HCW L Housing

W
Lower Internal Neoprene
Restraining Acoustical Pad
Nut
MASON INDUSTRIES, Inc.
Manufacturers of Vibration Control Products
350 Rabro Drive 2101 W. Crescent Ave., Suite D height
1” 25mm and 2” 50mm
Non-Skid Pad is used in Non-Seismic zones only.
DEFLECTION
Remove pad prior to bolting. Reduce published
by 1/8" if pad is removed.
RESTRAINED SEISMIC
SLRSO &
Hauppauge, NY 11788
631/348-0282
FAX 631/348-0279
[email protected]
Anaheim, CA 92801
714/535-2727
FAX 714/535-5738
[email protected]
SPRING MOUNTS with
and without EXTENDED
BASEPLATES
SLRSOEBP
www.Mason-Ind.com www.MasonAnaheim.com DATA SHEET DS-224-3

OSHPD OPA-194 All mounts except SLRS-9 are

SLRSO Rated Load Curves (lbs kg)
awaiting OSHPD-194 approval.
SLRS-9 has not been submitted.
1” 25mm Deflection B, 1 - 9 Springs 14830
6727
Horizontal, Vertical and 45° plotted

xi s
SL
Ratings are California OSHPD

°A
RS

45
O-
14637 6 submitted values having the OSHPD
Vertical Limit "D" Tap– 4 Holes. Load Ratings are based V 6653

SL
Anchorage Preapproval Number
on bolting to two opposed holes.

RS
E 13430
Stops– Out of OPA-0194. Testing and calculations

O-
R 7618 6091

4
contact during E T 3463
7500 were performed to meet
I 10500
normal operation E C
SL 3409 4773 OSHPD criteria.
E A
RS
O

SL
E L
-2 To use OSHPD submitted rated

RS
6507
2958 load curves:

O-
4400
Adjustment 2000 4400

1
Bolt 2000 1) Calculate Vertical and Horizontal
2409 Forces on mountings including
SLRSO-B 1092 translations and overturning moments.
1401 4800 6007 11754 14000 2) Plot Horizontal and Vertical Loads.
MBD– 637 2182 2730 5343 6350 The intersection must fall within the
Max Bolt HORIZONTAL area below the OSHPD curve.
Rubber Diameter
H Snubbing TYPE SLRSO and SLRS RATINGS 1” 25mm Deflection Series
Collar
Rated Rated Mount Max. Horiz.
T SLRSO Capacity Defl Constant Housing Spring
Size (Ibs) (kg) (in) (mm) (Ibs/in)(kg/mm) G Rating† Color
HCL B-65 65 29 2.10 53 31 0.55 21.6 Brown
Steel B-85 85 39 2.10 53 40 0.74 16.5 Wht/Blk
HCW L Housing B-115 115 52 2.00 51 57 1.02 12.2 Silver
W B-150 150 68 2.00 51 75 1.33 9.3 Orange
Lower B-280 280 127 1.60 41 174 3.10 5.0 Green
Internal Neoprene B-450 450 204 1.31 33 344 6.18 3.1 Red
Restraining Acoustical Pad
Nut B-750 750 340 1.12 28 670 12.1 1.9 White
B-1000 1000 454 1.00 25 1000 18.2 1.4 Blue
Non-Skid Pad is used in Non-Seismic zones only.
Remove pad prior to bolting. Reduce published 1-1000 1000 454 1.00 25 1000 18.2 4.8 Black
height by 1/8" if pad is removed. 1-1350 1350 612 1.00 25 1350 24.5 3.6 Yellow
1-1750 1750 794 1.00 25 1750 31.8 2.7 Black*
Illustration above shows a SLRSO-4 housing with four C springs. 1-2100 2100 953 1.00 25 2100 38.1 2.3 Yellow
1-2385 2385 1082 1.00 25 2385 43.3 2.0 Yellow**
1-2650 2650 1202 1.00 25 2650 48.1 1.8 Red*
1-2935 2935 1331 1.00 25 2935 53.2 1.6 Red**
2-3500 3500 1588 1.00 25 3500 63.5 1.7 Black*
2-4200 4200 1905 1.00 25 4200 76.2 1.4 Yellow*
2-4770 4770 2164 1.00 25 4770 86.6 1.3 Yellow**
4-5400 5400 2449 1.00 25 5400 98.0 2.2 Yellow
4-7000 7000 3175 1.00 25 7000 127.0 1.7 Black*
4-8400 8400 3810 1.00 25 8400 152.4 1.4 Yellow*
4-9540 9540 4327 1.00 25 9540 173.1 1.2 Yellow**
14830
6727 4-10600 10600 4808 1.00 25 10600 192.3 1.1 Red*
4-11740 11740 5325 1.00 25 11740 213.0 1.0 Red**
xi s

