0% found this document useful (0 votes)
129 views54 pages

Networks 512 CA Test 2

This document contains a series of multiple choice questions related to computer networking concepts. There are over 50 questions that cover topics like network nodes, packet switching, collision domains, Ethernet standards, wireless networking protocols, IP addressing, and more. For each question there are 4 potential answer choices and an identified correct answer.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
129 views54 pages

Networks 512 CA Test 2

This document contains a series of multiple choice questions related to computer networking concepts. There are over 50 questions that cover topics like network nodes, packet switching, collision domains, Ethernet standards, wireless networking protocols, IP addressing, and more. For each question there are 4 potential answer choices and an identified correct answer.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 54

NETWORKS 512 CA TEST 2

In computer network nodes are


Select one:
a. the computer that routes the data
b. all of the option mentioned
c. the computer that originates the data
d. the computer that terminates the data
The correct answer is: all of the option mentioned

The Internet is an example of


Select one:
a. All of the option mention
b. Cell switched network
c. Packet switched network
d. circuit switched network
The correct answer is: Packet switched network

How devises in a collision domain have to listen when a single host talks?
Select one:
a. 1
b. All of the option mention
c. 3
d. 2
The correct answer is: All of the option mention

In 10Base2, maximum length of coaxial cable is


Select one:
a. 100 meter
b. 185 meter
c. 10 meter
d. 500 meter
The correct answer is: 185 meter

Bluetooth has used a sophisticated version of


Select one:
a. TDMA
b. CDMA
c. FSK
d. CSK
The correct answer is: FSK

A source address is always a


Select one:
a. Broadcast
b. None of the option mention
c. Unicast
d. Multicast
The correct answer is: Unicast

In standard Ethernet data are converted to a digital signal using the


Select one:
a. NRZ - I
b. Manchester Scheme
c. NRZ - L
d. NRZ Scheme
The correct answer is: Manchester Scheme
Specifications for a wireless LAN are called
Select one:
a. Project 802.3
b. Standard 802.3u
c. IEEE 802.11
d. Standard 802.3z
The correct answer is: IEEE 802.11

In Transmission Control Protocol (TCP), numbering starts with a


Select one:
a. generated number
b. randomly granted number
c. randomly generated node
d. randomly generated number
The correct answer is: randomly generated number

How is the decimal value 10 represented in binary?


Select one:
a. 1000
b. 1011
c. 1010
d. 1001
The correct answer is: 1010

Dard was adopted by the


Select one:
a. OSI
b. None of the option mention
c. ANSI
d. ISO
The correct answer is: ANSI

Which one of the following computer network is built on the top of another network?
Select one:
a. chief network
b. overlay network
c. prime network
d. prior network
The correct answer is: overlay network

Two devices are in network if


Select one:
a. none of the option mentioned
b. PIDs of the processes running of different devices are same
c. a process in one device is able to exchange information with a process in another
device
d. a process is running on both devices
The correct answer is: a process in one device is able to exchange information with a
process in another device.

High speed Ethernet works on


Select one:
a. none of the mention
b. coaxial cable
c. optical fiber
d. twisted pair cable
The correct answer is: optical fiber

Protocol Data Unit (PDU) is similar to


Select one:
a. DSAP
b. MAC
c. HDLC
d. LLC
The correct answer is: HDLC

How many wire pairs are used with half duplex?


Select one:
a. None of the option mention
b. 4
c. 1
d. 2
The correct answer is: 1

Minimum length of data in Ethernet frame is


Select one:
a. 46 Bytes
b. 1518 Bytes
c. 64 Bytes
d. 1500 Bytes
The correct answer is: 46 Bytes

A point-to-point protocol over Ethernet is a network protocol for


Select one:
a. encapsulating Ethernet frames inside PPP frames
b. for security of PPP frames
c. encapsulating PPP frames inside Ethernet frames
d. for security of Ethernet frames
The correct answer is: encapsulating PPP frames inside Ethernet frames

Slot time of 10-Mbps Ethernet is


Select one:
a. 15.2
b. 12.5
c. 5.12
d. 51.2
The correct answer is: 51.2

IEEE 802.11 have three types of


Select one:
a. frames
b. signals
c. fields
d. sequences
The correct answer is: frame

Fast Ethernet can transmit data at rate of


Select one:
a. 150 mbps
b. 100 mbps
c. 50 mbps
d. 200 mbps
The correct answer is: 100 mbps

ADSL is the abbreviation of


Select one:
a. Asymmetric Digital Subscriber Line
b. Asymmetric Digital System Line
c. Asymmetric Dual Subscriber Line
d. Asymmetric Dual System Line
The correct answer is: Asymmetric Digital Subscriber Line
MAC is the abbreviation for:
Select one:
a. Master access point control
b. Mobile access control
c. Media access control
d. Multimedia access control
The correct answer is: Media access control

