ITECH ELECTRONICS

IT8500+ Programmable DC Electronic Load Your Power Testing Solution

IT8500+ Programmable DC
Electronic Load

Electronic Load
IT8500+ series single channel programmable
electronic load with high density, high resolution
and high accuracy supports dynamic test
function, automatic test function, etc., which is
suited for applications in areas such as LED
driver testing, switching power testing, battery
performance testing, etc. IT8500+ also provides
standard SCPI protocol to build intelligent test
platform that is ideal for multiple industries.

Applications
Battery test, lithium protection board test, power supply test, charger test, ATE, component
test, etc.

Feature Optional interface

IT-E121 RS232 communication cable
Four operating modes: CV, CC, CR, CP IT-E122 USB communication cable
Battery test function, automatic test function, OPP test, OCP test
function and CR-LED function
Dynamic mode up to 10kHz
Voltage measurement resolution up to 0.1mV / 0.1mA
Remote sense
Short circuit function Automatic Test Function
Current monitoring function
Power-off memory function IT8500+ supports two automatic test editing
100 groups memory capacity modes. One is special automatic test editing
Optional USB / RS232 / RS485 interface mode that can save up to 10 groups of test files,
and the other is compatible with the IT8500
*IT8514B+, IT8514C+, and IT8516C+ are built-in RS232 and USB interface.
automatic test editing mode that can save up to
50 groups of test files, both of which can be
Model Voltage Current Power Size called and tested at any time. Test operation is
IT8511A+ 150V 30A 150W 1/2 2U simple, the button can be completely locked to
IT8511B+ 500V 10A 150W 1/2 2U prevent accidental touch on the keyboard from
IT8512A+ 150V 30A 300W 1/2 2U affecting normal testing.
IT8512B+ 500V 15A 300W 1/2 2U
IT8512C+ 120V 60A 300W 1/2 2U
IT8512H+ 800V 5A 300W 1/2 2U
IT8513A+ 150V 60A 400W 1/2 2U
IT8513C+ 120V 120A 600W 1/2 2U
IT8514B+ 500V 60A 1500W 2U
IT8514C+ 120V 240A 1500W 2U
IT8516C+ 120V 240A 3000W 4U

05/ For more information, please visit ITECH official website

www.itechate.com
 ITECH ELECTRONICS
Your Power Testing Solution IT8500+ Programmable DC Electronic Load

Continuous Mode
Constant Current（CC）
In continuous mode, the electronic load

Electronic Load
V generates a repetitive pulse stream that toggles
In CC mode, the electronic load will sink a between two load levels. Load could switch the
constant current regardless of the changes state between two value settings, A/B.
of input voltage.
I
CC mode

Constant Voltage（CV）
V
In CV mode, the electronic load will attempt
to sink enough current to control the source
voltage to the programmed value.
I
Pulse Mode
CV mode
In pulse mode, the electronic load generates a
transient pulse of programmable width when
Constant Resistance（CR） pulse transient operation is in effect. The load
will automatically switch to A level after
maintaining A width time. Then it will switch to B
In CR mode, the module will sink a current V
linearly proportional to the input voltage in level. The load will not switch to A level again
accordance with the programmed until the instrument receives the pulse signal.
resistance.
I
CR mode

Constant Power（CW）

In CP mode, the electronic load will dissipate

V
power in accordance with the programmed
value.
If input voltage increase, input current will Toggle Mode
decrease. I In toggle mode, the electronic load will switch
CW mode
between A level and B level when receiving a
trigger signal after the transient operation is
enabled. The following picture shows the current
Transient Mode waveform in toggle transient operation.

Transient operation enables the module to periodically switch between

two load levels, as might be required for testing power supplies.
Transient operation can be turned on and off from the front panel (shift
+ numeric key”2”). Before you turn on the operation, you should set
the parameters associated with the transient operation. The
parameters include: A level, B level,frequency, duty cycle and transient
testing modes. There are three different transient testing modes:
continuous, pulse, and toggle.

