Cisco vs Huawei CLI command

Cisco Vendor Huawei Vendor

Basic Commands
User Mode
User View
Enable Mode
System View
Globle Configuration Mode
Interface View
Interface Mode
show
display
exit
quit
end
return
Ctrl+Z
Ctrl+Z
Ctrl+A
Ctrl+A
Ctrl+E
Ctrl+E
Ctrl+U
Ctrl+U
Ctrl+P
Ctrl+P
Ctrl+N
Ctrl+N
no
undo
hostname
sysname
traceroute
tracert
ping
ping
encapsulation
link-protocol
clock rate
baudrate
copy running-config startup-config OR write
save
memory
reset saved-configuration
write erase
reboot
reload
clock datetime 12:00:00 2018-06-01
clock set 12:00:00 01 Jun 2018
sysview
configure terminal
header shell information
banner motd
Show Commands
Cisco# show ip interface brief <Hauwei> display ip interface brief
Cisco# show interface serial 1/0/0 <Hauwei> display interface serial 1/0/0
Cisco# show version <Hauwei> display version
Cisco# show history <Hauwei> display history-command
Cisco# show running-config <Hauwei> display current-configuration
Cisco# show startup-config <Hauwei> display saved-configuration
Cisco# show flash <Hauwei> dir
Cisco# show user <Hauwei> display users
Cisco# show line <Hauwei> display user-interface
Cisco# show clock <Hauwei> display clock
Cisco# show interface FastEthernet 0/0 <Hauwei> display interface FastEthernet 0/0
Cisco# show ip interface FastEthernet 0/0 <Hauwei> display ip interface FastEthernet
Cisco# show running-config interface 0/0
FastEthernet 0/0 <Hauwei> display current-configuration
Cisco# show ip route interface FastEthernet 0/0
Cisco# show ip route rip <Hauwei> display ip routing-table
Cisco# show ip protocols <Hauwei> display ip routing-table protocol
Cisco# show ip ospf interface serial 1/0 rip
Cisco# show ip ospf neighbor <Hauwei> display rip
Cisco# show access-list <Hauwei> display ospf interfaceserial 1/0
Cisco# show access-list 10 <Hauwei> display ospf peer
Cisco# show ip nat translations <Hauwei> display acl all
Cisco# show mac address-table <Hauwei> display acl 2001
Cisco# show vlan <Hauwei> display nat session all
Cisco# show vlan id 1 <Hauwei> display mac-address
Cisco# show interface status <Hauwei> display vlan
Cisco# show spanning-tree <Hauwei> display vlan 1
Cisco# show ipv6 interface brief <Hauwei> display port vlan
Cisco# show ipv6 route <Hauwei> display stp
Cisco# show frame-relay map <Hauwei> display ipv6 interface brief
Cisco# show ip bgp neighbor <Hauwei> display ipv6 routing-table
Cisco# show ip bgp summary <Hauwei> display fr map-info
Cisco# show bgp ipv4 unicast summary <Hauwei> display bgp peer
Cisco# show bgp ipv6 unicast summary <Hauwei> display ip routing-table protocol
Cisco# show bgp vpnv4 unicast all summary bgp
Cisco# show bgp vpnv6 unicast all summary <Hauwei> display bgp routing-table
<Hauwei> display bgp ipv6 routing-table
<Hauwei> display bgp vpnv4 all routing-
table
<Hauwei> display bgp vpnv6 all routing-
table
Console Password and Telnet Password
<Hauwei> system-view
[Hauwei-line-console0] user-interface
console 0
Cisco# configure terminal [Hauwei-line-console0] set authentication
Cisco(config)# line console 0 password simple Huawei
Cisco(config-line)# password Cisco [Hauwei-line-console0] authentication-mode
Cisco(config-line)# login password
Cisco(config-line)# line vty 0 4 [Hauwei] user-interface vty 0 4
Cisco(config-line)# password Cisco [Hauwei-line-vty0-4] set authentication
