is the ratio of volume of loose plastic powder to the
a) Actual cavity volume b) Volume of the molding
c) Volume of loose plastic powder d) None of these

P.T.O.
Set P
 SLR-EP – 458
Seat No.
Set P
B.E. (Mechanical) (Part – II) (New) Examination, 2016
Elective – II : PLASTIC ENGINEERING
Day and Date : Thursday, 24-11-2016 Max. Marks :
100 Time : 3.00 p.m. to 6.00 p.m.
Instructions : 1) Q. No. 1 is compulsory. It should be solved in first 30 minutes
in Answer Book Page No. 3. Each question carries one mark.
2) Answer MCQ/Objective type questions on Page No. 3
only. Don’t forget to mention, Q.P. Set (P/Q/R/S) on Top of
Page.
3) Assume suitable data whenever necessary and state it clearly.
4) Attempt any 3 questions from Q2, Q3, Q4, Q5 and 3
questions from to Q6, Q7, Q8, Q9.

MCQ/Objective Type Questions

Duration : 30 Minutes Marks : 20

1. Choose the correct answer : (20×1=20)

1) In case of processability testing, MI stands for
a) Moment of Inertia b) Melt Index
c) Malleability Index d) None of above
2) Epoxy resin is example of plastics.
a) Thermoplastics b) Elastomers
c) Thermosetting d) None of above
3) Polymers can be very to chemicals.
a) Resistant b) Similar c) Opposite d) None of above
4) Compression molding process is one of the cost molding method
as compare to injection molding.
a) High b) Medium c) Low d) None of these
5) Transfer molding process combines the principle of and transfer of
polymer charge.
a) Injection b) Compression c) Blow d) Rotation
6) welding is less dependent than other welding methods on the
properties of the materials being welded.
a) Thermal b) Heated tool
c) Induction heating d) All of the above
7) Which of the welding process is used for thermoplastics?
a) Hot gas welding b) Induction heating
c) Heated tool d) All of the above

P.T.O.
SLR-EP – 458 -2-

8) What should be the draft for polyethylene material ?

a) 1/2° b) 1/4° c) 1/8° d) 1/3°
9) What should be the draft for Nylon material ?
a) 0 – 1/4° b) 0 – 1/8° c) 0 – 1/2° d) 0 – 1/3°
10) The rib thickness should be between of wall thickness.
a) 30% and 40% b) 40% and 60%
c) 50% and 60% d) 60% and 80%
11) The properties of the polymer will also depend on the available for
cooling.
a) Colour b) Rate
c) Both colour and rate d) None of above
12) It is the operation that sets the shape of thermoplastics.
a) Heating b) Cutting c) Grinding d) Cooling
13) In Injection molding Melt temperatures are of the order of for low-
density polymers materials.
a) 160 – 190°C b) 120 – 170°C
c) 110 – 160°C d) 100 – 150°C
14) Plasticizers are considered solvents.
a) Volatile b) Non-volatile c) Both a & b d) None of these
15) A biodegradable polymer should
a) Contained hydrophilic group b) Contain hydrophobic
c) Group contain only C-C d) Contain aromatic group
16) An example of biodegradable polymer is
a) PHBV b) PVC
c) Polyethylene d) Polyacetylene
17) A Biodegradable polymer is one which
a) Can be synthesized by biological route
b) Is degradable by action of microorganism
c) Is not degradable by action of microorganism
d) None of these
18) In welding method, the workpieces to be joined are irradiated with
a steam of neutrons.
a) Infrared b) Nuclear
c) Hot gas d) Heated tool
19) In compression molding, for phenolic materials suitable pressure range is
kg/cm2.
a) 100 to 158 b) 158 to 211 c) 211 to 258 d) 250 to 300
20) Bulk factor is the ratio of volume of loose plastic powder to the
a) Actual cavity volume b) Volume of the molding
c) Volume of loose plastic powder d) None of these

