INJECTION PUMP SPECIFICATION ©

FULL LOAD RPM: 1500 CUSTOMER PART #: 2643U617 BL MODEL NO.: DB2635-5206
GOV. REGULATION: 3-5 % CUSTOMER'S NAME: SUPERSEDES:
ENGINE: T 6.60 PERKINS ENGINES LIMITED EDITION NO.: 5
APPLICATION: GENERATOR DATED: 07-31-03

NOTE: THIS SPECIFICATION DEVELOPED WITH ISO LONG INLET STUD.

ALL SPEEDS ARE IN ENGINE RPM UNLESS OTHERWISE NOTED.
USE LATEST REVISION FOR ALL REFERENCED DOCUMENTS.
TEST STAND: PUMP SETTINGS: FOLLOWING PUMP SERVICE
1. CALIBRATING HIGH PRESSURE PIPES...SAE J1418/ISO 4093: 1. ROLLER-TO-ROLLER DIMENSION: 1.979" ± .001"
.063" (1.6 mm) I.D. X 25" (635 mm) LONG. (50.27 ± .025 mm)
2. CALIBRATING INJECTORS... S.A.E. J968/ISO 7440: MAXIMUM ECCENTRICITY: .004" (0.10 mm) T.I.R.
0.5 mm ORIFICE PLATE NOP: 3000 PSI (207 bar) LONG. 2. GOVERNOR LINKAGE GAP: .125"-.145" (3.2-3.7 mm)
3. CALIBRATING FLUID...SAE J967/ISO 4113 (REF. S.B. 201): (USE KIT #23093 S.B. 95)
a. TEMPERATURE AT INLET: 100°-108°F (38°-42°C) 3. SPEED DROOP SETTING: ASSEMBLE SPEED DROOP PER S.B. 97R.
b. SUPPLY PRESSURE (S.B. 334): 5.0 ± 0.5 PSI (34 ± 3 kPa) AT PUMP ENSURE CONTROL SPRING IS INSTALLED WITH 3.5 ± ½ TURN ON
INLET. CONTROL SPRING GUIDE.
4. 1000 RPM (WOT): OPERATE PUMP FOR 10 MINUTES TO BRING TO
PUMP INSTALLATION: OPERATING TEMPERATURE AND CLEAR AIR FROM SYSTEM.
ROTATION-C-* 5. 400 RPM (WOT):
NAME PLATE-L-SIDE** a. CHECK ESO SHUT-OFF: 4 mm³/STROKE, MAX.
#1 CYL.-9-O'CLOCK** b. CHECK FOR MINIMUM TRANSFER PUMP LIFT OF 18" HG.
THROTTLE-L-SIDE** (60 kPa).
E.S.O. (24V E.T.R.) 6. 1500 RPM (WOT):
a. SET TRANSFER PUMP PRESSURE FOR 70-75 PSI,
* VIEWED FROM DRIVE END ** VIEWED FROM TRANSFER PUMP END (483-517 kPa)(SUPPLY SET PER TEST STAND NOTE 3B).
b. ADJUST RETURN OIL TO 225-475 CC/MIN. RECHECK TRANSFER
PUMP OPERATING SPEED...HALF...ENGINE SPEED PUMP PRESSURE.
AIR TIMED TO HOUSING FLANGE (S.B. 177)(SEE SPECIAL NOTES) c. CHECK HOUSING PRESSURE FOR 4-10.5 PSI,(28-72 kPa).
7. 1500 RPM (WOT): SET ROLLER-TO-ROLLER FUEL DELIVERY: 96.5-
PUMP CALIBRATION CHECKS: AS RECEIVED FOR SERVICE 97.5 mm³/STROKE.
(REF. SL-222)(REF. S.B. 97R FOR SPEED DROOP) 8. 1625 RPM (WOT): ADJUST HIGH IDLE SCREW TO OBTAIN
1. 1000 RPM (WOT): OPERATE PUMP FOR 10 MINUTES TO BRING TO 4 MAX. mm³/STROKE.
OPERATING TEMPERATURE AND CLEAR AIR FROM SYSTEM. 9. TURN LI SCREW IN UNTIL THE SCREW JUST CONTACTS THE
2. TURN SPEED DROOP TO MINIMUM POSITION (C'C DIRECTION). THROTTLE BOSS WITH THE THROTTLE IN THE WOT POSITION.
3. 1625 RPM (WOT): RESET HIGH IDLE SCREW TO OBTAIN LOCK LI SCREW NUT.
4 MAX. mm³/STROKE. 10. CHECK POINTS:
4. CHECK POINTS: (SEQUENCE MUST BE FOLLOWED AS LISTED)
THROTTLE T.P.
THROTTLE RPM POSITION mm³/STROKE PRESSURE
RPM POSITION mm³/STROKE a. 1625 WOT 4 MAX. ---
a. 1625 WOT 4 MAX. b. 1500 WOT* 4 MAX. ---
b. 1500 WOT* 4 MAX. c. 1500 WOT 96.5-97.5 70-75***
c. 1500 WOT 95.5-98.5 d. 400 WOT* 4 MAX. ---
d. 400 WOT* 4 MAX. e. 200 WOT 55 MIN. 10 MIN.**
e. 200 WOT 50 MIN.
* E.S.O. DE-ENERGIZED ** (69 kPa) *** (483-517 kPa)
* E.S.O. DE-ENERGIZED
11. SPECIAL NOTES:
a. TORQUE ALL FASTENERS PER S.B. 106.
b. TURN SPEED DROOP ADJUSTING CAP 1 ± 1/4 TURN FROM FULL
COUNTERCLOCKWISE POSITION.
c. SEAL FASTENERS PER S.B. 134R AND 365R1.
d. CHECK PUMP FOR MODIFICATION NAME PLATES PER S.B. 490.
e. AIR TIME PUMP USING HARTRIDGE BASIC AIR TIMING TOOL
7244-27 WITH INSERT 7244-30 AND PILOT RING 7244-26E
CONNECT AIR SUPPLY WITH 60-100 PSI (4.1-6.9 BAR) TO #1
CYLINDER OUTLET. SET TOOL TO 336° AND INSTALL TO DRIVE
SHAFT. SLOWLY ROTATE TOOL CLOCKWISE UNTIL ROLLERS
STRIKE CAM RING AND TOOL STOPS, SCRIBE LINE ON
HOUSING FLANGE. REPEAT PROCEDURE TO ENSURE
ACCURACY. IF INTERFERENCE BETWEEN STRAIGHT EDGE
AND HOUSING FLANGE OCCURS, PLACE WASHER (i.e. 13521)
BETWEEN STRAIGHT EDGE AND TOOL.

