Scribd
Upload
3K views1 page

Engineering Design Calculation - Dennis Kirk Single Stage Centrifugal Pump Calculation (Clean Water Use) System Curve

This document provides calculations for a single stage centrifugal pump design. It details the static suction lift, static discharge head, total static head, friction losses, nozzle losses, velocity head, suction and discharge nozzle elevations, suction and discharge pressures. It then calculates the total dynamic suction lift, total dynamic discharge head, total dynamic head, net positive suction head available, and selects a nominal pump based on the required system flow rate, head, power requirements, and specifications.

Uploaded by

buntimehta007
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
3K views1 page

Engineering Design Calculation - Dennis Kirk Single Stage Centrifugal Pump Calculation (Clean Water Use) System Curve

This document provides calculations for a single stage centrifugal pump design. It details the static suction lift, static discharge head, total static head, friction losses, nozzle losses, velocity head, suction and discharge nozzle elevations, suction and discharge pressures. It then calculates the total dynamic suction lift, total dynamic discharge head, total dynamic head, net positive suction head available, and selects a nominal pump based on the required system flow rate, head, power requirements, and specifications.

Uploaded by

buntimehta007
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 1

ENGINEERING DESIGN CALCULATION - DENNIS KIRK [email protected].

au

SINGLE STAGE CENTRIFUGAL PUMP CALCULATION Pd Version 1.001 Nov-97


(Clean Water Use)
Static Suction Lift = Ls Pump Suction Diam = Ds SYSTEM CURVE
Static Discharge Head = Ld Pump Discharge Diam = Dd 250.00
Total Static Head Ltot = Ls + Ld

METRES HEAD
Friction Head = Hfs and Hfd Ho
Inlet and Discharge Nozzle Losses = Hi and Ho 200.00
Velocity Head = V2/2g [often included in pump curves] Pout Ld
Pump Suction and Discharge Nozzle Elevations = Lns and Lnd
Suction Pressure Head = Ps [if open tank = 0]
Discharge Pressure Head = Pd [if open tank = 0] Hfd 150.00
Vd
Lnd
L
C 100.00

Lns
Vs Ltot
Pout = Pd + Ld + Hfd + Ho - Lnd = Hd - Vd /2g - Lnd
2 50.00

Ls Hfs
Pin Pin = Ps - Ls - Hfs - Hi + Lns = - Hs - Vs2/2g + Lns 0.00
0 50 100 150 200 250 300 350 400 450 500
Ps
L/sec

Total Dynamic Suction Lift Hs = Ls - Ps + Hfs + Hi - Vs2/2g Dynamic Suction Lift (req'd) Hs(r) = Ls - Ps + Hfs + Hi
Hi Total Dynamic Discharge Head Hd = Ld + Pd + Hfd + Ho + Vd2/2g Dynamic Discharge Head (req'd) Hd(r) = Ld + Pd + Hfd + Ho
Total Dynamic Head Htot = Hd + Hs Dynamic Head (req'd) Htot(r) = Hd(r) + Hs(r)
NPSHa(req'd) NPSHa(r) = NPSHa - Vs2/2g
Closed Tank: NPSHa(abs) = Ps + Patm - Ls - Hfs - Hi + Vs2/2g - Pvap [where Pvap = Vapour Pressure(abs)] Provide this to pump vendor and use on pump curves
Open Tank: or = Pamb - Ls - Hfs - Hi + Vs2/2g - Pvap [NPSHa should exceed NPSHr by at least 0.5 m] where velocity head is included in vendors pump curves.

SYSTEM PROPERTIES SYSTEM CHARACTERISTICS PUMP SELECTION (Nominal)


Q 215 l/sec 0.2150 m3/sec Patm 10.329 m 101.325 kPa(abs)
SG 1 D 1000 kg/m3 Pamb 9.980 m 97.900 kPa(abs) Pump Speed 1483 rpm
Tfluid 16 o
C Vs 0.978 m 4.38 m/sec
Pvap 0.19 m(abs) 1.9 kPa(abs) Pinlet -2.669 m -26.180 kPa(g) Impeller Diam 0.449 m
Ps 0.00 m 0 kPa(g) Hs 1.991 m 19.531 kPa Pump Head 61.95 m
Ls 0.930 m 9.1 kPa Hs(r) 2.969 m 29.123 kPa
Hi 0.000 m 0 kPa Vd 2.387 m 6.84 m/sec Hydraulic Power 117.12 kW
Hfs 2.039 m 20 kPa Poutlet 51.452 m 504.741 kPa(g) Pump Efficiency 83.8%
Ds 0.250 m As 0.0491 m2 Hd 53.539 m 525.216 kPa Motor Power 139.76 kW
Lns 0.3 m 2.943 kPa Hd(r) 51.152 m 501.798 kPa
Pd 0.00 m 0 kPa(g) Specific Speed 1069
Ld -0.938 m -9.20178 kPa Htot 55.53 m 544.75 kPa
Ho 0.000 m 0 kPa Htot(r) 54.12 m 530.92 kPa NPSHr 2 m
Hfd 52.090 m 511 kPa Normally approx. 3% Htot 1.666 m
Dd 0.200 m Ad 0.0314 m2 NPSHa 7.79 m(abs) 76.47 kPa(g)
Lnd -0.3 m -2.943 kPa NPSHa(r) 6.82 m(abs) 66.88 kPa(g)

59581770.xlsx CENTRIFUGAL 12/09/2021

You might also like