OPERATOR HANDBOOK

WSG
1068
Gasoline
LIQUEFIED PETROLEUM GAS (LPG)
NATURAL GAS (NG) ENGINES

Part #: 1080050
EDI Revision F
March , 2011
W

Downloaded from www.Manualslib.com manuals search engine

 ARNING:

Downloaded from www.Manualslib.com manuals search engine

 FORD WSG-1068 ENGINES

Gasoline
LIQUEFIED PETROLEUM GAS (LPG)
NATURAL GAS (NG)

Reproduction in any manner, in whole or in part, is prohibited without the

express permission in writing from

Engine Distributors Incorporated

Engine Distributors policy is one of continuous improvement and while every effort is made to
ensure that this publication is up to date and correct in all respects, the right to change prices,
specifications and equipment at any time without notice is reserved. Accordingly this publication is
not to be regarded as a final description of any individual engine.

Downloaded from www.Manualslib.com manuals search engine

 CONTENTS
HEALTH & SAFETY .......................................................................................................... 4
General Guidelines: ................................................................................................ 4
Important Safety Notice........................................................................................... 4
Notes, Cautions, and Warnings .............................................................................. 5

FORWARD ........................................................................................................................ 6

ENGINE IDENTIFICATION................................................................................................ 6
U.S.A. Engine Identification Decal .......................................................................... 7
Non-Certified Engine Decal..................................................................................... 7
Federal Emissions Warranty Statement.................................................................. 8
California Emission Control Warranty Statement.................................................... 8
What Is Covered? .................................................................................................. 10
European Service Identification Plate .................................................................... 11

PARTS AND SERVICE..................................................................................................... 12

SERVICE LITERATURE................................................................................................... 12

WARRANTY REGISTRATION ......................................................................................... 12

BEFORE OPERATING THE ENGINE.............................................................................. .13

OPERATING CONTROLS................................................................. ............................... 13

Ignition or Isolation Switch ..................................................................................... 13
Safety Switch (where fitted) ................................................................................... 14
Power Take-off (where fitted)................................................................................. 14
Throttle Control (where fitted) ................................................................................ 14

INSTRUMENTS................................................................................................................. 15
Ammeter (Where Fitted)......................................................................................... 15
Battery Condition Indicator (Where Fitted)............................................................. 15
Tachometer (Where Fitted) ................................................................................... 15
Hourmeter (Where Fitted) ...................................................................................... 15
Oil Pressure Gauge (Where Fitted)........................................................................ 15
Temperature Gauge (Where Fitted)....................................................................... 16
Malfunction Indicator Light (Where Fitted) ............................................................. 16
Charge Indicator Light (Where Fitted).................................................................... 16
Safety Switch Override Button (Where Fitted) ....................................................... 16
Ignition or Isolation Switch ..................................................................................... 16
Fuel Select Switch (Where Fitted).......................................................................... 16

STARTING THE ENGINE.................................................................................................. 17

Initial Start-up ......................................................................................................... 17
To Start From cold ................................................................................................. 17
To Re-start When Warm ........................................................................................ 17

Downloaded from www.Manualslib.com manuals search engine

 CONTENTS
STOPPING THE ENGINE ................................................................................................ 18
Normal Conditions.................................................................................................. 18
Abnormal Conditions.............................................................................................. 18

RUNNING-IN PROCEDURE ............................................................................................ 18

FUEL RECOMMENDATION............................................................................................. 19

LUBRICATION AND MAINTENANCE.............................................................................. 19

RECOMMENDED MAINTENANCE SCHEDULES........................................................... 20

RECOMMENDED MAINTENANCE OPERATIONS ........................................................ 21

Recommended Lubricants .................................................................................... 21
Used Engine Oils .................................................................................................. 22
Change Engine Oil ............................................................................................... 22
Check Engine Oil Level......................................................................................... 23
Renew Engine Oil Filter ........................................................................................ 23
Ignition System...................................................................................................... 24
Renew Spark Plugs............................................................................................... 24
Electronic Actuator ............................................................................................... 26
Check Condition of Ancillary Drive Belts............................................................... 26
Check Engine Coolant Level................................................................................. 26
Renew Air Cleaner Element.................................................................................. 27
Renew PCV Valve................................................................................................. 27

GENERAL MAINTENANCE INFORMATION .................................................................. 28

Cooling System..................................................................................................... 28
Draining, Flushing and Filling the Cooling System................................................ 30
Engine Lubrication System ................................................................................... 30
Electrical System................................................................................................... 31
Generator ............................................................................................................. 32
Storage.................................................................................................................. 33

ENGINE SYSTEM CHECK.............................................................................................. 34

SPECIFICATIONS .......................................................................................................... 38

TIGHTENING TORQUES................................................................................................ 39

CONVERSION TABLE ....................................................................................... ............40

FORD POWER PRODUCTS SERVICE ......................................................................... 41

Downloaded from www.Manualslib.com manuals search engine

 HEALTH & SAFETY

WARNING: THE FOLLOWING HEALTH AND SAFETY RECOMMENDATIONS SHOULD BE

CAREFULLY OBSERVED.

Carrying out certain operations and handling some substances can be dangerous or harmful to the
operator if the correct safety precautions are not observed. Some such precautions are
recommended at the appropriate points in this book.

While it is important that these recommended safety precautions are observed, care near
machinery is always necessary, and no list can be exhaustive. ALWAYS BE ON YOUR GUARD!

General Guidelines:
The following recommendations are for general guidance:
1. Always wear correctly fitting protective clothing which should be laundered
regularly. Loose or baggy clothing can be extremely dangerous when working on running q
engines or machinery. Clothing which becomes impregnated with oil or other substances
can constitute a health hazard due to prolonged contact with the skin even through
underclothing.
2. So far as practicable, work on or close to engines or machinery only when they are stopped.
If this is not practicable, remember to keep tools, test equipment and all parts of the body
well away from the moving parts of the engine or equipment—fans, drive belts and pulleys
are particularly dangerous. The electric cooling fan used on some installations is actuated
automatically when the coolant reaches a specified temperature. For this reason, care
should be taken to ensure that the ignition/isolating switch is OFF when working in the
vicinity of the fan as an increase in coolant temperature may cause the fan suddenly to
operate.
3. Avoid contact with exhaust pipes, exhaust manifolds and silencers when an engine is, or
has recently been running; these can be very hot and can cause severe burns.
4. Many liquids used in engines or vehicles are harmful if taken internally or splashed into the
eyes. In the event of accidentally swallowing gasoline (petrol), oil, diesel fuel, antifreeze,
battery acid etc., DO NOT ENCOURAGE VOMITING AND OBTAIN QUALIFIED MEDICAL
ASSISTANCE IMMEDIATELY.