For more information, please visit ITECH official website

www.itechate.com /06
 ITECH ELECTRONICS
IT8500+ Programmable DC Electronic Load Your Power Testing Solution

List Mode Remote Sense

Electronic Load

List mode allows you to generate a complex current sequence. When working in CC, CV, CP and CR mode, if
Moreover, the mode change can be synchronized with an internal or the electronic load consumes a very large
external signal, to accomplish dynamic and precise test which can current, it will cause a voltage drop in the leads
save cost for users. Users can edit step value, pulse width and slope between the connected device and terminals of
sequence and meet a complex test request. A list file includes the electronic load. In order to ensure testing
following parameters: file name step counts (range 2-84), time width of accuracy, the electronic load provides a pair of
single step (0.00005s-3600s), step value and slope. The edited list file remote sensing terminals in the rear panel where
can be recalled easily. The DC load provides 7 nonvolatile registers to users can sense the output terminal voltage of
save list files setting for recall later. In the list mode, the load starts to the connected device. Users should set the
run the list file once receiving a trigger signal, continue to run until end electronic load in REMOTE SENSE mode before
of the operation or receiving another trigger. using this function. By eliminating the effect of
the voltage drop in the load leads, remote
sensing provides greater accuracy by allowing
the electronic load to regulate directly at the
source's output terminals.

Battery Mode

Battery discharge test of IT8500+ series can be achieved under CC

mode. There are three cut-off conditions for IT8500+ include cut-off
voltage, cut-off capacity and cut-off time, when any of the three conditions
are met, discharge test will be stopped, the load will be automatically
switched to OFF. Moreover, the battery voltage, discharge time and
discharged capacity can be observed during the test.

07/ For more information, please visit ITECH official website

www.itechate.com
 ITECH ELECTRONICS
Your Power Testing Solution IT8500+ Programmable DC Electronic Load

IT8500+ Specifications

Electronic Load
IT8511A+ IT8511B+ IT8512A+
Rated Voltage 0~150V 0~500V 0~150V
( 0～40 ℃) Current 0~3A 0~30A 0~3A 0~10A 0~3A 0~30A
Power 150W 150W 300W
MOV 0.25V at 3A 3V at 30A 1.2V at 3A 4V at 10A 0.14V at 3A 1.4V at 30A
CV mode Range 0~18V 0~150V 0.1~50V 0.1~500V 0.1~18V 0.1~150V
Resolution 1mV 10mV 1mV 10mV 1mV 10mV
Accuracy ±(0.05%+0.025%FS) ±(0.05%+0.025%FS) ±(0.05%+0.05%FS) ±(0.05%+0.05%FS) ±(0.05%+0.02%FS) ±(0.05%+0.025%FS)
CC mode Range 0~3A 0~30A 0~3A 0~10A 0~3A 0~30A
Resolution 0.1mA 1mA 0.1mA 1mA 0.1mA 1mA
Accuracy ±(0.05%+0.05%FS) ±(0.05%+0.05%FS) ±(0.05%+0.05%FS)
CR mode Range 0.1Ω~10Ω 10Ω~7.5KΩ 0.5Ω~10Ω 10Ω~7.5KΩ 0.05Ω~10Ω 10Ω~7.5KΩ
Resolution 16bit 16bit 16bit
Accuracy 0.01%+0.08S *2 0.01%+0.0008S 0.01%+0.08S *2 0.01%+0.0008S 0.01%+0.08S *2 0.01%+0.0008S
CP mode Range 150W 150W 300W
Resolution 10mW 10mW 10mW
Accuracy ±（0.1%+0.1%FS） ±(0.1%+0.2%FS) ±（0.1%+0.1%FS）
Dynamic mode T1&T2 20uS~3600S /Res:1 uS 20uS~3600S /Res:1 uS 20uS~3600S /Res:1 uS
Accuracy 2uS±100ppm 2uS±100ppm 2uS±100ppm
Min response time Up/down slope 0.0001~0.12A/Us≒10uS 0.001~0.6 A/uS≒10uS 0.0001~0.2A/uS≒10uS 0.001~0.8A/uS ≒10uS 0.0001~0.2A/uS 0.001~1.5A/uS
Measuring range
Readback Range 0~18V 0~150V 0~50V 0~500V 0~18V 0~150V
Voltage Resolution 0.1 mV 1mV 1 mV 10 mV 0.1 mV 1 mV
Accuracy ±(0.025%+0.025%FS) ±(0.025%+0.025%FS) ±(0.025%+0.025%FS)
Readback Range 0~3A 0~30A 0~3A 0~10A 0~3A 0~30A
Current Resolution 0.1mA 1mA 0.1mA 1mA 0.1mA 1mA
Accuracy ±(0.05%+0.05%FS) ±(0.05%+0.05%FS) ±(0.05%+0.05%FS)
Readback Range 150W 150W 300W
Power Resolution 10mW 10mW 10mW
Accuracy ±(0.1%+0.1%FS) ±(0.1%+0.2%FS) ±(0.1%+0.1%FS)
Protected range
Over power protection ≒160W ≒160W ≒320W
Over current protection ≒3.3A ≒33A ≒3.3A ≒11A ≒3.3A ≒33A
Over voltage protection ≒160V ≒530V ≒160V
Over temperature protection ≒85℃ ≒85℃ ≒85℃
Specification
Short circuit CC ≒3.3/3A ≒33/30A ≒3.3/3A ≒11/10A ≒3.3/3A ≒33/30A
CV ≒0V ≒0V ≒0V
CR ≒80mΩ ≒400mΩ ≒180mΩ
Input terminal impedance ≒300KΩ ≒1MΩ ≒300KΩ
Size(W*H*D) 214.5mm*88.2mm*354.6mm 214.5mm*88.2mm*354.6mm 214.5mm*88.2mm*354.6mm

