www.aintech.

cl

Version 1.2
SAFETY DATA SHEET Revision Date 20/04/2020
According to Regulation (EC) No. 1907/2006 Generic EU MSDS

SECTION 1: Identification of the substance/mixture and of the company/undertaking

1.1 Product identifiers

Product name : AIRCOP

Product Number : AC20_01
Brand : AINTECH
REACH No. : A registration number is not available for this substance as the
substance or its uses are exempted from registration, the annual
tonnage does not require registration, or the registration is envisaged
for a later registration deadline.
CAS-No. : 67-63-0 (Isopropyl alcohol): 70%
: 7440-50-8 (copper powder): 60-100ppm
: 7732-18-5 (water): 30%

1.2 Relevant identified uses of the substance or mixture and uses advised against

Identified uses : Disinfection

1.3 Details of the supplier of the safety data sheet

Producer
Company : AINTECH SpA (RUC 76.951.378-7)
Address : Exequiel Fernandez 3397, Santiago, Macul, Chile
Telephone : +56 9 9015 9946

Distributor
Company : GLOBUZ bv (BE0817.220.050) - Commercial name: Nanometals
Address : Heidebergen 37 – 9830 Sint-Martens-Latem - België
Telephone : +32 9 221 00 69

1.4 Emergency telephone number

070 245245 (Anti-poison centre)

0477 22 39 60 (GLOBUZ bv – EU distributor)

*GLOBUZ bv – Heidebergen 37 – 9830 Sint-Martens-Latem - Belgium

 www.aintech.cl

SECTION 2: Hazards identification

2.1 Classification of the substance or mixture

Classification according to Regulation (EC) No 1272/2008

Flammable liquids (Category 2), H225

Eye irritation (Category 2), H319
Short-term (acute) aquatic hazard (Category 1), H400
For the full text of the H-Statements mentioned in this Section, see Section 16.

2.2 Label elements

Labelling according Regulation (EC) No 1272/2008

Pictogram

Signal word Danger

Hazard statement(s)

H225 Highly flammable liquid and vapour.

H319 Causes serious eye irritation.
H400 Very toxic to aquatic life.

Precautionary statement(s)
P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition
sources. No smoking.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P273 Avoid release to the environment.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes.
Remove contact lenses, if present and easy to do. Continue rinsing.

Supplemental Hazard Statements none

2.3 Other hazards

This substance/mixture contains no components considered to be either persistent, bioaccumulative

and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher.

*GLOBUZ bv – Heidebergen 37 – 9830 Sint-Martens-Latem - Belgium

 www.aintech.cl

SECTION 3: Composition/information on ingredients

3.1 Substances

Synonyms : Isopropanol
2-Propanol solution
IPA
Isopropyl alcohol
Formula : C3H8O
Molecular weight : 60,1 g/mol
CAS-No. : 67-63-0
EC-No. : 200-661-7

Component Classification Concentration

2-Propanol
Flam. Liq. 2; Eye Irrit. 2; STOT SE 3; H225, H319, 70 %
Concentration limits:
>= 20 %: STOT SE 3, H336;
For the full text of the H-Statements mentioned in this Section, see Section 16.

Formula : Cu
Molecular weight : 63,55 g/mol
CAS-No. : 7440-50-8
EC-No. : 231-159-6

Component Classification Concentration

Copper
Aquatic Acute 1; H400 60-100 ppm
M-Factor - Aquatic Acute: 10

For the full text of the H-Statements mentioned in this Section, see Section 16.

Component : Water
Concentration : 30%
Formula : H2O
Molecular weight : 18,02 g/mol
CAS-No. : 7732-18-5
EG-No. : 231-791-2
Unnecessary to show specific composition as a result of applicable regulations

SECTION 4: First aid measures

4.1 Description of first aid measures

General advice
Consult a physician. Show this safety data sheet to the doctor in attendance.
3

*GLOBUZ bv – Heidebergen 37 – 9830 Sint-Martens-Latem - Belgium

 www.aintech.cl

If inhaled
If breathed in, move person into fresh air. If not breathing, give artificial respiration. Consult a
physician.