SL SLRS-9
°A

RS 6-12600 12600 5715 1.00 25 12600 228.6 1.1 Yellow*

45

14637 O-
6653
6 6-14310 14310 6491 1.00 25 14310 259.6 1.0 Yellow**
V
SL

6-15900 15900 7212 1.00 25 15900 288.5 0.9 Red*

RS

E 13430
SLRS-9 has nine
R C springs and has6091closed sides. Not shown 6-17610 17610 7988 1.00 25 17610 319.5 0.8 Red**
O-

7618
4

are SLRSO-B, which has one B spring and SLRSO-1, SLRSO-2

T 3463 SLRS Size
I have 7500 10500 six C springs respectively.
& SLRSO-6 which S one,
3409 two and
4773
C LR 9-18900 18900 8573 1.00 25 18900 342.9 ‡l Yellow*
SO
All springs have Aan additional travel to solid equal to 50% of the 9-21465 21465 9736 1.00 25 21465 389.4 ‡l Yellow**
SL

-2
rated deflection. L
RS

6507 9-23850 23850 10818 1.00 25 23850 432.7 ‡l Red*

2958
O-

4400
2000
mounts4400
1

Designs using these to resist wind loads must be in

2000 *with Red inner spring ‡SLRS-9 under test
accordance with ASCE 7-05. **with Green inner spring
2409
1092
TYPE SLRSO and SLRS SLRSO-B
DIMENSIONS (inches and mm) †
Housing load ratings expressed in G’s are based on tests with
1401 4800 6007 11754 14000
Type & Size H T637 D
2182 E
2730 5343L 6350HCL W HCW MBD bolted connections to steel top and bottom. SLRSO & SLRS
SLRSO- 83/4 3/8 1HORIZONTAL
/2 11/8 81/2 7 41/4 23/4 5/8 housings require uniform support under entire base plate.
B 222 10 13 29 216 178 108 70 16
SLRSO- 83/4 3/8 5/8 13/8 91/2 71/2 51/4 31/2 5/8 SPRING CHARACTERISTICS (inches and mm)
1 222 10 16 35 241 191 133 89 16 Spring Free Ratio Ratio
SLRSO- 83/4 3/8 5/8 13/8 14 121/4 51/4 31/2 5/8 Size OD Height Kx/Ky OD/OH
2 222 10 16 35 356 311 133 89 16
B 23/8 60 40/0 102 0.70-0.80 0.80
SLRSO- 83/4 3/8 7/8 13/8 133/4 11 8 61/4 3/4
C 27/8 73 41/8 105 0.90-1.10 0.92
4 222 10 22 35 350 279 203 159 19
SLRSO- 93/4 3/8 1 15/8 19 157/8 9 6 1 All springs have an additional travel to solid
6 248 10 25 41 483 403 229 152 25 equal to 50% of the rated deflection.
SLRS- 93/4 5/8 1 2 18 153/4 13 103/4 1
9 248 16 25 51 457 400 330 273 25 Solid Spring Height = Free Height minus 1.5
times the Rated Deflection.
 Non-Skid Pad is used in Non-Seismic zones only.
Remove pad prior to bolting. Reduce published
height by 1/8" if pad is removed.

SLRSO & SLRSOEBP MASON INDUSTRIES

All mounts except SLRSEBP-9 are

SLRSOEBP (Extended Base Plate) OSHPD OPA-194
Rated Load Curves (lbs kg)
awaiting OSHPD-194 approval.
SLRSEBP-9 has not been submitted.
1” 25mm Deflection B, 1 - 9 Springs 14830 Horizontal, Vertical and 45° plotted
6727
"D" Tap– 4 Holes. Load Ratings are based Ratings are California OSHPD

xi s
SL
submitted values having the OSHPD

°A
on bolting to two opposed holes. RS

45
O-
Vertical Limit E
14637
6653
6 Anchorage Preapproval Number
V
Stops– Out of

SL
OPA-0194. Testing and calculations
E

RS
E
E
13430
contact during were performed to meet

O-
R 7618 6091

4
normal operation E T 3463
I 7500 10500
OSHPD criteria.
SL 3409 4773
C RS To use OSHPD submitted rated
A O