*This information is subject to change without notice

IT8511A+ / IT8512A+/ IT8511B+ / IT8512B+ / IT8512C+ / IT8512H+ / IT8513A+/ IT8513C+

① Air vents
② Voltage switch（110V/220V）
③ AC line input
④ Current monitoring Terminal
⑤ 9-Pin serial port interface connector
⑥ Trigger and remote sensing terminal block

For more information, please visit ITECH official website

www.itechate.com /08
 ITECH ELECTRONICS
IT8500+ Programmable DC Electronic Load Your Power Testing Solution

IT8500+ Specifications
IT8512B+ IT8512H+
Rated Voltage 0~500V 0~800V
( 0～40 ℃) Current 0~3A 0~15A 0~1A 0~5A
Electronic Load

Power 300W 300W

MOV 0.6V/3A 3V/15A 1.4V at 1A 7V at 5A
CV mode Range 0.1~50V 0.1~500V 0.1~80V 0.1~800V
Resolution 1mV 10mV 1mV 10mV
Accuracy ±(0.05%+0.05%FS) ±(0.05%+0.05%FS) ±(0.05%+0.05%FS) ±(0.05%+0.05%FS)
CC mode Range 0~3A 0~15A 0~1A 0~5A
Resolution 0.1mA 1mA 0.1mA 1mA
Accuracy ±(0.05%+0.05%FS) ±(0.05%+0.05%FS) ±(0.05%+0.1%FS) ±(0.05%+0.05%FS)
CR mode Range 0.3Ω~10Ω 10Ω~7.5KΩ 2Ω~10Ω 10Ω~7.5KΩ
Resolution 16bit 16bit
Accuracy 0.01%+0.08S 0.01%+0.0008S 0.01%+0.08S*2 0.01%+0.0008S
CP mode Range 300W 300W
Resolution 10mW 10mW
Accuracy ±（0.1%+0.2%FS） 0.2%+0.2%FS
Dynamic mode T1&T2 20uS~3600S /Res:1 uS 20uS~3600S /Res:1 uS
Accuracy 2uS±100ppm 2uS±100ppm
Min response time Up/down slope 0.0001~0.2A/uS≒10uS 0.001~0.8A/uS ≒10uS 0.0001~0.04A/uS≒20uS 0.001~0.2A/uS ≒20uS
Measuring range
Readback Range 0~50V 0~500V 0~80V 0~800V
Voltage Resolution 1 mV 10 mV 1 mV 10 mV
Accuracy ±(0.025%+0.025%FS) ±(0.025%+0.025%FS)
Readback Range 0~3A 0~15A 0~1A 0~5A
Current Resolution 0.1mA 1mA 0.1mA 1mA
Accuracy ±(0.05%+0.05%FS) ±(0.05%+0.05%FS)
Readback Range 300W 300W
Power Resolution 10mW 10mW
Accuracy ±(0.1%+0.2%FS) ±(0.2%+0.2%FS)
Protected range
Over power protection ≒320W ≒320W
Over current protection ≒3.3A ≒16A ≒1.1A ≒5.5A
Over voltage protection ≒530V ≒850V
Over temperature protection ≒85℃ ≒85℃
Specification
Short circuit CC ≒3.3/3A ≒16/15A ≒1.1/1A ≒5.5/5A
CV ≒0V ≒0V
CR ≒180mΩ ≒1.4Ω
Input terminal impedance 1MΩ 2MΩ
Size(W*H*D) 214.5mmW*354.6mmD*88.2mmH 214.5mmW*354.6mmD*88.2mmH

