Scribd
Upload
234 views12 pages

Design of Two Way Slab Modified 2

This document summarizes the design of a two-way reinforced concrete slab with discontinuous sides. Key details include the slab dimensions, loads, reinforcement requirements, and checks for depth, shear capacity, deflection, and torsional reinforcement at corners. Reinforcement is specified for the top and bottom of the slab at supports and mid-spans to resist bending moments. Torsional reinforcement is also specified for corners with one or both sides discontinuous. All design checks related to capacity, bar sizes and spacing are reported to comply with code requirements.

Uploaded by

karthik_iit
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
234 views12 pages

Design of Two Way Slab Modified 2

This document summarizes the design of a two-way reinforced concrete slab with discontinuous sides. Key details include the slab dimensions, loads, reinforcement requirements, and checks for depth, shear capacity, deflection, and torsional reinforcement at corners. Reinforcement is specified for the top and bottom of the slab at supports and mid-spans to resist bending moments. Torsional reinforcement is also specified for corners with one or both sides discontinuous. All design checks related to capacity, bar sizes and spacing are reported to comply with code requirements.

Uploaded by

karthik_iit
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 12

Design of two way slab - Two adjacent sides discontinous

Lx 3.600 Loads (kN/m^2)


Ly 6.380 Dead Load 3.125
fck 30.000 Live Load 3.000
fy 500.000 Wall load 1.000
For Fe 500; Xu,max/d 0.460 Surcace Finish 0.130
Total Design Load 10.883
Effective Span 3.705
Ultimate Design
Moments & Shear Force (Table 26, IS 456-2000)
(Ly/Lx)1 (Ly/Lx) (Ly/Lx)2 Ultimate Moments
1.75 1.772 2
Short Span Moment Coefficients ; α1-x α-x α2-x
0.084 0.085 0.091 Mu,-x 12.641
α1+x α+x α2+x
0.063 0.064 0.069 Mu,+x 9.491
Long Span Moment Coefficients α-y α+y Mu,-y 7.021
0.047 0.035 Mu,+y 5.228

Maximum Shear Force 19.589 kN/m

Overall Depth 125.000


Assume Clear Cover 20.000
Effective Depth,d 105.000

Check for Depth( Cl 38.1 & ANNEX-G , IS 456)


Mu, lim 12641235.625
So, d= 56.159

Reinforcement Mu,x = ( 0.87*Ast*fy*d)*[1-{(Ast*fy)/b*d*fck)}]


Span Ast (mm2/m) Bar Dia & Spacing
Top at Support (Lx) 290.126 10 mm dia @ 200 c/c
Bottom at Mid-Span (Lx) 208.205 8 mm dia @ 200 c/c
Top at Support (Ly) 153.944 8 mm dia @ 250 c/c
Bottom at Mid-Span (Ly) 114.596 8 mm dia @ 300 c/c

Minimum Steel (Cl. 26.5.2.1)


Ast,min 126.000 8 mm dia @ 250 c/c Provided at edge strips (Annex D-1.7, IS 456)

Maximum Diameter allowed, Φmax (Cl. 26.5.2.2) 15.625 mm SAFE

Maximum Spacing of Bars ( Cl. 26.3.3(1))

Maximum Spacing of Main Bars lesser of (3*140) or 300 SAFE

Max. Spacing of Minimum Steel Bars lesser of (5*140) or 450 SAFE


Check for Shear (Cl. 40.2.1.1, IS 456)
k for D=125 1.300
Deisgn Shear Strength of M30 gradeConc. ,τc 0.290

Deisgn Shear Strength of Slab, τc 0.377 N/mm2


τc, max (M30)
Table 20, IS 456 gives 3.500 τv < τc < τc, max SAFE
Computed Shear Stress, τv 0.187
Check for Deflection(Cl. 23.2.1, IS 456)
fs 0.58*fy*(As,reqd/As,prov)
As, reqd 290.126 Pt 0.2763101436417
As,prov 314.000 Kt 1.4 from Fig.4, Modification
fs 267.950
(L/d), basic 26.000
(L/d), actual 34.286
(L/d), max 36.400 SAFE

Torsional Reinforcement Bars (Annex D IS 456)


Arequired Area of 8 mm bar Bars needed Bars Provided
At C1 ( corner discontinous on both sides) (D-1.8) 156.153 50.24 3.10814904485488 4.000
At C2 ( corner discontinous onone side) (D-1.9) 78.077 50.24 1.55407452242744 2.000

Corner Min. distance(D-1.8) Bar Dia & Spacing Bars along X&Y(top & bot)
C1 720 ;720 mm 8 mm dia @ 180 c/c 4;4
C2 720 ; 1440 mm 8 mm dia @ 180 c/c 2;4

DETAILING
TORSIONAL REINFORCEMENT AT CORNER C1
TORSIONAL REINFORCEMENT AT CORNER C2
Area of 10mm bar Bars needed
78.5 3.6958681634
50.24 4.1441987265
50.24 3.0641637524
50.24 2.2809680448

rips (Annex D-1.7, IS 456)


from Fig.4, Modification factor

Bars Provided

You might also like