Scribd
Upload
325 views2 pages

Easydent4 Installation Guide For Vender and IT Consultants

Uploaded by

rlopez17296

The document outlines the two types of Easydent4 installations - server and workstation - and provides step-by-step instructions for installing each type; for server installations, all installation options should be selected, while for workstations, the two "server" options should be unchecked; workstations also require configuring the Net.ini file with the server IP address obtained during the server installation.

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt

Easydent4 Installation Guide For Vender and IT Consultants

Uploaded by

rlopez17296
325 views2 pages
The document outlines the two types of Easydent4 installations - server and workstation - and provides step-by-step instructions for installing each type; for server installations, all installation options should be selected, while for workstations, the two "server" options should be unchecked; workstations also require configuring the Net.ini file with the server IP address obtained during the server installation.

Original Description:

Easydent 4 vatech installation

Original Title

Easydent4 Installation Guide for Vender and IT Consultants

Copyright

© © All Rights Reserved

Available Formats

PDF, TXT or read online from Scribd

Did you find this document useful?

Is this content inappropriate?

The document outlines the two types of Easydent4 installations - server and workstation - and provides step-by-step instructions for installing each type; for server installations, all installation options should be selected, while for workstations, the two "server" options should be unchecked; workstations also require configuring the Net.ini file with the server IP address obtained during the server installation.

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
325 views2 pages

Easydent4 Installation Guide For Vender and IT Consultants

Uploaded by

rlopez17296
The document outlines the two types of Easydent4 installations - server and workstation - and provides step-by-step instructions for installing each type; for server installations, all installation options should be selected, while for workstations, the two "server" options should be unchecked; workstations also require configuring the Net.ini file with the server IP address obtained during the server installation.

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
You are on page 1/ 2

Easydent4 Installation Guide for Vender and IT Consultants

1. There are two types of installation; it is important to understand those two main types

A. “Server” – From factory is located on the Capture PC (or main insulation that hosts the
“DB/Fileserver” for Easydent4.
Note: This can be installed on any system but the two main locations is the “Capture pc” for dental xray device; or the main office
server. For storage on the server; simply follow the instructions specifically for server except do the installation on the server*

Notice: It is recommended that both the DB and Fileserver be installed on the same system or server*.

B. “Workstation” – Any remote viewing station ; any station which does not host the DB/Fileserver

2. The installation files should be either located on the CD provided with the Dental Xray Device; on the
capture pc or network share (if already copied or downloaded) or it can be downloaded from Vatech
America Dealer share FTP or by contacting a Support representative to share the link for download.

3. Run the Easydent4 installation file.

4. During setup read each step carefully you will hit next a couple of times; once you arrive at the “Select
options” section you will do as follows depending on the type of installation you are performing.

A. For Server- Select all options and proceed on ‘Next’ all the way through.

B. For workstation- uncheck the two items labeled with the word ‘server’. –Click next all the way
through.

5. For Server stations you are now finished if the system does not have a static IP please assign one and
write down for use on configuring workstations.

Note: For workstations continue one.

6. For workstations You will first need to know the IP as found on step 5.,

7. Open the following file location C:\Easydent4\

8. Open the “Net.ini” file; for some systems you might only see the name as “NET” and the description as
a “Configuration file; Open this file.
9. Using the IP address found or set during step 5; Edit the following 3 IP address lines.

[SERVERS]

DBSERVER_TYPE =IP

DBSERVER_IPADDR =127.0.0.1 Change

FILESERVER_IPADDR =127.0.0.1 Change

EZSYNCSERVER_IPADDR=127.0.0.1 Don’t change

[SQL_DBSERVER]

ID=sa

PWD=2002

DB=TSFD

DNS=127.0.0.1 Change

10. Save and Exit.

11. If you have any connection issues; verify that any Firewall or security software is allowing easydent4
through (Or you can turn off any such software) to allow the connection.

You might also like