12d Model

12d View Reference Manual

Version 14
February 2019

12D SOLUTIONS PTY LTD

ACN 101 351 991

PO Box 351 Narrabeen NSW Australia 2101

Australia Telephone (02) 9970 7117 Fax (02) 9970 7118
International Telephone 61 2 9970 7117 Fax 61 2 9970 7118
Email [email protected] Web www.12d.com
12d View Reference Manual

12d View Reference Manual

This book is the reference manual for the software product 12d View.
First Release Dates of Software and Manual
V12.0 January 2017
V14.0 October 2018

Disclaimer
12d View is supplied without any express or implied warranties whatsoever.
No warranty of fitness for a particular purpose is offered.
No liabilities in respect of engineering details and quantities produced by 12d View are accepted.

Every effort has been taken to ensure that the advice given in this manual and the program 12d View is
correct, however, no warranty is expressed or implied by 12d Solutions Pty Ltd.

Copyright
This manual is copyrighted and all rights reserved.
This manual may not, in whole or part, be copied or reproduced without the prior consent in writing from
12d Solutions Pty Ltd.

Copies of 12d View software must not be released to any party, or used for bureau applications without the
written permission of 12d Solutions Pty Ltd.

Copyright (c) 1989-2019 by 12d Solutions Pty Ltd

Sydney, New South Wales, Australia.
ACN 101 351 991
All rights reserved.

2
1 Preface ................................................................................................................................................. 3
1.1 Introduction ............................................................................................................................ 3
1.2 12d View Manual in PDF Form............................................................................................. 3
2 Installing and Registering 12d View ................................................................................................. 5
2.1 12d View - 64 bit or 32 bit Version ?..................................................................................... 6
2.2 Installing 12d View 14 from the Setup.Exe ........................................................................... 7
2.2.1 Folders Created by the Installation ........................................................................ 12
2.2.2 Icons Created by the Installation ........................................................................... 13
2.3 When Do You Need to Register 12d View? ........................................................................ 14
2.3.1 Registering 12d View ............................................................................................ 15
2.3.1.1 12d View Registration Panel17
2.3.2 Installing the Nodes.12d14dn file.......................................................................... 19
2.4 12d View Not Registering.................................................................................................... 22
2.4.1 Projects With Their Own Authorization Path........................................................ 22
2.4.2 Licence Expiry Warning ........................................................................................ 23
3 Starting Up ........................................................................................................................................ 25
3.1 Front Panel - Open a Recent Project .................................................................................... 26
3.2 Browse Button and Open Tab .............................................................................................. 28
3.3 Create Empty Project Button ............................................................................................... 30
4 Save and Exit..................................................................................................................................... 31
4.1 Save and Exit from Main Menu ........................................................................................... 32
4.2 Save/Exit from Floating12d View Menu ............................................................................. 32

1
12d View Reference Manual

2
1 Preface
1.1 Introduction
12d Model is an object oriented, interactive graphics program that processes survey data,
quickly builds terrain, concept and detailed design models. It is used in the construction of the
design, doing quality check and collecting as-constructed data.

That is, 12d Model is used in all stages of the civil planning, design and construction.

12d View is a freely available program to view projects created by 12d Model.
Extra data can also be read in and displayed from 12da and 12d XML files, ifc files, ADAC XML
files, DWG. DXF and DXB files, and genio files. But nothing can be saved from the 12d View
session and the project is left as it was before it was opened in 12d View.

12d View can also be used to create an empty project, and then to read data into the project to
examine and display. But nothing is saved at the end of the 12d View session.

This document is the 12d View Reference manual.

1.2 12d View Manual in PDF Form

12d View has a Help available from within 12d View for most panels and menus (context
sensitive Help).
The Help file is a pdf file, which can be read by pdf readers including the free Acrobat Reader.
The PDF file for the 12d View Reference manual is called
12d_view.pdf

Introduction Page 3
12d View Reference Manual

Page 4 12d View Manual in PDF Form

2 Installing and Registering 12d View
12d View 14 is installed from a setup.exe file which can be downloaded from the internet. See
2.2 Installing 12d View 14 from the Setup.Exe.
The installation loads the appropriate components and creates the 12d View 12 icon

icon for 12d View 64 bit exe icon for 12d View 32 bit exe

Clicking on the 12d View 14 - 32 or 12d View 14 - 64 icon fire up 12d View.

