Quick Connect Coupling Catalog: Eaton Hansen

Eaton® Hansen™
Quick Connect Coupling Catalog

Table of Contents
Page Number
How to Build a Socket Part No. 3
Market & Application Reference 7 Page Number
One-Way Shutoff Couplings Straight Through Couplings

Contents and Selection Chart 6 Contents and Selection Chart 61
One-Way Plug Interchange Chart 7 ST Series 62-64
CC Series 8 P2-ST & P3-ST Series 65
1000/400/500 Series 9-12 FLO-TEMP 200/300/500 Series 66-67
3000/4000/5000/6000 Series 13-17
P-30 & P-40 Series 18
Gas Couplings
Auto-Flo 23 & 24 Series 19-21
Gas-Mate Series 69
Safeline Series 22
180 & 280 Series 23-24
100 Series 25-26 Accessories
600 & 700 Series 27-29 FS Flow Sensor Series 71
2RL & 3RL Series 30-32 In-Line Check Valves 72
Full Bore Series 33-34 Flex-Air Fittings 73-74
210 & 310 Series 35-36 Fittings 76
MS Series 37-38 Elastomer Selection Guide 77
Two-Way Shutoff Couplings Index

Contents and Selection Chart 40 Technical & Warranty 78
HK 1-8 Series 41-43
HK 10, 12, 20 Series 44-46
HKFR Series 47
HA 15000 Series 48-49
FF Flat Face Series 50-52
5100 Series 53
UP10 Series 54-55
WA 56000 & HP3 Series 56
2-HKIG & 2-HKIL 57-58
DB Series 59
2
eaton Quick Disconnect Couplings
Notes:
1) Some part numbers may be subject to minimum order quantities.
2) Options shown are not available for all parts and may only be available by
quotation. Consult your local distributor.
EXAMPLE: 1000 – BV – SL – 143 – OC
OC – Oxygen Clean
Standard part number
from table listing.
Seal Material*:
138 – Silicone
SL – Sleeve Lock 143 – Fluorocarbon
Valve Material: 192 – EPDM
BV – Brass Valve 115 – PTFE
LLV – 303 Stainless Steel 118 – Neoprene
*See page 77 for full list, description and suggested uses for seal materials.
Not all seal materials available in all series.
CLEANING AND LUBRICATION PROCESS FOR GASEOUS OR OXYGEN SERVICE

<<< Part numbers cleaned for oxygen service should be denoted with an “OC” suffix >>>
This cleaning process applies to new and unused brass or stainless steel parts for 3000 psig
(207 Bar) max oxygen or aluminum parts for 150 psig (10 Bar) max gaseous or oxygen service.
It is based upon the recommended practices in ASTM G93 and CGA G-4.1 for cleaning, drying,
inspection and packaging of materials and equipment intended for service in an oxygen-enriched
environment. Eaton’s cleaning procedure for oxygen service is available upon request.
Over-pressurization could Couplings do wear out.

result in a sudden failure of In order to avoid severe
the coupling causing severe bodily injury or death,
bodily injury or death. Be sure couplings must be routinely
to select the proper coupling checked for condition and
for your application and use replaced if necessary.
it only within the specified
service pressure range.
3
Market and Application Reference Guide
Aerospace Agriculture Breathing Carpet Chemical

Air Cleaning
Construction Defense Energy Food and General

and Power Beverage Pneumatics
Heating/Cooling/ Injection Marine Medical Mining

Refrigeration Molding
Petrochemical Pharmaceutical Recreation Transportation Water and

and Wastewater
Entertainment Treatment
Eaton is Proud to Hold the

Following Certifications:
CANADIAN
CRN
ISO 9001:2000
REGISTRATION
NUMBER
Eaton is CRN certified for all non-nuclear applications in all of the
Canadian provinces for our Hansen™ coupling products. Ontario
Regulation 220/01 for Boilers and Pressure Vessels in Paragraph 4,
states requirements for Design Registration. Eaton is the only
coupling manufacturer that has achieved this registration. Our CRN
Certificate No. 006888 is OA11599.5C and our approval is valid until 2017.
PROUD MEMBERS OF:
4
ONE-WAY
5
Contents and Selector Chart
ONE-WAY
Coupling Locking
Interchange Body Size Body Material Options
Style Mechanism
STEEL (Zinc/chromate Finish)

INDUSTRIAL INTERCHANGE
SEAL MATERIALS (Various)

HANSEN UNIQUE DESIGN
CEJN 320/RECTUS 25
MANUAL CONNECT
PUSH-TO-CONNECT
SAFETY COUPLING
STAINLESS STEEL
PLASTIC FINGERS
DUST CAP (Vinyl)

PLASTIC (Acetal)
SLEEVE LOCK
ARO 210/310
BALL LOCK
RING LOCK
TRU-FLATE
ALUMINUM
PIN LOCK
1/8 INCH
1/4 INCH
3/8 INCH
1/2 INCH
3/4 INCH
BRASS
Coupling
Series Page
CC 8 ●●●●●● ●● ● ♦ ▼
1000 10 ● ● ● ● ● ● ● ● ●
400 11 ● ● ● ● ● ● ● ● ●
500 12 ● ● ● ● ● ● ●
3000 14 ● ● ● ● ● ● ● ●
4000 15 ● ● ● ● ● ● ● ●
5000 16 ● ● ● ● ● ● ●
6000 17 ● ● ● ● ● ● ●
P30 18 ● ● ● ● ●
P40 18 ● ● ● ● ●
Auto-Flo 23 20 ● ●●● ● ● ●
Auto-Flo 24 21 ● ● ● ● ●
Safeline 22 ●●● ● ● ● ●
180/280 23/24 ● ●● ● ● ●
100 25/26 ● ● ● ● ● ●●
600/700 27 ● ● ● ● ● ● ●
2RL 31 ● ● ● ● ● ▼● ●
3RL 32 ● ● ● ● ● ▼● ●
Full-Bore 33/34 ●●● ●● ● ● ▼
210 35/36 ● ● ● ● ●
310 35/36 ● ● ● ● ●
MS 37/38 ● ● ● ● ●
▼Sleeve lock is standard ♦ Polymer Sleeves
6
One-Way Plug Interchange Chart
The plug profiles shown below are actual size. This chart can be used to help select Eaton one-way
couplings. The bottom row of this chart and the 180/280 are unique Eaton plug designs.
ONE-WAY
TWO-WAY
1/4" 3/8" 1/2" 1/2"
Industrial Interchange
STRAIGHT-THRU
1/4" 3/8" 1/4" 3/8" 1/4" 1/8"
ARO 210 ARO 310 Tru-Flate Tru-Flate Auto-Flo 24 180/280
GAS
ACCESSORIES
1/4" 1/4" 1/4" 1/4" 3/8"

100 600 700 2RL 3RL
7
Pneumatic Coupling
CC Series
Interchangeability
2CC 24CC 3CC
Industrial CEJN 320 Industrial
ARO 210
Tru-Flate RECTUS 25 ARO 310
Materials
• Non-marring polymer sleeves and
rounded ends
• Nickel plated brass and crush
resistant polymer
The CC Series provides unrestricted air flow, safety,
efficiency and extreme durability all in one pneumatic
1/4" to 3/8" nominal
coupling.
(6.35 mm to 8 mm)
F eatures
Rated Pressure
• Two-sleeve activation for safety Series PSI BAR
• Exceeds stringent cycle testing requirements without leakage 2CC 250 17
3CC 250 17
• Withstands 4,500 pounds of external force without cracking 24CC 250 17
• The safe choice for your employees due to safety venting that
prevents hose whip Flow Capacity
• Helps prevent scratches on finished product surfaces PRESSURE DROP VS. AIR FLOW
(100 psig inlet pressure)
• Does not noticeably increase the weight of the tool when 10.0
attached, which helps prevent user strain and fatigue,

increasing workplace productivity 5.0
• The socket can accept multiple plug configurations, making it

extremely flexible
PRESSURE DROP, psid
3CC
A pplications & markets 1.0 2CC
• Air Tools • General Pneumatics 24CC
Part Body Thread Rated

Number Size Size Air Flow
Interchanges *
2CC25F 1/4" 1/4" Female NPT 34 SCFM Industrial, ARO 210, Tru-Flate
0.1
2CC37F 1/4" 3/8" Female NPT 34 SCFM Industrial, ARO 210, Tru-Flate 1 10 100
AIR FLOW, scfm
3CC25F 3/8" 1/4" Female NPT 60 SCFM Industrial, ARO 310
*scfm: Standard Cubic Feet per Minute
24CC25F 1/4" 1/4" Female NPT 53 SCFM CEJN 320, Rectus 25
24CC37F 1/4" 3/8" Female NPT 53 SCFM CEJN 320, Rectus 25
1/4" Female
24CC25FBS 1/4" 53 SCFM CEJN 320, Rectus 25
BSPP
8
1000/400/500 Series
ONE-WAY
Interchangeability
All Sizes 1/4" & 1/2" 400 Series
US ISO 6150 Series B Tru-Flate
Industrial A-A-59439
Interchange (former MIL-C-4109)
Materials
Socket:
• Brass Body
• Nickel Plated Steel Sleeve
• Zinc Plated Steel Valve
TWO-WAY
• Buna-N (Nitrile) Seal
Industrial Interchange Ball Lock quick • Stainless Steel Springs
connect couplings are designed for compressed air, • Stainless Steel Locking Balls
gases, and liquids. Body sizes are 1/4", 3/8" and 1/2". Plug:
• Zinc Plated Case-Hardened Steel
• Brass
F eatures
• Stainless Steel (1/4" size)
• Ball lock
STRAIGHT-THRU
• Manual operation 1/4" to 1/2" nominal
(6.35 mm to 12.7 mm)
• Rugged, reliable
• All sizes accept US Industrial Interchange; 1/4" and 1/2"
-40° F to 250° F
also accept ISO 6150 Series B and A-A-59439 (former
MIL-C-4109) plugs -40° C to 120° C
• Optional sleeve lock prevents accidental disconnection
Rated Pressure NOTE:
• Optional seal and valve materials available Series Size PSI BAR Series 400 operating
pressure is 150 psi
• Series 1000 socket available in stainless steel 1000 1/4” 2,000 138
when connected
400 3/8” 1,000 69
• Series 400 sockets accept Tru-Flate Interchange plugs and 500 1/2” 500 35
to Tru-Flate
Interchange plug.
Industrial Interchange plugs
Flow Capacity
A pplications & markets Series † Ac
† Air flow (scfm)
with 5 psi pressure
GAS
• General Pneumatics • Industrial Plants 1000 24 drop and 100 psig
400 45 inlet pressure.
• Construction • Fluid Transfer 500 72
ACCESSORIES
SOCKET END
VALVE SPRING SLEEVE SOCKET BODY
VALVE SLEEVE SPRING LOCKING BALL
VALVE WASHER DRIVE SCREW
Shown with optional sleeve lock
9
1/4” Nominal
1000 Series
SOCKETS PLUGS
Part No. Dimensions Male End Connections Part No. Dimensions
Brass Thread Size A B HEX A Steel Thread Size C D HEX
C
900 1/8-27 NPTF 1.97 1.00 0.69 10 1/4-18 NPTF 1.75 0.65 0.56
1100 1/4-18 NPTF 2.16 1.00 0.69 B D 10C§ 1/4-18 NPTF 1.75 0.65 0.56
1300 3/8-18 NPTF 2.12 1.00 0.69 HEX HEX
10G† 1/4-18 NPTF 1.75 0.65 0.56
12 1/8-27 NPTF 1.59 0.58 0.50
Stainless 12G† 1/8-27 NPTF 2.38 0.77 0.69
LL1100 1/4-18 NPTF 2.16 1.00 0.69 14 3/8-18 NPTF 1.75 0.79 0.69
14G† 3/8-18 NPTF 2.53 0.77 0.69
Brass
B10 1/4-18NPTF 1.75 0.64 0.56
Stainless
LL10 1/4-18 NPTF 1.75 0.65 0.56
Dimensions Female End Connections Part No. Dimensions

Part No. Thread Size A B HEX A C Steel Thread Size C D HEX
800 1/8-27 NPTF 1.86 1.00 0.69 11 1/4-18 NPTF 1.63 0.79 0.69
1000 1/4-18 NPTF 2.08 1.00 0.69 B D
11G† 1/4-18 NPTF 2.44 0.77 0.69
1200 3/8-18 NPTF 2.16 1.00 0.75 HEX HEX 13 1/8-27 NPTF 1.47 0.65 0.56
15 3/8-18 NPTF 1.69 0.94 0.81
Stainless
LL1000 1/4-18 NPTF 2.08 1.00 0.69 Brass
11B 1/4-18 NPTF 1.63 0.78 0.69
Stainless
LL11 1/4-18 NPTF 1.63 0.79 0.69
Dimensions Hose Stem End Connections Part No. Dimensions

Part No. Hose I.D. A B A Steel Hose I.D. C D
C
1600 1/4" 2.60 1.00 16 1/4" 2.22 0.50
1600P‡ 1/4" 2.37 1.00 B D 16G† 1/4" 2.97 0.77
1700 3/8" 2.60 1.00 16P‡ 1/4" 2.00 0.69
HEX
1700P‡ 3/8" 2.44 1.00 17 3/8" 2.22 0.50
1800 5/16" 2.60 1.00 17G† 3/8" 2.96 0.77
17P‡ 3/8" 2.06 0.87
18 5/16" 2.22 0.50
1600P 1700P 16P 17P Brass
B17 3/8" 2.22 0.50
Hose Dimensions Hose Clamp End Connections Part No. Hose Dimensions
Part No. I.D. O.D. A B HEX Steel I.D. O.D. C D HEX
1SB1 1/4" 15/32" 2.69 1.00 0.63 A C
3PB1 1/4" 15/32" 2.31 0.70 0.63
1SB3 1/4" 1/2" 2.69 1.00 0.63 3PB3 1/4" 1/2" 2.31 0.70 0.63
B D
1SB5 1/4" 9/16" 2.69 1.00 0.69 3PB5 1/4" 9/16" 2.31 0.77 0.69
1SB7 1/4" 5/8" 2.69 1.00 0.75 HEX HEX 3PB7 1/4" 5/8" 2.31 0.84 0.75
1SC5 5/16" 9/16" 2.81 1.00 0.69 3PB11 1/4" 3/4" 2.31 0.98 0.88
1SC7 5/16" 5/8" 2.81 1.00 0.75 3PC5 5/16" 9/16" 2.38 0.77 0.69
1SD5 3/8" 9/16" 2.81 1.00 0.69 3PC7 5/16" 5/8" 2.38 0.84 0.75
1SD7 3/8" 5/8" 2.81 1.00 0.75 3PC9 5/16" 11/16" 2.38 0.91 0.81
1SD9 3/8" 11/16" 2.81 1.00 0.81 3PD5 3/8" 9/16" 2.44 0.77 0.69
1SD11 3/8" 3/4" 2.81 1.00 0.88 3PD7 3/8" 5/8" 2.44 0.84 0.75
3PD9 3/8" 11/16" 2.44 0.91 0.81
3PD11 3/8" 3/4" 2.44 1.98 0.88
* 45° Male Flare § With Ball Check † With Bleeder Ball Check – Reduces hose whip when disconnecting ‡ For use with push-on style hose
Optional Seal Materials: 138-Silicone, 143-Fluorocarbon, 192-EPDM
10
3/8” Nominal
400 Series
SOCKETS PLUGS
Dimensions Male End Connections Part No. Dimensions
Part No. Thread Size A B HEX Steel Thread Size C D HEX
410 1/4-18 NPTF 2.35 1.13 0.88 38 1/8-27 NPTF 1.72 0.72 0.63
430 3/8-18 NPTF 2.35 1.13 0.88 40 1/4-18 NPTF 1.88 0.72 0.63
450 1/2-14 NPTF 2.54 1.13 0.88 40G† 1/4-18 NPTF 2.65 0.77 0.69
ONE-WAY
42 3/8-18 NPTF 1.88 0.79 0.69
42G† 3/8-18 NPTF 2.65 0.77 0.69
44 1/2-14 NPTF 2.09 1.01 0.88
Brass
B40 1/4-18 NPTF 1.88 0.70 0.63
B42 3/8-18 NPTF 1.88 0.77 0.69
Steel
31AP25M 1/4-18 NPTF 1.85 0.72 0.63
31AP37M 3/8-18 NPTF 1.85 0.79 0.69
Female End Connections Part No. Dimensions

Dimensions
Steel Thread Size C D HEX
TWO-WAY
Part No. Thread Size A B HEX
41 1/4-18 NPTF 1.63 0.79 0.69
400 1/4-18 NPTF 2.10 1.13 0.88
41G† 1/4-18 NPTF 2.56 0.77 0.69
420 3/8-18 NPTF 2.35 1.13 0.88 43 3/8-18 NPTF 1.81 0.94 0.81
440 1/2-14 NPTF 2.62 1.13 1.00 43G† 3/8-18 NPTF 2.62 0.84 0.75
45 1/2-14 NPTF 2.06 1.15 1.00
Brass
B43 3/8-18 NPTF 1.81 0.91 0.81
Steel
31AP25F 1/4-18 NPTF 1.60 0.79 0.69
31AP37F 3/8-18 NPTF 1.78 0.94 0.81
STRAIGHT-THRU
Part No. Hose I.D. A B Steel Hose I.D. C D
4004 1/4" 2.82 1.13 404 1/4" 2.34 0.63
4006 3/8" 2.82 1.13 406 3/8" 2.34 0.63
4008 1/2" 2.82 1.13 408 1/2" 2.34 0.81
Brass
B406 3/8" 2.34 0.63
40SD7 3/8" 5/8" 3.04 1.13 0.75 4PB3 1/4" 1/2" 2.44 0.70 0.63
40SD9 3/8" 11/16" 3.04 1.13 0.81 4PB7 1/4" 5/8" 2.44 0.84 0.75
40SD11 3/8" 3/4" 3.04 1.13 0.88 4PD7 3/8" 5/8" 2.56 0.84 0.75
4PD9 3/8" 11/16" 2.56 0.91 0.81
13/16" 3.67
GAS
40SP13 1/2" 1.13 0.94
4PD11 3/8" 3/4" 2.56 0.98 0.88
40SP15 1/2" 7/8" 3.67 1.13 1.00 4PP13 1/2" 13/16" 3.25 1.05 0.94
40SP19 1/2" 1" 3.67 1.13 1.13 4PP15 1/2" 7/8" 3.25 1.12 1.00
ACCESSORIES
† With Bleeder Ball Check – Reduces hose whip when disconnecting
Dust Plugs Accessories:

Optional Seal Materials:
Coupling Series Socket Dust Plug Part No. 138-Silicone,
1000 PSDC1HK
143-Fluorocarbon,
400 PSDC2HK
Vinyl Dust Plug 192-EPDM
11
1/2” Nominal
500 Series
SOCKETS PLUGS
501 1/4-18 NPTF 2.77 1.19 1.00 50 1/4-18 NPTF 2.25 0.79 0.69
510 3/8-18 NPTF 2.78 1.19 1.00 50G† 1/4-18 NPTF 2.90 0.98 0.88
530 1/2-14 NPTF 2.97 1.19 1.00 52 3/8-18 NPTF 2.25 0.87 0.75
550 3/4-14 NPTF 2.97 1.19 1.06 52G† 3/8-18 NPTF 2.90 0.98 0.88
54 1/2-14 NPTF 2.44 1.01 0.88
54G† 1/2-14 NPTF 3.09 0.98 0.88
56 3/4-14 NPTF 2.50 1.23 1.06
56G† 3/4-14 NPTF 3.14 1.19 1.06
Brass
B52 3/8-18 NPTF 2.25 0.70 0.63
B54 1/2-14 NPTF 2.44 0.77 0.88

500A 1/4-18 NPTF 2.72 1.19 1.00 53A 1/4-18 NPTF 1.92 0.79 0.69
500 3/8-18 NPTF 2.78 1.19 1.00 53 3/8-18 NPTF 2.06 0.94 0.81
520 1/2-14 NPTF 3.06 1.19 1.00 53G† 3/8-18 NPTF 2.90 0.98 0.88
540 3/4-14 NPTF 3.09 1.19 1.19 55 1/2-14 NPTF 2.34 1.15 1.00
55G† 1/2-14 NPTF 3.17 0.98 0.88
57 3/4-14 NPTF 2.44 1.37 1.19
Part No. Dimensions Hose Stem End Connections Part No. Dimensions
Brass Hose I.D. A B Steel Hose I.D. C D
570 3/8" 3.32 1.19 585 5/16" 2.66 0.69
580 1/2" 3.24 1.19 585G† 5/16" 3.37 0.98
590 3/4" 4.09 1.19 59 3/8" 2.66 0.69
59G† 3/8" 3.37 0.98
60 1/2" 2.66 0.75
60G† 1/2" 3.37 0.98
61 3/4" 3.50 1.00
61G† 3/4" 4.22 0.98
Brass
B60 1/2" 2.75 0.88
50SP13 1/2" 13/16" 4.09 1.19 0.94 5PB3 1/4" 1/2" 2.81 0.70 0.63
50SP15 1/2" 7/8" 4.09 1.19 1.00 5PB7 1/4" 5/8" 2.81 0.84 0.75
50SR23 3/4" 11/8" 4.22 1.40 1.25 5PD5 3/8" 9/16" 2.94 0.77 0.69
50SR25 3/4" 13/16" 4.22 1.47 1.31 5PD7 3/8" 5/8" 2.94 0.84 0.75
5PD9 3/8" 11/16" 2.94 0.91 0.81
5PD11 3/8" 3/4" 2.94 0.98 0.88
5PD13 3/8" 13/16" 2.94 1.05 0.94
5PP13 1/2" 13/16" 3.62 1.05 0.94
5PP15 1/2" 7/8" 3.62 1.12 1.00
5PR23 3/4" 11/8" 3.75 1.40 1.25
5PR25 3/4" 13/16" 3.75 1.47 1.31
5PR27 3/4" 11/4" 3.75 1.54 1.38
Optional Seal Materials: 143-Fluorocarbon, 192-EPDM
12
3000/4000/5000/6000 Series
ONE-WAY
Interchangeability
All Sizes 1/4" & 1/2"
US ISO 6150 Series B
Materials
Socket:
• Brass Body
TWO-WAY
Industrial Interchange Pin Lock • Stainless Steel Springs
couplings designed for compressed air, gases, and • Stainless Steel Locking Pins
Plug:
liquids. Body sizes are 1/4", 3/8", 1/2" and 3/4".
• Zinc Plated Case-Hardened Steel
• Brass
F eatures • Stainless Steel (1/4" only)
• The original automatic one-way shutoff coupling
STRAIGHT-THRU
designed by Hansen—The Industry Standard 1/4" to 3/4" nominal
• Easy, automatic, push-to-connect design provides (6.35 mm to 19.05 mm)
instantaneous connection and disconnection of
lines, plus automatic shut-off of socket end of line -40° F to 250° F
• All sizes accept US Industrial Interchange; 1/4" and 1/2" -40° C to 120° C
also accept ISO 6150 Series B and A-A-59439 (former
MIL-C-4109) plugs Rated Pressure
• Optional sleeve lock prevents accidental disconnection Series Size PSI BAR
3000 1/4" 2,000 138
• Optional seal and valve materials available 4000 3/8" 1,000 69
5000 1/2" 500 35
A pplications & markets 6000 3/4" 220 15
• Industrial Breathing Air • Maintenance & Repair Flow Capacity