Wear protective goggles when handling liquids which are harmful to the eyes these include
ammonia and battery acid. If any of these substances are splashed in the eyes, wash out
thoroughly with clean water and OBTAIN QUALIFIED MEDICAL ASSISTANCE IMMEDIATELY.

Important Safety Notice

Appropriate service methods and proper repair procedures are essential for the safe, reliable
operation of all industrial engines as well as the personal safety of the individual doing the work.
This operator handbook provides general directions for accomplishing service and repair work with
tested, effective techniques. Following them will help assure reliability.

There are numerous variations in procedures, techniques, tools and parts for servicing equipment,
as well as in the skill of the individual doing the work. This manual cannot possibly anticipate all
such variations and provide advice or cautions as to each. Accordingly, anyone who departs from
the instructions

Downloaded from www.Manualslib.com manuals search engine

 provided in this Manual must first establish that neither personal safety nor equipment integrity are
compromised by the choice of methods, tools or parts.

Notes, Cautions, and Warnings

As you read through the procedures, you will come across NOTES, CAUTIONS, and WARNINGS.
Each one is there for a specific purpose. NOTES gives you added information that will help you to
complete a particular procedure. CAUTIONS are given to prevent you from making an error that
could damage the equipment. WARNINGS remind you to be especially careful in those areas
where carelessness can cause personal injury. The following list contains some general
WARNINGS that you should follow when you work on the equipment.

GENERAL WARNINGS:
• Always wear safety glasses for eye protection.
• Use safety stands whenever a procedure requires you to be under the
equipment.
• Be sure that the ignition switch is always in the OFF position, unless otherwise
required by the procedure.
• Set the parking brake (if equipped) when working on the equipment. If you have
an automatic transmission, set it in PARK REVERSE (engine off) or NEUTRAL
(engine on) unless instructed otherwise for a specific operation. Place wood
blocks (4”x 4” or larger) to the front and rear surfaces of the tires to provide
further restraint from inadvertent equipment movement.
• Operate the engine only in a well ventilated area to avoid the danger of carbon
monoxide.
• Keep yourself and your clothing away from moving parts when the engine is
running, especially the fan belts.
• To prevent serious burns, avoid contact with hot metal parts such as the
radiator, exhaust manifold, tail pipe, catalytic converter and muffler.
• Do not smoke while working on the equipment.
• To reduce the risk of injury, always remove rings, watches, loose hanging
jewelry, and loose clothing before beginning to work on the equipment. Tie long
hair securely behind the head.
• Keep hands and other objects clear of the radiator fan blades. Electric cooling
fans can start to operate at any time by an increase in underhood temperatures,
even though the ignition is in the OFF position. Therefore, care should be taken
to ensure that the electric cooling fan is completely disconnected when working
under the hood.

Downloaded from www.Manualslib.com manuals search engine

 FORWARD
This book contains operating and maintenance instructions for the engine(s) listed on the title
page.

The life of your engine unit and the delivery of the high performance built into it will depend on the
care it receives throughout its life. It is the operator’s responsibility to ensure that the engine is
correctly operated and that the maintenance operations outlined in this book are carried out
regularly after the specified hours of operation have been reached. We consider it to be in your
interests to enlist the aid of an authorized Ford Power Products Distributor not only when repairs
are required but also for regular maintenance. Distributors are listed at the back of this handbook.

Regular maintenance will result in minimal operating costs.

Engines manufactured by Ford Motor Company are available through Ford Power
Products Distributors. When in need of parts or service, contact your local Authorized Distributor.
In overseas territories, in the event of difficulties, communicate directly with the supervising Ford
affiliated Company in your area whose address appears at the end of this book.

Where the terms “Right” or “Left” occur in this publication, they refer to the respective sides of the
engine when viewed from the rear or flywheel end.

Pistons and valves are numbered from the front or timing cover end of the engine commencing at
No. 1.

You may find that your engine assembly includes optional equipment not specifically covered in
the following text. Nevertheless, the maintenance procedures outlined in this book still apply to
your engine

ENGINE IDENTIFICATION
Because Engine Distributors has such a wide range of industrial gasoline and diesel engines -
manufactured both in the U.S. and overseas - it is important that you have as complete
identification of the engine as possible in order to provide the correct replacement parts. Review
the list of distributors for a distributor in your area. You can obtain a standard parts listing
describing the parts. It remains a distributor function to identify the part number.

The key to identifying the engine is the identification decal mounted on the engine rocker cover.
That decal provides not only the engine serial number, but also the exact model or type,
configuration code and customer name. The combination of that data permits you to isolate the
precise engine, build level and customer so you can determine the correct replacement parts.

Downloaded from www.Manualslib.com manuals search engine

 EDI Engine Identification Decal
An identification Decal is affixed to the valve cover of the engine. The decal contains the engine serial number which
identifies this unit from all others. Use all numbers when seeking information or ordering replacement parts for this
engine.

For handy reference, transfer the data recorded on this decal to a safe place.

Your Warranty Rights and Obligations

The California Air Resources Board, U.S. EPA and Engine Distributors, Inc. are pleased to explain the
emission control system warranty on your new 2010 and subsequent model year emission certified engine
(or brand equipment). New off-road large spark-ignition (LSI) engines must be designed, built and equipped
to meet stringent Federal and State anti-smog standards. Engine Distributors, Inc. warrants that the
emission control system on your engine for the periods of time listed below provided there has been no
abuse, neglect or improper maintenance of your engine.

Your emission control system may include parts such as the carburetor, regulator or fuel-injection system,
ignition system, engine computer unit (ECM), catalytic converter and air induction system. Also included
may be sensors, hoses, belts, connectors and other emission-related assemblies.

Where a warrantable condition exists, Engine Distributors, Inc will repair your LSI engine at no cost to you
including diagnosis, parts, and labor.
Manufacturer’s Warranty Coverage
Standard warranty for any non-emissions related part is two years or 2000 hours. This includes the base
engine and ancillary parts such as the starter and alternator.