When 12d View starts up, it comes up in one of three modes:

(a) 12d View has access to the 12d Model dongle and associated nodes.4d file for either
12d Model 12 or 12d Model 14. Then no Registration is needed and the Client name used
in 12d View. comes from the nodes.4d file.
Note: if you are using a network dongle then 12d View does NOT take a license from the
12d network dongle.
OR
(b) If 12d View does NOT has access to a 12d Model dongle and associated nodes file, BUT
12d View has been Registered with 12d Solutions for the computer it is running on, then
12d View will start up and uses the Client name from the Registration.
A new Registration is required for each computer that 12d View is run on.
OR
(c) If 12d View does NOT has access to a 12d Model dongle and has NOT been Registered
with 12d Solutions for that computer, then when 12d View opens a project, a License
Expiry Warning panel comes up,

and the Client name at the top of the 12d View screen displays "Unregistered User of 12d
View"

In ALL three cases, 12d View then starts up and displays the Open a Recent Project panel. See
3.1 Front Panel - Open a Recent Project.

Extra Note for All Installations

A three-button mouse is essential for efficient use of 12d View.

Page 5
12d View

2.1 12d View - 64 bit or 32 bit Version ?

Microsoft has a 64 bit Windows and a 32 bit Windows operating system.
So when installing 12d View, you need to select either the 64 bit 12d installation or the 32 bit
installation.
In 64 bit Windows, Microsoft have allowed for both 32 bit and 64 bit versions of the same
software to coexist on the same computer, so you could install both the 32 bit and the 64 bit
version of 12d View

The 64 bit 12d View only runs on 64 bit Windows and supports any of the 12d Model projects.

The 32 bit 12d View runs on both 32-bit and 64 bit Windows and supports any of the 12d Model
projects up to point sizes of 5M.

So if you require 12d View for project larger than 5,000,000 points, then you must run 64 bit
12d View on 64 bit Windows.

Page 6 12d View - 64 bit or 32 bit Version ?

 Chapter 2 Installing and Registering 12d View

2.2 Installing 12d View 14 from the Setup.Exe

These notes are for installing 12d View 14 from the 12d View 14 setup.exe.

A. Disk Space required for installing 12d View 14

Approximately 2 Gigabytes of disc space will be required for the installation to succeed.
Your login must have Administrator privileges.

B. Using the email with the nodes.12d14n file attached to it

The 12d Model 14 nodes.12d14n file will normally be emailed to you.
During the installation of 12d Model 14, an association is created for files ending in .12d14n
so after the installation, opening the nodes.12d14n will automatically copy it to the required
area (normally C:\12d\14.00) and rename it to nodes.4d.
If you do not have the nodes.12d14n attached to an email but instead have it in a folder,
clicking on the nodes.12d14n file after installing 12d Model 14 will also automatically copy it
to the required area (normally C:\12d\14.00) and rename it to nodes.4d. Or if the
12d Model 14 icon is clicked on, the Project Selection panel will be brought up and clicking on
the Nodes button will allow the nodes.12d14n or nodes.4d file to be selected and then
processed.

C. Starting the Installation of 12d View 14

Double click on the 12d View 14 Setup.exe and the 12d View Installation program
automatically begins.
Depending on your permissions for the Windows operating system, you may be asked to allow
the Setup exe to run. If so, click on Run.

The 12d View 14 installation begins.

Installing 12d View 14 from the Setup.Exe Page 7

12d View

Note - the following screens are for the 64 bit install but the 32 bit install is identical except the
words 64 bit are replaced by 32 bit.

Welcome Welcome message

Select Next to continue with the installation

Software License Agreement 12D Solutions license agreement

If you agree with the License conditions, click on I have read and accept the terms of the
Software License Agreement.
Select Next to continue with the installation

Page 8 Installing 12d View 14 from the Setup.Exe

 Chapter 2 Installing and Registering 12d View

Installation Location

Continue with the default installation folder for the software:

for 64 bit version: c:\Program Files\12d\12dview\14.00
for 32 bit version: c:\Program Files (x86)\12d\12dview\14.00
or click on Browse to browse to another folder for the installation
Select Next to continue with the installation

User Area

Continue with the default folder for the User Area for the software:

Installing 12d View 14 from the Setup.Exe Page 9

12d View

c:\12d\14.00
or click on Browse to browse to another folder for the User Area.
Select Next to continue with the installation

Ready to Install

Select Install to begin the actual installation

The software will be copied and installed onto the computer.