• General Pneumatics • Fluid Transfer
GAS
Series † Ac
† Air flow (scfm)
3000 24 with 5 psi pressure
4000 45 drop and 100 psig
6000 125
ACCESSORIES
Shown with optional sleeve lock.
13
1/4” Nominal
3000 Series
SOCKETS PLUGS
C
2900 1/8-27 NPTF 2.00 1.19 0.69 10 1/4-18 NPTF 1.75 0.65 0.56
3100 1/4-18 NPTF 2.19 1.19 0.69 B D 10C§ 1/4-18 NPTF 1.75 0.65 0.56
3300 3/8-18 NPTF 2.15 1.19 0.69 HEX HEX
10G† 1/4-18 NPTF 1.75 0.65 0.56
300043* 7/16–20 2.10 1.19 0.69 12 1/8-27 NPTF 1.59 0.58 0.50
12G† 1/8-27 NPTF 2.38 0.77 0.69
14 3/8-18 NPTF 1.75 0.79 0.69
14G† 3/8-18 NPTF 2.53 0.77 0.69
Brass
B10 1/4-18 NPTF 1.75 0.64 0.56
Stainless
LL10 1/4-18 NPTF 1.75 0.65 0.56
Female End Connections Part No. Dimensions

Part No. Dimensions
Brass Thread Size A B HEX A
C
11 1/4-18 NPTF 1.63 0.79 0.69
2800 1/8-27 NPTF 1.89 1.19 0.69 11G† 1/4-18 NPTF 2.44 0.77 0.69
3000 1/4-18 NPTF 2.11 1.19 0.69 B D
13 1/8-27 NPTF 1.47 0.65 0.56
3200 3/8-18 NPTF 2.19 1.19 0.75 HEX HEX 15 3/8-18 NPTF 1.69 0.94 0.81
15G† 3/8-18 NPTF 2.50 0.84 0.75
Brass
11B 1/4-18 NPTF 1.63 0.78 0.69
Stainless
LL11 1/4-18 NPTF 1.63 0.79 0.69
Brass Hose I.D. A B A
Steel Hose I.D. C D
3600 1/4" 2.63 1.19 C 16 1/4" 2.22 0.50
3600P‡ 1/4" 2.40 1.19 B D 16G† 1/4" 2.97 0.77
3700 3/8" 2.63 1.19 16P‡ 1/4" 2.00 0.69
3700P‡ 3/8" 2.47 1.19 16PG† ‡ 1/4" 2.75 0.77
3800 5/16" 2.63 1.19 17 3/8" 2.22 0.50
17G† 3/8" 2.96 0.77
17P‡ 3/8" 2.06 0.87
3600P 3700P 16P 17P 17PG† ‡ 3/8" 2.85 0.87
18 5/16" 2.22 0.50
Brass
B-17 3/8" 2.31 0.50
Part No. Hose Dimensions Hose Clamp End Connections Part No. Hose Dimensions
Brass I.D. O.D. A B HEX Steel I.D. O.D. C D HEX
A C
3SA0 3/16" 7/16" 2.65 1.19 0.56 3PA0 3/16" 7/16" 2.25 0.63 0.56
3SB1 1/4" 15/32" 2.72 1.19 0.63 B D
3PB1 1/4" 15/32" 2.31 0.70 0.63
3SB3 1/4" 1/2" 2.72 1.19 0.63 3PB3 1/4" 1/2" 2.31 0.70 0.63
3SB5 1/4" 9/16" 2.72 1.19 0.69 HEX HEX 3PB5 1/4" 9/16" 2.31 0.77 0.69
3SB7 1/4" 5/8" 2.72 1.19 0.75 3PB7 1/4" 5/8" 2.31 0.84 0.75
3SB9 1/4" 11/16" 2.72 1.19 0.81 3PB9 1/4" 11/16" 2.31 0.91 0.81
3SB11 1/4" 3/4" 2.72 1.19 0.88 3PB11 1/4" 3/4" 2.31 0.98 0.88
3SC5 5/16" 9/16" 2.78 1.19 0.69 3PC5 5/16" 9/16" 2.38 0.77 0.69
3SC7 5/16" 5/8" 2.78 1.19 0.75 3PC7 5/16" 5/8" 2.38 0.84 0.75
3SC9 5/16" 11/16" 2.78 1.19 0.81 3PC9 5/16" 11/16" 2.38 0.91 0.81
3SD5 3/8" 9/16" 2.84 1.19 0.69 3PD5 3/8" 9/16" 2.44 0.77 0.69
3SD7 3/8" 5/8" 2.84 1.19 0.75 3PD7 3/8" 5/8" 2.44 0.84 0.75
3SD9 3/8" 11/16" 2.84 1.19 0.81 3PD9 3/8" 11/16" 2.44 0.91 0.81
3SD11 3/8" 3/4" 2.84 1.19 0.88 3PD11 3/8" 3/4" 2.44 0.98 0.88
3SD13 3/8" 13/16" 2.84 1.19 0.94 3PD13 3/8" 13/16" 2.44 1.05 0.94
3PD15 3/8" 7/8" 2.44 1.12 1.00
14
3/8” Nominal
4000 Series
SOCKETS PLUGS
Male End Connections Part No. Dimensions
Part No. Dimensions A Steel Thread Size C D HEX
C
Brass Thread Size A B HEX 38 1/8-27 NPTF 1.72 0.72 0.63
4100A 1/8-27 NPTF 2.20 1.38 0.88 B D 40 1/4-18 NPTF 1.88 0.72 0.63
4100 1/4-18 NPTF 2.35 1.38 0.88 40G† 1/4-18 NPTF 2.65 0.77 0.69
HEX HEX
3/8-18 NPTF 1.88 0.69
ONE-WAY
4300 3/8-18 NPTF 2.35 1.38 0.88 42 0.79
42G† 3/8-18 NPTF 2.65 0.77 0.69
4500 1/2-14 NPTF 2.54 1.38 0.88
44 1/2-14 NPTF 2.09 1.01 0.88
Brass
B40 1/4-18 NPTF 1.88 0.70 0.63
B42 3/8-18 NPTF 1.88 0.77 0.69

Part No.
Brass Thread Size A B HEX A
C
4000A 1/8-27 NPTF 2.10 1.38 0.88 41 1/4-18 NPTF 1.63 0.79 0.69
41G† 1/4-18 NPTF 2.56 0.77 0.69
4000 1/4-18 NPTF 2.10 1.38 0.88 B D
43 3/8-18 NPTF 1.81 0.94 0.81
4200 3/8-18 NPTF 2.35 1.38 0.88 HEX HEX 43G† 3/8-18 NPTF 2.62 0.84 0.75
TWO-WAY
4400 1/2-14 NPTF 2.62 1.38 1.00 45 1/2-14 NPTF 2.06 1.15 1.00
Brass
B43 3/8-18 NPTF 1.81 0.91 0.81
Brass Hose I.D. A B A Steel Hose I.D. C D
C
40400 1/4" 2.82 1.38 404 1/4" 2.34 0.63
40500 5/16" 2.82 1.38 B D 406 3/8" 2.34 0.63
40600 3/8" 2.82 1.38 408 1/2" 2.34 0.81
2.82 1.38
STRAIGHT-THRU
40800 1/2"
Brass
B406 3/8" 2.34 0.63
Hose Dimensions
Hose Clamp End Connections Part No. Hose Dimensions
Part No.
A C
4SB3 1/4" 1/2" 2.92 1.38 0.63 4PB3 1/4" 1/2" 2.44 0.70 0.63
4SB5 1/4" 9/16" 2.92 1.38 0.69 B D
4PB7 1/4" 5/8" 2.44 0.84 0.75
4PD5 3/8" 9/16" 2.56 0.77 0.69
4SB7 1/4" 5/8" 2.92 1.38 0.75 HEX HEX
4PD7 3/8" 5/8" 2.56 0.84 0.75
4SB9 1/4" 11/16" 2.92 1.38 0.81
4PD9 3/8" 11/16" 2.56 0.91 0.81
4SB11 1/4" 3/4" 2.92 1.38 0.88 4PD11 3/8" 3/4" 2.56 0.98 0.88
4SC7 5/16" 5/8" 2.98 1.38 0.75 4PD13 3/8" 13/16" 2.56 1.05 0.94
4SD5 3/8" 9/16" 3.04 1.38 0.69 4PD15 3/8" 7/8" 2.56 1.12 1.00
4SD7 3/8" 5/8" 3.04 1.38 0.75 4PP13 1/2" 13/16" 3.25 1.05 0.94
4SD9 3/8" 11/16" 3.04 1.38 0.81 4PP15 1/2" 7/8" 3.25 1.12 1.00
4SD11 3/8" 3/4" 3.04 1.38 0.88 4PP19 1/2" 1" 3.25 1.26 1.13
GAS
4SD15 3/8" 7/8" 3.04 1.38 1.00
4SP13 1/2" 13/16" 3.67 1.38 0.94
4SP15 1/2" 7/8" 3.67 1.38 1.00

ACCESSORIES
15
1/2” Nominal
5000 Series
SOCKETS PLUGS
C
50100 1/4-18 NPTF 2.78 1.50 1.00 50 1/4-18 NPTF 2.25 0.79 0.69
5100 3/8-18 NPTF 2.79 1.50 1.00 B D 50G† 1/4-18 NPTF 2.90 0.98 0.88
5300 1/2-14 NPTF 2.98 1.50 1.00 52 3/8-18 NPTF 2.25 0.87 0.75
HEX HEX
5500 3/4-14 NPTF 2.98 1.50 1.06 52G† 3/8-18 NPTF 2.90 0.98 0.88
54 1/2-14 NPTF 2.44 1.01 0.88
54G† 1/2-14 NPTF 3.09 0.98 0.88
56 3/4-14 NPTF 2.50 1.23 1.06
56G† 3/4-14 NPTF 3.14 1.19 1.06
Brass
B52 3/8-18 NPTF 2.25 0.70 0.63
B54 1/2-14 NPTF 2.44 0.77 0.88
Part No. Dimensions Female End Connections Part No. Dimensions

Brass Thread Size A B HEX Steel Thread Size C D HEX
A
5000A 1/4-18 NPTF 2.72 1.50 1.00 C
53A 1/4-18 NPTF 1.92 0.79 0.69
5000 3/8-18 NPTF 2.79 1.50 1.00 B D
53 3/8-18 NPTF 2.06 0.94 0.81
5200 1/2-14 NPTF 3.07 1.50 1.00 53G† 3/8-18 NPTF 2.90 0.98 0.88
HEX HEX 55 1/2-14 NPTF 2.34 1.15 1.00
5400 3/4-14 NPTF 3.10 1.50 1.19
55G† 1/2-14 NPTF 3.17 0.98 0.88
57 3/4-14 NPTF 2.44 1.37 1.19
Brass Hose I.D. A B Steel Hose I.D. C D
50400 1/4" 3.26 1.50 A
585 5/16" 2.66 0.69
50500 5/16" 3.29 1.50
C
585G† 5/16" 3.37 0.98
5700 3/8" 3.33 1.50 B D 59 3/8" 2.66 0.69
5800 1/2" 3.25 1.50 59G† 3/8" 3.37 0.98
5900 3/4" 4.10 1.50 60 1/2" 2.66 0.75
60G† 1/2" 3.37 0.98
61 3/4" 3.50 1.00
61G† 3/4" 4.22 0.98
Brass
B60 1/2" 2.75 0.88
Part No. Hose Dimensions Hose Clamp End Connections Part No. Hose Dimensions
A C
5SD5 3/8" 9/16" 3.50 1.50 0.69 5PB3 1/4" 1/2" 2.81 0.70 0.63
5SD7 3/8" 5/8" 3.50 1.50 0.75 B D 5PB5 1/4" 9/16" 2.81 0.77 0.69
5SD9 3/8" 11/16" 3.50 1.50 0.81 5PB7 1/4" 5/8" 2.81 0.84 0.75
HEX HEX
5SD11 3/8" 3/4" 3.50 1.50 0.88 5PD5 3/8" 9/16" 2.94 0.77 0.69
5SD13 3/8" 13/16" 3.50 1.50 0.94 5PD7 3/8" 5/8" 2.94 0.84 0.75
5SD15 3/8" 7/8" 3.50 1.50 1.00 5PD9 3/8" 11/16" 2.94 0.91 0.81
5SP13 1/2" 13/16" 4.10 1.50 0.94 5PD11 3/8" 3/4" 2.94 0.98 0.88
5SP15 1/2" 7/8" 4.10 1.50 1.00 5PD13 3/8" 13/16" 2.94 1.05 0.94
5SR23 3/4" 11/8" 4.23 1.50 1.25 5PD15 3/8" 7/8" 2.94 1.12 1.00
5SR25 3/4" 13/16" 4.23 1.50 1.31 5PP13 1/2" 13/16" 3.62 1.05 0.94
5SR27 3/4" 11/4" 4.23 1.54 1.38 5PP15 1/2" 7/8" 3.62 1.12 1.00
5PR23 3/4" 11/8" 3.75 1.40 1.25
5PR25 3/4" 13/16" 3.75 1.47 1.31
5PR27 3/4" 1¼" 3.75 1.54 1.38
16
3/4” Nominal
6000 Series
SOCKETS PLUGS
Part No. Dimensions Male End Connections Dimensions
Part No.
C
6300 1/2-14 NPTF 2.94 1.88 1.31 64A 1/2-14 NPTF 2.31 1.15 1.00
6500 3/4-14 NPTF 2.94 1.88 1.31 B D
64GA† 1/2-14 NPTF 3.26 1.12 1.00
6700 1-11½ NPTF 3.13 1.88 1.31 66A 3/4-14 NPTF 2.38 1.23 1.06
ONE-WAY
HEX HEX
66GA† 3/4-14 NPTF 3.26 1.19 1.06
68A 1-11½ NPTF 2.56 1.52 1.31
Brass
B64A 1/2-14 NPTF 2.31 1.12 1.00
B66A 3/4-14 NPTF 2.38 1.19 1.06

A
6200 1/2-14 NPTF 2.85 1.88 1.31 C 65A 1/2-14 NPTF 2.22 1.15 1.00
6400 3/4-14 NPTF 3.00 1.88 1.31 65GA† 1/2-14 NPTF 3.35 1.12 1.00
B D
67A 3/4-14 NPTF 2.22 1.37 1.19
6600 1-11½ NPTF 3.19 1.88 1.56 67GA† 3/4-14 NPTF 3.38 1.33 1.19
HEX HEX
TWO-WAY
69A 1-11½ NPTF 2.41 1.80 1.56
Hose Stem End Connections Part No. Dimensions

Part No. Dimensions
Steel Hose I.D. C D
Brass Hose I.D. A B A
70A 1/2" 2.53 0.94
6800 1/2" 3.21 1.88 C
70GA† 1/2" 3.53 1.12

6900 3/4" 4.06 1.88 B D
71A 3/4" 3.44 1.06
7000 1" 4.07 1.88
71GA† 3/4" 4.38 1.12
72A 1" 3.44 1.31
Brass
STRAIGHT-THRU
B71A 3/4" 3.44 1.06
Dust Caps and Dust Plugs Accessories:

Vinyl Dust Plug
Plug Dust Cap Part No. Socket Dust Plug Part No.
Coupling Series
Metal Vinyl Metal Vinyl
3000 PDC3000* – SDC3000* PSDC1HK
Vinyl Dust Cap
4000 – – – PSDC2HK
5000 – PPDC2HK – –
6000 – PPDC3HK – –
*Brass
GAS
Metal Dust Cap Metal Dust Plug

ACCESSORIES
17
P30 & P40 Series
Interchangeability
All Sizes 1/4" only
US ISO 6150 Series B
Materials
Socket:
• Acetal Body
• Polypropylene Sleeve
Industrial Interchange Plastic quick • Buna-N (Nitrile) Seal
• Stainless Steel Spring
connect couplings designed for compressed air.
Plug:
Body sizes are 1/4" and 3/8".
• Acetal
• Series P30 accepts all Series 3000 plugs
F eatures • Series P40 accepts all Series 4000 plugs
• Plastic socket body and plug
• Light-weight
(6.35 mm to 9.52 mm)
• Less likely to damage painted or easily scratched
surfaces than metal couplings
• Easy, automatic, push-to-connect design provides
Up to 125° F (52° C)
lines, plus automatic shut-off of socket end of line Rated Pressure
Series Size PSI BAR
• Series P30 accepts all series 3000 plugs;
P30 1/4" 150 10
Series P40 accepts series 4000 plugs P40 3/8" 150 10
* At temperatures up to 125°
A pplications & markets
• General Pneumatics Flow Capacity † Air flow (scfm)
Series † Ac with 5 psi pressure
P30 28 drop and 100 psig
P40 45 inlet pressure.
SOCKETS
Hose Stem End Connections
Dimensions
Part No. Hose I.D. A B
P430S25H 1/4" 2.66 1.25
P740S37H 3/8" 2.82 1.44
PLUGS
Male End Connections
Part No. Dimensions
P430P25M 1/4-18 NPTF 1.75 0.65 0.56
18
1/4” Nominal
Auto-Flo 23 & 24 Series
ONE-WAY
Interchangeability
Auto-Flo 23 Auto-Flo 24
US Industrial Interchange (Euro
Interchange)
ISO 6150 Series B
A-A-59439 CEJN 320
(former MIL-C-4109)
Tru-Flate Interchange RECTUS 25
ARO 210 Interchange
TWO-WAY
Materials
Socket:
Auto-Flo 23 & 24 are high flow, automatic • Brass Body
quick connect couplings designed for use with • Brass Valve
compressed air. The universal design makes the • Zinc Plated Steel Sleeve
Auto-Flo an extremely flexible coupling series. • Buna-N (Nitrile) Seal
• Stainless Steel Springs
F eatures • Stainless Steel Locking Balls
Plug:
STRAIGHT-THRU
• Auto-Flo 23 was the first automatic universal coupling • Industrial Interchange
designed to operate with Industrial, ARO 210 and – Zinc Plated Case-Hardened Steel
Tru-Flate Interchange plugs – Brass
– Stainless Steel
• Auto-Flo 24 operates with CEJN 320 and Rectus 25
Interchange plugs • ARO 210, Tru-Flate and
CEJN/Rectus Interchanges
• Easy, automatic, push-to-connect design provides – Zinc Plated Case-Hardened Steel
lines, plus automatic shut-off of socket end of line
1/4" nominal (6.35 mm)
• Sleeve guard protects against accidental disconnection
A pplications & markets -40° F to 250° F

-40° C to 120° C
• General Pneumatics • Air Tools • Construction
GAS
Pressure Ratings
Series PSI BAR
Auto-Flo 23 150 10
Auto-Flo 24 150 10
Flow Capacities
Plug Interchange † Ac † Air flow (scfm)
ACCESSORIES
with 5 psi pressure

Industrial 32
drop and 100 psig
ARO 210 32
inlet pressure.
Tru-Flate 30
Auto-Flo 24 45
19
1/4” Nominal
Auto-Flo 23 Series
SOCKETS PLUGS
B23AS25M 1/4-18 NPTF 2.23 0.94 0.81 10 1/4-18 NPTF 1.75 0.65 0.56
B23AS25MBST 1/4-19 BSPT 2.23 0.94 0.81 10C§ 1/4-18 NPTF 1.75 0.65 0.56
B23AS37M 3/8-18 NPTF 2.23 0.94 0.81 10G† 1/4-18 NPTF 1.75 0.65 0.56
B23AS37MBST 3/8-19 BSPT 2.23 0.94 0.81 12 1/8-27 NPTF 1.59 0.58 0.50
12G† 1/8-27 NPTF 2.38 0.77 0.69
B23AS50MBST 1/2-14 BSPT 2.23 0.94 0.88 14 3/8-18 NPTF 1.75 0.79 0.69
14G† 3/8-18 NPTF 2.53 0.77 0.69
Brass
B10 1/4-18 NPTF 1.75 0.64 0.56
Stainless
LL10 1/4-18 NPTF 1.75 0.65 0.56
ARO 210 Interchange
2607 1/8-27 NPTF 1.42 0.58 0.50
2608 1/4-18 NPTF 1.68 0.65 0.56
2608B 1/4-19 BSPT 1.68 0.65 0.56
20AP37M 3/8-18 NPTF 1.68 0.79 0.69
Tru-Flate Interchange
21AP25M 1/4-18 NPTF 1.65 0.65 0.56

