Scribd
Upload
704 views1 page

Error Code Error Cause Elimination E53: 50 650 69 0101E - REV A (GROVE RT-TM) .DOC / Rev. A / 2007-08-17 / RK

This service manual provides information on error codes, possible causes, and solutions for an iFLEX2 crane control system with iSCOUT expert compact. Common issues include incorrect setup, defective or disconnected sensors, invalid data files, and issues with the CAN bus data transfer. Solutions range from checking connections and setup, replacing sensors or central units, to updating software or crane data files.

Uploaded by

Saraiva Equipamentos
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
704 views1 page

Error Code Error Cause Elimination E53: 50 650 69 0101E - REV A (GROVE RT-TM) .DOC / Rev. A / 2007-08-17 / RK

This service manual provides information on error codes, possible causes, and solutions for an iFLEX2 crane control system with iSCOUT expert compact. Common issues include incorrect setup, defective or disconnected sensors, invalid data files, and issues with the CAN bus data transfer. Solutions range from checking connections and setup, replacing sensors or central units, to updating software or crane data files.

Uploaded by

Saraiva Equipamentos
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Service Manual iFLEX2 with iSCOUT expert compact

Error code Error Cause Elimination


Wrong setup of min. analog Analog input not supported Setup correct Flag in in DGA
E53 inputs length1, angle1, 6.i.2
pressure1
No valid data in the crane Restore or upload valid crane
Error in crane data file. data file during calibration. data file
E56
Flash-EPROM defective Replace central unit
Buffered data file does not Reset system
contain valid data.
E57 Error in buffered data file.
Flash-EPROM defective Replace central unit
CAN Bus cable between the Check the connection between
central unit and the sensor the central unit and the sensor
unit defective or not units
Error in the CAN bus data connected.
E61
transfer for all CAN units Can bus port in the central Replace the central unit
unit defective
Short circuit in a CAN Bus Replace Can Bus cable
cable
Cable between the central Check the cable to the sensor
unit and the sensor unit unit
defective.
Error in the can bus data
Can bus port in the central Replace the central unit
E62 transfer of the pressure unit defective
transducer sensor unit Can bus port in the sensor Replace the sensor unit
unit is defective
Sensor unit is defective Replace the sensor unit
Error in the can bus pressure The analog values of the Replace the sensor unit
E63 sensor unit are invalid
transducer sensor unit
Error in the can bus data See E62 See E62
E64 transfer of the length/angle
sensor unit
Error in the can bus See E63 See E63
E65
length/angle sensor unit
Error in the data of the digtal PDB variable invalid Change system software
E66 Change MENTOR
I/O MENTOR
Error in the can bus data PDB variable invalid Connect digtal I/O external CAN
E67 transfer of the digtal I/O module
external module
The selected rigging condition Select another rigging condition
is not contained in the crane
E84 Wrong rigging condition. data file. Check the programming in the
crane data file.
The computed radius is too Check the programming in the
Error in the radius
E85 small (negative deflection) crane data file.
determination
The operating mode on the Select operating mode without
Operating mode switchover with
E89 console has been switched load on the boom
load. over with the boom loaded.
LMI processing time limit Reset system
E98 LMI watchdog activated exceeded Connect PC terminal and watch
error messages
Short circuit in the A2B switch Replace A2B switch
Short circuit in the A2B switch
EAB circuit Short circuit in the cable to
(not with radio A2B) the A2B switch Replace cable to the A2B
switch

56 50 650 69 0101E_REV A (GROVE RT-TM).DOC / Rev. A / 2007-08-17 / rk.

You might also like