SL
Rubber L
-2 load curves:

RS
H
6507
Snubbing Adjustment 2958 1) Calculate Vertical and Horizontal

O-
4400
2000 4400

1
Collar Bolt 2000 Forces on mountings including
2409
translations and overturning
SLRSO-B 1092 moments.
MBD– T 1401 4800 6007 11754 14000 2) Plot Horizontal and Vertical Loads.
Max Bolt 637 2182
HORIZONTAL
2730 5343 6350 The intersection must fall within the
Diameter area below the OSHPD curve.

HCL TYPE SLRSOEBP and SLRSEBP RATINGS 1” 25mm Deflection Series

L Rated Rated Mount Max. Horiz.
SLRSOEBP Capacity Defl Constant G Rating Bolted Spring
HCW HCL Size (Ibs) (kg) (in) (mm) (Ibs/in)(kg/mm) to Concrete† Color
W B-65 65 29 2.10 53 31 0.55 21.6 Brown
Lower
Restraining B-85 85 39 2.10 53 40 0.74 16.5 Wht/Blk
Nut B-115 115 52 2.00 51 57 1.02 12.2 Silver
Steel Internal B-150 150 68 2.00 51 75 1.33 9.3 Orange
Housing Neoprene B-280 280 127 1.60 41 174 3.10 5.0 Green
Acoustical B-450 450 204 1.31 33 344 6.18 3.1 Red
Illustration above shows Pad B-750 750 340 1.12 28 670 12.1 1.9 White
a SLRSOEBP-4 housing B-1000 1000 454 1.00 25 1000 18.2 1.4 Blue
with four C springs. 1-1000 1000 454 1.00 25 1000 18.2 4.4 Black
1-1350 1350 612 1.00 25 1350 24.5 3.3 Yellow
1-1750 1750 794 1.00 25 1750 31.8 2.5 Black*
1-2100 2100 953 1.00 25 2100 38.1 2.1 Yellow
HCL 1-2385 2385 1082 1.00 25 2385 43.3 1.9 Yellow**
1-2650 2650 1202 1.00 25 2650 48.1 1.7 Red*
1-2935 2935 1331 1.00 25 2935 53.2 1.5 Red**
SLRSOEBP-B 2-3500 3500 1588 1.00 25 3500 63.5 1.7 Black*
2-4200 4200 1905 1.00 25 4200 76.2 1.4 Yellow*
2-4770 4770 2164 1.00 25 4770 86.6 1.3 Yellow**
14830
4-5400 5400 2449 1.00 25 5400 98.0 1.7 Yellow
(6727) HCL 4-7000 7000 3175 1.00 25 7000 127.0 1.3 Black*
4-8400 8400 3810 1.00 25 8400 152.4 1.1 Yellow*
xi s

SL
°A

RS 4-9540 9540 4327 1.00 25 9540 173.1 1.0 Yellow**

45

14637 O-
6 4-10600 10600 4808 1.00 25 10600 192.3 0.9 Red*
(6653)
SLRSOEBP-2
SL

V 4-11740 11740 5325 1.00 25 11740 213.0 0.8 Red**

RS

E 13430
6-12600 12600 5715 1.00 25 12600 228.6 0.8 Yellow*
O-

(6091)
R 7618
4

T (3463) 7500 10500

6-14310 14310 6491 1.00 25 14310 259.6 0.7 Yellow**
I SL (3409) (4773) 6-15900 15900 7212 1.00 25 15900 288.5 0.65 Red*
C RS
O HCL 6-17610 17610 7988 1.00 25 17610 319.5 0.6 Red**
SL

