Topic 2: Building Systems

TOPIC 2
Building Systems
A system can be defined as an assembly of interrelated or interdependent
parts forming a more complex and unified whole and serving a common purpose.
A building can be understood to be the physical embodiment of a number of
systems and subsystems that must necessarily be related, coordinated, and
integrated with each other as well as with the three-dimensional form and spatial
organization of the building as a whole.
TYPES OF BUILDING SYSTEMS
A. Structural Systems
 Foundation Systems
 Floor Systems
 Wall-Column Systems
 Roof Systems
B. Non- Structural Systems

 Enclosure and Protection
 Mechanical Systems
 Finishing Systems
 Fixtures and Furniture
FOUNDATION SYSTEMS
The foundation is the lowest division
of a building (its substructure) constructed
partly or wholly below the surface of the
ground. Its primary function is to support
and anchor the superstructure above and
transmit its loads safely into the earth.
Because it serves as a critical link in the
distribution and resolution of building loads,
the foundation system must be designed to
both accommodate the form and layout
of the superstructure above and respond to the varying conditions of soil, rock,
and water below.
Building System Design | Instructor: Engr. Novel Keith T. Solis 1

We can classify foundation systems into two broad categories—shallow
foundations and deep foundations.
1. Shallow Foundation
Shallow or spread foundations are employed when stable soil of
adequate bearing capacity occurs relatively near to the ground surface. They
are placed directly below the lowest part of a substructure and transfer
building loads directly to the supporting soil by vertical pressure.
2. Deep Foundation
Deep foundations are employed when the soil underlying a foundation
is unstable or of inadequate bearing capacity. They extend down through
unsuitable soil to transfer building loads to a more appropriate bearing stratum
of rock or dense sands and gravels well below the superstructure.

FLOOR SYSTEMS
Floor systems are the horizontal planes

that must support both live loads (people,
furnishings, and movable equipment) and
dead loads (the weight of the floor
construction itself).
Floor systems must transfer their loads
horizontally across space to either beams or
columns or to loadbearing walls. Rigid floor
planes can also be designed to serve as
horizontal diaphragms that act as thin, wide
beams in transferring lateral forces to shear
walls.
A floor system may be composed of a series of linear beams and joists
overlaid with a plane of sheathing or decking, or consist of a nearly homogeneous
slab of reinforced concrete. The depth of a floor system is directly related to the
size and proportion of the structural bays it must span and the strength of the
materials used. The size and placement of any cantilevers and openings within the
floor plane should also be considered in the layout of the structural supports for
the floor.

WALL COLUMN SYSTEMS
Walls are the vertical constructions of a

building that enclose, separate, and protect its
interior spaces, they may be loadbearing structures
of homogeneous or composite construction
designed to support imposed loads from floors and
roofs, or consist of a framework of columns and
beams with nonstructural panels attached to or
filling in between them. The pattern of these load
bearing walls and columns should be coordinated
with the layout of the interior spaces of a building.
Columns are rigid, relatively slender structural members designed primarily

to support axial compressive loads applied to the ends of the members. Relatively
shorty thick columns are subject to failure by crushing rather than by buckling.
Failure occurs when the direct stress from an axial load exceeds the compressive
strength of the material available in the cross section. An eccentric load, however,
can produce bending and result in an uneven stress distribution in the section.

ROOF SYSTEMS
The roof system functions as the primary sheltering element for the interior
spaces of a building. The form and slope of a roof must be compatible with the
type of roofing (shingles, tiles, or a continuous membrane) used to shed rainwater
and melting snow to a system of drains, gutters, and downspouts. The construction
of a roof should also control the passage of moisture vapor, the infiltration of air,
and the flow of heat and solar radiation. And depending on the type of
construction required by the building code, the roof structure and assembly may
have to resist the spread of fire.
NON-STRUCTURAL SYSTEMS
ENCLOSURE AND PROTECTION SYSTEMS

 Partition Walls
 Insulation
 Curtain Walls
 Openings
Partition Walls
A partition wall is a wall for the purpose of separating rooms, or dividing a
room. Partition walls are usually not load-bearing. Partition walls may be
constructed of steel panels, bricks or blocks from clay, terra-cotta or concrete,
reinforced, or hollow. Glass blocks may also be used. They may also be
constructed from sheet glass. Glass partition walls are a series of individual
toughened glass panels, which are suspended from or slide along a robust
aluminum ceiling track.

Insulation
Building insulation refers broadly to any object in a building used as
insulation for any purpose. While the majority of insulation in buildings is for thermal
purposes, the term also applies to moisture insulation, acoustic insulation, and fire
insulation. Often an insulation material will be chosen for its ability to perform
several of these functions at once.
Curtain Walls
A curtain wall system is an outer covering of a building in which the outer
walls are non-structural, but keep the weather out and the occupants in, therefore
it can be made of a lightweight material. When glass is used as the curtain wall, a
great advantage is that natural light can penetrate deeper within the building. A

curtain wall is designed to resist air and water infiltration, sway induced by wind
and seismic forces acting on the building, and its own dead load weight forces.
Curtain are designed to span multiple floors, and take into consideration design
requirements such as: thermal expansion and contraction; building sway and
movement; water diversion; and thermal efficiency.