In IEEE Project 802, Logic Link Control (LLC) is used to control and handle the
Select one:
a. flow
b. all of the option mention
c. errors
d. frames
The correct answer is: all of the option mention

By using fast Ethernet two stations are connected with


Select one:
a. Switch
b. Hub
c. point to point
d. Bridge
The correct answer is: point to point

Which transmission mode is used for data communication along telephone lines?
Select one:
a. Synchronous
b. Serial
c. Asynchronous
d. Parallel
The correct answer is: Serial

Slot time for gigabit Ethernet is


Select one:
a. 0.312
b. 0.512
c. 0.412
d. 0.612
The correct answer is: 0.512

Communication channel is shared by all the machines on the network in


Select one:
a. unicast network
b. broadcast network
c. none of the option mentioned
d. multicast network
The correct answer is: broadcast network

An Ethernet frame that is less than the IEEE 802.3 minimum length of 64 octets is called
Select one:
a. run frame
b. short frame
c. main frame
d. mini frame
The correct answer is: run frame

Maximum length of 1000BaseSX is


Select one:
a. 5000 m
b. 25 m
c. 100 m
d. 550 m
The correct answer is: 550 m

What is the purpose of using the routing protocol in this lab?


Select one:
a. Each server can choose a different path when the current path fails.
b. Each server saves the appropriate IP addresses in its ARP cache.
c. It has no purpose.
d. The network administrator does not have to configure static routes.
The correct answer is: Each server can choose a different path when the current path
fails.

Frame of Media Access Control (MAC) layer consists of


Select one:
a. 3 fields
b. 7 fields
c. 9 fields
d. 5 fields
The correct answer is: 9 fields

What is the minimum header size of an IP packet?


Select one:
a. 10 bytes
b. 20 bytes
c. 16 bytes
d. 32 bytes
The correct answer is: 20 bytes

1000Base-LX has used two wires for long wave are


Select one:
a. Coaxial Cable
b. STP Cable
c. UTP Cable
d. Fiber Optic
The correct answer is: Fiber Optic

Flag of Start frame diameter (SFD) is


Select one:
a. 10101011
b. 10010011
c. 11011011
d. 111000011
The correct answer is: 10101011

Access method used in point coordination function (PCF) MAC sub layer is
Select one:
a. piconet
b. handshaking period
c. extended service set
d. polling
The correct answer is: polling

DNS is the abbreviation of


Select one:
a. Dynamic Name System
b. Domain Network Service
c. Dynamic Network System
d. Domain Name System
The correct answer is: Domain Name System
Current version in frame control field is
Select one:
a. 1
b. 0
c. 3
d. 2
The correct answer is: 0

IPV4 Address is
Select one:
a. 16 bit
b. 32 bit
c. 64 bit
d. 8 bit
The correct answer is: 32 bit

UTP is commonly used in


Select one:
a. FTTP
b. HTTP
c. None of the option mentioned
d. DSL
The correct answer is: DSL

Fast Ethernet also called


Select one:
a. Standard 802.3u
b. Standard 802.3z
c. Standard 802.3s
d. Standard 802.3y
The correct answer is: Standard 802.3u

Term that is used to set standards to enable intercommunication among equipment from
a variety of manufacturers is
called
Select one:
a. Project 2088
b. Project 208
c. Project 802
d. Project 8802
The correct answer is: Project 802

In Media Access Control (MAC), data received from upper sub layer and passes them to
the
Select one:
a. Transport Layer
b. Network Layer
c. Physical layer
d. Data Link Layer
The correct answer is: Physical layer

Which of this is not a guided media?


Select one:
a. Wireless LAN
b. Coaxial cable
c. Fiber optical cable
d. Copper wire
The correct answer is: Wireless LAN

Maximum length of optical fiber in 10BaseF is


Select one:
a. 100 meter
b. 500 meter
c. 185 meters
d. 2000 meter
The correct answer is: 2000 meter

100BaseFX is used for encoding of


Select one:
a. 8B/6T
b. MLT-3
c. Manchester
d. NRZ - I
The correct answer is: NRZ – I

What device can you not use full-duplex communication with?


Select one:
a. Router
b. Host
c. Hub
d. Switch
The correct answer is: Hub

IEEE 802.11 Direct Sequence Spread Spectrum (DSSS) uses data rate of
Select one:
a. 5.5 and 11 Mbps
b. 1 and 2 Mbps
c. 2 and 54 Mbps
d. 6 to 54 Mbps
The correct answer is: 5.5 and 11 Mbps
Why IP Protocol is considered as unreliable?
Select one:
a. Packets may arrive out of order
b. All of the option mention
c. A packet may be lost
d. Duplicate packets may be generated
The correct answer is: All of the option mention

Distortion caused on telephone line by an adjacent one is called


Select one:
a. Inductive Disturbance
b. Cross Fire
c. Cross Talk
d. None of the option mentioned
The correct answer is: Cross Talk