A -2
SLRSEBP Size
RS

6507
L (2958)
O-

4400
(2000) 4400 9-18900 18900 8573 1.00 25 18900 342.9 ‡l Yellow*
1

(2000) HCL 9-21465 21465 9736 1.00 25 21465 389.4 ‡l Yellow**

SLRSEBP-9
2409 9-23850 23850 10818 1.00 25 23850 432.7 ‡l Red*
SLRSO-B (1092)
SLRSOEBP-B has one B spring, SLRSOEBP-2 has two C *with Red inner spring **with Green inner spring ‡SLRSEBP-9 under test
1401 SLRSEBP-9
springs and 4800 6007 11754nine
has 14000springs and has closed
(637) (2182) (2730) (5343) (6350)
sides. Not shownHORIZONTAL
are SLRSOEBP-1, which has one C spring †
Horizontal load ratings expressed in G’s are based on calculations
and SLRSOEBP-6, which has six C springs. with bolted connections to steel on top and concrete inserts on bottom.
SLRSOEBP housings require uniform support under entire base plate.
TYPE SLRSOEBP and SLRSEBP DIMENSIONS (inches and mm)
Type & Size H T D E L HCL W HCW MBD SPRING CHARACTERISTICS (inches and mm)
SLRSOEBP- 9 3/8 1/2 11/8 13 101/2 5 – 5/8 Spring Free Ratio Ratio
B 229 10 13 29 330 267 127 – 16 Size OD Height Kx/Ky OD/OH
SLRSOEBP- 9 3/8 5/8 13/8 10 8 10 8 5/8 B 23/8 60 40/0 102 0.70-0.80 0.80
1 229 10 16 35 254 203 254 203 16 C 27/8 73 41/8 105 0.90-1.10 0.92
SLRSOEBP- 9 3/8 5/8 13/8 141/2 11 12 9 3/4
2 229 10 16 35 368 280 305 229 19 All springs have an additional travel to solid
SLRSOEBP- 9 3/8 7/8 13/8 19 8 14 11 3/4 equal to 50% of the rated deflection.
4 229 10 22 35 482 203 356 280 19 Solid Spring Height = Free Height minus 1.5
SLRSOEBP- 101/4 1/2 1 15/8 27 12 15 12 1 times the Rated Deflection.
6 260 13 25 41 686 305 381 305 25
SLRSEBP- 101/4 5/8 1 2 27 12 19 16 1 Designs using these mounts to resist wind
9 260 16 25 51 686 305 483 406 25 loads must be in accordance with ASCE 7-05.

2
 MASON INDUSTRIES SLRSO & SLRSOEBP
SLRSO TYPE SLRSO and SLRS RATINGS 2” 50mm Deflection Series
Rated Rated Mount Max. Horiz.
2” 50mm Deflection B, B2, B3, 2-C2, 4-C2, SLRSO Capacity Defl Constant Housing Spring
Size (Ibs) (kg) (in) (mm) (Ibs/in)(kg/mm) G Rating† Color
6-C2 & 9-C2 Springs
B-20 20 9 2.40 61 8 0.15 70.0 Tan
"D" Tap– 4 Holes. Load Ratings are based B-26 26 12 2.18 55 12 0.22 53.9 Wht/Blue
on bolting to two opposed holes B-35 35 16 2.20 56 16 0.29 40.0 Purple
E B-50 50 23 2.20 56 24 0.41 28.0 Wht/Red
Vertical Limit E E B-65 65 29 2.10 53 31 0.55 21.6 Brown
Stops– Out of B-85 85 39 2.10 53 40 0.74 16.5 Wht/Blk
contact during E B-115 115 52 2.00 51 57 1.02 12.2 Silver
normal operation B-150 150 68 2.00 51 75 1.33 9.3 Orange
B2-210 210 95 2.12 54 99 1.76 6.8 Silver
Rubber H B2-290 290 132 2.00 51 144 2.59 4.9 Blue
Snubbing "D" Tap– 4 Holes. Load Ratings are based
B2-450 ††
450 204 2.00 51 224 4.00 3.2 Tan
Vertical Limit
Collar on bolting to two opposed holes. B2-680 ††
680 308 2.00 51 340 6.04 2.1 Gray
Stops– Out of
contact during E C2-125 125 57 2.50 64 50 0.89 38.4 Purple
normal operation T C2-170 170 77 2.40 61 70 1.26 28.2 Brown
MBD– E E
Max Bolt C2-210 210 95 2.30 58 90 1.64 22.8 Red
Diameter E C2-260 260 118 2.20 56 120 2.11 18.5 White
Adjustment C2-330 330 150 2.00 51 165 2.94 14.5 Black
Bolt C2-460 460 209 2.00 51 230 4.10 10.4 Blue
C2-610 610 277 2.00 51 305 5.43 7.9 Green
C2-880 ††
880 399 2.00 51 440 7.82 5.5 Gray
MBD– HCL Adjustment C2-1210 ††
1210 549 2.00 51 605 10.8 4.0 Silver
Max Bolt Bolt 1540 699 2.00 51 770 13.7 3.1 Gray*
HCW Diameter L
C2-1540 ††

