WARRANTY

Bacharach, Inc. warrants to Buyer that at the

time of delivery this Product will be free from INSTRUCTION 0013-9008
defects in material and manu-facture and will DRAFTRITE
conform substantially to Bacharach, Inc.’s ap- Rev.4 - May 2010
plicable specifications. Bacharach’s liability and
Buyer’s remedy under this warranty are limited
to the repair or replacement, at Bacharach’s op-
tion, of this Product or parts thereof returned to
Seller at the factory of manu-facture and shown
to Bacharach, Inc.’s reasonable satisfaction to
have been defective; provided that written
notice of the defect shall have been given by
Buyer to Bacharach within one (1) year after the
date of delivery of this Product by Bacharach,
Inc. For full details concerning this warranty,
contact Bacharach, Inc. Bacharach, Inc.
621 Hunt Valley Circle, New Kensington, PA 15068
Phone 724-334-5000 - Fax 724-334-5001
Made in U.S.A. ® Registered Trademark

WARRANTY

Bacharach, Inc. warrants to Buyer that at the

time of delivery this Product will be free from INSTRUCTION 0013-9008
defects in material and manu-facture and will DRAFTRITE
conform substantially to Bacharach, Inc.’s ap- Rev. 4 - May 2010
plicable specifications. Bacharach’s liability and
Buyer’s remedy under this warranty are limited
to the repair or replacement, at Bacharach’s op-
tion, of this Product or parts thereof returned to
Seller at the factory of manu-facture and shown
to Bacharach, Inc.’s reasonable satisfaction to
have been defective; provided that written
notice of the defect shall have been given by
Buyer to Bacharach within one (1) year after the
date of delivery of this Product by Bacharach,
Inc. For full details concerning this warranty,
contact Bacharach, Inc. Bacharach, Inc.
621 Hunt Valley Circle, New Kensington, PA 15068
Phone 724-334-5000 - Fax 724-334-5001
Made in U.S.A. ® Registered Trademark
 between furnace and draft regulator; (b)
Correct Draft
overfire between combustion space and heat
All combustion equipment requires correct
exchanger. Locate draft hole in flue at least
draft for best performance. Specific draft
6" from draft regulator or damper toward
recommendation should be obtained from
furnace. Use awl with ¼" shank to form hole
manufacturer.
in flue or light sheet metal. Overfire measure-
ment may be made through bolt hole or air
louvre in door or through observation port, if IMPORTANT NOTE
necessary, drill a ¼" hole. In case of oversize Draftrite is furnished in two ranges for
open-ing, Draft Tube should protrude several measurement of updraft/downdraft of fuel
inches minimum beyond inside wall, if neces- burning equipment as follows:
sary extend Draft Tube (see above). 1. .10 inch water downdraft
to .14 inch water updraft.
Assembly Draft Measurement Maintenance 2. .05 inch water downdraft
Screw Draft Tube parts É& Êto-gether Operate burner for several minutes and Protect instrument from dirt, oil, and to .25 inch water updraft.
then screw them into back of Draftrite while continuing to operate insert about half lint. Do not oil. Keep gauge in case when Neither of the above models can be used to
Ë. When required, extend Draft Tube of Draft Tube into draft hole. Cover Zero not in use, and keep case free of lint locate Neutral Pressure Point as required in
with length of ¼" copper tubing. Total Check hole Ìwith finger, level Draftrite until or dirt. Clean Draft Tube occasionally "Requirements for Instal-lation and Adjust-
length of extended tube must not exceed (a) Draft Tube is horizon-tal and (b) pointer with pipe cleaner. Protect gauge against ment of Domestic Gas Conversion Burners"
12 inches. is in line with zero scale mark, uncover Zero excessive shock. Do not use as continu- (ANSI-Z21.8-1994).
Location For Checking Draft Check hole without disturbing position of ously indicating instrument. Draftrite is
Heating Equipment Manufacturer may Draftrite. Pointer instantly shows draft or designed for spot checking draft where
require draft measurement (a) in flue pressure reading. Use of the Draftrite is il- extreme portability is important.
lustrated on front page.

between furnace and draft regulator; (b)

Correct Draft
overfire between combustion space and heat
All combustion equipment requires correct
exchanger. Locate draft hole in flue at least
draft for best performance. Specific draft
6" from draft regulator or damper toward
recommendation should be obtained from
furnace. Use awl with ¼" shank to form hole
manufacturer.
in flue or light sheet metal. Overfire measure-
ment may be made through bolt hole or air
louvre in door or through observation port, if IMPORTANT NOTE
necessary, drill a ¼" hole. In case of oversize Draftrite is furnished in two ranges for
open-ing, Draft Tube should protrude several measurement of updraft/downdraft of fuel
inches minimum beyond inside wall, if neces- burning equipment as follows:
sary extend Draft Tube (see above). 1. .10 inch water downdraft
to .14 inch water updraft.
Assembly Draft Measurement Maintenance 2. .05 inch water downdraft
Screw Draft Tube parts É& Êto-gether Operate burner for several minutes and Protect instrument from dirt, oil, and to .25 inch water updraft.
then screw them into back of Draftrite while continuing to operate insert about half lint. Do not oil. Keep gauge in case when Neither of the above models can be used to
Ë. When required, extend Draft Tube of Draft Tube into draft hole. Cover Zero not in use, and keep case free of lint locate Neutral Pressure Point as required in
with length of ¼" copper tubing. Total Check hole Ìwith finger, level Draftrite until or dirt. Clean Draft Tube occasionally "Requirements for Instal-lation and Adjust-
length of extended tube must not exceed (a) Draft Tube is horizon-tal and (b) pointer with pipe cleaner. Protect gauge against ment of Domestic Gas Conversion Burners"
12 inches. is in line with zero scale mark, uncover Zero excessive shock. Do not use as continu- (ANSI-Z21.8-1994).
Location For Checking Draft Check hole without disturbing position of ously indicating instrument. Draftrite is
Heating Equipment Manufacturer may Draftrite. Pointer instantly shows draft or designed for spot checking draft where
require draft measurement (a) in flue pressure reading. Use of the Draftrite is il- extreme portability is important.
lustrated on front page.