Product Data Sheet

Hempadur Mastic
45881

Product characteristics VOC content mixed product

5% thinning, Limit value,

Legislation Value
Description by volume phase II (2010)ª
Hempadur Mastic 45881 is a two-component polyamide adduct cured,
high solids, high build epoxy paint. It forms a hard and tough coating, 218 g/L 250 g/L 500 g/L
EU
has good wetting properties. [1.82 lb/US gal] [2.09 lb/US gal] [4.17 lb/US gal]
Complies with EU Directive 2004/42/EC, The Paints Directive on the 218 g/L
limitation of volatile organic compounds: subcategory j. US (coatings) - -
[1.82 lb/US gal]

218 g/L
Recommended use US (regulatory) - -
[1.82 lb/US gal]
As a selfprimed, surface tolerant paint system or as an intermediate or
finishing coat in heavy duty paint systems where low VOC and high 218 g/L
film build are required. China - -
[1.82 lb/US gal]
For immersed areas Hempadur Mastic 45881 is only recommended
for minor repairs. According to specific legislation, see details in the Explanatory Notes available
Can be specified where extended recoating properties for at Hempel website, hempel.com or at your local Hempel website. VOC values
polyurethane topcoats are requested (typically travel coating). May be may vary with shade, please consult the Safety Data Sheet, section 9. ªEU
used directly on cured zinc silicate (Galvosil products) or spray- Directive 2004/42/CE.
metallized surfaces to minimize popping.
Handling
Service temperature: Handle with care. Before and during use, observe safety labels on
- Maximum, dry exposure only: 120°C [248°F]. packaging and paint containers and follow all local and national safety
regulations. Always consult Hempel’s Safety Data Sheet for this
product along with the Product Data Sheet.
Certificates / Approvals
- EC-type examined as a low flame spread material when used as For professional use only.
part of a predefined paint system. Please refer to “Declaration of
Conformity” on hempel.com for further details.
- Complies with US FDA and EU food regulations for contact with dry
foodstuff. Consult Hempel for details.
Product data
Product code
Product safety 45881

Flash point 39°C [102°F] Product components

Base 45889
Curing agent 95881
_______________________________
Standard shade* / code
Light grey 12170 **

Gloss
Semi-gloss

Volume solids
80 ± 2%

* Wide range of colours is available via Hempel’s Multi-Tint® system. Issued by Hempel A/S - June 2021
** Slight discolouration may occur. This does not affect the performance of the coating. 1/4
Product Data Sheet

Hempadur Mastic
45881

Specific gravity Roughness

1.5 kg/L [12 lb/US gal] - Surface profile Medium (G) (ISO 8503-2).

Reference dry film thickness Consult Hempel's separate Surface Preparation Guidelines for more
125 micron [4.9 mils] details.

_______________________________
Aluminium shade / code Application
Aluminium grey 19000 *

Mixing ratio
Gloss Base 45889 : Curing agent 95881
Please consult Hempel’s Guideline on aluminium pigmented coatings. (3 : 1 by volume)

Volume solids Stir well before use.

72 ± 2%
Thinner
Specific gravity Hempel's Thinner 08450
1.3 kg/L [11 lb/US gal]
Cleaner
Reference dry film thickness Hempel's Tool Cleaner 99610
125 micron [4.9 mils]
Pot life

Product 20°C 30°C

Surface preparation temperature [68°F] [86°F]

Pot life 2 hours 1½ hours

Cleanliness Pot life (spray) - 2 hours
- Remove oil, grease and other contaminants by suitable detergent
cleaning.
- Remove salts, detergents and other contaminants by high pressure Application method
fresh water cleaning.
Tool Application parameters
New build:
Nozzle pressure: 250 bar [3600 psi]
- Abrasive blasting to min. Sa 2½ (ISO 8501-1) / SP 10 (SSPC). Airless spray
Nozzle orifice: 0.017-0.023"
- Concrete: According to Hempel’s Specification.
- Remove dust, blast media and loose materials. Brush Not Applicable.

Roller Not Applicable.

Maintenance and Repair
- Spot abrasive blasting to min. PSa 2 (ISO 8501-2) / SP 6 (SSPC). If brush or roller application is used, more coats will be necessary to achieve
- Minor areas may be hand or power tool cleaned instead of abrasive the specified dry film thickness. Spray data are indicative and subject to
blasting. adjustment. Pressure is for a material temperature of 20°C [68°F].
- Water jetting to min. Wa 2 (ISO 8501-4).
- Flash rust degree of maximum FR M (ISO 8501-4).
- Remove dust, blast media and loose materials.

