Scribd Logo
Upload

Welcome to Scribd!

  • 88 views

    15.6.1 Packet Tracer - Configure IPv4 and IPv6 Static and Default Routes

    Uploaded by

    Hạnh
    The document describes configuring static and default routes for IPv4 and IPv6 on an Edge Router connected to two ISPs. It involves: 1) Configuring a static default route through ISP1 and a floating default route through ISP2 on the Edge Router for IPv4 and IPv6. 2) Configuring static routes from ISP1 to the two internal LANs and floating static routes as backups through ISP2. 3) Configuring host routes from the Edge Router to an important customer server, including a primary route and floating route.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    15.6.1 Packet Tracer - Configure IPv4 and IPv6 Static and Default Routes

    Uploaded by

    Hạnh
    88 views4 pages
    The document describes configuring static and default routes for IPv4 and IPv6 on an Edge Router connected to two ISPs. It involves: 1) Configuring a static default route through ISP1 and a floating default route through ISP2 on the Edge Router for IPv4 and IPv6. 2) Configuring static routes from ISP1 to the two internal LANs and floating static routes as backups through ISP2. 3) Configuring host routes from the Edge Router to an important customer server, including a primary route and floating route.

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document describes configuring static and default routes for IPv4 and IPv6 on an Edge Router connected to two ISPs. It involves: 1) Configuring a static default route through ISP1 and a floating default route through ISP2 on the Edge Router for IPv4 and IPv6. 2) Configuring static routes from ISP1 to the two internal LANs and floating static routes as backups through ISP2. 3) Configuring host routes from the Edge Router to an important customer server, including a primary route and floating route.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    88 views4 pages

    15.6.1 Packet Tracer - Configure IPv4 and IPv6 Static and Default Routes

    Uploaded by

    Hạnh
    The document describes configuring static and default routes for IPv4 and IPv6 on an Edge Router connected to two ISPs. It involves: 1) Configuring a static default route through ISP1 and a floating default route through ISP2 on the Edge Router for IPv4 and IPv6. 2) Configuring static routes from ISP1 to the two internal LANs and floating static routes as backups through ISP2. 3) Configuring host routes from the Edge Router to an important customer server, including a primary route and floating route.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 4
    At a glance
    Powered by AI
    The key takeaways are that static and default routes need to be configured on the Edge Router and ISP routers to provide connectivity between the internal LANs and the internet. Floating static routes are also configured to provide redundancy in case the primary routes fail.

    Static and default routes are configured on the Edge Router to provide internet access to the internal LAN users through the ISPs. The default routes define how to reach networks that are not explicitly defined in the routing table. This allows connectivity to the internet.

    Floating static routes are configured on ISP1 for the internal LANs to provide redundancy. If the primary static routes to the LANs fail or go down, the floating static routes will be used as an alternate path through ISP2 to maintain connectivity.

    Packet Tracer - Configure IPv4 and IPv6 Static and Default Routes

    Addressing Table
    Trần Ngọc Nguyên Hạnh - 5200554

    Device Interface IP Address / Prefix

    Edge_Router S0/0/0 10.10.10.2/30

    Edge_Router S0/0/0
    2001:db8:a:1::2/64

    Edge_Router
    S0/0/1 10.10.10.6/30

     2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 4 www.netacad.com
    Packet Tracer - Configure IPv4 and IPv6 Static and Default Routes

    Device Interface IP Address / Prefix

    Edge_Router S0/0/1
    2001:db8:a:2::2/64

    Edge_Router
    G0/0 192.168.10.17/28

    Edge_Router G0/0
    2001:db8:1:10::1/64

    Edge_Router
    G0/1 192.168.11.33/27

    Edge_Router G0/1
    2001:db8:1:11::1/64
    ISP1 S0/0/0 10.10.10.1/30

    ISP1 S0/0/0
    2001:db8:a:1::1/64

    ISP1
    G0/0 198.0.0.1/24

    ISP1 G0/0
    2001:db8:f:f::1/64
    ISP2 S0/0/1 10.10.10.5/30

    ISP2 S0/0/1
    2001:db8:a:2::1/64

    ISP2
    G0/0 198.0.0.2/24

    ISP2 G0/0
    2001:db8:f:f::2/64
    PC-A NIC 192.168.10.19/28

    PC-A NIC
    2001:db8:1:10::19/64
    PC-B NIC 192.168.11.4/27

    PC-B NIC
    2001:db8:1:11::45
    Customer Server NIC 198.0.0.10

    Customer Server NIC


    2001:db8:f:f::10

    Objectives
    In this Packet Tracer summary activity, you will configure static, default, and floating static routes for both the
    IPv4 and IPv6 protocols.
     Configure IPv4 Static and Floating Static Default Routes.
     Configure IPv6 static and floating static default routes.
     Configure IPv4 static and floating static routes to internal LANs.
     Configure IPv6 static and floating static routes to the internal LANS.
     Configure IPv4 host routes.
     Configure IPv6 host routes.