Rubber C2-1870†† 1870 848 2.00 51 935 16.6 2.6 Silver*

Snubbing W
H 2-C2-340 340 154 2.40 61 140 2.52 17.7 Brown
Collar Non-Skid Pad is used in
Non-Seismic Zones only. 2-C2-420 420 191 2.30 58 180 3.29 14.3 Red
T Remove pad prior to bolting. 2-C2-520 520 236 2.20 56 240 4.21 11.6 White
Lower Steel Internal 2-C2-660 660 299 2.00 51 330 5.86 9.1 Black
Reduce published height by
Restraining Housing HCLNeoprene 1/8" if pad is removed. 2-C2-920 920 417 2.00 51 460 8.18 6.5 Blue
Nut Acoustical
Steel
HCW L Pad Housing 2-C2-1220 1220 553 2.00 51 610 10.8 4.9 Green
W
2-C2-1760†† 1760 798 2.00 51 880 15.7 3.4 Gray
Lower 2-C2-2420 ††
2420 1098 2.00 51 1210 21.5 2.5 Silver
Illustration above shows a SLRSO-4-C2
Internal Neoprene 2-C2-3080†† 3080 1397 2.00 51 1540 27.4 1.9 Gray*
Restraining housing with four C springs. SLRS-9-C2
Nut
Acoustical Pad 2-C2-3740 ††
3740 1696 2.00 51 1870 33.2 1.6 Silver*
has nine C2 springs and has closed
sides.
Non-Skid Pad Notis used shown are SLRSO-B,
in Non-Seismic which
zones only.
4-C2-4840 ††
4840 2195 2.00 51 2420 43.0 2.4 Silver
Remove haspad onepriorB to spring;
bolting.SLRSO-B2,
Reduce publishedwhich has 4-C2-6160 ††
6160 2794 2.00 51 3080 54.8 1.9 Gray*
height one
by 1/8"B2if spring;
pad is removed.
SLRSO-C2, SLRSO-2-C2 4-C2 7480 ††
7480 3393 2.00 51 3740 66.5 1.6 Silver*
& SLRSO-6-C2, which have one, two and 6-C2-7260†† 7260 3293 2.00 51 3630 64.6 1.9 Silver
six C springs respectively. 6-C2-9240†† 9240 4191 2.00 51 4620 82.2 1.5 Gray*
6-C2-11220 11220 5089 2.00 51 5610 99.8
††
1.3 Silver*
Designs using these mounts to resist SLRS Size
wind loads must be in accordance with
ASCE 7-05. 9-C2-13860†† 13860 6287 2.00 51 6930 123.2 ‡ Gray*
SLRSO-9-C2 9-C2-16830†† 16830 7634 2.00 51 8415 149.7 ‡ Silver*

All mounts except SLRS-9-C2 are

*with Red inner spring ‡SLRS-9 under test
OSHPD OPA-194
Rated Load Curves (lbs kg) awaiting OSHPD-194 approval.
SLRS-9-C2 has not been submitted. †
Housing load ratings expressed in G’s are based on tests with bolted
14830
6727 14830 Horizontal, Vertical and connections to steel top and bottom. SLRSO & SLRS housings
(6727) require uniform support under entire base plate.
xi s

SL 45° plotted Ratings are California

°A

RS S
xis

O- LR
45

OSHPD submitted values having the

°A

14637 6 S
V 6653 14637 O- OSHPD Anchorage Preapproval
45
SL

6
††
Published ratings allow minimum 25% additional travel to solid.
(6653)
RS

E 13430
Number OPA-0194. Testing and
SL

V For a full 50% specified minimum use the following ratings:

O-

R 7618 6091
13430
RS

calculations were performed to meet

4

T 3463E (6091)
O-

I 7618
7500 10500 OSHPD criteria. Derated Derated
RSL (3463)
4

3409 4773
C Capacity Defl. Capacity Defl.
A T R SO 10500
To use OSHPD submitted rated
SL