B23AS25F 1/4-18 NPTF 2.02 0.94 0.81 11 1/4-18 NPTF 1.63 0.79 0.69
B23AS25FBS 1/4-19 BSPP 2.02 0.94 0.81 11G† 1/4-18 NPTF 2.44 0.77 0.69
13 1/8-27 NPTF 1.47 0.65 0.56
B23AS37F 3/8-18 NPTF 2.02 0.94 0.81 15 3/8-18 NPTF 1.69 0.94 0.81
B23AS37FBS 3/8-19 BSPP 2.02 0.94 0.81 15G† 3/8-18 NPTF 2.50 0.84 0.75
Brass
11B 1/4-18 NPTF 1.63 0.78 0.69
Stainless
LL11 1/4-18 NPTF 1.63 0.79 0.69
ARO 210 Interchange
2609 1/4-18 NPTF 1.55 0.79 0.69
2609B 1/4-19 BSPP 1.55 0.79 0.69
20AP37F 3/8-18 NPTF 1.61 0.94 0.81
21AP25F 1/4-18 NPTF 1.53 0.79 0.69

Part No. Hose I.D. A B Steel Thread Size C D
B23AS25H 1/4" 2.76 0.94 16 1/4" 2.22 0.50
B23AS31H 5/16" 2.73 0.94 16G† 1/4" 2.97 0.77
B23AS37H 3/8" 2.73 0.94 16P‡ 1/4" 2.00 0.69
17 3/8" 2.31 0.50
17G† 3/8" 2.96 0.77
17P‡ 3/8" 2.06 0.87
18 5/16" 2.22 0.50
Brass
B17 3/8" 2.31 0.50
ARO 210 Interchange
3946 1/4" 2.14 0.50
3947 5/16" 2.14 0.50
22238 3/8" 2.14 0.50
21AP25H 1/4" 2.12 0.50
20
1/4” Nominal
Auto-Flo 24 Series
SOCKETS PLUGS
B24AS25M 1/4-18 NPTF 2.27 0.94 0.81 24AP25MBST 1/4-19 BSPT 1.62 0.65 0.56
24AP37MBST 3/8-19 BSPT 1.62 0.79 0.69
24AP50MBST 1/2-14 BSPT 1.88 1.01 0.88
ONE-WAY
B24AS25F 1/4-18 NPTF 2.06 0.94 0.81 24AP25FG 1/4-18 NPTF 1.49 0.79 0.69
B24AS25FBS 1/4-19 BSPP 2.06 0.94 0.81 24AP25FBS 1/4-19 BSPP 1.46 0.79 0.69
B24AS37FBS 3/8-19 BSPP 2.06 0.94 0.81 24AP50FBS 1/2-1/4 BSPP 1.65 1.23 1.06
B24AS50FBS 1/2-14 BSPP 2.38 0.94 1.06
TWO-WAY
STRAIGHT-THRU
GAS
ACCESSORIES
21
1/4” Industrial Interchange
Safeline Series
Interchangeability
- US Industrial Interchange
- ISO 6150 Series B
- A-A-59439 (Former MIL-C-4109)
Materials
Socket:
• Aluminum and steel construction
Plug:
• Use Series 3000 Plug
The SAFELINE Industrial Interchange
pushbutton safety coupling is designed for use with 1/4" Nominal (6.35 mm)
compressed air. Two-step disconnect procedure shuts off
air supply and releases downstream air pressure before plug -40° F to 250° F
can be removed from socket, which prevents hose whip. -40° C to 120° C
Rated Pressure
F eatures Series PSI Bar
• Safe and easy to connect and disconnect GD 10500 232 16
• Light weight, compact ergonomic design

• Accepts 1/4" ISO 6150 Series B and A-A-59439 (former Flow Capacity † Air flow (scfm)
with 5 psi pressure
MIL-C-4109) plugs Series † Ac
drop and 100 psig
GD 10500 20 inlet pressure.
O peration
• To connect: Push plug into socket Male End
Connections
• To disconnect: (1) Push button on side of socket. Air supply
is shut off and plug pops out 3/16 inch, but is not released
from socket. Downstream air is vented. (2) Push plug into Dimensions
socket to release latch. Pull plug from socket. Part No. Thread Size A B HEX
GD10536 41 1/4-18 NPTF 3.18 1.02 0.67
A pplications & markets GD10536 83 3/8-18 NPTF 3.18 1.02 0.75
• General Pneumatics Female End

• Air Tools Connections
• Industrial Plants
• Maintenance & Dimensions
Repair Part No. Thread Size A B HEX
GD10526 41 1/4-18 NPTF 2.97 1.02 0.67
GD10526 83 3/8-18 NPTF 3.18 1.02 0.87
Hose Stem End

Connections
Dimensions
Part No. Hose I.D. A B
GD10556 01 3/8" 3.56 1.02
22
1/8” Nominal
180 & 280 Series
ONE-WAY
Interchangeability
- Proprietary Interchange
Materials
Socket:
• Brass Body and Sleeve
• Valve
- 180: Nickel Plated Brass Tire Valve
- 280: Brass Series 1-HK Valve
TWO-WAY
Miniature Ball Lock quick connect • Stainless Steel Locking Balls
Plug:
couplings designed for use with compressed air,
• Brass
gases and liquids.
1/8" nominal (3.175 mm)
F eatures
• Ball lock -40° F to 250° F
STRAIGHT-THRU
• Manual operation -40° C to 120° C
• Series 180 and 280 sockets mate with all Series 180
plugs
Pressure Ratings
• Series 180 sockets have a tire valve Series PSI BAR
• Series 280 sockets have a 1-HK valve, which provides 180 700 48
higher flow capacity 280 3,000 207
• Chrome plating available

• Additional seal materials available
Flow Capacities
† Air flow (scfm)
Series † Ac with 5 psi pressure
180 2.5 drop and 100 psig
A pplications & markets inlet pressure.
280 10.0
• Recreation & Entertainment
• Breathing Air
GAS
• General Pneumatics
• Pharmaceutical
• Laboratory Uses
• Medical
ACCESSORIES
23
1/8” Nominal
180 & 280 Series
Series 180
Series 280

Brass Thread Size A B HEX Brass Thread Size C D HEX
180 1/8-27 NPTF 1.41 0.63 0.56 185 1/8-27 NPTF 1.16 0.49 0.44
28S25M 1/4-18 NPTF 1.38 0.63 0.56 186 1/4-18 NPTF 1.44 0.63 0.56

Brass Thread Size A B HEX Brass Thread Size C D HEX
28S12F 1/8-27 NPTF 1.78 0.63 0.56 183 1/8" NPTF 1.19 0.56 0.50
Hose Stem End Connections Part No. Dimensions

Brass Hose I.D. C D
187 1/8" 1.25 0.38
189 3/16" 1.50 0.38
187 189
24
1/4” Nominal
100 Series
ONE-WAY
Interchangeability
Materials
Socket:
• Brass Body
• Brass Valve
• Brass Sleeve
TWO-WAY
• Stainless Steel Locking Balls
100 Series quick connect couplings are Plug:
designed to prevent the crossing of lines. These • Brass
couplings are used for compressed air and gases.
F eatures
-40° F to 250° F
• Ball lock
STRAIGHT-THRU
-40° C to 120° C
• Manual operation
• Non-interchangeable design prevents crossing of lines
Pressure Ratings
A pplications & markets Series PSI BAR
100 350 24
• Industrial Plants Flow Capacities † Air flow (scfm)
with 5 psi pressure
Series † Ac
drop and 100 psig
GAS
ACCESSORIES
25
1/4” Nominal
100 Series
SOCKETS PLUGS
Male End Connections Dimensions
Part No. Dimensions Part No.
Brass Thread Size A B HEX A Brass Thread Size C D HEX
C
101 1/8-27 NPTF 1.94 1.00 0.69 1G1 1/8-27 NPTF 1.38 0.65 0.56
B D
103 1/4-18 NPTF 2.09 1.00 0.69 1G3 1/4-18 NPTF 1.56 0.65 0.56
105 3/8-18 NPTF 2.09 1.00 0.69 HEX HEX 1G5 3/8-18 NPTF 1.56 0.79 0.69
10063* 5/8-18 2.16 1.00 0.69
Female End Connections Dimensions

Part No. Dimensions Part No.
Brass Thread Size A B HEX A Brass Thread Size C D HEX
C
100 1/8-27 NPTF 1.78 1.00 0.69 1G2 1/4-18 NPTF 1.43 0.79 0.69
B D
102 1/4-18 NPTF 2.00 1.00 0.69
104 3/8-18 NPTF 2.06 1.00 0.75 HEX HEX
Dimensions Hose Stem End Connections Dimensions

Part No. Part No.
Brass Hose I.D. A B A Brass Hose I.D. C D
C
110 1/4" 2.53 1.00 1G10 1/4" 2.00 0.56
111 5/16" 2.53 1.00 B D 1G12 3/8" 2.03 0.56
112 3/8" 2.52 1.00
Hose Dimensions
Hose Clamp End Connections
Part No.
Brass I.D. O.D. A B HEX A
1GB3 1/4" 1/2" 2.62 1.00 0.63
1GB7 1/4" 5/8" 2.62 1.00 0.75 B
1GD7 3/8" 5/8" 2.75 1.00 0.75
1GD9 3/8" 11/16" 2.75 1.00 0.81 HEX
* 45° Male Flare

Vinyl Dust Plug
Coupling Series
Vinyl Vinyl
100 PPDC1HK PSDC1HK Vinyl Dust Cap
26
1/4” Nominal
600 & 700 Series
ONE-WAY
Interchangeability
Materials
Socket:
• Brass Body
• Brass Valve
• Painted Brass Sleeve
Green - Series 600
Red - Series 700
TWO-WAY
600 & 700 Series quick connect couplings are • Stainless Steel Locking Balls
designed for use in oxyacetylene service. Series 600 is Plug:
used with oxygen. Series 700 is used with acetylene. • Brass
F eatures 1/4" nominal (6.35 mm)
• Ball lock
STRAIGHT-THRU
-40° F to 250° F
-40° C to 120° C
• Non-interchangeable designs prevent crossing of lines
• Sleeves are color coded to identify each series:
‑ Series 600 sleeves are green for oxygen Pressure Ratings
- Series 700 sleeves are red for acetylene Series PSI BAR
600 & 700 1,500 103
• Series 600 and 700 couplings can also be used with
compressed air and other gases
• Sockets with the SL suffix have the sleeve lock feature to Flow Capacities † Air flow (scfm)
prevent accidental disconnection with 5 psi pressure
Series † Ac drop and 100 psig
• Series 600 and 700 couplings with sleeve lock feature 600 & 700 21 inlet pressure.
comply with OSHA requirements*, which state couplings
shall be the type that cannot be unlocked or disconnected
by means of a straight pull without rotary motion.
GAS
• Breathing Equipment
• Welding
• Shipyards
• Construction
ACCESSORIES
• Nitrous Oxide
TO ADD A THIRD NON-INTERCHANGEABLE

LINE, USE THE 100 SERIES WITH THE 600
AND 700 SERIES.
*29 CFR 1915.55 (f)(5), 1917.152 (d)(3)(iv) and 29 CFR 1926.350 (f)(5)
27
1/4” Nominal
600 Series
See Fittings on Page 75
SOCKETS PLUGS
Part No. - Brass Thread Dimensions Male End Connections Part No. Dimensions
Standard Oxygen Serv. Size A B HEX Brass Thread Size C D HEX
A
GR601 GR601SL 1/8-27 NPTF 1.84 1.00 0.69 C 01A 1/8-27 NPTF 1.41 0.63 0.56
GR603 GR603SL 1/4-18 NPTF 2.03 1.00 0.69 B D
03A 1/4-18 NPTF 1.56 0.63 0.56
GR604R† GR604RSL 9/16-18 1.92 1.00 0.69 04R† 9/16-18 1.41 0.63 0.56
HEX HEX
GR605 GR605SL 3/8-18 NPTF 1.99 1.00 0.69
Part No. - Brass Thread Dimensions Female End Connections Part No. Dimensions
Standard Oxygen Serv. Size A B HEX A Brass Thread Size C D HEX
C
GR600 GR600SL 1/8-27 NPTF 1.73 1.00 0.69 00A 1/8-27 NPTF 1.22 0.63 0.56
GR602 GR602SL 1/4-18 NPTF 1.95 1.00 0.69 B D 02A 1/4-18 NPTF 1.41 0.77 0.69
GR604 GR604SL 3/8-18 NPTF 2.03 1.00 0.69 HEX HEX 05R‡ 9/16-18 1.38 0.77 0.69
GR605R‡ GR605RSL 9/16-18 1.95 1.00 0.69
Part No. - Brass Hose Dimensions Hose Stem End Connections Part No. Dimensions
Standard Oxygen Serv. I.D. A B A Brass Hose I.D. C D
GR606 GR606SL 1/4" 2.47 1.00 C 07A 1/4" 2.03 0.56
GR606P§ GR606PSL§ 1/4" 2.24 1.00 B D 08A 5/16" 2.03 0.56
GR607 GR607SL 5/16" 2.47 1.00 09A 3/8" 2.04 0.56
GR608 GR608SL 3/8" 2.47 1.00
GR608P§ — 3/8" 2.31 1.00
GR-606P GR-608P
Part No. - Brass Hose Dimensions Hose Clamp End Connections Part No. Hose Dimensions
Standard Oxygen Serv. I.D. O.D. A B HEX Brass I.D. O.D. C D HEX
GR60B3 GR60B3-S 1/4" 1/2" 2.56 1.00 0.63 A C 6B3 1/4" 1/2" 2.13 0.70 0.63
GR60B5 GR60B5SL 1/4" 9/16" 2.56 1.00 0.69 6B5 1/4" 9/16" 2.13 0.77 0.69
GR60B7 GR60B7SL 1/4" 5/8" 2.56 1.00 0.75 B D
6B7 1/4" 5/8" 2.13 0.84 0.75
GR60C5 — 5/16" 9/16" 2.62 1.00 0.69 HEX HEX 6B9 1/4" 11/16" 2.13 0.91 0.81
GR60C9 — 5/16" 11/16" 2.62 1.00 0.81 6D5 3/8" 9/16" 2.25 0.77 0.69
GR60D7 — 3/8" 5/8" 2.68 1.00 0.75 6D7 3/8" 5/8" 2.25 0.84 0.75
GR60D9 — 3/8" 11/16" 2.68 1.00 0.81 6D9 3/8" 11/16" 2.25 0.91 0.81
GR60D11 — 3/8" 3/4" 2.68 1.00 0.88 6D11 3/8" 3/4" 2.25 0.98 0.88
† R.H. Thread - 30° Female Flare ‡ R.H. Thread - Inverted Flare § For use with push-on style hose.
Series 600 couplings are not to be used with oxygen at pressures

exceeding 100 psig.
Oxygen increases combus-
tibility. Fire and explosion
could occur causing severe
bodily injury or death. Be
sure to select the proper cou-
pling for your application and
use it only within the speci-
Series 600 and 700 couplings with sleeve lock feature comply with O.S.H.A.
requirements, Sec. 1915.35 (f)(5), 1916.35 (f)(5), 1917.35 (f)(5), and 1926.350 (f)(5).
fied service pressure range.
28
1/4” Nominal
700 Series
See Fittings on Page 75
ONE-WAY
SOCKETS PLUGS
Part No. - Brass Thread Dimensions Male End Connections Part No. Dimensions
Standard Acetyl. Serv. Size A B HEX Brass Thread Size C D HEX
A
RD701 — 1/8-27 NPTF 1.84 1.00 0.69 C A1 1/8-27 NPTF 1.47 0.63 0.56
RD703 RD703SL 1/4-18 NPTF 2.02 1.00 0.69 D
A3P 1/4-18 NPTF 1.63 0.63 0.56
B
RD704L† RD704LSL 9/16-18 1.92 1.00 0.69 A4L† 9/16-18 1.50 0.63 0.56
HEX HEX
RD705 RD705SL 3/8-18 NPTF 1.99 1.00 0.69
TWO-WAY
Part No. - Brass Thread Dimensions Female End Connections Part No. Dimensions
Standard Acetyl. Serv. Size A B HEX A C
Brass Thread Size C D HEX
RD700 RD700SL 1/8-27 NPTF 1.73 1.00 0.69 A2 1/4-18 NPTF 1.46 0.77 0.69
RD702 RD702SL 1/4-18 NPTF 1.95 1.00 0.69 B D A5L‡ 9/16-18 1.38 0.77 0.69
RD704 RD704SL 3/8-18 NPTF 2.03 1.00 0.69 HEX HEX
RD705L‡ RD705LSL 9/16-18 1.95 1.00 0.69
Part No. - Brass Hose Dimensions Hose Stem End Connections Part No. Dimensions
STRAIGHT-THRU
Standard Acetyl. Serv. I.D. A B A Brass Hose I.D. C D
RD706 RD706SL 1/4" 2.47 1.00 C A7 1/4" 2.06 0.56
RD706P§ — 1/4" 2.24 1.00 B D A8 5/16" 2.06 0.56
RD707 RD707SL 5/16" 2.47 1.00 A9 3/8" 2.10 0.56
RD708 RD708SL 3/8" 2.47 1.00
RD708P —
RD-706P RD-708P
Part No. - Brass Hose Dimensions Hose Clamp End Connections Part No. Hose Dimensions
Standard Acetyl. Serv. I.D. O.D. A B HEX Brass I.D. O.D. C D HEX
RD70B3 RD70B3SL 1/4" 1/2" 2.56 1.00 0.63 A C 7B3 1/4" 1/2" 2.19 0.70 0.63
RD70B7 — 1/4" 5/8" 2.56 1.00 0.75 7B7 1/4" 5/8" 2.19 0.84 0.75
RD70D7 — 3/8" 5/8" 2.68 1.00 0.75 B D 7B11 1/4" 3/4" 2.19 0.98 0.88
RD70D9 — 3/8" 11/16" 2.68 1.00 0.81 HEX HEX
RD70D11 — 3/8" 3/4" 2.68 1.00 0.88
GAS
† L.H. Thread - 30° Female Flare ‡ L.H. Thread - Inverted Flare § For use with push-on style hose.
Series 700 couplings are not to be used with

acetylene at pressures exceeding 15 psig.
ACCESSORIES
Coupling Series Plug Dust Cap Part No. Socket Dust Plug Part No.
600 PPDC1HK PSDC1HK
700 PPDC1HK PSDC1HK
Vinyl Socket Dust Plug
Vinyl Plug Dust Cap
29
1/4” Nominal
2RL & 3RL Series
Interchangeability
Materials
Socket:
• Zinc Plated Steel Body
• Brass Socket End
• Nickel Plated Steel Sleeve
• Stainless Steel Spring
• Zinc Plated Steel Locking Ring
2RL & 3RL Ring Lock quick connect Plug:
couplings have a unique interchange which Eaton • Zinc Plated Case-Hardened Steel
designed for use with compressed air. Body sizes
are 1/4" and 3/8". 1/4" to 3/8" nominal
(6.35 mm to 9.52 mm)
F eatures
• High flow capacity -40° F to 250° F

• Push to connect -40° C to 120° C
• Ring lock
• Will not disconnect when hose is dragged on the ground Rated Pressure
• Rotate locking sleeve approximately 20° to disconnect Series Size PSI BAR
2RL 1/4" 300 20
• Optional seal materials available 3RL 3/8" 300 20

Flow Capacity
• Shipyards Series † Ac † Air flow (scfm)
with 5 psi pressure
• General Pneumatics 2RL 48 drop and 100 psig
3RL 80 inlet pressure.
• Mining
• Marine
30
1/4” Nominal
2RL Series
SOCKETS PLUGS
Male End Connections Dimensions
Dimensions Part No.
2R10 1/8-27 NPTF 2.01 1.06 0.88 2L10 1/8-27 NPTF 1.51 0.58 0.50
2R15 1/4-18 NPTF 2.16 1.06 0.88 2L15 1/4-18 NPTF 1.66 0.65 0.56
3/8-18 NPTF 2.16 1.06 0.88 2L15G† 1/4-18 NPTF 2.64 0.77 0.69
ONE-WAY
2R20
2R25 1/2-14 NPTF 2.35 1.06 0.88 2L20 3/8-18 NPTF 2.04 0.79 0.69
2L20G† 3/8-18 NPTF 2.64 0.77 0.69
2L25 1/2-14 NPTF 2.31 1.01 0.88

2R11 1/8-27 NPTF 1.91 1.06 0.88 2L11 1/8-27 NPTF 1.36 0.65 0.56
2R16 1/4-18 NPTF 1.91 1.06 0.88 2L16 1/4-18 NPTF 1.54 0.79 0.69
2R21 3/8-18 NPTF 2.16 1.06 0.88 2L16G† 1/4-18 NPTF 2.55 0.77 0.69
2R26 1/2-14 NPTF 2.43 1.06 1.00 2L21 3/8-18 NPTF 1.88 0.94 0.81
2L26 1/2-14 NPTF 2.18 1.15 1.00
TWO-WAY
2R17 1/4" 2.63 1.06 2L17 1/4" 2.13 0.56
2R195 5/16" 2.63 1.06 2L195 5/16" 2.13 0.56
2R22 3/8" 2.63 1.06 2L22 3/8" 2.13 0.56
2R27 1/2" 2.63 1.06 2L27 1/2" 2.50 0.81
STRAIGHT-THRU
2R18B1 1/4" 15/32" 2.73 1.06 0.63 2L18B3 1/4" 1/2" 2.23 0.70 0.63
2R18B3 1/4" 1/2" 2.73 1.06 0.63 2L185C7 5/16" 5/8" 2.29 0.84 0.75
2R18B7 1/4" 5/8" 2.73 1.06 0.75 2L185C9 5/16" 11/16" 2.29 0.91 0.81
2R18B11 1/4" 3/4" 2.73 1.06 0.88 2L23D5 3/8" 9/16" 2.35 0.77 0.69
2R185C7 5/16" 5/8" 2.79 1.06 0.75 2L23D7 3/8" 5/8" 2.35 0.84 0.75
2R185C9 5/16" 11/16" 2.79 1.06 0.81 2L23D9 3/8" 11/16" 2.35 0.91 0.81
2R23D7 3/8" 5/8" 2.85 1.06 0.75 2L23D11 3/8" 3/4" 2.35 0.98 0.88
2R23D9 3/8" 11/16" 2.85 1.06 0.81 2L23D13 3/8" 13/16" 2.35 1.05 0.94
2R23D11 3/8" 3/4" 2.85 1.06 0.88 2L28P13 1/2" 13/16" 3.41 1.05 0.94
2R23D13 3/8" 13/16" 2.85 1.06 0.94 2L28P15 1/2" 7/8" 3.41 1.12 1.00
2R28P13 1/2" 13/16" 3.48 1.06 0.94
2R28P15 1/2" 7/8" 3.48 1.06 1.00
GAS
† With Bleeder Ball Check – Reduces hose whip when disconnecting.

