Page 70

TUTORIAL: - 10

L E
TS
TOOL HOLDER
ST R P
FO M

EN
SA

LEARNING OUTCOMES: -
1. How to put circular pattern.
UD
2. Counter-sunk hole modification and placement.
3. Creating an angular reference plane.

© CENTENNIAL COLLEGE 2016 Computer Aided Engineering using Solidworks, By C. S. SIDHU

 Page 71

L E
TS
ST R P
FO M

EN
SA

UD

© CENTENNIAL COLLEGE 2016 Computer Aided Engineering using Solidworks, By C. S. SIDHU

 Page 72

L E
TS
ST R P
FO M

EN
SA

UD

© CENTENNIAL COLLEGE 2016 Computer Aided Engineering using Solidworks, By C. S. SIDHU

 Page 73

TUTORIAL-10 (TOOL HOLDER)

1. SKETCH AND PART FEATURE: -
2. Go to Sketch>Select ‘Front plane> Sketch the below profile.
Extrude it ‘0.5in’ in Make a reference plane
‘Z’ Direction. (One ‘6in’ apart front the inside
Direction only not face (shown in pink),
Select ‘Front Plane’ both sides) towards z-direction.
> Sketch a center

E
rectangle ‘2.5inx2in’
at origin.

TS
ST R P
STEP-1 STEP-2 STEP-3
FO M

EN
Sketch> Draw this profile Sketch> Draw this
on the plane created in profile on inside
‘Step-3’>Finish Sketch. face>Finish Sketch.
SA

UD
STEP-5 STEP-4

2. Select Sketch(Sketch4)
created in ‘Step-4.

3. Select Sketch(Sketch3)
created in ‘Step-5. FINISH.

1. Go to Features> Lofted
Boss/Base> Select
profiles one by one.
MAKE SURE GREEN DOTS
ARE ALLIGNED IN ONE LINE.

STEP-6 STEP-7

© CENTENNIAL COLLEGE 2016 Computer Aided Engineering using Solidworks, By C. S. SIDHU

 Page 74

Create a plane at an angle with a reference of an Using the angular

edge and ‘Front Plane’. reference plane created
in ‘Step-8’. Draw a
curve as shown in the
4. New angular reference figure> FINISH Sketch.
plane created. FINISH.

1. Select ‘Edge’.

E
2. Front plane.

3. Select Angle >

‘70deg’ about edge

TS
MAKE SURE CURVE
from front plane.
START FROM THE
LOWER VERTEX OF
THE WEB
STEP-8 STEP-9
ST R P
Select the plane made
in ‘Step-10’ > Sketch> Now create a PLANE
FO M
Draw the ‘T-profile’ as (‘Normal to the curve’

EN
shown in the figure. made in ‘Step-9’).

1. Select line.
SA

MAKE SURE THIS

LINE IS PARALLEL 2. Select end point.
PATH LINE. TO PATH LINE. FINISH.

Before drawing ‘T-profile’

UD
project the reference point
using ‘Convert entity’ option.

STEP-11 STEP-10

Go to Features> Sweep Boss/Base> Select ‘Profile’ then ‘Path’.

1. Select ‘Profile’ (Sketch13)

2. Select ‘Path’ (Sketch12).

FINISH.

STEP-12

© CENTENNIAL COLLEGE 2016 Computer Aided Engineering using Solidworks, By C. S. SIDHU

 Page 75
Go to sketch> select the ‘Top face’.
Now draw a circle of ‘1.375in’ diameter Extrude it ‘1in’
taking midpoint of the edge as center. downwards.
FINISH.

L E
TS
STEP-13 STEP-14
ST R P
FO M

EN
SA

Now sketch another circle ‘0.5in’ Select the top face of the boss
diameter on the bottom face and made in ‘Step-14’> Now sketch a
UD
at the center of the cavity made circle ‘1in’ diameter at the center
in ‘Step-15’ > Extrude-Cut of the boss> Extrude-Cut ‘0.250in’
‘Through-All’. FINISH STEP-15 downwards. FINISH.
STEP-16

Draw a circle of 1.750in’ on

the front face> Extrude-Cut
‘Through-All’. FINISH.

STEP-19

Extrude it ‘2in’ on
both sides (i.e.
’Mid-plane’ option
in Direction 1)
Select ‘RIGHT PLANE’> Sketch a
circle of ‘2.125in’ diameter taking
midpoint of the edge as center.

STEP-17 STEP-18

© CENTENNIAL COLLEGE 2016 Computer Aided Engineering using Solidworks, By C. S. SIDHU

 Page 76
Now select the front face>
Sketch> Draw the tooth profile as
Select sketch > Extrude
shown below.
it ‘2in’ towards boss.
FINISH.

L E
TS
STEP-20 STEP-21
ST R P
2. Select Circular
3. Angle of revolution face about which
‘3600’. ‘22’ Entities.
FO M
pattern will revolve.

EN
Equal spacing.

1. Go to Features>
Circular Pattern.
SA

4. Drop down the

feature tree.
UD
5. Select feature to
revolve. FINISH. STEP-22

1. Select this face> Sketch. 2. Sketch this profile.

3. Extrude-Cut ‘0.125in,
deep. FINISH.

STEP-23 STEP-24

© CENTENNIAL COLLEGE 2016 Computer Aided Engineering using Solidworks, By C. S. SIDHU

 Page 77

2. COUNTER SINK HOLE: -

Now Go to > Features> Hole Specifications

2. Taking origin as reference draw

a center rectangle (1.750in High x
1.250in Wide)> Right click on
rectangle make it construction

E
using this option active .

1. Go to ‘Positions’

TS
3. Then from sketch menu click
ST R P point put four points on all four
corners of the construction
rectangle.
FO M

EN
STEP-25
SA

4. After finishing above,

Go to ‘Type’ tab.
UD
5. Select ‘Countersink’.

6. ANSI Inch.

7. Select ‘Flat Head Screw (82)’

8. Change hole size to ‘#12’

9. Change end conditions

to ‘Up To Surface’
10. Select face where to
end the screw hole.
FINISH. STEP-26

© CENTENNIAL COLLEGE 2016 Computer Aided Engineering using Solidworks, By C. S. SIDHU