-S2 (4773) Size (Ibs)(kg) (in)(mm) Size (Ibs) (kg) (in)(mm)

L I LR 6507
RS

C SO
2958 load curves:
O-

4400
2000 -2
4400 B2-450 410 186 1.83 46 2-C2-3740 3120 1415 1.67 42
1

A 20006507 1) Calculate Vertical and Horizontal

L (2950)
B2-680 565 256 1.67 42 4-C2-4840 4040 1833 1.67 42
2409
Forces on mountings including
C2-880 800 363 1.82 46 4-C2-6160 5145 2334 1.67 42
SLRSO-B 1092 translations and overturning moments. C2-1210 1010 458 1.67 42 4-C2-7480 6245 2833 1.67 42
1401 4800 6007 11754 14000
2) Plot Horizontal and Vertical Loads. C2-1540 1285 583 1.67 42 6-C2-7260 6060 2749 1.67 42
637 2182 2730 5343 6350 The intersection must fall within the C2-1870 1560 708 1.67 42 6-C2-9240 7715 3500 1.67 42
HORIZONTAL area below the OSHPD curve. 2-C2-1760 1600 726 1.67 42 6-C2-11220 9370 4250 1.67 42
6007 11754 14000
(2723) (5343) (6350) 2-C2-2420 2020 916 1.67 42 9-C2-13860 11570 5248 1.67 42
TYPE SLRSO and SLRS DIMENSIONS (inches and mm)
HORIZONTAL 2-C2-3080 25701166 1.67 42 9-C2-16830 14050 6373 1.67 42
Type & Size H T D E L HCL W HCW MBD
SLRSO- 83/4 3/8 1/2 11/8 81/2 7 41/4 23/4 5/8
B 222 10 13 29 216 178 108 70 16 SPRING CHARACTERISTICS (inches and mm)
SLRSO- 83/4 3/8 5/8 13/8 91/2 71/2 51/4 31/2 5/8
Spring Free Ratio Ratio
B2 222 10 16 35 241 191 133 89 16 Size OD Height Kx/Ky OD/OH
SLRSO- 83/4 3/8 5/8 13/8 14 121/4 51/4 31/2 5/8
C2 222 10 16 35 356 311 133 89 16 B 23/8 60 40/0 102 0.55-0.65 0.95-1.00
B2 23/8 60 41/2 114 0.80-0.90 1.19-1.48
SLRSO- 83/4 3/8 7/8 13/8 133/4 11 8 61/4 3/4
C2 27/8 73 50/0 127 0.63-0.85 0.96-1.15
4-C2 222 10 22 35 350 279 203 159 19
SLRSO- 3
9 /4 3 /8 1 5
1 /8 19 15 /87 9 6 1 All springs without “ ” have additional travel to solid equal to
††

6-C2 248 10 25 41 483 403 229 152 25 50% of the rated deflection.
SLRS- 93/4 5/8 1 2 18 153/4 13 103/4 1 Solid Spring Height = Free Height minus 1.5 times the Rated
9-C2 248 16 25 51 457 400 330 273 25 Deflection.
3
 SLRSO & SLRSOEBP MASON INDUSTRIES