Page 10 Installing 12d View 14 from the Setup.Exe

 Chapter 2 Installing and Registering 12d View

The Microsoft C++ Redistributables will be installed (32 and 64 for 64-bit install)

Setup Complete

End of installation. Select Finish to complete the installation

This completes the installation of the 12d View software.

The folders and icons that are created in the installation are given in the sections:
2.2.1 Folders Created by the Installation
2.2.2 Icons Created by the Installation

12d View will now run on the computer but without having access to either a 12d Model
hardware lock (usually a CodeMeter) and associated nodes.4d file, or this computer being
registered to run 12d View, 12d Model projects CAN be still be opened and viewed but the
Client name at the top of the 12d View screen will be "Unregistered User of 12d View" and a
License Expiry Warning will be displayed each time a project is opened. See 2.3 When Do You
Need to Register 12d View?.

Continue to 2.2.1 Folders Created by the Installation.

Installing 12d View 14 from the Setup.Exe Page 11

12d View

2.2.1 Folders Created by the Installation

(a) For 64 bit 12d View on Windows 64 bit operating systems:
The 12d View installation loads the 12d View software into the folder
C:\Program Files\12d\12dview\14.00
OR

(b) For 32 bit 12d View 32 bit (for points up to 5M) on Windows 64 bit operating systems:
The 12d View installation loads the 12d View software into the folder
C:\Program Files (x86)\12d\12dview\14.00
(c) For 32 bit 12d View on Windows 32 bit operating systems
The 12d View installation loads the 12d View software into the folder
C:\Program Files\12d\12dview\14.00
OR

12d View users normally only have read access to the Program Files and/or Program Files (x86)
areas.

12d View software area

under Program Files

If the folder

C:\12d\14.00

does not exist, the 12d View installation on either 32 bit or 64 bit WIndows, will create it and give
read/write access to the folder for the user.

The folder 12d\14.00 is the default folder where, after Registration of 12d View, the 12d View
authorization file nodes.4d file will be installed.

Page 12 Installing 12d View 14 from the Setup.Exe

 Chapter 2 Installing and Registering 12d View

2.2.2 Icons Created by the Installation

The installation loads the appropriate components and creates the 12d View 12 icon

icon for 12d View 64 bit exe icon for 12d View 32 bit exe

The 12d View 14 - 32 and 12d View 14 - 64 icons fire up 12d View and attach to the folder
12d\14.00.

Continue to 2.3 When Do You Need to Register 12d View?.

Installing 12d View 14 from the Setup.Exe Page 13

12d View

2.3 When Do You Need to Register 12d View?

When 12d View starts up, it comes up in one of three modes:
(a) 12d View is opening a 12d Model project and 12d View has access to the 12d Model
dongle and associated nodes.4d file for either 12d Model 12. or 12d Model 14.
For this case, 12d View does not have to be Registered.
The Client name from the nodes.4d file is then used in 12d View.
Note: if you are using a network dongle then 12d View does NOT take a license from the
12d network dongle.
OR
(b) If 12d View does not has access to a 12d Model dongle and associated nodes file, BUT
12d View has been Registered with 12d Solutions for the computer it is running on, then
12d View will start up and use the Client name from the Registration.
For this case, 12d View is already Registered for that computer.
OR
(c) If 12d View does NOT has access to a 12d Model dongle and has NOT been Registered
with 12d Solutions for that computer, then when 12d View opens a project, a License
Expiry Warning panel comes up,

and the Client name at the top of the 12d View screen displays "Unregistered User of 12d
View"

To continue using 12d View, simply click OK and 12d View will continue to run for that
session.
To remove the License Expiry Warning for this case you need to register 12d View with
12d Solutions for the computer that 12d View is being run on.
To register 12d View, see 2.3.1 Registering 12d View.

Page 14 When Do You Need to Register 12d View?

 Chapter 2 Installing and Registering 12d View

2.3.1 Registering 12d View

This section goes through how to Register 12d View from either the Front Panel that comes up
when you first start up 12d View, or from within 12d View once a project has been opened.
The installation of 12d View creates the 12d View icon:

icon for 12d View 64 bit exe icon for 12d View 32 bit exe

Fire up 12d View by double clicking on the appropriate 12d View 14 icon.
12d View will then start up and if it does NOT detect a 12d Model dongle and nodes.4d file in
C:\12d\12.00 or C:\12d\12.00, or no 12d View registration for that computer in the nodes.4d
file, then the Open/Create panel brought up will have a Register button on it.

