0% found this document useful (0 votes)
302 views5 pages

Calibracion RPM 311c

Uploaded by

Joan Cardona
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
302 views5 pages

Calibracion RPM 311c

Uploaded by

Joan Cardona
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Shutdown SIS

Previous Screen

Product:  EXCAVATOR 
Model:  311C EXCAVATOR CKE 
Configuration: 311C U Excavator CKE00001-UP (MACHINE) POWERED BY 3064 Engine 

Testing and Adjusting


311C and 314C Excavators Electric and Electronic
Media Number -RENR5557-04 Publication Date -01/05/2007 Date Updated -29/05/2007

i01673957

Calibration Mode - Enter


SMCS - 1931

The following procedure is for the 311C.

Illustration 1 g00795313

(1) Backup switch

1. Move backup switch (1) to the AUTO position.


Illustration 2 g00795319

(2) Switch for one touch low idle

(3) Engine speed dial

(4) Starter switch

2. Ensure that engine speed dial (3) is at the LOW IDLE position (tortoise).

3. Depress the switch for one touch low idle (2).

4. Start the engine.

5. Move the engine speed dial (3) to the HIGH IDLE position (Rabbit).

Illustration 3 g00795325

Monitor

(5) Low idle indicator

6. Release the switch for one touch low idle (2) after low idle indicator (5) illuminates.
7. Depress the switch for one touch low idle (2) for one second. The low idle indicator (5) will blink
slowly.

8. Release the switch for one touch low idle (2) .

9. Move the engine speed dial indicator to the position of the desired function.

Table 1 lists the functions of the positions of the engine speed dial.

Table 1
Engine Speed Dial
Function
Indicator
1 The proportional reducing valve is calibrated.
The lower calibration pressure for the proportional reducing valve is
3
displayed.
The higher calibration pressure for the proportional reducing valve is
4
displayed.
10 The governor actuator is calibrated.

Calibration Mode is automatically cancelled when the engine has been turned OFF for 30 seconds.

The following procedure is for the 314CCR.

Illustration 4 g00864731

Seat support

(1) Backup switch


1. Place backup switch (1) in AUTO position.

Illustration 5 g00864760

Right Console

(2) Engine speed dial

(3) One touch low idle switch

(4) Starter switch

1. Make sure that the engine speed dial (2) is in position 1.

2. Depress the one touch low idle switch (3).

3. Place the starter switch (4 ) in the ON position.

4. Place the engine speed dial (2) in position 10.


Illustration 6 g00864781

Monitor

(5) One touch low idle indicator

1. After the one touch low idle indicator (5) comes on, release the one touch low idle switch (3). If the
governor actuator shifts to the initial position, the start of the calibration mode is complete.

The following functions are assigned to each position of the engine speed dial in calibration mode.

Table 2
Engine Speed Dial Indicator
Function

1 The proportional reducing valve is calibrated.


The lower calibration data for the proportional reducing valve is
3
displayed.
The higher calibration data for the proportional reducing valve is
4
displayed.
10 The governor actuator is calibrated.

Use the following procedure in order to cancel the calibration mode.

1. When you terminate the calibration mode, place the starter switch (4) in the OFF position. The
calibration mode will be cancelled after approximately 30 seconds.

Copyright 1993 - 2021 Caterpillar Inc. Wed Sep 15 23:20:54 EST 2021 
All Rights Reserved.
Private Network For SIS Licensees.

You might also like