The new 2010 model year off-road large spark-ignition engines are warranted for three years or 2500 hours
of service, whichever occurs first from the date the equipment is delivered to the first retail purchaser or
when the equipment is first placed in service. If any emission-related part on the engine is defective, the
part will be repaired or replaced by an authorized Engine Distributors, Inc. dealer. This is your General
Emissions Warranty.

For five years or 3500 hours of service (whichever occurs first) if any emission-related part specially noted
with coverage for five years or 3500 hours is defective, the part will be repaired or replaced by and
authorized Engine Distributors, Inc. dealer. This is your High Priced Parts Emission Warranty.

Downloaded from www.Manualslib.com manuals search engine

 Owner’s Warranty Responsibilities
As the off-road LSI engine owner, you are responsible for the performance of the required maintenance
listed in your owner’s manual. Engine Distributors, Inc. recommends that you retain all records covering
maintenance on your off-road engine, but Engine Distributors, Inc. cannot deny warranty solely for the lack
of receipts or for your failure to ensure the performance of all scheduled maintenance.

As the off-road large spark-ignition engine owner, you should however be aware that Engine Distributors,
Inc. may deny you warranty coverage if your off-road large spark-ignition engine or a part has failed due to
abuse, neglect, improper maintenance or unapproved modifications.

Depending on the model of engine you have purchased, your engine may be designed to operate on LPG,
Gasoline, and/or Natural Gas fuels. Use of any other fuel may result in your engine no longer operating in
compliance with applicable emissions requirements.

You are responsible for initiating the warranty process. Engine Distributors suggests that you present your
off-road large spark-ignition engine to an Engine Distributors, Inc. dealer as soon as a problem exists. The
warranty repairs should be completed by the dealer as expeditiously as possible.

If you have any questions regarding your warranty rights and responsibilities, you should contact Engine
Distributors, Inc. at (800) 220-2700.
What is Covered
Below is a list of the systems that affect emissions on your engine. Emission control components on these
systems are covered by the emissions warranties as applicable.

If failure of one of the components listed below results in failure of another part, both will be covered by this
warranty. For detailed information concerning specific components covered by these emission control
systems warranties, ask your dealer.

General Emissions Warranty Parts List – 3 years or 2,500 hours, whichever comes first
• Fuel Metering System
o Fuel injection system.
o Air/fuel ratio feedback and control system.
o Carburetor system (internal parts and/or pressure regulator or fuel mixer or injection system).
• Air Induction System
o Air intake system.
• Catalyst or Thermal Reactor System
• Positive Crankcase Ventilation (PCV) System.
o PCV Valve.
o Oil Filler Cap.
• Ignition Control System
o Ignition module(s).
o Spark Plugs
• Miscellaneous items Used in Above Systems
o Vacuum, temperature, and time sensitive valves and switches.
o Sensors used for electronic controls.
o Hoses, belts, connectors, assemblies, clamps, fittings, tubing, sealing gaskets or devices,
and mounting hardware.
o Pulleys, belts and idlers.

Downloaded from www.Manualslib.com manuals search engine

 • Emission Related Components (Only Covered if Your Engine was Sold in California)
o Air Induction System
o Fuel System
o Ignition System
o Exhaust Gas Recirculation Systems
o After Treatment Devices
o Crankcase Ventilation Valves
o Sensors
o Electronic Control Units
o Fuel Tank
o Fuel Cap
o Fuel Line
o Fuel Line Fittings
o Clamps
o Pressure Relief Valves
o Control Valves
o Control Solenoids
o Electronic Controls
o Vacuum Control Diaphragms
o Control Cables
o Control Linkages
o Purge Valves
o Vapor Hoses
o Liquid/Vapor Separator
o Carbon Canister
o Canister Mounting Brackets
o Carburetor Purge Port Connector

High Priced Emissions Warranty Parts List – 5 years or 3,500 hours, whichever comes first:
• Press Regulator
• Catalytic Muffler
• Engine Control Module (ECM).
• Intake Manifold
• Exhaust Manifold
• Harness
• Throttle

Downloaded from www.Manualslib.com manuals search engine

 SERVICE LITERATURE

A service manual can be purchased from your EDI distributor. This publication will provide the
necessary servicing and overhaul information for your Ford Power Products engine.

• WSG1068 SERVICE MANUAL - EDI

• WSG1068 PARTS LIST - EDI

BEFORE OPERATING THE ENGINE

1. Before operating a new engine it should be thoroughly inspected to ensure that during
transit and installation it has not suffered damage likely to affect its subsequent operation.
Controls and instruments should be studied carefully in order that their functions are
thoroughly understood.
2. Check that the radiator (where applicable) is full and top off as necessary -- Refer to
“Cooling System” on page 28 for recommended coolant mixtures.
3. In the case of marine/industrial engines, ensure that there is coolant in the degas/expansion
tank (where applicable).

CAUTION: Under no circumstances may the engine be started without liquid in the cooling
system.

4. Check the engine oil level and top up or fill as necessary -- Refer to “Check Engine Oil
Level” on page 23. For the correct type and grade of oil -- Refer to “Recommended
Lubricants” on page 21.
5. Ensure that the battery is fully charged and, if necessary, top up with distilled water.

NOTE: Ensure that ALL wiring ground connections are properly made to a clean point on the
chassis/frame.
6. The engine must be started in accordance with the starting instructions -- Refer
to “STARTING THE ENGINE” on page 17.

OPERATING CONTROLS

Ignition or Isolation Switch

An ignition or isolation switch is usually fitted which connects the engine starter motor and other
electrical equipment to the battery. The switch can be moved to any of the four positions shown by
rotating the key. These positions are:

Downloaded from www.Manualslib.com manuals search engine

 1. Auxiliary Circuits - When moved to this position the auxiliary electrical equipment such as
radios and heater fans, can be operated without also connecting the starting circuit with the
battery.
2. Off - When set to this position, the switch disconnects the auxiliary electrical equipment and
the starting circuit from the battery. The key can be removed from the switch when it is in
this position; this will help to prevent unauthorized operation of the engine.
3. Run - This switch position connects the auxiliary circuits as described previously, and the
alternator is given initial excitation via the battery.
4. Start - In this position, the starter solenoid is energized and the starter motor cranks the
engine. The switch, when released, automatically returns to the RUN position.
Safety Switch (where fitted)
A low oil pressure/high water temperature safety switch may be fitted. This automatically shuts off
the ignition when the oil pressure drops below a pre-set value, or when the water temperature rises
above a pre-set value. A button on the instrument panel is used to override the safety switch when
starting the engine. The safety switch override button must be depressed to start the engine.