Open/Create Panel with

no nodes.4d registration file

To register 12d View without opening any project, click on the Register button to bring up the
panel for registering12d View. See 2.3.1.1 12d View Registration Panel for further instructions on
how to register of 12d View

If you have opened a project with 12d View then you can Register 12d View from within the
open project. To do so, simply click on Help to bring up the Help menu and then select Register
12d View.

When Do You Need to Register 12d View? Page 15

12d View

The panel for registering 12d View will then be brought up. Go to 2.3.1.1 12d View Registration
Panel for further instructions on how to continue the registration of 12d View.

Page 16 When Do You Need to Register 12d View?

 Chapter 2 Installing and Registering 12d View

2.3.1.1 12d View Registration Panel

Clicking on either the Register button on the Front Screen, or select Registering 12d View from the
Help menu from within an opened project, will display the Register 12d View panel for entering
the information required for registering 12d View.

you must have Agree to terms ticked on

Fill in the information - all the fields in black type must be filled in - and tick on the Agree to terms
box.
Once the details are filled in, then
(a) click on the Register button to send the information to 12d Solutions Pty Ltd
A file called 12dview_request.zip with the registration information is created and if
successfully sent to 12d Solutions then a Registration sent message is written to the
message area of the panel.
On receiving your request, 12d Solutions sends an email back with an attachment called
nodes.12d12n. See 2.3.2 Installing the Nodes.12d14dn file for instructions on completing
the registration of 12d View.
However you can continue using 12d View without successfully completing the registration.
OR if it fails to send then
(b) click on the Email registration button and if an email system is detected (for example,
Outlook), an email is constructed with the 12dview_request.zip attached.

When Do You Need to Register 12d View? Page 17

12d View

Send the email to [email protected]

On receiving your request, 12d Solutions sends an email back with an attachment called
nodes.12d14n. See 2.3.2 Installing the Nodes.12d14dn file for instructions on completing
the registration of 12d View.
However you can continue using 12d View without successfully completing the registration.

OR if it fails to create an email then

(c) click on the Save to file button and a file called 12dview_request.zip with the registration
information is created on the desktop, and a message written to the panel message area
saying where it is.
In this case, please email the file 12dview_request.zip as an attachment to
[email protected]
On receiving your request, 12d Solutions sends an email back with an attachment called
nodes.12d14n. See 2.3.2 Installing the Nodes.12d14dn file for instructions on completing
the registration of 12d View.
However you can continue using 12d View without successfully completing the registration.

In all cases, your registration request is sent to 12d Solutions where it is processed and an
email with an attachment called nodes.12d14n sent to the email address given in the
Register 12d View form. What to do once you receive the email is described in 2.3.2 Installing the
Nodes.12d14dn file.

Important Note
The 12d View registration is only for the computer that the Registration was generated on.
It will not work for any other computer.

Page 18 When Do You Need to Register 12d View?

 Chapter 2 Installing and Registering 12d View

2.3.2 Installing the Nodes.12d14dn file

After your registration request has been received by 12d Solutions and processed, an email with
an attachment called nodes.12d14n is sent to the email address given in the Register 12d View
form.

Fred Bloggs

When you installed 12d View, a Windows file association was set up so that a nodes.12d14n file
is recognised by Windows it fires up the Install a 12d Model Nodes file program.
So in the email, double click on the file nodes.12d14n and the Opening Mail Attachment panel
comes up.

click on
Open

Clicking on Open and invokes the Windows association and so the Install a 12d Model Nodes
File panel appears (this is the same panel as used for 12d Model).

When run, the Install a 12d Model Nodes File panel option unpacks the node.12d14n file to obtain
a nodes.4d file and then copies the nodes.4d file to where 12d View will be able to use it.

When Do You Need to Register 12d View? Page 19

12d View

The choices for Operation are:

Prepend - if a nodes.4d file already exists, the information in the nodes.12d14n file is added
to the beginning of the existing nodes.4d file. A backup up copy of the existing nodes.4d
is created.
Replace - if a nodes.4d file already exists, it is replaced by a new nodes.4d file with the
information in the nodes.12d14n file in it. A backup up copy of the existing nodes.4d is
created.
Append - if a nodes.4d file already exists, the information in the nodes.12d14n file is added
to the end of the existing nodes file. A backup up copy of the existing nodes.4d is created.
Select Replace, Append or Prepend and then click Install.

