Scribd Logo
Upload

Welcome to Scribd!

  • 460 views

    API 610 Checklist

    Uploaded by

    Prabha Karan
    The document specifies requirements for electrical motors, surface preparation and painting, spare parts, pump ratings, connections, bearings, mechanical seals, piping, and couplings for offshore pumps. Suction and discharge flanges must have a minimum pressure rating of 300#. Bearings must be oil lubricated. Mechanical seals must be suitable for the process and meet API 682 standards. Piping must meet maximum pressure and temperature ratings.

    Copyright:

    © All Rights Reserved
    Download as XLSX, PDF, TXT or read online from Scribd

    API 610 Checklist

    Uploaded by

    Prabha Karan
    460 views6 pages
    The document specifies requirements for electrical motors, surface preparation and painting, spare parts, pump ratings, connections, bearings, mechanical seals, piping, and couplings for offshore pumps. Suction and discharge flanges must have a minimum pressure rating of 300#. Bearings must be oil lubricated. Mechanical seals must be suitable for the process and meet API 682 standards. Piping must meet maximum pressure and temperature ratings.

    Copyright

    © © All Rights Reserved

    Available Formats

    XLSX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document specifies requirements for electrical motors, surface preparation and painting, spare parts, pump ratings, connections, bearings, mechanical seals, piping, and couplings for offshore pumps. Suction and discharge flanges must have a minimum pressure rating of 300#. Bearings must be oil lubricated. Mechanical seals must be suitable for the process and meet API 682 standards. Piping must meet maximum pressure and temperature ratings.

    Copyright:

    © All Rights Reserved
    Download as XLSX, PDF, TXT or read online from Scribd
    Download as xlsx, pdf, or txt
    460 views6 pages

    API 610 Checklist

    Uploaded by

    Prabha Karan
    The document specifies requirements for electrical motors, surface preparation and painting, spare parts, pump ratings, connections, bearings, mechanical seals, piping, and couplings for offshore pumps. Suction and discharge flanges must have a minimum pressure rating of 300#. Bearings must be oil lubricated. Mechanical seals must be suitable for the process and meet API 682 standards. Piping must meet maximum pressure and temperature ratings.

    Copyright:

    © All Rights Reserved
    Download as XLSX, PDF, TXT or read online from Scribd
    Download as xlsx, pdf, or txt
    You are on page 1of 6

    1

    Seals:

    Painting

    Spares

    Connection
    The minimum + 10 % margin on electrical motor rating vs rated operational duty applies for ratings
    less than 300 kW.

    Surface preparation, painting and final color shall be as per 1923-YINS-98-M-SA-00002_B1_Paint Specification

    Spare parts for startup and commissioning to be included in base scope


    Priced two year operational spare parts list to be provided
    All consumables for installation, commissioning, startup shall be included in the scope.

    Suction & discharge to have same pressure rating

    Minimum 300# as per Process & Marine Pump Spec


    0000-YINS-00-R-SA-00006_C1_Process & Marine Pumps
    Specification

    Specification

    0000-YINS-00-R-SA-00006_C1_Process & Marine Pumps


    Specification
    0000-YINS-00-R-SA-00006_C1_Process & Marine Pumps
    Specification
    Suction flange rating
    1 Flanges
    Discharge flange rating

    Drain Piping
    2 Connection to case
    Vent Piping

    Bearing Type

    Bearing Lubrication

    3 Bearings

    Bearing Housing Sealing

    Constant Level Oilers

    Seal type

    4 Mechanical Seals

    Seal Flush Plan - Primary

    Seal Flush Plan - Secondary

    Cooling Water Plans


    5 Piping
    6 Couplings Coupling Type

    Coupling Guard
    Shall be a minimum of 300#
    Shall be a minimum of 300#

    Pump casing drain shall be flanged connections with isolation valve with flanged ends terminated at skid / base plate edge.

    Self‐venting type centrifugal pumps are preferred. Pumps which are not self‐venting, shall be provided with vent
    connections with isolation valve and terminated with flanged connections.
    horizontal pumps shall be equipped with oil lubricated anti‐friction type
    radial and thrust bearings
    all pump bearings and gear bearings shall be oil lubricated. Pump bearings and gear bearings
    other than anti‐friction type shall be forced lubricated.

    -1” (25 mm) bulls‐eye level indicator shall be provided to monitor the oil level inside the bearing housing.
    -Bearing Housings shall be supplied with bearing isolators.
    -The bearing housing shall be provided with tapped connections for temperature and vibration measurement using portable
    handheld devices.
    -Lip seals shall not be used.

    Constant level oiler (with cage housing)

    -The mechanical seal shall be as per API 682 and be selected based on individual pump design, pump
    operating parameters, process conditions
    -API seal type or classification (dual or single or tandem
    design) shall be for each application approved by Yinson if not already at RFQ stage being predefined
    for each set of service by Yinson.
    -All Topsides pumps handling services as named: Hydrocarbon service, oily water, produced water
    (PW) service, any toxic or hazard service like chemicals, amines, H2S, shall have double mechanical
    seals.

    -Mechanical seals shall be supported with API Plan 53B Auto top‐up provision of seal barrier fluid, and local API Plan 53B
    seal panel ensuring pressurizing and cooling of the dual mechanical seal loop.
    -Pump shall combine the use of throat bushing / wear rings, impeller balance holes or other means, and flush piping
    arrangements to ensure a stuffing box pressure in excess of suction pressure and to provide continuous flow through the
    seal chamber.
    -Mechanical seal system (API plan 53B local panel) and lube oil system shall be mounted on the same skid as the
    equipment.
    -The mechanical seal systems shall be designed such that the interval between each top up / charging of the auto top of
    unit is 14 days or longer, in case of several consumers in same area of module, common reservoir for automatic top ‐up of
    local seal systems shall be aimed for, capacity for local accumulators is minimum 2 hours to accommodate start up and shut
    down scenarios, and any loss of pressurised supply from top up unit.
    -Natural air draught cooling type is the preferred option.

    -All interconnecting tubing/piping within the skid shall be included


    -The temperature and pressure rating of the auxiliary piping handling pumped fluid shall be not less than pump case
    maximum allowable working pressure at maximum specified pumping temperature.

    Coupling guards shall be made of spark‐resistant material. Seaworthy aluminum is acceptable being
    surface treated and painted to offshore standard for such material.
    As Per "0000‐YINS‐00‐R‐SA‐00006-Process & marine pump specification"
    As Per "0000‐YINS‐00‐R‐SA‐00006-Process & marine pump specification"

    As Per "0000‐YINS‐00‐R‐SA‐00006-Process & marine pump specification"

    As Per "0000‐YINS‐00‐R‐SA‐00006-Process & marine pump specification"

    As Per "0000‐YINS‐00‐R‐SA‐00006-Process & marine pump specification"

    As Per "0000‐YINS‐00‐R‐SA‐00006-Process & marine pump specification"

    As Per "0000‐YINS‐00‐R‐SA‐00006-Process & marine pump specification"

    As Per "0000‐YINS‐00‐R‐SA‐00006-Process & marine pump specification"

    As Per "0000‐YINS‐00‐R‐SA‐00006-Process & marine pump specification"

    As Per "0000‐YINS‐00‐R‐SA‐00006-Process & marine pump specification"

    As Per "0000‐YINS‐00‐R‐SA‐00006-Process & marine pump specification"

    You might also like