IT8513A+ IT8513C+
Rated Voltage 0~150V 0~120V
( 0～40 ℃) Current 0~6A 0~60A 0~12A 0~120A
Power 400W 600W
MOV 0.25V at 6A 2.5V at 60A 0.2V at 12A 2V at 120A
CV mode Range 0.1~18V 0.1~150V 0.1~18V 0.1~120V
Resolution 1mV 10mV 1mV 10mV
Accuracy ±(0.05%+0.02%FS) ±(0.05%+0.025%FS) ±(0.05%+0.02%FS ±(0.05%+0.025%FS)
CC mode Range 0~6A 0~60A 0~12A 0~120A
Resolution 0.1mA 1mA 1mA 10mA
Accuracy ±(0.05%+0.05%FS) ±(0.05%+0.05%FS) ±(0.05%+0.05%FS) ±(0.05%+0.1%FS)
CR mode Range 0.1Ω~10Ω 10Ω~7.5KΩ 0.05Ω~10Ω 10Ω~7.5KΩ
Resolution 16bit 16bit
Accuracy 0.01%+0.08S 0.01%+0.0008S 0.01%+0.08S *2 0.01%+0.0008S
CP mode Range 400W 600W
Resolution 10mW 10mW
Accuracy ±(0.2%+0.2%FS) ±（0.2%+0.2%FS）
Dynamic mode T1&T2 100uS~3600S /Res:1 uS 100uS~3600S /Res:1 uS
Accuracy 10uS+100ppm 10uS±100ppm
Min response time Up/down slope 0.001~0.15A/uS 0.01~1 A/uS 0.001~0.2A/uS≒60uS 0.01~1.6A/uS ≒60uS
Measuring range
Readback Range 0~18V 0~150V 0~18V 0~120V
Voltage Resolution 0.1 mV 1mV 0.1 mV 1mV
Accuracy ±(0.025%+0.025%FS) ±(0.025%+0.025%FS)
Readback Range 0~6A 0~60A 0~12A 0~120A
Current Resolution 0.1mA 1mA 1mA 10mA
Accuracy ±(0.05%+0.05%FS) ±(0.05%+0.05%FS) ±(0.05%+0.05%FS) ±(0.05%+0.1%FS)
Readback Range 400W 600W
Power Resolution 10mW 10mW
Accuracy ±(0.2%+0.2%FS) ±(0.2%+0.2%FS)
Protected range
Over power protection ≒420W ≒620W
Over current protection ≒6.6A ≒66A ≒13A ≒130A
Over voltage protection ≒165V ≒125V
Over temperature protection ≒85℃ ≒95℃
Specification
Short circuit CC ≒6.6/6A ≒66/60A ≒13/12A ≒130/120A
CV ≒0V ≒0V
CR ≒30mΩ ≒15mΩ
Input terminal impedance ≒280KΩ 150KΩ
Size(W*H*D) 214.5mm*88.2mm*453.5mm 214.5mm*88.2mm*453.5mm
*This information is subject to change without notice

09/ For more information, please visit ITECH official website

www.itechate.com
 ITECH ELECTRONICS
Your Power Testing Solution IT8500+ Programmable DC Electronic Load