NOTE: With EDI GCP safety shut-down incorporated oil pressure below 6 psi and/ or coolant
temperature goes above 250° F, will shut-down ignition system. Corrective action must be taken
and key recycled to restart.

Power Take-off (where fitted)

The power take-off control handle allows engagement and disengagement of the power take-off
clutch. Moving the lever towards the engine engages the clutch and moving the lever away from
the engine disengages the clutch.

When moving the handle to engage the clutch and pick up the load, do so in a smooth manner.
Moving the clutch handle too slowly will cause slippage and wear, while moving it too fast will
cause quick engagement and possible damage to the power take-off, engine or driven equipment.
The normal force required to engage the clutch is 55 lbf (245 N) for the over-centre type and 25 lbf
(110 N) for the spring loaded type.

Throttle Control (where fitted)

The throttle control adjusts engine speed. Initial engine speed adjustment is obtained by pressing
the throttle control release button while pulling the throttle knob out to increase the engine speed or
pushing it in to decrease the engine speed. A final fine speed adjustment is obtained by turning the
throttle control counterclockwise to increase engine speed or clockwise to decrease engine speed.

Downloaded from www.Manualslib.com manuals search engine

 INSTRUMENTS

Your Ford Powered Equipment will have been fitted with instruments selected by the manufacturer.
The types of instruments most likely to be encountered are detailed here. A typical instrument
panel is shown below.

Ammeter (Where Fitted)

This instrument registers the charging current which is being passed to the battery from the
alternator. It also registers a discharge equivalent to the amount of current being used by the
electrical equipment when the alternator is not charging.

Battery Condition Indicator (Where Fitted)

This is sometimes fitted instead of an ammeter and measures the battery voltage thus indicating
the state of charge of the battery.

Tachometer (Where Fitted)

The tachometer indicates the actual engine running speed in crankshaft revolutions per minute.

Hourmeter (Where Fitted)

This instrument records the number of hours of operation which the engine has completed at the
rated rpm. It is frequently combined with the tachometer and is used to determine when an engine
service operation is required. If no hourmeter is fitted, a log should be kept.

Oil Pressure Gauge (Where Fitted)

The oil pressure gauge registers the lubricating system pressure in bar (kgf/cm2 or Ibf/in2) and
should be frequently observed to ensure that the system is functioning correctly.

Temperature Gauge (Where Fitted)

The temperature gauge enables a close check to be kept on the coolant temperatures.

Malfunction Indicator Light (Where Fitted)

Used on all industrial engines. This light will illuminate whenever there is an engine malfunction
such as low oil pressure, high engine temperature, fuel injection system fault. The engine can be
programmed to shut down in the event of a malfunction.

Downloaded from www.Manualslib.com manuals search engine

 Charge Indicator Light (Where Fitted)
If an alternator is fitted to your engine, a charge indicator light will also be fitted. The light will glow
when the isolating switch is in the RUN position with the engine stationary and will therefore serve
as a reminder either to turn the isolating switch to the OFF position or to start the engine. Once the
engine has started, the charge indicator light should cease glowing.

Safety Switch Override Button (Where Fitted)

This must be depressed when starting the engine, as the safety switch operates when the oil
pressure falls due to the engine stopping -- Refer to “Safety Switch (where fitted)” on page 14.

Ignition or Isolation Switch

-- Refer to “Ignition or Isolation Switch” on page 13.

Fuel Select Switch (Where Fitted)

This switch is incorporated for use with dual fuels. Switch must point to selection of fuel being
used.

Downloaded from www.Manualslib.com manuals search engine

 STARTING THE ENGINE

WARNING: ALL INTERNAL COMBUSTION ENGINES GIVE OFF VARIOUS FUMES AND
GASES WHILE RUNNING. DO NOT START OR RUN THE ENGINE IN A CLOSED OR POORLY
VENTILATED BUILDING WHERE THE EXHAUST GASES CAN ACCUMULATE. AVOID
BREATHING THESE GASES AS THEY MAY CONTAIN POISONOUS CARBON MONOXIDE
WHICH CAN ENDANGER YOUR HEALTH OR LIFE IF INHALED STEADILY FOR EVEN A FEW
MINUTES.

Initial Start-up
On initial start-up follow the daily regular maintenance schedule illustration -- Refer
to “RECOMMENDED MAINTENANCE SCHEDULES” on page 20.

To Start From cold

1. Where possible, disconnect the driven equipment, eg, fully depress the clutch
where a manual transmission is fitted. If your unit is equipped with the engine warning light
system, always turn the ignition switch to the ON position to make sure that each warning
light is operating before starting engine.
2. Switch on the ignition and operate the starter motor until the engine fires.

NOTE: Where a safety switch is fitted, the override button must be depressed while
the engine is being cranked.
3. Set the throttle to give a fast idle speed until normal operating temperature is reached
(where fitted).

CAUTION: If the engine stalls or falters in starting, wait 3-4 seconds before re-engaging
starter. This will prevent possible damage to the starter or engine. The starter should not
operate for periods longer than 30 seconds at a time. An interval of at least two minutes
should be observed between such cranking periods to protect the starter from overheating.

To Re-start When Warm

Switch on the ignition and operate the starter motor until the engine starts.

NOTE: Safety shut-down incorporated in the Ignition Performance Module (IPM): Oil pressure
below 6 psi and/or coolant temperature goes above 250°F, will shutdown the ignition system.

NOTE: The IPM will also shut the engine off when engine speed reaches 2250 rpm for Gen-Set
and 4000 rpm for all other applications. Key must be recycled to restart.

NOTE: Where a safety switch is fitted, the override button must be depressed while the engine is
being cranked.

Downloaded from www.Manualslib.com manuals search engine

 STOPPING THE ENGINE

Normal Conditions
Following normal operating conditions, lower the engine speed to idle, disengage the clutch, and
then turn the ignition switch to the OFF position. If the engine has been running under high power,
let it run at fast idle speed a few minutes to cool the engine down.