ACCESSORIES
Vinyl Dust Plug

2RL PPDC1HK PSDC1HK
3RL PPDC2HK PSDC2HK
Vinyl Dust Cap
31
3/8” Nominal
3RL Series
SOCKETS PLUGS
3R15 1/4-18 NPTF 2.34 1.31 1.00 3L10 1/8-27 NPTF 1.54 0.72 0.63
3R20 3/8-18 NPTF 2.35 1.31 1.00 3L15 1/4-18 NPTF 1.70 0.72 0.63
3R25 1/2-14 NPTF 2.54 1.31 1.00 3L15G† 1/4-18 NPTF 2.64 0.98 0.88
3R30 3/4-14 NPTF 2.54 1.31 1.06 3L20 3/8-18 NPTF 1.76 0.79 0.69
3L20G† 3/8-18 NPTF 2.64 0.98 0.88
3L25 1/2-14 NPTF 2.31 1.01 0.88
3L25G† 1/2-14 NPTF 2.83 0.98 0.88
3L30 3/4-14 NPTF 2.38 1.23 1.06
3L30G† 3/4-14 NPTF 2.88 1.19 1.06

3R16 1/4-18 NPTF 2.29 1.31 1.00 3L16 1/4-18 NPTF 1.48 0.79 0.69
3R21 3/8-18 NPTF 2.35 1.31 1.00 3L16G† 1/4-18 NPTF 2.39 0.98 0.88
3R26 1/2-14 NPTF 2.63 1.31 1.00 3L21 3/8-18 NPTF 1.63 0.94 0.81
3R31A 3/4-14 NPTF 2.66 1.31 1.19 3L21G† 3/8-18 NPTF 2.64 0.98 0.88
3L26 1/2-14 NPTF 2.25 1.15 1.00
3L26G† 1/2-14 NPTF 2.91 0.98 0.88
3L31 3/4-14 NPTF 2.25 1.37 1.19

3R17 1/4" 2.82 1.31 3L17 1/4" 2.16 0.63
3R195 5/16" 2.85 1.31 3L195 5/16" 2.16 0.63
3R22 3/8" 2.89 1.31 3L195G† 5/16" 3.11 0.98
3R27 1/2" 2.81 1.31 3L22 3/8" 2.16 0.75
3R32 3/4" 3.66 1.31 3L22G† 3/8" 3.11 0.98
3L27 1/2" 2.16 0.81
3L27G† 1/2" 3.11 0.98
3L32 3/4" 3.13 1.00
3L32G† 3/4" 3.96 0.98
3R23D7 3/8" 5/8" 3.06 1.31 0.75 3L23D7 3/8" 5/8" 2.45 0.84 0.75
3R23D9 3/8" 11/16" 3.06 1.31 0.81 3L23D9 3/8" 11/16" 2.45 0.91 0.81
3R23D11 3/8" 3/4" 3.06 1.31 0.88 3L23D11 3/8" 3/4" 2.45 0.98 0.88
3R28P13 1/2" 13/16" 3.66 1.31 0.94 3L28P13 1/2" 13/16" 3.14 1.05 0.94
3R28P15 1/2" 7/8" 3.66 1.31 1.00 3L28P15 1/2" 7/8" 3.14 1.12 1.00
3R33R23 3/4" 1⅛" 3.79 1.40 1.25 3L33R23 3/4" 11/8" 3.56 1.40 1.25
3R33R25 3/4" 13/16" 3.79 1.47 1.31 3L33R25 3/4" 13/16" 3.56 1.47 1.31
† With Bleeder Ball Check – Reduces hose whip when disconnecting.
Optional Seal Materials: 143-Fluorocarbon
32
Full-Bore Series
ONE-WAY
Interchangeability
All Sizes 1/2" only
Materials
Socket:
• Carbon Steel
• Hard Drawn Steel Spring
• Buna-N Valve
TWO-WAY
• Stainless Steel Locking Balls
The Full-Bore Series is a premium automatic Plug:
one-way shutoff coupling. Two sleeves must be actuated • Carbon Steel
in sequence to bleed off back pressure and release the
connector, preventing accidental uncoupling. Available in (9.52 mm to 12.70 mm)
3/8" and 1/2" capacities.
-40° F to 200° F
STRAIGHT-THRU
F eatures -40° C to 93° C
• Pressure relieving feature fully vents downstream air, making
Rated Pressure
connection/disconnection fast and easy, and eliminating hose
whip 250 psig (17 Bar)
• Unique straight-through design eliminates restrictive springs
and poppet valves, allowing unimpeded air flow Flow Capacity
† Air flow (scfm)
Size Ac †
• Two-sleeve activation prevents accidental disconnect 3/8" 63
with 5 psig
pressure drop
1/2" 101 and 100 psig inlet
A pplications & markets pressure.
• Construction • Railyards PRESSURE DROP VS. AIR FLOW

• Maintenance & Repair • General Pneumatics 10.0
20
• In-Plant/Industrial
GAS
5.0
PRESSURE DROP, psid
10
PRESSURE DROP, psid
1.0
3
2
ACCESSORIES
1
10 20 30 50 70 100 200 300
AIR FLOW, scfm (100 psig Inlet Pressure)
0.1
1 10 100 1,000
AIR FLOW, scfm
3/8" Full-Bore
1/2" Full-Bore
33
Full-Bore Series
3/8" SOCKETS PLUGS

Steel Thread Size A B HEX A Steel Thread Size C D HEX
23203013 3/8" NPT 3.80 1.25 1.00 C
40 1/4" NPT 1.88 0.72 0.63
23203014 1/2" NPT 2.80 1.25 1.00 B D 42 3/8" NPT 1.88 0.79 0.69
44 1/2" NPT 2.09 1.01 0.88
HEX HEX

C
23203300 3/8" NPT 3.17 1.25 1.00 41 1/4" NPT 1.63 0.79 0.69
23203004 1/2" NPT 3.92 1.25 1.00 B D 43 3/8" NPT 1.81 0.94 0.81
45 1/2" NPT 2.06 1.15 1.00
HEX HEX
Steel Hose I.D. A B A
Steel Hose I.D. C D
23203024 3/8" 4.36 1.25 C 404 1/4" 2.34 0.63
23203025 1/2" 4.48 1.25 B D
406 3/8" 2.34 0.63
408 1/2" 2.34 0.81
1/2" SOCKETS PLUGS

Steel Thread Size A B HEX A
23204014 1/2" NPT 4.43 1.38 1.13 C 52 3/8" NPT 2.25 0.87 0.75
23204015 3/4" NPT 4.67 1.38 1.13 B D 54 1/2" NPT 2.44 1.01 0.88
56 3/4" NPT 2.50 1.23 1.06
HEX HEX

A
Steel Thread Size A B HEX C
23204400 1/2" NPT 3.31 1.38 1.13 53 3/8" NPT 2.06 0.94 0.81
23204005 3/4" NPT 3.30 1.38 1.13 B D
55 1/2" NPT 2.34 1.15 1.00
57 3/4" NPT 2.44 1.37 1.19
HEX HEX
Steel Hose I.D. C D
23204025 1/2" 4.15 1.38 C 59 3/8" 2.66 0.69
23204026 3/4" 4.15 1.38 B D 60 1/2" 2.66 0.75
61 3/4" 3.50 1.00
34
ARO 210/310 Interchange
210 & 310 Series
ONE-WAY
Interchangeability
- ARO Interchange
Materials
Socket:
• Carbon Steel
• Hard Drawn Steel Springs
• Buna-N Valve Washer
• Alloy Steel Locking Pins
Plug:
TWO-WAY
• Carbon Steel
The 210 and 310 Interchange Series 1/4" to 3/8" nominal
are 1/4" and 3/8" capacity automatic, pin-type couplings (6.35 mm to 9.52 mm)
designed for one-way shutoff operation.
-40° F to 200° F
F E AT U R E S -40° C to 93° C
• Automatic push-to-connect
STRAIGHT-THRU
• Pin-lock design Rated Pressure
250 psig (17 Bar)
• Construction Flow Capacity † Air flow (scfm)
• Maintenance & Repair Series Ac † with 5 psig
pressure drop
• In-Plant/Industrial 210 19
and 100 psig inlet
310 50
• Pneumatic Tools pressure.
PRESSURE DROP VS. AIR FLOW

10.0
5.0
GAS
PRESSURE DROP, psid
1.0
ACCESSORIES
0.1
1 10 100
AIR FLOW, scfm
210 Series
310 Series
35
ARO 210/310 Interchange
210 & 310 Series
210 SERIES SOCKETS PLUGS

210212 1/4" NPT 1.95 1.02 0.69 C 2607 1/8-27 NPTF 1.42 0.58 0.50
210213 3/8" NPT 1.91 1.02 0.69 2608 1/4-18 NPTF 1.68 0.65 0.56
B D
2608B 1/4-19 BSPT 1.68 0.65 0.56
HEX HEX
20AP37M 3/8-18 NPTF 1.68 0.79 0.69

C
210 1/4" NPT 1.87 1.02 0.69 2609 1/4-18 NPTF 1.55 0.79 0.69
62210* 1/4" NPT 1.87 1.02 0.69 B D 2609B 1/4-19 BSPP 1.55 0.79 0.69
20AP37F 3/8-18 NPTF 1.61 0.94 0.81
HEX HEX
Steel Hose I.D. C D
C 3946 1/4" 2.14 0.50
210022 1/4" 2.39 1.02
210215 3/8" 2.39 1.02 B D 3947 5/16" 2.14 0.50
22238 3/8" 2.14 0.50
* Same as Model 210 but with brass valve
310 SERIES SOCKETS PLUGS

Steel Thread Size D E HEX
310313 3/8" NPT 2.38 1.21 0.94 C 22239 1/4" NPT 1.91 0.72 0.63
3804 3/8" NPT 1.91 0.79 0.69
B
HEX HEX

Steel Thread Size A B HEX A Steel Thread Size D E HEX
310 3/8" NPT 2.10 1.21 0.94 C 3806 3/8" NPT 1.84 0.94 0.81
B D
HEX HEX
Steel Hose I.D. C D
310222 3/8" 2.97 1.21 C 3807 3/8" 2.37 0.63
B D
36
MS Series
ONE-WAY
Interchangeability
- Industrial Interchange
- A-A-59439 (former MIL-C-4109)
Materials
Socket:
• Carbon Steel
• Hard Drawn Steel Springs
• Buna-N Valve Washer
• Alloy Steel Locking Pins
TWO-WAY
Plug:
The MS Series is an economical automatic one- • Carbon Steel
way shutoff coupling. With steel pins securing the mating
connector, the MS Series is available in 1/4" capacity.
-40° F to 200° F
F E AT U R E S -40° C to 93° C
• Automatic push-to-connect
STRAIGHT-THRU
• Pin-lock design Rated Pressure
250 PSIG (17 Bar)
• Construction † Air flow (scfm)
Flow Capacity with 5 psig
• Maintenance & Repair Series Ac † pressure drop
MS 26 and 100 psig inlet
• In-Plant/Industrial pressure.
• Pneumatic Tools
PRESSURE DROP VS. AIR FLOW
10.0
5.0
PRESSURE DROP, psid
GAS
1.0
ACCESSORIES
0.1
1 10 100
AIR FLOW, scfm
37
MS Series
SOCKETS PLUGS

C
MSCM22000 1/4" NPT 1.95 1.02 0.69 10 1/4" NPT 1.75 0.65 0.56
MSCM23000 3/8" NPT 1.91 1.02 0.69 B D 12 1/8" NPT 1.59 0.58 0.50
14 3/8" NPT 1.75 0.79 0.69
HEX HEX

Steel Thread Size A B HEX A C Steel Thread Size C D HEX
MSCF22000 1/4" NPT 1.95 1.02 0.69 11 1/4" NPT 1.63 0.79 0.69
MSCM23000 3/8" NPT 1.95 1.02 0.69 B D 13 1/8" NPT 1.47 0.65 0.56
15 3/8" NPT 1.69 0.94 0.81
HEX HEX
Steel Hose I.D. A B A Steel Hose I.D. C D
C
MSCH22000 1/4" 2.39 1.02 16 1/4" 2.22 0.50
MSCH23000 3/8" 2.39 1.02 B D 17 3/8" 2.22 0.50
Also interchanges with 1000 Series plugs on page 10.
38
TWO-
WAY
ONE-WAY
TWO-WAY
STRAIGHT-THRU
GAS
ACCESSORIES
39
eaton Quick Disconnect Couplings E-MEQD-MC001-E2
TWO-WAY
Coupling Locking
Body Size Body Material Options
Style Mechanism
STEEL (Zinc/chromate Finish)

MINIMUM SPILL INCLUSION

STAINLESS STEEL (303)
PLASTIC (Polypropylene)
MANUAL CONNECT
THREADED SLEEVE
PUSH-TO-CONNECT
PLASTIC FINGERS
DUST CAP/PLUG
SLEEVE LOCK
BALL LOCK
1/8 INCH
1/4 INCH
3/8 INCH
1/2 INCH
3/4 INCH
1¼ INCH
1½ INCH
2½ INCH
BRASS
1 INCH
Coupling
Series Page
1HK 41-43 ● ● ● ● ● ● ● ● ● ●
2HK 41-43 ● ● ● ● ● ● ● ● ● ●
P2HK 41-43 ● ● ● ● ● ●
3HK 41-43 ● ● ● ● ● ● ● ● ● ●
4HKP 41-43 ● ● ● ● ● ● ● ● ● ●
6HKP 41-43 ● ● ● ● ● ● ● ● ● ●
8HKP 41-43 ● ● ● ● ● ● ● ● ● ●
10HK 44-46 ● ● ● ● ● ● ● ●
12HK 44-46 ● ● ● ● ● ● ● ● ●
20HK 44-46 ● ● ● ● ● ● ● ● ●
HKFR 47 ● ● ● ● ● ● ● H ●
HA15000 48/49 ● ● ● ● ● ● ● ● ●
FF 50-52 ● ● ● ● ● ● ● ● ● H ● ●
5100 53 ● ● ● ● ● ● ● ●
UP10 54/55 ● ● ● ● H ●
WA56000 56 ● ● ● ● ●
2HKIG 58 ● ● ● ● ● ●
2HKIL 59 ● ● ● ● ●
DB 59 ● ● ● ● ● ●
H Sleeve Lock is Standard
40
Hydraulic Couplings
HK 1-8 Series
ONE-WAY
Interchangeability
- ISO 7241-1 Series B
Materials
• Brass, zinc-plated steel, stainless steel
or polypropylene (¼" only) construction
• Stainless steel springs, balls and
retaining rings
• Buna-N (Nitrile) seals
• PTFE back-up rings in steel and
TWO-WAY
stainless steel sockets
Series HK Couplings are the most versatile
couplings available and are suitable for use with various 1/8" to 1" nominal
(4.4 mm to 25.4 mm)
liquids, chemicals, steam, gases and vacuum. Series HK
couplings conform to the dimensional requirements of
-40° F to 250° F
ISO 7241-1 Series B. Body sizes range from 1/8" to 1".
-40° C to 121° C
(with standard seal)
F eatures
STRAIGHT-THRU
• The coupling that set the industry standard Rated Pressure Chart
• Multiple options make the HK our most versatile coupling
Part Body Size Brass Steel Stainless Steel
series available Number inches (mm) PSI BAR PSI BAR PSI BAR
• Brass, steel and stainless steel construction available in all 1HK 1/8 (4.4) 3,000 207 4,000 275 5,000 344
sizes; 1/4" body size is also available in polypropylene 2HK 1/4 (5.9) 2,700 186 5,000 345 3,700 255
3HK 3/8 (7.8) 2,200 152 3,700 255 3,700 255
• End connections are female NPTF, BSPP and SAE o-ring boss 4HKP 1/2 (10) 2,250 155 5,000 345 4,250 293
6HKP 3/4 (17) 2,000 138 4,000 275 3,500 242
• Heavy duty steel couplings for use in high impulse service 8HKP 1 (19.6) 1,500 103 4,000 275 3,000 207
available in most sizes Part Body Size Polypropylene
Number inches (mm) PSI Temperature Range
• Steam coupling available in 3/8" body size BAR
P2-HK 1/4 (5.9) 50 4 +35° F to 150° F
GAS
• Agriculture • Military • HVAC Flow Capacity
• Hydraulic Tool • Law Enforcement/ • Food and
• General Industry Rescue Beverage
• Construction • Chemical • Trucks
• Fluid Transfer • Oil and Gas • Aerospace
• Transportation • Consumer Products • Medical

ACCESSORIES
41
Hydraulic Couplings
HK 1-8 Series
Socket Plug
SOCKETS
Body Part Number Thread Size (female) Dimensions (inches)
Size Steel Stainless Steel Across
(inch) Brass NPTF BSPP SAE A B
Standard High Impulse 303 316 Flats
1/8 B1H11 1H11 — LL1H11 ML1H11 1/8-27 — — 1.91 0.98 0.56
1/8 — 1H4 — LL1H4 — — — 7/16-20 2.06 0.98 0.69
1/4 B2H16 2H16 2H16 LL2H16 ML2H16 1/4-18 — — 2.26 1.14 0.75
1/4 B2H16BS 2H16BS 2H16BS LL2H16BS ML2H16BS — 1/4-19 — 2.31 1.14 0.75
1/4 — 2H6 2H6 LL2H6 — — — 9/16-18 2.40 1.14 0.88
3/8 B3H21 3H21 3H21C LL3H21 ML3H21 3/8-18 — 2.56 1.42 0.88
3/8 B3H21BS 3H21BS — LL3H21BS ML3H21BS — 3/8-19 — 2.56 1.42 0.88
3/8 — 3H8 3H8C LL3H8 — — — 3/4-16 2.74 1.42 1.00
1/2 B4HP26 4HP26 4HP26 LL4HP26 ML4HP26 1/2-14 — — 2.96 1.86 1.13
1/2 B4HP26BS 4HP26BS 4HP26BS LL4HP26BS ML4HP26BS — 1/2-14 — 2.96 1.86 1.13
1/2 — 4HP10 4HP10 LL4HP10 — — — 7/8-14 3.05 1.86 1.25
3/4 B6HP31 6HP31 6HP31 LL6HP31 ML6HP31 3/4-14 — — 3.48 2.22 1.31
3/4 B6HP31BS 6HP31BS 6HP31BS LL6HP31BS ML6HP31BS — 3/4-14 — 3.48 2.22 1.31
3/4 — 6HP12 6HP12 LL6HP12 — — — 11/16-12 3.67 2.22 1.38
1 B8HP36 8HP36 8HP36 LL8HP36 ML8HP36 1-111/2 — — 4.13 2.61 1.75
1 B8HP36BS 8HP36BS 8HP36BS LL8HP36BS ML8HP36BS — 1-11 — 4.13 2.61 1.75
1 — 8HP16 8HP16 LL8HP16 — — — 15/16-12 4.13 2.61 1.88
A = Overall Length B = Maximum Diameter
PLUGS
Body Part Number Thread Size (female) Dimensions (inches)
Size Steel Stainless Steel
Brass NPTF BSPP SAE C D E HEX
(inch) Standard High Impulse 303 316
1/8 B1K11 1K11 — LL1K11 ML1K11 1/8-27 — — 1.26 0.65 0.44 0.56
1/8 — 1K4 — LL1K4 — — — 7/16-20 1.41 0.79 0.59 0.69
1/4 B2K16 2K16 2K16C LL2K16 ML2K16 1/4-18 — — 1.52 0.87 0.56 0.75
1/4 B2K16BS 2K16BS — LL2K16BS ML2K16BS — 1/4-19 — 1.52 0.87 0.56 0.75
1/4 — 2K6 2K6C LL2K6 — — — 9/16-18 1.66 1.01 0.70 0.88
3/8 B3K21 3K21 3K21C LL3K21 ML3K21 3/8-18 — 1.76 1.01 0.61 0.88
3/8 B3K21BS 3K21BS — LL3K21BS ML3K21BS — 3/8-19 — 1.76 1.01 0.61 0.88
3/8 — 3K8 3K8C LL3K8 — — — 3/4-16 1.94 1.15 0.79 1.00
1/2 B4KP26 4KP26 4KP26 LL4KP26 ML4KP26 1/2-14 — — 2.03 1.30 0.76 1.13
1/2 B4KP26BS 4KP26BS 4KP26BS LL4KP26BS ML4KP26BS — 1/2-14 — 2.03 1.30 0.76 1.13
1/2 — 4KP10 4KP10 LL4KP10 — — — 7/8-14 2.11 1.37 0.84 1.19
3/4 B6KP31 6KP31 6KP31 LL6KP31 ML6KP31 3/4-14 — — 2.36 1.52 0.71 1.31
3/4 B6KP31BS 6KP31BS 6KP31BS LL6KP31BS ML6KP31BS — 3/4-14 — 2.36 1.52 0.71 1.31
3/4 — 6KP12 6KP12 LL6KP12 — — — 11/16-12 2.54 1.59 0.89 1.38
1 B8KP36 8KP36 8KP36 LL8KP36 ML8KP36 1-111/2 — — 2.85 1.88 0.97 1.63
1 B8KP36BS 8KP36BS 8KP36BS LL8KP36BS ML8KP36BS — 1-11 — 2.85 1.88 0.97 1.63
1 — 8KP16 8KP16 LL8KP16 — — — 15/16-12 2.85 2.17 0.97 1.88
C = Overall Length D = Maximum Diameter E = Exposed Length when Connected