Each channel in Bluetooth layer is of


Select one:
a. LL
b. L2
c. L3
d. LA
The correct answer is: LL

ISDN handles data pertaining to


Select one:
a. Speech and Video
b. Speech only
c. Computer data only
d. All digital services
The correct answer is: All digital services

In which of the following networking scenarios would a router be the optimal


connectivity device?
Select one:
a. A LAN that connects 10 users, a server, and a printer at a small business
b. A peer-to-peer LAN that connects eight users to provide a shared database
c. A home network with five users who want to share documents that are stored on one
of the five workstations
d. A WAN that connects a college physics department with a classroom in a high school
on the other side of town
The correct answer is: A WAN that connects a college physics department with a
classroom in a high school on the other
side of town

When a station is idle, it waits for period of time is called


Select one:
a. Request to sent
b. clear to send
c. Distributed Interframe Space
d. Short Interframe Space
The correct answer is: Distributed Interframe Space

What does the Tracert command show?


Select one:
a. The operating system runs by the host at the destination address
b. The path taken by packets to the destination address
c. The MAC address of the destination address
d. Whether the remote host supports TCP/IP
The correct answer is: The path taken by packets to the destination address
How many wire pairs are used with 100 BaseT full duplex?
Select one:
a. 1
b. 2
c. None of the option mention
d. 4
The correct answer is: 2

In full duplex mode of gigabit Ethernet, there is no


Select one:
a. Frame Bursting
b. attenuation
c. Collision
d. carrier extension
The correct answer is: Collision

Gigabit Ethernet has a data rate of


Select one:
a. 1500 Mbps
b. 1000 Mbps
c. 2000 Mbps
d. 100 Mbps
The correct answer is: 1000 Mbps

By using bridge, collision is


Select one:
a. Small
b. Large
c. Reduced
d. Increased
The correct answer is: Reduced

When connectivity devices are connected in a daisy-chain fashion, what type of


backbone do they create?
Select one:
a. Distributed
b. Serial
c. Collapsed
d. Parallel
The correct answer is: Serial

What does Router do in a network?


Select one:
a. Forwards a packet to all outgoing links except the originated link
b. Determines on which outing link a packet is to be forwarded
c. Forwards a packet to the next free outgoing link
d. Forwards a packet to all outgoing links
The correct answer is: Determines on which outing link a packet is to be forwarded

Which layers of the OSI model are host-to-host layers?


Select one:
a. Network, Transport, Session, Presentation
b. Physical, Datalink, Network, Transport
c. Transport, Session, Presentation, Application
d. Datalink, Network, Transport, Session
The correct answer is: Transport, Session, Presentation, Application

What is the meaning of Bandwidth in Network?


Select one:
a. Connected Computers in the Network
b. Transmission capacity of a communication channels
c. None of the option mention
d. Class of IP used in Network
The correct answer is: Transmission capacity of a communication channels

A large numbers of computers in a wide geographical area can be efficiently connected


using
Select one:
a. all of the option mention
b. Communication satellites
c. coaxial cables
d. twisted pair lines
The correct answer is: all of the option mention

Ethernet frame contains


Select one:
a. 7 Fields
b. 3 Fields
c. 9 Fields
d. 5 Fields
The correct answer is: 7 Fields

By using fast Ethernet two stations are connected with


Select one:
a. Hub
b. Switch
c. Bridge
d. point to point
The correct answer is: point to point

Which of the following devices only operates at the Physical layer of the OSI model?
Select one:
a. NIC
b. Bridge
c. Router
d. Hub or repeater
The correct answer is: Hub or repeater

Block encoding increases bit rate from


Select one:
a. 125 to 150 mbps
b. 150 to 175 mbps
c. 75 to 100 mbps
d. 100 to 125 mbps
The correct answer is: 100 to 125 mbps

In a time multiplexed space switching system, one speech sample appears every
Select one:
a. 125 msec
b. 1 sec
c. 125 micro sec
d. 20 msec
The correct answer is: 125 micro sec

ACL stands for


Select one:
a. Asynchronous Communicated Link
b. Asynchronous Connection Link
c. Asynchronous Connectionless Link
d. Asynchronous Connected Link
The correct answer is: Asynchronous Connectionless Link
What type of network access method is used on an Ethernet switch?
Select one:
a. Demand priority
b. Token passing
c. CSMA/CA
d. CSMA/CD
The correct answer is: CSMA/CD

Which of the following is true about the use of parallel backbones in real-life networks?
Select one:
a. Parallel backbones are used when redundant connections are not possible.
b. Parallel backbones are used whenever possible because they are so inexpensive.
c. Parallel backbones only work in Ethernet networks.
d. Parallel backbones are used for important servers and networks because they are more
expensive to build.
The correct answer is: Parallel backbones are used for important servers and networks
because they are more expensive to build.