TYPE SLRSOEBP and SLRSEBP RATINGS 2” 50mm Deflection Series

SLRSOEBP (Extended Base Plate) SLRSOEBP
Rated
Capacity
Rated
Defl
Mount
Constant
Max. Horiz.
G Rating Bolted Spring
2” 50mm Deflection B, B2 & C2, 2-C2, 4-C2,
Illustration shows Size (Ibs) (kg) (in) (mm) (Ibs/in)(kg/mm) to Concrete† Color
6-C2 & 9-C2 Springs a SLRSOEBP-4- B-20 20 9 2.40 61 8 0.15 70.0 Tan
"D" Tap– 4 Holes. Load Ratings are based C2 housing with B-26 26 12 2.18 55 12 0.22 53.9 Wht/Blue
on bolting to two opposed holes. E four C springs. B-35 35 16 2.20 56 16 0.29 40.0 Purple
E E B-50 50 23 2.20 56 24 0.41 28.0 Wht/Red
Vertical Limit
Stops– Out of E B-65 65 29 2.10 53 31 0.55 21.6 Brown
contact during B-85 85 39 2.10 53 40 0.74 16.5 Wht/Blk
normal operation B-115 115 52 2.00 51 57 1.02 12.2 Silver
Adjustment H
B-150 150 68 2.00 51 75 1.33 6.8 Orange
Rubber Bolt B2-210 210 95 2.12 54 99 1.76 9.3 Silver
Snubbing B2-290 290 132 2.00 51 144 2.59 4.9 Blue
Collar
B2-450†† 450 204 2.00 51 224 4.00 3.2 Tan
MBD– T B2-680†† 680 308 2.00 51 340 6.04 2.1 Gray
Max Bolt C2-125 125 57 2.50 64 50 0.89 35.5 Purple
Diameter C2-170 170 77 2.40 61 70 1.26 26.1 Brown
C2-210 210 95 2.30 58 90 1.64 21.1 Red
HCL C2-260 260 118 2.20 56 120 2.11 17.1 White
C2-330 330 150 2.00 51 165 2.94 13.5 Black
L C2-460 460 209 2.00 51 230 4.10 9.6 Blue
C2-610 610 277 2.00 51 305 5.43 7.3 Green
HCW HCL C2-880 ††
880 399 2.00 51 440 7.82 5.0 Gray
W C2-1210†† 1210 549 2.00 51 605 10.8 3.7 Silver
Lower"D" Tap– 4 Holes. Load Ratings are based C2-1540 ††
1540 699 2.00 51 770 13.7 2.9 Gray*
Vertical Limit
Stops– Out Restraining
of on bolting to two opposed holes.
C2-1870†† 1870 848 2.00 51 935 16.6 2.4 Silver*
Nut
contact during E
normal operation Steel Internal
E Neoprene 2-C2-340 340 154 2.40 61 140 2.52 17.7 Brown
E Housing Acoustical Pad 2-C2-420 420 191 2.30 58 180 3.29 14.3 Red
E 2-C2-520 520 236 2.20 56 240 4.21 11.6 White
Adjustment
SLRSOEBP-
Bolt 2-C2-660 660 299 2.00 51 330 5.86 9.1 Black
B & B2 2-C2-920 920 417 2.00 51 460 8.18 6.5 Blue
MBD– HCL 2-C2-1220 1220 553 2.00 51 610 10.8 4.9 Green
Max Bolt 2-C2-1760†† 1760 798 2.00 51 880 15.7 3.4 Gray
Rubber Diameter 2-C2-2420†† 2420 1098 2.00 51 1210 21.5 2.5 Silver
H Snubbing 2-C2-3080†† 3080 1397 2.00 51 1540 27.4 1.9 Gray*
Collar 2-C2-3740 ††
3740 1696 2.00 51 1870 33.2 1.6 Silver*
T 4-C2-4840†† 4840 2195 2.00 51 2420 43.0 1.9 Silver
4-C2-6160†† 6160 2794 2.00 51 3080 54.8 1.5 Gray*
HCL 4-C2 7480 ††
7480 3393 2.00 51 3740 66.5 1.2 Silver*
Steel
HCW L HCLHousing 6-C2-7260 ††
7260 3293 2.00 51 3630 64.6 1.4 Silver
W 6-C2-9240 ††
9240 4191 2.00 51 4620 82.2 1.1 Gray*
14830
ower (6727)Internal Neoprene
Restraining 6-C2-11220 11220 5089 2.00 51 5610 99.8
††
0.9 Silver*
xis

SLRSOEBP-2-C2 SLR Acoustical Pad

Nut SLRSEBP Size
°A

SO HCL
45

Non-Skid Pad is used 14637 in Non-Seismic -6 zones only.

9-C2-13860††13860 6287 2.00 51 6930 123.2 ‡ Gray*
Remove pad prior V (6653) Reduce published
to bolting.
SL

9-C2-16830††16830 7634 2.00 51 8415 149.7 ‡ Silver*

RS

height by 1/8" if pad E is removed. 13430

HCL
O-

(6091)
R 7618 SLRSEBP-9-C2 *
4

T (3463) 7500 with Red inner spring ‡SLRSEBP-9 under test

10500
SLRSOEBP-B I S&
LR B2
(3409)have(4773)one B or B2 spring, SLRSOEBP-2-C2 has two †
C
C2 springsA and SLRSEBP-9-C2 SO
has nine C2 springs and has closed Horizontal load ratings expressed in G’s are based on
SL

-2
calculations with bolted connections to steel on top and concrete
RS

sides. NotL shown is(2958) SLRSOEBP-C2, which has one C2 spring and
6507
inserts on bottom. SLRSOEBP housings require uniform support
O-

4400
SLRSOEBP-6-C2 (2000) which has six C2 springs.
4400
1

(2000) under entire base plate.