In case of skin contact

Wash off with soap and plenty of water. Consult a physician.

In case of eye contact

Rinse thoroughly with plenty of water for at least 15 minutes and consult a physician.

If swallowed
Do NOT induce vomiting. Never give anything by mouth to an unconscious person. Rinse mouth with
water. Consult a physician.

4.2 Most important symptoms and effects, both acute and delayed

The most important known symptoms and effects are described in the labelling (see section 2.2)
and/or in section 11

4.3 Indication of any immediate medical attention and special treatment needed

No data available

SECTION 5: Firefighting measures

5.1 Extinguishing media

Suitable extinguishing media: Dry powder Dry sand

Unsuitable extinguishing media: Do NOT use water jet.

5.2 Special hazards arising from the substance or mixture

Copper oxides Carbon oxides

5.3 Advice for firefighters

Wear self-contained breathing apparatus for firefighting if necessary.

5.4 Further information

Use water spray to cool unopened containers.

*GLOBUZ bv – Heidebergen 37 – 9830 Sint-Martens-Latem - Belgium

 www.aintech.cl

SECTION 6: Accidental release measures

6.1 Personal precautions, protective equipment and emergency procedures

Use personal protective equipment. Avoid breathing vapours, mist or gas. Ensure adequate
ventilation. Remove all sources of ignition. Evacuate personnel to safe areas. Beware of vapours
accumulating to form explosive concentrations. Vapours can accumulate in low areas.
For personal protection see section 8.

6.2 Environmental precautions

Prevent further leakage or spillage if safe to do so. Do not let product enter drains. Discharge into the
environment must be avoided.

6.3 Methods and materials for containment and cleaning up

Contain spillage, and then collect with non-combustible absorbent material (e.g. sand, earth,
diatomaceous earth, vermiculite) and place in container for disposal according to local / national
regulations (see section 13).

6.4 Reference to other sections

For disposal see section 13.

SECTION 7: Handling and storage

7.1 Precautions for safe handling

Avoid contact with skin and eyes. Avoid inhalation of vapour or mist.
Keep away from sources of ignition - No smoking.Take measures to prevent the build-up of
electrostatic charge.
For precautions, see section 2.2.

7.2 Conditions for safe storage, including any incompatibilities

Store in cool place. Keep container tightly closed in a dry and well-ventilated place. Containers which
are opened must be carefully resealed and kept upright to prevent leakage.

7.3 Specific end use(s)

Apart from the uses mentioned in section 1.2 no other specific uses are stipulated

SECTION 8: Exposure controls/personal protection

8.1 Control parameters

Components with workplace control parameters

*GLOBUZ bv – Heidebergen 37 – 9830 Sint-Martens-Latem - Belgium

 www.aintech.cl

8.2 Exposure controls

Appropriate engineering controls

Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks
and at the end of the workday.

Personal protective equipment

Eye/face protection
Face shield and safety glasses. Use equipment for eye protection tested and approved under
appropriate government standards such as NIOSH (US) or EN 166(EU).

Skin protection
Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique
(without touching glove's outer surface) to avoid skin contact with this product. Dispose of
contaminated gloves after use in accordance with applicable laws and good laboratory practices.
Wash and dry hands.
The selected protective gloves have to satisfy the specifications of Regulation (EU) 2016/425 and the
standard EN 374 derived from it.

Splash contact
Material: Nitrile rubber
Minimum layer thickness: 0,11 mm
Break through time: 33 min
Material tested:Dermatril® (KCL 740 / Aldrich Z677272, Size M)
data source: KCL GmbH, D-36124 Eichenzell, phone +49 (0)6659 87300, e-mail [email protected], test
method: EN374

If used in solution, or mixed with other substances, and under conditions which differ from EN 374,
contact the supplier of the CE approved gloves. This recommendation is advisory only and must be
evaluated by an industrial hygienist and safety officer familiar with the specific situation of anticipated
use by our customers. It should not be construed as offering an approval for any specific use scenario.