A _____ is a device that forwards packets between networks by processing the routing
information included in the packet.
Select one:
a. router
b. all of the option mentioned
c. firewall
d. bridge
The correct answer is: router

If you are using a cable medium called 10Base, what does this mean?
Select one:
a. That you are running Ethernet over HDMI
b. That you are running Ethernet fiber
c. That you are bundling multiple connections
d. That you are really old and using thinnet coax for your LAN medium
The correct answer is: That you are really old and using thinnet coax for your LAN
medium

Media Access Control layer frame has


Select one:
a. 7 Fields
b. 5 Fields
c. 11 Fields
d. 9 Fields
The correct answer is: 9 Fields

Computer Society of IEEE started a project in


Select one:
a. 1975
b. 1985
c. 1980
d. 1970
The correct answer is: 1985

A list of protocols used by a system, one protocol per layer, is called


Select one:
a. protocol architecture
b. protocol suit
c. protocol stack
d. none of the mentioned
The correct answer is: protocol stack

By using bridge, collision is


Select one:
a. Increased
b. Large
c. Small
d. Reduced
The correct answer is: Reduced

The Internet is an example of


Select one:
a. Packet switched network
b. All of the option mention
c. Cell switched network
d. circuit switched network
The correct answer is: Packet switched network

In Transmission Control Protocol (TCP), numbering starts with a


Select one:
a. randomly granted number
b. randomly generated node
c. generated number
d. randomly generated number
The correct answer is: randomly generated number

Bluetooth defines several protocols for the


Select one:
a. Higher Layer
b. Upper Layer
c. Sub Layer
d. Lower Layer
The correct answer is: Upper Layer
Term in which a station can move from one basic service set to another is called
Select one:
a. BSS transition mobility
b. ESS transition mobility
c. No transition mobility
d. none of the option mention
The correct answer is: BSS transition mobility

Which of the following is correct regarding Class B Address of IP ADDRESS?


Select one:
a. Network bit – 12, Host bit – 14
b. Network bit – 18, Host bit – 16
c. Network bit – 14, Host bit – 16
d. Network bit – 16, Host bit – 14
The correct answer is: Network bit – 14, Host bit – 16

How many layers are in the TCP/IP model?


Select one:
a. 4 layers
b. 7 layers
c. 6 layers
d. 5 layers
The correct answer is: 4 layers

Bluetooth network consists of one primary device and up to


Select one:
a. 11 Devices
b. 5 Devices
c. 7 Devices
d. 9 Devices
The correct answer is: 7 Devices

Broad Band ISDN handles data rate of about


Select one:
a. 2.048 mbps
b. 100 mbps
c. 64 kbps
d. 5.4 mbps
The correct answer is: 64 kbps

What is the minimum header size of an IP packet?


Select one:
a. 20 bytes
b. 16 bytes
c. 32 bytes
d. 10 bytes
The correct answer is: 20 bytes

Maximum length of 10GBase-L is


Select one:
a. 40 km
b. 100 m
c. 300 m
d. 10 km
The correct answer is: 10 km

For which of the following network devices is redundancy least important?


Select one:
a. User workstations
b. A central switch
c. The network backbone cabling
d. Server
The correct answer is: User workstations

When might the best path not equal the shortest distance between two nodes? (Choose
all that apply.)
Select one:
a. When a communications link is suffering congestion
b. When the media on the shortest path is slower than the media on the best path
c. When a communications link has been recently added to the network
d. When a router experiences routing protocol errors
The correct answer is: When the media on the shortest path is slower than the media on
the best path

Preamble contains
Select one:
a. 6 Bytes
b. 4 Bytes
c. 1 Byte
d. 2 Bytes
The correct answer is: 1 Byte

Duration field D of Media Access Control layer frame contains


Select one:
a. 2bytes
b. 6 bytes
c. 4 bytes
d. 8 bytes
The correct answer is: 2bytes
In the default ping command on a computer running Windows, how many replies will
you receive if the test is successful?
Select one:
a. 4
b. 3
c. 2
d. 1
The correct answer is: 4

Value of frame body field of Media Access Control frame is in between


Select one:
a. 0 and 512 bytes
b. 0 and 1214 bytes
c. 0 to 2312 bytes
d. 0 to 3450 bytes
The correct answer is: 0 to 2312 bytes

In 10Base2, cable is
Select one:
a. Large
b. Thick
c. Thin
d. Small
The correct answer is: Thin

Flag of Start frame diameter (SFD) is


Select one:
a. 10010011
b. 10101011
c. 111000011
d. 11011011
The correct answer is: 10101011

Minimum length of data in Ethernet frame is


Select one:
a. 1518 Bytes
b. 46 Bytes
c. 64 Bytes
d. 1500 Bytes
The correct answer is: 46 Bytes

Which of the following can run full duplex and achieve 200 Mbps with Cat 5e cable?
Select one:
a. 1000BaseF
b. 100BaseTX
c. 100baseF
d. 1000BaseT
The correct answer is: 100BaseTX

Media Access Control layer frame has


Select one:
a. 5 Fields
b. 9 Fields
c. 11 Fields
d. 7 Fields
The correct answer is: 9 Fields

In full duplex mode of gigabit Ethernet, there is no


Select one:
a. attenuation
b. Collision
c. Frame Bursting
d. carrier extension
The correct answer is: Collision

What is the effective total throughput increase with a full-duplex connection?