Abnormal Conditions
Under abnormally overheated conditions, the engine may continue to run after the ignition switch is
turned off. If this case is ever encountered, turn on the ignition switch immediately and allow the
engine to idle until it has cooled enough to stop. If the engine is overheated due to loss of coolant,
it is best to stop the engine immediately, if necessary by applying the load. Add engine oil if
necessary, then after the engine has returned to a normal temperature, add coolant slowly until the
radiator is full.

WARNING: TO REDUCE THE RISK OF INJURY WHEN CHECKING A HOT ENGINE. COVER
THE RADIATOR CAP IN A THICK CLOTH AND TURN IT SLOWLY COUNTERCLOCKWISE TO
THE FIRST STOP. AFTER THE PRESSURE HAS BEEN COMPLETELY RELEASED, PRESS
THE CAP DOWNWARD AND FINISH REMOVING THE CAP.

The above instructions also apply to engines that stop due to operation of the low oil pressure/high
water temperature safety switch. However, if the engine stops due to low oil pressure, do not
restart until the cause has been determined and corrected -- Refer to “Recommended Lubricants”
on page 21.

RUNNING-IN PROCEDURE
A new or reconditioned engine must not be run at high speeds or on full load for the first 25 hours.
The load and speed may be increased to a maximum over this period. After the first 50 hours
running, carry out the maintenance operations listed
-- Refer to “RECOMMENDED MAINTENANCE SCHEDULES” on page 20.

Check the instruments frequently and keep the coolant and oil filled to their recommended levels.

Downloaded from www.Manualslib.com manuals search engine

 FUEL RECOMMENDATION
This engine is designed to operate on dry fuel such as LPG Grade HD5 or NG (1050 BTU/ft^3).

CAUTION: Use of fuels rated lower than the grades specified above may cause persistent,
heavy spark knock, which can lead to engine damage. If your engine knocks heavily, or if
you hear continuous spark knock while maintaining constant operating speeds, consult
your distributor or another qualified technician.

LUBRICATION AND MAINTENANCE

The importance of correct lubrication, periodic inspection and adjustment cannot be over-
emphasized. It will determine, to a very large extent, the service the engine will give. Detailed
instructions regarding this maintenance are given in the following pages.

Your Authorized EDI Distributor listed in the back section of this manual, will be pleased to carry
out this regular maintenance for you. The various maintenance operations are listed -- Refer to
“RECOMMENDED MAINTENANCE SCHEDULES” on page 20.

When carrying out any of the following maintenance operations, any fault or malfunction should be
reported immediately to the supervisor or person responsible for engine overhaul or repair.

The following Maintenance Schedules give the maximum recommended service periods. Since
operating conditions can vary, it may be advisable to carry out some operations, for example,
changing the engine oil, at an interim period. Your operating experience is the best guide for
determining this time.

Downloaded from www.Manualslib.com manuals search engine

 RECOMMENDED MAINTENANCE

*It is recommended that this operation is carried out by an authorized Ford Distributor. Depending
upon the quality of the fuel used, it may be necessary to renew the filter element more frequently.

** PCV Valve inspection and Spark Plug replacement are recommended at the interval(s)
described. Spark plug cleaning/replacement at these intervals will ensure maximum engine
performance, fuel economy, and emissions. Failure to complete recommended maintenance does
not disqualify your engine from any emissions related warranty coverage’s

Downloaded from www.Manualslib.com manuals search engine

 RECOMMENDED MAINTENANCE OPERATIONS

Recommended Lubricants

CAUTION: Do not use supplemental oil additives or other engine treatments. They are
unnecessary and could, under certain conditions, lead to engine damage which is not
covered by Ford warranty.

Lubricating oil cleanliness is vital for the successful operation of your engine. The oil should be
stored under the cleanest possible conditions. When changing or topping-up engine oil use only
clean receptacles. Do not allow the oil to come into contact with rubber hoses on the engine.

CAUTION: Use Ford/Motorcraft “Formula E” SAE 5W-

20 engine oil or equivalent that meets Ford
Specification ESEM2C153-C(API Classification – SJ).
If SJ oils are not available, SH oils are acceptable.
Use only engine oil displaying the American
Petroleum Institute Certification Mark on the front of
the container, or API specification SH, or SJ.

NOTE: Ford Power Products industrial engines are designed to perform with engine oils that are
licensed by the American Petroleum Institute (API), and oils carrying the most current API
classification should be used. API classifications are broken into two categories, gasoline and
diesel engines. API’s classification is designated by a two letter system. The first letter, the prefix,
designates gasoline or diesel. An “S’’ designates gasoline and a “C’’ designates diesel. The
second letter in the system designates the level of the classification. It should be noted that
alternative fuel engines fall into the “gasoline’’ API category.

Gasoline engines that are converted for LPG or Natural Gas applications must use
oils labeled SH and/or SJ. Do not use oils that are specifically formulated for Diesel
Engines only. CC or CD classification, even when labeled Heavy Duty or for
Natural Gas Engines, are not acceptable. The use of SAE 5W-20 is recommended
for all temperatures:

Downloaded from www.Manualslib.com manuals search engine

 Used Engine Oils

WARNING: PROLONGED AND REPEATED CONTACT MAY CAUSE SERIOUS SKIN

DISORDERS INCLUDING DERMATITIS AND SKIN CANCER.

WARNING: AVOID EXCESSIVE CONTACT—WASH THOROUGHLY AFTER CONTACT. KEEP

OUT OF THE REACH OF CHILDREN.

WARNING: PROTECT THE ENVIRONMENT: IT IS ILLEGAL TO POLLUTE DRAINS, WATER

COURSES OR SOIL. USE AUTHORIZED FACILITIES FOR DISPOSAL. IF IN DOUBT,
CONTACT YOUR LOCAL AUTHORITY FOR ADVICE.

WARNING: DO NOT HANDLE A HOT OIL FILTER WITH BARE HANDS. CONTINUOUS
CONTACT WITH USED MOTOR OIL HAS CAUSED SKIN CANCER IN LABORATORY MICE.
PROTECT YOUR SKIN BY WASHING WITH SOAP AND WATER IMMEDIATELY AFTER
CONTACT.