IT8500+ Specifications
IT8514C+ IT8514B+ IT8516C+

Electronic Load
Rated Voltage 0~120V 0~500V 0~120V
( 0～40 ℃) Current 0~24A 0~240A 0~6A 0~60A 0~24A 0~240A
Power 1500W 1500 W 3000W
MOV 0.25V at 24A 2.5V at 240A 0.5V at 6A 3V at 60A 0.15V at 24A 1.5V at 240A
CV mode Range 0~18V 0.1~120V 0.1~50V 0.1~500V 0.1~18V 0.1~120V
Resolution 1mV 10mV 1mV 10mV 1mV 10mV
Accuracy ±(0.05%+0.02%FS ±(0.05%+0.025%FS) ±(0.05%+0.05%FS) ±(0.05%+0.05%FS) ±(0.05%+0.02%FS) ±(0.05%+0.025%FS)
CC mode Range 0~24A 0~240A 0~6A 0~60A 0~24A 0~240A
Resolution 1mA 10mA 1mA 10mA 1mA 10mA
Accuracy ±(0.1%+0.1%FS) ±(0.1%+0.1%FS) ±(0.05%+0.05%FS) ±(0.05%+0.05%FS) ±(0.1%+0.1%FS) ±(0.1%+0.1%FS)
CR mode Range 0.05Ω~10Ω 10Ω~7.5KΩ 0.05Ω~10Ω 10Ω~7.5KΩ 0.05Ω~10Ω 10Ω~7.5KΩ
Resolution 16bit 16bit 16bit
Accuracy 0.02%+0.08S 0.01%+0.0008S 0.02%+0.08S *1 0.02%+0.0008S 0.02%+0.08S *1 0.02%+0.0008S
CP mode Range 1500W 1500W 3000W
Resolution 10mW 10mW 10mW
Accuracy ±（0.2%+0.2%FS） ±（0.2%+0.2%FS） ±（0.2%+0.2%FS）
Dynamic mode T1&T2 100uS~3600S /Res:1uS 100uS~3600S /Res:1 uS 120uS~3600S /Res:1 uS
Accuracy 10uS±100ppm 10uS±100ppm 10uS±100ppm
Min response time Up/down slope 0.001~0.3A/uS 0.01~3.2A/uS 0.001~0.15A/uS≒60uS 0.01~0.8A/uS≒60uS 0.001~0.25A/uS≒70uS 0.01~2.4A/uS≒70uS
Measuring range
Readback Range 0~18V 0~120V 0~50V 0~500V 0~18V 0~120V
Voltage Resolution 0.1 mV 1mV 0.1 mV 1mV 0.1 mV 1mV
Accuracy ±(0.025%+0.025%FS) ±(0.025%+0.025%FS) ±(0.025%+0.025%FS)
Readback Range 0~24A 0~240A 0~6A 0~60A 0~24A 0~240A
Current Resolution 1mA 10mA 1mA 10mA 1mA 10mA
Accuracy ±(0.05%+0.05%FS) ±(0.05%+0.05%FS) ±(0.1%+0.1%FS)
Readback Range 1500W 1500W 3000W
Power Resolution 10mW 10mW 10mW
Accuracy ±(0.2%+0.2%FS) ±(0.2%+0.2%FS) ±(0.2%+0.2%FS)
Protected range
Over power protection ≒1550W ≒1550W ≒3050W
Over current protection ≒26.7A ≒267A ≒6.7A ≒67A ≒26A ≒260A
Over voltage protection ≒125V ≒530V ≒125V
Over temperature protection ≒85℃ ≒85℃
Specification
Short circuit ≒26.7/24A ≒267/240A ≒6.7/6A ≒67/60A ≒26/24A ≒260/240A
≒0V
CC
CV ≒0V ≒0V
CR ≒8mΩ ≒50mΩ ≒6mΩ
Input terminal impedance 300KΩ 1MΩ 300KΩ
Size(W*H*D) 436.5mm*88.2mm*463.5mm 436.5mm*88.2mm*463.5mm 436.5mm*176mm*463.5mm

*1 Resistance readback range:（ 1/(1/R+(1/R)*0.01%+0.08),1/(1/R-(1/R)*0.01%-0.08) ）

IT8514B+/14C+/16C+：（ 1/(1/R+(1/R)*0.02%+0.08),1/(1/R-(1/R)*0.02%-0.08) ）

*This information is subject to change without notice

IT8514B+/IT8514C+ Dimension figure

unit: mm

For more information, please visit ITECH official website

www.itechate.com /10