Body Protection
Impervious clothing Flame retardant antistatic protective clothing. The type of protective equipment
must be selected according to the concentration and amount of the dangerous substance at the
specific workplace.

Respiratory protection
Where risk assessment shows air-purifying respirators are appropriate use a full- face particle
respirator type N100 (US) or type P3 (EN 143) respirator cartridges as a backup to engineering
controls. If the respirator is the sole means of protection, use a full-face supplied air respirator. Use
respirators and components tested and approved under appropriate government standards such as
NIOSH (US) or CEN (EU).

*GLOBUZ bv – Heidebergen 37 – 9830 Sint-Martens-Latem - Belgium

 www.aintech.cl

Control of environmental exposure

Prevent further leakage or spillage if safe to do so. Do not let product enter drains. Discharge into the
environment must be avoided.

SECTION 9: Physical and chemical properties

9.1 Information on basic physical and chemical properties

a) Appearance Form: liquid

Color: colorless
b) Odor Ethanol-acetone
c) Odor Threshold No data available
d) pH 7
e) Melting point/ Melting point/range: -85 - -80 °C
freezing point
f) Initial boiling point and 80.9 – 83.2°C
boiling range
g) Flash point 22°C – closed cup
h) Evaporation rate No data available
i) Flammability (solid, gas) The substance or mixture is flammable with the
category 1.
j) Upper/lower flammability or No data available
explosive limits
k) Vapour pressure 44 hPa
l) Vapour density No data available
m) Relative density 0,858 g/cm3
n) Water solubility No data available
o) Partition coefficient: No data available
n-octanol/water
p) Auto-ignition temperature No data available
q) Decomposition temperature No data available
r) Viscosity 2,08 cP
s) Explosive properties No data available
t) Oxidizing properties No data available

9.2 Other safety information

No data available

SECTION 10: Stability and reactivity

10.1 Reactivity
No data available

10.2 Chemical stability

Reacts with air to form peroxides.
Stable under recommended storage conditions.

*GLOBUZ bv – Heidebergen 37 – 9830 Sint-Martens-Latem - Belgium

 www.aintech.cl

10.3 Possibility of hazardous reactions

No data available

10.4 Conditions to avoid

Heat, flames and sparks.

10.5 Incompatible materials

Aluminium, Strong acids, Strong oxidizing agents, Acid chlorides, Halogen, Acid anhydrides

10.6 Hazardous decomposition products

Hazardous decomposition products formed under fire conditions. - Copper oxides Other
decomposition products - No data available
In the event of fire: see section 5

SECTION 11: Toxicological Information

11.1 Information on toxicological effects

Acute toxicity
No data available

Skin corrosion/irritation
No data available.

Serious eye damage/eye irritation

May irritate eyes.

Respiratory or skin sensitisation

No data available

Germ cell mutagenicity

No data available

Carcinogenicity
IARC: No component of this product present at levels greater than or equal to 0.1% is identified as
probable, possible or confirmed human carcinogen by IARC.

Reproductive toxicity
No data available

Specific target organ toxicity - single exposure

May cause respiratory irritation.

Specific target organ toxicity - repeated exposure

No data available

*GLOBUZ bv – Heidebergen 37 – 9830 Sint-Martens-Latem - Belgium

 www.aintech.cl

Aspiration hazard
No data available

Additional Information
RTECS: GL5325000
Symptoms of systemic copper poisoning may include: capillary damage, headache, cold sweat, weak
pulse, and kidney and liver damage, central nervous system excitation followed by depression,
jaundice, convulsions, paralysis, and coma. Death may occur from shock or renal failure. Chronic
copper poisoning is typified by hepatic cirrhosis, brain damage and demyelination, kidney defects, and
copper deposition in the cornea as exemplified by humans with Wilson's disease. It has also been
reported that copper poisoning has led to hemolytic anemia and accelerates arteriosclerosis., Damage
to the lungs., Vomiting, Diarrhea, Abdominal pain, Blood disorders