Select one:
a. Twice as much
b. Four times as much
c. Ten times as much
d. None
The correct answer is: Twice as much

Fast Ethernet was designed to compete with


Select one:
a. MAN protocol
b. WAN protocol
c. LAN protocols
d. None
The correct answer is: LAN protocols

Acknowledgments of frames must be implemented at the


Select one:
a. Data Link Layers
b. Lower Layers
c. Higher Layers
d. Sub Layers
The correct answer is: Higher Layers

How devises in a collision domain have to listen when a single host talks?
Select one:
a. All of the option mention
b. 2
c. 3
d. 1
The correct answer is: All of the option mention

IEEE 802.11 have three types of


Select one:
a. sequences
b. fields
c. signals
d. frames
The correct answer is: frames

What menu option sequence would you choose to set up Routing and Remote Access
Service on a Windows Server 2012
computer?
Select one:
a. Start, Control Panel, Routing and Remote Access
b. Start, All Programs, Accessories, Routing and Remote Access
c. Start, Administrative Tools, Routing and Remote Access
d. Start, Control Panel, Network Connections, Routing and Remote Access
The correct answer is: Start, Administrative Tools, Routing and Remote Access

Primary and secondary devices communicate with each other using


Select one:
a. Time Slots
b. Data
c. Signals
d. Frames
The correct answer is: Time Slots
What is the address size of IPv6?
Select one:
a. 128 bit
b. 32 bit
c. 256 bit
d. 64 bit
The correct answer is: 128 bit

Round trip time and time required to send jam sequence is called the
Select one:
a. Propagation speed
b. Collision
c. Maximum length
d. slot time
The correct answer is: slot time

What does protocol define?


Select one:
a. Protocol defines what data is communicated.
b. Protocol defines when data is communicated.
c. Protocol defines how data is communicated.
d. All of the option mention
The correct answer is: All of the option mention

A Master group consists of


Select one:
a. 300 voice channels
b. 60 voice channels.
c. 24 voice channels
d. 12 voice channels.
The correct answer is: 300 voice channels
Telex is a
Select one:
a. Tele printer Service between various subscribers
b. Telephone Service between various subscribers
c. Television Service between various subscribers
d. Telegraph Service between various subscribers
The correct answer is: Tele printer Service between various subscribers

Which of the following is the most common frame type on modern Ethernet networks?
Select one:
a. Ethernet 802.2 (Raw)
b. Ethernet SNAP
c. Ethernet 902.3 (Novell proprietary)
d. Ethernet II (DIX)
The correct answer is: Ethernet II (DIX)

The bandwidth requirement of a telephone channel is


Select one:
a. 25 KHz
b. 15 KHz
c. 3 KHz
d. 5 KHz
The correct answer is: 3 KHz

What command would you use to add a node’s IP address, subnet mask, and network
location interface to a routing
table?
Select one:
a. route add
b. route open
c. add host
d. add node
The correct answer is: route add

Original Ethernet has gone through


Select one:
a. four generations
b. three generation
c. two generations
d. only one generation
The correct answer is: four generations

Logic Link Control provides one single data link control protocol for all IEEE
Select one:
a. Local Area Networks
b. Wireless Networks
c. Wide Area Networks
d. Metropolitan Area Networks
The correct answer is: Local Area Networks

How many wire pairs are used with half duplex?


Select one:
a. 4
b. 2
c. 1
d. None of the option mention
The correct answer is: 1

1000Base-LX has used two wires for long wave are


Select one:
a. Fiber Optic
b. STP Cable
c. UTP Cable
d. Coaxial Cable
The correct answer is: Fiber Optic

A _____ is a device that forwards packets between networks by processing the routing
information included in the packet.
Select one:
a. router
b. firewall
c. bridge
d. all of the option mentioned
The correct answer is: router

In IEEE Project 802, Logic Link Control (LLC) is used to control and handle the
Select one:
a. flow
b. all of the option mentioned
c. errors
d. frames
The correct answer is: all of the option mentioned

MAC address helps in


Select one:
a. mobile access control
b. master access point control
c. media access control
d. multimedia access control
The correct answer is: media access control

Mode of propagation of data in 10GBase-E is


Select one:
a. Double mode
b. None of given
c. Single mode
d. Multi-mode
The correct answer is: Single mode

Preamble is actually added at the


Select one:
a. Upper Layer
b. Higher Layer
c. Physical layer
d. Sub Layer
The correct answer is: Physical layer

In 10Base2, maximum length of coaxial cable is


Select one:
a. 500 meter
b. 10 meter
c. 185 meter
d. 100 meter
The correct answer is: 185 meter

What is the decimal value for the binary number 11101000?