Cisco(config-line)# login password simple Huawei
Cisco(config-line)# privilege level 15 [Hauwei-line-vty0-4] authentication-mod
password
[Hauwei-line-vty0-4] user privilege level
15
Configure IP address IPv4
Cisco# configure terminal <Hauwei> system-view
Cisco(config)# interface fastethernet 0/0 [Hauwei] interface fastethernet 0/0
Cisco(config-if)# ip addr 192.168.0.1 [Hauwei-fastethnet0/0] ip addr 192.168.0.1
255.255.255.0 24
Cisco(config-if)# no shutdown [Hauwei-fastethnet0/0] undo shutdown
Cisco(config-if)# exit [Hauwei-fastethnet0/0] quit
Configure IPv6
<Hauwei> system-view
Cisco# configure terminal
[Hauwei] ipv6
Cisco(config)# ipv6 unicast-routing
[Hauwei] interface serial 1/0/0
Cisco(config)# interface fastethernet 0/0
[Hauwei-serial0/0/0] ipv6 enable
Cisco(config-if)# ipv6 enable
[Hauwei-serial0/0/0] ipv6 address
Cisco(config-if)# ipv6 address2001::1/64
2002::1/64
Cisco(config-if)# exit
[Hauwei-serial0/0/0] quit
Cisco# show ipv6 interface brief
<Hauwei> display ipv6 interface brief
Cisco# show ipv6 route
<Hauwei> display ipv6 routing-table
Configure Serial Interface
Cisco# configure terminal
<Hauwei> system-view
Cisco(config)# interface serial 1/0/0
[Hauwei] interface serial 1/0/0
Cisco(config-if)# ip addr 172.16.0.1
[Hauwei-serial1/0/0] ip addr 172.16.0.1 16
255.255.0.0
[Hauwei-serial1/0/0] link-protocol ppp
Cisco(config-if)# encapsulation ppp
[Hauwei-serial1/0/0] baudrate 64000
Cisco(config-if)# clock rate 64000
[Hauwei-serial1/0/0] undo shutdown
Cisco(config-if)# no shutdown
[Hauwei-serial1/0/0] quit
Cisco(config-if)# exit
Configure VLANs
Cisco# configure terminal <Hauwei> system-view
Enter configuration commands, one per line. Enter system view, return user view with
End with CNTL/Z. Ctrl+Z
Cisco(config)# vlan 10 [Hauwei] vlan 10
Cisco(config-vlan)# name CORP_NET [Hauwei-vlan10] description CORP_NET
Cisco(config-vlan)# end [Hauwei-vlan10] return
Cisco# show vlan brief <Hauwei> display vlan OR display vlan 10
Configure Access Port
<Hauwei> system-view
Cisco# configure terminal
[Hauwei] interface Ethernet 0/0/0
Cisco(config)# interface Ethernet 0/0/0
[Hauwei-Ethernet0/0/0] port link-type
Cisco(config-if)# switch mode access
access
Cisco(config-if)# switchport access vlan 10
[Hauwei-Ethernet0/0/0] port default vlan 10
Cisco(config-if)# end [Hauwei-Ethernet0/0/0] return
Cisco# show vlan brief <Hauwei> display vlan 10
Configure Trunk Port
Cisco# configure terminal <Hauwei> system-view
Cisco(config)# interface Ethernet 0/0/0 [Hauwei] interface Ethernet 0/0/0
Cisco(config-if)# switch mode trunk [Hauwei-Ethernet0/0/0] port link-type trunk
Cisco(config-if)# switchport trunk [Hauwei-Ethernet0/0/0] port trunk allow-
encapsulation dot1q pass vlan all
Cisco(config-if)# end [Hauwei-Ethernet0/0/0] return
Cisco# show interface trunk <Hauwei> display port vlan Ethernet 0/0/0
Cisco# show interface status <Hauwei> display port vlan
Configure Inter-VLAN Routing
Cisco# configure terminal
<Hauwei> system-view
Cisco(config)# interface GigabitEthernet
[Hauwei] interface GigabitEthernet 0/0
0/0
[Hauwei-GigabitEthernet 0/0] undo shutdown
Cisco(config-if)# no shutdown
[Hauwei-GigabitEthernet 0/0] quit
Cisco(config-if)# exit
[Hauwei] interface GigabitEthernet 0/0.10
Cisco(config)# interface GigabitEthernet
[Hauwei-GigabitEthernet 0/0.10] vlan-type
0/0.10
dot1q 10
Cisco(config-if)# encapsulation dot1Q 10