© STANADYNE Corporation, all rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any
form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
DB2635-5206 EDITION 5 DATED 07/31/2003 PAGE 2 OF 4
DESCRIPTION QTY P/N HOUSING & DRIVE GROUP P/N QTY DESCRIPTION
(61387)

SEAL, DRIVESHAFT 2 10453

21660 1 SCREW ASSY, VENT
OR 21661-21665
DRIVESHAFT 1 30941
11331 2 SCREW, HEX HEAD
22601 1 SCREW, BUTTON HD CAP
27606 1 WASHER, SEALING
12259 1 SCREW, PAN HEAD
KEY, WOODRUFF 1 30387 10464 1 WASHER, SEALING
SEAL, O-RING 1 16371 26180 1 BEARING, THRUST
HOUSING ASSY, PUMP 1 32424 21522 2 WASHER, DRSFT SPRING
SLEEVE, THROTTLE STOP 1 24364

SCREW, RIVET 2 24419 10443 1 RING, RETAINING

21521 1 WASHER, THRUST
NAMEPLATE 1 28771
11354 1 WASHER, PLAIN
GASKET, TIMING WINDOW CVR 1 27603
27602 1 SEAL, O-RING
SCREW, HEX HEAD 2 21194 11363 1 SCREW, SCKT HEAD CAP
COVER, TIMING WINDOW 1 23107 10393 1 SCREW, SOCKET HD CAP

NOTES:

DESCRIPTION QTY P/N HEAD & ROTOR GROUP P/N QTY DESCRIPTION
(60202)
30266 1 H&R ASSY, HYD 6 CYL
11086 2 PLUNGER, ROTOR
ROLLER, CAM 2 11141 USE 11087-11090 (STD)
OR 11097-11100 (O/S)
SHOE, CAM ROLLER 2 20116 AS IND. ON ROTOR SB 60R
11438 1 SCREW, SET
12216 1 SCREW, HEAD PLUG
RING, CAM 1 21686 20727 6 CONNECTOR, FUEL LINE

29710 1 SCREW, SKT HEAD CAP

29384 1 PLATE, SINTERED LOCK

SEAL, O-RING 1 27245 27601 1 SEAL, O-RING
13827 1 VALVE, DELIVERY
SPRING, LEAF 1 11197 OR 13828 (O/S) AS REQ'D
REF. S.B. 143B
SCREW, LEAF SPR ADJ 1 11175 13837 1 SCREW, DLVY VALVE RET

SPRING, DLVY VALVE 1 16441

STOP, DELIVERY VALVE 1 16440

NOTES:

DESCRIPTION QTY P/N TRANSFER PUMP GROUP P/N QTY DESCRIPTION

(60023)
20530 2 RETAINER, ROTOR
SEAL, TRANSFER PUMP 1 27608
21232 1 LINER, TRANSFER PUMP
20511 4 BLADE, TRANSFER PUMP
OR 20512 REF. S.B. 304
20528 1 RING, ROTOR RETAINER
28987 1 REGULATOR ASSY, TP
SPRING, TP BLADE 2 15699
ROLL PIN 1 19837
SEAL, TP RGLTR SLEEVE 1 19844

19855 1 SPRING, REGULATING

PISTON, REGULATING 1 19895

PLUG ASSY, END PL ADJ 1 15228

FILTER, INLET 1 28986 33128 1 CAP, TP END

NOTES:

INDENTED ITEMS INCLUDED

DB2635-5206 EDITION 5 DATED 07/31/2003 PAGE 3 OF 4
DESCRIPTION QTY P/N GOVERNOR GROUP P/N QTY DESCRIPTION
(63252)
SPRING, SPEED DROOP 1 15617 20240 1 ROD ASSY-CONTROL
BROWN W/RED STRIPE
ARM ASSY, GOVERNOR 1 24929 13554 1 PIN, CONTROL SPRING

SHAFT, GOVERNOR ARM 1 12214 27606 1 WASHER, SEALING

SEAL, O-RING 2 31332 12966 1 SEAL, O-RING

NUT, PIVOT SFT RTNR 2 12288 36556 1 CAP, ADJUSTING

SPRING, DAMPER 1 20475 20355 1 CAP, DROOP CTRL LOCK

PISTON ASSY, DAMPER 1 16572

27599 1 GUIDE, CONTROL ROD
18121 1 BARREL ASSY, DAMPER
22134 1 ARM ASSY, MTR VALVE
SLEEVE, GOV THRUST 1 14483 11563 1 VALVE, METERING
* SEE NOTE
26427 1 SHIM, MTR VALVE SPRG
20359 1 SPRING, MTR VALVE
WEIGHT, GOVERNOR 6 11658
29111 1 RETAINER ASSY, GOV WT
WASHER, THRUST 1 20222
RING, RETAINING 1 12285

NOTES: * O.S. METERING VALVE AND ARM ASSEMBLY 22248 REFERENCE S.B.336

DESCRIPTION QTY P/N LINKAGE GROUP P/N QTY DESCRIPTION

(60030)

SPACER, GOV SPRING 1 15306

SEAL, O-RING 2 17438 16279 1 SHAFT, SHUTOFF

WASHER, SPACER 2 14408 12253 1 CLIP, SHAFT RETAINER

12221 1 LEVER, THROTTLE FORK
SHAFT ASSY, THROTTLE 1 29366
NUT, HEX 1 12174 12169 1 SCREW, HEX HEAD
SCREW, HEX HEAD 1 12972 12174 1 NUT, HEX

17605 1 HOOK ASSY, GOV LKGE

12360 1 SCREW, HEX HEAD
12362 1 LOCK WASHER, SHPRF
17604 1 HOOK, GOV LINKAGE

12358 1 LINK ASSY, ADJUSTING

11919 1 SPRING, GOVERNOR LINK

NOTES:

DESCRIPTION QTY P/N COVER GROUP P/N QTY DESCRIPTION

(60826)

26564 1 RGLTR ASSY, HSG PRESS

27607 1 SEAL, O-RING
14760 2 NUT, HEX LOCK
28388 2 TERMINAL, ESO
SCREW, BUTTON HD CAP 3 22351 12049 2 WASHER, INTL TOOTH
12500 2 WASHER, FIBER

NUT, HEX 2 12519 30789 1 CAP, COVER SCREW

WASHER, PLAIN 2 18501

30788 1 CUP, COVER SCREW

SEAL, RECT SECTION 1 27244 21898 1 COVER, GOV CONTROL

26387 1 SOLENOID, 24V ETR

2-23190 TUBE, INSULATE

NOTES: E.S.O. TERMINAL ORIENTATION TO BE IN LINE WITH SIDES OF COVER

INDENTED ITEMS INCLUDED

DB2635-5206 EDITION 5 DATED 07/31/2003 PAGE 4 OF 4

FOR SERVICE USE ONLY FOR ENGINEERING USE ONLY

APPLICABLE SERVICE ASSEMBLIES DATE CHANGE NO. EDITION
THROTTLE SHAFT BUSHING REPLACEMENT 17776 04/19/1995 23815 1
PILOT TUBE REPLACEMENT (REF SB 171C) 32980 07/07/1998 25738 2
OVERHAUL GASKET KIT 33814 01/05/1999 25738 3
ESO MOUNTING AND GROUNDING KIT 26431 02/07/2000 26664 4
07/31/2003 27563 5

INDENTED ITEMS INCLUDED