Openings
A door is a moving structure used to block off, and allow access to, an
entrance to or within an enclosed space. Similar exterior structures are called
gates. Doors normally consist of a panel that swings on hinges or that slides or spins
inside of a space. A window is an opening in a wall, door, roof that allows the
passage of light and, if not closed or sealed, air and sound. Modern windows are
usually glazed or covered in some other transparent or translucent material.
Windows are held in place by frames. Many glazed windows may be opened, to
allow ventilation, or closed, to exclude inclement weather.
MECHANICAL SYSTEMS
 HVAC Systems
 Water Supply and Sanitation
 Electrical and Lighting Systems
 Mechanical Transportation Systems
HVAC Systems
Heating, ventilating, and air-conditioning systems condition the interior
spaces of a building for the environmental comfort of the occupants. A potable
water supply is essential for human consumption and sanitation. The efficient
disposal of fluid waste and organic matter is necessary in order to maintain sanitary
conditions within a building and in the surrounding area. Electrical systems furnish
light and heat fora building's occupants, and power to run its machines.

Water Supply and Sanitation
The water supply system provides potable water for human consumption
and sanitation, while, the sewage disposal system removes fluid waste and
organic matter from a building.
Water must be supplied to a building in the correct quantity and at the

proper flow rate pressure and temperature to satisfy the above requirements. For
human consumption, water must be potable and free of harmful bacteria. To
avoid the clogging or corrosion of pipes and equipment, water may have to be
treated for hardness or excessive acidity.
Electrical and Lighting Systems

The electrical system controls, meters, and protects the electric power
supply to a building, and distributes it in a safe manner for power, lighting, security,
and communication systems.
The primary purpose of a lighting system is to provide sufficient illumination

for the performance of visual tasks. Recommended levels of illumination for certain
tasks specify only the quantity of light to be supplied. How this amount of light is
supplied affects how a space is revealed or how an object is seen.

Mechanical Transportation Systems
The mechanical transportation of people and goods is an energy-using
service which needs the designer’s attention at the earliest stages of building
design. Standards of service rise with expectations of quality by the final user and
with the provision of access for disabled people. Building transportation systems
include: Elevators, Escalators & Travelators.
FINISHING SYSTEMS
 Flooring
 Wall Finishes
 Plaster Work
 Wall Paneling
 Wall Cladding
 Suspended Ceilings
Flooring
Floor Finishing (Flooring) is the general term for a permanent covering of a
floor. Materials almost always classified as floor covering include carpet, area rugs,
and resilient flooring such as linoleum or vinyl flooring. Materials commonly called
flooring include wood flooring, ceramic tile, stone, terrazzo, and various seamless
chemical floor coatings.

Wall Finishes
Plaster Work
Plaster is a building material used for

coating walls and ceilings. Plaster is
manufactured as a dry powder and is mixed
with water to form a paste when used. The
reaction with water liberates heat through
crystallization and the hydrated plaster then
hardens.
Wall Paneling
Paneling is a wall covering constructed

from rigid or semi-rigid components. These
are traditionally interlocking wood, but could
be plastic or other materials. Paneling was
developed in antiquity to make rooms in
stone buildings more comfortable. The panels
served to insulate the room from cold stone.
Wall Cladding
Wall cladding is a type of decorative

covering intended to make a wall look like it
is made of a different sort of material than it
actually is. Some of the most common
examples are on the outside of buildings, but
cladding can also be an artistic element in
interior decorating.

Suspended Ceilings
A Suspended ceiling is a secondary ceiling, hung below the main structural
ceiling. It may also be referred to as a drop ceiling or a false ceiling. Suspended
ceilings are staple of modern construction and architecture in both residential and
commercial applications. Suspended ceilings provide a concealed space for
mechanical ductwork, electrical conduit, and plumbing lines. Light fixtures,
sprinkler heads, fire detection devices, and sound systems can be recessed into
the ceiling plane. The ceiling can be fire-rated to provide fire protection for the
supporting floor and roof structure. Thus, the ceiling system is able to integrate the
functions of lighting, air distribution, acoustical control, and fire protection.
Fixtures and Furniture

Topic 2: Building Systems

Uploaded by

Copyright:

Available Formats

Topic 2: Building Systems

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Topic 2: Building Systems

Uploaded by

Copyright:

Available Formats

TOPIC 2

TYPES OF BUILDING SYSTEMS

B. Non- Structural Systems

Building System Design | Instructor: Engr. Novel Keith T. Solis 1

Building System Design | Instructor: Engr. Novel Keith T. Solis 2

Floor systems are the horizontal planes

Building System Design | Instructor: Engr. Novel Keith T. Solis 3

Walls are the vertical constructions of a

Columns are rigid, relatively slender structural members designed primarily

Building System Design | Instructor: Engr. Novel Keith T. Solis 4

ENCLOSURE AND PROTECTION SYSTEMS

Building System Design | Instructor: Engr. Novel Keith T. Solis 5

Building System Design | Instructor: Engr. Novel Keith T. Solis 6

Building System Design | Instructor: Engr. Novel Keith T. Solis 7

Building System Design | Instructor: Engr. Novel Keith T. Solis 8

Water must be supplied to a building in the correct quantity and at the

Electrical and Lighting Systems

The primary purpose of a lighting system is to provide sufficient illumination

Building System Design | Instructor: Engr. Novel Keith T. Solis 9

Building System Design | Instructor: Engr. Novel Keith T. Solis 10

Plaster is a building material used for

Paneling is a wall covering constructed

Wall cladding is a type of decorative

Building System Design | Instructor: Engr. Novel Keith T. Solis 11

Fixtures and Furniture

Building System Design | Instructor: Engr. Novel Keith T. Solis 12

You might also like