* Appearance of the aluminium pigmented coats will depend on application method, drying conditions, handling etc. Please see the Guideline on Issued by Hempel A/S - June 2021
Aluminium pigmented coatings at hempel.com or at your local Hempel website. 2/4
Product Data Sheet

Hempadur Mastic
45881

Film thickness Overcoating

Hempel’s specification supersedes any guidelines indicated in the overcoating
Specification range Low High Recommended table
100 micron 200 micron 125 micron
Dry film thickness 20°C 30°C 40°C
[3.9 mils] [7.9 mils] [4.9 mils] Quality name
[68°F] [86°F] [104°F]
125 micron 250 micron 150 micron
Wet film thickness Atmospheric medium
[5 mils] [10 mils] [6 mils]

8 m²/L 4 m²/L 6.4 m²/L Hempadur Mastic Min 7h 5½ h 3½ h

Theoretical spreading 45881 Max Ext* Ext Ext
[330 sq ft/US [160 sq ft/US [260 sq ft/US
rate
gal] gal] gal] Hempathane HS Min 6h 5h 3h
Product may be specified in another film thickness than indicated depending 55610 Max Ext* Ext Ext
on purpose and area of use. This will alter spreading rate, drying and curing Atmospheric severe
time and overcoating interval. For best performance, avoid excessive film
thickness. Hempadur Mastic Min 10 h 8h 5h
45881 Max Ext* Ext Ext

Application conditions Hempathane HS Min 10 h 8h 5h

- Temperature of product must be above 15°C [59°F] during 55610 Max 72 h 54 h 36 h
application.
- Surface temperature must be above 15°C [59°F] during application Overcoating times are indicative for products of the same generic chemistry.
and curing. Consult Hempel’s specification for more information.
- To avoid condensation, apply on a clean and dry surface with a
temperature that is at least 3°C [5°F] above the dew point. Drying conditions
- To obtain the drying time stated, it is important to maintain sufficient
Relative Humidity: ventilation during application, drying and curing.
- Relative humidity must be below 85% during drying and curing.
Overcoating details
- If the maximum overcoating interval is exceeded, roughening of the
surface is necessary to ensure intercoat adhesion.
Drying and overcoating - The surface must be dry and clean prior to application.

Other remarks
Product compatibility
- Epoxy coats have an inherent tendency of chalking in outdoor
- Previous coat: None or according to Hempel’s specification.
exposure. This does not affect the performance of the coating.
- Subsequent coat: None or according to Hempel’s specification. - Hempel’s Specification supersedes any recommendations given in
the Product Data Sheets.

Drying time

20°C
Surface temperature
[68°F]

Hard dry hours 3

Determined for dry film thickness 125 micron [4.9 mils] at standard conditions,
see Hempel’s Explanatory Notes for details.

Issued by Hempel A/S - June 2021

3/4
Product Data Sheet

Hempadur Mastic
45881

Storage
Shelf life

25°C 35°C
Ambient temperature
[77°F] [95°F]

Base 36 months 24 months

Curing agent 36 months 24 months

Shelf life from date of production, when stored in original, unopened

containers. Thereafter, the product quality must be re-inspected. Always check
the best before date or expiry date on the label.

Storage conditions
- Product must be stored according to local legislation, at 40°C
[104°F] without direct sunlight and protected from rain and snow.

Additional documents
Additional information is available at the Hempel website hempel.com
or at your local Hempel website:
- Explanatory Notes explaining the fields in this Product Data Sheet.
- Surface Preparation Guidelines.
- Application Guidelines for different application methods.
- General Application Guidelines

This Product Data Sheet (“PDS”) relates to the supplied product (“Product”) and is subject to updating from time-to-time. Accordingly, the buyer/applicator should have regard to the PDS supplied together
with the relevant batch of the Product (and not an earlier version). In addition to the PDS, the buyer/applicator may receive some or all of the following specifications, statements and/or guidelines as listed
below or as are available from the Hempel website under ‘Products’ at www.hempel.com (the “Additional documents”):
No. Document description Location/comments
1. Technical Statement One-off specific advice provided on request for specific projects
2. Specification Only issued for specific projects
3. PDS This document
4. Explanatory Notes to the PDS Available at www.hempel.com and contain relevant information about the Product testing parameters
5. Application Instruction Where available, at www.hempel.com
6. Generic technical guidelines (e.g. on application and surface preparation) Where available, at www.hempel.com

In the event of a conflict of information between the PDS and the Additional documents, the order of priority of information shall be in the order as set out above. In such event you should also contact your
representative at Hempel for clarification. Furthermore, the buyer/applicator must have full regard to the relevant Safety Data Sheet provided with each Product and which can also be downloaded from
www.hempel.com.
Hempel shall not be liable for defects where the application of the Product has not been made fully in accordance with the recommendations and requirements set out in the relevant PDS and the Additional
Documents. The information and terms of this disclaimer apply to this PDS, the Additional documents and any other documents supplied by Hempel in respect of the Product. In addition, the Product is
supplied and all technical assistance is given subject to Hempel’s General Conditions of Sale, Delivery and Service, unless otherwise expressly agreed in writing.

hempel.com Issued by Hempel A/S - June 2021

4/4