[Hauwei-GigabitEthernet 0/0.10] ip addr
Cisco(config-if)# ip addr 10.1.1.1
10.1.1.1 255.0.0.0
255.0.0.0
[Hauwei-GigabitEthernet 0/0.10] quit
Cisco(config-if)# end
[Hauwei] interface GigabitEthernet 0/0.20
Cisco(config)# interface GigabitEthernet
[Hauwei-GigabitEthernet 0/0.20] vlan-type
0/0.20
dot1q 20
Cisco(config-if)# encapsulation dot1Q 20
[Hauwei-GigabitEthernet 0/0.20] ip addr
Cisco(config-if)# ip addr 20.1.1.1
20.1.1.1 255.0.0.0
255.0.0.0
[Hauwei-GigabitEthernet 0/0.20] quit
Cisco(config-if)# end
Administrative Distance Values
Route Source Administrative Distance Route Source Preference
Connected 0 Direct 0
OSPF 110 OSPF 10
IS-IS 115 IS-IS 15
Static 1 Static 60
RIP 120 RIP 100
Configure RIP Routing Protocol
Cisco# configure terminal <Hauwei> system-view
Cisco(config)# router rip [Hauwei] rip 1
Cisco(config-router)# version 2 [Hauwei-rip-1] version 2
Cisco(config-router)# network 192.168.0.0 [Hauwei-rip-1] network 192.168.0.0
Cisco(config-router)# network 172.16.0.0 [Hauwei-rip-1] network 172.16.0.0
Cisco(config-router)# distance 75 [Hauwei-rip-1] preference 75
Cisco(config-router)# end [Hauwei-rip-1] return
Configure RIPng
Cisco# configure terminal <Hauwei> system-view
Cisco(config)# ipv6 route rip 1 [Hauwei] ripng 1
Cisco(config-rtr)# exit [Hauwei-ripng-1] quit
Cisco(config)# interface GigabitEthernet [Hauwei] interface GigabitEthernet 0/0
0/0 [Hauwei-GagabitEthernet0/0] ripng 1 enable
Cisco(config-if)# ipv6 rip 1 enable [Hauwei-GagabitEthernet0/0] quit
Cisco(config-if)# end [Hauwei] Serial 1/0
Cisco(config)# interface Serial 1/0 [Hauwei-Serial1/0] ripng 1 enable
Cisco(config-if)# ipv6 rip 1 enable [Hauwei-Serial1/0] return
Cisco(config-if)# exit <Hauwei> display ipv6 routing-table
Cisco# show ipv6 route rip protocol rip
Configure OSPF Routing Protocol
Cisco> enable <Hauwei> system-view
Cisco# configure terminal [Hauwei] ospf 1
Cisco(config)# router ospf 1 [Hauwei-ospf-1] area 0
Cisco(config-router)# network 192.168.1.0 [Hauwei-ospf-area-0.0.0.0] network
0.255.255.255 area 0 192.168.1.0 0.255.255.255
Cisco(config-router)# network 172.16.0.0 [Hauwei-ospf-1] area 1
0.0.255.255 area 1 [Hauwei-ospf-area-0.0.0.1] network
Cisco(config-router)# end 172.16.0.0 0.0.255.255 area 1
Cisco# show ip ospf interface serial 1/0 [Hauwei-ospf-area-0.0.0.1] return
Cisco# show ip ospf <Hauwei> display ospf interface serial 1/0
Cisco# show ip ospf neighbor <Hauwei> display ospf 1 brief
Cisco# show ip route ospf <Hauwei> display ospf peer
<Hauwei> display ip routing-table protocol
ospf
Configure OSPfv3
Cisco# configure terminal <Hauwei> system-view
Cisco(config)# ipv6 router ospf 1 [Hauwei] ospfv3 1
Cisco(config-rtr)# router-id 10.10.10.1 [Hauwei-ospfv3-1] router-id 10.10.10.1
Cisco(config-rtr)#exit [Hauwei-ospfv3-1] quit
Cisco(config)# interface gigabitEthernet [Hauwei] interface gigabitEthernet 1/0
1/0 [Hauwei-giabitEthernet1/0] ospfv3 1 area 0
Cisco(config-if)# ipv6 ospf 1 area 0 [Hauwei-giabitEthernet1/0] quit
Cisco(config-if)# exit [Hauwei] interface serial 1/0
Cisco(config)# interface serial 1/0 [Hauwei-serial1/0] ospfv3 1 area 1
Cisco(config-if)# ipv6 ospf 1 area 1 [Hauwei-serial1/0] return
Cisco(config-if)# end <Hauwei> display ospfv3 1
Cisco# show ipv6 protocol <Hauwei>display ipv6 routing-table protocol
Cisco# show ipv6 route rip rip
Configure Static Route Protocol