Vinyl Dust Plug
Coupling Series
Metal Vinyl Metal Vinyl
1HK PDC1HK* PPDC1HK SDC1HK* PSDC1HK Vinyl Dust Cap
2HK PDC2HK* PPDC2HK SDC2HK* PSDC2HK
3HK PDC3HK* PPDC3HK SDC3HK* PSDC3HK
Metal Dust Cap
4HK PDC4HK** PPDC4HK SDC4HK** PSDC4HK
6HK PDC6HK** PPDC6HK SDC6HK** PSDC6HK
8HK PDC8HK** PPDC8HK SDC8HK** PSDC8HK Metal Dust Plug
* Brass ** Aluminum
42
Hydraulic Couplings
HK 1-8 Series
O ptions
• Non-valved socket and plug • Bleeder-style plug • Seals: PTFE, Neoprene, Flourocarbon, Buna-N, EPDM
• Valve actuator in socket or plug • Sleeve lock and Kalrez (see Elastomer Selection Guide, page 82)
ONE-WAY
Series P2HK Plastic Coupling
The Series P2-HK coupling is intended for use with air, water and various chemicals at low pressure. It is designed for use where an
economical, light weight, corrorion resistant coupling is desired. All components, except springs and seals, are molded from natural
polypropylene with a UV inhibitor. Valve springs are 316 stainless steel. Fluorocarbon seals are standard. EPDM seals are optional.
Socket Plug
Thread Size Dimensions Thread Size Dimensions

Part No. NPTF A B HEX Part No. NPTF C D E HEX
PP2H25F 1/4-18 2.38 1.45 0.88 PP2K25F 1/4-18 1.65 1.01 0.67 0.88
TWO-WAY
E = Exposed length when connected
Series 3HK Steam Coupling

The steam coupling has a large diameter flange on the sleeve to aid gripping while the user wears heavy gloves. EPDM seals are standard,
and can be used with steam at temperatures up to 350°F. Options are BSPP threads, sleeve lock, EPDM seals for use with steam at
temperatures above 350°F and fluorocarbon seals.
Socket Plug
Dimensions Thread Size Dimensions
STRAIGHT-THRU
Thread Size Across Part No. NPTF C D E HEX
Part No. NPTF A B Flats B3K21192 3/8-18 1.76 1.01 0.61 0.88
B3H21Y 3/8-18 2.56 1.75 0.88
E = Exposed length when connected
Release Clamp with Chain

When fluid lines may be subjected to a damaging pull, couplings can be mounted
Series Kit Part No.
to disconnect automatically, sealing both ends of a line against fluid loss. The 1HK 1HRCK
socket sleeve can be anchored to a stationary bracket, either directly or with a 2HK 2HRCK
3HK 3HRCK
chain. Excessive pull on the plug end of the line moves the socket body forward 4HKP 4HRCK
relative to the sleeve, and the plug is released without damage to the line. Release 6HKP 6HRCK
8HKP 8HRCK
Clamp Assembly Kits are available for Series 1HK through 8HKP sockets.
GAS
Bleeder-Style Plugs & One-Way Shut-Off Conversion Via (VAA) Series Plug Part No. Valve Actuator
1HK B1K11VB B1K11VAA
Bleeder-style plugs can be used on air lines to prevent hose whip when disconnecting a line by
2HK B2K16VB B2K16VAA
reducing the exhaust velocity of air. Bleeder-style plugs can be used on hydraulic lines to prevent 2HK 2K16CVB 2K16CVAA
static pressure from building up in disconnected lines. Valves of these plugs are manufactured 3HK B3K21VB B3K21VAA
3HK 3K21VB 3K21VAA
such that a small leak path exists when the plug is disconnected. Bleeder-style plugs are available 3HK 3K21CVB 3K21CVAA
ACCESSORIES
in Series 1HK through 6HKP. 4HKP 4KP26VB 4KP26VAA

6HKP B6KP31VB B6KP31VAA
Typical use of 6HKP 6KP31VB 6KP31VAA
VAA option with
series HK
43
Hydraulic Couplings
HK 10/12/20 Series
Interchangeability
- ISO 7241-1 Series B*
Materials
• Brass, zinc-plated steel or stainless
steel construction
retaining rings
1-1/4" to 2-1/2" nominal

(31.75 mm to 63.5 mm)
Series 10-20 HK Couplings have the same
features as the 1-8 HK, but have larger bodies and higher
-40° F to 250° F
flow rates. Series HK couplings conform to the dimensional
-40° C to 121° C
requirements of ISO 7241-1 Series B*. Body sizes range (with standard seal)
from 1¼" to 2½".
Rated Pressure
F eatures
• Brass, steel and stainless steel construction available in all Part Body Size Brass Steel Stainless Steel
sizes Number inches (mm) PSI BAR PSI BAR PSI BAR
• End connections are female NPTF and BSPP 10HK 1¼ (31.8) 1,200 83 1,700 118 1,700 118
12HK 1½ (38.1) 1,500 104 2,200 152 2,200 152
• Heavy duty steel couplings for use in high impulse service
available in 12 HK and 20 HK 20HK 2½ (63.5) 700 49 1,500 104 1,500 104
A pplications & M A R K E T S
• Agriculture Flow Capacity
• Hydraulic Tool
• General Industry
• Construction
• Fluid Transfer
• Chemical
• Oil and Gas
• Transportation
• Food and
Beverage
• Trucks
• Nuclear
* No ISO Standard available for the 10HK.
44
Hydraulic Couplings
HK 10/12/20 Series
ONE-WAY
Socket Plug
SOCKETS
Part Number Thread Size (female) Dimensions (inches)
Body
Size Steel 303 Stainless
(inch) Brass NPTF BSPP A B HEX
Standard High Impulse Steel
1¼* B10H41 10H41 — LL10H41 1¼-11½ — 4.51 2.73 2.38
1¼* — 10H41BS — LL10H41BS — 1¼-11 4.51 2.73 2.38
1½ B12H41 12H41 12H41C LL12H41 1¼-11½ — 4.82 3.23 2.38
1½ B12H41BS 12H41BS 12H41CBS LL12H41BS — 1¼-11 4.82 3.23 2.38
TWO-WAY
1½ B12H46 12H46 12H46C LL12H46 1½-11½ — 4.82 3.23 2.38
1½ B12H46BS 12H46BS 12H46CBS LL12H46BS — 1½-11 4.82 3.23 2.38
2½ B20H51 20H51 20H51 LL20H51 2-11½ — 5.55 4.11 3.75
2½ B20H51BS 20H51BS 20H51BS LL20H51BS — 2-11 5.55 4.11 3.75
2½ B20H56 20H56 20H56 LL20H56 2½-8 — 6.14 4.11 3.75
2½ B20H56BS 20H56BS 20H56BS LL20H56BS — 2½-11 6.14 4.11 3.75
2½ B20H61 20H61 20H61 LL20H61 3-8 — 7.00 4.11 4.00
2½ B20H61BS 20H61BS 20H61BS LL20H61BS — 3-11 7.00 4.11 4.00
A = Overall Length B = Maximum Diameter
STRAIGHT-THRU
PLUGS
Part Number Thread Size (female) Dimensions (inches)
Body Size Steel
(inch) 303 Stainless
Brass NPTF BSPP C D E HEX
Standard High Impulse Steel
1¼* B10K41 10K41 — LL10K41 1¼-11½ — 4.25 2.74 2.33 2.38

1¼* — 10K41BS — LL10K41BS — 1¼-11 4.25 2.74 2.33 2.38
1½ B12K41 12K41 12K41C LL12K41 1¼-11½ — 4.76 — 2.67 2.38
1½ B12K41BS 12K41BS 12K41CBS LL12K41BS — 1¼-11 4.76 2.74 2.67 2.38
1½ B12K46 12K46 12K46C LL12K46 1½-11½ — 4.76 2.74 2.67 2.38
1½ B12K46BS 12K46BS 12K46CBS LL12K46BS — 1½-11 4.76 2.74 2.67 2.38
2½ B20K51 20K51 20K51C LL20K51 2-11½ — 5.49 4.33 2.97 3.75
2½ B20K51BS 20K51BS 20K51CBS LL20K51BS — 2-11 5.49 4.33 2.97 3.75
GAS
2½ B20K56 20K56 20K56C LL20K56 2½-8 — 6.08 4.33 3.56 3.75
2½ B20K56BS 20K56BS 20K56CBS LL20K56BS — 2½-11 6.08 4.33 3.56 3.75
2½ B20K61 20K61 20K61C LL20K61 3-8 — 6.94 4.62 4.42 4.00
2½ B20K61BS 20K61BS 20K61CBS LL20K61BS — 3-11 6.94 4.62 4.42 4.00

* ISO 7241-1 Series B does not include 1-1/4 inch body size couplings; therefore, Series 10HK is not covered by this standard ACCESSORIES

12HK PDC12HK* SDC12HK*
20HK PDC20HK* SDC20HK*
*Aluminum
Metal Dust Cap Metal Dust Plug
45
Hydraulic Couplings
HK 1-20 Series
special ordering instructions F O R H K S E R I E S
How to build a socket or plug part number with options:
Example: 4HP26 - VAA - SL - 143
Standard Part Number Seal Material:

from Part Number Tables 115 = PTFE4
118 = Neoprene
NV = No Valve1 143 = Fluorocarbon
VAA = Valve Actuator Assembly2 146 = Buna-N5
VB = Bleeder Valve (Plugs Only)3 192 = EPDM6
235 = Kalrez
SL = Sleeve Lock (Sockets Only) 236 = EPDM (350°F+ Steam)6
Notes:
1) The NV option should be specified for a socket and a plug when a non-valved coupling is
desired. Non-valved Series 1HK through 8HKP plugs do not contain seals. Do not specify a seal
material.
2) The VAA option should be specified for either a socket or a plug when a one-way coupling is
desired. (Not available for series 10HK)
3) The VB option can be ordered for Series 1HK through 6HKP plugs to prevent pressure build-up
in disconnected hydraulic lines or to reduce hose whip when disconnecting pneumatic lines.
4) Series HK couplings are designed for use with elastomer seals. PTFE is not an elastomer. It is
rigid and not resilient. Couplings with PTFE seals may leak and/or be difficult to connect. Force
to connect may be reduced by heating connected couplings in hot water; then, cooling before
disconnecting. PTFE seals are available for Series 1-HK through 8-HKP, except Series P2-HK.
5) The 146 seal option may be specified for fuels and hydraulic fluids that are known to cause
standard Buna-N seals to swell excessively.
6) The 236 EPDM seal option should be ordered for use with steam at or above 350° F. The 192
EPDM seal option should be ordered for hot water above 180° F and steam below 350° F.
7) Some part numbers may be subject to minimum order quantities and/or available only by special
quotation. Consult your local distributor.
8) High Impulse – The high strength steel and heat treatment used to give increased resistance to
“brinelling” (indentations by locking balls in the plug groove).
46
BOP Safety Coupling
HKFR Series
ONE-WAY
Interchangeability
- ISO 7241-1 Series B
Materials
• Steel
• Stainless Steel (ML8HFR36)
1/2" to 1" nominal

(12.7 mm to 25.4 mm)
TWO-WAY
Certified to 1300° F (700° C)
The HKFR Series is a quick disconnect, hydraulic (see Lloyd’s Register Cerification below)
coupling, that is designed for hazardous BOP (Blow-Out
Preventer) service in the Oil & Gas Industry. It meets or
exceeds the ISO 7241-1 Series B standard. Rated Pressure Chart
Body Maximum Working Minimum Burst

F eatures Part
Number Size Pressure (Connected) Pressure (Connected)
inches PSI BAR PSI BAR
STRAIGHT-THRU
• Easy visual verification: BOP designation is clearly marked on the 4HFR26 1/2 7,000 482 28,000 1,931
socket and plug, along with a distinctive red socket sleeve and red 6HFR26 3/4 5,000 344 18,150 1,251
plug wrench flats for simple identification 8HFR26 1 5,000 344 20,000 1,379
ML8HFR36* 1 5,000 344 20,000 1,379
• Dependable: equipped with ball-locking technology that provides
* Stainless Steel
a consistent, positive connection
• Compact design: ideal for building panels where space is limited
Lloyd’s Register Certification
• Easy to use: connect and disconnect quickly without tools and no All of the above items carry a Lloyd’s Registry Certificate for fire
risk of cross threading conditions stated in API 16D and EUB Directive 35. These parts met
• Safe: sleeve lock is standard which prevents accidental the requirements that state couplings shall be capable of maintaining
disconnects pressure when exposed to a 700° C (1,300° F) temperature for a
five-minute period. Testing for this certification was conducted at the
• Environmental protection: two-way valve design minimizes fluid following pressures in the connected condition:
spillage 4HFR26 / 4KFR26: 3,000 PSI / 206 BAR
6HFR31 / 6KFR31: 3,000 PSI / 206 BAR
GAS
8HFR36 / 8KFR36: 4,000 PSI / 275 BAR
A pplications & markets ML8HFR36 / ML8KFR36: 4,000 PSI / 275 BAR
• Oil & Gas
SOCKETS PLUGS
Thread Dimensions Female End Connections
Dimensions
ACCESSORIES
Body Detail Across

Part No. Size (Female) A B Flats Part No. Thread Size C D E HEX
4HFR26 1/2" 1/2-14 NPTF 2.96 1.86 1.13 4KFR26 1/2-14 NPTF 2.03 1.30 0.76 1.13
6HFR31 3/4" 3/4-14 NPTF 3.48 2.22 1.31 6KFR31 3/4-14 NPTF 2.36 1.52 0.71 1.31
8HFR36 1" 1-1½ NPTF 4.13 2.61 1.75 8KFR36 1-11½ NPTF 2.85 1.88 0.97 1.63
ML8HFR36* 1" 1-1½ NPTF 4.13 2.61 1.75 ML8KFR36* 1-11½ NPTF 2.85 1.88 0.97 1.63
*Stainless Steel
47
ISO 7241-1 Series A
HA15000 Series
Interchangeability
- ISO 7241-1 Series A
Materials
• Zinc-plated steel construction
retaining rings
1/4" to 1" nominal

(6.35 mm to 25.4 mm)
The HA15000 Series is a general purpose
hydraulic and fluid transfer coupling that conforms to the -4° F to 212° F
dimensional requirements of ISO 7241-1 Series A. -20° C to 100° C
Body sizes range from 1/4" to 1".
Rated Pressure
F eatures Body Size PSI BAR
1/4" 4,565 315
• Ball lock
3/8" 4,565 315
• Manual connect, disconnect 1/2" 3,625 250
3/4" 3,625 250
• Poppet valving 1" 2,900 200
• Slim profile
• Zinc plated steel construction Flow Capacity
• NPTF and BSPP end connections
• Available push-to-connect socket designed for bulkhead
mounting (1/2" body size only)

• Construction • Agriculture
• General Industry • Fluid Transfer
48
ISO 7241-1 Series A
HA15000 Series
ONE-WAY
Socket Plug
SOCKETS
Body Size Part Number Thread Size (female) Dimensions (inches)
(inch) (Steel) NPTF BSPP A B Across Flats
1/4 HA1521100 1/4-18 — 1.89 0.98 0.75
1/4 HA1501100 — 1/4-19 1.89 0.98 0.75
3/8 HA1522100 3/8-18 — 2.21 1.18 0.91
3/8 HA1502100 — 3/8-19 2.21 1.18 0.91
1/2 HA1523100 1/2-14 — 2.64 1.49 1.06
2.64 1.06
TWO-WAY
1/2 HA1503100 — 1/2-14 1.49
1/2 HA1523600* 1/2-14 — 2.64 1.49 1.06
1/2 HA1503600* — 1/2-14 2.64 1.49 1.06
3/4 HA1524100 3/4-14 — 3.25 1.88 1.38
3/4 HA1504100 — 3/4-14 3.25 1.88 1.38
1 HA1525100 1-11½ — 3.86 2.08 1.62
1 HA1505100 — 1-11 3.86 2.08 1.62
* Push-to-Connect Socket A = Overall Length B = Maximum Diameter
PLUGS
STRAIGHT-THRU
(inch) (Steel) NPTF BSPP C D E Hex
1/4 HA1521200 1/4-18 — 1.41 0.86 0.80 0.75
1/4 HA1501200 — 1/4-19 1.41 0.86 0.80 0.75
3/8 HA1522200 3/8-18 — 1.63 1.04 0.79 0.91
3/8 HA1502200 — 3/8-19 1.63 1.04 0.79 0.91
1/2 HA1523200 1/2-14 — 1.92 1.22 0.92 1.06
1/2 HA1503200 — 1/2-14 1.92 1.22 0.92 1.06
3/4 HA1524200 3/4-14 — 2.42 1.58 1.09 1.38
3/4 HA1504200 — 3/4-14 2.42 1.58 1.09 1.38
1 HA1525200 1-11½ — 2.81 1.85 1.19 1.62
1 HA1505200 — 1-11 2.81 1.85 1.19 1.62
GAS
Push-to-Connect Socket
Part Numbers This system allows automatic connection and disconnection

HA1503600 & simply by pushing the plug into or pulling it out of the socket Sleeve
dimensions
HA1523600 body. Pulling on the hose moves the socket body forward for bulkhead
relative to the bulkhead mounted double-acting sleeve, and
the plug is released without damage to the hose.
ACCESSORIES

Body Size (inch) Plug Dust Cap Part No. Socket Dust Plug Part No.
1/4 HP1511200 HP1511100
3/8 HP1512200 HP1512100 Vinyl Dust Cap
1/2 HP1513200 HP1513100
3/4 HP1514200 HP1514100
1 HP1515200 HP1515100
49
ISO 16028 Flat Face Hydraulic
FF Series
Interchangeability
- ISO 16028
Materials
• Zinc plated steel with clear chromate
and QPQ finish; RoHS Compliant
• Stainless steel springs and locking
balls
1/4" to 1" nominal

The FF Series is a flat face dry break or minimum spill (6.35 mm to 25.4 mm)
hydraulic coupling that meets or exceeds the ISO 16028
standard. FF series is ideal for applications where hydraulic -4° F to 212° F
spillage is a concern and interchangeability with other -20° C to 100° C
manufacturers is important. Body sizes are 1/4", 3/8", 1/2",
5/8", 3/4", and 1". Rated Pressure
5075 psi (350 BAR)
F eatures maximum operating pressure
• Heavy knurled sleeve creates a non-slip grip
• Meets or exceeds ISO 16028 standard Flow Capacity
(see below)
• 5075 psi maximum operating pressure for all sizes
(connected and disconnected)
• Push-to-connect
• Standard sleeve-locking device prevents accidental
disconnection
6FF 16FF
• Color identification rings available to help 40 60
Pressure drop - psi
35
Pressure drop - psi
prevent the crossing of lines 30

50
40
25
20 30
A pplications & markets 15

10
20
10
5
• Agriculture • Trucks 0 0
0 1 2 3 4 5 6 7 0 5 10 15 20 25 30 35 40
Flow rate - GPM Flow rate - GPM
• Construction • Skid Steer Loaders
10FF 19FF
• Hydraulic Tools • Injection Molding 60 60
50 50
Pressure drop - psi
• Overhead Bucket • Railway

Pressure drop - psi
40 40
Hoists • Transportation
30 30
20 20
• Oil & Gas • Mining 10 10
• General Industry • Public Utilities