Set P
*SLRTC142* SLR-TC –
142
Seat No.
Set P

B.E. (Mechanical) (Part – II) (New) (CGPA) Examination, 2018

PLASTIC ENGINEERING (Elective – II)
Day and Date : Tuesday, 22-5-2018 Total Marks : 70
Time : 2.30 p.m. to 5.30 p.m.
Instructions : 1) Assume suitable data wherever necessary and state
it clearly.
2) Q. No. 1 is compulsory. It should be solved in first 30
minutes in Answer book Page No. 3. Each question
carries one mark.
3) Answer MCQ/Objective type questions on Page No.
3 only. Don’t forget to mention, Q.P. Set (P/Q/R/S) on
Top of Page.

MCQ/Objective Type Questions

Duration : 30 Minutes Marks : 14
1. Choose the correct answer : (14�1=14)
1) Generally Polymers are very in weight with significant
degrees of strength.
a) Heavy b) Light c) a) and b) d) none of above
2) is the most commonly used manufacturing process for
domestic plastic component.
a) Injection moulding b) Transfer moulding
c) Blow moulding d) Rotational moulding
3) moulding is used to produce small hollow plastic part.
a) Blow moulding b) Injection moulding
c) Compression moulding d) Rotational moulding
4) moulding is used to produce overhead hollow
plastic water storage tanks.
a) Rotational moulding b) Injection moulding
c) Compression moulding d) Transfer moulding
5) The rotational moulding is plastic forming process.
a) high temperature b) low temperature
P.T.O.
c) low temperature high pressure d) high temperature low pressure

Set P
SLR-TC – 142 -2- *SLRTC142*

6) Plastic sheet making is also called as

a) Blow moulding b) Calendering
c) Rotary moulding d) none of above
7) The pot type feeder system is used in
a) Transfer moulding b) Calendering
c) Rotary moulding d) Blow moulding
8) For the more precise dimensional stability of Thermosets,
is used.
a) Compression moulding b) Calendering
c) Transfer moulding d) Any moulding process
9) Design of is the most important design aspect in Plastic
moulding.
a) Corner b) Wall thickness
c) Rib d) Hole
10) The complicated joints are produced by
a) High frequency Ind. Welding b) Hot gas Welding
c) Hot tool Welding d) Both b) and c)
11) The inserts are generally made of
a) similar material as the plastic b) metals
c) glass d) rubber
12) Which gas is used commonly in hot gas welding ?
a) Hot air b) Oxygen
c) nitrogen d) none of above
13) Which of the following is an additive used for saving base plastic material ?
a) Fillers b) Pigments c) Plastisizers d) none of these
14) In which of the following moulding method is used to make long hollow
pipes ?
a) Casting b) Injection moulding
c) Compression moulding d) extrusion moulding

P.T.O.
*SLRTX183* SLR-TX –
183 P
Seat
no. Set

B.E. (Mechanical) (Part – II) (CGPA) Examination, 2018

PLASTIC EnGInEERInG (Elective – II)

Day and Date : Monday, 26-11-2018 Max. Marks : 70

Time : 2.30 p.m. to 5.30 p.m.

Instructions : 1) Q. No. 1 is compulsory. It should be solved in first

30 minutes in Answer Book Page No. 3. Each question
carries one mark.
2) Answer MCQ/Objective type questions on Page No. 3
only. Don’t forget to mention, Q.P. Set (P/Q/R/S) on
Top of Page.
3) Assume suitable data whenever necessary and state it
clearly.
MCQ/Objective Type Questions
Duration : 30 Minutes Marks : 14