Cisco# configure terminal <Hauwei> system-view
Cisco(config)# ip route 10.10.10.0 [Hauwei] ip route-static 10.10.10.0
255.255.255.0 172.16.1.1 255.255.255.0 172.16.1.1
Cisco(config)# exit [Hauwei] quit
Cisco# show ip route <Hauwei> display ip routing-table
Configure IPv6 Static Routing Protocol
<Hauwei> system-view
Cisco# configure terminal
[Hauwei] ipv6 route-static 2003::/64
Cisco(config)# ipv6 unicast-routing
2002::2
Cisco(config)# ipv6 route 2003::/64 2002::2
[Hauwei] quit
Cisco(config)# exit
<Hauwei> display ipv6 interface brief
Cisco# show ipv6 interface brief
<Hauwei> display ipv6 routing-table
Cisco# show ipv6 route
<Hauwei> display ipv6 routing-table
Cisco# show ipv6 static route
protocol static
Configure Static NAT
<Hauwei> system-view
Cisco> enable [Hauwei] interface fastEthernet 0/0
Cisco# configure terminal [Hauwei-fastEthernet0/0] nat static global
Cisco(config)# ip nat inside source static 10.1.1.1 inside 172.16.20.1 netmask
172.16.20.1 10.1.1.1 255.255.255.255
Cisco(config)# ip nat inside source static [Hauwei-fastEthernet0/0] quit
172.16.20.2 10.1.1.2 [Hauwei] interface serial 1/0
Cisco(config)# interface fastEthernet 0/0 [Hauwei-serial1/0] nat static global
Cisco(config-if)# ip nat inside 10.1.1.2 inside 172.16.20.2 netmask
Cisco(config-if)# exit 255.255.255.255
Cisco(config)# interface serial 1/0 [Hauwei-serial1/0] return
Cisco(config-if)# ip nat inside <Hauwei> display nat session all
Cisco(config-if)# end <Hauwei> display nat static
Cisco# show ip nat translations <Hauwei> display nat static interface
serial 1/0
Configure NAT Overloading PAT
DEFINING NAT DEFINING NAT
Cisco# configure terminal <Hauwei> system-view
Cisco(config)# access-list 20 permit [Hauwei] acl 2012
172.20.1.0 0.255.255.255 [Hauwei-acl-basic-2012] rule permit source
Cisco(config)# ip nat pool CORP_POOL 172.20.1.0 0.0.0.255
10.1.1.2 10.1.1.2 netmash 255.0.0.0 [Hauwei-acl-basic-2012] quit
Cisco(config)# ip nat inside source list 20 [Hauwei] nat address-group 1 10.1.1.2
pool CORP_POOL overload 10.1.1.2
APPLYING NAT APPLYING NAT
Cisco(config)# interface fastEthernet 0/0 [Hauwei] interface serial 1/0/0
Cisco(config-if)# ip nat inside [Hauwei-serial1/0/0] nat outbound 2012
Cisco(config-if)# end address-group 1
Cisco(config)# interface serial 1/0/0 [Hauwei-serial1/0/0] return
Cisco(config-if)# ip nat outside
Cisco(config-if)# end
Configure Standard and Basic ACL
<Hauwei> system-view
[Hauwei] acl 2001
[Hauwei-acl-basic-2001] rule permit source
5.5.5.5 0.0.0.0
[Hauwei-acl-basic-2001] quit
[Hauwei] traffic classifier tc
[Hauwei-classifier-tc] if-match acl 2001
[Hauwei-classifier-tc] quit
[Hauwei] traffic behavior tb
Cisco# configure terminal
[Hauwei-behavior-tb] deny
Cisco(config)# access-list 10 deny 5.5.5.5
[Hauwei-behavior-tb] quit
0.0.0.0
[Hauwei] traffic policy tp
Cisco(config)# access-list 10 permit any
[Hauwei-trafficpolocy-tp] deny
Cisco(config)# interface serial 1/0/0
[Hauwei-trafficpolocy-tp] quit
Cisco(config-if)# ip access-group 10 in
[Hauwei] interface serial 1/0/0
Cisco(config-if)# end
[Hauwei-serial1/0/0] traffic-policy tp
Cisco# show access-lists
inbound
Cisco# show access-lists 10
[Hauwei-serial1/0/0] return
<Hauwei> display acl all
<Hauwei> display acl 2001
<Hauwei> display traffic classifier user-
defined tc
<Hauwei> display traffic behavior user-
defined tb