0
0 2 4 6 8 10 12 14 16
0
0 10 20 30 40 50 60
• Chemical
12FF 25FF
60 60
50 50
Pressure - psi
Pressure - psi
40 40
30 30
20 20
10 10
0 0
0 5 10 15 20 25 30 0 10 20 30 40 50 60 70 80 90
50
FF Series
ONE-WAY
Socket
Dimensions (inches)
SOCKETS Socket Coupling
Body
Size Part Number Thread Size A B Hex Size Connected Length
6FFS25BS 1/4" BSPP 2.13 1.06 0.87
1/4" 6FFS25 1/4" NPT 2.13 1.06 0.87 3.7
6FFS56UN 9/16" UNF 2.13 1.06 0.87
10FFS37BS 3/8" BSPP 2.68 1.26 1.06
10FFS37 3/8" NPT 2.68 1.26 1.06
4.61
TWO-WAY
10FFS50BS 1/2" BSPP 2.8 1.26 1.06
10FFS50 1/2" NPT 2.8 1.26 1.06
10FFS16FMET M16 x 150 2.8 1.26 1.06
3/8"
10FFS56UN 9/16" UNF 2.8 1.26 1.06 4.84
10FFS75UN 3/4" UNF 2.8 1.26 1.06
10FFS87UN 7/8" UNF 2.91 1.26 1.18 5.08
10FFS56ORM* 9/16" UNF 3.11 1.26 0.94 5.47
10FFS75ORM* 3/4" UNF 3.19 1.26 0.94 5.63
12FFS50BS 1/2" BSPP 3.23 1.5 1.42
5.24
12FFS50 1/2" NPT 3.23 1.5 1.42
STRAIGHT-THRU
12FFS75BS 3/4" BSPP 3.35 1.5 1.42
1/2" 12FFS75 3/4" NPT 3.35 1.5 1.42
5.47
12FFS75UN 3/4" UNF 3.23 1.5 1.42
12FFS87UN 7/8" UNF 3.35 1.5 1.42
12FFS106UN 1-1/16" UN 3.46 1.5 1.42 5.71
16FFS50BS 1/2" BSPP 3.23 1.65 1.42
5.24
16FFS50 1/2" NPT 3.23 1.65 1.42
16FFS75BS 3/4" BSPP 3.35 1.65 1.42
5.47
5/8" 16FFS75 3/4" NPT 3.35 1.65 1.42
16FFS75UN 3/4" UNF 3.23 1.65 1.42 5.24
16FFS87UN 7/8" UNF 3.35 1.65 1.42 5.47
16FFS106UN 1-1/16" UN 3.46 1.65 1.42 5.71
19FFS75BS 3/4" BSPP 3.78 1.81 1.65
19FFS75 3/4" NPT 3.78 1.81 1.65
19FFS100BS 1" BSPP 3.78 1.81 1.65
3/4" 6.7
3.78 1.81 1.65
GAS
19FFS100 1" NPT
19FFS106UN 1-1/16" UN 3.78 1.81 1.65
19FFS131UN 1-5/16" UNF 3.78 1.81 1.65
25FFS100BS 1" BSPP 4.06 2.17 2.17
25FFS100 1" NPT 4.06 2.17 2.17
1" 25FFS125BS 1-1/4" BSPP 4.06 2.17 2.17 7.28
25FFS125 1-1/4" NPT 4.06 2.17 2.17
25FFS162UN 1-5/8" UN 4.06 2.17 2.17
* = external thread
ACCESSORIES
51
FF Series
Plug
Dimensions (inches)
PLUGS Plug Coupling
Body
Size Part Number Thread Size C D Hex Size Connected Length
6FFP25BS 1/4" BSPP 2.01 0.63 0.87
1/4” 6FFP25 1/4" NPT 2.01 0.63 0.87 3.7
6FFP56UN 9/16" UNF 2.01 0.63 0.87
10FFP37BS 3/8" BSPP 2.56 0.78 1.06
10FFP37 3/8" NPT 2.56 0.78 1.06
4.61
10FFP50BS 1/2" BSPP 2.68 0.78 1.06
10FFP50 1/2" NPT 2.68 0.78 1.06
10FFP16FMET M16 x 150 2.68 0.78 1.06
3/8”
10FFP56UN 9/16" UNF 2.68 0.78 1.06 4.84
10FFP75UN 3/4" UNF 2.68 0.78 1.06
10FFP87UN 7/8" UNF 2.8 0.78 1.18 5.08
10FFP56ORM* 9/16" UNF 2.99 0.78 0.94 5.47
10FFP75ORM* 3/4" UNF 3.07 0.78 0.94 5.63
12FFP50BS 1/2" BSPP 2.68 0.96 1.42
5.24
12FFP50 1/2" NPT 2.68 0.96 1.42
12FFP75BS 3/4" BSPP 2.8 0.96 1.42
1/2” 12FFP75 3/4" NPT 2.8 0.96 1.42
5.47
12FFP75UN 3/4" UNF 2.68 0.96 1.42
12FFP87UN 7/8" UNF 2.8 0.96 1.42
12FFP106UN 1-1/16" UN 2.91 0.96 1.42 5.71
16FFP50BS 1/2" BSPP 2.68 1.06 1.42
5.24
16FFP50 1/2" NPT 2.68 1.06 1.42
16FFP75BS 3/4" BSPP 2.8 1.06 1.42
5.47
5/8" 16FFP75 3/4" NPT 2.8 1.06 1.42
16FFP75UN 3/4" UNF 2.68 1.06 1.42 5.24
16FFP87UN 7/8" UNF 2.8 1.06 1.42 5.47
16FFP106UN 1-1/16" UN 2.91 1.06 1.42 5.71
19FFP75BS 3/4" BSPP 3.74 1.18 1.65
19FFP75 3/4" NPT 3.74 1.18 1.65
19FFP100BS 1" BSPP 3.74 1.18 1.65
3/4" 6.7
19FFP100 1" NPT 3.74 1.18 1.65
19FFP106UN 1-1/16" UN 3.74 1.18 1.65
19FFP131UN 1-5/16" UNF 3.74 1.18 1.65
25FFP100BS 1" BSPP 4.09 1.42 2.17
25FFP100 1" NPT 4.09 1.42 2.17
1" 25FFP125BS 1-1/4" BSPP 4.09 1.42 2.17 7.28
25FFP125 1-1/4" NPT 4.09 1.42 2.17
25FFP162UN 1-5/8" UN 4.09 1.42 2.17
* = external thread
Dust Cap Accessories:

Body Size (inch) Plug Dust Cap Part No. Socket Dust Cap Part No.
1/4 PDC6FF SDC6FF
3/8 PDC10FF SDC10FF
1/2 PDC12FF SDC12FF
5/8 PDC16FF SDC16FF
3/4 PDC19FF SDC19FF Vinyl Socket Dust Cap Vinyl Plug Dust Cap
1 PDC25FF SDC25FF
52
Wing Nut
5100 Series
Interchangeability
ONE-WAY
- Other manufacturers’ couplings
Materials
• Brass body (socket & plug)
• Zinc plated ductile iron wing nut
(socket)
• Stainless steel springs
TWO-WAY
3/4" to 1¼" nominal
(6.35 mm to 38.10 mm)
The 5100 Series coupling is a heavy-duty wing nut
coupling designed for use in hydraulic lines where dry break
and minimum air inclusion are required. It is ideal for hydraulic Rated Pressure
dump trucks, oil field equipment, spreading equipment and Body Series PSI
3/4" 3,000
applications requiring the ability to connect and/or disconnect 1" 3,000
under pressure. Body sizes range from 3/4" up to 11/4". 11/4" 2,750
STRAIGHT-THRU
F eatures Flow Capacity
¾" 1" 1¼"
• Flat face valve design 43.5
• Non-spill double shut-off with minimum air inclusion 29
• Connect/disconnect under pressure 14.5
• Corrosion resistant brass body 7.25
• Plugs can be bulkhead mounted 4.35
• Interchanges with other manufacturers’ couplings 2.9
• Available with wing or hex nut configuration 1.45
A pplications & M A R K E T S 0.725

1.06 2.64 5.28 13.2 26.4 52.8 79 100
• Trucks • Construction
• Oil and Gas • Transportation
GAS
Dust Caps and Dust
Bulkhead Mounting Flanges Plugs Accessories
Diameters (inches) Plug Dust Socket
Body Bolt Bolt Cap Dust Plug
Series Part No. Hole A Circle B (Brass) (Brass)
3/4" 150-22-12 .201 2.12 5100-S7-12 5100-S9-12
1" 150-22-16 .201 2.38 5100-S7-16 5100-S9-16
1¼" 150-22-20 .201 2.62 5100-S7-20 5100-S9-20
ACCESSORIES
SOCKETS PLUGS
Dimensions Dimensions
Body Thread Size Across Body Thread Size Across
Size Part No. NPT A B Flats Size Part No. NPT C D Flats
3/4" 5100-S5-12B 3/4-14 3.07 4.13 1.16 3/4" 5100-S2-12B 3/4-14 3.11 1.38 1.19
1" 5100-S5-16B 1-11½ 3.68 4.38 1.44 1" 5100-S2-16B 1-11½ 3.55 1.74 1.56
1¼" 5100-S5-20B 1¼-11½ 4.00 5.27 1.78 1¼" 5100-S2-20B 1¼-11½ 3.71 2.08 1.88
53
Ultra Pressure 10,000 PSI
UP 10 Series
Interchangeability
- Proprietary
Materials
• High strength steel body and
valve
• Stainless steel springs & balls
• PTFE back-up ring (socket)
1/4" nominal
The UP10 Series is a high pressure hydraulic quick (6.35 mm)
connect coupling designed to operate at pressures up to
10,000 psi. Unlike most high pressure hydraulic couplings -40° F to 250° F
that are screw-to-connect, the UP10 Series has a ball -40° C to 121° C
locking mechanism, making it quicker & easier to connect.
Body size is 1/4". Rated Pressure
10,000 psi (700 BAR)
F eatures
Flow Capacity
• Ball lock
• Slim profile
• High strength steel construction
• Poppet valves with metal-to-metal sealing
• 1/4" & 3/8" male & female NPTF end connections
• Standard sleeve lock

• Construction
• Hydraulic Tools
54
Ultra Pressure 10,000 PSI
UP 10 Series
SOCKETS PLUGS
Dimensions Male End Connections Dimensions
ONE-WAY
Part No. Thread Size A B HEX Part No. Thread Size C D HEX
UP10S25M 1/4-18 NPTF 2.69 1.18 0.88 UP10P25M 1/4-18 NPTF 2.59 0.97 0.88
UP10S37M 3/8-18 NPTF 2.69 1.18 0.88 UP10P37M 3/8-18 NPTF 2.59 0.97 0.88
Dimensions Female End Connections Dimensions

UP10S25F 1/4-18 NPTF 2.64 1.18 0.88 UP10P25F 1/4-18 NPTF 2.54 0.97 0.88
UP10S37F 3/8-18 NPTF 2.69 1.18 0.88 UP10P37F 3/8-18 NPTF 2.59 0.97 0.88
TWO-WAY
Coupling Series Plug Dust Cap Part No. Socket Dust Plug Part No. Vinyl Dust Plug
UP10 PPDC2HK PSDC2HK
STRAIGHT-THRU
Vinyl Dust Cap
GAS
ACCESSORIES
55
Thread-to-Connect 10,000 PSI
WA56000/HP3 Series
Interchangeability
- Other manufacturers’ couplings
Materials
• Zinc plated steel construction
• High strength steel ball valve
• Stainless steel spring
• WA: Buna-N (Nitrile) seal
HP3: Urethane seal
• PTFE back-up ring (WA socket)
The WA56000 and HP3 Series are high 1/4" and 3/8" nominal
pressure hydraulic screw together couplings designed to (6.35 mm and 9.525 mm)
operate at pressures up to 10,000 psi. Their rugged design
makes them suitable for use in hydraulic ram, pump and high -40° F to 250° F
impulse applications. The WA 56000 has a poppet valve and -40° C to 121° C
HP3 has a ball valve. Body sizes are 1/4" and 3/8".
Rated Pressure
Body Size PSI BAR
F eatures 1/4" 10,000 690
• Threaded latching 3/8" 10,000 690
• Rugged steel construction Flow Capacity

• Poppet valves with elastomer seal standard in 1/4" coupling
• Poppet valves and ball valves available in 3/8" coupling
• Body size matches thread size. 1/4" and 3/8" body sizes do not
interchange.

• General Industry • Oil & Gas • Test Equipment
• Hydraulic Tools • Construction

Body Size Plug Dust Cap Socket Dust Plug
Part No. Part No.
1/4" WA5611400 WA5611700
3/8" W 5612400 WA5612700
Sockets – Male End Connections Plugs – Female End Connections

Thread Thread Dimensions
Valve Size Dimensions Valve Size Across
Part No. Type NPTF A B HEX Part No. Type NPTF C D Flats
WA5651700 Poppet 1/4-18 2.36 1.12 0.88 WA5651400 Poppet 1/4-18 1.26 1.10 0.75
WA5652700 Poppet 3/8-18 2.76 1.38 1.06 WA5652400 Poppet 3/8-18 1.52 1.26 0.91
HP3SB37M Ball 3/8-18 2.76 1.38 1.06 HP3PB37F Ball 3/8-18 1.52 1.26 0.91
56
1/4" Nominal
2HKIG & 2HKIL Series
ONE-WAY
Interchangeability
- Proprietary
Materials
• Stainless steel body, valve,
sleeve, springs, balls and
retaining ring
• Buna-N (Nitrile) seals; optional
PTFE, Fluorocarbon, and EPDM
• Socket identification ring
TWO-WAY
2HKIG: White acetal
2HKIL: Black acetal
The 2HKIG and 2HKIL Series stainless steel
couplings can be used with various liquids and gases. They 1/4" nominal
are functionally identical, but do not interchange. They can (6.35 mm)
be used where it is necessary to avoid crossing lines.
-40° F to 250° F
F eatures -40° C to 121° C
STRAIGHT-THRU
• Ball lock
• Manual operation Rated Pressure
• Do not interchange with one another 1500 psi (103 BAR)
• 1/4" body size
• All-stainless steel construction Flow Capacity
• Sockets available with right-angle connection
• Chemical • General Industry • Military
• Food and Beverage • Aerospace
2HKIG
2HKIL GAS
ACCESSORIES
57
1/4" Nominal
2HKIG & 2HKIL Series
SOCKETS 2HKIG PLUGS

2HIG10 1/8-27 NPTF 2.18 1.06 0.81 2KIGF15 1/4-18 NPTF 1.98 1.01 0.69
2HIG20 3/8-18 NPTF 2.31 1.06 0.81
2HIG720* 7/16-20 2.27 1.06 0.81
2HIGLLRA720†* 7/16-20 2.09 1.06 —

2HIG16 1/4-18 NPTF 2.26 1.06 0.81 2KIGF720* 7/16-20 1.61 1.01 0.69
2KIGF 9/16-18 1.17 1.01 0.88
SOCKETS 2HKIL PLUGS

2HIL10 1/8-27 NPTF 2.18 1.06 0.81 2KILF15 1/4-18 NPTF 1.98 1.01 0.69
2HIL20 3/8-18 NPTF 2.31 1.06 0.81
2HIL720* 7/16-20 2.27 1.06 0.81
2HILLLRA720†* 7/16-20 2.09 1.06 —

2HIL16 1/4-18 NPTF 2.26 1.06 0.81 2KILF720* 7/16-20 1.61 1.01 0.69
2KILF 5/8-18 1.17 1.01 0.88
* 1/4" SAE Flare † Right-Angle End Connection
Dust Caps Accessories:
Coupling Series Plug Dust Cap Socket Dust Plug

Vinyl Plug Dust Cap
Part No. Part No.
2HKIG PPDC2HK PPDC4HK
2HKIL PPDC2HK PPDC4HK Vinyl Dust Plug
Optional Seal Materials: 115-PTFE, 143-Fluorocarbon, 192-EPDM
58
316 Stainless Steel Flat Face
DB Series
ONE-WAY
Interchangeability
- ISO 16028 (3/8" only)
- Proprietary (All other sizes)
Materials
• 316L stainless steel construction
• Fluorocarbon seals; EPDM, Kalrez
or other seal materials optional
1/4" to 1" nominal

(6.35 mm to 19.6 mm)
TWO-WAY
The DB Series is designed for fluid handling where
minimum spillage and minimum air inclusion are required.
-4° F to 392° F
-20° C to 200° C ]
Fluorocarbon
Couplings in this series are constructed of 316L stainless

steel, which makes them suitable for use in cooling systems,
40° F to 302° F
40° C to 150° C
EPDM ]
chemical, pharmaceutical and food processing industries.
Rated Pressure
Unique interchange prevents the crossing of lines (except
Body Socket Plug Connected
3/8" size). Body sizes range from 1/4" to 1".
STRAIGHT-THRU
Size PSI BAR PSI BAR PSI BAR
1/4" 2,030 140 2,755 190 2,755 190
F eatures 3/8" 2,030 140 2,610 180 2,610 180
1/2" - 1" 1,450 100 2,030 140 2,030 140
• Ball lock Spillage & Air Inclusion
Flow Capacity
• Push-to-connect Spillage
Air
Body Inclusion
• Minimal fluid loss when Size
Max. per
Disconnect
Max. per
disconnecting Connect
1/4" 0.010 ml 0.005 ml
• Minimal air inclusion when
3/8" 0.016 ml 0.010 ml
connecting
1/2" 0.020 ml 0.020 ml
• High flow capacity 3/4" 0.030 ml 0.100 ml
• NPTF and BSPP threads available 1" 0.035 ml 0.126 ml
GAS
• Fluid Transfer • Food and Beverage • Pharmaceutical
• Chemical • Oil and Gas • Medical Equipment
• Transportation • Military • Aerospace
• Nuclear • Cooling Systems
SOCKETS PLUGS
ACCESSORIES
Body Thread Body Thread

Size Size Dimensions Size Size Dimensions
(inch) Part No. (Female) A B HEX (inch) Part No. (Female) C D HEX
1/4 2DBS25F 1/4-18 NPTF 1.98 1.02 0.88 1/4 2DBP25F 1/4-18 NPTF 1.65 1.00 0.87
1/4 2DBS25FBS 1/4-19 BSPP 1.98 1.02 0.88 1/4 2DBP25FBS 1/4-19 BSPP 1.65 1.00 0.87
1 8DBS100F 1-11½ NPTF 3.52 2.25 1.81 1 8DBP100F 1-11½ NPTF 3.52 2.08 1.81
1 8DBS100FBS 1-11 BSPP 3.52 2.25 1.81 1 8DBP100FBS 1-11 BSPP 3.52 2.08 1.81
59
Straight
Through
60
Straight Through
Locking
Body Size Body Material Options
Mechanism
ONE-WAY
PLASTIC (Polypropylene)
STEEL (Plugs Only)
PLASTIC FINGERS
DUST CAP/PLUG
SLEEVE LOCK
BALL LOCK
1/8 INCH
1/4 INCH
3/8 INCH
1/2 INCH
3/4 INCH
1¼ INCH
1½ INCH
2½ INCH
BRASS
1 INCH
2 INCH
TWO-WAY
Coupling
Series Page
1ST 63/64 ● ● ● ● ● ● ●
2ST 63/64 ● ● ● ● ● ● ● ▼
3ST 63/64 ● ● ● ● ● ● ● ▼
4ST 63/64 ● ● ● ● ● ● ●
STRAIGHT-THRU
6ST 63/64 ● ● ● ● ● ● ● ♦
8ST 63/64 ● ● ● ● ● ● ● H
10ST 63/64 ● ● ● ● ● ● ● H
12ST 63/64 ● ● ● ● ● ● ●
16ST 63/64 ● ● ● ● ● ● ●
20ST 63/64 ● ● ● ● ● ●
P2ST 65 ● ● ●
P3ST 65 ● ● ●
67 ● ● ● ● ● ●
GAS
Flo-Temp
▼Socket Dust Plug Only ♦ Socket Dust Plug and Dust Cap H Plug Dust Cap Only
ACCESSORIES
61
Straight Through
ST Series
Interchangeability
- Other manufacturers’ ST style
couplings
Materials
• Brass or 303 stainless steel socket
• Stainless steel spring, balls and
retaining ring
• Brass, zinc plated steel and 303
stainless steel plug
• High impulse heat treated 416
ST Series straight through couplings are designed for stainless steel plugs available in
use where minimum pressure drop is required and valving 1/4" and 3/8" body sizes
is not needed. They are well suited for use on pressure • Buna-N (Nitrile) seal;
wash, steam and carpet cleaning equipment, and many fluid PTFE (1-ST through 8-ST),
Neoprene, Fluorocarbon (FKM) and
transfer systems. Body sizes range from 1/8" to 2½".
EPDM available
F eatures 1/8" to 2½" nominal