Select one:
a. 224
b. 232
c. 194
d. 128
The correct answer is: 232
Frame of Media Access Control (MAC) layer consists of
Select one:
a. 7 fields
b. 3 fields
c. 9 fields
d. 5 fields
The correct answer is: 9 fields

A star connected intermediate exchange is known as a


Select one:
a. Tandem exchange
b. Hub exchange
c. Private branch exchange
d. Repeater exchange
The correct answer is: Hub exchange

DHCP is the abbreviation of


Select one:
a. Dynamic Hyper Configuration Protocol
b. Dynamic Hyper Control Protocol
c. Dynamic Host Control Protocol
d. Dynamic Host Configuration Protocol
The correct answer is: Dynamic Host Configuration Protocol

What is the decimal equivalent of this binary number:


11000000.10101000.00110000.11110000?
Select one:
a. 192.168.48.192
b. 192.168.64.224
c. 192.168.48.240
d. 192.168.32.248
The correct answer is: 192.168.48.240

Header plus trailer of Ethernet is


Select one:
a. 12 Bytes
b. 18 Bytes
c. 14 Bytes
d. 16 Bytes
The correct answer is: 18 Bytes

Maximum length of 1000BaseSX is


Select one:
a. 100 m
b. 25 m
c. 550 m
d. 5000 m
The correct answer is: 550 m

In wireless LAN, there are many hidden stations so we cannot detect the
Select one:
a. Frames
b. Data
c. Collision
d. Signal
The correct answer is: Collision

Three different encoding schemes are used for all three implementations in
Select one:
a. Gigabit Ethernet
b. fast Ethernet
c. 10 Gigabit Ethernet
d. Standard Ethernet
The correct answer is: fast Ethernet

Fast Ethernet has a data rate of


Select one:
a. 560 Mbps
b. 50 Mbps
c. 100 Mbps
d. 700 Mbps
The correct answer is: 100 Mbps

Access method used in point coordination function (PCF) MAC sub layer is
Select one:
a. piconet
b. handshaking period
c. polling
d. extended service set
The correct answer is: polling

You have configured a device that runs the OSPF routing protocol, but whose primary
purpose is to prevent unwanted Internet traffic from reaching your company’s LAN.
Which of the following is true about this device?
Select one:
a. It is a firewall because its primary purpose is to control traffic.
b. It is a router because it runs a routing protocol.
c. It is a firewall because it runs a routing protocol.
d. It is a router because its primary purpose is to control traffic.
The correct answer is: It is a firewall because its primary purpose is to control traffic.

Why IP Protocol is considered as unreliable?


Select one:
a. Packets may arrive out of order
b. Duplicate packets may be generated
c. A packet may be lost
d. All of the option mention
The correct answer is: All of the option mention

Specifications for a wireless LAN are called


Select one:
a. Project 802.3
b. Standard 802.3u
c. IEEE 802.11
d. Standard 802.3z
The correct answer is: IEEE 802.11

Maximum length of optical fiber in 10BaseF is


Select one:
a. 500 meter
b. 2000 meter
c. 185 meters
d. 100 meter
The correct answer is: 2000 meter

DCF stands for


Select one:
a. Direct Control Function
b. Distributed Coordination Function
c. Distributed Control Function
d. Direct Coordination Function
The correct answer is: Distributed Coordination Function
Field of Media Access Control frame that is used to alternate 1s and 0s is called
Select one:
a. SFD
b. source address
c. destination address
d. preamble
The correct answer is: preamble

DNS is the abbreviation of


Select one:
a. Dynamic Network System
b. Domain Name System
c. Domain Network Service
d. Dynamic Name System
The correct answer is: Domain Name System

Trunks are the lines that run between


Select one:
a. Switching stations.
b. Subscribers and exchange
c. Local area network.
d. Switching system and power plant
The correct answer is: Switching stations.

100BaseTX uses two pairs of


Select one:
a. None of the option mention
b. twisted pairs
c. coaxial cable
d. fiber optic
The correct answer is: twisted pairs

Process is a little more involved, if there is more than one secondary in


Select one:
a. Piconet
b. Infrastructure Net
c. Adhoc Network
d. Small Net
The correct answer is: Piconet

Term that is used to set standards to enable intercommunication among equipment from
a variety of manufacturers is
called
Select one:
a. Project 2088
b. Project 208
c. Project 802
d. Project 8802
The correct answer is: Project 802

Which of the following is true about the use of parallel backbones in real-life networks?
Select one:
a. Parallel backbones are used whenever possible because they are so inexpensive.
b. Parallel backbones are used when redundant connections are not possible.
c. Parallel backbones are used for important servers and networks because they are more
expensive to build.
d. Parallel backbones only work in Ethernet networks.
The correct answer is: Parallel backbones are used for important servers and networks
because they are more expensive to build.