The new/updated nodes.4d file is created in the Destination folder (default is C:\12d\14.00) and
if a nodes.4d file already existed, a backup copy of it is made.

Page 20 When Do You Need to Register 12d View?

 Chapter 2 Installing and Registering 12d View

Note - if you don’t have the file nodes.12d14n attached to an email but instead have the file in a
folder accessible from your computer, then you can do the following:
If there is a nodes.12d14n file, double click on that file and the Install a 12d Model Nodes File panel
should appear and you continue as per the instructions above.

This completes the 12d View registration process and you should now be able to view any
12d Model 14, and earlier, projects and it displays your registered Client name.

If 12d View did not install correctly and you still have a Client called "Unregistered User of 12d
View", contact your 12d Model Reseller.
However you can continue using 12d View without successfully completing the registration.

For information on opening and viewing existing 12d Model 14 projects using 12d View, see 3
Starting Up 12d View.

When Do You Need to Register 12d View? Page 21

12d View

2.4 12d View Not Registering

See
2.4.1 Projects With Their Own Authorization Path
2.4.2 Licence Expiry Warning

2.4.1 Projects With Their Own Authorization Path

It is possible to set up a project in 12d Model that uses a different path to obtain the authorization
file (nodes.4d) for that project.
If that is the case when 12d View opens such a project there may be no valid authorization for
12d Model or 12d View authorization in that nodes.4d file.

However even though there is no valid registration, you can continue using 12d View but the
Client will be "Unregistered User of 12d View" and the License Expiry Warning panel will appear
when you open the project.

Page 22 12d View Not Registering

 Chapter 2 Installing and Registering 12d View

2.4.2 Licence Expiry Warning

The nodes.4d file that controls 12d View, only validates 12d View to run for a certain period of
time.
If when running 12d View, the Licence Expiry Warning panel appears:

It simply means that the nodes.4d file needs to be updated which is done by doing another 12d
View Registration. See 2.3 When Do You Need to Register 12d View?.

However you can continue using 12d View but the Client will be "Unregistered User of 12d View"
and the License Expiry Warning panel will appear when you open projects.

Please contract your 12d Model Reseller if you are having any problems obtaining a new
12d View registration

12d View Not Registering Page 23

12d View

Page 24 12d View Not Registering

3 Starting Up
This chapter contains information about how to start 12d View.
See
3.1 Front Panel - Open a Recent Project
3.2 Browse Button and Open Tab
3.3 Create Empty Project Button

Page 25
12d View Reference Manual

3.1 Front Panel - Open a Recent Project

When 12d View is installed from the setup.exe, the 12d View 14 icon is created.

icon for 12d View 64 bit exe icon for 12d View 32 bit exe

The 12d View icon is a shortcut to start 12d View and then attach to the folder C:\12d\12.00.

Double clicking the 12d View icon starts 12d View and displays the Open a Recent Project panel.

path to folder containing description of Explore option that opens Explorer

project (working folder) highlighted project at the highlighted project working folder

double click on a project line

to open the project
recent projects list highlighted project
project
version

project name

remove project from list

refresh list of projects

open highlighted project

create an empty project Date the highlighted project

bring up browser to go to an existing project was last accessed by 12d Model

If this does not work, please contact your 12d View administrator to check the procedure to be
used on your system. For a detailed description on how to install 12d View, see 2.2 Installing 12d
View 14 from the Setup.Exe.

To select a project is the Recent projects list, simply double click on the entry in the list and
12d View will open the project up.
The description of the functions of the fields and buttons in the Open a Recent Project panel are:
Field Description Type Defaults Pop-Up

Page 26 Front Panel - Open a Recent Project

 Chapter 3 Starting Up

Recent projects list output recent projects

names and folders of project recently select. Single clicking on an entry in the list displays the projects
description in the Project description area. Double clicking on an entry in the list changes to this
project
Project description output
description of the project highlighted in the Recent projects list.

Advanced tick box

if ticked, environment configurations can be assigned to the project and extra panel fields are
displayed to allow for this.
If not ticked, no extra panel fields are displayed.
Full path output
name of the full path to the project.
Last accessed output
date that the project was last accessed.