• Ball lock (3.175 mm to 63.5 mm)
-40° F to 250° F
• Smooth bore permits free flow of liquid or gas -40° C to 121° C
• Male and female NPTF, BSPP and hose stem connections
Rated Pressure*
A pplications & markets Brass Socket Brass Socket Stainless Steel
Body Brass Plug Steel Plug Socket & Plug
• General Industry • Marine • Medical Series Size PSI BAR PSI BAR PSI BAR
• Military 1/8" 2,800
• Fluid Transfer • Breathing Equipment 1ST 193 3,400 234 4,200 290
2ST 1/4" 5,200 359 5,500 379 7,500 517
• Chemical • Carpet Cleaning • Pressure Wash 3ST 3/8" 2,800 193 4,200 290 6,300 434
4ST 1/2" 2,200 152 3,500 241 3,600 248
• Food and Beverage • Steam Cleaning • Cooling Systems 6ST 3/4" 1,700 117 2,100 145 3,000 207
8ST 1" 1,300 90 2,000 138 2,000 138
• Injection Molding 10ST 1,700 117 2,700 186 2,200 152
1¼"
12ST 1½" 1,400 97 2,200 152 2,500 172
16ST 2" 1,400 97 2,200 152 1,500 103
Flow Capacity 20ST 2½" 900 62 1,500 103 – –
* Pressure ratings are for sockets and plugs with threaded end connections. Pressure
ratings of couplings with hose stems may be significantly lower, and will depend
on the type of hose and the method of clamping. Refer to hose manufacturer’s end
connection pressure ratings. The best way to determine suitability for an application is
to run pressure testing under controlled conditions.
SOCKET BODY SLEEVE PLUG
LOCKING
O-RING SLEEVE BALLS
SPRING
62
Straight Through
ST Series
SOCKETS Body
Size
Part Number Thread Size Dimensions
Brass Stainless NPTF BSPP A B Hex
1/8 1S10 LL1S10 1/8-27 — 1.06 0.72 0.56
1/8 1S10BS LL1S10BS — 1/8-28 1.08 0.72 0.56
Male End 1/4 2S15 LL2S15 1/4-18 — 1.72 0.97 0.81
ONE-WAY
Connections 1/4 2S15BS LL2S15BS — 1/4-19 1.56 0.97 0.81
3/8 3S20 LL3S20 3/8-18 — 1.75 1.16 1.00
3/8 3S20BS LL3S20BS — 3/8-19 1.71 1.16 1.00
1/2 4S25 LL4S25 1/2-14 — 2.03 1.34 1.13
1/2 4S25BS LL4S25BS — 1/2-14 1.85 1.34 1.13
3/4 6S30 LL6S30 3/4-14 — 2.22 1.72 1.44
3/4 6S30BS — — 3/4-14 2.11 1.72 1.44
1 8S35 — 1-111/2 — 2.53 2.03 1.75
1 8S35BS — — 1-11 2.43 2.03 1.75
TWO-WAY
Body Part Number Thread Size Dimensions
Size Brass Stainless NPTF BSPP A B Hex
1/8 1S11 LL1S11 1/8-27 — 1.06 0.72 0.56
Female End 1/8 1S11BS LL1S11BS — 1/8-28 1.03 0.72 0.56
Connections 1/4 2S16 LL2S16 1/4-18 — 1.50 0.97 0.81
1/4 2S16BS LL2S16BS — 1/4-19 1.50 0.97 0.81
3/8 3S21 LL3S21 3/8-18 — 1.59 1.16 1.00
3/8 3S21BS LL3S21BS — 3/8-19 1.59 1.16 1.00
1/2 4S26 LL4S26 1/2-14 — 1.91 1.34 1.13
STRAIGHT-THRU
1/2 4S26BS LL4S26BS — 1/2-14 1.91 1.34 1.13
3/4 6S31 LL6S31 3/4-14 — 2.06 1.72 1.44
3/4 6S31BS LL6S31BS — 3/4-14 2.06 1.72 1.44
1 8S36 LL8S36 1-11½ — 2.33 2.03 1.75
1 8S36BS LL8S36BS — 1-11 2.33 2.03 1.75
1¼ 10S41* LL10S41 1¼-11½ — 2.44 2.50 2.00
1¼ 10S41BS* — — 1¼-11 2.51 2.50 2.00
1½ 12S46* LL12S46 1½-11½ — 2.88 3.13 2.63
1½ 12S46BS* LL12S46BS — 1½-11 2.88 3.13 2.63
2 16S51* LL16S51 2-11½ — 3.09 3.75 3.00
2 16S51BS* LL16S51BS — 2-11 3.30 3.75 3.00
2½ 20S56* — 2½-8 — 3.44 4.50 3.50

* With Steel Sleeve
GAS
Hose Stem Body Part Number Dimensions
Hose I.D.
Connections Size Brass Stainless A B
1/8 1S12 LL1S12 3/16" 1.41 0.72
1/8 1S17 LL1S17 1/4" 1.41 0.72
1/4 2S17 LL2S17 1/4" 2.10 0.97
3/8 3S22 LL3S22 3/8" 2.09 1.16
1/2 4S27 LL4S27 1/2" 2.19 1.34
ACCESSORIES
3/4 6S32 LL6S32 3/4" 3.19 1.72

1 8S37 LL8S37 1" 3.32 2.03
63
Straight Through
ST Series

PLUGS (inch) Brass Steel Stainless NPTF BSPP C D Hex
1/8 B1T10 1T10 LL1T10 1/8-27 — 1.06 0.51 0.44
1/8 B1T10BS — — — 1/8-28 0.97 0.65 0.56
1/8 B1T15 1T15 — 1/4-18 — 1.22 0.65 0.56
Male End 1/4 B2T15 2T15 LL2T15 1/4-18 — 1.56 0.65 0.56
Connections 1/4 — — HL2T15* 1/4-18 — 1.56 0.65 0.56
1/4 B2T15BS — LL2T15BS — 1/4-19 1.46 0.87 0.75
3/8 B3T20 3T20 LL3T20 3/8-18 — 1.69 0.79 0.69
3/8 — — HL3T20* 3/8-18 — 1.69 0.79 0.69
3/8 B3T20BS — LL3T20BS — 3/8-19 1.59 1.01 0.88
1/2 B4T25 4T25 LL4T25 1/2-14 — 2.01 1.01 0.88
1/2 B4T25BS — LL4T25BS — 1/2-14 1.82 1.15 1.00
3/4 B6T30 6T30 LL6T30 3/4-14 — 2.20 1.23 1.06
3/4 B6T30BS — LL6T30BS — 3/4-14 2.08 1.44 1.25
1 B8T35 8T35 LL8T35 1-11½ — 2.49 1.59 1.38
1 B8T35BS — — — 1-11 2.36 2.02 1.75
1¼ B10T40 10T40 LL10T40 1¼-11½ — 2.72 2.02 1.75
1¼ B10T40BS — — — 1¼-11 2.55 2.31 2.00
1½ B12T45 12T45 — 1½-11½ — 3.31 2.60 2.25
1½ B12T45BS — — — 1½-11 3.19 2.60 2.25
2 B16T50 16T50 LL16T50 2-11½ — 3.50 3.18 2.75
2 — — LL16T50BS — 2-11 3.54 3.18 2.75
2½ B20T55 — — 2½-8 — 4.24 3.75 3.25

(inch) Brass Steel Stainless NPTF BSPP C D Hex
Female End 1/8 B1T11 1T11 LL1T11 1/8-27 — 0.97 0.58 0.50
Connections 1/8 B1T11BS — LL1T11BS — 1/8-28 0.97 0.65 0.56
1/4 B2T16 2T16 LL2T16 1/4-18 — 1.45 0.79 0.69
1/4 — — HL2T16* 1/4-18 — 1.45 0.79 0.69
1/4 B2T16BS — LL2T16BS — 1/4-19 1.45 0.87 0.75
3/8 B3T21 3T21 LL3T21 3/8-18 — 1.63 0.94 0.81
3/8 — — HL3T21* 3/8-18 — 1.63 0.94 0.81
3/8 B3T21BS — LL3T21BS — 3/8-19 1.63 1.01 0.88
1/2 B4T26 4T26 LL4T26 1/2-14 — 1.92 1.15 1.00
1/2 B4T26BS — LL4T26BS — 1/2-14 1.92 1.23 1.06
3/4 B6T31 6T31 LL6T31 3/4-14 — 2.01 1.37 1.19
3/4 B6T31BS — LL6T31BS — 3/4-14 2.01 1.52 1.31
1 B8T36 8T36 LL8T36 1-11½ — 2.21 1.80 1.56
1 B8T36BS — LL8T36BS — 1-11 2.23 1.80 1.56
1¼ B10T41 10T41 LL10T41 1¼-11½ — 2.34 2.31 2.00
1¼ B10T41BS — — — 1¼-11 2.53 2.31 2.00
1½ B12T46 12T46 LL12T46 1½-11½ — 2.88 2.60 2.25
1½ B12T46BS — — — 1½-11 2.88 2.60 2.25
2 B16T51 16T51 — 2-11½ — 3.03 3.18 2.75
2 B16T51BS — — — 2-11 3.25 3.18 2.75
2½ B20T56 20T56 — 2½-8 — 3.37 3.75 3.25
* High impulse heat treated 416 stainless steel
Hose Stem Body Size Part Number Dimensions (inches)

Hose I. D.
Connections (inch) Brass Stainless C DØ
1/8 B1T12 LL1T12 3/16" 1.28 0.44
1/8 B1T17 LL1T17 1/4" 1.28 0.44
1/4 B2T17 LL2T17 1/4" 1.93 0.56
3/8 B3T22 LL3T22 3/8" 2.09 0.69
1/2 B4T27 LL4T27 1/2" 2.17 0.88
3/4 B6T32 LL6T32 3/4" 3.17 1.19
1 B8T37 LL8T37 1" 3.28 1.50
Dust Caps and Dust Plugs Accessories: Series Plug Dust Cap (Vinyl) Socket Dust Plug (Vinyl)
2ST – PSDC1HK
3ST – PSDC2HK
Vinyl Dust Plug 6ST PPDC4HK PSDC4HK
8ST PPDC6HK –
Vinyl Dust Cap 10ST PPDC8HK –
64
Straight Through
P2ST & P3ST Series
ONE-WAY
Interchangeability
- 2ST and 3ST
Materials
• Polypropylene construction
• Buna-N (Nitrile) seal

(6.35 mm to 9.525 mm)
TWO-WAY
-4° F to176° F
P2ST and P3ST Series couplings have the same -20° C to 80° C
design as the ST, but with polypropylene construction,
specifically designed for use with medical equipment. They
Rated Pressure
can also be used in a variety of low pressure fluid transfer
Temperature* PSI BAR
applications.
75° 110 8
200° 30 2
F eatures
STRAIGHT-THRU
*235° F maximum sterilization temperature
• Interchange with 2ST and 3ST

• Excellent chemical resistance
• Light weight
• Medical • Chemical
• Fluid Transfer • Pharmaceutical
SOCKETS PLUGS
GAS
Hose Dimensions Dimensions
Series Part No. I.D. A B Series Part No. Thread Size C D HEX
P2ST P2STS25H 1/4" 2.07 1.12 P2ST P2STP25M 1/4-18 NPTF 1.56 0.65 0.56
Each P2-ST socket uses one Part No. 902-7 o-ring. P3ST P3STP25M 1/4-18 NPTF 1.69 0.79 0.69
P3ST P3STS37H 3/8" 2.61 1.37 P3ST P3STP37M 3/8-18 NPTF 1.69 0.79 0.69
Each P3-ST socket uses one Part No. 902-10-199 o-ring.
Dimensions
Series Part No. Hose I.D. C D
ACCESSORIES
P3ST P3STP37H 3/8" 2.16 0.79
65
Straight Through
Flo-Temp 200/300/500 Series
Interchangeability
– Other manufacturers’ coolant
line couplings
Materials
• Brass socket construction
• Stainless steel spring and
locking balls
• Fluorocarbon seal
(-30° F to +450° F)
• Brass plug
Flo-Temp couplings provide the flow needed to cool
or heat injection molds and die casting dies. Sockets are 1/4" to 1/2" nominal
(6.35 mm to 12.7 mm)
available non-valved for maximum flow and valved to
prevent fluid loss when disconnected. Flo-Temp couplings
can be used with water-glycol, hot water and hot oil. Body -30° F to 450° F
sizes are 1/4", 3/8" and 1/2". -34° C to 232° C
F eatures Rated Pressure

200 psi / 14 BAR
• Non-valved straight through models for maximum flow
• Valved sockets for automatic shut-off when line is disconnected
• Sockets available with straight, 90° or 45° hose stems or Flow Capacity
without hose stem
• Brass plugs with male pipe thread for recessed mounting to
avoid damage to plugs when molds are being changed or
stored
PRESSURE DROP, psid
• Injection Molding • Heating/Cooling
R E P L A C E M E N T PA R T S
Part Number
Description
Series 200 Series 300 Series 500
Seal WFT200228 WFT300228 WFT500228
Valve VFT200 VFT300 VFT500 FLOW RATE, gpm
Valve O-Ring 9023143 9038143 9143143 (Water)
Valve Spring VSFT200 VS3000 VSFT500
66
Straight Through
Flo-Temp 200/300/500 Series
SOCKETS
ONE-WAY
Without Hose Stem 90° Hose Stem
Body Dimensions (inches) Thread Body Dimensions
Size Size Size Part Number Hose (inches)
(inch) Part Number A B HEX NPTF (inch) Non-Valved Valved I.D, A B C
1/4 LNFT200 1.68 0.67 0.56 1/8-27 1/4 FTS214 FTS214V 1/4” 1.36 0.67 2.17
3/8 LNFT300 2.18 0.89 0.75 1/4-18 1/4 FTS214HP* FTS214VHP* 1/4” 1.18 0.67 1.76
1/2 LNFT500 2.00 1.17 1.13 1/2-14 1/4 FTS215 FTS215V 5/16” 1.18 0.67 1.76
1/4 FTS216 FTS216V 3/8” 1.17 0.67 1.76
1/4 FTS216HP* FTS216VHP* 3/8” 1.17 0.67 1.76
3/8 FTS316 FTS316V 3/8” 1.60 0.88 2.43
3/8 FTS316HP* FTS316VHP* 3/8” 1.60 0.88 2.43
TWO-WAY
3/8 FTS318 FTS318V 1/2” 1.60 0.88 2.43
3/8 FTS318HP* FTS318VHP* 1/2” 1.60 0.88 2.43
Straight Hose Stem

Body Dimensions
Size Part Number Hose (inches)
(inch) Non-Valved Valved I.D, A B C
1/4 FTS204 FTS204V 1/4” 1.20 0.67 2.25
45° Hose Stem
STRAIGHT-THRU
1/4 FTS204HP* FTS204VHP* 1/4” 1.20 0.67 2.09 Body Dimensions
1/4 FTS205 FTS205V 5/16” 1.20 0.67 2.09 Size Part Number Hose (inches)
1/4 FTS206 FTS206V 3/8” 1.20 0.67 2.25 (inch) Non-Valved Valved I.D, A B C
1/4 FTS206HP* FTS206VHP* 3/8” 1.20 0.67 2.34 1/4 FTS224 FTS224V 1/4” 1.17 0.67 2.40
3/8 FTS306 FTS306V 3/8” 1.60 0.91 2.68 1/4 FTS224HP* FTS224VHP* 1/4” 1.17 0.67 2.40
3/8 FTS306HP* FTS306VHP* 3/8” 1.61 0.89 2.75 1/4 FTS225 FTS225V 5/16” 1.17 0.67 2.40
3/8 FTS308 FTS308V 1/2” 1.61 0.88 2.82 1/4 FTS226 FTS226V 3/8” 1.17 0.67 2.40
3/8 FTS308HP* FTS308VHP* 1/2” 1.61 0.88 2.82 1/4 FTS226HP* FTS226VHP* 3/8” 1.17 0.67 2.40
1/2 FTS504 FTS504V 1/2” 2.25 1.18 3.42 3/8 FTS326 FTS326V 3/8” 1.80 0.90 3.70
1/2 FTS506 FTS506V 3/4” 2.22 1.18 3.85 3/8 FTS328 FTS328V 1/2” 1.60 0.90 3.17
*Part numbers with HP suffix have push-on hose barb. All other FTS part numbers have standard hose barb.
PLUGS
GAS
Male Pipe Thread Female Pipe Thread
Body Dimensions Installation Body Dimensions (inches)
Size Part Number (inches) Recess Size Part Number
(inch) Brass Thread Size D E HEX Dia. Depth (inch) Brass Thread Size D E HEX
1/4 FTP251 1/8-27 NPTF 0.94 0.49 0.44 0.69 0.69 1/4 FTP251F 1/8-27 NPTF 1.00 0.58 0.50
1/4 FTP251BST 1/8-28 BSPT 0.94 0.49 0.44 0.69 0.69 1/4 FTP251FBS 1/8-28 BSPT 1.00 0.65 0.56
1/4-18 NPTF 1.15 0.63 0.56 0.84 0.94 1/4 FTP252F 1/4-18 NPTF 1.20 0.72 0.63
ACCESSORIES
1/4 FTP252
67
Gas
68 68
Gas Safety
Gas-Mate Series
ONE-WAY
Interchangeability
– 3/8" ANSI Z 21.41;
Other sizes proprietary
Materials
• Brass construction
• Stainless steel locking balls
• Fluorocarbon (FKM) socket o-ring
• Valve actuator sodered to plug
with low melting temperature alloy
TWO-WAY
Gas-Mate couplings are one-way shut-off safety 3/8" to 1¼" nominal
couplings designed for the connection of gas cooking (9.525 mm to 31.75 mm)
appliances and other gas-fired devices. Body sizes are
3/8", 1/2", 3/4", 1" and 1¼". -40° F to 250° F
-40° C to 121° C
F eatures
Capacities
STRAIGHT-THRU
• Connect and disconnect without using wrenches Body Socket Plug Capacity* Socket O-Ring
Size Part No. Part No. BTU/hr Part No.
• Automatic shut-off when plug is removed from socket 3/8" 100006 100506 60,000 9143143M
• In case of fire, heat-sensitive plug allows socket valve to 1/2" 100008 100508 90,000 90214143M
close, stopping gas flow 3/4" 100010 100510 245,000 90218143M
• Push-to-connect (1¼" only) 1" 100012 100512 310,000 90223143M

1¼" GMS1250FH GMP1250F 500,000 91426143M
A pplications & I ndustries * Capacity is based on natural gas having a specific gravity of 0.64 and
a heat capacity of 1,000 BTU per cubic foot. Inlet pressure is 12 inches
water column and the pressure drop is 0.3 inch water column.
• Industrial • Fuel Gas Systems • Food & Beverage
SOCKETS PLUGS
Dimensions
Body Thread Across Body Thread Dimensions
Size Part No. Size NPTF A B Flats Size Part No. Size NPTF C D HEX
GAS
3/8" 100006 3/8-18 2.44 1.13 1.00 3/8" 100506 3/8-18 1.59 0.94 0.81
1/2" 100008 1/2-14 2.84 1.38 1.13 1/2" 100508 1/2-14 1.94 1.16 1.00
3/4" 100010 3/4-14 3.17 1.75 1.50 3/4" 100510 3/4-14 2.06 1.52 1.31
1" 100012 1-11½ 3.94 2.13 1.75 1" 100512 1-11½ 2.47 1.73 1.50
Body Thread Dimensions Body Thread Dimensions

Size Part No. Size NPTF A B HEX Size Part No. Size NPTF C D HEX
1¼" GMS1250FH 1¼-11½ 4.15 2.28 2.00 1¼" GMP1250F 1¼-11½ 2.44 2.16 1.88
ACCESSORIES
Dust Caps and Dust Plugs Accessories: CANADIAN

Plug Dust Cap Part No. Socket Dust Plug Part No. STANDARDS
Body Size
Metal Vinyl Metal Vinyl ASSOCIATION*
3/8" PDC2HK* PPDC2HK SDC2HK* PSDC2HK Complies with the requirements of
1/2" PDC3HK* PPDC3HK SDC3HK* PSDC3HK ANSI Z21.41 & CSA 6.9.
3/4" PDC4HK** PPDC4HK SDC4HK** PSDC4HK * CSA design certified, in both the United States and Canada, for
1" PDC6HK** PPDC6HK SDC6HK** PSDC6HK natural gas, manufactured gas, liquified petroleum and LP gas-air
*Brass **Aluminum mixtures at pressures not in excess of 1/2 psig (3.5 kPa).
69
Accessories
70
Accessories
FS Flow Sensor Series
ONE-WAY
Materials
• Brass body
• Acetal valve (1/4” - 1”)
• Brass valve (1½”)
• Stainless steel valve spring
Rated Pressure
80
MINIMUM INLET PRESSURE, psig

70
TWO-WAY
B4FS25F2 B12FS75F13
B6FS37F5 B16FS100F21
FS Flow Sensors Series are designed to B8FS50F8 B24FS150F45
protect personnel and property in case of hose failure in
compliance with Federal Safety Regulations. Flow Sensors
are intended for use with compressed air.
F eatures
STRAIGHT-THRU
• Automatically shuts off air • 250 psig pressure rating (all
flow to ruptured hose sizes) HOSE LENGTH, feet
• Reduces risk of injury or • Low pressure drop Flow Data - The graph above indicates the minimum inlet pressure
damage from hose whip for various hose lengths. Each Flow Sensor has a shut-off flow rat-
• Operates in any orientation
ing dependent upon inlet pressure. The length of hose and fitting size
• Automatically resets after • Compact design, economical, are critical in the proper operation of the valve. For example, with the
failure correction tamper-resistant B8-FS-50F-8 Flow Sensor, the hose I.D. must be 1/2" using only 1/2"
pipe thread end fittings. Thirty feet of hose requires at least 20 psig
inlet pressure; fifty feet of hose requires at least 28 psig inlet pressure;
A pplications & I ndustries and seventy-five feet of hose requires at least 36 psig inlet pressure.
• General Industry • Pneumatic Tools Inlet pressures lower than those indicated on the curves above will not
guarantee protection in case of hose failure. Valve shut-off occurs only
when flow exceeds the flow rating for the inlet pressure.
If hose lengths greater than 75 feet are required, a 1/2" size or larger
Flow Sensor must be installed on the inlet end of each 75-foot sec-
GAS
tion, and a correspondingly higher inlet pressure must be supplied for
proper operation of the Flow Sensor to assure safety.
Thread Shut-Off Flow, scfm, at Inlet Pressure, Psig Dimensions

Body
Part Number Size
Size 60 80 100 100 140 160 180 200 Length Hex
NPTF
1/4" B4FS25F2 1/4-18 16 18 20 22 23 25 26 27 2.14 0.75
3/8" B6FS37F5 3/8-18 41 46 50 55 59 63 66 69 2.50 .088
ACCESSORIES
1/2" B8FS50F8 1/2-14 65 73 80 87 93 99 704 109 3.12 1.06

3/4" B12FS75F13 3/4-14 105 118 130 141 152 161 169 177 3.68 1.38
1" B16FS100F21 1-11½ 170 191 210 227 245 260 273 286 1.75 1.75
1½" B24FS150F45 1½-11½ 365 410 450 489 525 557 586 615 5.86 2.50
All Flow Sensors have a pressure drop of approximately 2 psid at 80% of shut-off flow.
71
Accessories
In-Line Check Valves
1/4" to 2" nominal