Telephone companies normally provide a voltage of __________to power telephones.


Select one:
a. +24 volts DC
b. -48 volts DC.
c. +48 volts DC
d. -24 volts DC
The correct answer is: -48 volts DC

Data link layer in IEEE standard is divided into two sub layers of
Select one:
a. LAN and MAC
b. LLC and ANSI
c. LLC and MAC
d. MAC and ACKs
The correct answer is: LLC and MAC

What is the size of Network bits & Host bits of Class A of IP address?
Select one:
a. Network bits 8, Host bits 23
b. Network bits 8, Host bits 24
c. Network bits 7, Host bits 23
d. Network bits 7, Host bits 24
The correct answer is: Network bits 7, Host bits 24

In field control frames, there are four address in which address 1 is always address of
Select one:
a. Original source
b. Final destination
c. Previous device
d. Next device
The correct answer is: Next device
Each IP packet must contain
Select one:
a. Source and Destination address
b. Only Destination address
c. Only Source addresses
d. Source or Destination address
The correct answer is: Source and Destination address

In a time multiplexed space switching system, one speech sample appears every
Select one:
a. 125 msec
b. 20 msec
c. 125 micro sec
d. 1 sec
The correct answer is: 125 micro sec

MAC address is of
Select one:
a. 48 bits
b. 24 bits
c. 36 bits
d. 42 bits
The correct answer is: 48 bits

Header of baseband layer frame has three identical sections of


Select one:
a. 20 Bits
b. 18 Bits
c. 16 Bits
d. 12 Bits
The correct answer is: 18 Bits

Which of the following IP address class is Multicast?


Select one:
a. Class B
b. Class A
c. Class C
d. Class D
The correct answer is: Class D

IPV4 Address is
Select one:
a. 64 bit
b. 8 bit
c. 32 bit
d. 16 bit
The correct answer is: 32 bit

Latest Ethernet standard is Ten-Gigabit Ethernet operates at


Select one:
a. 6 Gbps
b. 10 Gbps
c. 8 Gbps
d. 2 Gbps
The correct answer is: 10 Gbps

What does the Tracert command show?


Select one:
a. Whether the remote host supports TCP/IP
b. The MAC address of the destination address
c. The operating system runs by the host at the destination address
d. The path taken by packets to the destination address
The correct answer is: The path taken by packets to the destination address

Field retry means retransmitted frame when its value is set to


Select one:
a. 0
b. infinity
c. 1
d. -1
The correct answer is: 1

Each channel in Bluetooth layer is of


Select one:
a. 1 MHz
b. 2 MHz
c. 3 MHz
d. 4 MHz
The correct answer is: 1 MHz

Point Coordination Function- Interframe space (PIFS) is shorter than the


Select one:
a. SIFS
b. DIFS
c. RTS
d. CTS
The correct answer is: DIFS

What is auto negotiation?


Select one:
a. a security algorithm
b. a procedure by which two connected devices choose common transmission
parameters
c. none of the mention
d. a routing algorithm
The correct answer is: a procedure by which two connected devices choose common
transmission parameters

Echo suppressor is detrimental to full duplex operation because


Select one:
a. It enables one of the two pairs in a four-wire trunk line when a signal is detected on
the other pair.
b. It disables one of the two pairs in a four-wire trunk line when a signal is detected on
the other pair.
c. It activates both the pairs of a four-wire trunk line.
d. It is independent of line conditions.
The correct answer is: It disables one of the two pairs in a four-wire trunk line when a
signal is detected on the other pair.

Block encoding increases bit rate from


Select one:
a. 125 to 150 mbps
b. 150 to 175 mbps
c. 100 to 125 mbps
d. 75 to 100 mbps
The correct answer is: 100 to 125 mbps

Maximum length of 100BaseTX is


Select one:
a. 400 meter
b. 300 meter
c. 100 meter
d. 200 meter
The correct answer is: 100 meter

What type of network access method is used on an Ethernet switch?


Select one:
a. Token passing
b. CSMA/CA
c. Demand priority
d. CSMA/CD
The correct answer is: CSMA/CD

How many bits are there in the Ethernet address?


Select one:
a. 32 bits
b. 64 bits
c. 48 bits
d. 16 bits
The correct answer is: 48 bits

Bluetooth is an example of
Select one:
a. virtual private network
b. local area network
c. none of the option mentioned
d. personal area network
The correct answer is: personal area network

What type of port connects one switch to another in a daisy-chain fashion?