Change Engine Oil

1. Warm the engine to normal operating temperature.
2. Make sure that the equipment is standing level and that the engine is stopped.
3. Obtain a sufficiently large draining pan to accommodate the engine oil -- Refer to “Service Oil fill
capacity (including filter):” on page 38.
4. Remove the oil filler cap from the rocker cover, remove the drain plug from the oil pan and drain
the oil into the draining pan.

NOTE: Modern high performance oils have a cleaning action on the engine which may turn the oil
dark, but does not necessarily indicate inadequate oil changes.
5. Replace and tighten the drain plug, then fill the engine via the filler neck in the rocker cover with
the correct quantity of oil -- Refer to “SPECIFICATIONS” on page 38.
6. Replace the oil filler cap and run the engine for no more than 30 seconds.
7. Check the oil level as described in the following section.

Downloaded from www.Manualslib.com manuals search engine

 Check Engine Oil Level
1. Make sure the equipment is standing level and
that the engine is stopped.
2. Pull out the dipstick and wipe it with a clean rag.
3. Insert the dipstick fully and again remove it. At no
time should the level of the oil fall below the lower
mark on the dipstick.
4. If necessary, top up to the dipstick higher mark
with an approved type and grade of oil.
5. Replace the dipstick, ensuring that it is fully
inserted into its tube to maintain a sealed crankcase
condition

Renew Engine Oil Filter

CAUTION: The original oil filter is not available for service. Use the recommended
Motorcraft FL-820S.

Your engine is equipped with a Motorcraft oil filter. A

filter of this quality should be used throughout the life
of the engine. It is designed to protect your engine by
filtering harmful abrasive and sludgy particles
without clogging up or blocking the flow of the oil to
vital engine parts. This filter is especially designed for
use in engines built by Ford to give successful
operation with the recommended oil filter change
intervals. Contact your nearest EDI
Distributor/Dealer listed in the back section
to obtain the correct filter. Before commencing, place a
drain pan beneath the filter to catch any spilt oil.

1. Using a suitable strap wrench, unscrew the oil filter

canister.
2. Thoroughly clean oil filter housing face.
3. Partly pre-fill the new filter with clean engine oil of the correct type and grade. Apply a thin film of
clean engine oil to the oil filter sealing ring.
4. Screw on new oil filter canister until sealing ring abuts the filter head and tighten a further 1/2
turn. Do NOT use a strap wrench or similar tool to tighten the filter canister.
5. Run engine and check for any leaks from oil filter.
6. Stop engine, allow oil to settle and top up as necessary.

Downloaded from www.Manualslib.com manuals search engine

 Ignition System
The 6.8L engine is equipped with a coil-on-plug ignition system. Rather than a
remotely mounted coil with secondary ignition wires, this system has a separate
ignition coil mounted on each spark plug. Operation of the coils is controlled by the
engine computer module (GCP), which computes ignition timing based on inputs from
engine sensors.

Renew Spark Plugs

WARNING: THE IGNITION SYSTEM COMMONLY CARRIES VOLTAGES IN EXCESS OF

30,000 VOLTS. PLEASE USE CAUTION.

CAUTION: Do not pull directly on the lead as this could cause the wire connection
inside the boot to become separated.

NOTE: To remove spark plugs you must first remove coils.

1. Disconnect the ignition coil wire connectors.
2. Remove the hold down screw then the coil.
NOTE: For fuel rail clearance rotate coils 45° clockwise and lift out.
3. After loosening each spark plug one or two turns with a proper spark plug spanner, clean the
area around each spark plug port with compressed air then remove the spark plugs.

WARNING: PROTECTIVE GOGGLES MUST BE WORN TO PROTECT THE

EYES WHEN USING COMPRESSED AIR.

Downloaded from www.Manualslib.com manuals search engine

 4. Check the gaps of the new spark plugs with a feeler
gauge, and, where necessary, bend the outer
ground extension to achieve the specified gap.

5. Use a proper spark plug spanner to avoid damaging

the insulators, screw the new spark plugs into the
cylinder head and tighten them to the specified
torque value listed under specification of this manual.

NOTE: Do not over tighten spark plugs as the gap may

change considerably due to the distortion of the plug
outer shell.

6. Coat the inside of each spark plug boot with silicone

dielectric compound D7AZ-1 9A33 1-A (USA) or equivalent,
using a small nscrewdriver blade.

7. Install the plug coils and tighten hold down bolt to 5-7 Nm (44-62 in-lb).

NOTE: Coils are interchangeable.

8. Reconnect ignition coil wire connectors.

Downloaded from www.Manualslib.com manuals search engine

 Electronic Actuator
In the event that your engine is equipped with an electronic actuator, any
necessary adjustment should be made by your Power Products Distributor listed at
the back of this manual. The adjusting procedure requires the use of tools which
are not readily available to consumers

Check Condition of Ancillary Drive Belts

WARNING: ENGINE SHOULD BE STOPPED AND ANY REMOTE STARTER

DISABLED BEFORE CHECKING BELTS.

The serpentine ancillary belt used to drive the generator and water pump, is tensioned
automatically and does not require adjustment.

The belts should be visually inspected for signs of wear or damage. It should be renewed if
necessary. Refer to Service Manual.

NOTE: May be purchased from your local Ford Power Product Distributor listed on the back of this
handbook.

Check Engine Coolant Level

WARNING: TO REDUCE THE RISK OF INJURY WHEN CHECKING A HOT ENGINE. COVER
THE RADIATOR CAP WITH A THICK CLOTH AND TURN IT SLOWLY COUNTER-CLOCKWISE
TO THE FIRST STOP. AFTER THE PRESSURE HAS BEEN COMPLETELY RELEASED,
PRESS DOWNWARD AND FINISH REMOVING CAP. FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN DAMAGE TO THE COOLING SYSTEM OR ENGINE AND/
OR PERSONAL INJURY.

CAUTION: Do not add coolant to an engine that has become overheated until the engine
cools. Adding coolant to an extremely hot engine can result in a cracked block or cylinder
head.

1. Allow the engine to cool down to 40°C (110°F).

2. Turn the radiator expansion/degas tank filler cap through 90° in a counterclockwise direction.
Pause to allow any pressure to drop, then turn cap fully counterclockwise and remove it.
3. The quantity of coolant in the expansion/degas tank is a direct indication of the coolant level in
the complete system. The acceptable level of coolant in the expansion/degas tank is shown by the
level indicators moulded into the tank wall. Top up as necessary with a mixture of plain water and
antifreeze -- Refer to “Cooling System” on page 28 for information on mixing antifreeze solutions.