1. Choose the correct answer : (14×1=14)

1) Outer corner radius should be normally times the wall thickness.
a) 1.5 b) 2.5 c) 5.5 d) 0.5
2) The ratio of the volume of loose plastic powder to the volume of moulding
is known as
a) clamping force b) density
c) bulk factor d) none of the above
3) The excess material flow out of the cavity and form a thin layer of plastic
film is called as
a) flash b) sink marks
c) wastage d) none of the above
4) Which of the following is the type of compression moulding ?
a) semi automatic open flash moulding
b) hand compression mould
c) semi automatic semi positive mould
d) all of the above
5) Material used for compression mould construction is
a) Special purpose tool steel b) Carbon steel
c) Stainless steel d) All of the above
Set P
SLR-TX – 183 -2- *SLRTX183*
6) The process in which measured quantity of preform thermoset polymer
material is heated in the pot and it is transferred into mould cavity is
a) blow moulding b) transfer moulding
c) compression moulding d) none of the above
7) The gating system is usually provided on the
a) movable half b) both half of the mould
c) anywhere d) rear stationary half
8) The properties of the polymer will also depend on the available
for cooling.
a) speed b) area
c) momentum d) none of the above
9) Polymers have very thermal conductivity.
a) high b) medium c) low d) very high
10) The operating temperature for a particular mould will depend upon
following factors
a) type and grade of plastic material
b) wall section of the moulding
c) length of feed system
d) all of the above
11) An example of biodegradable polymer is
a) PHBV b) PVC c) Polyethylene d) Polyacetylene
12) Which gas is used commonly in hot gas welding ?
a) Hot air b) Inert gas
c) Both a and b d) None of the above
13) For normal sized molding land should be
a) 15 mm to 25 mm b) 4 mm to 9 mm
c) 1 mm to 5 mm d) 9 mm to 16 mm
14) Rotational moulding is used for manufacturing of
a) Elbow joints b) Plastic bottles
c) Water tanks d) All above

P.T.O.
 SLR-FM-171
Set P
Seat No.

B.E. (Part – II) (CGPA) Examination Nov/Dec-2019

Mechanical Engineering
PLASTIC ENGINEERING
Day & Date: Tuesday, 26-11-2019 Max. Marks:
70 Time: 02:30 PM To 05:30 PM
Instructions: 1) Q.No.1 Objective question is compulsory. It should be solved in first
30 minutes in the Answer Book.
2) Assume suitable data whenever necessary and state it clearly.
MCQ/Objective Type Questions
Duration: 30 Minutes Marks: 14
Q.1 Choose the correct alternatives from the options and rewrite the 14
sentence.
1) are the materials added to plastics materials to raise
mechanical properties.
a) Fillers b) Plasticizers
c) Reinforcing agents d) None
2) molding is manufacturing process that is used to produce
hollow plastic part.
a) Blow b) Injection
c) Compression d) Transfer
3) Generally polymers are very in weight with significant degrees
of strength.
a) Heavy b) Light
c) Both a & b d) None
4) Which of the welding process is used for thermoplastics?
a) Hot gas welding b) Induction heating
c) Heated tool d) All of the above
5) Materials having a shrinkage allowance can be molded with
close tolerance.
a) Low b) High
c) Medium d) None
6) Due to the nature of plastic the dimension of plastic parts after
molding and cooling is than that of the cavity.
a) Smaller b) Bigger
c) Same d) None
7) Which of the following is the type of compression moulding?
a) Semi-automatic open flash mould
b) Hand compression mould
c) Semi-automatic semi positive mould
d) All of above
8) The area of the pot in pot type transfer mould should be 20-30%
than the projected area.
Set P
a) Higher b) Smaller
c) Same d) None

Page 1 of 16
 SLR-FM-171
Set P
9) Injection mold bases, cavities, and cores are most commonly
made from .
a) special aluminums b) epoxies
c) beryllium copper d) special mold steels
10) The usual range of mold draft angles is .
a) 5o to 10o per side b) 1 to 4o per side Bevel
o

c) 1o to 2o per side d) 0.5o to 1o per side

11) Polymers have very thermal conductivity.
a) high b) medium
c) low d) very high
12) Processing operations, however, demand a „cooling‟ operation.
a) low b) quick
c) medium d) moderate
13) A biodegradable polymer should .
a) contained hydrophilic group b) contain hydrophobic
c) group contain only C-C d) contain aromatic group
14) An example of biodegradable polymer is .
a) PHBV b) PVC
c) Polyethylene d) Polyacetylene

Page 2 of 16