(6.35 mm to 50.80 mm)
Rated Pressure

Size Thread Dimensions Rated Pressure
Part No.
(inch) NPTF A Hex PSI BAR
1/4 RA 04210 00 1/4-18 1.97 0.75 10,150 700
3/8 RA 04220 00 3/8-18 2.36 0.91 10,150 700
1/2 RA 04230 00 1/2-14 2.76 1.06 7,250 500
RA 4000 Series in-line check valves are designed 3/4 RA 04240 00 3/4-14 3.39 1.38 7,250 500
1.62
to allow flow of fluid in one direction only and limit the 1 RA 04250 00 1-11½ 3.94 7,250 500
2 RA 04290 00 2-11½ 5.91 2.95 4,350 300
line’s internal pressure (to the cracking pressure). They
are rugged and reliable, offer low pressure drop and have
elastomer valve seals for leak-free operation. Available
sizes are 1/4" to 2".
A
HEX
F eatures
• One-piece zinc plated steel body
• High strength steel valve provides excellent reliability under
severe operating conditions
• The valve has a captive nitrile (Buna-N) seal, assuring no
leakage at low and high pressures
• Low pressure drop versus flow rate BODY VALVE SPRING RETAINER
• Cracking pressure: 7 psi (0.5 bar)
• Cracking pressure is non-adjustable
• Contact supplier for availability of alternative cracking pressures
A pplications & I ndustries Pressure Drop vs. Flow Rate

• Agriculture • General Industry
1-1/4"
/2"
-1/2
1/4"
3/8"
1/2"
3/4"
• Construction • Fluid Transfer 100

1"
2"
11-1
90
• Hydraulic Tools • Oil and Gas
80
PRESSURE DROP, psi
PRESSURE, psi 70
60
50
*Cracking Pressure 40
(fully open) ±10%
30
Initial Opening Pressure
20
Re-closing Pressure 10
0
1 10 100 500
FLOW RATE, gpm FLOW RATE, gpm
* The cracking pressure corresponds to the full discharge
pressure (valve fully open) with a tolerance of ±10%.
72
Accessories
Flex-Air Fittings
ONE-WAY
Materials
• Integrated steel/polyurethane
construction
• Steel balls
• Buna-N (Nitrile) seal
• Thread sealant standard on
male NPTs
20° F to 140° F
TWO-WAY
The Flex-Air Fitting is designed to rotate
360° at up to a 75° angle. The Flex-Air Fitting helps
to alleviate Carpal Tunnel Syndrome and other stress
related injuries in the workplace.
F eatures
STRAIGHT-THRU
• Unique design provides free 360° rotation with up to a
75° flex angle in any direction
• Many styles and sizes available
• 145 psig (10 Bar) pressure rating (all models)
BENEFITS
• Provides flexibility of tool position to help alleviate CTS
(Carpal Tunnel Syndrome) and back stress resulting in
fewer lost-time injuries
• Minimizes paint damage
• Prevents kinking of air supply hose
GAS
• General Industry • Pnuematic Tools
ACCESSORIES
73
Accessories
Flex-Air Fittings
Female to Male Male to Male Industrial Plug to Male
Part Number FA25F25M Part Number FA25M25M Part Number FA25P25M

Inside Dia. 0.2” (5 mm) Inside Dia. 0.2” (5 mm) Inside Dia. 0.2” (5 mm)
1/4” NPT Female 1/4” NPT Male 1/4” Industrial Interchange
Connectors Connectors Connectors
1/4” NPT Male 1/4” NPT Male 1/4” NPT Male
Part Number FA37M37M Part Number FA37P25M

Inside Dia. 0.3” (7.5 mm) Inside Dia. 0.3” (7.5 mm)
Part Number FA25F37M
3/8” NPT Male 3/8” Industrial Interchange
Inside Dia. 0.3” (7.5 mm) Connectors Connectors
3/8” NPT Male 1/4” NPT Male
1/4” NPT Female
Connectors
3/8” NPT Male
ARO to Male RL Plug to Male
Part Number FA37F37M Part Number FA25AR25M Part Number FA3RL37M
Inside Dia. 0.3” (7.5 mm) Inside Dia. 0.2” (5 mm) Inside Dia. 0.3” (7.5 mm)
3/8” NPT Female ARO 210 Interchange 3/8” RL Plug

Connectors Connectors Connectors
3/8” NPT Male 1/4” NPT Male 3/8” NPT Male
Hose Barb to Male Lincoln to Male
Part Number FA37H37M Part Number FA25LI25M
Inside Dia. 0.3” (7.5 mm) Inside Dia. 0.2” (5 mm)
3/8” Barb Lincoln Interchange

Connectors Connectors
3/8” NPT Male 1/4” NPT Male
74
Accessories
Fittings
Hose Clamps (Brass) • Compression Type, Reusable

Male Pipe Thread Female Pipe Thread
(MPT) (FPT)
ONE-WAY
1/8-27 NPTF 3/8-18 NPTF 3/4-14 NPTF
Hose Part No. Hose Part No. Hose Part No.
I.D. O.D. MPT FPT I.D. O.D. MPT FPT I.D. O.D. MPT FPT
Series B 1/4" 15/32" 1B1 – Series B 1/4" 15/32" 4B1 – Series P 1/2" 13/16" 8P13 –
1/4" 1/2" 1B3 – 1/4" 1/2" 4B3 – 1/2" 7/8" 8P15 –
1/4" 9/16" 1B5 – 1/4" 9/16" 4B5 – Series R 3/4" 11/8" 8R23 –
1/4" 5/8" 1B7 – 1/4" 5/8" 4B7 – 3/4" 13/16" 8R25 –
Series C 5/16" 5/8" 4C7 – 3/4" 11/4" 8R27 –
5/16" 11/16" 4C9 –
Series D 3/8" 5/8" 4D7 5D7
TWO-WAY
1/4-18 NPTF 3/8" 11/16" 4D9 5D9
Hose Part No. 3/8" 3/4" 4D11 5D11 1-11½ NPTF
I.D. O.D. MPT FPT Hose Part No.
3/8" 7/8" 4D15 5D15
Series A 3/16" 7/16" 2A0 – I.D. O.D. MPT FPT
Series P 1/2" 13/16" 4P13 –
Series B 1/4" 15/32" 2B1 3B1 Series R 3/4" 11/8" 10R23 –
1/2" 7/8" 4P15 –
1/4" 1/2" 2B3 3B3 3/4" 13/16" 10R25 –
1/4" 9/16" 2B5 3B5 3/4" 11/4" 10R27 –
1/4" 5/8" 2B7 3B7
1/4" 11/16" 2B9 3B9 1/2-14 NPTF
Series C 5/16" 9/16" 2C5 – Hose Part No.
5/16" 5/8" 2C7 3C7 I.D. O.D. MPT FPT
STRAIGHT-THRU
5/16" 11/16" 2C9 – Series P 1/2" 13/16" 6P13 7P13
Series D 3/8" 5/8" 2D7 3D7 1/2" 7/8" 6P15 7P15
3/8" 11/16" 2D9 3D9 Series R 3/4" 11/8" 6R23 –
3/8" 3/4" 2D11 3D11 3/4" 13/16" 6R25 –
3/8" 7/8" 2D15 3D15 3/4" 11/4" 6R27 –
Series P 1/2" 13/16" 2P13 –
1/2" 7/8" 2P15 –
Swivel Nut Hose Clamps (Brass) • Compression Type, Reusable

With Brass Male Swivel Insert – External Seat (inverted flare) for use With Steel Female Swivel Insert, 37° Female Flare, for use with flared
with paint spray and oxygen fittings, etc. (Will accept 37° or 45° flare.) tube fittings.
GAS

9/16-18 Straight Thread
Hose Part
I.D. O.D. No. 7/16-20 Straight Thread 5/8-18 Straight Thread
Hose Part Hose Part
Series A 3/16" 7/16" 4LA0* I.D. O.D. No. I.D. O.D. No.
3/16" 7/16" 4RA0
Series B 1/4" 15/32" 720B1 Series D 3/8" 5/8" 2FD7
3/16" 1/2" 4LA3* 1/4-18 NPSM Straight Thread 1/4" 1/2" 720B3 3/8" 11/16" 2FD9
3/16" 1/2" 4RA3 Hose Part 1/4" 9/16" 720B5 3/8" 3/4" 2FD11
Series B 1/4" 15/32" 4RB1 I.D. O.D. No.
1/4" 5/8" 720B7
ACCESSORIES
1/4" 1/2" 4LB3* Series B 1/4" 15/32" 5RB1

1/4" 1/2" 4RB3 1/4" 1/2" 5RB3 9/16-18 Straight Thread 3/4-16 Straight Thread
1/4" 9/16" 4LB5* 1/4" 9/16" 5RB5 Hose Part Hose Part No.
1/4" 9/16" 4RB5 1/4" 5/8" 5RB7 I.D. O.D. No. I.D. O.D.
1/4" 5/8" 4RB7 Series C 5/16" 5/8" 5RC7 Series D 3/8" 11/16" 4FD9 Series P 1/2" 13/16" 1216P13
Series D 3/8" 5/8" 4RD7 Series D 3/8" 5/8" 5RD7 3/8" 3/4" 4FD11 1/2" 7/8" 1216P15
3/8" 11/16" 4RD9 3/8" 11/16" 5RD9 3/8" 7/8" 4FD11
3/8" 3/4" 4RD11 3/8" 3/4" 5RD11
* Left-hand thread for acetylene
service
75
Accessories
Fittings
Hose Stems Unions (Brass) Adapters
Hose Stem-to-Male Pipe Thread Part No. Part No.

Hose I.D. Thread Part No. Oxygen Adapter (Brass)
NPTF Brass Stainless H25MHU HHU25M Part No. Thread Size
3/16" 1/8-27 – LLS16 1/4" Male Pipe 1/4” Male Pipe Thread 9MBR 1/4-18 NPTF x 9/16-18 Right Hand
Union half
1/4" 1/8-27 SN17 – Thread Union
3/8" 1/8-27 SN18 – half consists of
1/4" 1/4-18 – LLS20 H25HMU01 body
5/16" 1/4-18 S205 – and 9028 o-ring.
3/8" 1/4-18 S21 –
1/2" 1/4-18 S22 –
1/4" 3/8-18 S23 –
3/8" 3/8-18 S24 LLS24
1/2" 3/8-18 S25 –
1/2" 1/2-14 S26 LLS26
3/4" 3/4-14 – LLS30 Pipe-to-Pipe Adapter (Brass)
1" 1-11½ – LLS35 Part No. Thread Size
19MBM 1/4-18 NPTF x 1/4-18 NPTF
Splicers (Brass) Part No. Part No.

H25HHU HHU25F
1/4" Hose Stem 1/4” Female Pipe
Union half consists Thread Union half
of H25HHU01 stem,
9028 o-ring and
Hose Stem-to-Hose Stem HUSN1 sleeve
Hose I.D. Part No.
1/4" HS31
5/16" HS32
3/8" HS33
1/2" HS34
Part No. Part No.

Hose Clamp-to-Hose Clamp H37HHU HHU37H
Hose I.D. Hose O.D. Part No. 3/8" Hose Stem 3/8” Hose Stem
1/4" 1/2" HSCB3 Union half consists Union half
5/16" 5/8" HSCC7 of H37HHU01 stem,
3/8" 11/16" HSCD9 9028 o-ring and
HUSN1 sleeve
Any union half shown on the left can be used with

any union half shown on the right.
All stainless steel fittings listed on this page are machined from Type 303 stainless steel bar stock.
76
Elastomer Selection Guide
Select seals compatible with the service intended for the couplings. Allowance must be made for the kind of
fluid to be conveyed and its temperature. Chemically active fluids will destroy some seal materials. Certain
seals withstand high temperatures, whereas others cannot. Use this elastomer selection guide to find the
appropriate seal. NOTE: Elastomer or seal material listed as “Standard” is furnished in most Eaton couplings.
Elastomers designated as “-118”, “-146”, “-192”, etc., are available as optional seal material for some
couplings. Other seal materials available upon request to suit requirements. Consult your local distributor.
NOTE: Service conditions may vary. The following information it is intended as a guide only and is not a guarantee.
Seal Information
Dash No. Compound
-*** Buna-N – 90 Durometer
-115 PTFE
-118 Neoprene
-143 Fluorocarbon
-146 Buna-N – 70 Durometer
-192* EPDM
-235† Kalrez
-236* EPDM
*** No Dash Number required for standard seal

material
* “-192” and “-236” compounds are not compatible
with mineral-based greases or oils
†Kalrez seals available by special quotation
EATON EATON
FLUID ELASTOMER FLUID ELASTOMER
Air (to 200° F) Standard Kerosene -146
Air (above 200° F) -143 Lindol -192▼
Acetone -192▼ L.P. Gases Standard
Acetylene Standard Methane -146
Alcohol, Ethyl -192▼ Methanol Standard
Alcohol, Methyl Standard Methyl Ethyl Ketone -192▼
Alkalies -192▼ Methyl Iso-Butyl Ketone -192▼
Ammonia, Anhydrous Standard MIL-H-5606A Standard
Ammonium Hydroxide -192▼ Mineral Spirits -146
Aroclor -143 Natural Gas Standard
Brake Fluid, Non-Petroleum Based -192▼ Nitrogen Standard
Butane -146 Octane -143
Carbon Dioxide Standard Oils, including: Animal, Mineral with Aniline Point Standard
Carbon Tetrachloride -143 above 160° F and Non-Food Service Vegetable
Cellulube -192▼ OS45 & OS45-1 -143
Creosote Standard Oxygen Service
Diesel Fuel -146 conditions
Diester Lubricants -143 dictate Elastomer
Ethane -146 Selection
Ethanol -192▼ Pentane -146
Ethylene Glycol -192▼ Perchloroethylene -143
Freon (most varieties) -118 Propane Standard
Gasoline, Aromatic & Non-Aromatic -143 Propylene -143
Glycerin Standard Pydraul -143
Helium Standard Steam (to 350° F) -192▼
Heptane -146 Steam (above 350° F) -236▼
Hexane -146 Stoddard Solvent -146
Houghto-Safe Series 200, 600, 5000 Standard Toluene -143
Houghto-Safe Series 1000 -192▼ Transmission Oil, Automotive Standard
Hydraulic Fluid, Petroleum-based with Aniline Standard Trichloroethylene -143
Point above 160° F Turpentine Standard
Hydrolube Standard Versilube F-50 -192▼
Jet Fuel (to 250° F) -146 Water (to 180° F) Standard
Jet Fuel (above 250° F) -143 Water (above 180° F) -192▼
▼ “-192” and “-236” compounds are not compatible with mineral-based greases or oils
77
TECHNICAL & WARRANTY INFORMATION Warranty
Every effort has been made to
have all photographs and drawings
accurately represent the products
About Industry Interchanges...It is possible to connect as they actually were at the time
two different manufacturers’ parts together so that they this catalog was printed. However,
in order to effectively continue
will effect a seal and work properly in a fluid system.
to meet the requirements of our
Eaton Coupling Group cannot guarantee the quality, users, changes in some items may
workmanship, dimensions, or tolerances of the other have been made during the life of
manufacturers’ parts, even though they might be inter- this catalog—which may be made
changeable. Therefore, whenever mixing parts, the final without notice.
assembly must always be tested before being put into
All Eaton Coupling products are
service. Failure to test could result in a sudden failure guaranteed to be free of defects
of the coupling causing severe personal injury or death. in material and workmanship for a
period of 90 days from the date of
shipment to a customer. Any claimed
Pressure Ratings** defect must be reported to the Eaton
Coupling Group in writing within
Since application conditions vary so widely, the pressures listed are the warranty period. This warranty
intended as a guide only and not a guarantee of performance. Pressure is limited to replacing or repairing,
peaks and extreme surge flows may cause a coupling to become at the Company’s option, f.o.b.
inoperative. the Company’s factory, any part
which upon Company inspection is
**NOTE! found to be defective. Components
Pressure ratings listed were determined by testing threaded sockets purchased by the Company from
and plugs. Sockets and plugs with hose stem and hose clamp end others are warranted only to the
connections are designed and recommended for use with shop air line extent of the guarantee or warranty,
pressure only (150 psig maximum) when used with the appropriate if any, made to the Company.
style hose.
THE ABOVE WARRANTY COMPRISES

THE COMPANY’S SOLE AND ENTIRE
WARRANTY OBLIGATION AND
LIABILITY IN CONNECTION WITH
Over-pressurization could Couplings do wear out. In EATON. ALL OTHER WARRANTIES,
result in a sudden failure of order to avoid severe bodily EXPRESS OR IMPLIED, INCLUDING,
the coupling causing severe injury or death, couplings WITHOUT LIMITATION, WARRANTIES
bodily injury or death. Be must be routinely checked OR MERCHANTABILITY AND FITNESS
sure to select the proper cou- for condition and replaced FOR A PARTICULAR PURPOSE,
pling for your application and if necessary. ARE EXPRESSLY EXCLUDED. THE
use it only within the speci- COMPANY IN NO EVENT SHALL
fied service pressure range.
BE LIABLE FOR INDIRECT OR
CONSEQUENTIAL DAMAGES ARISING
OUT OF THE SALE OR USE OF
EATON COUPLINGS.
78
Eaton Eaton Eaton Eaton
Hydraulics Group USA Hydraulics Group USA Hydraulics Group Europe Hydraulics Group Asia Pacific
1000 W. Bagley Road
Berea, OH 44017
14615 Lone Oak Road
Eden Prairie, MN 55344
Route de la Longeraie 7
1110 Morges
Full Line Catalog
Eaton Building
4th Floor, No. 3 Lane 280 Linhong Rd.
USA USA Switzerland Changning District
Tel: 440-826-1115 Tel: 952-937-9800 Tel: +41 (0) 21 811 4600 Shanghai 200335
Fax: 440-826-1105 Fax: 952-294-7722 Fax: +41 (0) 21 811 4601 China
www.eaton.com/hydraulics www.eaton.com/hydraulics Tel: (+86 21) 5200 0099
Fax: (+86 21) 5200 0400
© 2010 Eaton Corporation

All Rights Reserved
Printed in USA
June 2011

Quick Connect Coupling Catalog: Eaton Hansen

Uploaded by

Copyright:

Available Formats

Quick Connect Coupling Catalog: Eaton Hansen

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Quick Connect Coupling Catalog: Eaton Hansen

Uploaded by

Copyright:

Available Formats

Eaton® Hansen™

Quick Connect Coupling Catalog

One-Way Shutoff Couplings Straight Through Couplings

Two-Way Shutoff Couplings Index

EXAMPLE: 1000 – BV – SL – 143 – OC

CLEANING AND LUBRICATION PROCESS FOR GASEOUS OR OXYGEN SERVICE

Over-pressurization could Couplings do wear out.

Aerospace Agriculture Breathing Carpet Chemical

Construction Defense Energy Food and General

Heating/Cooling/ Injection Marine Medical Mining

Petrochemical Pharmaceutical Recreation Transportation Water and

Eaton is Proud to Hold the

PROUD MEMBERS OF:

STEEL (Zinc/chromate Finish)

SEAL MATERIALS (Various)

DUST CAP (Vinyl)

1/4" 1/4" 1/4" 1/4" 3/8"

attached, which helps prevent user strain and fatigue,

• The socket can accept multiple plug configurations, making it

• Air Tools • General Pneumatics 24CC

Part Body Thread Rated

3CC37F 3/8" 3/8" Female NPT 60 SCFM Industrial, ARO 310

3CC50F 3/8" 1/2" Female NPT 60 SCFM Industrial, ARO 310

24CC25F 1/4" 1/4" Female NPT 53 SCFM CEJN 320, Rectus 25

24CC37F 1/4" 3/8" Female NPT 53 SCFM CEJN 320, Rectus 25

Shown with optional sleeve lock

Dimensions Female End Connections Part No. Dimensions

Dimensions Hose Stem End Connections Part No. Dimensions

Optional Seal Materials: 138-Silicone, 143-Fluorocarbon, 192-EPDM

Female End Connections Part No. Dimensions

† With Bleeder Ball Check – Reduces hose whip when disconnecting

Dust Plugs Accessories:

Dimensions Female End Connections Part No. Dimensions

† With Bleeder Ball Check – Reduces hose whip when disconnecting

Optional Seal Materials: 143-Fluorocarbon, 192-EPDM

• Industrial Breathing Air • Maintenance & Repair Flow Capacity

Shown with optional sleeve lock.

Female End Connections Part No. Dimensions

Optional Seal Materials: 138-Silicone, 143-Fluorocarbon, 192-EPDM

Dimensions Female End Connections Part No. Dimensions

† With Bleeder Ball Check – Reduces hose whip when disconnecting

Optional Seal Materials: 138-Silicone, 143-Fluorocarbon, 192-EPDM

Part No. Dimensions Female End Connections Part No. Dimensions

† With Bleeder Ball Check – Reduces hose whip when disconnecting

Optional Seal Materials: 143-Fluorocarbon, 192-EPDM

Part No. Dimensions Female End Connections Part No. Dimensions

Hose Stem End Connections Part No. Dimensions

70GA† 1/2" 3.53 1.12

† With Bleeder Ball Check – Reduces hose whip when disconnecting

Dust Caps and Dust Plugs Accessories:

Optional Seal Materials: 143-Fluorocarbon, 192-EPDM

P30 & P40 Series

Auto-Flo 23 & 24 Series

A pplications & markets -40° F to 250° F

with 5 psi pressure

Dimensions Female End Connections Part No. Dimensions

Dimensions Hose Stem End Connections Part No. Dimensions

• Light weight, compact ergonomic design

• General Pneumatics Female End