OSHPD OPA-1942409 All mounts except SLRSEBP-9-C2 are awaiting
Rated Load Curves SLRSO-B (lbs(1092)
kg)
OSHPD-194 approval. SLRSEBP-9-C2 has not
††
Published ratings allow minimum 25% additional travel to solid.
14830 1401 4800 6007 been 11754 submitted.
14000
For a full 50% specified minimum use the following ratings:
6727 (637) (2182) (2730) (5343) (6350)
Derated Derated
xi s

SL HORIZONTALHorizontal, Vertical and 45° plotted Ratings are

°A

RS
Capacity Defl. Capacity Defl.
45

O-
14637 6 California OSHPD submitted values having the
V 6653 Size (Ibs)(kg) (in)(mm) Size (Ibs) (kg) (in)(mm)
SL

OSHPD Anchorage Preapproval Number OPA-

RS

E 13430
0194. Testing and calculations were performed
O-

R 7618 6091
B2-450 410 186 1.83 46 2-C2-3740 3120 1415 1.67 42
4

T 3463
I SL
7500
3409
10500 to meet OSHPD criteria. B2-680 565 256 1.67 42 4-C2-4840 4040 1833 1.67 42
C 4773
A
RS
O To use OSHPD submitted rated load curves: C2-880 800 363 1.82 46 4-C2-6160 5145 2334 1.67 42
SL

-2
L C2-1210 1010 458 1.67 42 4-C2-7480 6245 2833 1.67 42
RS

6507
2958 1) Calculate Vertical and Horizontal Forces on
O-

4400
2000 4400 C2-1540 1285 583 1.67 42 6-C2-7260 6060 2749 1.67 42
1

2000 mountings including translations and overturning C2-1870 1560 708 1.67 42 6-C2-9240 7715 3500 1.67 42
2409 moments. 2-C2-1760 1600 726 1.67 42 6-C2-11220 9370 4250 1.67 42
SLRSO-B 1092
2) Plot Horizontal and Vertical Loads. The 2-C2-2420 2020 916 1.67 42 9-C2-13860 11570 5248 1.67 42
1401 4800 6007 11754 14000
637 2182 2730 5343 6350 intersection must fall within the area below the 2-C2-3080 2570 1166 1.67 42 9-C2-16830 14050 6373 1.67 42
HORIZONTAL OSHPD curve.
TYPE SLRSOEBP and SLRSEBP DIMENSIONS (inches and mm) SPRING CHARACTERISTICS (inches and mm)
Type & Size H T D E L HCL W HCW MBD Spring Free Ratio Ratio
SLRSOEBP- 9 3/8 1/2 11/8 13 101/2 5 – 5/8 Size OD Height Kx/Ky OD/OH
B 229 10 13 29 330 267 127 – 16 B 23/8 60 40/0 102 0.55-0.65 0.95-1.00
SLRSOEBP- 9 3/8 5/8 13/8 10 8 10 8 5/8 B2 23/8 60 41/2 114 0.80-0.90 1.19-1.48
B2 & C2 229 10 16 35 254 203 254 203 16 C2 27/8 73 50/0 127 0.63-0.85 0.96-1.15
SLRSOEBP- 9 3/8 5/8 13/8 141/2 11 11 9 3/4
2-C2 229 10 16 35 368 280 280 229 19 All springs without “††” have an additional travel to solid equal
SLRSOEBP- 9 3/8 7/8 13/8 19 8 14 11 3/4 to 50% of the rated deflection.
4-C2 229 10 22 35 482 203 356 280 19 Solid Spring Height = Free Height minus 1.5 times the Rated
SLRSOEBP- 101/4 1/2 1 15/8 27 12 15 12 1 Deflection.
6-C2 260 13 25 41 686 305 381 305 25 SP1004
Designs using these mounts to resist wind loads must be in 04/10
SLRSEBP- 101/4 5/8 1 2 27 12 19 16 1 accordance with ASCE 7-05.
9-C2 260 16 25 51 686 305 483 406 25 Printed
in U.S.A.