To the best of our knowledge, the chemical, physical, and toxicological properties have not been
thoroughly investigated.
Liver - Irregularities - Based on Human Evidence

SECTION 12: Ecological information

12.1 Toxicity
Copper: Toxicity to fish: mortality LOEC - Oncorhynchus mykiss (rainbow trout) - 0,022 mg/l - 96 h
Toxicity to daphnia and other aquatic invertebrates: EC50 - Daphnia magna (Water flea) - 0,04 - 0,05
mg/l - 48 h Remarks: (ECOTOX Database)

12.2 Persistence and degradability

No data vailable

12.3 Bioaccumulative potential

Bioaccumulation: Cyprinus carpio (Carp) - 40 d - 200 mg/l(Copper)
Bioconcentration factor (BCF): 108
12.4 Mobility in soil
No data available

12.5 Results of PBT and vPvB assessment

This substance/mixture contains no components considered to be either persistent, bioaccumulative
and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher.

12.6 Other adverse effects

Very toxic to aquatic life.
Avoid release to the environment.

*GLOBUZ bv – Heidebergen 37 – 9830 Sint-Martens-Latem - Belgium

 www.aintech.cl

SECTION 13: Disposal considerations

13.1 Waste treatment methods

Product
Offer surplus and non-recyclable solutions to a licensed disposal company. Waste material must be
disposed of in accordance with the Directive on waste 2008/98/EC as well as other national and local
regulations. Leave chemicals in original containers. No mixing with other waste. Handle uncleaned
containers like the product itself.

Contaminated packaging
Dispose of as unused product.

SECTION 14: Transport information

14.1 UN number

ADR/RID: 1219 / 3089 IMDG: 1219 / 3089 IATA: 1219 / 3089

14.2 UN proper shipping name

ADR/RID: METAL POWDER, FLAMMABLE, N.O.S. (Copper)

ISOPROPANOL

IMDG: METAL POWDER, FLAMMABLE, N.O.S. (Copper)

ISOPROPANOL

IATA: Metal powder, flammable, n.o.s.

Isopropanol

14.3 Transport hazard class(es)

ADR/RID: 4.1 IMDG: 4.1 IATA: 4.1

14.4 Packaging group

ADR/RID: II IMDG: II IATA: II

14.5 Environmental hazards

ADR/RID: yes IMDG Marine pollutant: yes IATA: No

14.6 Special precautions for user

No data available

10

*GLOBUZ bv – Heidebergen 37 – 9830 Sint-Martens-Latem - Belgium

 www.aintech.cl

SECTION 15: Regulatory information

15.1 Safety, health and environmental regulations/legislation specific for the substance or
mixture

This safety datasheet complies with the requirements of Regulation (EC) No. 1907/2006.

15.2 Chemical safety assessment

For this product a chemical safety assessment was not carried out

SECTION 16: Other information

Full text of H-Statements referred to under sections 2 and 3.

H225 Highly flammable liquid and vapour.

H319 Causes serious eye irritation.
H400 Very toxic to aquatic life with long lasting effects.

Further information
Copyright 2020 Aintech SpA License granted to make unlimited paper copies for internal use only.
The above information is believed to be correct but does not purport to be all inclusive and shall be used
only as a guide. The information in this document is based on the present state of our knowledge and
is applicable to the product with regard to appropriate safety precautions. It does not represent any
guarantee of the properties of the product. Aintech SpA, its Affiliates and Globuz bv-Nanometals shall
not be held liable for any damage resulting from handling or from contact with the above product. See
the reverse side of invoice or packing slip for additional terms and conditions of sale.

11

*GLOBUZ bv – Heidebergen 37 – 9830 Sint-Martens-Latem - Belgium