    Background / Scenario
    In this activity, you will configure IPv4 and IPv6 default static and floating static routes.
    Note: The static routing approach that is used in this lab is used to assess your ability to configure different
    types of static routes only. This approach may not reflect networking best practices.

     2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of 4 www.netacad.com
    Packet Tracer - Configure IPv4 and IPv6 Static and Default Routes

    Instructions
    Part 1: Configure IPv4 Static and Floating Static Default Routes
    Open configuration window

    The PT network requires static routes to provide internet access to the internal LAN users through the ISPs.
    In addition, the ISP routers require static routes to reach the internal LANs. In this part of the activity, you will
    configure an IPv4 static default route and a floating default route to add redundancy to the network.

    Step 1: Configure an IPv4 static default route.


    On Edge_Router, configure a directly connected IPv4 default static route. This primary default route should
    be through router ISP1.

    Step 2: Configure an IPv4 floating static default route.


    On Edge_Router, configure a directly connected IPv4 floating static default route. This default route should
    be through router ISP2. It should have an administrative distance of 5.

    Part 2: Configure IPv6 Static and Floating Static Default Routes


    In this part of the activity, you will configure IPv6 static default and floating static default routes for IPv6.

    Step 1: Configure an IPv6 static default route.


    On Edge_Router, configure a next hop static default route. This primary default route should be through
    router ISP1.

    Step 2: Configure an IPv6 floating static default route.


    On Edge_Router, configure a next hop IPv6 floating static default route. The route should be via router ISP2.
    Use an administrative distance of 5.
    Close configuration window

    Part 3: Configure IPv4 Static and Floating Static Routes to the Internal LANs
    In this part of the lab you will configure static and floating static routers from the ISP routers to the internal
    LANs.

    Step 1: Configure IPv4 static routes to the internal LANs.


    Open configuration window

    a. On ISP1, configure a next hop IPv4 static route to the LAN 1 network through Edge_Router.
    b. On ISP1, configure a next hop IPv4 static route to the LAN 2 network through Edge_Router.

    Step 2: Configure IPv4 floating static routes to the internal LANs.


    a. On ISP1, configure a directly connected floating static route to LAN 1 through the ISP2 router. Use an
    administrative distance of 5.
    b. On ISP1, configure a directly connected floating static route to LAN 2 through the ISP2 router. Use an
    administrative distance of 5.

    Part 4: Configure IPv6 Static and Floating Static Routes to the Internal LANs.

    Step 1: Configure IPv6 static routes to the internal LANs.


    c. On ISP1, configure a next hop IPv6 static route to the LAN 1 network through Edge_Router.
    d. On ISP1, configure a next hop IPv6 static route to the LAN 2 network through Edge_Router.

     2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 3 of 4 www.netacad.com
    Packet Tracer - Configure IPv4 and IPv6 Static and Default Routes

    Step 2: Configure IPv6 floating static routes to the internal LANs.


    a. On ISP1, configure a next hop IPv6 floating static route to LAN 1 through the ISP2 router. Use an
    administrative distance of 5.
    b. On ISP1, configure a next hop IPv6 floating static route to LAN 2 through the ISP2 router. Use an
    administrative distance of 5.
    If your configuration has been completed correctly, you should be able to ping the Web Server from the hosts
    on LAN 1 and LAN 2. In addition, if the primary route link is down, connectivity between the LAN hosts and
    the Web Server should still exist.
    Close configuration window

    Part 5: Configure Host Routes


    Users on the corporate network frequently access a server that is owned by an important customer. In this
    part of the activity, you will configure static host routes to the server. One route will be a floating static route to
    support the redundant ISP connections.

    Step 1: Configure IPv4 host routes.


    Open configuration window

    a. On Edge Router, configure an IPv4 directly connected host route to the customer server.
    b. On Edger Router, configure an IPv4 directly connected floating host route to the customer sever. Use an
    administrative distance of 5.

    Step 2: Configure IPv6 host routes.


    a. On Edge Router, configure an IPv6 next hop host route to the customer server through the ISP1 router.
    b. On Edger Router, configure an IPv6 directly connected floating host route to the customer sever through
    the ISP2 router. Use an administrative distance of 5.
    Close configuration window
    End of document

     2013 - 2019 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 4 of 4 www.netacad.com

    You might also like