NOTE: It is essential that only the correct type of antifreeze is used -- Refer to “Cooling System” on
page 28.

4. Replace the filter cap and turn down tightly.

Downloaded from www.Manualslib.com manuals search engine

 Renew Air Cleaner Element
Your air cleaner filters air entering the engine induction system and acts as a silencer and a flame
arrester. Air that contains dirt and grit produces an abrasive fuel mixture, and can cause severe
damage to the cylinder walls and piston rings. Damage to the cylinder walls and piston rings will
cause high oil consumption and short engine life. A restricted or dirty air cleaner will also cause a
rich fuel mixture. Thus, it is extremely important that the air cleaner be serviced at recommended
intervals.

CAUTION: Service the air cleaner more frequently under severe dust conditions to prevent
engine damage.

1. Release the air cleaner lid retaining hardware.

2. Lift the air cleaner lid clear of the air cleaner body, then remove the air cleaner element and
discard it.
3. Wipe the inside of the air cleaner body and lid clean, using a lint-free rag.
4. Insert the new element, ensuring that it fits properly and install air cleaner lid.

Renew PCV Valve

1. Detach the hose, from the top of the
PCV valve located at the top rear of right
valve cover and from the intake manifold.
2. Withdraw the PCV valve from the valve
cover grommet.
3. Discard the PCV valve and the ‘O’ ring.
4. Thoroughly clean the inside and outside
of the hose.
5. Insert the new PCV valve, complete
with a new ‘O’ ring.
6. Re-connect the hose to the PCV valve
and to the intake manifold.

Downloaded from www.Manualslib.com manuals search engine

 GENERAL MAINTENANCE INFORMATION
The following section outlines some aspects of general maintenance which will be of value to the
operator.

Cooling System
To obtain maximum engine service life, its operating temperature must be maintained by an
efficient cooling system.

CAUTION: Under no circumstances should the engine be started without liquid

in the cooling system. This may cause permanent damage to the engine.

Inspect the exterior of the radiator for obstructions, remove all bugs, dirt or foreign material with a
soft brush or cloth.

Use care to avoid damaging the fins. If available, use low pressure compressed air or a stream of
water in the opposite direction to normal airflow. Check all hoses and connections for leaks. If any
of the hoses are cracked, frayed, or feel spongy, they should be replaced.

CAUTION: Never use a cold coolant mixture to top-up the radiator or degas tank of a hot
engine if the coolant level is very low; this could cause serious engine damage.

The radiator or degas tank is equipped with a pressure cap. It is dangerous to

remove this when the system is very hot.

WARNING: NEVER REMOVE THE PRESSURE RELIEF CAP WHILE THE ENGINE IS
OPERATING OR WHEN THE COOLING SYSTEM IS HOT. MAY CAUSE PERSONAL INJURY
OR DAMAGE TO COOLING SYSTEM OR ENGINE. TO REDUCE THE RISK OF HAVING
SCALDING HOT COOLANT OR STEAM BLOW OUT OF THE DEGAS BOTTLE WHEN
REMOVING THE PRESSURE RELIEF CAP, WAIT UNTIL THE ENGINE HAS COOLED DOWN
TO AT LEAST 40°C (110°F).

1. Wrap a thick cloth around the pressure relief cap and turn it slowly one-half turn
counterclockwise. Stepping back while the pressure is released from the cooling system.

2. When you are sure all the pressure has been released, (still with a cloth) turn counterclockwise
and remove the pressure relief cap.

In territories where freezing conditions may occur, the coolant should consist of a mixture of 50%
plain water and 50% Motorcraft Super Plus 2000 coolant. This
antifreeze contains additional corrosion inhibitors designed to provide lasting protection for the
engine.

Only this antifreeze, or proprietary antifreeze meeting Ford specification WSSM97B44-

D or Ford specification ESE-M97B44-A should be used when topping-up or re-filling the cooling
system.

Motorcraft Super Plus 2000 coolant has long life characteristics and if the concentration is kept to a
maximum of 50% it will provide adequate frost protection and inhibiting for the life of the engine.

Downloaded from www.Manualslib.com manuals search engine

 NOTE: If a major component of the cooling system is renewed such as the radiator, water pump
etc., the system should be flushed and re-filled with a 50% solution of Motorcraft Super Plus 2000
coolant and clean water.

In territories where the ambient temperature is such that no protection against freezing is required,
it is recommended that a 25% concentration of Motorcraft Super Plus 2000 coolant is used. This
will protect water pumps, core plugs, thermostat housings and radiators against corrosion for the
life of the engine and raise boiling point when used at this concentration. See previous Note on
renewing cooling system components.

The antifreeze concentration in a cooling system can be determined by using a

suitable hydrometer.
• A reading of 1080 represents a 50% antifreeze concentration.
• A reading of 1040 represents a 25% antifreeze concentration.
• A reading of 1000 represents plain water.

WARNING: ANTIFREEZE CONTAINS MONO ETHYLENE GLYCOL AND OTHER

CONSTITUENTS WHICH ARE TOXIC IF TAKEN INTERNALLY AND CAN BE ABSORBED IN
TOXIC AMOUNTS ON REPEATED OR PROLONGED SKIN CONTACT. PERSONS USING
ANTIFREEZE ARE RECOMMENDED TO ADHERE TO THE FOLLOWING PRECAUTIONS:

• ANTIFREEZE MUST NEVER BE TAKEN INTERNALLY. IF ANTIFREEZE IS

SWALLOWED ACCIDENTALLY, MEDICAL ADVICE SHOULD BE SOUGHT
IMMEDIATELY.
• PRECAUTIONS SHOULD BE TAKEN TO AVOID SKIN CONTACT WITH
ANTIFREEZE. IN THE EVENT OF ACCIDENTAL SPILLAGE ONTO THE
SKIN, ANTIFREEZE SHOULD BE WASHED OFF AS SOON AS
PRACTICABLE. IF CLOTHING IS SPLASHED WITH ANTIFREEZE, IT
SHOULD BE REMOVED AND WASHED BEFORE BEING WORN AGAIN, TO
AVOID PROLONGED SKIN CONTACT.
• FOR REGULAR AND FREQUENT HANDLING OF ANTIFREEZE,
PROTECTIVE CLOTHING (PLASTIC OR RUBBER GLOVES, BOOTS AND
IMPERVIOUS OVERALLS OR APRONS) MUST BE USED TO MINIMIZE
SKIN CONTACT.