The icon Remove from list - removes the project from the recent projects list
The icon Refresh list - refreshes the recent projects list

For the Browse button, go to 3.2 Browse Button and Open Tab
For the Create Empty Project button, go to 3.2 Browse Button and Open Tab

Front Panel - Open a Recent Project Page 27

12d View Reference Manual

3.2 Browse Button and Open Tab

Clicking on the Browse button brings up the Open tab that allows you to browse and open an
existing project. This is used when opening a project that is not in the Recent Projects list.
The Open button opens the project that has been browsed to.

Folder input current folder Microsoft browser

name of the folder to look for the project. This will become the working folder.
If the displayed folder does not contain the required project, clicking LB on the folder icon on the right
side of the field will bring up the Microsoft browser which is used to navigate to the folder containing
the required project.

Page 28 Browse Button and Open Tab

 Chapter 3 Starting Up

If the selected folder contains 12d Model projects, then a pop-up with a list of projects in the folder is
displayed in the Project name field and the required project can be selected from the list.

list of projects
in the folder

Project input none projects in folder

name of the project to become the working project.
Open button
after selecting this button, the working folder is changed to the folder specified in the folder field and
the selected project opened. If the project does not exist, and error message appears.
Create Empty Project button
after selecting this button, a temporary empty 12d Model project is create.
Data can be read into the project and displayed but nothing can be saved. See 3.3 Create Empty
Project Button.
Recent Projects button
takes you back to the original front screen. See 3.1 Front Panel - Open a Recent Project.
Quit button
exit 12d View.
Continue to 3.3 Create Empty Project Button or return to 3 Starting Up.

Browse Button and Open Tab Page 29

12d View Reference Manual

3.3 Create Empty Project Button

Clicking on the Create Empty Project button creates a temporary empty 12d Model project and
then opens the project.

Data can be read into the project and displayed but nothing can be saved.

To return to the beginning of this chapter, click on 3 Starting Up.

Page 30 Create Empty Project Button

4 Save and Exit
Important Note - Save Disabled
Although in 12d View 14 you can create new views, add and remove models from views, and
change view settings, the ability to save this modified view information is currently disabled.

Save and Exit are available from both the Main Menu under Project or on the floating 12d View
menu.

on Main menu floating 12d View menu

Page 31
12d View Reference Manual

4.1 Save and Exit from Main Menu

Important Note - Save Disabled
Although in 12d View 14 you can create new views, add and remove models from views, and
change view settings, the ability to save this modified view information is currently disabled.

Selecting Save from the Main Menu=>Projects menu simply saves information about views in the
project modified since the last save.
When Exit is selected from the bottom of the Main Menu=>Projects menu and a save is not
needed,12d View exits the project.
If Exit is selected from the bottom of the Main Menu=>Projects menu and a save is needed, then
the Save Project ? yes-no panel is placed on the screen.

If Yes is selected, then 12d View saves the project and exits.
If No is selected, then 12d View does not save the project and exits.
If Cancel is selected, then the Exit is aborted and 12d View stays in the project.

4.2 Save/Exit from Floating12d View Menu

Important Note - Save Disabled
Although in 12d View 14 you can create new views, add and remove models from views, and
change view settings, the ability to save this modified view information is currently disabled.

When Save is selected from the left hand side of the bottom of the 12d View menu (Save / Exit
menu option), all the information modified since the last save is written to disk.

When Exit is selected from the right hand side of the bottom of the 12d View menu (Save / Exit
menu option), an Exit 12d Model panel is fired up.

Page 32 Save and Exit from Main Menu

 Chapter 4 Save and Exit

Selecting No removes the yes-no pop-up and leaves the user in 12d View.
If Yes is selected and a modification to the project has been made since the last project save, a
Save Project panel is fired up.

If yes is selected, the project is saved and 12d View terminates.

If no is selected, the project is not saved and 12d View terminates.
If cancel is selected, the exit option is aborted and the user is left in 12d View.

Selecting No removes the yes-no pop-up and leaves the user in 12d View
If Yes is selected and a modification to the project has been made since the last project save, a
Save Project panel is fired up.

Save/Exit from Floating12d View Menu Page 33

12d View Reference Manual

Page 34 Save/Exit from Floating12d View Menu