Select one:
a. External port
b. Uplink port
c. Patch panel port
d. Output port
The correct answer is: Uplink port

Maximum length of Ethernet frame is


Select one:
a. 512 bits
b. 12144 Bits
c. 46 Bits
d. 56 Bits
The correct answer is: 12144 Bits

Address is unicast, if least significant bit of first byte is


Select one:
a. -1
b. 0
c. 1
d. infinity
The correct answer is: 0

UTP is commonly used in


Select one:
a. HTTP
b. None of the option mentioned
c. FTTP
d. DSL
The correct answer is: DSL

Which of the following layer of OSI model also called end-to-end layer?
Select one:
a. Presentation layer
b. Transport layer
c. Session layer
d. Network layer
The correct answer is: Transport layer

What is interframe gap?


Select one:
a. idle time between frame bits
b. none of the mention
c. idle time between frames
d. idle time between packets
The correct answer is: idle time between frames

Point Coordination Function (PCF) is implemented in an


Select one:
a. adhoc network
b. distributed network
c. infrastructure network
d. cellular network
The correct answer is: infrastructure network

Protocol Data Unit (PDU) is similar to


Select one:
a. DSAP
b. HDLC
c. LLC
d. MAC
The correct answer is: HDLC

How is the decimal value 10 represented in binary?


Select one:
a. 1010
b. 1011
c. 1000
d. 1001
The correct answer is: 1010

Mostly signal propagation speed is


Select one:
a. 2 X 10^6
b. 2 X 10^2
c. 2 X 10 ^4
d. 2 X 10^8
The correct answer is: 2 X 10^8

The ________is a circuit-switched network, while the ______is a packet-switched


network.
Select one:
a. Telephone, ATM
b. Satellite, Telephone
c. FDDI and SONET
d. SONET and FDDI
The correct answer is: Telephone, ATM

Computer Network is
Select one:
a. Collection of hardware components and computers
b. Sharing of resources and information
c. All of the option mention
d. Interconnected by communication channels
The correct answer is: All of the option mention
Computer Society of IEEE started a project in
Select one:
a. 1980
b. 1970
c. 1985
d. 1975
The correct answer is: 1985

Ethernet frame consists of


Select one:
a. IP address
b. MAC address and IP address
c. none of the mentioned
d. MAC address
The correct answer is: MAC address

In computer network nodes are


Select one:
a. the computer that terminates the data
b. all of the option mentioned
c. the computer that originates the data
d. the computer that routes the data
The correct answer is: all of the option mentioned

How many wire pairs are used with 100 BaseT full duplex?
Select one:
a. 1
b. 2
c. 4
d. None of the option mention
The correct answer is: 2

Common channel signaling______________


Select one:
a. Does not use the speech or data path for signaling.
b. Finds it difficult to handle signaling during speech.
c. Uses the speech or data path for signaling.
d. Needs no additional transmission facilities.
The correct answer is: Needs no additional transmission facilities.

Bluetooth allows station to define a quality of


Select one:
a. Service Level
b. Data Level
c. Frame Level
d. Time Level
The correct answer is: Service Level

ADSL is the abbreviation of


Select one:
a. Asymmetric Digital System Line
b. Asymmetric Digital Subscriber Line
c. Asymmetric Dual Subscriber Line
d. Asymmetric Dual System Line
The correct answer is: Asymmetric Digital Subscriber Line

When a station is idle, it waits for period of time is called


Select one:
a. Distributed Interframe Space
b. Request to sent
c. Short Interframe Space
d. clear to send
The correct answer is: Distributed Interframe Space

In 100BaseT4 total number of wires are


Select one:
a. 6
b. 8
c. 4
d. 2
The correct answer is: 4

Transmission Control Protocol (TCP), has same Checksum controlling like


Select one:
a. TCP/IP
b. IP
c. ICMP
d. UDP
The correct answer is: UDP

Media access control is sub layer of


Select one:
a. LLC
b. ANSI
c. IEEE
d. LLC and ANSI
The correct answer is: IEEE

A Bluetooth LAN is an
Select one:
a. Adhoc Signals
b. Adhoc Interface
c. Adhoc LAN
d. Adhoc Network
The correct answer is: Adhoc Network

Slot time of 10-Mbps Ethernet is


Select one:
a. 51.2
b. 5.12
c. 15.2
d. 12.5
The correct answer is: 51.2

In Media Access Control (MAC), data received from upper sub layer and passes them to
the
Select one:
a. Network Layer
b. Transport Layer
c. Data Link Layer
d. Physical layer
The correct answer is: Physical layer

In multicast relationship between sender and receiver is


Select one:
a. one to one
b. many to many
c. one to many
d. many to one
The correct answer is: one to many

Direct inward dialing is used as a feature in


Select one:
a. VPN.
b. PBX.
c. PSTN.
d. EPABX.
The correct answer is: EPABX.

Gigabit Ethernet is also known as the


Select one:
a. Standard 802.3z
b. Standard 802.3s
c. Standard 802.3u
d. Standard 802.3y
The correct answer is: Standard 802.3z

You might also like