1

GPS Vehicle Tracker

(GPS+GSM+SMS/GPRS)
User Manual

Preface
Thank you for purchasing the tracker. This manual shows how to operate the device smoothly and
correctly. Make sure to read this manual carefully before using this product. Please note that
specification and information are subject to changes without prior notice in this manual. Any
change will be integrated in the latest release. The manufacturer assumes no responsibility for any
errors or omissions in this document.
 2

1. Product packaging accessories:

1.1 power 4P line 1pc (standard accessory)
1.4 electric relay 1pc (optional accessory)
1.5 User manual 1pc (standard accessory)
(Accessories products refer to the actual product)

2. Product features：
2.1 GSM four frequency(GSM850/900/1800/1900MHZ) system global general;
2.2 built-in switching power supply, exceed wide voltage input range: 9-75 VDC;
2.3 GPS continuous GPS positioning, GPRS report regularly;
2.4 Support SMS message to check the location info;
2.5 built-in vibration sensor, realization vehicle anti-theft intelligently;
2.6 ACC the ignition signal detection,vehicle status prompted;
2.7 waterproof designed
2.11 built-in backup battery, realize the illegal cut the line alarm;

Content Specs.
Dim. 68mm x 40mm x 20mm
Weight 90g
Network GSM/GPRS
Band 850/900/1800/1900Mhz
GPS chip UBLOX
GPS sensitivity -159dBm
GPS accuracy 10m
Cold status 35-80s
Time To First Fix Warm status 35s
Hot status 1s
9－75V input
voltage input

Battery Build-in 3.7V 370mAh Li-ion battery

Storage Temp. -40°C to +85°C
Operation Temp. -20°C to +55°C
Humidity 5%--95% non-condensing

Functions:
1. GPS and Location Based Service
Location Based service also named A-GPS, when tracker in underground or tunnel ,can get location
by AGPS.
2. Real time tracking
Real time tracking it by cell phone and platform . Also can support get location every 5 seconds,
and the GPS accuracy is 5m .
3. Check the history of route on platform
Can check and replay within one year history of route of device ,by web monitor center
 3

4. Power Saving Mode

The device go into standby mode when there isn’t vibration for 3 minutes , it will go into working
mode when it feel vibration
5.Google map on mobile
Check the location with google map on mobile.
6. Geofence and movement alert
Set up a geo-fence for the unit to restrict its movements within a district ,unit will send a message to
the authorized numberwhen it breaches the district..
7.Low Battery Alarm
4. Appearance scheme

Hang hole

LED
Light
SIM Card slot
USB port

Waterproof cover
 4

5. Preparation Installation
5.1.. Check the product
5.1.1 Open the package, and check product model and accessories. If there is something wrong or
missing, please contact the distributor.
5.1.2. The selection of SIM card must follow the distributor’s suggestion.
5.1.3. Install SIM card
Firstly, open the cover of the waterproof , secondly, insert the card ; finally, recover the
waterproof cover

1. 2. 3. 4.

Tips:
Don't insert the SIM card up-side-down.·
Make sure the SIM card with GPRS service.
If the SIM card has been inserted, but it requires you to input SIM PIN, please close the
SIM PIN function under the instruction of your mobile phone user ’s manual.
Make sure the SIM card account has enough money

5.2. Installation
Install the tracker is hidden installation, you'd better to install it with the help of professional
companies or workers authorized by the distributor. Please install it according to the following
instruction.
5.2.1.To avoid the thief’s destruction, the tracker should be installed in a hidden place.
5.2.2 Don't put the tracker together with the emission sources, such as the parking radar system,
alarms and other vehicle-carried communication terminals.
5.2.3 You can fix the tracker with the cable tie, or glue it with wide strong sponge double-sided tapes.
5.2.4 Because the tracker has GSM and GPS antenna inside, please make sure the reception side
of GPS is upward (facing the sky), and there is no metal shelter above the tracker.
Suggestions are as follow:
a, Hidden area under the decoration board below the front windshield or back windshield;
b, Hidden area around the front panel (with a surface made of non-metal materials);
Attention: If there is a metal insulation or a heating layer glued in the windshield, it will reduce the
efficiency of GPS signal reception, and the GPS can’t work well, you need to find other places to
 5

install again.

5.4 Terminal wiring diagram

Relay connectted
 6

6. Equipment connect the matters needing attention

Power supply, the original car guard against theft, broken oil and electricity control line (4 pin)
6.1 This equipment is standard for power supply 10V-75VDC, please choose the original provide power
supply cord, red line power positive, the black line for power negative; When installation, please
choose to separate negative power grounding wires or by iron, don't and other ground were
answered
6.2 The original car security line (Orange line)

7. Terminal parameter setting

Message set data: The car owner’s mobile phone No. send the message code to the SIM card of
the GPS device. Separated symbols is comma. The commas of the following functions data setting
command is the English input format.
7.1 Basic operation Settings
7.1.1 Special No. setting (i.e., the owner number) ：
Special No. is the alarm No. You can send the command of adding special No. message to terminal
for adding the No. Under the status of alarm, the terminal will send the position message to the setting
special No. and call the No. repeat till the phone is connected.
7.1.1.1 Add the special No.：
Command format：adm+ code+ comma+NO. e.g.：adm123456,138********
Reply message：ADM！A1：138********
7.1.1.2 Delete special number：
Command format：noadmin+ code+ comma e.g.：adm123456，
Reply message：ADM！A1：
7.1.2 Modify the terminal password: please remember the password, if forget available owner send
factory default command center number
The default terminal password：123456
Command format：pwd123456 666888(666888 for the new password,must be 6 to digital)
Reply message：OK! New password: ******. Safe keeping!
P.S.: the following instructions will send can achieve center number, be sure to keep in mind

7.2 Anti-theft alarm location query set

7.2.1 Location query
Command format：G123456# or where
Reply message：<DateTime:10-11-18 18:41:04>
http://maps.google.com/maps?q=N22.540885,E113.951341
 7
7.2.2 Removal and fortify
7.2.2.1 Fortified Command format：SF or 111
Reply message：GSM:A/B/C/D. POWER:X. Arm delay in XXS！
7.2.2.2 Removal Command format：CF or 000
Reply message：GSM:A/B/C/D. POWER:X. DISARMED！
P.S.：The GSM signal 0 is no signal
7.2.3 Rest for 10 minutes automatic fortification (default open)
7.2.3.1 Open Command format：auto1
Reply message：Auto arm by Standby 10 mins：ON
7.2.3.2 Close Command format：auto0
Reply message：Auto arm by Standby 10 mins：OFF
Spd:XXXkm/h 2013-07-11 21:54:33
7.2.5 Vibration alarm setting
Continuous vibration time for 3 seconds by default,vibration alarm time interval 5 minutes by
default
Alarm way：1 = SMS, 2 = phone call, 3 = SMS + Call , 0 = closed
Command format：vib2,3
Reply message：OK! Vibration Level:X Alarm mode: Call/SMS/Call & SMS
Alarm content：Vibration！Please check it now! Lat: Lon: GPS:A/V 2013-07-20 16:23
7.2.6 Shift alarm setting(default open)
7.2.6.1 Open Command format：move300
Reply message：OK! Move alarm: on
7.2.6.2 Close Connand format：move0
Reply message：OK! Move alarm:OFF
7.2.7 Over speed alarm(default close)
7.2.7.1 Open Command format：spd080
Reply message：OK! Over speed alarm: km/h
7.2.7.2 Close Connand format：spd0
Reply message：OK! Over speed alarm: off
Over speed alarm content：Over speed alarm！
http://maps.google.com/maps?q=22.53908%2c113.90871 Spd:XXXkm/h 2013-07-11 21:54:33
P.S.: set the range value of 050-300, speed limit 3 digits, the unit is km/hour
7.2.8 Oil outage & power outage
7.2.8.1 cutting off the oil
Command format：555
Reply message：CUT OIL OK!
7.2.8.2 opening the oil
Command format：666
Reply message：RESUME OIL OK!
When the car is stolen, the monitor platform will send the command of Oil cut-off power outages.
For keeping the car safe drive the oil of the stolen car is cut off and the car can not be started.
P.S ： In order to keep the car safe, the terminal is only under GPS effective position status and
make sure the car is less than 20km/h or the car is still, the oil outage and power outage can be
operated .when the theft alarm is relieved, the monitor platform restore the oil & power command,
the terminal recover the oil & power and you can go on driving the car.
P.S.: Make sure to set the special No. before achieving this function

7.3 Equipment to restore the query set

7.3.1 Recover the factory setting:
Command format：format
Reply message：The tracker will immediately restore the factory settings. All previous settings will
be canceled.
7.3.2 GPS re-start:
Command format：RST
Reply message：The tracker will immediately restart!

7.4 commands list(pls note 123456 is the default password)

Feature name Active command Reply Cancel command reply
 8
Begin(blank Begin123456 Begin ok
before set)
Admin number Admin123456+s Admin ok Noadmin123456 Noadmin ok
pace+number +space+number
Password Password123456 Password ok
+space+new
Sever ip&port Adminip123456 Adminip ok
+space+ip+space
+port
APN Apn123456+loca Apn ok
l apn content
LBS Addjz=1 Open LBS Addjz=0 Close LBS

GPRS Gprs123456 Gprs ok Nogprs123456 Nogprs ok

Time Zone Timezone123456 Timezone ok Timezone123456 Timezone ok

+space+8 +space+-8
Language Lag1 Switched to
english
Restore factory format No reply
setting
Upload Upload123456+ti Upload ok
frequency(10-60 me
0s)
Sleep working Sleep123456+sp Sleep time ok Wake up by
mode ace+time sms,call,press
button
Shock working Sleep123456+sp Sleep shock ok Wake up by
mode ace+shock shock,sms,call,pr
ess button
No sleep Nosleep123456 Nosleep ok
working mode
Get location Where or Google map link
G123456#
Shock alarm Shock123456 Shock ok Noshock123456 Noshock ok

Shock call alarm vibcall123456 Shock call alarm

ok
Shock sms alarm vibsms123456 Shock sms alarm
ok
Move Move123456+sp Move ok Nomove123456 Nomove ok
alarm(distance:1 ace+distance
00-5000m)
Overspeed Speed123456+sp Speed ok Nospeed123456 Nospeed ok
alarm(50-120km/ ace+max speed
h)
Set a geo-fence stockade+123456 stockade ok nostockade12345 Nostockade ok
 9
(stockade) +space+long,lat;l 6
ong,lat
Check setting of Param1 Software Param2 Admin
device version,date,imei number,sos
,ip&port,apn,web number,move
platform distance,speed,et
c
Status of device status Bat:4,gprs:1.gsm
:3,gsm:1,acc:0,oi
l:0,power:1,s:0
7.5 Web platform and sever ip&port
Website Sever IP Port
www.lkgps.net 101.1.16.228 7700
8.App download
8.1 android version: scan below QR code

8.2 ios version: search “LKGPS” in app store

9. Faults & The solutions

 10

Faults Solution

Startup Fail Check the battery and see if it is fully charged or

correctly installed.
Hang up Fail In existence of an authorized number, an unauthorized
number dials up the unit. Please initialize the unit and re-set up
the authorized numbers.

Monitoring failure Please check the authorization number is set to the correct time

Please make sure SIM Card is GSM Net and installed correctly; also
No GSM Signal
call display should be on; but no call transfer and PIN code off.