<Hauwei> display traffic policy user-
defined tp
Configure Extended/Advanced ACL
<Hauwei> system-view
[Hauwei] acl 3001
[Hauwei-acl-adv-3001] rule permit tcp
source 5.5.5.1 0.0.0.0 destination 5.5.5.2
0.0.0.0 destinatio-port eq telnet
[Hauwei-acl-adv-3001] quit
[Hauwei] traffic classifier tc
[Hauwei-classifier-tc] if-match acl 3001
[Hauwei-classifier-tc] quit
Cisco# configure terminal [Hauwei] traffic behavior tb
Cisco(config)# access-list 110 deny tcp [Hauwei-behavior-tb] deny
5.5.5.1 0.0.0.0 5.5.5.2 0.0.0.0 eq 23 [Hauwei-behavior-tb] quit
Cisco(config)# access-list 110 permit ip [Hauwei] traffic policy tp
any any [Hauwei-trafficpolocy-tp] classifier tc
Cisco(config)# interface serial 1/0/0 behavior tb
Cisco(config-if)# ip access-group 110 in [Hauwei-trafficpolocy-tp] quit
Cisco(config-if)# end [Hauwei] interface serial 1/0/0
Cisco# show access-lists [Hauwei-serial1/0/0] traffic-policy tp
Cisco# show access-lists 110 inbound
[Hauwei-serial1/0/0] return
<Hauwei> display acl all
<Hauwei> display acl 3001
<Hauwei> display traffic classifier user-
defined tc
<Hauwei> display traffic behavior user-
defined tb
<Hauwei> display traffic policy user-
defined tp
Configure Frame-Relay – Static Mapping
Cisco# configure terminal <Hauwei> system-view
Cisco(config)# interface serial 1/0/0 [Hauwei] interface serial 1/0/0
Cisco(config-if)# encapsulation frame-relay [Hauwei-serial1/0/0] link-protocol fr
Cisco(config-if)# frame-relay lmi-type ansi [Hauwei-serial1/0/0] fr lmi type ansi
Cisco(config-if)# ip address 2.2.2.1 [Hauwei-serial1/0/0] ip address 2.2.2.1
255.0.0.0 255.0.0.0
Cisco(config-if)# no frame-relay inverse- [Hauwei-serial1/0/0] undo fr inarp
arp [Hauwei-serial1/0/0] fr map ip 2.2.2.2 102
Cisco(config-if)# frame-relay map ip broadcast
2.2.2.2 102 broadcast [Hauwei-serial1/0/0] return
Cisco(config-if)# end <Hauwei> display fr map-info
Cisco# show frame-relay map <Hauwei> display fr lmi-info
Cisco# show frame-relay lmi
Configure Frame-Relay – Dynamic Mapping
Cisco# configure terminal <Hauwei> system-view
Cisco(config)# interface serial 1/0/0 [Hauwei] interface serial 1/0/0
Cisco(config-if)# encapsulation frame-relay [Hauwei-serial1/0/0] link-protocol fr
Cisco(config-if)# frame-relay lmi-type ansi [Hauwei-serial1/0/0] fr lmi type ansi
Cisco(config-if)# ip address 2.2.2.1 [Hauwei-serial1/0/0] ip address 2.2.2.1
255.0.0.0 255.0.0.0
Cisco(config-if)# end [Hauwei-serial1/0/0] return
Cisco# show frame-relay map <Hauwei> display fr map-info
Cisco# show frame-relay lmi <Hauwei> display fr lmi-info
Backup and Restore IOS/VRP OS Using TFTP Server
BACKUP
Cisco# copy flash tftp
Source filename[]? c7200-adventerprisek9-
mz.124-24.T5.bin
Address or name of remote host[]?
BACKUP
192.168.1.1
<Hauwei> tftp 192.168.1.1 put
Destination filename [c7200-
flash:/VR1220-V200R001C01SPC500.CC VRP-
adventerprisek9-mz.124-24.T5.bin]?
OS.cc
RESTORE
RESTORE
Cisco# copy tftp flash
<Hauwei> tftp 192.168.1.1 get VRP-OS.cc
Proceed [confirm]
flash:/AR1220.CC
Address or name of remote
Info: Transter file in binary mode
host[192.168.1.1]? 192.168.1.1
Downloading the file from the remote TFTP
Source filename [c7200-adventerprisek9-
server. Please waiting….
mz.124-24.T5.bin]?
Destination filename [c7200-
adventerprisek9-mz.124-24.T5.bin]? c7200
Accessing tftp://192.168.1.1/ c7200-
adventerprisek9-mz.124-24.T5.bin