Downloaded from www.Manualslib.com manuals search engine

 Draining, Flushing and Filling the Cooling System

WARNING: NEVER REMOVE THE PRESSURE

RELIEF CAP WHILE THE ENGINE IS
OPERATING OR WHEN THE COOLING SYSTEM
IS HOT. MAY CAUSE PERSONAL
INJURY OR DAMAGE TO COOLING SYSTEM OR
ENGINE. TO REDUCE THE RISK OF HAVING
SCALDING HOT COOLANT OR STEAM BLOW
OUT OF THE DEGAS BOTTLE WHEN REMOVING
THE PRESSURE RELIEF
CAP, WAIT UNTIL THE ENGINE HAS COOLED
DOWN TO AT LEAST 40°C (110°F).

1. Wrap a thick cloth around the pressure relief cap and turn it slowly one-half turn
counterclockwise. Stepping back while the pressure is released from the cooling system.
2. When you are sure all the pressure has been released, (still with a cloth) turn counterclockwise
and remove the pressure relief cap.
3. Remove the radiator expansion/ degas tank filler cap, then open the radiator drain cock, where
fitted, or detach the bottom radiator hose.
4. Flush the system with water using a hose until clean water emerges and allow all water to drain
out. Close the drain cock (or replace the bottom radiator hose). Recover all old antifreeze and
dispose of properly. Contact your local municipal government for the proper disposal.
5. Fill the system with the correct coolant mixture via the expansion/degas tank filler neck. Fill the
system slowly, to avoid air locks, up to the ‘maximum’ mark on the degas tank.
6. Run engine and check hose connections for leaks. Check, and, if necessary, top up the coolant
in the radiator or degas tank.

Engine Lubrication System

The lubrication system should be maintained
regularly -- Refer to “RECOMMENDED
MAINTENANCE SCHEDULES” on page 20,
with the correct grade of lubricant as specified
in the maintenance summary -- Refer to
“Recommended Lubricants” on page 21. The
system is of the force feed type, the lubricating
oil being circulated to the engine bearings
under pressure by an oil pump driven from the
camshaft drive chain belt.

The dipstick provides some guide to the

condition of the oil. An additive type of oil keeps
soot in suspension, and even a small amount
of soot causes the oil to darken rapidly.

However, if the dipstick is found to be heavily

coated with sludge, then obviously the oil should be changed.

Downloaded from www.Manualslib.com manuals search engine

 Electrical System
A NEGATIVE EARTH (NEGATIVE GROUND) SYSTEM IS USED.

GCP - Power Distribution Box

Fuse Amps Circuits protected

1 10 Battery Voltage to EPR

2 5 Ignition Voltage to GCP and Relays

3 10 Battery Voltage to GCP

4 15 Fuel pump

5 15 Battery Voltage out of Power Relay

6 10 Alternator

Generator
This is mounted on a bracket at the front of the engine and is driven from the crankshaft by a
serpentine belt.

The charging rate is adjusted automatically by the built-in regulator to provide sufficient electric
current to keep the battery fully charged under normal operating conditions.

The generator requires no lubrication or maintenance.

WARNING: IT IS ESSENTIAL THAT THE WIRING CONNECTIONS TO THE GENERATOR ARE

NOT REMOVED WHILE THE ENGINE IS RUNNING, AS THIS WILL RESULT IN DAMAGE TO
THE REGULATOR OR PERSONAL INJURY.

Downloaded from www.Manualslib.com manuals search engine

 Storage

Storage - One Month

• While the engine is running, treat upper cylinders by spraying engine fogging agent (from
your local aftermarket supplier) into the air intake for about two minutes. Open throttle for
short burst of speed, shut off engine and allow it to come to a stop while continuing to spray
into air intake.
• Leave spark plugs in holes or seal spark plug holes with suitable threaded metal plugs and
cover all openings into engine with dust-proof caps or shields (suitable non-hygroscopic
material).
• If engine is less transmission, spray flywheel and ring gear with mixture of one part
recommended engine oil, and one part Stoddard Solvent or equivalent.
• Check coolant protection. Store indoors in dry area.

Storage - Indefinite Period

• Drain crankcase completely and refill with recommended engine oil, (SAE 10) or equivalent.
• Run engine and treat upper cylinders by spraying fogging agent into the air intake for about
two minutes. Open throttle for short burst of speed, shut off engine and allow it to come to a
stop while continuing to spray into air intake.
• Check coolant protection
• Disconnect and remove battery.
• Clean exterior surface of engine.
• Leave spark plugs in holes or seal spark plug holes with suitable threaded metal plugs.
• Seal all openings in engine and accessories with non-hygroscopic material. Mask off all
areas to be used for electrical contacts.
• Make sure all surfaces are dry, then spray all taped openings, all engine accessories
including ignition wiring, and all exterior surfaces of engine with Insulation Compound.
• If engines are equipped with automotive type clutch, block clutch in slightly disengaged
position so that lining and pressure plates are not in contact.

Downloaded from www.Manualslib.com manuals search engine

 ENGINE SYSTEM CHECK
GCP System Check
NOTE: Most items listed in the possible cause column may not set a diagnostic fault indicator or
illuminate the MIL light.
NOTE: EDI engines are used in many different applications and equipment. When performing any
system diagnosis be aware of any OEM inputs or equipment monitoring devices that may have an
effect on the engine’s performance or any of the engine’s operating systems.

Engine Performance - No Load

Downloaded from www.Manualslib.com manuals search engine

 Engine Performance - While Under Load

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine
 Engine Concerns

Downloaded from www.Manualslib.com manuals search engine

 SPECIFICATIONS

Downloaded from www.Manualslib.com manuals search engine

 TIGHTENING TORQUES

Downloaded from www.Manualslib.com manuals search engine

 CONVERSION TABLE

Downloaded from www.Manualslib.com manuals search engine

 EDI Distributors

Europe

Downloaded from www.Manualslib.com manuals search engine

 New Zealand

North America - Canada

Downloaded from www.Manualslib.com manuals search engine

 North America - United States

Downloaded from www.Manualslib.com manuals search engine

 North America - United States (Continued)

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine