INTELLISPEC™

System Guide Series V Integrated

Tunnel

Pressco Technology Inc.

69422 Rev. 01

Original Instructions
© 2011 Pressco Technology Inc. All rights reserved.
No part of this manual may be reproduced or transmitted in any form or by any means,
electronic or mechanical, including photocopying and recording, for any purpose,
without the express written permission of Pressco Technology Inc.
The contents of this manual are furnished for informational use only, are subject to
change without notice, and should not be construed as a commitment by Pressco
Technology Inc.
Written and designed at:
Pressco Technology Inc. World Headquarters
29200 Aurora Road
Cleveland, OH USA 44139-1847
TEL 440-498-2600
FAX 440-498-2615
www.pressco.com
Table of Contents
Chapter 1 Introduction....................................................................................................... 5
Welcome! ...........................................................................................................................................5
About this manual ..............................................................................................................................5
Typographical Conventions ...............................................................................................................5
Safety Considerations ........................................................................................................................6
Static Discharge Protection ................................................................................................................7
Chapter 2 Safety Information ............................................................................................ 9
Symbols .............................................................................................................................................9
Warning Devices ..............................................................................................................................11
Residual Risk ...................................................................................................................................12
Intended Use ....................................................................................................................................12
Non-intended use .............................................................................................................................12
Personal Protective Equipment........................................................................................................13
Personnel Safety ..............................................................................................................................13
Lifting heavy objects ........................................................................................................................15
Authorized Users..............................................................................................................................16
Spare Parts Usage ...........................................................................................................................16
Chapter 3 System Specifications .................................................................................... 17
Environmental conditions .................................................................................................................17
Specifications ...................................................................................................................................18
Declaration of Conformity - Intellispec System ................................................................................21
Declaration of Conformity - Integrated Tunnel .................................................................................22
Chapter 4 Installation and Wiring ................................................................................... 23
Shipping and Handling .....................................................................................................................23
Recommendations prior to installation .............................................................................................24
System Block Diagram - Integrated Tunnel .....................................................................................24
Assembly, location, and mounting requirements .............................................................................25
Commissioning.................................................................................................................................27
Chapter 5 Navigating Through the System .................................................................... 29
Intellispec cabinet and user interface ..............................................................................................29
User interface input devices .............................................................................................................31
User Interface Display - 4 Levels .....................................................................................................35
Menu Toolbar ...................................................................................................................................41
Online / Offline .................................................................................................................................43
Exiting the Intellispec software.........................................................................................................43
Chapter 6 User Accounts and Login Information .......................................................... 45
Logging in and logging out ...............................................................................................................45
Log in menu .....................................................................................................................................45
Switching users ................................................................................................................................46
Changing your password .................................................................................................................47
Managing user accounts ..................................................................................................................47
Exporting user accounts ..................................................................................................................50
Importing user accounts ...................................................................................................................51
Managing Permissions .....................................................................................................................52
Auto Logout setup ............................................................................................................................56

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Introduction i
© 2011 Pressco Technology Inc. Proprietary
Chapter 7 Graphs and Image Displays ........................................................................... 59
Trend Graphs ...................................................................................................................................59
Machine Part Graphs .......................................................................................................................62
Reject Images ..................................................................................................................................63
Timing Trend ....................................................................................................................................66
Inspections graph .............................................................................................................................66
Statistics Grid ...................................................................................................................................67
Walk By Graphic ..............................................................................................................................70
Big Live Image .................................................................................................................................74
Chapter 8 Alarms ............................................................................................................. 75
Viewing and Clearing Alarms ...........................................................................................................76
System Alarms .................................................................................................................................78
Lane Alarm Configuration ................................................................................................................78
Sensor Alarm Configuration .............................................................................................................81
Chapter 9 Tools Menus.................................................................................................... 85
Tools menu - System Overview Screen ..........................................................................................85
Tools menu - Lane Overview and Sensor Overviews Screens .......................................................86
Chapter 10 Software Utilities......................................................................................... 119
Adjusting Date and Time ................................................................................................................119
Setting up a printer .........................................................................................................................120
Creating a Support Package ..........................................................................................................120
Help - Remote Support ..................................................................................................................122
Discovery Software - What is Discovery? ......................................................................................124
Favorites Menu ..............................................................................................................................127
Chapter 11 Lighting and Imaging.................................................................................. 129
Sensor menu ..................................................................................................................................129
Saving Images ...............................................................................................................................144
Loading Images..............................................................................................................................156
Image Options ................................................................................................................................158
Chapter 12 Inspection Overview ................................................................................... 161
Inspection Terminology ..................................................................................................................161
Sequence of Events During Inspection ..........................................................................................162
Part Tracking ..................................................................................................................................162
How to Create, Copy, or Import a Part Program ............................................................................162
Part Changeover ............................................................................................................................165
Inspection menu .............................................................................................................................165
Inspection Tree Relationships ........................................................................................................172
Adding Regions and Inspections ...................................................................................................174
Region Editor .................................................................................................................................174
Inspection Editor ............................................................................................................................175
Retro-Spec Population View Graph ...............................................................................................179
Retro-Spec Part View Graph .........................................................................................................183
Chapter 13 Inspections.................................................................................................. 185
Empty Pocket .................................................................................................................................185
Regions of Interest (ROI) ...............................................................................................................186
Enhancements ...............................................................................................................................198
Registrations ..................................................................................................................................211

ii Introduction System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Orientations ....................................................................................................................................228
Analyses .........................................................................................................................................231
Dimensions ....................................................................................................................................266
Correlation......................................................................................................................................273
Chapter 14 System Hardware Information ................................................................... 275
Power Up .......................................................................................................................................275
Power Down ...................................................................................................................................276
Servicing the User Interface ...........................................................................................................277
Wiring Diagrams.............................................................................................................................277
Rebooting the Intellispec System ...................................................................................................283
Light Tree .......................................................................................................................................285
Chapter 15 Inspection Module Adjustments and Wiring Diagrams ............................ 287
Observe Part Image .......................................................................................................................288
Extended I/O in inspection modules ..............................................................................................289
CP/E Series modules .....................................................................................................................290
CP4422EV inspection module .......................................................................................................304
CP500 inspection module ..............................................................................................................313
CPX inspection module ..................................................................................................................316
Chapter 16 Extended I/O ................................................................................................ 321
Extended I/O board ........................................................................................................................321
Extended I/O in inspection modules ..............................................................................................328
Extended I/O Configuration ............................................................................................................328
Chapter 17 Maintenance Frequency ............................................................................. 331
Cleaning the Vision Processor filter ...............................................................................................332
Replacing/ Cleaning the Chromapulse CP4422EV Fan Filters .....................................................333
Cleaning Optical Surfaces .............................................................................................................333
Cleaning Glass Surfaces ...............................................................................................................334
Cleaning the Chromapulse Beam Splitter ......................................................................................334
Cleaning the Camera Lens ............................................................................................................335
Cleaning Plastic Surfaces ..............................................................................................................336
Cleaning the Ellipsoidal Mirror .......................................................................................................336
Cleaning the Part Detector .............................................................................................................336
Cleaning the Part Detector and Reflector ......................................................................................337
Replacing Filter/ Regulator Filters..................................................................................................338
Chapter 18 Defect Database Tool (option) ................................................................... 339
Search ............................................................................................................................................342
Search Results ...............................................................................................................................344
Reports ...........................................................................................................................................346
Maintenance...................................................................................................................................353
Help ................................................................................................................................................358
Chapter 19 How to Contact Pressco............................................................................. 359
Index.................................................................................................................................. 361

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Introduction iii
© 2011 Pressco Technology Inc. Proprietary
Chapter 1
INTRODUCTION

WELCOME!
Congratulations on your purchase of an Intellispec system! The Intellispec is a
high-speed machine vision system designed specifically for product and online process
monitoring. It is a very powerful tool that provides inspection much more reliably than
the human eye or sampling methods. The latest PC technology, powerful new inspection
algorithms, online adjustment capability, and inspection data storage allow the Intellispec
to automatically inspect parts with extreme accuracy on high-speed lines.
The Intellispec will help you provide the highest quality of products shipped to your
customers.

ABOUT THIS MANUAL

This manual:
Is considered to be valid as of release 5.0.455 of the Intellispec Series V software.
Contents of this manual are subject to change without notice.
Is considered an integral part of the system and should be kept handy for future
reference as long as the system is being used in your plant.
Is your responsibility to keep in good condition, in a dry place, and ready for
consultation by the authorized users (on page 16) of the system.
Contains the technology implemented at the time of selling and supplying the system
and shall not be considered inadequate in case of technological enhancements in the
machine or in the manual's illustrations.
Related books include:
Intellispec Series V Operator's Guide which has Operator-level user instructions, and
is a good place to start if you are new to Intellispec

TYPOGRAPHICAL CONVENTIONS
Following is a list of typographical conventions used in this manual:

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Introduction 5
© 2011 Pressco Technology Inc. Proprietary
 Bold type indicates a topic heading or an important item or statement.
Italicized type indicates emphasis.
Names of main components and system control signals have the first letter of each
word capitalized. For example: Processor Cabinet.
Danger messages appear as shown below:

Danger
Danger messages alert you to specific conditions that can cause serious or fatal
personal injury. Danger messages give you important information which must
be observed to prevent injury. These messages are set off from the body text
as shown here.
Caution messages appear as shown below:

Caution
Caution messages indicate important information which must be observed to
prevent: loss of data, poor system performance, or equipment damage.
These messages are set off from the body text as shown here.
Notes appear as shown below:
 Note: Notes contain special information that warrants being set off from the body
text as shown here.

SAFETY CONSIDERATIONS
Observe the following safety warnings when operating the Intellispec system or working
near it:

Warning
Potential for projectiles to strike persons and cause injury. Keep clear of reject
devices.

Warning
Sensitive electronics and High Voltages may be exposed. Keep Processor
Cabinet door closed.

6 Introduction System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 STATIC DISCHARGE PROTECTION

Caution
Electronic components can be damaged by static electricity discharge.
Always observe the following precautions before removing, installing or handling any
electronic components within the Inspection System:
Wear an anti-static wristband which is grounded to the Inspection System.
Stand on an anti-static, grounded floor mat, and lay circuit boards on the mat during
any board replacement.
Keep circuit boards in static shield bags when storing and transporting. Ensure the
bag is sealed.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Introduction 7
© 2011 Pressco Technology Inc. Proprietary
Chapter 2
SAFETY INFORMATION
This section contains operator safety information that must be read before operating or
servicing the system.

Warning
Do not, under any circumstances, tamper with sealed machine parts or devices.
This could result in the removal of protections that might create potentially
hazardous conditions.

Warning
This product contains no operator serviceable parts. Refer servicing to qualified
personnel. To prevent electrical shock do not open cabinet doors whilst
power is connected.

SYMBOLS
The following symbols are used on or near the Intellispec system. Be aware of potential
risk hazards.
CAUTION
Risk of danger. Refer to accompanying user documentation before use.

WARNING
Risk of electric shock

On (supply)

Off (supply)

Alternating current
Protective conductor terminal

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Safety Information 9
© 2011 Pressco Technology Inc. Proprietary
 Marking
The following illustration shows an example label that you will find on the Intellispec
Series V system components.

1 Name of component. NOTE: Chromapulse model is listed on the front

panel of the module. See example below.
2 Voltage range in Volts AC
3 Frequency range in Hertz (Hz)
4 Maximum rated power in watts (W) with all accessories or plug-in modules
connected
5 Serial number is listed in this box
6 Year of manufacture
7 Component certification
8 Risk of danger. Refer to accompanying documentation before use.

10 Safety Information System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 An example of a Chromapulse module label with the model number is shown below.

For additional markings, see the System Specifications (on page 17) section.

WARNING DEVICES
The Intellispec Series V system has warning devices that indicate system failure or report
excessive defects or warnings for your production line.

Alarms
User-programmable alarms allow you to set the duration of the lights in the optional light
tree and the horn if certain criteria are met.
In addition to the light tree, an alarm button is displayed on screen when certain criteria
are met. You can click the alarm button to clear the alarm (see "Viewing and Clearing
Alarms" on page 76)(s) and see more detailed information about the alarm condition.

Light Tree
The optional light tree may be mounted on or near an inspection module, or near a cluster
box (if applicable). The optional horn, mounted with the light tree provides an audible
warning.
For more information, refer to Light tree status (on page 285).
Light Tree (optional)
 Red (Alarm)
 Amber (Warning)
 Green (Online)
 Blue (Power)

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Safety Information 11
© 2011 Pressco Technology Inc. Proprietary
 RESIDUAL RISK
The Intellispec system has been designed to minimize any danger of personal injury.
However, the system uses rejection devices to remove defective product from the
production stream. Also, the electronics cabinets contain risk of shock if they are opened.
Observe the following safety warnings when operating the Intellispec system or working
near it:

Warning
Potential for projectiles to strike persons and cause injury. Keep clear of reject
devices.

Warning
Sensitive electronics and High Voltages may be exposed. Keep Processor
Cabinet door closed.

INTENDED USE
TYPE OF PROCESS
The Intellispec system is intended to monitor container and other special manufacturing
processes and identify non-conforming product.
INTENDED USE
The Intellispec system is designed and constructed for use in an indoor industrial
environment, always sheltered from the weather.
SPACE REQUIRED
The Intellispec machine and accompanying sensors must be installed in a place that will
enable safe and easy installation, size changeover, user operation, and maintenance
procedures.

NON-INTENDED USE

Warning
If this instrument is not used as specified, the protection provided by the
equipment could be impaired. This instrument must only be used in a normal
condition (in which all means of protection are intact).

12 Safety Information System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Important
The Intellispec system should NOT be used for any purpose other than
specifically indicated in the section titled Intended Use (on page 12).
The following uses are not intended:
Use in an explosive environment
Use in a flammable environment
Use in a damp, moist, or wet environment, except where specifically indicated

PERSONAL PROTECTIVE EQUIPMENT

Important
Always follow the safety requirements of your plant in addition to the
recommendations below.
We recommend, at minimum, use of the following Personal Protective Equipment (PPE):
Protective clothing

Protective gloves

Protective ear plugs or headphones

Protective eye wear

Protective foot wear

PERSONNEL SAFETY
The following rules are recommended to ensure the safety of personnel in charge of
machine operation and maintenance.
During machine operation:
Only one operator is needed to operate the machine. All others must keep
at a safe distance.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Safety Information 13
© 2011 Pressco Technology Inc. Proprietary
 Operators must be familiar with all machinery connected to the Pressco
equipment and know how to use emergency stop devices.
Note: the emergency stop devices may not be connected directly to the
Pressco equipment, but it is important to know how to use them.

Before putting the Pressco system online, the operator must ensure that all
safety devices used with all connected machinery are in place and
operational.

The operator must maintain maximum focus on his work and be alert
throughout his shift. If this is not the case, immediately inform the shift
supervisor.

When carrying out maintenance or repair work:

Disconnect master switch. For switch locations, refer to the Power Up (on
page 275) and Power Down section.

Before starting the machine, ensure that no person is close to the

machine.

If maintenance or repair requires the disconnection or removal of safety or

protection systems, this operation must be supervised by authorized
personnel who must ensure the prevention of personal injury or damage to
the machine. All machine movements must be performed with limited
speed and limited movements.
Maintenance or repair work on electrical components must be carried out
exclusively by authorized, trained personnel. When running tests with
power connected, you must strictly comply with the rules provided.

Personnel working on higher parts of a machine must wear a harness and

hook it on to the structure and must always move with extreme caution.

Never perform lubrication or maintenance procedures on mechanical parts

with the machine running.

14 Safety Information System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 For your safety, do not:
Open safety guards during machine operation
Perform maintenance and repair while the system is running
Lean on the machine
Sit on the machine components
Use the machine for purposes other than those listed in this manual
Modify parts of the machine
Allow unqualified personnel to operate or perform maintenance procedures on the
machine

LIFTING HEAVY OBJECTS

Caution
Some components are heavy. Take proper precautions to prevent personal
injury or damage to equipment. If you are not capable of lifting the object
alone, ask a capable person to help lift the object, or use a mechanical lifting
device
The components do not have handles to lift the equipment. Be sure to:
Lift equipment from the bottom - do not use wires, brackets, nor other protrusions
Keep fingers away from sensor lenses to keep the equipment clean
Proceed slowly

To safely lift equipment:

Caution
Do not twist your body when moving the load. Instead take small steps with your
feet turning until you are in the correct position.
1. Stand close to the load and center yourself over it with your feet shoulder width
apart.
2. Tighten your abdominal muscles.
3. Keeping your back straight, bend your knees and squat down to the floor.
4. Get a good grasp on the load with both hands.
5. Keeping the load close to your body, use your leg muscles to stand up lifting the load
off the floor.
 Your back should remain straight throughout lifting, using only the muscles in
the legs to lift the load.
6. To place the load in the appropriate spot, bend at the knees using only your leg
muscles to lower the load.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Safety Information 15
© 2011 Pressco Technology Inc. Proprietary
 AUTHORIZED USERS
Trained machine operators, mechanic and electrical maintenance staff, and plant
managers are considered authorized users of the Intellispec system. These users should
carefully read the information contained in this manual. The plant manager must ensure
that the safety recommendations included in this manual are observed.

Warning
Allowing workers who are unfamiliar with the production process to operate the
Intellispec system could result in hazard risk.
If you are unclear about any part of this manual, contact Pressco Technical Support (see
"How to Contact Pressco" on page 359).

Important
No worker should ever operate the system outside of his/ her own area of
competence and responsibility.
Proper Operation:
Only one worker is to operate the system at any given time. The correct position for the
operator is in front of the user interface monitor.
Repairs:
Any repair on the system shall be carried out exclusively by Pressco Technology Inc.
service personnel or by other service expressly authorized by Pressco Technology Inc.

SPARE PARTS USAGE

The following restrictions apply to replacing parts:

Warning
Using spare parts that are not designed to Pressco's specifications can
compromise the safety and effectiveness of the Intellispec system.
The use of parts that are not within Pressco's design specifications is prohibited. This
prohibition applies in particular when the parts involved contain or are connected
with safety devices.
Before resuming production, make sure all safety devices are in working order.
Pressco Technology Inc. shall not be liable in any way if any of the above-described
directions are not complied with.
To obtain a spare parts list, contact the customer service department at Pressco. How to
Contact Pressco (on page 359).
Pressco's technicians are available to help customers, in their own plant, to solve any
problem that might arise during use and maintenance of the Intellispec system.

16 Safety Information System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
Chapter 3
SYSTEM SPECIFICATIONS
This instrument has been designed and tested in accordance with Publication
EN61010-1:2001 Safety Requirements for Electrical Equipment for Measurement,
Control and Laboratory Use and has been supplied in a safe condition. The instruction
documentation contains information and warnings which must be followed by the user to
ensure safe operation and to maintain the instrument in a safe condition.

ENVIRONMENTAL CONDITIONS
The Intellispec Series V system is designed to be safe in the following environmental
conditions:
 Note: Please consult Pressco Technology Inc. (see "How to Contact Pressco" on
page 359) if your environmental conditions are outside of those listed.

Condition Specifications
Indoor/ outdoor use Indoor use only
Altitude Up to 2000 meters
Operating Temperature 5 °C to 50 °C
Storage Temperature 0 °C to 70 °C
Humidity Maximum relative humidity 80 % for temperatures up to 31 °C
decreasing linearly to 50 % relative humidity at 50 °C
Mains supply Voltage fluctuations up to ± 10 % of the nominal voltage
Overvoltage protection rating Transient overvoltage typically present on MAINS supply
NOTE: the normal level of transient overvoltages is impulse
withstand (overvoltage) category II of IEC 60364-4-443.
Rated pollution degree This instrument is designed for use in Installation Category II and
Pollution Degree 1 as per EN61010-1 and EN60664 respectively.

Warning
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.

Sound Pressure Level

The horn on the optional light tree (on page 11) has a maximum 105dB level at 1 meter
distance in front of the horn. Use proper hearing protection as specified by your plant
safety instructions.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) System Specifications 17
© 2011 Pressco Technology Inc. Proprietary
 SPECIFICATIONS
The following sections contain electrical specifications and measurements for
components of the Intellispec Series V system. Your system contains only the
components necessary for your application.

User Interface
User Interface Electrical Specifications
The following are electrical specifications for different configurations of the User
Interface:

Standard User Interface - No UPS included

Voltage Range 100-240VAC
Frequency 50/60Hz
Current 5A @ 120VAC, 100% Load

User Interface with Optional 750VA UPS, 120VAC Nominal

Voltage Range 100-132VAC
Frequency 50/60Hz
Current 6.3A @ 120VAC, 100% Load

User Interface with Optional 1KVA UPS, 230VAC Nominal

Voltage Range 200-240VAC
Frequency 50/60Hz
Current 4.3A @ 230VAC, 100% Load

18 System Specifications System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 User Interface measurements
The following are the weight and dimensions of the Intellispec Series V User Interface
(see illustration below):

1656
65

504 600
20 24

Measurement Value
Weight (total user interface) 79.7 Kg [177 lb]
Weight (stand with monitor 31 Kg [68 lb]
arm and all attached
components)
Weight (computer) 25 Kg [55 lb]
Weight (Monitor) 11.3 Kg max [25 lb]
Weight (UPS) 12.7 Kg [28 lb]
Height 1656 mm [65 in]
Width 504 mm [20 in]
Depth 600 mm [24 in]

Integrated Tunnel Electrical Specifications

The following are electrical specifications for the integrated tunnel (an inspection module
that contains cameras and part tracking in one unit, such as the CP/ EV series tunnels).
Standard - No UPS
Voltage Range 100-240VAC
Frequency 50/60Hz
Current 6.2A @ 120VAC, 100% Load

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) System Specifications 19
© 2011 Pressco Technology Inc. Proprietary
 Optional 500VA UPS, 120VAC Nominal
Voltage Range 100-132VAC
Frequency 50/60Hz
Current 4.1 @ 120VAC, 100% Load

Optional 500VA UPS, 230VAC Nominal

Voltage Range 200-240VAC
Frequency 50/60Hz
Current 2.2A @ 230VAC, 100% Load

CP/EV module measurements

The following are the weights and dimensions of the CPxx/ EV series inspection
modules:

648 254

279

Measurement Value
Weight 16.4 Kg [36 lb]
Height 648 mm
Width 254 mm
Depth 279 mm

 Note: measurements do not include connectors

Caution
This object is heavy. Review the section on lifting heavy objects (on page 15)
before moving this object.

20 System Specifications System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 DECLARATION OF CONFORMITY -
INTELLISPEC SYSTEM

We,
Pressco Technology, Inc. of 29200 Aurora Road, Cleveland, Ohio USA 44139-1847,
hereby declare under our sole responsibility that the following machinery complies with
the essential health and safety standards and protection requirements of the following
standards:
Electromagnetic Compatibility Directive 2004/108/EC
Low Voltage Directive 2006/95/EEC

Machine description: AUTOMATED MACHINE VISION INSPECTION SYSTEM

Make: Pressco Technology Inc
Model Number: INTELLISPEC™ Series V

We certify the above product and its components have been designed and manufactured
using the following transposed harmonized European standards:
EN50081-2 Generic Emissions Standards
EN55011 Class A/CISPR 11
EN 50082-2 Generic Immunity Standards
EN61000 4-2 ESD: 4kV CD/8kV AD
EN61000 4-3 RFI: 10V/m
EN61000 4-4 EFT: +/-2kV Power Lines, +/-1kV Signal Lines
EN61000 4-6 Conducted RF
EN60950 Safety of Information Technology Equipment

A technical construction file for this product is retained at the above address.

Signed: Date:
Name: Noel E. Morgan Jr. Title: VP of Operation
Being the person authorized by the manufacturer to sign on their behalf.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) System Specifications 21
© 2011 Pressco Technology Inc. Proprietary
 DECLARATION OF CONFORMITY -
INTEGRATED TUNNEL

Number: EMC2932
Declaration: The Pressco Technology, Inc. Intellispec Series V Inspection System is in
conformity with Directive 2004/108/EC of the European Parliament and of the Council
of 15 December 2004 on the approximation of the laws of the Member States relating to
electromagnetic compatibility and repealing Directive 89/336/EEC, and with Directive
2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the
harmonization of the laws of Member States relating to electrical equipment designed for
use within certain voltage limits.
Manufacturer: Pressco Technology, Inc.
29200 Aurora Road
Cleveland, Ohio 44139-1847
USA
Product Identification: Product Name: Intellispec Series V Inspection System
Standards Used (only major standards listed):
EN 61326-1:2006: Electrical equipment for measurement, control and laboratory
use —EMC requirements — Part 1: General requirements
EN61010-1 (2001): Safety requirements for electrical equipment for measurement,
control and laboratory use - Part 1: General requirements
Technical File: MS2932
Place: Pressco Technology, Inc. April 30, 2010
29200 Aurora Rd.
Solon, Ohio 44139-1847
USA
Signed: Date:
Name: Noel E. Morgan Jr. Title: VP of Operation
Being the person authorized by the manufacturer to sign on their behalf.

22 System Specifications System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
Chapter 4
INSTALLATION AND WIRING

SHIPPING AND HANDLING

Pressco Technology Inc. ships unassembled components in packing cases designed to
protect the contents during handling and from exposure to weather.
Unless otherwise specified in the contract with the machine order, the Customer shall
supply Pressco Technology Inc. with the means and equipment necessary for the
unloading, lifting, and handling of machine parts. Pressco Technology Inc. deems it
important to have one of their technicians supervise the process of unloading, handling,
and lifting the machine. The technician can give useful advice as to the logical sequence
in which the components should be unpacked and positioned for ease of assembly.

Warning
Only qualified personnel must be involved in the operation of unloading,
handling, and lifting the machine. Pressco Technology Inc. shall not be liable
for damage to components and/or personal injury resulting from the
involvement of unauthorized personnel and/or failure to comply with the
directions provided in this manual in relation to lifting and transport.

Important
The site supervisor will be responsible for ensuring that all the various mounting
phases are carried out safely and in compliance with current regulations.
After the machine is delivered, check for any damage that might have occurred during
shipping. In case of damage, contact Pressco Technology Inc (see "How to Contact
Pressco" on page 359).
In handling the machine, always keep it close to the ground.

We recommend using a forklift truck with adequate capacity and forks to

suit the weight to be lifted (machine plus packaging).
The dimensions and weight of a crate are listed below. Note that this is the maximum
size and weight. The size and weight of the crate may be less depending on your
configuration. You may receive multiple crates depending on your configuration.
Size 152.4 cm x 124.46 cm x 152.4 cm (60 x
49 x 60 inches)
Weight 453.592 kg (1000 lbs.)

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Installation and Wiring 23
© 2011 Pressco Technology Inc. Proprietary
 RECOMMENDATIONS PRIOR TO
INSTALLATION
Before the machine is installed, the Pressco installer, together with the Customer (or
representative) shall check the following criteria in the environment where the machine
is to be installed:
Work required by contract for the installation of the machine has been carried out
The plant layout drawing that describes where the machine will be installed is the
final drawing agreed to by Pressco Technology Inc.
The space and height required for installation are actually available
Only the components included in the installation layout are present in the area where
the machine is to be mounted. Ensure no machines or components have been added
at a later stage that might hinder mounting or make it more difficult. Should this be
the case, immediately contact Pressco's Project Management personnel to arrange a
suitable solution to the problem.
We recommend the following prior to machine installation:
Transport the machine in its packaging to the area where it will be installed to
minimize possibility of damage
Carefully remove the packaging material and check components for damage
Check tightness of mechanical components, as they can loosen during transport
Prepare the compressed air mains line. Before making final connections, ensure that
the pipes are clean and free from any debris.

SYSTEM BLOCK DIAGRAM - INTEGRATED

TUNNEL
Below is a basic block diagram for Series V Intellispec. This drawing shows the major
components for the system. Your system will contain only the components required for
your application. The numbered components are listed in the table below.
The drawing below shows a basic block diagram for a system with an integrated tunnel
(with one camera).

5
2
1

3 7

6 6

24 Installation and Wiring System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 1 User Interface (PC, monitor, and UPS)
2 PDN (Pressco Data Network) ethernet green cable
3 Inspection sensor/ camera ethernet blue cable
4 Light tree (optional)
5 Sensor cables (for part present sensor, encoder, machine part, pocket
detect, reject confirm) For details: I/O connectors (see "Chromapulse
module external connections" on page 298)
6 AC power
7 Integrated tunnel (example: CP/EV inspection module)

ASSEMBLY, LOCATION, AND MOUNTING

REQUIREMENTS
The Intellispec requires the following:

Utilities to be supplied by customer

The following utilities are required to operate the Intellispec Series V system. Before
making connection, make sure the utility matches the technical specifications. More than
one connection of the utilities may be required depending on the number of modules
installed. Refer to specific wiring diagrams.
Utility Requirements
Air supply for rejection Pipe size must be such that there will be no pressure decrease during
device machine operation. Air must be dry and free of oil.
Electrical supply Provide one each electrical socket to comply with:
 User interface electrical specifications (on page 18) (use the
specifications that apply to your system)
 Integrated tunnel electrical specifications (on page 19) (if applicable)
 Cluster box electrical specifications (if applicable)
Internet connection Provide a shielded ethernet cable to use Pressco's remote support through
(optional) the Internet.

Protective earthing
This product must be grounded (earthed). If it should malfunction or break down,
grounding provides a path of least resistance for electric current to reduce the risk of
electric shock.

Danger
Improper connection of the equipment grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or service technician if you
are in doubt as to whether the product is properly grounded.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Installation and Wiring 25
© 2011 Pressco Technology Inc. Proprietary
 Cord Connected Equipment
The product will be equipped with a supply cord having an equipment grounding
conductor and a grounding plug. The plug must be plugged into an appropriate outlet that
is properly installed and grounded in accordance with local codes and ordinances.
Do not modify the plug provided with the product - if it will not fit the outlet, have a
proper outlet installed by a qualified electrician.
Cable Direct
This product must be connected to a grounded metal, permanent wiring system, or an
equipment grounding conductor must be run with the circuit conductors and be
connected to the equipment rounding terminal.

Electrical connection
Make sure that the power outlet voltage matches the voltage required by the machine.
Refer to the specifications for equipment included with your system:
User interface electrical specifications (on page 18)
Integrated tunnel electrical specifications (on page 19)
Cluster box electrical specifications

Warning
Power Switch is the power disconnect device. Do not position the equipment
such that access to the disconnect switch is impaired. If not readily
accessible (such as within a rack or mounting out of reach), an additional
disconnect device should be installed that can isolate the Live and Neutral
lines of the mains power supply, whilst leaving the protective earth intact.

Installation
Pressco Technology Inc. recommends that the machine be installed and assembled by
Pressco's specialized technicians. This is of vital importance for correct machine
operation.

Warning
Pressco Technology Inc. shall not be liable in case of failures or damage to
property and/or personal injury resulting from or connected with assembly if
this has been carried out by unauthorized personnel, or is not in compliance
with the indications given in this manual.
To carry out production and cleaning/ servicing operations, it is important for the
machine to have a minimum amount of space all around and away from walls.

Ventilation
Place the Intellispec Series V components in a position with adequate ventilation to allow
proper air flow through the air filters.
Component Spacing
User Interface Leave 1 meter [39 inches] clear around machine
26 Installation and Wiring System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Component Spacing
Cluster box (not used on all Leave 100 mm clear in front of the fan and vent
systems)

Stability of user interface

Ensure the stability of the user interface. Also refer to the directives in the Personnel
Safety (on page 13) section.

1 2

To make sure the user interface is stable:

1. Make sure that the user interface stabilizer [item 1] is secured properly to the user
interface.
2. Adjust the feet [item 2] to level the user interface. Proper leveling can help ensure
proper operation.

COMMISSIONING
Before placing the machine into operation, make sure the following checks are
completed:
Completed Yes No
Positioning and leveling of the unit
Connection of compressed air line to connection points
Connection of power supply to user interface cabinet
Connection of power supply to cluster box (if applicable)
Connection of power supply to integrated inspection module(s) if
applicable
Proper wiring from user interface cabinet to sensor module(s) and
cluster box (if applicable) using the wiring diagrams

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Installation and Wiring 27
© 2011 Pressco Technology Inc. Proprietary
28 Installation and Wiring System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
Chapter 5
NAVIGATING THROUGH THE SYSTEM
This section describes the regions of the user interface and how to navigate through the
software. It also describes how to select items and how to use the user interface buttons.

INTELLISPEC CABINET AND USER

INTERFACE

1 24" Diagonal color LCD with optional touch screen. An on-screen

keyboard (OSK) is displayed when needed.
2 Trackball with two sets (left-handed or right-handed) of buttons: Select
buttons [ ] and Information buttons [ ]
3 Vision processor on/off switch.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Navigating Through the System 29
© 2011 Pressco Technology Inc. Proprietary
 4 Inside the cabinet:
 Ethernet switches
 Vision processor
 Mechanical keyboard (MKB)
5 USB convenience port is mounted on the side of the user interface.

Monitor
The standard monitor is an LCD color monitor mounted on a mechanical arm to allow
the user to tilt or swivel the screen for best viewing. It has an area of 1920 x 1200 pixels
and a diagonal size of about 24 inches.

Touch Screen Monitor (optional)

Some Intellispec systems have a touch screen monitor installed. It has an area of 1920 x
1200 pixels and a diagonal size of about 24 inches. This is used primarily for high level
navigation, obtaining information from the system, and responding to alarms. It is not to
be used for inspection setup or configuration tasks, as those tasks require detailed input.

Use the touch screen to:

Log in / out
Put the system online / offline
Clear statistics
Print reports
Acknowledge or reset Alarms
Navigate the menus (from System Overview to Lane View to Sensor view, etc.)

30 Navigating Through the System System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 USER INTERFACE INPUT DEVICES
The following devices are available to input information to the Intellispec system:
Trackball and buttons (see "How to select menu items" on page 31)
On Screen Keyboard (OSK) (on page 32)
Touch Screen monitor (optional) (on page 30)
Temporarily connected conventional Mechanical Keyboard (MKB) (on page 34)
USB Ports (on page 34)
Optional Biometric Identification login device (see "Biometric login device
(optional)" on page 35)

User interface selection devices

The user interface hardware consists of several buttons and selection devices:
1 2

3 5

4 6
7

1 (not a button) Grommet for user interface equipment cords.

2 Optional Biometric Identification login device
3 and Secondary set of buttons, used with track ball. See also items 6 and 7.
4
5 Track Ball
6 Button (left-click) to select and activate objects on screen
7 Button (right-click) to call up a context-sensitive menu about the selected
object on screen

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Navigating Through the System 31
© 2011 Pressco Technology Inc. Proprietary
 How to select menu items
Use the track ball to select, interact, and change active objects on the screen. The track
ball will be required for all inspection editing tasks.
Under the track ball are two buttons. Use the left button (the primary button ) to
select and activate objects on the screen. Use the right button to call up a
context-sensitive menu related to the area or object clicked. A second set of each button
type is located on the left side of the podium for two-handed operation.
 Note: Swapping the button assignments is not supported. The second set of buttons is
to accommodate left-handed users.
The following table shows the actions available for the track ball and buttons, and the
results of those actions.
Action Result
Point (move pointer with the Display Tool Tip when hovered over active object
track ball)
When the pointer is over an active object, a click
Click (Left-click) initiates various actions. Nothing happens when
the pointer is clicked on a disabled object.
When the pointer is over an active object, a
Double-click double-click initiates various actions. For
example, edit an inspection.
Display a context-sensitive menu when you click
Right-click on an enabled object. The context-sensitive menu
often contains functions that are also available in
a menu bar or other screens. For example, add a
point to a polygon.
Drag (hold the left button while Examples: move a selected Region of Interest
moving the track ball) (ROI) around an image or move an inspection in
a Tree View to change the order of execution.

32 Navigating Through the System System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 On Screen Keyboard (OSK)
Different types of on screen keyboards will be displayed depending on what kind of
input is needed. When you want to type text or numbers into a field, right-click or
double-click on a text input field to display the appropriate keyboard.
If alphanumerical input is needed, a full alphanumeric keyboard will be displayed
In numeric input only is needed, a smaller, numeric keypad only will be displayed
ALPHANUMERIC KEYBOARD

1 Shift lock button - capitalizes all letters until you press this button again.
2 Shift button - capitalizes one letter, then returns to uncapitalized letters
automatically.
3 OK button - accepts the typed information and closes the keyboard screen.
4 Cancel button - disregards the typed information and closes the keyboard
screen.

NUMERIC KEYBOARD
The numeric keypad is displayed when the input field requires a numeric entry. Most of
the buttons are self-explanatory. Additional buttons are described below.
 Note: some buttons are not displayed if they are not appropriate for that field.

1 Backspace - removes a digit

2 Enter - populates the field in the Intellispec screen without closing the
keyboard. This is useful if you want to test a value and see the results of
the change immediately.
System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Navigating Through the System 33
© 2011 Pressco Technology Inc. Proprietary
 3 [+/-] makes the number positive or negative
4 [.] available only if a decimal number is valid in the input field
5 [<=>] cycles to the next limit of the parameter. If the parameter has more
than two limits, then asterisks will surround the selected value in the menu.

6
accepts your changes and closes the numeric keypad

Mechanical keyboard (MKB)

The system supports the temporary connection of a conventional mechanical keyboard
using one of the available USB ports (on page 34). This keyboard will mostly be used for
system level tasks such as BIOS configuration, Network configuration, and Operating
System level setup.

The keyboard:
Is primarily used by Pressco Field Service Engineers
Is stored inside the Vision PC chassis
Requires a stable location when in use

USB Ports
There are USB ports available to back up or transfer data, and also to connect the
optional mechanical keyboard. One is mounted on the side of the user interface pedestal.
Some touch screen monitors have additional USB connectors on the side of the monitor.

34 Navigating Through the System System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Biometric login device (optional)
The optional Biometric Identification login device (see "Adding a user with the
biometric login device" on page 48) is used to log in and out of the Intellispec system.

To log in with this device, press your finger to the device. The following are conditions
for use:
You must use the same finger as initially set up by your administrator
If you do not know how your account was set up (or which finger you used), contact
your administrator
If, after three tries, the Intellispec does not recognize your finger print, you must log
in using the on screen keyboard (OSK (see "On Screen Keyboard (OSK)" on page
32))

USER INTERFACE DISPLAY - 4 LEVELS

The display on the user interface has four levels for viewing:

Look at the tab at the top of the screen to quickly determine which level you are viewing
(from System Overview to Sensor Overview). The tab will read "System Overview"
[level 1], "Lane n" [level 2], or "sensor name" [level 3]. In the Inspection Screen [level
4], the tab also reads "sensor name," but the inspection graphs and parameters are
available to view and edit.
 Note: when you switch between System Overview and Lane Overview modes, you
will see one screen 'minimize' to the task bar while your selected screen is displayed.
This is normal.

To view the four viewing levels:

1. Click the Home button to go to level 1, System Overview.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Navigating Through the System 35
© 2011 Pressco Technology Inc. Proprietary
  System Overview - Displays information that represents the complete system as
well as a thumbnail line for each Lane that is configured. More information
about the System Overview screen (on page 37).

2. Click a Lane button to go to level 2, Lane

Overview.
 Lane Overview - Displays information for a particular Lane as well as a
thumbnail line for each sensor used in that Lane. More information about the
Lane Overview Screen (on page 38).

3. Click a Sensor button to go to level 3, Sensor Overview.

 Sensor Overview - Displays information for a particular sensor, including an
image area, sensor statistics, a graphics area that displays user-selectable graphs,
and a user-selectable inspection list. More information about Sensor Overview
Screen (on page 40).

4. Double-click an inspection name in the Analysis Inspections list to

get to level 4, Inspection Screen.

36 Navigating Through the System System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Note: Some menu items are only available to advanced level users.
 Inspection Screen - Double-click on any inspection name to see this view, which
allows you to see inspection parameters and make changes if necessary.

5. Click the exit button to go back to level 3 Sensor Overview mode.

System Overview screen

1 Select the tab to display desired sensor image

2 Current Part Program
3 Online/ Offline
4 Click to go to Lane Overview
5 Lane Statistics
6 Heartbeat Image
7 Cycle the displayed Heartbeat Image

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Navigating Through the System 37
© 2011 Pressco Technology Inc. Proprietary
 8 Log in
9 Home
10 Alarms
11 System Settings
12 Favorites
13 Wizards
14 Language
15 Help menu (Remote support only at System Overview)
16 Walk By Graphic

Lane Overview Screen

1 Click the sensor button to toggle to detailed Sensor View and back
2 Switch to System Overview

More Lane Information

Under the Lane Overview screen, click the More Lane Information bar to display
additional graphs, statistics, or an additional Walk By graphic. Buttons on the right side
of the screen provide different viewing options.

38 Navigating Through the System System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Sensor Information

Under the Lane Overview screen, click the Sensor Information bar (at the bottom of the
screen) to display the default sensor information. Graphs, images, or statistics are
displayed depending which button on the right is selected.

Statistics menu
Use the Statistics menu in the Lane Overview screen to view, reset, or print statistics.
 Note: Some menu items are only available to advanced level users.

To view the Statistics menu:

1. Go to the Lane Overview screen by clicking a Lane n button.
2. Click over a statistics box. The Statistics menu is displayed. The items in the menu
are described below.

Reset Lane Statistics

Reset the statistics for the lane only.
Reset Lane Statistics and Clear Images
Reset the statistics for the lane and empty the defective image buffer.
Print Lane Report
Send the lane statistics report to the default configured printer.
Statistics Last Reset
Display the date and time when the lane statistics were last reset.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Navigating Through the System 39
© 2011 Pressco Technology Inc. Proprietary
 Sensor Overview Screen

1 Double-click to open Inspection View

2 Switch to System Overview

40 Navigating Through the System System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Inspection Overview Screen

1 Close the Inspection View

2 The inspection window must be closed first to switch to System Overview

MENU TOOLBAR

1 Home
2 Alarms
3 Tools
4 Favorites
5 Wizards

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Navigating Through the System 41
© 2011 Pressco Technology Inc. Proprietary
 6 Language
7 Help

Home
Click Home to return to the System Overview Screen. If a region or inspection editor
menu is open, you must close it before anything else can be selected. The Home
button is highlighted in the System Overview screen.
Alarms
When this icon is selected, a different pop-up window appears depending on what
screen you are on. For more information, refer to the section about alarms.
Tools
When this icon is selected, a different pop-up window appears depending on what
screen you are on. For more information, refer to the section about tools.
Favorites
From the Lane and Sensor Overview screens, you can select between Print Screen
and Defect Database.
Wizards
From the Lane or Sensor Overview screens, select wizards that assist in setting up
certain features. At the present time the only wizard is for setting up the Walk By
graphic. This allows you to select group names, inspections assigned to each group,
and values that determine when areas of the Walk By graphic turn to yellow, red, or
back to normal (green).
Language
Select an available language from this menu (when available).
Help
From the Lane or Sensor Overview screens, access the help documents, support
package utility, remote support option, and software version.

Language

Click the language button to select a different language. Choose from the
available options.

Help

Click the Help icon to access Pressco remote support, create a support package
(see "Creating a Support Package" on page 120), obtain your current software version,
or use the help files.
To access the user manuals:

1. Click the Help icon .

2. Select Help Documents, then Help. The user manual is displayed.

42 Navigating Through the System System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 ONLINE / OFFLINE
 The stoplight is the online/offline indicator for each lane. A red light indicates the
lane is offline; a green light indicates the lane is online.
 To switch from the online to offline mode, or vice versa, click the stoplight.
 Lanes can be put online or offline independently. If multiple lanes are configured,
then one can be offline while another is online.

EXITING THE INTELLISPEC SOFTWARE

You must have proper user permissions to exit the software. This prevents unauthorized
system shutdowns. Contact your system administrator if you need user permissions.
To exit Intellispec software:
1. Log in.

2. Click the Home button .

3. Click the Tools button to display the Tools menu.

4. Click the Exit System option. The Intellispec software shuts down.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Navigating Through the System 43
© 2011 Pressco Technology Inc. Proprietary
Chapter 6
USER ACCOUNTS AND LOGIN
INFORMATION
This section describes how to log in and how to manage user accounts.

LOGGING IN AND LOGGING OUT

Each user account has a list of permissions and restrictions. This is to give administrators
more control over the system, and restrict others from performing tasks like changing
lighting, or adding and editing inspections. When you log in, you can perform the tasks
made available to you.
To log in, follow either of the steps below:

Click the Log In button to display the login dialog

box. Select your user name from the drop-down list. Enter your password using the
On Screen Keyboard by touch screen or trackball and buttons. The password
characters will not be shown for security reasons.
[With the optional biometric sensor] Press your finger to the sensor. The system
will automatically determine your identity and log you in. If the system fails to
recognize your identity after three attempts, the log in dialog box will appear, to
allow you to log in with your user name and password.
To log out, follow either of the steps below:
Click the Log In button that displays your user name. The account drop-down menu
appears. Select the Log Out button. The system logs you out.
[With the optional biometric sensor] Press your finger to the sensor. The system
logs you out.
 Note: When another users logs in, the system automatically logs you out.

LOG IN MENU
To ensure that only authorized users perform certain changes to the system, users are
required to log in*.
 Note: Accounts may be shared by a group of people (example: Shift 1).

To view the Log In menu:

1. Click the Log In button and enter your password. The

text on the button changes to indicate who is logged in.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) User Accounts and Login Information 45
© 2011 Pressco Technology Inc. Proprietary
 2. Click the Log In button again (which has your user name displayed on it). The Log
In menu is displayed. Some options in this menu are only available to authorized
users.

1 Logout - Logs out whoever is logged in

2 Switch user - Allows you to switch from one user to another
3 Change Password (see "Changing your password" on page 47)- Allows
you to change only your password
4 Manage Users (see "Managing user accounts" on page 47) – Used to
assign, remove, or edit users. This is where users are given access to
specific tasks (example: one user is given the access to edit inspections
and another is not given this access). You can also give users access to
specific tasks through Manage Permissions (see "Managing
Permissions" on page 52).
5 Export Users (see "Exporting user accounts" on page 50) - Allows you
to export user profiles from one Intellispec to another
6 Import Users (see "Exporting user accounts" on page 50) - Allows you
to import user profiles from one Intellispec to another
7 Manage Permissions (see "Managing Permissions" on page 52) – This
is where the system can be configured to allow pre-defined tasks to be
performed with no log-in
8 Setup Auto Logout (see "Auto Logout setup" on page 56)– This feature
will automatically log you out if there is no activity for a defined amount of
time
*Some tasks can be configured so that users do not need to log in. This is done through
Manage Permissions (see "Managing Permissions" on page 52).
 Note: There is a Pressco Technician account for use only by Pressco Service
Engineers. This gives access to unsupported features (menu items are a different
color). If you log into this account and use those features, do so at your own risk.

SWITCHING USERS
The Switch Users option from the Log In menu logs out the current user, and allows a
new user to log in.
To switch users:
1. Click the Log in button (which has the current user's name displayed).
2. Select Switch Users from the menu.
3. Select the new user name from the drop-down menu.
4. Enter the new user's password. The new user is logged in. The previous user is
logged out.

46 User Accounts and Login Information System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 If you have a biometric sensor:
Press your finger to the biometric sensor device to log in. The previous user will be
automatically logged out by the system.

CHANGING YOUR PASSWORD

The Change Password function is available to all users.
 Note: an Administrator can reset a password if necessary.

To change your password:

1. Log in.
2. Click the Log In button with your user name to see the Log In menu.
3. Select Change Password. The Change Password dialog box is displayed.
4. Enter your Old Password.
5. Enter a New Password.
6. Confirm your New Password.

7. Click the OK button to accept the changes. The dialog box closes and your
password is changed.

MANAGING USER ACCOUNTS

The Manage Users button is only available to those with the Manage Users permission.
This feature provides a wizard that allows you to Add a new user, Edit a current user or
Remove any user. You may create one user account for a group of people and give that
group the password to the account (example: Shift 1).
 Note: the biometric login features are only used when the optional biometric login
device is installed

To manage a user account:

1. Log in as an administrative user.
2. Click the button with your user name to see the login drop-down menu.
3. Select Manage Users. The Manage Users dialog box is displayed.
4. Select Add, Edit, or Remove a user. Follow the information on screen to complete
these actions. The current step is highlighted on the left side of the configuration
screen [item 1 in illustration below], and is repeated at the bottom of the screen.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) User Accounts and Login Information 47
© 2011 Pressco Technology Inc. Proprietary
 5. Use the forward arrow button [item 2] to move to the next screen after you have
entered the appropriate information. Use the back arrow button (not shown in first
step) to return to the previous step. You do not need to enter information in each
screen to move from one screen to the next.

1 Current step in the wizard is highlighted.

2 Forward navigation to move to the next step. A back arrow (not shown) is
available in later steps.

Adding a user with the biometric login device

When you have the optional biometric login device installed, you will need the user
present. The biometric login uses finger recognition software to log in rather than
selecting a user name and entering a password. You can always log in (see "Logging in
and logging out" on page 45) using your user name and password, even if you have a
biometric login device. The maximum number of biometric accounts is 40.
 Note: use of one account by a group of people is not supported with the biometric
device. Each user must have his or her own account.

48 User Accounts and Login Information System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
  Additionally, you cannot create two accounts for the same finger print. You could
create two accounts for one person, but you must use two different fingers.

To add a user with the biometric login device:

1. Log in as an administrative user.
2. Click the button with your user name to see the login drop-down menu.
3. Select Manage Users. The Manage Users dialog box is displayed.
4. Click the Add button.
5. Add the user name when prompted. Click the forward arrow.
6. Enter a password, then Confirm it. Click the forward arrow.
7. [Biometric login] The next screen gives you the option of creating a biometric login
or skipping over it. If you chose Skip, go to step 10. If you chose Create, go to step 8.
8. [Select Finger] Choose which finger the biometric sensor will read. Select any finger
by using the touch screen or trackball and buttons to choose the circle above the
finger. Only one finger can be used, and you must use this finger every time when
logging in. Click the forward arrow.

9. [Read Finger] Click the Start Button at the top of the screen. The system will ask you
to place the finger you selected on the biometric sensor. To ensure an accurate
biometric measurement, you are asked for three readings. Instruct the user to place
his or her finger on the biometric sensor three times when prompted. Click the
forward arrow.
10. [Permissions] This is where you can set up what each user can and cannot do within
the system. After you have selected the desired permissions, click the forward arrow.
You can also change permissions later. For more information, see Managing
Permissions (on page 52).
System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) User Accounts and Login Information 49
© 2011 Pressco Technology Inc. Proprietary
 11. [Finished] Click the OK button to accept changes and exit.

EXPORTING USER ACCOUNTS

This allows you to export user accounts from one system to another. The user accounts
may be used in other Intellispec Series V systems in your plant. You may also want to
back up your user accounts in the event they are changed in the system.
What you need:
A USB memory device to export or import data
User access permission to change permissions
To export a user account:
1. Log in as an administrative user.
2. Insert the USB (see "USB Ports" on page 34) device into an available slot on the
Intellispec Series V system.
3. Click the button with your user name to see the login drop-down menu.
4. In the user login drop-down menu, click Export Users. The Export Users dialog box
is displayed.

5. Select the user account that you want to export.

6. Click the right arrow to export the user account.

7. Choose the destination to save the user account from the drop-down menu, or click
the Save button to browse to the USB device.

8. Click OK to accept changes and exit the screen. The user account is exported.

50 User Accounts and Login Information System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 IMPORTING USER ACCOUNTS
This allows you to import user accounts from one system to another. The user accounts
may be used from other Intellispec Series V systems in your plant.
What you need:
A USB memory device with user accounts already saved on it, or a folder on the
Intellispec hard drive with valid user accounts
Administrative access to user accounts
To import a user account:
1. Log in as an administrative user.
2. Insert the USB (see "USB Ports" on page 34) device into an available slot on the
Intellispec Series V system.
3. Click the button with your user name to see the login drop-down menu.
4. In the user login drop-down menu, click Import Users. The Import Users dialog box
is displayed.

5. Select the user account that you want to Import from the right column. If you do not
see any users available, click the Save button to browse to a location where the
user account is saved.

6. Click the left arrow to import the user account.

7. Click OK to accept changes and exit the screen. The user account is imported.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) User Accounts and Login Information 51
© 2011 Pressco Technology Inc. Proprietary
 MANAGING PERMISSIONS
The Intellispec has some default permissions that you can use to quickly set up users. To
grant these permissions, click the appropriate button in the Manage Users screen. When
you select these default permissions, you could also add or subtract specific permissions
for the user.

1 Choose from one of the predefined Roles to use the default permissions
2 Subtract one of the Granted Permissions. First highlight the permission in
the list, then click the left arrow.
3 Choose one of the Denied Permissions to be granted. First highlight the
permission in the list, then click the right arrow.
Notes about roles and permissions:
Granted permissions have priority over roles. If you change the permissions of a role,
or change the role of a user, the granted permissions persist.
When you change permissions for a role, all users with that role get the new
permissions of that role. This is useful to change permissions for groups of users.

Standard Role Setups Default Permissions

None None
Operator Online
Offline
Enable inspection items
Open help sessions
View change logs
Mechanic Access image tools
- all Operator permissions, plus: Access system configuration
Access system diagnostics
52 User Accounts and Login Information System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Standard Role Setups Default Permissions
Clear statistics
Configure alarms
Configure charts
Configure walk-by graphic
Edit inspections
Edit lighting
Enable inspection items
Forced reject sampling
Rollback part program
Setup report schedule
Shut down system
Switch part program
View system logs
Designer Design inspection tree
- all Mechanic permissions, Enable defect database
plus:
Administrator Adjust date and time
- all Designer permissions, plus: Manage user accounts
Setup printer

Pressco Technician All Permissions

The following table provides a brief description of all the available permissions. Note
that some permissions may not be available in your list. The options that have been
permitted without login are removed from the list. For more information, refer to
Permission setup (on page 55).
Permission Description
Operator
Online (see "Online / Offline" Allows you to put a lane online.
on page 43)
Offline (see "Online / Offline" Allows you to put a lane offline.
on page 43)
Enable inspection items (see Allows you to enable or disable individual inspections and the
"Inspection menu" on page rejecter for those individual inspections.
165)
Open help sessions (see Allows you to start a remote help session with Pressco Technical
"Help - Remote Support" on Support.
page 122)
View change logs (see "Part Allows you to view the inspection change logs.
Program Change Log" on
page 168)

Mechanic
Access image tools (see Gives you access to the Image Analysis Tools.
"Image Analysis" on page 132)
Access system configuration Allows you to change system configuration values.
Access system diagnostics Allows you to perform system functions including I/O and
correlation diagnostics.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) User Accounts and Login Information 53
© 2011 Pressco Technology Inc. Proprietary
 Permission Description
Clear statistics Allows you to reset inspection statistics.
Configure alarms Allows you to configure the lane and sensor alarms.
Configure charts Allows you to configure trend charts and other statistics charts.
Configure walk-by (see "Walk Allows you to name, set up alarms, and set up which inspections
By Setup" on page 71) will be used with a particular region on a part. These regions are
displayed in the walk-by graphic.
Edit inspections Allows you to edit existing inspections.
Edit Lighting (see "Sensor Allows you to change the lighting settings for each camera.
menu" on page 129)
Forced Reject (on page 103) Allows you to request forced reject sampling.
Sampling
Rollback part program (see Allows you to roll the current part program back to a previous
"Part Program Change Log" state.
on page 168)
Setup report schedule (see Allows you to schedule statistics reports to be generated
"Schedule Reports" on page periodically.
88)
Shut down system (see Allows you to shut down the Intellispec system.
"Exiting the Intellispec
software" on page 43)
Switch part program Allows you to change the part program that the system is currently
running. This also allows you to add a new part program.
View system logs (see "Log Allows you to view the system logs.
Reader" on page 90)

Designer
Design inspection tree Allows you to add or delete inspections.
Enable defect database Not available as of this printing.

Administrator
Adjust date and time (see Allows you to adjust Intellispec system date and time.
"Adjusting Date and Time" on
page 119)
Manage user accounts (see Allows you to open Manage Users which lets you add, edit and
"Managing user accounts" on remove users.
page 47)
Setup printer (see "Setting up Allows you to configure a printer for Intellispec reports.
a printer" on page 120)

54 User Accounts and Login Information System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Permission setup
This feature allows you to set up permissions that will be available when no one is
logged in. It also gives the selected permissions to all users. Once a permission has been
selected, it will no longer appear in the available or selected columns when adding or
editing a user in the Manage Users option. This feature is only available to
Administrators (with Manage Users permissions).

To grant permissions to all users:

1. Log in as Administrator.
2. Click the Log in button with your name on it to see the Log in menu.
3. Select Manage Permissions. The Edit Permissions screen is displayed.
4. Click the Roles button.
5. From the drop-down menu below Roles, select "Not Logged In."
6. Highlight the desired permission in the left column.

7. Click the right arrow to move the permission to the right column.
8. Repeat the above two steps for all desired permissions.

9. Click the OK button to accept changes and exit.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) User Accounts and Login Information 55
© 2011 Pressco Technology Inc. Proprietary
 You can also remove permissions from all users that are assigned specific roles.

Caution
Be sure you select the User name from the drop-down menu before you change
Roles. Otherwise, you could change your Administrator permissions
(example: from Administrator to Operator, and not be able to Manage User
Permissions afterwards).

To remove permissions from a role:

1. Log in as Administrator.
2. Click the Log in button with your name on it to see the Log in menu.
3. Select Manage Permissions. The Edit Permissions screen is displayed.
4. Click the Roles button.
5. From the drop-down menu below Roles, select the role from which you want to
remove the permissions.
6. Highlight the desired permission in the right column.

7. Click the left arrow to move the permission to the left column.
8. Repeat the above two steps for all desired permissions.

9. Click the OK button to accept changes and exit.

You can also manage permissions for any user.
To edit a user's permissions:
1. Log in as Administrator.
2. Click the Log in button with your name on it to see the Log in menu.
3. Select Manage Permissions. The Edit Permissions screen is displayed.
4. Select a user from the User drop-down menu.
 Move the desired permissions between Denied and Granted. Or:
 Assign that user a new role. For example, change Jane's permissions from
Operator to Mechanic. The user will acquire all permissions for that role,
including any that you have assigned separately from Pressco's default settings.
5. Repeat the above step for all desired permissions.

6. Click the OK button to accept changes and exit.

AUTO LOGOUT SETUP

This feature will automatically log you out after a set number of minutes of inactivity.
To set up Auto Logout:
1. Log in as an administrative user.
2. Click the button with your user name to see the login drop-down menu.
3. Select Setup Auto Logout. The setup menu is displayed.
4. Click the box next to "Auto Logout" to enable the feature. A check mark is displayed
in the box when it is enabled.
5. Set the Wait time in minutes by clicking the up or down arrows, or by highlighting
the number of minutes and typing a new value (from 1 to 9999 minutes).

56 User Accounts and Login Information System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 6. Click the OK button . All users will be logged out automatically after the set
number of minutes of inactivity.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) User Accounts and Login Information 57
© 2011 Pressco Technology Inc. Proprietary
Chapter 7
GRAPHS AND IMAGE DISPLAYS
Several graphs are available on the user interface to help you view inspection trends.
This section discusses the buttons on the right side of the screen in the Lane Overview
and Sensor Overview modes.

TREND GRAPHS

To view the Lane trend graphs:

1. Select a lane (click a Lane n button).
2. Click the Trend Graphs button on the right side of the screen. The trend graph is
displayed.
Trend graphs are available to view statistics based on specified criteria. These graphs are
available for each lane and each sensor within that lane. You can select criteria for the
H-axis, the V-axis, and Series. There is an adjustable Alarm Level for Defect %. Both the
H-axis and V-axis adjust automatically to higher and lower values. The Alarm Level will
adjust as well. Below is a list of possible combinations for Time and Parts based graphs.
H-axis V-axis Series
Time Defect % Lane Total
Defect Count All Walk-By Groups
Defect Cost All Sensors
Parts and Defects Individual Sensors
Parts Defect % Lane Total
Defect Count All Walk-By Groups
Defect Cost All Sensors
Individual Sensors
For Trend Graphs, you can select which data to display. Select from the Series
drop-down menu.

Lane Total
Displays the statistics averaged for all sensors within the lane.
All Walk-By Groups
Displays the statistics for inspection groups. These groups are defined in the Walk
By Graphic setup, and pertain to a specific area of a part.
All Sensors
Displays the statistics for each sensor.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Graphs and Image Displays 59
© 2011 Pressco Technology Inc. Proprietary
 Individual Sensors [names vary]
Displays the statistics for only the selected sensor.
Note: A key (to explain color-coding and data point shape) is displayed to the right
of the graph for All Walk-By Groups and All Sensors.
To change the graph criteria:
1. Click any button (next to H-axis, V-axis, or Series) to view the drop-down menu
options.
2. Select the desired criteria. The graph is updated to display based on your chosen
criteria.
When the data falls outside of the current viewing range (example, time) a scroll button

becomes available next to the Series drop-down box.

To view other data:

1. Click the scroll button . A scroll bar becomes available.

2. Click and drag the scroll bar to view the desired data.

3. To exit, click the exit button . The graph returns to the current data.

Multiple Trend Graphs

In the Sensor Overview screen (on page 40), the upper and lower portions of the screen
can display different trend graphs. For example, you could display a time based graph at
the top of the screen, and a part based graph at the bottom of the screen. When the Trend
Graph button is available on the right side of the screen in multiple locations, you could
view any combination of trend graphs as you wish.

Trend Chart Configuration - System Overview

This is the setting for the trend chart displayed on System Overview screen.
 Note: the vertical axis setting is automatically scaled to best represent the data on
the chart.

To change the chart configuration:

1. Click the Home button to view the System Overview screen.

60 Graphs and Image Displays System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 2. Right-click over the trend chart. The Chart Configuration menu is displayed.

3. Choose from the available trend chart types, and select the number of points to
display on the chart.

4. Click the OK button to accept changes and exit the menu. The selected chart is
displayed in the System Overview screen.
 Note: these changes affect all trend charts in the System Overview screen

Trend Chart Configuration - Lane Overview

These settings affect the display of all the trend charts in the Lane Overview or Sensor
Overview screens.
 Note: the statistics for the lane are reset when you change a configuration setting.

To change the trend chart display:

1. View the Lane Overview or Sensor Overview screen by clicking either a Lane n
button or a Sensor n button.
2. Click one or all of the Trend Charts buttons on the right side of the screen to display
a trend chart.
3. Right-click over one of the trend charts. The Graph Menu is displayed.
4. From the Graph menu, select Configuration. The Trend Chart Configuration menu is
displayed.

5. Select the desired settings from all the available parameters.

6. Click the OK button to save your changes and exit the screen. All the trend charts for
the selected lane are updated to reflect your changes.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Graphs and Image Displays 61
© 2011 Pressco Technology Inc. Proprietary
 Alarm Percentages in Trend Charts
The alarm level can be adjusted when Defect % is selected for the V-axis. Click and drag
on the red Alarm Level line to adjust it. This also changes the alarm percentage in the
Alarm configuration menus (see "Lane Alarm Configuration" on page 78, "Sensor
Alarm Configuration" on page 81). The illustration below shows Sensor Overview mode
with Trend Charts displayed for both Lane and Sensor.
 Note: Changing this alarm percentage does not affect the alarm percentage level in
the Walk By Graphic.

MACHINE PART GRAPHS

Machine Part Graphs are available when you have the Correlation option installed.
Machine Parts Graphs display defect information for each machine part. Below is a list
of possible combinations for Defect % and Defect Count.
H-axis V-axis Series
Defect % Machine Parts Lane Total
All Sensors
Defect Count Machine Parts Lane Total

62 Graphs and Image Displays System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 All Sensors
An example graph is displayed below. It shows defects for a machine part type, and the
number of defects correlated to each sensor.

REJECT IMAGES

Reject Images are images from the last 100 parts that have failed. These images are
available in the Lane Overview screen and the Sensor Overview screen.
To view Reject Images:
1. From the System Overview screen, click a Lane n button to display lane information.
2. Click a Reject Images button on the right side of the screen. Note: there are buttons
for Lane and Sensor levels - these display images for the entire lane or just the
sensor.
Lane Reject Images show a variety of images from different Sensors. Below the
image is the name of the Sensor it came from and what time it was rejected. You can
scroll through the images using the arrows. Clicking on an image will bring you to
the Sensor from which it failed.

Sensor Reject Images show snapshots of failed images from that Sensor only.
Below the snapshot is the time it was rejected.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Graphs and Image Displays 63
© 2011 Pressco Technology Inc. Proprietary
 To use the images:
Click an image from the Lane Reject images to display the corresponding Sensor
information in the lower part of the screen.

Click any one of the small images to display a larger version of that image.
Click on the large image to display a magnified portion of the image. This is useful
to see small defects. Click and drag on the magnified portion to navigate around the
image. Click in the magnified area to toggle the magnifier.

64 Graphs and Image Displays System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Right-click [ ] on the image to choose a zoom amount. An enlarged image, the
same size as the Big Live Image (on page 73) is displayed. Use the navigation
arrows, or click and drag the cursor to pan around the image.
From the pop-up menu, you may also choose Image Analysis (on page 132) (when
the lane is offline).

Click the exit button to close the zoom window

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Graphs and Image Displays 65
© 2011 Pressco Technology Inc. Proprietary
 TIMING TREND

 Note: this chart is mostly used by Pressco service engineers during installation, or it
can be used when additional inspections or hardware have been added to the system.
This chart displays the time required to run inspections. It is important to view the
inspection timing, especially if you have multiple sensors or multiple lanes, to make sure
that the system is inspecting all parts before they reach the reject station.
The choices for the Series in the Timing Trend chart allow you to choose Sensor Total,
which is all inspections for that sensor, or any individual inspection for that sensor.

INSPECTIONS GRAPH

Click the Inspections button on the right side of the screen to see the Inspections Graph.
This graph displays the Defect Count or Defect % for the selected sensor. It displays the
failed inspections in descending order of failure. The example below is the graph shown
in Sensor Overview mode. In Lane Overview mode, the bars are displayed vertically
instead of horizontally.

66 Graphs and Image Displays System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 STATISTICS GRID

The Statistics Grid displays information about each Sensor. There are two different types
of Statistics Grids: Lane and Sensor.
Lane Statistics Grid
The Lane Statistics Grid (in Lane Overview mode) displays general information
about each Sensor. It shows the Total number of parts run, Sensor, Defects, Defect
%, Last N, and Last N %.

Sensor Statistics Grid

This grid is available when you display Sensor information. It shows specific
information for each sensor, including Inspection, Total number of parts run,
Defects, Defect %, Last N, and Last N %.

 Note: you can configure (see "Statistics Grid options" on page 69) the statistics
display. Your system may not display all of the above-mentioned items.
To display the statistics grid, click the Statistics button on the right side of the screen.
There may be multiple buttons, depending which screen you are viewing.
SORTING ORDER
To sort any column in ascending or descending order, click the button at the top of the
column. Click it again to toggle to the opposite order. Right-click to clear sorting in the
statistics grid.

Statistics Configuration
All the statistics grids in the current lane will use these settings.
To get to this screen:

1. From the Lane or Sensor Overview screen, click the Tools button to see the
Tools menu.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Graphs and Image Displays 67
© 2011 Pressco Technology Inc. Proprietary
 2. Choose Lane Setup, then Statistics Configuration.

Last N
Specify how many parts to include in recent statistics, such as the column "Last N"
which displays the number of defects in the Last N parts, or "Last N %" which
displays the percentages of defects within the Last N parts.
This feature allows you to continue to collect inspection data (Total inspected, total
defects, and defect %) without clearing the statistics to see how the most recent batch
of parts has done.
Parts per Update
Determines the graduations on the horizontal axis for the Trend Chart and Timing
Trend if "Parts" is selected.
Time per Update
Determines the graduations on the horizontal axis on the Trend Chart and Timing
Trend if "Time" is selected.

68 Graphs and Image Displays System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Statistics Grid options
To change what is displayed in the statistics grids, use the options menu. These settings
are applied to all statistics grids, whether in the Lane Overview screen, or Sensor
Overview screen. Right-click over any statistics grid to see the options. These are
explained below.

COLUMN VISIBILITY
Change the number of columns that are displayed in the grid.
DISPLAY OPTIONS
Change the number of rows that are displayed in the grid. This only affects the statistics
grids in the Sensor Overview level.
Hide Regions
If this is checked, then the inspection regions are not displayed in the grid. This
means the Ring, Polygon, Rectangle, or Adaptive regions that identify the inspection
area, but do not have any reject criteria.
Hide Enhancement
If this is checked, then the inspection enhancements such as Clipping, Stretch
Grayshades, or Power Filter are not displayed in the grid.
CHANGE LIMITS
This menu allows you to change the number of columns and rows of the grids in the first
two sections of the menu. These are the same as Column Visibility and Display Options.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Graphs and Image Displays 69
© 2011 Pressco Technology Inc. Proprietary
 The lower two sections of this menu allow you to enable and change limits for
inspection.
Use Error Limit
Causes the Defect % and Last N % columns to display in red if the trigger
percentage is exceeded. This allows you to see these statistics from a distance.
Use Warning Limit
Causes the Defect % and Last N % columns to display in yellow if the trigger
percentage is exceeded. This allows you to see these statistics from a distance.
CLEAR SORTING
Puts the sorting order back to the default setting. To sort any column in ascending or
descending order, click the button at the top of the column. Click it again to toggle to the
opposite order.

WALK BY GRAPHIC

This feature uses a graphic representation of a part so that you can quickly identify which
area of the part is failing. It is called Walk By because you can quickly walk by the
Intellispec and look at the graphic to determine the status of inspection:
Green areas indicate that parts are passing inspection.
Yellow warning areas notify you that the spoilage rate is approaching, but has not yet
reached a critical level. This allows you to make necessary changes to the
manufacturing process before the failure rate gets too high.
Red areas indicate the spoilage rate has exceeded user defined limits.
The defect percentage rate at which each group reaches warning or failure limits is
defined in Walk By Setup (on page 71).
There are two available Walk By Graphics:
A small Walk By Graphic is displayed in System Overview, Lane Overview, and
Sensor Overview modes
A large Walk By Graphic can be displayed in Lane Overview mode
To see the large Walk By Graphic:
1. Click a Lane n button to view the Lane Overview mode.

2. Click the More Lane Information bar in the center of the screen to display more
graph options.

3. Click the Walk By button on the right side of the screen.

The Walk By Graphic is displayed in the center of the screen.

70 Graphs and Image Displays System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 The large Walk By Graphic displays the group names, pointing to the appropriate areas
on the part. It also displays the current defect percentage for each of those groups, from
inspection results.

Using the Walk By Graphic

You can view inspection information by clicking on the areas of the graphic. The
Intellispec will display the configured inspection group and detail. The example below
shows:
The Panel group was clicked - all the inspections for Panel are displayed in the table
The Panel area in the Walk By Graphic is red - The average defect % for the group
of inspections exceeds the failure limit from the Walk By setup (on page 71)

Double-click an inspection from the table (example: a Contrast inspection) to open and
edit that inspection. Note: Some menu items are only available to advanced level users.

Walk By Setup
This screen allows you to set up the Walk By Image. Each Lane can be set up differently
if needed.
Each area of the part graphic display is:
Assigned a group name.
Assigned the correct inspections for that group.
Configured to turn the area yellow or red when defined defect statistics are achieved.
 Note: you must have correct user permissions to set up the Walk By Graphic. You
must also have a part program loaded.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Graphs and Image Displays 71
© 2011 Pressco Technology Inc. Proprietary
 To get to this screen:

From the Lane or Sensor Overview screen, click the Tools button to see the
Tools menu > Lane set up > Walk By Setup.

To set up the Walk By graphic:

1. Follow the instructions on screen, and navigate using the buttons at the bottom of the
screen. Some parameters are explained below.
2. After the last screen, the system takes you back to the first screen so that you can set

up another group. If you are finished, click the OK button at the bottom of the
screen to accept your changes and exit the screen.
Group
Each graphical area on the part is assigned to a group - this is defined in the graphic
file. Assign as many inspections as you wish to a group, preferably those inspecting
that area of the part. Some drop-down menus on the user interface refer to 'groups' -
these represent groups of inspections that inspect one area of a part.
A group can be a contiguous area, or a group of related areas on a part, as shown in
red below.

72 Graphs and Image Displays System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Warning Percent
Set the value at which the group on the Walk By Graphic turns yellow. Yellow
warning areas notify you that the spoilage rate is approaching, but has not yet
reached a critical level. This allows you to make necessary changes to the
manufacturing process before the failure rate gets too high.
Note: this warning percentage is not connected to inspection warning limits.
Those limits are set separately. Additionally, this warning percentage does not
affect the Excessive Warnings alarm.
Failure Percent
Set the value at which the group on the Walk By Graphic turns red. Red areas
indicate the spoilage rate has exceeded user defined limits.
Note: this failure percentage is not connected to inspection limits. Those limits
are set separately. Additionally, this failure percentage does not affect the rejects
alarms.
Group Digital Outputs (for Extended I/O option)
Select the group number (Group 0 through 15) to trigger an output signal through the
Extended I/O (see "Extended I/O board" on page 321) board.

The outputs go active when any inspection within the assigned group fails. You can
use these outputs to monitor the process within your plant and make adjustments as
necessary.
You can assign multiple groups to one output, even groups from other lanes.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Graphs and Image Displays 73
© 2011 Pressco Technology Inc. Proprietary
 BIG LIVE IMAGE

Click the Big Live Image button in Sensor Overview mode to view an enlarged image of
the last part that was inspected.
This image is updated when the lane is online and the camera is snapping images. The
image is outlined in green if the part is passing, yellow if it is in a warning state, or red if
the part is failing. You can view this image from a distance to quickly see how the
inspection process is performing.

74 Graphs and Image Displays System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
Chapter 8
ALARMS
There are three levels of alarms within the Intellispec system: System, Lane, and Sensor
alarms. Most of these are configurable. The table below lists the alarms, possible causes
for triggering the alarm, the reset mechanism, and color of the indicator on the light tree.
Also refer to the light tree status (on page 285) for more information about the lights.
 Note: Alarms are recorded in the system log reader (on page 90), even when the
alarms are automatically cleared.

Alarm Name Cause Reset Mechanism Color in light

tree
System Alarms
Note: If a system alarm occurs, an alarm icon is displayed in the lower right of the screen (in the Windows
system tray)
UPS Battery is dead. Manually [you must Not applicable
Or: first replace battery] (N/A)

Plant power is lost and the UPS If plant power is N/A

shutdown time is exceeded. The restored before the
Intellispec shuts down. Intellispec shuts down,
then the alarm
condition is
automatically cleared.
Otherwise, you must
restart the system
manually.
Over temperature CPU temperature exceeds highest Manually N/A
recommended operating temperature.
The Intellispec system shuts down. You
must wait till the processor cools before
resuming operation.
Lost network If the plant network is configured to Restoring plant N/A
connection communicate with the Intellispec and network connection
the network connection is lost, a lost
network icon appears in the Windows
system tray

Lane Alarms
Percent Defects¹ Percentage of defects exceeds the set Manually Red
limit
System Status¹ Lane goes offline Manually Green On
when online
Green Off
when offline

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Alarms 75
© 2011 Pressco Technology Inc. Proprietary
Alarm Name Cause Reset Mechanism Color in light
tree
Chute Full¹ Reject chute is full Manually [you must Red
first clear chute]
Blow Molder Door Blow molder door is open Automatically [by Red
Open¹ closing blow molder
door]
Power Status¹ Lane AC Power is lost Automatically Off when AC
power is lost
Blue when
power is OK
Good Parts¹ Used as a part counter. When specified Manually Red
number of parts is reached, then alarm
is triggered.
Missed Rejects¹ System missed a reject Manually Red

Sensor Alarms
Percent Rejects¹ Percentage of rejected parts exceeds Manually Red
the set limit
Excessive Rejects¹ Excessive number of rejects Manually Red
Excessive Warnings¹ Excessive number of warnings Manually Amber
Consecutive Defects¹ Too many consecutive defects Manually Red
Missed Part¹ System missed a part Manually Red
Missed Result¹ System missed a result Manually Red
¹ If you want to connect an external monitoring device such as a PLC, an optional
Extended I/O (on page 321) board is required for each lane.

VIEWING AND CLEARING ALARMS

Use the View/Clear Alarms menu to see which alarms are enabled and disabled. A green
light indicates that the alarm has not been triggered, while a red light indicates the alarm
has been triggered.
To get to the View/Clear Alarms menu:

Click an Alarm button . The View/Clear

Alarms menu is displayed.
Or:
1. View the Lane Overview or Sensor Overview screen by clicking either a Lane n
button or Sensor button.

2. Click the Alarms button to view the Alarms menu.

3. Select View/Clear Alarms from the menu. The menu shown below is displayed.

76 Alarms System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 To clear an alarm:
Click the Clear button next to any alarm to clear a single alarm. Or:
Click the Clear All button at the bottom of the screen to clear all alarms.
 Note: some triggered alarms may be from another sensor - click the red sensor
indicator [in item 1] to see that sensor's alarms

1 List of sensors in the selected lane

2 List of Lane alarms
3 List of Sensor alarms. Use the drop-down menu to select a sensor.

The indicators in this screen show whether an alarm is enabled, and whether it is
triggered.
Green Off - the alarm is not enabled nor triggered

Green On - the alarm is enabled, but has not been triggered

Red Off - the alarm is not enabled, but the values would trigger the alarm

Red On - the alarm is both enabled and triggered

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Alarms 77
© 2011 Pressco Technology Inc. Proprietary
 SYSTEM ALARMS
The system alarms are the UPS (uninterruptible power supply) and CPU temperature
alarms. You can configure the UPS shut down time.
To get to this menu:

1. Click the Home button to view the System Overview screen.

2. Click the Alarms button to view the system alarms. The screen shown
below is displayed.

1 UPS Shutdown Time – Set the number of seconds that the UPS will maintain power to the
system if AC power has been lost. The Intellispec system shuts down after this time period.
This allows for a normal Windows shutdown.
2 CPU Temperature – Displays the current, warning, and shutdown temperatures associated
with the computer CPU. If a multiple core computer is used, the highest temperature is
displayed. If the shutdown CPU temperature is reached, the Intellispec system shuts down.

LANE ALARM CONFIGURATION

In the Lane Alarm Configuration pop-up menu, you can edit alarms for an entire lane.
 Note: Some menu items are only available to advanced level users.

To get to this menu:

1. Log in.
2. View the Lane Overview screen by clicking a Lane n button.

3. Click the Alarms button to view the Alarms menu.

78 Alarms System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 4. From the Alarms menu, select Lane Alarm Configuration.

Select an alarm from the drop-down menu to configure that alarm. You can enable or
disable parameters for each alarm individually. A check mark appears in the box next to
the parameter when it is enabled. The parameters are described next:
Alarm Enabled
Enables alarm.
Percent Trigger
Define the percentage of parts inspected that must fail to trigger the total percent
defects alarm. This number is selectable between zero and 100. The default value is
five percent.
Percent Trigger is used in the Percent Defects alarm.
Note: you can change this percentage in the Trend Charts (see "Alarm
Percentages in Trend Charts" on page 62) in Lane Overview mode when
Defect % is selected for the V-axis.
Trigger (thousands)
[Good Parts alarm] The number of parts that must pass inspection to trigger the
alarm. The number is expressed in thousands.
Audible Enabled
If this parameter is enabled, the audible alarm will sound when triggered.
Audible Duration
The number of seconds the audible alarm will sound if triggered. A value of zero
indicates an infinite duration, until the system goes back online. Or, use the slider to
set values up to 3600 seconds (60 minutes).
Visual Enabled
If this parameter is enabled, this alarm will switch on the appropriate light on the
light tree when triggered.
Visual Duration
The number of seconds the light will remain on when the alarm is triggered. A value
of zero indicates an infinite duration. Or, you can enter values up to 3600 seconds
(60 minutes).
System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Alarms 79
© 2011 Pressco Technology Inc. Proprietary
 Alarm Outputs
Select an output (Inspection Alarm 0-15) to be toggled on the optional Extended I/O
(see "Extended I/O board" on page 321) kit when the alarm is triggered.
 There are 16 available Inspection Alarm outputs that correspond to the
extended I/O signals (on page 322). Click one of the output numbers to assign
the current alarm to an output.
 These outputs go active when the alarm is triggered, and go inactive when the
alarm is cleared.
 The outputs can be monitored by your plant equipment, such as a PLC, to notify
you when certain alarms are triggered.
Disable All Alarms
Click this button to disable all the current alarms at once. This disables only the
alarms for the current sensor or lane. This is used in emergencies when you cannot
repair a situation immediately, or when setting up the system. The remaining
parameter settings for each alarm are saved for future use. You must re-enable each
alarm individually when you are ready.

Click the OK button to apply changes and exit the menu.

Lane alarms description

The available Lane alarms are as follows:
Percent Defects
This alarm is triggered when the percentage of defective parts from a Lane exceeds
the Percent Trigger. It will remain triggered until you clear the alarm. It uses the red
light of the light tree as a visual indicator.
System Status
This alarm indicates whether the system is online or offline. It uses the green light of
the light tree as a visual indicator. The green light turns on when the system is online,
and turns off when the system goes offline.
Chute Full
This alarm is mainly used in systems that have inspection modules installed within a
blow molder, and use the blow molder‘s internal reject chute. It is triggered when the
blow molder‘s internal reject chute is full. This alarm may not apply to your system.
It uses the red light of the light tree as a visual indicator.
If this alarm is enabled and triggered, the blow molder‘s internal rejector will be
disabled, thus not allowing any more defective parts to be rejected. The rejector will
remain disabled until you clear the chute and then clear the alarm from the alarms
tab. If you clear the alarm without clearing the chute, the alarm will be triggered
again.
Note: This alarm is disabled when the Intellispec is offline.
Blow Molder Door Open
This alarm is used for systems that have inspection modules installed within a blow
molder. It is triggered when the blow molder door is opened. It will remain triggered
until the door is closed. It uses the red light of the light tree as a visual indicator. This
alarm may not apply to your system.
Note: In PET Preform applications, this alarm is triggered when the Bypass
Gate opens.
80 Alarms System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Power Status
This alarm is triggered when Lane AC power is lost. It remains triggered until AC
power is restored. If AC power remains off for an extended period of time, the
system will shut down.
The red light of the light tree will switch on when Lane AC power is lost. The blue
light should remain on as long as the Lane power is on.
Good Parts
This alarm can be used as a part counter. For example, say you are inspecting
preforms, and have a box at the end of the conveyor (after inspection) that holds
5000 preforms. This alarm will count the number of good inspected parts, and notify
you when 5000 good parts have reached that box. The Alarm Output through the
optional Extended I/O can be used to stop the conveyor from moving parts into the
inspection system. You can then install a new box at the end of the conveyor, reset
this alarm, and start counting the next 5000 parts.
This alarm is triggered when a number of good inspected parts [Trigger (thousands)]
has been reached. It will remain triggered until you clear the alarm. It uses the red
light of the light tree as a visual indicator. Note that clearing this alarm also clears
the Good Parts count.
See also information about the optional Extended I/O (see "Extended I/O board" on
page 321) module.
Missed Reject
This alarm works in conjunction with Reject Confirm (see "Reject Confirm
Calibration" on page 116). It is triggered when a missed reject occurs. It uses the red
light of the light tree as a visual indicator.
There will be two Missed Reject alarms available if two rejectors (see "Rejector
Enable/ Disable" on page 101) are enabled and two Reject Confirm rejectors (see
"Reject Confirm Calibration" on page 116) are enabled.

SENSOR ALARM CONFIGURATION

In the Sensor Alarm Configuration pop up window, you can edit alarm settings for an
entire Sensor.
 Note: Some menu items are only available to advanced level users.

To get to this menu:

1. Log in.
2. View either the Lane Overview or Sensor Overview screen by clicking a Lane n or
Sensor n button.

3. Click the Alarms button to view the Alarms menu.

4. From the Alarms menu, select Sensor Alarm Configuration.
5. Choose a sensor to configure. You must configure each sensor separately.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Alarms 81
© 2011 Pressco Technology Inc. Proprietary
 6. Select an alarm from the drop-down menu to configure that alarm. You can enable or
disable parameters for each alarm individually. A check mark appears in the box next
to the parameter when it is enabled. The parameters are described below.

Alarm Enabled
Enables alarm.
Sample Size
Define the number of parts that must be inspected to determine the excessive
warning percentage. This number is selectable between zero and 10,000. The default
value is 100. This is a sliding window: for example assume Sample Size = 1,000 and
Percent Trigger = 3. If three percent of the last 1000 parts have had a warning status,
the alarm is triggered.
Sample Size is used in the Excessive Rejects and Excessive Warnings alarms.
Percent Trigger
Define the percentage of parts inspected that must fail to trigger the total percent
defects alarm. This number is selectable between zero and 100. The default value is
five percent.
Percent Trigger is used in the Percent Rejects alarm, Excessive Rejects, and
Excessive Warnings alarms.

 Note: you can change this percentage in the Trend Charts (see "Alarm
Percentages in Trend Charts" on page 62) in Sensor Overview mode when Defect
% is selected for the V-axis.

Consecutive Trigger
Define the number of defects in a row that the system must have to trigger the alarm.
This number is selectable between zero and 340,000. The default value is 25. If this
parameter is set to zero, the alarm is disabled.
Audible Enabled
If this parameter is enabled, the audible alarm will sound when triggered.

82 Alarms System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Audible Duration
The number of seconds the audible alarm will sound if triggered. A value of zero
indicates an infinite duration, until the system goes back online. Or, use the slider to
set values up to 3600 seconds (60 minutes).
Visual Enabled
If this parameter is enabled, this alarm will switch on the appropriate light on the
light tree when triggered.
Visual Duration
The number of seconds the light will remain on when the alarm is triggered. A value
of zero indicates an infinite duration. Or, you can enter values up to 3600 seconds
(60 minutes).
Alarm Outputs
Select an output (Inspection Alarm 0-15) to be toggled on the optional Extended I/O
(see "Extended I/O board" on page 321) kit when the alarm is triggered.
 There are 16 available Inspection Alarm outputs that correspond to the
extended I/O signals (on page 322). Click one of the output numbers to assign
the current alarm to an output.
 These outputs go active when the alarm is triggered, and go inactive when the
alarm is cleared.
 The outputs can be monitored by your plant equipment, such as a PLC, to notify
you when certain alarms are triggered.
Disable All Alarms
Click this button to disable all the current alarms at once. This disables only the
alarms for the current sensor or lane. This is used in emergencies when you cannot
repair a situation immediately, or when setting up the system. The remaining
parameter settings for each alarm are saved for future use. You must re-enable each
alarm individually when you are ready.

Click the OK button to apply changes and exit the menu.

Sensor alarms description

The available Sensor alarms are as follows:
 Note: parameters, such as Percent Trigger, are adjusted in the Sensor Alarm
Configuration (on page 81).

Percent Rejects
This alarm is triggered when the total percentage of defects for the current sensor
exceeds a defined percentage. This percentage is defined with the Percent Trigger
parameter. It will remain triggered until you clear the alarm. It uses the red light of
the light tree as a visual indicator.
Excessive Rejects
This alarm is triggered when a percentage of the last n parts have been found
defective. It will remain triggered until you clear the alarm. n = Sample Size. The
percentage is defined with the Percent Trigger parameter. It uses the red light of the
light tree as a visual indicator.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Alarms 83
© 2011 Pressco Technology Inc. Proprietary
 Excessive Warnings
This alarm is triggered when a percentage of the last n parts have been found with a
warning status. It will remain triggered until you clear the alarm. n = Sample Size.
The percentage is defined with the Percent Trigger parameter. It uses the amber light
of the light tree as a visual indicator.
Warnings are enabled in the Retro-Spec Options (on page 181) when you are editing
an inspection.
Consecutive Defects
This alarm is triggered when the sensor has had too many consecutive defects. The
number of defects is defined by the Consecutive Trigger parameter. It will remain
triggered until you clear the alarm. It uses the red light of the light tree as a visual
indicator.
Missed Part
This alarm is triggered if the sensor misses a part present signal. It will remain
triggered until you clear the alarm. It uses the red light of the light tree as a visual
indicator.
See also Sequence of Events (see "Sequence of Events During Inspection" on page
162) and Part Present Delay Calibration (on page 109)
Missed Result
This alarm is triggered if the sensor misses the inspection results of a part. For
example, the inspection time was too high, or the processor was too busy to process
the inspection results before the part reached the reject position. It will remain
triggered until you clear the alarm. It uses the red light of the light tree as a visual
indicator.
See also Sequence of Events (see "Sequence of Events During Inspection" on page
162).

84 Alarms System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
Chapter 9
TOOLS MENUS
This section covers the tools menus that are available through System Overview or
Lane/Sensor Overview modes.

TOOLS MENU - SYSTEM OVERVIEW SCREEN

To view the Tools menu:
1. Log in. (Some items may be grayed out if you do not have permissions to use the
items)

2. Click the Home button to view the System Overview screen.

3. Click the Tools button to view the Tools menu.

1 Log Reader (on page 90) – Open the Intellispec log

2 Reset System Statistics – Reset the entire system statistics (all Lanes) at
once
3 Disk Imaging Software – Open Acronis Echo software for backing up
system hard drive
4 CPU Temperature – Displays the current, warning, and shutdown
temperatures associated with the computer CPU. If a multiple core
computer is used, the highest temperature is displayed. If the shutdown
CPU temperature is reached, the Intellispec system shuts down.
5 UPS Information – Display Uninterruptible Power Supply (UPS)
information and settings
6 Chart Configuration – Choose the Trend Graph Type and the number of
divisions for the horizontal axis for the chart displayed in the System
Overview Screen
System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Tools Menus 85
© 2011 Pressco Technology Inc. Proprietary
 7 Defect Database - not available as of this publication
8 System - Set system date and time or set up a printer
9 Exit System – Shut down Intellispec software

TOOLS MENU - LANE OVERVIEW AND

SENSOR OVERVIEWS SCREENS
The Tools menu is the same in both Lane Overview and Sensor Overview screens.
To view the Tools menu:
1. Log in. (Some items may be grayed out if you do not have permissions to use the
items)
2. Click a Lane n button to view the Lane Overview screen.

3. Click the Tools button to view the Tools menu.

Reporting
The Intellispec generates many different reports to provide inspection detail. Many of
these reports can be transferred outside of the Intellispec.
 Note: Some menu items are only available to advanced level users.

To view reports:
1. View the Lane Overview screen by clicking a Lane n button.

2. Click the System Configuration button to view the Tools menu.

3. From the Tools menu select Reporting, then select your desired option. These are
described below.

1 Lane Summary Report (on page 87) - Generate a summary of the

statistics for the current lane.
2 Lane Detail Report (on page 88) - Generate a report with the lane and
sensor defect statistics broken down to inspection-by-inspection data.

86 Tools Menus System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 3 Schedule Reports (on page 88) - Define the frequency and destination for
automatic statistics reporting.
4 Log Reader (on page 90) – Open the Intellispec log
5 Sensor Missed Statistics (on page 90) - Display the number of missed
parts for the lane.

Lane Summary Report

This report lists the statistics summary for the lane, including:
Number of parts inspected
Number of defects
Defect percentage
The above numbers are reported per sensor, and as an overall number for the lane. An
example from a one lane system is shown below.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Tools Menus 87
© 2011 Pressco Technology Inc. Proprietary
 Lane Detail Report
This report contains all the information in the Lane Summary Report (on page 87), plus
inspection detail for each sensor with the number of defects found by each inspection. An
example is shown below.

Schedule Reports
Set up a schedule where the Intellispec generates reports automatically. This is a
Lane-level setting. To schedule reports for more than one lane, you must repeat the
process for each lane.
To schedule reports:
1. Go to the Lane Overview screen by clicking a Lane n button.

2. Click the Configuration button to view the Tools menu.

3. From the Tools menu, select Reporting, then select Schedule Reports. The screen
shown below is displayed.
4. Change the settings as desired. These are described below.
88 Tools Menus System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 5. Click the OK button to save changes and exit the screen.

REPORT DROP-DOWN MENU

Select which report to schedule, then change the settings in the menu. Each report must
be set up separately.
See also Lane Summary Report (on page 87) and Lane Detail Report (on page 88).
REPORT SETTINGS
Enable Scheduled Report
Choose whether to schedule the selected report. When this box is checked, the
settings below are active.
Destination drop-down menu
Choose whether to send the report to the default printer or a file. When Text File is
selected, you can enter a file name by clicking the File Name button.
If you do not name the file, then the file is named "PresscoReportnn.txt" where nn is
the number of the next generated report. It is saved at the hard disk location
"c:\Pressco." Subsequently saved reports overwrite the file.
Keep File Name
When a report is printed to file and this feature is enabled, the system will write the
inspection statistics to the same file name each time, rather than creating new files
with unique names. The system overwrites the file each time. You will need to click
the File Name button, browse to the location where you want to save it, and create a
name for your report.
An example of where this feature might be used is a plant where the Intellispec is
networked. Say the office computer is programmed to poll the Intellispec at regular
intervals to get the latest statistics report. With the same file name, the office
computer just needs to request the same file name each time, regardless of the date
and time the report was saved.
Reset Statistics
The Lane statistics are cleared after each print.
Next Scheduled Report
Using a 24 hour clock, set the time when the Intellispec should save or print the next
report.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Tools Menus 89
© 2011 Pressco Technology Inc. Proprietary
 Time Between Reports
Set the time interval when the Intellispec should save or print the following reports.
This interval is used after the Next Scheduled Report, and is repeated the set number
of hours thereafter.

Log Reader
The log reader displays the Intellispec event history including:
User log in and log out information
Part program changes
Note: detailed part program changes are found in the Part Program Change
Log (on page 168)
Alarms, when triggered and cleared
System errors
System starting information
Lane online/ offline history
Lighting changes
Text files of the logs are stored at: C:\Pressco\Logs.

Sensor Missed Statistics

Displays the number of missed parts and missed part tracking for the sensor.

This information is recorded in the Log Reader (on page 90).

90 Tools Menus System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Missed Results
This can occur if you set the Reject Delay Calibration (on page 111) incorrectly.
Another cause could be kinks or intermittent connections to cables, or the inspection
time for the lane is too long.

ERROR MESSAGES
Part Tracker Exception
If you see an error "Part Tracker Exception" on the Intellispec screen, this means that
power was lost to the Cluster Box or Part Tracker.
To reset the part tracker board:
Push the Reset button on the part tracker board. This is found inside the inspection
module or Cluster Box.
Lost Part Tracking
If you see a "Lost Part Tracking" message, possibly the power was lost to the Cluster
Box or Part Tracker inside an inspection module. Reset the Part Tracker board as
described above.

Part Setup
The Part Setup menu provides access to lighting, part display options in charts, and part
width calibration.
To view the Part Setup menu:
1. View the Lane Overview screen by clicking a Lane n button.

2. Click the System Configuration button to view the Tools menu.

3. From the Tools menu select Part Setup >> then your desired option. These are
described below.
Some menu items are only available to advanced level users.

1 Advanced Adjust Lighting (on page 135)

2 Basic Adjust Lighting (on page 135)
3 Clear All Defect Images - Remove all images from the Reject Images
buffer.
4 Change Part Type - Select the type of part to be displayed on the Walk By
Graphic for the current lane.
5 Set Cost Per Part - Set the cost of each product, to be used with the
"Defect Cost" trend chart.
6 Image Analysis (on page 132) - Determine the gray shade value for any
pixel or group of pixels in your image.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Tools Menus 91
© 2011 Pressco Technology Inc. Proprietary
 7 Part Width Calibration (on page 92) - Set the number of encoder pulses
that the part detect sensor "sees" the part.
8 Select Inspections For Charts - Select which inspections (up to 8) to
display on the Trend Chart and Timing Trend.
9 Select Measurements for SPC - not currently used.

Part Width Calibration

Part Width is the number of encoder pulses that the part detect sensor "sees" the part. For
an illustration of Part Width within the inspection process, refer to the sequence of
events (see "Sequence of Events During Inspection" on page 162).
To perform the calibration you must be running parts past the part detect sensor.
To get to the Part Width menu:
1. From the Sensor Overview mode, right-click on a sensor button to view the sensor
menu (on page 129).
2. Select Part Tracking, then select Part Width Calibration.

To calibrate the Part Width:

1. With parts running under the camera, click Start Calibration. As each part goes by
its part width will be displayed in the window next to the Start button.
2. After a sufficient number of parts have gone by (we recommend about 10 parts),
click Stop Calibration (same button as Start Calibration). This will display the
calibration results (shown above right).
3. Examine the results; look for the minimum and maximum values to be within
approximately 10 encoder pulses of each other. If the results are acceptable click OK

to save the data. If the results are skewed click the button and recalibrate.

Part Rate
In Intellispec systems with software version 5.0.440 and later, the part rate is displayed in
Lane Overview and Sensor Overview modes.
The part rate displays:
a. ppm (parts per minute) - The average rate over the last five seconds. It is updated once per
second.
92 Tools Menus System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 b. max - The maximum rate found for all individual parts in the last five seconds determined
in [a]. The displayed value is the largest value found in the last five minutes.

Lane Setup
Some menu items are only available to advanced level users.

1 Chart Configuration – Set the number of columns in the Trend Chart and
the currency type to be used in the "Cost per Part" trend chart.
2 Change Lane Name - Change the name of the current lane.
3 Change Sensor Name - Change the name of the selected sensor.
4 Image Display Configuration (on page 94) - Set the frequency, rotation,
and other display options for the sensor images.
5 Machine Part Correlation (on page 95) - Configure up to four different
machine parts for correlation. (This is usually done by the Pressco
installer)
6 Manage Part Programs (on page 97) - Create, delete, or edit part
programs.
7 Miscellaneous Configuration (on page 100) - Change settings for
Missed Results, Inspection Warnings, and Defect Database (not currently
available).
8 Rejector Enable/ Disable (on page 101) - Enable or disable the rejector
for lane or sensors.
9 Image Source (on page 139) - Select images to display on the lane.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Tools Menus 93
© 2011 Pressco Technology Inc. Proprietary
 10 Start Forced Reject (on page 103) - Force parts to be rejected based on
and correlation to a specific machine part.
13 Stop Forced Reject - Stop the Forced Reject process.
11 Statistics Configuration (on page 67) - Change the display settings for
the charts displayed by the Statistics buttons.
12 Statistics Grid Configuration (on page 105) - Change the amount of
information for the charts displayed by the Statistics buttons.
14 Walk By Setup (on page 71) - Set up the group names, inspections
assigned to each group, and the criteria determining when the areas of the
graphic turn green, yellow, or red.

Image Display Configuration

Adjust the display settings for images.
To get to this screen:

From the Lane or Sensor Overview screen, click the Tools button to see the
Tools menu, then select Lane Setup, then select Image Display Configuration.

1 Set the frequency to update the image in the sensor view window.
2 If correlation is used, check this box to display correlation information in
the Big Live Image view.
3 Rotate the defect images, sensor display images (heartbeat), and the Big
Live Images by selecting rotation in degrees with respect to camera
position, or rotation with respect to the orientation (if an orientation is being
used).

94 Tools Menus System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Machine Part Correlation
Configure up to four different machine parts for correlation. Each machine part can be
named and assigned the correct number of stations. The offset bar is used for calibrating
the displayed part with the actual machine part.
 Note: This screen is usually set up by the Pressco installer.

To get to this screen:

From the Lane or Sensor overview screen, click the Tools button to see the
Tools menu, then select Lane Setup, then select Machine Part Correlation.

Number Of Machine Parts

Select the number of correlation sensors in your system (1-4).

 Note: If you only see two Machine Parts available, you may have a two channel Part
Tracker board. This is the default configuration.
 If your system has an eight channel part tracker board, you must run the Discovery
software and configure the lane for an eight channel part tracker board. Use the Edit
Existing Lane function. This will provide the capacity for four Machine Parts to be
configured.

Name
Rename each machine part to something more recognizable to you (examples:
Cavity, Spindle, or Liner Gun #1). This name will be displayed on the Intellispec
screens and throughout correlation reports.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Tools Menus 95
© 2011 Pressco Technology Inc. Proprietary
 Source
Select between Hardware and Part Program to provide correlation. Some
applications have inspections from which you can derive correlation information.
Number
Set the number of components in each machine part (example, number of pockets in
a starwheel).
Offset
This allows you to change the mapping between what the inspection system
considers part #1 (or pocket #1) and the actual parts. For example, if you try to reject
a part from cavity #1, and the system rejects the part from cavity #2, then you would
set offset at 1. This information is required to be correct for the inspection system to
track components properly.
Outfeed Transfer Sequential
(only available when four sensors are used, and only applicable to blow molder
installations) Specify whether the infeed and outfeed transfer arms are numbered
Independently or Sequentially. For example, say your machine has 10 infeed transfer
arms and 10 outfeed transfer arms. If they are numbered Independently, the infeed
transfer arms would be numbered 1 - 10, and the outfeed transfer arms would be
numbered 1 - 10 as well. If they are numbered Sequentially, the infeed transfer arms
would be numbered 1 - 10, and the outfeed transfer arms would be numbered 11 - 20.
Outfeed Linked to Infeed (MP4 to MP3)
(applicable to blow molder installations) Enable this to derive the outfeed correlation
count (MP4) from the infeed correlation count (MP3). This is typical of most blow
molders. For example, in an SBO20 machine, the infeed count will be from 1 - 10.
The outfeed count will be from 11 - 20. Infeed count 1 will correspond to outfeed 11,
and so forth.
Note: When this feature is enabled, the number of components is forced to be
equal (number of components in MP3 = number of components in MP4 ).
Note: There is no index sensor for MP4 in the hardware configuration.
Dual Cavity System
(only available when four sensors are used, and only applicable to blow molder
installations) Enable this if your system is a dual cavity machine.

96 Tools Menus System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Show correlation values in images
Displays the correlation value in the images. These values are saved as part of the
image file (if you save images).

Manage Part Programs

Create new part programs or delete, edit, rename, import or export existing part programs
for all the different products inspected with the system.
To get to this screen:

From the Lane or Sensor Overview screen, click the Tools button to see the
Tools menu, then select Lane Setup, then select Manage Part Programs. Or:
Right-click the Part Program drop-down menu.

For information on using this screen see:

How to Create, Copy, or Import a Part Program (on page 162)
Export a part program (on page 99)
Load a Part Program (on page 98)

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Tools Menus 97
© 2011 Pressco Technology Inc. Proprietary
 DELETE A PART PROGRAM
You can delete a part program to prevent other users from running it.
To delete a part program:
1. Go to a Lane Overview or Sensor Overview screen [from Home: Lane button >
Sensor button].
2. Load a known good part program, one that you will not delete. You cannot delete the
currently running part program.
3. Right-click over the part program drop-down menu. The Manage Part Programs
menu is displayed.
4. Highlight the program name in the Manage Part Programs menu, then click the
Delete button.
5. A warning box will ask you if you are sure you want to delete the program. Click the

OK button to delete the program. The program is deleted from memory.

Right-click

LOAD A PART PROGRAM

You can switch part programs by loading a different part program from disk.
To load a part program:
1. Go to a Lane Overview or Sensor Overview screen [from Home: Lane button >
Sensor button].
2. Right-click over the part program drop-down menu. The Manage Part Programs
menu is displayed.
3. Highlight the program name in the Manage Part Programs menu, then click the Load
button. The program name will appear in the Part Program drop-down menu on the
Lane Overview or Sensor Overview screen.

4. Click the OK button to exit the Manage Part Programs menu. The new part
program is loaded into the Intellispec memory.

98 Tools Menus System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Right-click

EXPORT A PART PROGRAM

You can export a part program to use it on another sensor, lane, or Intellispec.

Right-click

To export a part program:

1. Go to a Lane Overview or Sensor Overview screen [from Home: Lane button >
Sensor button].
2. Right-click over the part program drop-down menu. The Manage Part Programs
menu is displayed.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Tools Menus 99
© 2011 Pressco Technology Inc. Proprietary
 3. Click the Import/Export button. The Import or Export Part Programs menu is
displayed.

4. Click the disk icon to browse to the folder or USB destination to export the part
program.
5. Highlight the part program that you want to export in the Current Part Programs
column.

6. Click the right arrow button to export the part program.

7. Click the OK button to exit the Import or Export Part Programs menu. The part
program is exported.

8. Click the OK button to exit the Manage Part Programs menu.

100 Tools Menus System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Miscellaneous Configuration
Enable or disable additional lane options.
To get to this screen:

From the Lane or Sensor Overview screen, click the Tools button to see the
Tools menu, then select Lane Setup, then select Miscellaneous Configuration.

Reject Missed Results

A missed result occurs if the system misses the inspection results of a part. This can
happen if the inspection time is too long or if the system is too busy to process all the
data before the part reaches the reject station.
Check this box if you want the system to reject parts from any missed results in the
current Lane.
Disable Inspection Warnings
Inspections can have reject and/or warning limits. A warning allows you to perform
maintenance or adjustments before the system starts rejecting parts.
The warning limits are represented by the yellow adjustable slider bar on the
Retro-Spec graphs. If you do not wish to use warning limits, check the Disable
Inspection Warnings box.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Tools Menus 101
© 2011 Pressco Technology Inc. Proprietary
 Rejector Enable/ Disable
Enable or disable the rejector at the Sensor level or at the Lane level.
If one or more Sensors is checked, the reject device for all inspections performed by
those Sensors is disabled.

If all Sensors are checked, the reject device is disabled at the Lane level. An icon is
displayed in the Lane window to indicate that the rejector is disabled.
 Note: the trash can symbol is only displayed if ALL sensors within the lane are
disabled.

To enable or disable the rejector for one sensor only:

1. Go to Sensor Overview mode.
2. Right-click over the desired sensor button to see the Sensor menu.
3. Click "Reject Enabled" to toggle it to "Reject Disabled" or vice versa. If Reject
Enabled is displayed, the rejector is enabled.
If you put the system online when the Sensor rejector is disabled, you will see a message
stating "Sensor Rejector Disabled - Do you want to go online?"
To enable or disable the rejector for one or more sensors within a lane:

1. Click the tools icon to go to the Tools menu.

2. From the Tools menu, click Lane Setup, then select Rejector Enable/ Disable.
3. Check or un-check the box next to the sensor(s) to enable or disable the rejector.

102 Tools Menus System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 4. Click the OK button to apply the changes and exit the menu. The new setting is
applied. You will see the trash can icon near the statistics for that lane.

If you put the system online when the lane rejectors are disabled, you will see a message
stating "Lane Rejector Disabled - Do you want to go online?"

Forced Reject
The Forced Reject feature allows you to force any part associated with a particular
machine component to be rejected. The system will reject all parts associated with the
checked components, regardless of the condition of those parts. This provides a means of
handling an emergency situation until repairs on a blow-molder or other machine can be
made. If you know there is a serious problem with a particular component, you can use
this method to ensure that no part from the defective machine component passes the
inspection process.
 Note: the Correlation check box and machine parts are only displayed if your
machine is using correlation.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Tools Menus 103
© 2011 Pressco Technology Inc. Proprietary
 To get to this menu:

From the Lane or Sensor Overview screen, click the Tools button to see the
Tools menu, then select Lane Setup, then select Start Forced Reject.

The different parts of the menu are as follows:

Reject One Part/ Reject N Parts/ Continuous Reject
Reject one part, ‗N‘ parts, or continuously reject from a specific machine part. To
begin rejecting, click the Start Forced Reject button.
Reject One Part - rejects the next part that reaches the reject station, regardless of
its inspection or correlation status.
Reject N Parts - the numeric field next to this drop-down menu becomes active.
Enter a number of parts you want to reject, regardless of their inspection or
correlation status.
Continuous Reject - rejects all parts regardless of their inspection or correlation
status, until you click the Stop Forced Reject button.
Use Interval Between Parts
Uses the criteria set up with the Reject One Part/ Reject N Parts/ Continuous Reject
menu, adding a number of seconds that you specify between rejected parts.
Use Correlation
Uses the criteria set up with the Reject One Part/ Reject N Parts/ Continuous Reject
menu, but specifies that only parts correlated to specific machine parts get rejected.
Check the box next to any machine part, and type in a specific value (example,
Cavity 6). If you do not specify a value, then any part correlated to that machine part
will be rejected.

104 Tools Menus System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Cavity/spindle/infeed/outfeed
The names displayed in this section will correspond to the names of your machine
part components. These are only enabled if the Use Correlation box is checked.
Rejector
Specify which rejector to force rejection of part. If you only have one rejector, then
this button is not applicable.
Numeric Keypad
This is used to type values for numbers of rejected parts or correlation to machine
parts.
Start Forced Reject/ Stop Forced Reject
When you click Start Forced Reject, the criteria specified in the menu is applied
and the parts are rejected. Click the Stop Forced Reject button to stop the reject
process. Note that if you only reject one part, or specify a number of parts, the button
toggles back to Start Forced Reject automatically.
Information Box
Displays information about the rejection process.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Tools Menus 105
© 2011 Pressco Technology Inc. Proprietary
 Statistics Grid Configuration
Choose how the statistics grids are displayed.
To get to this screen:

From the Lane or Sensor Overview screen, click the Tools button to see the
Tools menu, then select Lane Setup, then select Statistics Grid Configuration.

1 Checking these boxes determines what information is shown on the

Statistics Grid screen.
2 These two slidebars allow you to enable/disable and determine the setting
for warning and error limits applied to the Statistics Grid screen.

106 Tools Menus System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Hardware Setup
Some menu items are only available to advanced level users.

1 I/O Diagnostics (on page 107) - Verify the presence of input and output
signals.
2 Extended I/O Configuration (on page 328) - Configure the optional
Extended I/O board.
3 Correlation Diagnostics (on page 108) - Verify correlation signals.
4 Offline Imaging (on page 132) - Choose how the Intellispec acquires
images when the lane is offline.
5 Part Present Delay Calibration (on page 109) - Calibrate the distance (in
encoder pulses) from the part detect sensor to the camera centerline.
6 Reject Delay Calibration (on page 111) - Calibrate the distance (in
encoder pulses) from the part detect sensor to the rejector.
7 Use part tracker simulation (on page 113) for troubleshooting or if a part
detect sensor is bad. A simulated part rate would allow inspection to
continue.
8 PDX Configuration (on page 114) - Set up the part detect generator. Only
used in some applications.
9 Missed Packets Exception (on page 115) - Set the number of missed
packets to trigger the part tracker to send a Lost Part Tracking message to
the Intellispec.

I/O Diagnostics
To get to this screen:

From the Lane or Sensor Overview screen, click the Tools button to see the
Tools menu > Hardware Setup > I/O Diagnostics.
This screen can be used to verify the presence of input and output signals. Part rate and
encoder rate are also displayed.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Tools Menus 107
© 2011 Pressco Technology Inc. Proprietary
 Green lights are input signals (signals that originate outside the Intellispec and are
communicated to the system). When an input is received the light is on.
Red lights are output signals (signals that originate inside the Intellispec and are
transmitted out of the system). When an output is generated the light is on. You can
test an output signal by clicking on the appropriate light.

The outputs correspond to the hard-wired input and output signals throughout the
Intellispec system.

108 Tools Menus System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Correlation Diagnostics
This is a troubleshooting tool to verify that correlation sensor information is being
received by the Intellispec.
To get to this screen:

From the Lane or Sensor Overview screen, click the Tools button to see the
Tools menu, then select Hardware Setup, then select Correlation Diagnostics.

For systems that have correlation sensors, this screen is used to verify that the correlation
sensor information is being received by the system. It is a troubleshooting tool.
As the production unit is operating, if the correlation sensor is transmitting pulses, it will
come up in the appropriate window. For example, if you have a cavity sensor attached to
machine part one (MP1) and are running an 8-cavity blow molder, you will see MP1
increment from 1-8 repeatedly.
Make sure that each machine part (MP) increments according to the number of
components in your system.
MP = Machine Part. MP1 through MP4 correspond to the correlation sensors that you
have configured in the Machine Part Correlation (on page 95) screen.

Part Present Delay Calibration

Part Present Delay is the distance (in encoder pulses) from the part detect sensor to the
camera centerline. Two independent signals are generated: 1) light strobe and 2) camera
snap.
 Note: if your system is using a PDX, set up PDX Configuration (on page 114)
before Part Present Delay.
The Part Present Delay ensures that your part is in the center of the image when the
camera snaps its picture. Depending on the orientation of your camera, your part could
be moving from left to right, right to left, top to bottom or bottom to top as it travels
through the camera‘s field of view. You need to be aware of the part flow direction in
order to set up the Part Present Delay Calibration.
For an illustration of Part Present Delay within the inspection process, refer to the
Sequence of Events During Inspection (on page 162).
Even if you are unsure what the Part Present Delay value should be, you can view the
strobing of the lights to gauge whether the delay has been set too long or too short. When
the Part Present Delay value has been set too short, the lights will strobe before the part
reaches the camera; likewise when the delay is set too long, the lights will strobe after the
part has passed the camera. When the part is close enough to be in the actual image that
the camera acquires, you can use the image itself to center the part. A Part Present Delay
calibration needs to be done for each camera in the system.
System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Tools Menus 109
© 2011 Pressco Technology Inc. Proprietary
 CALIBRATION
When you calibrate the Part Present Delay, it is ideal to only use one part at a time.
Otherwise, it will not be easy to determine if the part detected is actually the same part in
the image or the part rejected (for Reject Delay) since all the parts look alike. If it is not
possible to use only one part, an alternative is to use a different color part. You will most
likely use a few parts to test the calibration, or run the same part through several times.

To calibrate the Part Present Delay:

 Note: you must be logged in with proper user access to calibrate the Part Present
Delay.
1. From the Sensor Overview mode, right-click on a sensor button to view the sensor
menu (on page 129).
2. Select Part Tracking, then select Part Present Delay Calibration.
3. Click the Start Calibration button.
4. Place a part onto the conveyor or into the part stream. The part will trigger the part
detect sensor, then the system will count the number of encoder pulses and take a
picture.
5. Manually adjust the part present delay (encoder ticks) value until the image is
centered every time a part is run through the system.
6. When completed, click the Stop Calibration button. The Part Present Delay
calibration value is saved and stored in a Lane configuration file.
ADVANCED SETTINGS
 Note: Advanced settings are normally set at the Pressco factory. You should not need
to adjust them. Normal settings are listed below.
Set a Base/Neck configuration as follows:

110 Tools Menus System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
Camera Strobe Delay Trigger Delay Part Present Delay
Base 5 0 same as Neck
Neck 5 30 same as Base
Also check Advanced adjust lighting - set delay (on page 137) to make sure that the
Neck lighting delays are set correctly.

Reject Delay Calibration

Reject Delay is the distance (in encoder pulses) from the part detect sensor to the
rejector. This signal ensures that the correct part is rejected.
During Reject Delay calibration, the reject device will activate for each part that flows
through the system. Ensure that the rejector is activated properly and that each part is
rejected properly. After calibration, ensure that adjacent parts are not being rejected
(example, from too long a reject dwell time), nor being knocked off by the rejected part.
For an illustration of the Reject Time Delay within the inspection process, refer to the
Sequence of Events During Inspection (on page 162).

To calibrate the Reject Delay:

 Note: you must be logged in with proper user access to calibrate the Reject Delay.
1. From the Sensor Overview mode, right-click on a sensor button to view the sensor
menu (on page 129).
2. Select Part Tracking, then select Reject Delay Calibration.
3. Click the Start Calibration button.
4. Place a part on the running conveyor or into the part stream. After the number of
encoder pulses shown in the Reject Delay box, the rejector will be activated.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Tools Menus 111
© 2011 Pressco Technology Inc. Proprietary
 5. Make sure the correct part was rejected.
6. Continue to insert parts into the part stream.
7. Manually adjust the reject delay (encoder ticks) until the correct part is rejected
every time.
8. Adjust the Reject Dwell so that it is long enough to completely reject the part, and
short enough that only one part is rejected for each reject pulse.
9. When completed, click the Stop Calibration button. The Reject values are saved
and stored in a Lane configuration file.
Reject Dwell
The duration of the reject signal. Dwell can be set by encoder ticks or by
milliseconds. Select the correct button for your application. This signal must be long
enough to ensure the part is efficiently rejected, and short enough to ensure that only
one part is rejected for each reject pulse.
Adaptive Reject
Adaptive Reject (optional) (on page 112)

ADAPTIVE REJECT (OPTIONAL)

This feature is used to compensate for the reject device‘s turn-on time delay with varying
speeds of machine operation. An example where this is used is on a Belvac machine. The
turn-on time of the reject device might be over one-half of a can width at high machine
speeds. The Adaptive Reject will delay the activation of the reject device as a function of
encoder speed. As the belt (or production line) slows down, more delay is added.
If you do not know the fastest conveyor or production speed when you are setting Reject
Delay, you could calibrate the Reject Delay again when you run a different part at a
different production speed. Adaptive Reject allows for different speeds without having to
recalibrate between part types.
For best results when using Adaptive Reject:
Calibrate the Reject Delay when the conveyor or production line is running at a
constant speed -- not during a startup or stopping
Calibrate the Reject Delay at the fastest possible conveyor or production line speed
that you will use, if possible. Then use a value of 0 - 10 for Diff. from Calibration
(%) (see more information about Diff. from Calibration % below)
 Note: Adaptive Reject will not function properly if the reject device delay is greater
than the spacing between parts.

To set Adaptive Reject:

1. Click the check box next to Use Adaptive Reject in the Reject Delay Calibration (on
page 111) menu to enable the feature.
2. Enter the Turn On time of the reject device installed in your system.
3. Enter a value for Diff. from Calibration %, if applicable. See more information
below.
4. Set the Reject Dwell reference to Encoder Based or Time Based, and set the Reject
Dwell if it has not already been set.

112 Tools Menus System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 5. Click the OK button to save changes and exit the Reject Delay Calibration
menu.

The settings for Adaptive Reject are as follows.

Turn On Time
Latency of the rejector mechanism in milliseconds.
Diff(erence) from Calibration (%)
This number is used if the maximum speed of the conveyor or production line is
greater than the speed at which the Reject Delay was calibrated. For example, if you
calibrated the conveyor for one part where the conveyor runs at a slower speed, and
know that you will run the conveyor 20% faster for another part, then enter 20 for
Diff. from Calibration.
Note: this value only applies to potential speeds greater than calibration speeds,
not slower speeds.
The ideal setting is zero. However, a value of approximately 10 is acceptable, to
allow for speed fluctuations due to power surges.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Tools Menus 113
© 2011 Pressco Technology Inc. Proprietary
 Part Tracker Simulation
Use part tracker simulation (on page 113) for troubleshooting or if a part detect sensor is
bad. A simulated part rate would allow inspection to continue.
To get to this screen:

From the Lane or Sensor Overview screen, click the Tools button to see the
Tools menu, then select Hardware Setup, then select Part Tracker Simulation.

To enable the simulated part tracker, click the check box and then enter the desired part
rate in the window.
Part Rate - Enter a simulated part rate in parts per minute (PPM).
 Note: the system cannot run in both PDX (see "PDX Configuration" on page 114)
mode and Part Tracker Simulation (on page 113) mode at the same time. If one
mode is already running and you enable the other mode, the system displays a
warning that the latest setting will override the previous mode.

PDX Configuration
The Part Detect Generator (PDX) is used in some applications where the Intellispec
system inspects directly on a machine, rather than on a conveyor. The PDX is a circuit
built into the Part Tracker board.
 Note: the system cannot run in both PDX (see "PDX Configuration" on page 114)
mode and Part Tracker Simulation (on page 113) mode at the same time. If one
mode is already running and you enable the other mode, the system displays a
warning that the latest setting will override the previous mode.

114 Tools Menus System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 To get to this screen:

1. From the Lane Overview or Sensor Overview screen, click the Tools button
to see the Tools menu.
2. Select Hardware Setup, then select PDX configuration. The parameters are described
below:
Enable PDX
Enables the PDX circuit.
Enable PDX-Generated Pocket
 If your system is using a physical pocket disk with an index pin, leave this box
un-checked.
 If your system is not using a pocket disk, and you need the Z-index signal of the
encoder, check this box. This eliminates the need for a pocket disk. The index
signal is handled on the Part Tracker board.
Reverse Encoder
Reverses the direction of the encoder pulses. Instead of the normal A, B sequence of
pulses, the pulses switch to B, A.
Encoder Resolution (Pulses Per Rev)
Enter the resolution of the encoder installed on your machine.
Number of Parts Per Revolution
Enter the number of machine parts (example, number of Transfer Arms) to which the
encoder is attached.
To configure the PDX:
1. Click the Enable PDX check box.
2. Enter the encoder resolution used on your system (example, 8192 pulses per
revolution).
3. If your system is NOT using a pocket disk to generate the index signal, check the
Enable PDX-Generated Pocket box.

4. Click the OK button to accept changes and exit.

Missed Packets Exception

For each part and for each camera, two packets of information are communicated:
The part tracker sends the host PC a signal stating the camera has been triggered
(correlation signal)
The host PC then sends a pass/fail signal back to the tracker (results signal) when the
inspections are done
A missed packet exception occurs when the part tracker has sent out X number of
correlation signals without receiving any results signals back from the PC. The default is
set at 6.
When this number has been met a Lost Part Tracking input is received on the Sensor
Missed Statistics (on page 90) screen.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Tools Menus 115
© 2011 Pressco Technology Inc. Proprietary
 To get to this screen:

From the Lane or Sensor Overview screen, click the Tools button to see the
Tools menu, then select Hardware Setup, then select Missed Packets Exception.

Set the number of missed packets to trigger the part tracker to send a Lost Part Tracking
message to the Intellispec.

Reject Confirm Calibration

Reject Confirm can detect missed rejects. Coupled with the Missed Reject Alarm (see
"Lane alarms description" on page 80), Reject Confirm will reliably detect and notify
you of any missed reject condition. Reject Confirm is an optional feature, and an
additional sensor must be installed at your site.
Reject Confirm uses a part detect sensor positioned at a calibrated and defined distance
(Reject Confirm Delay) past the normal reject mechanism to determine whether the
defective part was actually rejected. Reject Confirm Delay must be a value of 1024 or
less.
After the rejector fires (meaning the reject delay for a part has passed), the Reject
Confirm Delay starts. Once the Reject Confirm Delay has passed, the system examines
the reject confirm sensor for a period of time equal to the Part Width. If the reject
confirm sensor ―sees‖ a part within that time, it means that the reject was missed. If the
reject confirm sensor does not see a part, it means the part was rejected successfully.
If the reject was missed, the Missed Reject Alarm will be triggered. However, the Missed
Reject Alarm (see "Lane alarms description" on page 80) must first be enabled and
configured.
Below is a timing diagram of the Reject Confirm process.

1 Reject Delay (see "Reject Delay Calibration" on page 111)

2 Reject Dwell (see "Reject Delay Calibration" on page 111)
3 Reject Confirm Delay, set by Reject Confirm Calibration
4 Part Width (see "Part Width Calibration" on page 92)
5 Part Detect (PD) - where the part is first detected by the sensor

116 Tools Menus System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 6 Image Acquired - image is taken, inspection is performed
7 Rejector Station - standard rejection point
8 Reject Confirm - second part sensor to determine whether a defective part
was rejected

To set up Reject Confirm Calibration:

1 - ENABLE THE MISSED REJECT ALARM
Go to the Lane Alarm Configuration (on page 78) to enable the alarm.
2 - CALIBRATE STANDARD REJECT DELAY
Calibrate the standard reject delay (see "Reject Delay Calibration" on page 111) using
normal procedures.
3 - SET UP REJECT CONFIRM
Mount the Reject Confirm sensor at ―X‖ distance beyond the rejector where ―X‖ is
distance in encoder ticks. For example, if there are 70 encoder pulses per inch, and the
sensor is mounted five inches beyond the rejector, the Reject Confirm Delay would be
set to 350.
 Note: The maximum setting for Reject Confirm Delay is 1024. Mount the Reject
Confirm sensor within that range of encoder ticks.
When the Reject Confirm sensor sees a part that is not supposed to be there, it triggers
the Missed Reject alarm.

To calibrate Reject Confirm:

1. From the Sensor Overview mode, right-click on a sensor button to view the sensor
menu (on page 129).
2. Select Part Tracking, then select Reject Confirm Calibration.
3. Enable Reject Confirm.
4. Click the Start Calibration button.
5. Run a part through the system.
Tip: for best results, run about 10 parts through the system.
6. When completed, click the Stop Calibration button. The system will determine the
number of encoder pulses from the part detect sensor to the reject confirm sensor.
Reject Confirm Delay is computed. Reject Confirm Delay = (number of pulses from Part
Detect to Reject Confirm Sensor) minus Reject Delay.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Tools Menus 117
© 2011 Pressco Technology Inc. Proprietary
Chapter 10
SOFTWARE UTILITIES
This section includes various software utilities that assist with Windows settings, help
and support from Pressco, and sensor configuration.

ADJUSTING DATE AND TIME

Adjust the date and time for the Intellispec system. The Windows operating system time
is also changed.
To adjust date and time:

1. Go to System Overview mode by clicking the Home button .

2. Click the Tools button to see the Tools menu.

3. Select System > Set Date and Time. The System Date and Time menu is displayed.

4. Choose your time zone from the drop-down menu.

5. Enable the check box to automatically adjust for daylight savings time if applicable.

6. Click the OK button to save changes and exit.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Software Utilities 119
© 2011 Pressco Technology Inc. Proprietary
 SETTING UP A PRINTER
Configure a USB or networked printer to print Intellispec reports. The driver for the
printer must be set up by an Administrator that has access to Windows.
To set up a printer:

1. Go to System Overview mode by clicking the Home button .

2. Click the Tools button to see the Tools menu.

3. Select System, then select Setup Printer. The printer configuration screen is
displayed.

4. Select the printer to configure from the drop-down menu. The Intellispec system
recognizes printers through the Windows drivers.
5. To test the printer, click the Print Test Page button. A basic "Intellispec Test Page"
message is printed.

6. Click the OK button to save changes and exit. The printer will be ready to use.

CREATING A SUPPORT PACKAGE

A support package is a set of files that is gathered by the Intellispec system to help
determine system problems. You will send this package to Pressco service specialists so
that they can troubleshoot your system.
What you need:
Mechanical keyboard (MKB) (on page 34) to enter problem description
USB flash drive (128MB or larger)
To set up for the support package procedure:
Connect the mechanical keyboard (MKB) to the convenience USB port (see "USB
Ports" on page 34) on the side of the user interface.
To create the support package:
1. Click a Lane n button or Sensor button to go to the Lane Overview or Sensor
Overview screen.

120 Software Utilities System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 2. Click the Help button at the top of the screen. The help menu is displayed.

3. Select the Create Support Package option. The support package wizard is displayed.
4. Follow the instructions on screen.

5. Use the forward arrows to move to the next screens.

6. When asked to describe the problem, use the mechanical keyboard to enter
information.
7. When the steps are completed, verify that the Step 4: Export screen is displayed.

8. Select the USB Flash Drive in the "Copy to:" location.

9. Click the Copy button. The support package files are copied to the USB flash drive,
then a "Copy Succeeded" message is displayed.

10. Click the OK button to continue.

11. Click the OK button at the bottom of the Support Packaging screen to exit.
12. Remove the USB flash drive.
13. Remove the mechanical keyboard (MKB).
14. Send the support package files to Pressco.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Software Utilities 121
© 2011 Pressco Technology Inc. Proprietary
 To send the files to Pressco:
1. Copy the files that were saved to the USB drive to your computer.
2. Send an e-mail to [email protected] (mailto:[email protected]) and attach
the support package files. Pressco service/ tech support will respond within one
business day, if possible.

HELP - REMOTE SUPPORT

Remote Support is used to allow remote access to the Intellispec software. This is the
method used by Pressco to provide remote system support if a Maintenance Agreement is
purchased for that Intellispec. With this software Pressco can log in and operate the
Intellispec remotely.

You will need:

A functioning Intellispec (systems without power, or systems that are not capable of
running Intellispec software, cannot be remotely accessed)
An internet connection to your Intellispec. This can be established through your
network, and is usually set up during installation. Contact your network
administrator for help.
To use Remote Support:
1. Notify a Technical Support (see "How to Contact Pressco" on page 359)
representative that you require remote support. You will need to identify yourself,
your location, and the Intellispec to which he should connect.

2. In the Intellispec software, Click the Help button . If you see the Help menu,
select Remote Support.

3. When prompted to start a remote support session, click the OK button .A

connection box is displayed.

122 Software Utilities System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Important: Do not change any of the settings in the connection box. They
have been set up during installation.

4. Click Connect Now. The connection status will change. This means that the Tech
Support representative can now connect to your Intellispec.

5. When the Tech Support representative is connected, you will be asked to give him
control of your Intellispec. Check Allow remote user MOUSE and KEYBOARD
control and click Accept. The Tech Support representative will now perform the
necessary troubleshooting of your system.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Software Utilities 123
© 2011 Pressco Technology Inc. Proprietary
 6. When the Tech Support representative is finished, he will disconnect your Intellispec
from the remote session.
If you need to disconnect your Intellispec from the remote session yourself, follow the
steps below.
To disconnect from remote support:
1. Click the X in the upper right corner of the 'iTivity Live Support Agent Connection
Status' box.
2. When the system asks "Do you really wish to exit the iTivity Live Support Agent?"
click OK. The system will be disconnected.

 Note: if you click the button, the session will be disconnected, but
this does not close the remote support program.
 If the session is disconnected and you want to allow Tech Support to be able to

access your system again, click the button.

DISCOVERY SOFTWARE - WHAT IS

DISCOVERY?
Discovery is software installed on the Intellispec hard drive that automatically looks for
and identifies certain components installed on each lane. Specifically, the software
identifies any sensors, cameras, lighting drivers, part trackers, and if used, Intellimass
drivers that are attached to the system. Each one of these devices communicates with the
Intellispec software via Cat -6 cabling and is assigned a unique MAC address.
 Note: You should rarely need to use this software. However, if a new component (for
example, camera) is installed on the system the software would be used to configure
the new camera.
Additionally, during system startup, if a previously configured component fails to
communicate with the Intellispec software, the discovery software screen will
automatically appear on the user interface, alerting you to the problem.

124 Software Utilities System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Discovery software screen

1 The tree on the left side of the screen shows the system configuration
including the lanes in the name and MAC address of each component in
that lane.
 Unassigned hardware devices are shown in red
 Missing hardware devices are shown in orange
2 This menu allows you to perform specific actions, such as add or edit
lanes or sensors, by clicking on the designated button.
3 On the top right corner is the Discovery menu toolbar (on page 125),
which allows you to perform additional actions.

Discovery Menu Toolbar

Tools Menu

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Software Utilities 125
© 2011 Pressco Technology Inc. Proprietary
 Rediscover New Hardware - when this command is initiated this software will
perform another search of all hardware communicating with the Intellispec and
displayed in the tree on the left side of the screen.
Add Simulated Devices for Testing - this is software used by Pressco engineers to
assign devices on an Intellitrainer.*
Inspection Module Preset Editor - this is software used by Pressco engineers to
assign new components as they become available.

Wizards Menu - lists the same choices as those listed in the green buttons in
the center of the screen.

Language Menu - displays language choices that can be displayed.

Help - provides software and systems for users.

*Intellitrainer = portable Intellispec training computer.

Discovery - access and use

The initial configuration of all hardware devices will be performed by the Pressco
installer, and it is not anticipated that plant personnel will normally need to use
Discovery software.
The Discovery screen is automatically displayed during system startup anytime a
hardware device that was previously configured is not communicating with the
Intellispec software.
If you need to run the Discovery screen manually, you must log in as an
Administrator, shut down the Intellispec software, and run the Discovery program
from Windows
An example of a situation where plant personnel may use the Discovery software
and actions to be taken is described next:
 During system startup camera does not communicate with the Intellispec
software
 The Discovery screen sees this as a missing piece of hardware and automatically
displays the Discovery screen. The configuration tree shows the camera in the
expected location but displayed in orange, indicating that hardware device is
missing.
 As a first step you should open the tools menu icon and select "Rediscover New
Hardware." This will trigger the software to search for the missing camera.
 If the camera re-establishes communication, as seen by the camera name
changing to black, you can close the discovery software and resume normal
operation.
 If the camera does not re-establish communication this indicates a hardware
problem and the camera will most likely need to be replaced.

126 Software Utilities System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 FAVORITES MENU
Access the Favorites menu from System Overview, Lane Overview, or Sensor Overview

menu. Click the Favorites button from the toolbar to see the menu.

This menu allows you to access the following utilities:

Take Screen Shot (on page 127)
Defect Database Tool (see "Defect Database Tool (option)" on page 339)
 Note: the Defect Database is not available from System Overview mode.

Take Screen Shot

This utility allows you to capture an Intellispec screen image. This is different from
saving individual part images through the Save Image (see "Saving Images Through the
Sensor Menu" on page 144) function. A screen shot is useful to illustrate a problem to
technical support, or to capture settings for future setup.
To capture the current full Intellispec screen:

1. Click the Favorites button to access the Favorites menu.

2. Select the Take Screen Shot option. An onscreen keyboard is displayed with a
default image name.
3. Re-name the screen shot if desired.
4. Click OK to save the image. The image is saved as a Portable Network Graphic
(.png) file to C:\Pressco\DataExport\ScreenShots.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Software Utilities 127
© 2011 Pressco Technology Inc. Proprietary
Chapter 11
LIGHTING AND IMAGING
This section includes how to adjust lighting, how to save and load images, how to use
Offline imaging, and how to use Image Analysis.

SENSOR MENU
The Sensor Menu provides access to part tracking, lighting, and image options.
Right-click the Sensor button to view the Sensor menu from the Lane Overview or
Sensor Overview mode. The items at the bottom of the menu are only available in Sensor
Overview mode.
 Note: the lane must be offline to access the items in the Sensor menu.

The items in the Sensor menu are as follows:

Reject Enabled
(Toggles to Reject Disabled) This option enables or disables the rejecter for the
Sensor only. If you disable a sensor and put the system online, you will see a
message that a rejecter is disabled.
See also Rejector Enable/ Disable (on page 101).
Camera Focus and Aperture (on page 130)
Calibrate the focus and aperture of some cameras. This menu item will be grayed out
if your system does not have cameras that can be adjusted through the software.
Camera Gain and Offset
 Note: This menu normally should not be adjusted. It is usually set by the Pressco
installer. Improper adjustment of these parameters can cause a distortion of the
image.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Lighting and Imaging 129
© 2011 Pressco Technology Inc. Proprietary
 Camera gain is the amplification of the video signal
Offset adjusts the grayscale reference values
Part Tracking
Opens Part Tracking options for:
 Part Present Delay Calibration (on page 109)
 Reject Delay Calibration (on page 111)
 Reject Confirm Calibration (on page 116)
 Part Width Calibration (on page 92)
Offline Imaging (on page 132)
Choose how the Intellispec acquires images when the lane is offline.
Image Analysis (on page 132)
This tool displays the gray shade value for any pixel or group of pixels in your
image. This is useful in programming part programs or setting up lighting. You can
measure grayscale values of pixels in horizontal or vertical lines, or over a circle.
Image Analysis also allows you to calibrate the pixel scale for the sensor.
Lighting
Opens lighting options: Basic Adjust Lighting (on page 135) and Advanced Adjust
Lighting (on page 135).
Review Camera Calibration (on page 138)
This tool shows how the current camera is calibrated - the number of image pixels to
an actual measurement on your part. Calibration is used in measurement inspections.
Save Images (see "Saving Images Through the Sensor Menu" on page 144)
Allows you to save captured images to disk.
Image Source (on page 139)
Allows you to choose which images to display, and select between live sensor
images or saved images.
Options (see "Options (sensor menu)" on page 171)
Provides different inspection tree views.
Part Program Change Log (on page 168)
Display the Part Program Change Log. This lists the inspections, and the edit history
for each. You can view all inspections from one sensor, other sensors, or even other
part programs.

Camera Focus and Aperture

This menu allows you to adjust the focus and aperture of some cameras.
 Note: only some cameras support this feature. They contain built-in motors to make
these adjustments. The Camera Focus and Aperture menu item will be grayed out in
the Sensor menu if your system does not support this feature.

130 Lighting and Imaging System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 To get to this screen:
From the Lane or Sensor Overview screen, right-click the Sensor button to see the Sensor
menu, then select Camera Focus and Aperture from the menu.

need better picture

Make adjustments as necessary.

Focus slider
Sets the focus position of the lens.
Aperture slider
Sets the aperture position of the lens.
Recalibrate/ Calibrate Focus
Determines and sets the usable range of focus positions for the lens.
Recalibrate/ Calibrate Aperture
Determines and sets the usable range of aperture positions for the lens.
Auto Focus
Automatically determines and sets the best focus position for the image.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Lighting and Imaging 131
© 2011 Pressco Technology Inc. Proprietary
 Offline Imaging
Choose how the Intellispec acquires images when the lane is offline.

TRIGGERED MODE
Single Image – using the part detect sensor, an individual picture is taken every time
the button is clicked.
Run – using input from the part detect sensor, pictures are taken continuously at the
rate set in "Image Update Interval."
IMMEDIATE MODE
Single Image – NOT using the part detect sensor, an individual picture is taken
every time the button is clicked.
Run – the camera takes a continuous picture, the light array is on, and you instantly
see whatever is under the camera.

Image Analysis
This tool displays the gray shade value for any pixel or group of pixels in your image.
This is useful in programming part programs or setting up lighting. You can measure
grayscale values of pixels in horizontal or vertical lines, or over a circle. Image Analysis
also allows you to calibrate the pixel scale for the sensor.
To get to Image Analysis:
Make sure the lane is offline. Image Analysis is not available in online mode.
Right-click an image in the Sensor Overview screen to display the zoom and image
options. Choose Image Analysis from the menu.

132 Lighting and Imaging System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 - OR -
Right-click the Sensor menu (on page 129) and choose Image Analysis from the
menu.
 Note: you must have proper user access (see "Managing Permissions" on page 52)
to use Image Analysis; otherwise, the option will be grayed out
The Image Analysis screen is displayed. The components of this screen are described
below.

1 Image analysis graph displays gray shade value for each pixel along the
line or circle. The gray shade values of the line, or unwrapped circle, are
displayed directly below the graph.
2 Circle marker - click and drag the circle to any point on the line or circle
(either in the image or in the graph)
3 Square marker - click and drag the square to any point on the line or circle
(either in the image or in the graph)
4 Measure your actual part with a ruler or calipers and enter the measured
value in this box. Place a line or circle on the image, covering the same
area you measured.
If using a line: place the end boxes of the line on the same area on the
image that you used to measure the part. This will measure length.
If using a circle: place the circle on the image over the same location you
used to measure your part. This will measure the part's diameter.
5 Choose your calibration units that you used to measure your part

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Lighting and Imaging 133
© 2011 Pressco Technology Inc. Proprietary
 6 This is a computed number that is updated after you click the Compute
Scale button. It computes the units of measure per pixel, and shows the
number of pixels measured by the line or circle.
7 Use this keypad to enter the measured value of your part.
8 Save Scale - (available after you Compute the scale) Click this button to
save the number of pixels per unit of measure to the sensor file. This
calibration unit can then be used in inspections such as Measurement or
Distance.
9 Compute Scale - Click this button after you have entered your measured
valued [item 4] and set up your line or circle. The system computes the
units of measure per pixel.
10 Click Snap to acquire one new image. This option is only available if you
accessed Image Analysis by right-clicking the Sensor button.
11 Click Run to continually snap new images. Different images are only
displayed if your production line is running. This option is only available if
you accessed Image Analysis by right-clicking the Sensor button.
12 Click the circle button to view gray shades along a circle
13 Click the line button to view gray shades along a line
14 Click and drag an end square to change the size or location of the line. If
you are using a circle for image analysis, use the middle yellow square to
re-position the circle on the image.
15 Values for each image are displayed so that you can see the difference
between images
16 The lowest gray shade value along the line or circle
17 The highest gray shade value along the line or circle
Under the graph, the information displayed is as follows:
Marker Positions
The distance in pixels that the square or circle markers are from the beginning of the
reference (red) line or circle.
Marker Value Difference
The difference in gray shade between the values of the two markers.
Marker Values
Gray shades of markers.
Computing the Pixel Scale
Image Analysis can be used to enter your actual measured values of your part and
compute the units of measure per pixel. This is called Pixel Scale.
To compute the pixel scale (refer to the illustration above):
1. Using a known good part, measure the length or diameter of an area on your part.
2. Enter that value into the Measured box [item 4].
3. Place a line or circle on the part image in Image Analysis over the same location
used to measure your part. Place the end boxes of the line, or a circle at the edges
where you want the system to measure your part.
4. Click the Compute Scale button [item 9]. The system computes the pixel scale and
displays the values [item 6].
5. To save the scale to the Sensor file, click the Save Scale button. The pixel scale is
saved with the sensor and can be used for any inspection on that sensor.

134 Lighting and Imaging System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Basic Adjust Lighting
The Basic lighting provides most of the lighting adjustments you will use.
 Note: lighting must be adjusted while the lane is offline.

To get to this screen:

1. From the Lane Overview or Sensor Overview screen, right-click over the desired
sensor button.
2. Select Lighting, then select Basic Adjust Lighting. The Basic Lighting screen is
displayed.

1 Upper right corner displays each zone. Click a zone to adjust it. You can
select a single zone or multiple zones at any one time. As lighting is
changed, the zone and the button next to it change color.
2 Separate slider bars for each color (red, green, blue, and infrared) allow
individual adjustment.
3 Incremental mode
Proportional % - Moving the slider bar adjusts all colors but maintains the
current percentage of each color.
Equal % lighting - Each color is adjusted by the same amount.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Lighting and Imaging 135
© 2011 Pressco Technology Inc. Proprietary
 Advanced Adjust Lighting
This screen provides additional lighting setup. This is mostly used by Pressco engineers,
or for making infrequently performed specialized settings.
 Note: lighting must be adjusted while the lane is offline.

To get to this screen:

1. From the Lane Overview or Sensor Overview screen, right-click over the desired
sensor button.
2. Select Lighting, then select Advanced Adjust Lighting. The Advanced Lighting
screen is displayed.

1 Opens a color palette and allows you to choose preselected colors.

2 If your inspection module has different lighting arrays, click one of the
array buttons to adjust lighting by zone.
3 By Section - Allows you to change lighting by each individual section.
By Color - Allows you to change lighting for multiple sections at once.
4 Pixel Smear - The Intellispec computes the amount of pixel smear based
on lighting, image size, and part rate. It should be kept below one.
5 On-screen keypad (OSK) - When a slide bar is selected, this keypad
allows you to type in the desired number shown in the window above the
keypad.
6 A/B buttons - Allows you to set up two different lighting settings for the
same part so you can view each and compare.

136 Lighting and Imaging System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Advanced adjust lighting - zones
When you select one of the array buttons from the Advanced Lighting screen, you can
adjust each zone independently.

7 Adjust any zone within the light array. Options:

 Adjust any zone with the slider or arrows
 Select several zones by checking their gray box to adjust those zones as
a group (intensity will be the same for the whole group)
 Right-click over any zone for options to add all zones to the group,
remove all zones from the group, or reset all zones to zero
8 Click another array button to adjust lighting zones for that array
9 Click the Back to Camera Lighting button to go back to the main
Advanced Adjust lighting screen
10 1X - 2X is an intensity multiplier. 1X is the normal setting. 2X doubles the
intensity without having to adjust the intensity through the sliders.
Maximum intensity is 100% - if a slider is already at 100%, then the
intensity will not be doubled.
11 Set Delay (see "Advanced adjust lighting - set delay" on page 137) is
only available in a BNS application.

Advanced adjust lighting - set delay

Setting the zone delay is only available in a BNS application. It provides a strobe delay
on the light control board for the Neck camera, so that the Neck lighting fires after the
Base camera (and not at the same time). Since the Base and Neck part present signal
occurs at the same time, a lighting delay is required so that the Base is lit separately from
the Neck.
 Note: this setting is normally done in the Pressco factory. You should not need to
adjust it.
System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Lighting and Imaging 137
© 2011 Pressco Technology Inc. Proprietary
 To get to this screen:
1. From a Lane Overview or Sensor Overview screen, right-click over a Sensor button
to see the lighting and imaging menu.
2. Select Advanced Adjust Lighting.
3. In the upper right corner of the lighting screen, click one of the array buttons to go to
the zone adjustment screen.
4. Near the on screen keyboard (OSK), click the Set Delays button. The Zone Delays
menu is displayed.

To adjust zone delay:

1. Enter the number of microseconds for each zone with the OSK. The normal setting
for the Neck camera is 350 microseconds on each zone.

2. Click the OK button to save changes and exit the menu.

 Note: this delay is separate from the Strobe Delay set in Part Present Delay
Calibration (on page 109).

Review Camera Calibration

This menu allows you to switch between inches and millimeters, select a custom scale, or
go back to pixels. If you switch between inches and millimeters, the pixel scale is
automatically converted. Calibration to pixel scale is performed in Image Analysis (on
page 132) or some inspections such as Measurement or Fill Height. Calibration is used to
compute measurements on a part.
The unit you select in this menu is displayed in the Inspection menus: for pixels, mm
for millimeters, " for inches, or [ ] blank for custom units.

138 Lighting and Imaging System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 To see this menu, right-click over the Sensor button in Lane Overview or Sensor
Overview modes.

Notes:
If you switch to pixels, the scale is set to 1.0. The scale will revert back to your
calibrated value if you switch from pixels to another unit.
The Reset Scale button sets the scale to 1.0 for any unit you have selected.

Image Source
This tool allows you to choose which images to display for the lane. You can load
images to simulate inspection if your production line is not running, or choose live
images from the sensor. To see this menu, right-click the Sensor button from Lane
Overview or Sensor Overview mode, then select Image Source.
 Note: you can also see most of the items from this menu by clicking the Tools button
in Lane Overview mode, selecting Lane Setup, then selecting Image Source.

From Sensor
The system displays the live images from the current sensor.
Simulated
The system displays images you have previously saved to disk. You must specify
images through one of the following options.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Lighting and Imaging 139
© 2011 Pressco Technology Inc. Proprietary
 Select Simulated Lane Images
Choose which images to display. Browse through the available directories and click

the OK button to load the images from the selected directory. On the right side
of this menu, you may see .PDL files that you have previously created. These files
are lists of images that you can load any time. See Manage Simulated Lane Images
(see "Manage Simulated Lane Images (PDL)" on page 140) to create .PDL files.

140 Lighting and Imaging System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Manage Simulated Lane Images (PDL)
Create a file [.PDL] that lists the images to load. This way, you can easily load the same
images another time. First, you must save a set of images; choose from one of the
options: Saving Images (on page 144).
To see this menu, right-click on a Sensor button in Lane or Sensor Overview mode to see
the Sensor menu (on page 129), then choose Image Source (on page 139), then choose
Manage Simulated Image Files from the menu.

To create a PDL file:

1. Click in the box for New Image Set. An on-screen keyboard is presented. Type a
name for the image file and click the OK button from the on-screen keyboard.
2. Click the Create Set button. A file is created and saved in the default directory for
the sensor (example: C:\Pressco\Lane 1\Images). The location will be displayed in
the Image Set box.
3. To add images to the set, check the Enable Modification box, then click the disk
icon next to the 'Repeat Sequentially' drop-down menu.
4. Select images for the set using the instructions under the Select Sensor Images (on
page 143) section. The drop-down menu next to the lane name (in this example:
Nickel) will show the list of images you selected.
5. Choose how to display the images using the drop-down menu on the right of the
screen.
 Repeat Sequentially - displays the images in order by file name, starting from
the first image file, repeating as long as the lane is online.
 Repeat Randomly - displays the images in a random order, repeating as long as
the lane is online.
 Run Once - not currently supported.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Lighting and Imaging 141
© 2011 Pressco Technology Inc. Proprietary
 6. Exit from the Manage Simulation Image Files menu and put the lane online. The
set of images in the PDL file is displayed.

To change an existing PDL file:

1. Click the disk icon next to the Image Set box. The Select Lane Simulation
File menu is displayed.
2. From the right side of the menu, select the PDL file that you want to change. Browse

to a different directory if necessary. Click the OK button to close the menu.

The PDL file name is displayed in the Image Set box.
3. Check the Enable Modification box. The list of images in the PDL file is displayed
in the drop down menu next to the lane name. You can add or delete images as
desired.
To delete images:
1. Click the drop-down menu next to the lane name to display the list of images in the
PDL file, and select an image name. Release the trackball buttons or click outside of
the menu to collapse the drop-down menu.
2. Right-click over the drop-down menu next to the lane name to see the Selected List
Options menu.

3. From the menu, choose to delete the currently selected image or all the images in the
PDL file. The image(s) is deleted.
To add images:
1. Click the disk icon next to the 'Repeat Sequentially' drop-down menu. The Select
Sensor Images (on page 143) menu is displayed.
2. Add or remove images by browsing through the directories, using the Add or
Remove buttons.
3. Exit from the Select Sensor Images menu. The modified list of images is displayed
in the drop-down menu next to the lane name.

142 Lighting and Imaging System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Select Sensor Images
Select individual images or a group of images to display on the lane. To see this menu,
right-click on a Sensor button to see the sensor menu, then choose Image Source, then
choose Select Sensor Images from the menu.

To select images:
1. Browse through or create the directories using the drop-down menu at the top of the
screen or the Create Directory button at bottom of the screen. The list of images in
the selected directory is displayed on the right side of the screen.
2. Select an image name from the right side of the screen. Click the All button to select
all images in the directory, or click None to de-select all the images.
 To select a subset of common images, click the Filter button. This allows you to
specify a portion of the file name.
 A wild card (asterisk [*]) is required in the filter name
 An example is using "*good*" as a filter. Since many images are saved as
either good or bad parts, this allows you to select the set of images you want.
 Another example is using "*.bmp" as a filter. The Intellispec system can
only load bitmap (.bmp) images. If your directory has different image types,
you can use the filter to select only the .bmp files.
3. Click the Add button to add the selected image(s) to the set of images to display. The
Selected Images drop-down menu contains the set of images you have chosen. Use
the Remove button to remove an image from the set.
 You can add images from more than one directory. After adding selected images
from one directory, browse to another directory and add more images. The
drop-down menu next to Selected Images shows all the image files you have
selected.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Lighting and Imaging 143
© 2011 Pressco Technology Inc. Proprietary
 4. Click the OK button to save the set of images. The next time you put the lane
online, it displays the set of images you have selected.

SAVING IMAGES
There are a number of ways to save an image within the Intellispec system:
Saving Images Through the Sensor Menu (on page 144)
Saving Images through the Retro-Spec interface (on page 145)
Saving Individual Images While Editing an Inspection (on page 150)
Saving Reject Images (on page 151)
Saving a Region of Interest (Unwrapped) Image (on page 156)

Saving Images Through the Sensor Menu

This tool allows you to quickly save a set of images (up to 100 images). You can use
these images to set up and test part programs.
To save images:
1. Right-click over the Sensor button in Lane Overview or Sensor Overview mode to
see the Sensor menu.

144 Lighting and Imaging System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 2. From the Sensor menu, select Save Images, then choose whether to save the last 100
images or the latest sensor defect images.

3. A dialog box prompts you to change directories. Click the disk button to
browse to a different folder if desired.
4. Type a prefix for the set of image files, if desired. The default "Defect" prefix is
provided for you.

5. Click the OK button to save the images.

Save Last 100 Images
Save the last 100 images captured by the current sensor.
Save Latest Sensor Defects
Save the latest defect images shown in the Reject Images thumbnails, up to 100
images.

Saving Images through the Retro-Spec interface

This topic covers how to save images through the Retro-Spec interface. You can also
Save Images (see "Saving Images Through the Sensor Menu" on page 144) from the
Sensor menu.
You may want to save images to reference later, to send to Pressco for troubleshooting
help, or to set up a part program. Saving images is done through the Retro-Spec interface
from Registrations, Orientations, or Analyses. You must first have at least a temporary
Part Program (see "How to Create, Copy, or Import a Part Program" on page 162)
loaded. You must have user access to edit part programs.
Images are saved as grayscale bitmap images, at 302 KB in size. No graphics are saved
with the images.
I don't see any graphics, although there's now an option. I tried saving with graphics, and both. Still only get one bitmap image - no graphics files. - this might not be implemented yet - the graphics saving [BW 082111]

To save one or more images:

1. Go to Sensor Overview mode [from Home, click Lane button, then Sensor button].
2. Put the lane online for a while to acquire several part images.
3. Take the lane offline to stop acquiring images (if desired).
4. Double-click the name of any Registration, Orientation, or Analysis in the inspection
tree to view the Retro-Spec interface. Note: you cannot save images through a
Region of Interest (ROI).
5. Right-click the Retro-Spec graph to see the Retro-Spec options (on page 181) menu.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Lighting and Imaging 145
© 2011 Pressco Technology Inc. Proprietary
 6. Select an option for Data Set A and/or Data Set B (from Select Data Set A and
Select Data Set B).
7. In the Retro-Spec graph, click the bar corresponding to the image you want to save.

Note: You can save a whole data set from the Save Image Files menu.

8. Click the disk icon on the Retro-Spec graph. The Save Image Files menu is
displayed.

146 Lighting and Imaging System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 9. Choose which images to save under the "Save What?" column. Save only the
selected part image, or all the images from Data Set A or Data Set B.
10. Choose the type of image to save under the "Save Type" column. Save the image
only, the image with the graphics overlaid, or two separate images (both).
11. To name the image files, enter a prefix in the "File names start with" box. The
default prefix is "I" for "image." This step is important if you already have saved
images and you do not wish to overwrite them.
12. Use the disk icon under "Where to Save?" to browse to the location where you
want to save images. Use the Select Location menu to save images to the Intellispec
hard drive or to a USB device. Create a new directory, if desired, to your images.

13. Click the OK button twice to save the image(s).

Note: all images in a data set will be named with unique file names. However, if
you save another data set to the same folder at a later time using the same prefix,
the original images will be overwritten. See Recommendations for Image File
Management (on page 148).
14. To save subsequent single images to the same location, click the bar for another part
and then click the disk icon on the graph. The part image will be saved.
You can load (see "Loading Images" on page 156) saved images at a later time for
reference, setting up a part program, or testing.

 Note: Part images can be dragged to the disk icon and saved if the Lock/Move

Parts button is unlocked:

 See more information about the Lock/Move Parts button in the Retro-Spec
Population View Graph (on page 179).

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Lighting and Imaging 147
© 2011 Pressco Technology Inc. Proprietary
 Recommendations for Image File Management
When you save the images for data sets to a folder, each image is given a unique name.
However, if you save another data set to the same folder, those original images are
overwritten. Therefore we recommend that you create new folders when you save data
sets. Our recommendations are:
Make new folders and give them meaningful names
Add the word Defects to the folder name to indicate that you are storing defects for
that inspection
When you are saving images (see "Saving Images through the Retro-Spec interface" on
page 145), you can create new folders (directories).
To create a new folder while saving images:
1. Click the disk icon on the Retro-Spec graph. The Save Image Files menu is
displayed.

148 Lighting and Imaging System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 2. Click the disk icon to browse folders. The Select Location menu is displayed.

3. Click the button at the top of the menu to browse to the location that makes sense to
the sensor (example, "C:\Pressco\Lane 1\Images\Sensor 1\"). Note that you can also
save images to a USB device.
4. Click the Create Directory button to create a new folder. Rename the folder
something meaningful, such as the area of inspection (example, Countersink). If you
are saving images of defects, use Defects in the folder name.

5. Click the OK button to complete browsing and return to the Save Image Files
menu.

6. Click the OK button to save the images. Depending where the images are
being stored, it may take up to a minute to complete, especially if a USB device is
used.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Lighting and Imaging 149
© 2011 Pressco Technology Inc. Proprietary
 Saving Individual Images While Editing an Inspection
You can save one image while editing an inspection. To save the image, right-click over
the image to see the Image Options menu. Select Save Image from the menu, then choose
the desired option.

The options are shown below.

Image Only
Saves a bitmap (.bmp) image with no graphics.

 Note: only bitmap images can be loaded back into the Intellispec

Image with Graphics

Saves the current image with inspection graphics on the image. It is saved as a
Portable Network Graphic (.png) file.
Both
Saves both files - (.bmp) with no graphics, and (.png) with graphics.

150 Lighting and Imaging System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 When you save an image, a dialog box, as shown below, provides options for saving the
image. The image is saved to the default location shown in the box, unless you click the
disk icon and specify a different location. A default file name including Lane name, date,
and time is provided for you. You can rename the image by clicking on the keyboard
icon and typing a new name using the on screen keyboard.

Saving Reject Images

You can save images from parts that were considered defective, either from Lane
Overview or Sensor Overview mode. This can be done when the Reject Images button
on the right side of the screen is selected. Up to 100 images can be saved at a time. These
images can be be loaded at a later time as simulated images to assist in programming
inspections or training.

To save reject images:

1. Right-click over any image displayed in the reject image area on the screen (Images
in Sensor Overview mode shown below). The Defect Image Options menu is
displayed.

2. Select Save Defect Images from the menu. The Save Image menu allows you to
change the directory or name of the images to be saved. A default name and
directory are provided for you.
3. Change the directory or file name if desired and click the OK button to exit. The
images are saved as bitmap (.bmp) images. Each image is given a unique name.

Saving Reject Images by Inspection

You can save images that failed a specific inspection in Sensor Overview mode [from
System Overview mode, select a lane, then click a Sensor button [item 1] to go to Sensor
Overview mode]. There are two ways to save inspection-specific images. Refer to the
illustration below.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Lighting and Imaging 151
© 2011 Pressco Technology Inc. Proprietary
  Note: If you select an inspection that did not fail any parts, all reject images from
that sensor, up to 100 images, are saved.

If the Reject Images button [item 4] is selected on the right side of the
screen:
1. Click the name of an inspection [item 3] in the inspection tree. The images
associated with that inspection are displayed in the thumbnail image area.
2. Right-click over the set of images to see the Defect Image Options menu [item 2].
3. Select Save Defect Images from the menu. The Save Image menu allows you to
change the directory or name of the images to be saved. A default name and
directory are provided for you.
4. Change the directory or file name if desired and click the OK button to exit. The
images are saved as bitmap (.bmp) images. Each image is given a unique name.

1 Sensor button
2 Right-click over image thumbnails to see Defect Image Options menu
3 Select one inspection to view defect images associated with that
inspection
4 Select the Reject Images button to view thumbnails of images from
defective parts

If the Statistics button [item 4a] is selected on the right side of the screen
(refer to the illustration below):
1. Click the name of an inspection [item 3a] in the inspection table. The images
associated with that inspection are displayed in the thumbnail image area.
152 Lighting and Imaging System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 2. Right-click over the set of images to see the Defect Image Options menu [item 2].
3. Select Save Defect Images from the menu. The Save Image menu allows you to
change the directory or name of the images to be saved. A default name and
directory are provided for you.
4. Change the directory or file name if desired and click the OK button to exit. The
images are saved as bitmap (.bmp) images. Each image is given a unique name.

1 Sensor button
2 Right-click over image thumbnails to see Defect Image Options menu
3a Select one inspection to view defect images associated with that
inspection
4a Select the Statistics button to view detailed inspection statistics

Saving Reject Images by Machine Part

You can save images that failed inspection and are associated with specific machine
parts.
To save images associated with a machine part (refer to the illustration
below):
1. Go to Sensor Overview mode: from System Overview mode, select a lane, then click
a Sensor button [item 1] to go to Sensor Overview mode.
2. Click the Machine Parts button [item 4b] on the right side of the screen. The images
associated with machine parts are displayed in the thumbnail area.
3. Select a different machine part from the drop-down menu [item 3b], if desired.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Lighting and Imaging 153
© 2011 Pressco Technology Inc. Proprietary
 4. Select a specific machine part from the graph [item 5]. The name of the machine part
is displayed in the button above the V-axis selection.
5. Right-click over the set of images to see the Defect Image Options menu [item 2].
6. Select Save Defect Images from the menu. The Save Image menu allows you to
change the directory or name of the images to be saved. A default name and
directory are provided for you.
7. Change the directory or file name if desired and click the OK button to exit. The
images associated with that machine part are saved as bitmap (.bmp) images. Each
image is given a unique name.

1 Sensor button
2 Right-click over image thumbnails to see Defect Image Options menu
3b Select a machine part type
4b Select the Machine Parts button to view thumbnails of defective parts
associated with specific machine parts
5 Select a specific machine part from the graph

154 Lighting and Imaging System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Saving Individual Reject Images
You can select any thumbnail image in Sensor Overview mode and save it.
To save an image (refer to the illustration below):
1. Go to Sensor Overview mode: from System Overview mode, select a lane, then click
a Sensor button [item 1] to go to Sensor Overview mode.
2. Click any thumbnail image [item 3c] (available when Reject Images or Statistics
button is selected). The Reject Images button becomes selected after you select the
thumbnail image.
3. Right-click over the large image at the bottom of the screen to see the Image Options
menu [item 2c].
4. Select Save Image from the menu. Choose to save the Image Only, Image with
Graphics, or Both. For information about these options, refer to Saving Individual
Images While Editing an Inspection (on page 150). The image is saved.

1 Sensor button
2c Right-click over the image to see Image Options menu
3c Select a thumbnail image
4c When you select a thumbnail image, the Reject Images button becomes
selected for you

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Lighting and Imaging 155
© 2011 Pressco Technology Inc. Proprietary
 Saving a Region of Interest (Unwrapped) Image
You can save the unwrapped region display while you are editing an inspection. The
image will be saved as a Portable Network Graphic (.png) file. An example unwrapped
image is shown below. The image will be the same dimensions as the defined region of
interest. Note that the Intellispec stretches some images to fit the region of interest
window.

 Note: whether regions, edges, or other graphics are saved depends on the settings
when you save the image. If diagnostics are on, or if Show Graphics is enabled,
those items are saved with the image.

To save the unwrapped image while editing an inspection:

1. Right-click in the unwrapped image area to view the ROI Options menu.

2. Choose Save Image from the menu. The Save Image menu allows you to change the
directory or name of the image to be saved.
3. Change the directory or file name as desired and click the OK button to exit. The
image is saved as a .png file.

LOADING IMAGES
This topic covers how to load images through the Retro-Spec interface. You can also
choose an Image Source (on page 139) through the Sensor menu.
You can load images previously saved (see "Saving Images through the Retro-Spec
interface" on page 145) on the Intellispec to use as reference, test part sets, or to set up a
part program without the production line running. You must have user access to edit part
programs.
To load images:
1. Go to Sensor Overview mode [from Home, click Lane button, then Sensor button].
2. Double-click the name of any Registration, Orientation, or Analysis in the inspection
tree to view the Retro-Spec interface graph. A partial graph is shown below.

156 Lighting and Imaging System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 3. Click one of the left or right arrow buttons to view the Select Data Sets
menu.

4. Click the Image Files button for either Set A or Set B.

5. Click the disk icon to browse to the folder where the images were saved. The
Select Location menu is displayed.

6. Browse to and select the folder that contains the images you want to load.
 To preview the images in the folder, browse through the file names in the
window on the right of the Select Location menu.

7. Click the OK button twice. The Intellispec loads all the bitmap images that
were previously saved in the selected folder.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Lighting and Imaging 157
© 2011 Pressco Technology Inc. Proprietary
 IMAGE OPTIONS
While viewing an inspection screen, right-click in the part image to see the Image
Options menu. A small check indicates that the option is currently active. Click an option
to make it active or toggle it to inactive. The default Image Options menu is shown
below.
 Note: some menu items are not shown when you are viewing a registration or
orientation.

There are options for certain regions. Options are grayed out if they do not apply to the
current inspection.
Zoom - 6X, 4X, 2X
Magnify the image by the specified amount.
Normal Resolution
Returns the image to normal size.
Save Image
Save an individual image. Refer to Saving Individual Images While Editing an
Inspection (on page 150).
Image Analysis
Not available from this menu as of this printing.
Image Analysis (on page 132)
Show Graphics
Displays the region and graphics for the current inspection.
Show Regions
Displays the region(s) from other inspections in the same part program.
Hide Region Shading
Removes the shaded graphics from the screen so that you can see more of the part
image.
Show Defects
Not available from this menu as of this printing.

158 Lighting and Imaging System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Enable Region Editor
Allows you to change the shape and placement of the region directly on the image.
Display Large Region Editor
Displays a large part image on which you can change the shape and placement of the
region. Check Enable Region Editor to make the changes to the region. Un-check
this option to return the image to normal size.
Enable Moving Center
[Available when you are editing a region] Allows you to change the center of the
region when you are using Region Editor directly on the image.
Enable Region Resizing
Allows you to resize the region directly on the image.
Enable Set Region Direction
[Available in certain inspections, such as Measure ROI] When this feature is
enabled, click on the region in the image. The region box will be displayed in yellow
with diamonds around the box. Click on one of the diamonds to make the inspection
search in the direction of the selected diamond. The selected diamond is filled in
solid yellow.
Center Ring
[Available when you are using Region Editor directly on the image, and Enable
Moving Center is checked.] Click Center Ring to re-center the region on the image
using the current parameters. This is a command; there will be no check mark next to
this option.
Edit Mode
A Polygon inspection has the option to ―Complete Build Mode‖ to add points to the
polygon. Edit Mode becomes available after a Build Mode is complete. Options
below are only active if a check mark appears next to the option in the menu.
Delete - Click all polygon points that you want to delete. To stop deleting points,
right-click to see Image Options menu. Select Edit Mode > and un-check Delete.
Add - Click anywhere between two points to add another point. To stop adding
points, right-click to see Image Options menu. Select Edit Mode > and un-check
Add.
Move - moves one point in the polygon. Move the cursor over the point you want to
move, then click and drag the point.
Enable Moving Region - [only available when Move is enabled] Move the entire
region at once. To move the polygon, click anywhere on the image except on one of
the yellow polygon points. Click and drag the polygon to move it.
Enable Rotate Around Center - [only available when Move is enabled] Rotate the
entire polygon with respect to the center. To rotate the polygon, click anywhere on
the image except on one of the yellow polygon points. Click and drag the polygon to
rotate it.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Lighting and Imaging 159
© 2011 Pressco Technology Inc. Proprietary
Chapter 12
INSPECTION OVERVIEW
This section includes basic information about part programs, part tracking, and
Retro-Spec graphs. For detailed information about adding or adjusting inspections, see
the section about Inspections (on page 185).

INSPECTION TERMINOLOGY
The following terms are used throughout this manual and the software. A basic
understanding of this terminology will help you understand how the system operates.

Term Description
Enhancements (on page Enhancements are used to alter images for the purpose of better defect
198) detection, or for making certain features stand out.
Analyses (on page 231) An analysis usually analyzes the pixel shade information within a region and
compares it to programmed reference values. The inspection passes or fails
based on these comparisons. You may have many analyses for each
inspection region.
Inspection Module The housing, camera, cables, and associated electronics that are installed on
or over the production line to acquire an image of your products. Sometimes
referred to as a tunnel. The inspection module can consist of a different sensor
than a camera to make measurements of your product.
Lane A lane usually refers to one production line, and can contain multiple sensors.
Orientations (on page An orientation compensates for part rotation by finding a grayscale pattern. An
228) analysis which must rotate with the part must follow an orientation.
Part Program The list of regions, analyses, registrations, etc. programmed specifically for
your part to detect defects or make measurements.
Part Tracking (on page Part Tracking refers to the monitoring of parts from the part detect sensor to
162) reject station. This ensures that the correct parts are rejected at the correct
time, and that good parts remain in the part stream.
Region The Region indicates where on the part the analyses will take place. You may
have as many analyses, enhancements, registrations, or orientations as you
like in one region.
Registrations (on page A registration compensates for part movement by calculating the reference
211) point on the part. All analyses follow a registration.
Reject A part that failed one or more inspections from any sensor. The part can be
physically rejected, or simply counted in the statistics.
Retro-Spec The graphical interface used in inspections that allows you to make quick
changes to a part program. It also allows you to experiment with different
parameter settings to see how changes would have affected the most recent
inspection population, without unnecessarily rejecting parts.
Sensor A camera, Intellimass, or other sensor that acquires images, measurements, or
other data from your product.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspection Overview 161
© 2011 Pressco Technology Inc. Proprietary
 SEQUENCE OF EVENTS DURING
INSPECTION

PART TRACKING
Part Tracking refers to the monitoring of parts from the part detect sensor to reject
station. This ensures that the correct parts are rejected at the correct time, and that good
parts remain in the part stream.
Part Tracking includes:
Part Present Delay Calibration (on page 109)
Reject Delay Calibration (on page 111)
Reject Confirm Calibration (on page 116)
Part Width Calibration (on page 92)

HOW TO CREATE, COPY, OR IMPORT A

PART PROGRAM
A new Part Program can be created from scratch, imported or exported to/from disk, or
copied from an existing part program. A Part Program is created in the Lane Overview or
Sensor Overview screen.

162 Inspection Overview System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 You will need:
User access to create part programs.
The mechanical keyboard (MKB) (on page 34) to enter program names.
To create a Part Program:
1. Go to a Lane Overview or Sensor Overview screen [from Home: Lane button >
Sensor button].
2. Right-click over the part program drop-down menu. The Manage Part Programs
menu is displayed. Choose from the available options described below.

Right-click

To create a new program:

1. Click the New button. The Create Part Program Wizard is opened.
2. Follow the steps on the screen.

3. After step two of the create part wizard, click the OK button to save the new
part program. The blank part program is created.
4. Add Regions, Registrations, Orientations, or Analyses as appropriate for your part.
To copy a program:
First click on a name from the available list of part programs, then click the Copy button.
A copy of that part program is saved under a default name such as "(1) Penny." You can
use this copy of the part program to modify it to inspect a slightly different part, or
modify the copied part program without changing the original program.
Use the Rename button to rename the program to something more meaningful to you.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspection Overview 163
© 2011 Pressco Technology Inc. Proprietary
 To import an existing program:
1. Click the Import/Export button. An "Import or Export Part Programs" menu allows
you to choose a part program from disk.

2. To browse to another location on the computer, click the disk icon .

3. Locate the desired folder and click OK in the menu. The Intellispec will only choose
part program names with a ".PPP" extension. You will not be able to see the names
nor extensions when choosing through this menu.
 In this example, we clicked the Part Programs folder, then clicked OK to view
the available part programs.

4. To import the part program, highlight the name in the right side of the menu under
"Disk."
5. Click the left arrow. The part program is imported into the "Current Part Programs"
list.
6. Click the OK button to exit the menu.
To load the new program:
1. Highlight the program name in the Manage Part Programs menu, then click the Load
button. The program name will appear in the Part Program drop-down menu on the
Lane Overview or Sensor Overview screen.

2. Click the OK button to exit the Manage Part Programs menu.

See also Export a part program (on page 99)

164 Inspection Overview System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 PART CHANGEOVER
When you change your production line from one part type to another, you can quickly
change the part program.
 Note: Some menu items are only available to advanced level users.

What you need:

User permission to "Change Part Programs"
To change parts:
1. Log in (see "Logging in and logging out" on page 45).
2. Click the part drop-down menu.

3. Click the name of the new part to inspect. The new part program is loaded on the
Intellispec.
4. Put the system online to begin inspecting new parts.
Contained in each Part Program is lane specific information. Everything you set up have
previously set up is stored: camera information, lighting information, calibration
information, regions, enhancements, and analyses.

Lane Specific Information Definition

Cameras (or other sensor) All information for each camera or other sensor is contained in the Part
Program.
Lighting Each camera has different lighting settings for each part. When you load
your Part Program after a Part Changeover, the lighting will be specific for
that part and save any changes you make.
Calibration Calibration setup for Part Present Delay and Reject Delay is saved for
each part you will run. Part Present and Reject Delay will only need to be
set up once.
Regions, Registrations, All Inspections will be contained in your Part Program. Also, parameter
Orientations, Enhancements, changes are saved for each Part Program.
Analyses, Measurements

INSPECTION MENU
The Inspection menu is used to create and edit part programs. Right-click over any
analysis, region, or orientation name to see the Inspection menu. A menu similar to the
one shown below is displayed.
 Note: For simplicity, we use the term 'inspection' to include analyses, regions,
enhancements, registrations, etc.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspection Overview 165
© 2011 Pressco Technology Inc. Proprietary
  Note: some items may be grayed out if you do not have user access to those items, or
if they do not apply to the current menu.

The items in the Inspection menu are as follows:

Info
Display general information about the inspection.

1 Name - the name you have given the inspection

2 General type - Analysis, Region, Orientation, etc.
3 Specific type - sub-category (example, Ring, Polygon, or Measurement
Region)

Edit Analysis/ Region/ Orientation

Open the Inspection Editor - performs the same action as double clicking.
Enable/ Disable Inspection
Temporarily turn off the inspection. If an inspection is disabled, all of its dependent
inspections will be disabled as well. The inspection name is grayed out when it is
disabled.
Enable/ Disable Inspection Reject
Temporarily pass all parts regardless of whether they pass or fail the current
inspection (if Reject is Disabled). The inspection is grayed out when the inspection
reject is disabled.

166 Inspection Overview System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Enable/ Disable Empty Pocket (on page 185) Check
When the Empty Pocket Check is enabled, the inspection is highlighted in blue in the
menu as shown below.

Rename
Rename the inspection to something that makes sense to you. This name will appear
in the inspection tree, graphs, and anywhere else the inspection name occurs.
Insert
Choose from the available list to add one item above the currently selected item.
Add
Add an item from the available list. The list varies, depending on the current item.
Replace
Replace the current item with a similar item. Regions can be replaced with other
regions, registrations replaced with other registrations, etc.
Delete Analysis/ Region/ Orientation
Delete the current item from the inspection tree list. If the item has other items below
it (at a lower hierarchy), those items are deleted as well.
Delete All Inspections
[only shown when you right-click on "Inspections" at the top of the inspection tree]
Delete all inspections from the current part program.
Part Program Change Log (on page 168)
Display the Part Program Change Log. This lists the inspections, and the edit history
for each. You can view all inspections from one sensor, other sensors, or even other
part programs.
Copy
Copy the current item and descendants (if applicable). The items are copied to the
clipboard. Use Paste to place them in the inspection list. You may copy a part
program to the same sensor, a different sensor, or different lane.
To copy the part program to another Intellispec system, use the Export function. See
Export a part program (on page 99).
Paste
Paste the contents of the clipboard into the inspection list. The contents are pasted
below the currently selected item.
Collapse All
[only shown when you right-click on "Inspections" at the top of the inspection tree]
Collapse the inspection tree to the top level inspection. This does not affect
inspection.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspection Overview 167
© 2011 Pressco Technology Inc. Proprietary
 Part Program Change Log
The part program change log lists the inspections, and the edit history for each. You can
view all inspections from one sensor, other sensors, or even other part programs. This is
helpful especially if you want to see the previous settings for an inspection.

To view the part change log:

1. Click a sensor button to go to Sensor Overview mode.

2. Right-click over a sensor button or inspection name and select Part Program
Change Log from the Inspection menu. If you right-clicked over an inspection
name, and the current inspection has never been changed since it was set up, no data
is displayed.
3. Click any of the available check boxes to view other inspections, inspections from
other part programs, or inspections from other sensors. Some boxes are dependent on
others; for example, you must click a dark gray check box before a light gray check
box becomes active.
To view a full column width, click and drag the column title to re-size that column.

168 Inspection Overview System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Click the Details button to see more information about the highlighted item. A pop-up
window displays more information, including the number of times the inspection was
modified.

Click the Filter button to choose the items to display in the log. As soon as you select
any option, the Change Log is updated. Some options are dependent on others; for
example, if you want to see the Historic Names for the Sensor, you must choose Historic
Names for Inspection first.

To see inspection differences:

1. Click the Difference button to see a list of differences in inspections. A Mark Start/
Mark Stop menu is displayed, and the inspections in the list are highlighted in
magenta (depending where your cursor is).

2. Click the Mark Start button.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspection Overview 169
© 2011 Pressco Technology Inc. Proprietary
 3. Click on the first item in the list where you want to begin viewing inspection
differences. (this is similar to holding the Shift key and selecting multiple items in a
list)
4. Click the Mark Stop button.
5. Click on the last item in the list where you want to view inspection differences. Your
selected items are highlighted in magenta.

6. Click the OK button in the Mark Start/ Mark Stop menu. A Differences table is
displayed. This allows you to view a shorter list of items, only those of which have
been changed. Only edited (not created) inspections are included.

ROLLBACK
This feature allows you to restore the part program to a previous state, allowing you to
undo several changes at once.
To use the Rollback feature:
1. Check the box next to the Rollback button at the top of the Part Change Log Viewer
screen.
2. Scroll down towards the bottom of the inspection list. The latest changes are at the
bottom of the list.
3. Choose a line where you want to delete the latest changes, including the selected
line.
4. Click the Rollback button near the top of the screen. A Rollback Preview is
displayed so that you can see what will be deleted.

5. If desired, click the Details button to see the inspection change details of each line.

6. If you are ready to delete the displayed lines, click the OK button . The lines are
deleted, and the part program is changed back to a previous state.

170 Inspection Overview System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Inspection type icons
In the Inspection tree, you may see icons or symbols that indicate the General Type of
inspection for each item. These allow you to quickly identify these inspections, without
the need to view more information through the menus.
 Note: these are options. To enable icons or symbols, right-click on a Sensor button in
the Sensor Overview mode and select Options >> check Show Icons or Show
Symbols.

Icon Symbol General Inspection Type

Region - location of inspection

Registration - to find part center or point of reference

Analysis - inspection

Orientation - to place an inspection on the same location on each part,

regardless of part rotation

Enhancement - to add image processing to make defects or part

features stand out better

Options (sensor menu)

The Sensor Options menu allows you to display the inspection tree the best way for you.
Some options hide objects from the inspection tree which makes it easier for
adjustments. Other options display icons or symbols to help you quickly identify
inspection types.
 Note: these settings apply to the current sensor view only.

To enable an option:
1. From the Sensor Overview mode, right-click a Sensor button.
2. Select Options >> then select one of the options described below. An option is
enabled when a check mark is displayed next to the option.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspection Overview 171
© 2011 Pressco Technology Inc. Proprietary
 Show Icons
Displays icons that reflect the different inspection types (see "Inspection type icons"
on page 170).

Show Symbols
Displays symbols that reflect the different inspection types (see "Inspection type
icons" on page 170).

Show Standard Names

Displays the default Intellispec inspection names. You may have other inspection
names that make sense to the inspection of your part. Showing Standard Names is
useful to Pressco engineers or to someone troubleshooting your machine, so that they
quickly know the exact inspection type.

INSPECTION TREE RELATIONSHIPS

The inspection tree shows the relationship of each inspection. Indented objects are
dependent on the object above it. Indented objects are created when you "Add" an item
from the Inspection menu.

Some items in the menu may be turned off. The ability to access some items depends on
your user access.

172 Inspection Overview System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 If an item is displayed in red, the Inspection Reject has been disabled.
If an item is grayed out, the inspection has been disabled. All descendants of that
item are also disabled.
The Design Mode icon provides additional part program restrictions. Click the icon to
see the options.

If you select Edit Only, then users are allowed to edit, but not add, the inspections.
This also restricts access to regions.
If you select Design and Edit, then users are allowed to edit and add inspections, as
well as add and edit regions.
 Note: some users (for example, Operators) cannot edit or add inspections regardless
of this setting. To add and edit inspections in Design and Edit mode, users must also
have proper permissions. See Managing Permissions (on page 52).
See also how to create a part program (see "How to Create, Copy, or Import a Part
Program" on page 162)

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspection Overview 173
© 2011 Pressco Technology Inc. Proprietary
 ADDING REGIONS AND INSPECTIONS
To add an Analysis, Enhancement, etc., you must first add a Region. The Region
indicates where on the part Analyses or Enhancements are applied. Right-click over the
inspection tree, select Add, then choose an item to add. You may add as many
inspections underneath the region as you wish.

REGION EDITOR
This view is available when you are editing a region. If you have proper user access, you
can edit a region by double-clicking the region name, or right-clicking the region name,
then selecting Edit Region from the pop-up menu.

1 Unwrapped Region of Displays a linear view of the region from the edited inspection.
Interest
2 Part Image Displays a view of the part with the editable region on the part.
3 Editable Region This is the region on the image that can be edited. When the lines are
yellow, they can be edited. To enable region editing, right-click on the
region and check "Enable Region Editor." The region can be sized and
moved using the track ball and buttons or by using the optional touch
screen.
4 Previous and Next Allows you to select the next or previous image.
Image
5 Refresh Data Set Takes up to 100 images with the current sensor and replaces Data Set A.
6 Snap Image Takes one image with the sensor and adds it to the end of Data Set A.
7 Editable Parameters Adjust different parameters associated with the current region.
174 Inspection Overview System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
8 Parameter Description Gives a brief description of the selected parameter.
Window
9 Undo, Redo, Accept, Allows you to undo, redo, accept or cancel any changes made throughout
and Cancel the process of editing.

INSPECTION EDITOR
The following illustration shows the various parts of the screen displayed when you edit
an inspection.
 Note: the Retro-Spec graph (see "Retro-Spec Population View Graph" on page
179) at the top of the screen is described separately.

1 Unwrapped Region of Displays a linear view of the region from the edited inspection. This region
Interest is marked with two directions: "S" for "Slow direction" and "F" for "Fast
direction." These designations are used in some inspection descriptions to
help you understand how they work.
2 Part Image Displays a view of the part with the editable region on the part.
3 Previous and Next Allows you to select the next or previous image.
Images
4 Refresh Data Set Takes up to 100 images with the current sensor and replaces Data Set A.
5 Snap Image Takes one image with the sensor and adds it to the end of Data Set A.
6 Inspection Parameters Displays the available parameters for the selected inspection. Note: there
can be multiple tabs; the parameters will vary per inspection.
System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspection Overview 175
© 2011 Pressco Technology Inc. Proprietary
7 Parameter Description Gives a brief description of the selected parameter.
Window
8 Results Box Shows the results from the current inspection with the option to see results
from other inspections and timing information.
Right-click over the various areas of the menu to see image options, editor options, result
options, and region of interest options.

Editing Parameters
You can change values, display settings, and options that will alter the outcome of an
inspection. For the purpose of this discussion, we refer to inspections, but the
information applies to regions, registrations, orientations, enhancements, measurements,
and correlations as well.
 Note: you must have appropriate user permissions to edit parameters

To edit parameters:
Open the inspection from the Sensor Overview screen:
 Double-click the inspection name in the inspection tree. Or:
 Right-click the inspection and select Edit Inspection from the pop-up menu.

1 Select a tab to adjust parameters. The orange tab contains the parameters
that can be adjusted with the bars on the Retro-Spec graph. The tabs
displayed depend on the inspection itself, and its relationship within the
inspection tree.
2 Numeric value can be adjusted by Large Slider or Numeric Text Entry
[described below]
3 Check box to enable or disable the feature
4 Backwards R indicates the current parameter that can be adjusted in the
Retro-Spec graph (example: the red and yellow limits bars). Note that you
can also adjust parameter limits by right-clicking over the Retro-Spec
graph.
5 Column division for parameter settings (this line is not actually displayed in
the Intellispec). You can see Large Slider AND numeric entry pad if you
click in the left column, or just the numeric entry pad if you click in the right
column (this only applies if Numeric Input setting = both).
There are several ways to change parameters:

176 Inspection Overview System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Numeric values
Check boxes
Drop-down menus
Buttons
Adjusting the bars on the Retro-Spec graph
 Note: Drop-down menus and buttons are discussed separately in the inspections
where they are used
EDITING NUMERIC VALUES
There are a few ways in which to change values and settings which include large slider,
numeric text entry, or drop down. The method available depends on Editor Options as
described below.
Large Slider
Allows you to make changes using a sliding bar. It displays the value in the menu as
you slide the bar. Changes made on the Large Slider are reflected in the Numeric
Text Entry as well if both are open. Changes are also applied to the red and yellow
sensitivity bars in the Retro-Spec graph.
If the parameter has an upper and lower limit, portions of the bar are displayed in
different colors, as shown below:

 Red = failure limit. Any part whose parameter value falls in the red zone fails
inspection.
 Yellow = warning limit. Any part whose parameter value falls in the yellow zone
is tagged as a warning level part.
 Green = passing. Any part whose parameter value falls in the green zone passes
(at least this parameter).
Numeric Text Entry
Allows you to type in a specific number. You can use the +1 and -1 feature to make
minor adjustments. Changes made on the Numeric Text Entry are reflected in the
Large Slider as well if both are open.
For more information about the numeric keyboard, see On Screen Keyboard (OSK)
(on page 32)
EDITOR OPTIONS
The information displayed when you are editing parameters depends on the Editor
Options settings. Right-click over the parameters menu to see the Editor Options.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspection Overview 177
© 2011 Pressco Technology Inc. Proprietary
 Editor Access
Choose how parameter names are displayed.
 Normal = the names of the parameters as you normally see them; if you have
re-named any parameters to make more sense to you, this is how they are
displayed.
 Initial Setup = the names of the parameters when the Intellispec system was
installed, after applying the appropriate application template.
 Show Untemplated = default Intellispec names. Some parameter names were
changed in templates to make more sense for a particular application.
Enable Region Editor
Available when the inspection has an associated region that can be modified.
Numeric Input
 Slider = Large Slider as described above
 Text Entry = Numeric Text Entry as described above
 Both = both Large Slider and Numeric Text entry. After you make changes to

either input, you must click the OK button on both to close them.
 Text entry on click on value side = if you click an item the right column of the
menu, you will see only the Numeric Text Entry box, even if you have Both
checked

Result Options
There is additional display information for the Results Box. Right-click to see the menu.
To stop displaying the other inspections, right-click the menu again, then un-check the
option.

Show Other Inspections

Displays others apart has passed or failed other inspections on the current sensor.
Right-click the menu again to see the option to hide good inspections. If that option
is checked, then only the failed inspections are displayed.
Display Timing Information
Displays timing information for each inspection on the current sensor and the total
time in milliseconds.

Region of Interest Options

Right-click in the Unwrapped Region of Interest to display the region of interest (ROI)
options menu. To stop displaying either option, right-click the menu again and un-check
the option.

Show Graphics
Displays any graphics that are selected, like vectors or edges, on the Unwrapped
Region of Interest.
178 Inspection Overview System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Region Display Mode
Gives you the option to show the original region, or the enhanced region, if it has an
enhancement.

RETRO-SPEC POPULATION VIEW GRAPH

The Retro-Spec graph is displayed when you edit a Registration, Orientation, or
Inspection.
The Retro-Spec Graph can display up to 200 parts at a time, 100 in each set. Each bar on
the graph represents a different part. A green bar means that the part has passed. A
yellow bar means that the part has exceeded the warning limit but not the reject limit. A
red bar means that the part has exceeded the reject limit. A lighter shade of green, red or
yellow will be displayed when a part is selected. To select a part, simply click on a bar in
the graph. When you click a bar, the part's unique Part Image, Unwrapped Region of
Interest, and Results will be displayed.
Population View
Displays details for up to the last 200 parts. The parts can be the last 100 run, the
latest 100 defects for the inspection, or a set of parts previously saved to the hard
drive.
Graphs with One Reject Bar
Some inspections have one reject bar on the Retro-Spec Graph. The Warning/Reject
Bar can be a minimum requirement where the part Retro-Spec value must be higher
than the reject bar in order to pass. The Warning/Reject Bar can also be a maximum
requirement where the part Retro-spec value cannot exceed the reject bar in order to
pass.
Graphs with Two Reject Bars
Some inspections have two reject bars. The part‘s value must be between the two
reject limits to be considered a good part. The example below shows an ambient
inspection with two reject bars (red) and two warning bars (yellow).

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspection Overview 179
© 2011 Pressco Technology Inc. Proprietary
 The components of the Retro-Spec graph are as follows:

1 Selected View Shows which Retro-Spec graph view is being displayed.

2 Selected Inspection Shows the type of inspection.
3 Reject Bar (red) Shows the inspection limits. Parts that fall outside the reject limits are
considered defective.
4 Warning Bar (yellow) Shows the inspection warning limits. Parts that fall outside the warning
limits are not considered defective, but are approaching reject status.
5 Reject Part Reject Parts are displayed in Red.
Warning Part Warning Parts are displayed in Yellow. [not shown in this example]
6 Passing Part Passing Parts are displayed in Green.
7 Other Results Indicator Indicates whether a part has failed or had a warning on a different
inspection. A small red box will appear under a part that has failed a
different inspection. A small yellow box will appear under a part that has
had a warning from a different inspection.
8 Save Parts Allows you to save a set of parts which can be reloaded later. You can
save the Selected Parts, Set A, or Set B. You can also choose where to
save them by clicking the Save Parts button under "Where to save?"
9 Select Parts Allows you to select a set of parts, set A or Set B, to be displayed in the
Retro-spec Graph. Clicking on either the left or right arrow will bring up the
Select Parts Menu below. You can choose from Last 100, Latest Defects,
or Custom Set.
10 Delete Part [Trash can Gives you the ability to delete a single part. Can only be used when the
icon] lock [item 11] is unlocked. To delete a part: highlight the part, then click the
trash can icon, or highlight the part then drag it to the trash can icon and
release the trackball button. A message appears above the icon stating
that the part has been deleted.
11 Lock/ Move Parts When the graph is locked, parts cannot be moved or deleted. When the
Toggles to: graph is unlocked, part sets can be modified. Parts can be saved, moved
within the same set, moved to the set on the other side of the divider, or
deleted. Dragging the part to the Select Parts arrows [item 9] will move the
part into the corresponding side. Dragging the part to the Save Parts
button will allow you to save the part. Dragging the part to the Delete Parts
button will delete the part.
12 Data Set B The parts on the right side of the divider make up data Set B.

180 Inspection Overview System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Once a part has been deleted or moved, the term **Scratch Parts** is displayed at the top
of the data set. To save the data set with your changes, click the Save Parts icon [item 8].
This will allow you to save the data set on either side of the divider, or just the selected
parts.

Retro-Spec Options
Right-click the Retro-Spec graph to see the Retro-Spec options menu.
 Note: some options are not displayed if they are not applicable to the current
inspection.

Population View
When this is checked, the Retro-Spec population view graph (on page 179) is
displayed.
Part View
When this is checked, the Retro-Spec part view graph is displayed.
Symmetric Limits
When the Retro-Spec graph has upper and lower limits (two red bars and two yellow
bars), this option keeps the upper and lower limits the same distance from nominal.
Lock Warnings to Errors
Locks the yellow warning bar to the red reject bar in the Retro-Spec graph, keeping
them the same distance apart.

Auto Select Limits

Automatically adjusts warning and reject levels to make all parts in the data set pass.
Enable Warnings
Provides a warning level (yellow) sensitivity bar. A warning level does not reject
parts, but indicates that the process is approaching the reject status. When you enable
warnings, they are enabled for all inspections for the current sensor.
System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspection Overview 181
© 2011 Pressco Technology Inc. Proprietary
 Graph Scale Mode
Change the height scale of the graph.
Limits Only displays part parameter values up to and including the current
inspection limits. This is useful when you want to zoom in on data without extra
lines on the graph. Note that the limit lines may not be displayed on the graph. As
soon as you change the parameter limits from the menu, the limit lines are displayed
again on the graph.
Limits and Data is the default mode that displays all the inspection data plus the
limit lines.
Select Data Set A or B
For each Data Set, you can select what you want to display. You can choose to
display Nothing, Last 100 Parts, Latest Defects or a set of Image Files that have been
previously saved to the computer.
See information about Saving Images (see "Saving Images through the Retro-Spec
interface" on page 145).

Select Parameter
Choose a graph to display. This is available for some inspections where you have a
choice to display different graphs. An example is Measurement Analysis, where
there are several different measurement graphs available, as shown below.

182 Inspection Overview System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 RETRO-SPEC PART VIEW GRAPH
The Part View shows specific information unique to each part. To display the Part View,
right click on a part and choose Population View, or double-click a part from the
Population View. There are different types of Part Views that vary by inspection.
 Note: not all inspections have a Part View graph available.
Shown below is the Part View of a Contrast inspection. It has a reject bar and an
Unwrapped Region of Interest. Any type of damage to the surface of the part, which can
be seen in the Unwrapped Region of Interest, will have a corresponding value on the
graph. If any part of the graph exceeds the Reject Bar, the whole part will be considered
a defective image. The Reject Bar can be dragged, changing the actual reject threshold.

Shown below is a Part View of an Ambient inspection. This Part View does not have a
reject bar but does have an Unwrapped Region of Interest. The graph does not
correspond to Gray Shades on the Unwrapped Region of Interest. The graph represents
how many pixels of each Gray Shade are found on the part.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspection Overview 183
© 2011 Pressco Technology Inc. Proprietary
Chapter 13
INSPECTIONS
This section covers regions of interest, registrations, orientations, enhancements,
analyses, and measurements. We use the term 'inspections' to include all of these items,
for simplicity.
The information in this section is valid as of software version 5.0.455.

EMPTY POCKET
The Empty Pocket feature checks to see whether a part is present or not. This is used for
applications where you must determine whether a part is present before proceeding with
inspection. A common use for this test is in Starwheel applications where the encoder is
used, based on pocket position, rather than a part present signal. Locating an empty
pocket is important for production numbers to be accurate. If an empty pocket is found,
no inspection takes place for that pocket. Otherwise, an empty pocket would be recorded
as a defect.
Notes:
You may run the Empty Pocket check on any inspection. We recommend that you
use it with an inspection that has pass/fail criteria. Ambient and Contrast inspections
are most commonly used.
You may add as many empty pocket checks to the part program as desired.
To add an Empty Pocket check to an existing part program:
1. In the inspection tree, right-click over the name of the inspection to which you want
to add the Empty Pocket check.
2. From the Inspection menu, select Enable/ Disable Empty Pocket Check. That
inspection is highlighted in blue, and will remain highlighted unless you disable the
Empty Pocket check.
Enable the Empty Pocket check Inspection with Empty Pocket check
is highlighted in cyan

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 185
© 2011 Pressco Technology Inc. Proprietary
 Enable the Empty Pocket check Inspection with Empty Pocket check
is highlighted in cyan

Statistics updates using Empty Pocket

To make sure that the statistics totals do not count empty pockets as defects, you must set
up an Empty Pocket check for all sensors in each lane. For example, if you have three
sensors in Lane 1, all three sensor part programs must contain an Empty Pocket check.
The statistics are counted as an OR function. If any of the sensors within a lane detects
an empty pocket, then that part ID is not counted in the defect statistics.

REGIONS OF INTEREST (ROI)

Regions of Interest (ROI) are the locations where the registrations, analyses, and
orientations take place. There is no inspection done in a Region of Interest. However,
there is no limit to the number of inspections that can be placed in one Region of Interest.
There are up to five region types available to set up the region of interest on a part. All
regions can be edited directly on the image (after adding them to the inspection list).
 Note: Your system (and this book) may show only those items that apply to your
application.
Ring Region (on page 187)
Polygon Region (on page 188)
Ribbon Region (on page 190)
Measure ROI (on page 193)
Adaptive Region (on page 195)

Region of Interest Compatibility Chart

The following chart shows whether each inspection depends on a certain region type.
Inspection Compatible with this Region Type
Enhancements
All Enhancement types All
Registrations
186 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Feature All except Ribbon and Loop
Center of Mass All
Hough Ring
Radial Edge Ring
Centerline Ribbon - mirrored only
Finish Location Ribbon
Template Registration All except Ribbon and Loop
Orientations
Pattern Match Ring
Template Orientation All except Ribbon and Loop
Analyses
Ambient All
Shape Check Adaptive
Contrast All
Measurement All except Polygon or Measure ROI
Light Meter All
Fill Height Measure ROI, two regions
Measure Extract Measure ROI
Distribution All
Label Skew Extract Measure ROI
Dimensions
Distance These do not use regions; they get data
from other inspections.
Angle
Correlations (not available)

Ring Region
The Ring region is circular or donut-shaped. You can create arcs or multiple arc
segments in the region. The inner and outer radii are adjustable, and the region's position
is adjustable.

To add a Ring Region:

1. If you plan to use Arcs for the Ring Region, place an Orientation (see
"Orientations" on page 228) in the inspection tree. If you want the region to be
circular or donut-shaped, skip the Orientation.
2. Highlight the Orientation name in the inspection tree (if applicable).
3. Right-click in the inspection tree to see the Inspection menu.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 187
© 2011 Pressco Technology Inc. Proprietary
 4. From the Inspection menu, select Add > Region > Ring. Re-name it to something
more meaningful to you.
5. The Ring Menu is displayed and the ring is shown on the image. (The menu is
described below) Adjust the placement of the ring and parameters as necessary.
Ring menu

The following parameters can be set graphically (on the image), or through a slider bar or
numeric keypad, which pop up when you click on a numeric value. Also refer to more
information about Editing Parameters (on page 176).
X and Y position
Horizontal and vertical position of the center of the ring on the image.
Inner Radius
Size of the inner ring.
Thickness
The thickness of the ring; outer radius minus inner radius.
Use Arcs
Allows you to inspect an arc instead of the whole region. The system will inspect a
segment of the region between the Start and Stop angles. Make sure you have an
Orientation in the job prior to using arcs. This will ensure that the inspection region
is placed on the same location of the part regardless of the part‘s orientation.
The following parameters are available when Use Arcs is enabled.
Start Angle
The start angle of the region.
Stop Angle
The stop angle of the region
Arc Count
Set the number of segments you want to create in the region.
Arc Alignment
Not currently used.

188 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Polygon Region
Similar to the Ribbon Region (on page 190), the Polygon Region is a customizable
region that is used for:
free-form inspection areas on a part
areas that do not fit a circle or other standard inspection region
 Note: we recommend that you place a Registration and Orientation (if applicable)
prior to adding a polygon region. This will ensure that the polygon is placed
correctly on the part, regardless of the part's placement or rotation.

To add a Polygon Region:

1. Make sure that the part program has a registration and/or orientation in place to
ensure proper placement of the polygon on all inspected parts.
2. Highlight the Registration or Orientation name in the inspection tree.
3. Right-click in the inspection tree to see the Inspection menu.
4. From the Inspection menu, select Add > Region > Polygon. Re-name it to something
more meaningful to you.
5. A "NEW POLYGON: Click to add points" message is displayed in the large image
area, and the Polygon Menu is displayed. (The menu is described below) Click
anywhere in the image to start the polygon.
6. Continue clicking with the yellow boxes (polygon points) to create a polygon region.
You may create as many points as you like.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 189
© 2011 Pressco Technology Inc. Proprietary
 7. When you want to close the region, click on the first box that you placed. The region
closes and is filled in for you.

8. Make any necessary adjustments from the menu (described below). You can make
adjustments to the region, duplicate it, or rotate it from the menu.
To edit the polygon region:
Right-click the image to view the Image Options (on page 158) menu. Use Edit Mode to
Delete, Add, or Move any polygon point or the entire region.
Polygon menu

Repeat Polygons
Create duplicate copies of the original polygon. Allows from 1 to 10 polygons that
are centered and rotated around the registered position.
Repeat Count
(Available when using multiple polygons) Choose the number of duplicate polygons
to place on the image. The system automatically distributes these polygons around
the image. A common use for this feature is for the feet of a PET bottle.
Rotate Polygon
Rotate the polygon around the center of the polygon. If you have duplicate polygons,
they are also rotated.
Expand or Contract
Resize the region. A negative number contracts the region, and a positive number
expands the region.
Note: be careful not to contract the region too much. This will distort the
original shape.

190 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Ribbon Region
Similar to the Polygon Region (on page 188), the Ribbon Region is a customizable
region and can come in two different forms: ribbon, and loop. This type of region is used
for:
free-form inspection areas on a part
areas that do not fit a circle or other standard inspection region
 Note: we recommend that you place a Registration and Orientation (if applicable)
prior to adding a Ribbon region. This will ensure that the ribbon is placed correctly
on the part, regardless of the part's placement or rotation.

1 Ribbon - a customizable region that does not close, similar to a rubber

band that has been cut. Thickness remains the same throughout the
region.
2 Loop - a closed version of the ribbon region, similar to a rubber band.
Thickness remains the same throughout the region.

To add a Ribbon Region:

1. Make sure that the part program has a registration and/or orientation in place to
ensure proper placement of the region on all inspected parts.
2. Highlight the Registration or Orientation name in the inspection tree.
3. Right-click in the inspection tree to see the Inspection menu.
4. From the Inspection menu, select Add > Region > Ribbon. Re-name it to something
more meaningful to you.
5. A "NEW RIBBON: Click to add points" message is displayed in the large image
area, and the Ribbon Menu is displayed. (The menu is described below) If you want
to change the ribbon type to Loop, use the Ribbon Style drop-down item in the
menu.
6. Click anywhere in the image to start the ribbon.
7. Continue clicking with the yellow boxes (ribbon points) to create a ribbon region.
You may create as many points as you like.
8. When you want to close the region, right-click on the image to view the Image
Options menu and select Complete New Ribbon. The region closes and is filled in
for you.
9. Make any necessary adjustments from the menu (described below). You can make
adjustments to the region, duplicate it, or rotate it from the menu.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 191
© 2011 Pressco Technology Inc. Proprietary
 To edit the ribbon region:
Right-click the image to view the Image Options (on page 158) menu. Use Edit Mode to
Delete, Add, or Move any ribbon point or the entire region.
Ribbon menu

Ribbon Style
Choose between Ribbon or Loop as described above.
Ribbon Width
Set the width of the region.
Repeat Ribbons
Create duplicate copies of the original ribbon. Allows from 1 to 10 ribbons that are
centered and rotated around the registered position.
Mirror Ribbon
(Only used when Repeat Ribbons is disabled) Create a flipped duplicate of the
region. This is typically used for the Centerline (on page 222) Registration where
two sides are being searched for.
Mirror Angle
(Only used with Mirror Ribbon) Flip the mirrored region horizontally (90 degrees),
vertically (zero degrees), or any angle in between.
Mirror Offset
(Only used with Mirror Ribbon) Move the mirrored region further or closer together.
Repeat Count
(Available when using multiple ribbons) Choose the number of duplicate ribbons to
place on the image. The system automatically distributes these ribbons around the
image. A common use for this feature is for the feet of a PET bottle.
Rotate Ribbon
Rotate the ribbon around the center of the ribbon. If you have duplicate ribbons, they
are also rotated.
Expand or Contract
Resize the region. A negative number contracts the region, and a positive number
expands the region.
Note: be careful not to contract the region too much. This will distort the
original shape.

192 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Measure ROI
Measure ROI(s) is a region that is intended to be used in measurement type operations
(such as Label Skew Extract (on page 263), Measure Extract (on page 256), and Fill
Height (on page 251)).

To add a Measure ROI Region:

 Tip: We recommend that you first add a standard region of interest and registration
to locate a reference point on the part. The Measure ROI region will then follow the
correct location on the part.
1. Highlight the Registration name (if one is available) in the inspection tree.
2. Right-click in the inspection tree to see the Inspection menu.
3. From the Inspection menu, select Add > Region > Measure ROI. The Measure ROI
region is added to the inspection tree. Re-name it to something more meaningful to
you.
4. The Measure ROI menu is displayed and the region is shown on the image. (The
menu is described below) Adjust the placement of the region and parameters as
necessary.
Measure ROI menu

Region Count
Leave this set at One Region unless you have a Fill Height application. Most
measurements require one region. Fill Height applications require two regions: one
for reference, and one for fill level.
Region 1
Contains the settings for Region 1.
Width
Adjust the width of the region. You can also click on the image and adjust the region
graphically (if Enable Region Editor is checked in the Image Options menu).
The Measure ROI is a two point polygon ribbon region. Refer to the illustration below.
The end points [1] adjust the length of the ribbon. The point on the side of the region [2]
adjusts the width of the ribbon. The diamond [3] indicates the direction towards which
the vectors are searching.
 Note: for the image below, both Enable Region Editor and Enable Region Size are
checked in the Image Options menu. You view the yellow boxes and points when you
click on the image to adjust the region size and/or position.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 193
© 2011 Pressco Technology Inc. Proprietary
 1 End points of the ribbon region
2 Point to adjust the width of the region
3 Indicates the direction towards which the vectors are searching

ADDITIONAL MENU ITEMS FOR TWO REGIONS

Vertical Lock Mode, Horizontal Lock Mode, and Sizing Lock Mode
Choose whether to move the two regions independently, or to lock the regions (move
the regions together). When you choose to mirror the regions, the regions move in
opposite directions.
IMAGE OPTIONS MEASURE ROI
When you right-click the image you will see a slightly different image options menu for
Measure ROI. Most of the menu items are the same as in the default image options (on
page 158) menu. The last three items are different.

Enable Region Move

Enable Region Editor must be enabled before you can move the region. Click and
drag the entire region.
Enable Region Size
Adjust the region size by clicking on the image and moving the yellow points.
Enable Region Direction
Click a diamond on any side of the ribbon to change the search direction for the
Measure Extract (on page 256) inspection.
Close Menu
Until you use Close Menu or click on the image, the Image Options menu stays open
so that you can select multiple options.

194 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Adaptive Region
This is a region that is built from the edge points found in registrations (except from
Template Registration). The region adapts to whatever edge points are found. It can
follow the shape of your part.

Series IV users: this is similar to Tracker or Shape Adapt registrations.

 Note: Adaptive Region can be added only after one or more Registrations (on page
211).

To add an Adaptive Region:

1. Make sure at least one Registration (see "Registrations" on page 211) has been
added to the inspection tree.
2. Highlight the Registration name in the inspection tree.
3. Right-click in the inspection tree to see the Inspection menu.
4. From the Inspection menu, select Add > Region > Adaptive. The Adaptive region is
added to the inspection tree. Re-name to something more meaningful to you.
5. The Adaptive Menu is displayed and the region is shown on the image. (The menu is
described below) Adjust the placement of the region and parameters as necessary.
Adaptive menu

Creation Mode
Choose whether to have the region adapt to each part as it is inspected [Adapting
Region], or to find a region once and use it for all parts [Fixed Region]. Different
menu parameters are available. Fixed Region is described below.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 195
© 2011 Pressco Technology Inc. Proprietary
 Region Style
Choose the type of region you want to create from the registration results. Use the
one best suited to the area you are inspecting. The options are described below.
Fit to Circle - A donut-shaped region is created.

 Note: For descriptions of shapes, also refer to Polygon Region (on page 188) and
Ribbon Region (on page 190). The difference in the Adaptive Region is that the
shape is created using found registration points, rather than manually placed points,
as is done in the standard Polygon or Ribbon Regions.
Polygon - a free-form shape is created and filled in.
Ribbon - a free-form ribbon shape is created. The ends are open. You specify the
width of the region.
Loop - a free-form shape is created. The ends are connected. You specify the width
of the region.
Custom 2 Sided Polygon - a free-form shape is created and filled in. This shape
should only be used after a Centerline registration. You have the option of creating
separate offsets for each side. A common use for this is Preform sidewall
inspections, where there is a dark area on either side of the preform in cameras one
and three. With Custom 2 Sided Polygon, you could create the region to ignore that
dark area.
Edge Offset
Specify how many pixels away from the found registration points the Adaptive
Region should be.
Region Offset Side 2
(Used with Custom 2 Sided Polygon) Allows you to create a different offset for one
side of the part. This is normally used for Preform sidewall inspections.
Correction Mode
Allows you to correct the edge positions from one of the available techniques
No Correction - uses the original registration positions.
Simple Smoothing - smooths the edges of the region.
Circular Smoothing - smooths the edges to form a circle.
Dual Edge Correction - (applies additional Correction Settings) This mode should
only be used after a Centerline registration. It corrects missing and bad points in the
two sets of edge locations (the two sides of the part).
Bad Point Removal - uses an additional Correction Sensitivity parameter.
Removes bad points from the found edge positions. If an edge point does not fall
within the specified sensitivity, it is removed from the Adaptive region.
Correction Sensitivity
(used with Bad Point Removal) Adjust the sensitivity of the edge positions between
10 and 500. A smaller number means greater sensitivity.
DIAGNOSTICS
Show Found Edges
Display the found edges on the image.
Show Corrected Edges
Show the edges that were corrected using Correction Mode.
196 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Show Region Edges
Show the location of the edges after using Region Offset.
CORRECTION SETTINGS (USED WITH DUAL EDGE CORRECTION)
Maximum Deviation
Specify how many pixels an edge can be away from the found edge before applying
edge correction.
Learn Cross Section
Click the Learn Distances button to determine normal edge locations for that part.
Fixed Region Adaptive menu

When you choose Fixed Region, the Intellispec will find the shape of the part once, then
use that shape region for all remaining parts.
To set a Fixed Region:
1. Select a Region Style.
2. Set the remaining parameters below Region Style as appropriate for your part.
3. Click the Get Region button to set the region based on the current part.
Lock Region
Click the Get Region button (after setting the Region Style and other parameters) to
set the region based on the current part. The Intellispec finds the region edges for the
current part and creates a polygon or other region style. That region is then used for
inspection of all subsequent parts.
Region Style
Choose the type of region you want to create from the registration results. Use the
one best suited to the area you are inspecting. The options are described below.
Fit to Circle - A donut-shaped region is created.

 Note: For descriptions of shapes, also refer to Polygon Region (on page 188) and
Ribbon Region (on page 190). The difference in the Adaptive Region is that the
shape is created using found registration points, rather than manually placed points,
as is done in the standard Polygon or Ribbon Regions.
Polygon - a free-form shape is created and filled in.
Ribbon - a free-form ribbon shape is created. The ends are open. You specify the
width of the region.
Loop - a free-form shape is created. The ends are connected. You specify the width
of the region.
Custom 2 Sided Polygon - a free-form shape is created and filled in. This shape
should only be used after a Centerline registration. You have the option of creating
separate offsets for each side. A common use for this is Preform sidewall
inspections, where there is a dark area on either side of the preform in cameras one
and three. With Custom 2 Sided Polygon, you could create the region to ignore that
dark area.
System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 197
© 2011 Pressco Technology Inc. Proprietary
 Region Width
(Used with Fit to Circle, Ribbon, and Loop) Specify how many pixels wide the
region should be.
Edge Offset
Specify how many pixels away from the found registration points the Adaptive
Region should be.
Region Offset Side 2
(Used with Custom 2 Sided Polygon) Allows you to create a different offset for one
side of the part. This is normally used for Preform sidewall inspections.
Ribbon/Loop Offset Style
(Used with Ribbon and Loop) Distance Offset works best with small offsets.
Proportional Scaling works better with large offsets and keeps the shape nicely.

ENHANCEMENTS
Enhancements are used to alter images for the purpose of better defect detection, or for
making certain features stand out. They are applied to any region type and you can add as
many as needed to a region.
Notes:
The unwrapped image (displayed while you are editing an inspection) shows the
effect of the enhancement. You will not see any difference in the main image.
Enhancements are added prior to inspections
The order in which you place enhancements is important. The effect of most
enhancements is cumulative, except for Color Distance and Color Extraction. Color
Distance and Color Extraction work independently of other enhancements.
To determine the best enhancement for your inspection, it may take some
experimentation. Use the enhancement that brings out the defects or features best for
your part.
To add an enhancement:
1. Make sure at least one region (see "Regions of Interest (ROI)" on page 186) is
placed on the image.
2. Right-click over the inspection tree and select Insert or Add > Enhancement.
3. Choose the desired enhancement from the menu.
The available enhancements are:
Subtract Bias (on page 199)
Clipping (on page 199)
Stretch Grayshades (on page 201)
Binary (on page 202)
Gamma Correction (on page 203)
Grow Dark Areas (on page 204)
Grow Light Areas (on page 205)
Absolute Difference (on page 206)
Color Distance (on page 207)
Color Extraction (on page 209)
 Note: Your system (and this book) may show only those items that apply to your
application.
198 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Subtract Bias
Subtract Bias is a simple value subtraction across the entire region. Subtract the given
value from all pixels in the region. The example below shows the result (bottom image)
of subtracting a gray level of 80 from the top image.

To add a Subtract Bias enhancement:

1. Make sure at least one region is placed in the inspection tree.
2. Right-click in the inspection tree to see the Inspection menu.
3. From the Inspection menu, select Add > Enhancement > Subtract Bias. The
enhancement is added to the inspection tree. Re-name the inspection to something
more meaningful to you.
4. The Subtract Bias menu is displayed and the region is shown on the image. (The
menu is described below) Adjust the parameters as necessary.

Subtract Bias tab

Use Bias
Enable the enhancement.
Black Level
Set the gray level value to subtract from the original value of each pixel in the region
of interest.

Clipping
Clipping is used to change gray shades to a specified value. It allows the system to ignore
light reflections or normal grain in a part, to provide easier defect detection.
To add a Clipping enhancement:
1. Make sure at least one region is placed in the inspection tree.
2. Right-click in the inspection tree to see the Inspection menu.
3. From the Inspection menu, select Add > Enhancement > Clipping. The enhancement
is added to the inspection tree. Re-name it to something more meaningful to you.
4. The Clipping menu is displayed and the region is shown on the image. (The menu is
described below) Adjust the parameters as necessary.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 199
© 2011 Pressco Technology Inc. Proprietary
 Clipping menu

Clipping mode
The available modes are as follows - also refer to the illustration below:
Disabled [item 1] – no clipping.
Clip Black Level [item 2]– set a dark gray shade value. A dark clipping value of 100
would take all pixels with gray levels of 0-99 and make them a gray level of 100.
Clip White Level [item 3] – set a light gray shade value. A light clipping value of
150 would take all pixels with gray levels of 151-255 and make them 150.
Clip Black and White Levels [item 4] – set both dark and light levels.
Below are grayscale plots of the area to illustrate the effects of clipping.

1 Original grayscale plot- Clipping Disabled

2 Clip Black Level - example uses 100 as black level
3 Clip White Level - example uses 150 as white level
4 Clip Black and White Levels - example uses 100 as black level and 150 as
white level
You will see the effects of clipping in the Unwrapped Region of Interest, as shown
below.

200 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 1 Region
2 Clipping Disabled
3 Clip Black and White Levels applied

Stretch Grayshades
Stretch Grayshades is used when you want to make one feature stand out from the rest of
the part. This technique works essentially how it sounds: it allows you to zoom in on a
specific range of gray shades and stretch them to the full 0 - 255 range. You will see the
effects of stretching gray shades in the Unwrapped Region of Interest.
To add a Stretch Grayshades enhancement:
1. Make sure at least one region is placed in the inspection tree.
2. Right-click in the inspection tree to see the Inspection menu.
3. From the Inspection menu, select Add > Enhancement > Stretch Grayshades. The
enhancement is added to the inspection tree. Re-name it to something more
meaningful to you.
4. The Stretch Grayshades Menu is displayed and the region is shown on the image.
(The menu is described below) Adjust the parameters as necessary.

Stretch Grayshades
Check the box to enable the enhancement.
Stretch Technique
Enables you to zoom in on any range of gray shades.
Use Min/Max of Region - the system uses the lowest gray shade found and the
highest gray shade found, and stretches that range from 0 to 255.
Use Grayshade Percentiles - Specify lower and upper values in the Shades of
Interest box in terms of percentage of pixels. The system counts the number of pixels
of each gray shade and puts them into bins. An example is when 29-65 is used for
Shades of Interest. The system determines (a) the gray shade where 29% of the
pixels fall, and (b) the gray shade where 65% of the pixels fall. The system then
takes the pixels at gray shades (a) and (b) and sets them to 0 and 255. The gray
shades in between (a) and (b) are stretched from 1-254.
Use Absolute Grayshades - Specify lower and upper values in the Shades of
Interest box. The system sets all pixels at or below the lower specified value to black,
pixels at or above the higher specified value to white, and the values in between are
stretched from grayshades 1 to 254.
Shades of Interest
Define the gray shade range that you want to stretch. Adjust so that the desired
feature stands out in the image.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 201
© 2011 Pressco Technology Inc. Proprietary
 Stretch Grayshades example
In the example below, we use the mold line as a reference point. We want that mold line
to stand out, so we use Stretch Grayshades.

1 Original image
2 Unwrapped region of interest with no enhancement
3 Unwrapped region of interest with Use Min/Max of Region applied
4 Unwrapped region of interest with Use Grayshade Percentiles and Shades
of Interest applied

Binary
This enhancement takes all pixels at or above a threshold and makes them white, and all
pixels at or below the threshold and turns them black. This can help certain features to
stand out. An example of a Binary enhancement is shown below.

1 Unwrapped region of interest with no enhancement

2 Unwrapped region of interest with Binary Enhancement applied

To add a Binary Enhancement:

1. Make sure at least one region is placed in the inspection tree.
2. Right-click in the inspection tree to see the Inspection menu.
3. From the Inspection menu, select Add > Enhancement > Binary. The enhancement is
added to the inspection tree. Re-name it to something more meaningful to you.
4. The Enhancements menu is displayed and the region is shown on the image. (The
menu is described below) Adjust the parameters as necessary.

202 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Binary enhancement tab

Use the technique and threshold that best suits your application.
Binary Technique
Choose a technique to set the grayshade limits. Choose between Fixed Grayshade
and Adaptive Grayshade. Set the related threshold as described below.
Adaptive Threshold
The system computes the ambient level for the region. Set Adaptive Threshold to the
percentage of pixels to use in the region. This is similar to the Peak Percentile
technique used in the Ambient (on page 232) inspection.

1 Gray level - choose a percentage

2 Pixels in the histogram of the image

Fixed Threshold
The system uses the number you enter. All pixels at or below the threshold will be
turned black. All pixels at or above the threshold will be turned white.

Gamma Correction
Gamma Correction lets you reveal detail in a low-contrast image without significantly
affecting the shadows or highlights.The example below shows the results of the Gamma
Correction enhancement applied.

1 Original image
2 Decreased contrast - Gamma value less than one
3 Increased contrast - Gamma value greater than one

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 203
© 2011 Pressco Technology Inc. Proprietary
 To add a Gamma Correction enhancement:
1. Make sure at least one region is placed in the inspection tree.
2. Right-click in the inspection tree to see the Inspection menu.
3. From the Inspection menu, select Add > Enhancement > Gamma Correction. The
enhancement is added to the inspection tree. Re-name it to something more
meaningful to you.
4. The Gamma Correction menu is displayed and the region is shown on the image.
(The menu is described below) Adjust the parameters as necessary.

Gamma Correction tab

Gamma Correction
Enable the enhancement.
Gamma
Change the contrast of the image. Values less than one decrease contrast, and values
greater than one increase contrast.

Grow Dark Areas

This enhancement will grow the dark areas of the region. This can be used to remove
reflections, or shrink bright spots on the image. The example below shows how Grow
Dark Areas enhances the image.

1 Normal image
2 Image with Grow Dark Areas applied

To add a Grow Dark Areas enhancement:

1. Make sure at least one region is placed in the inspection tree.
2. Right-click in the inspection tree to see the Inspection menu.
3. From the Inspection menu, select Add > Enhancement > Grow Dark Areas. The
enhancement is added to the inspection tree. Re-name it to something more
meaningful to you.
4. The Grow Dark Areas menu is displayed and the region is shown on the image. (The
menu is described below). Adjust the parameters as necessary.

204 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Enhancements tab

Grow Dark Areas

Enable the enhancement.
Growth Rate
Increase this value to grow the areas more.
Max. Shade Delta
Specify the largest gray shade difference that can be applied to a pixel during area
growth. If this value is set to zero, then the resulting pixel can be set to any value.

Grow Light Areas

Grow Light Areas is the opposite of the Grow Dark Areas enhancement. Small dark
defects can be blurred out and therefore ignored. The example below shows how Grow
Light Areas enhances the image

1 Normal image
2 Image with Grow Light Areas enhancement applied

To add a Grow Light Areas enhancement:

1. Make sure at least one region is placed in the inspection tree.
2. Right-click in the inspection tree to see the Inspection menu.
3. From the Inspection menu, select Add > Enhancement > Grow Light Areas. The
enhancement is added to the inspection tree. Re-name it to something more
meaningful to you.
4. The Grow Light Areas menu is displayed and the region is shown on the image. (The
menu is described below) Adjust the parameters as necessary.

Enhancements tab

Grow Light Areas

Enable the enhancement.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 205
© 2011 Pressco Technology Inc. Proprietary
 Growth Rate
Increase this value to grow the areas more.
Max. Shade Delta
Specify the largest gray shade difference that can be applied to a pixel during area
growth. If this value is set to zero, then the resulting pixel can be set to any value.

Absolute Difference
Absolute Difference will subtract a value from all of the gray shades in an image. The
resulting gray shade value is an absolute value, so that value is always positive. For
example, assume Absolute Difference is set at 100, and two original pixel values are 175
and 25. When the system subtracts 100 from each, the resulting values are both 75 [175 -
100 = 75, and 25 - 100 = 75] (using the absolute value).
The example below shows an Absolute Difference of 100 applied.

1 Normal image
2 Image with Absolute Difference enhancement applied

To add an Absolute Difference enhancement:

1. Make sure at least one region is placed in the inspection tree.
2. Right-click in the inspection tree to see the Inspection menu.
3. From the Inspection menu, select Add > Enhancement > Absolute Difference. The
enhancement is added to the inspection tree. Re-name it to something more
meaningful to you.
4. The Enhancements menu is displayed and the region is shown on the image. (The
menu is described below) Adjust the parameters as necessary. Experiment with
values to enhance features you want to see more clearly on your part.

Enhancements tab

Absolute Difference
Enable the enhancement.
Gray Level
The resulting pixel gray shade is the absolute difference between this value and the
original pixel gray shade.

206 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Color Distance
Color Distance is used to provide more contrast between similar colors on an image to
make certain defects or features stand out. This enhancement only applies to images
produced by color cameras. It is similar to the Absolute Difference (on page 206)
enhancement that is used for grayscale images.
 Note: Color Distance works oppositely from Color Extraction. Experiment between
the two enhancements to see which one works better for your application.
Color Distance evaluates all pixels in the search region against the selected color and
translates that value to a gray level. The closer a color is to the selected color, the darker
the pixel. The further away a color is from the selected color, the lighter the pixel. This
difference in pixel appearance is only displayed in the unwrapped region - not the full
part image.
The example below shows a purple part against a blue belt. The region of interest is
highlighted in the image for illustration purposes. Notice that, in the unwrapped region
[item 1], the purple and blue colors are very similar when translated to grayscale, making
it difficult to detect the part edges. We can apply a Color Distance enhancement to this
image to make purple and blue stand out from each other, as shown in the unwrapped
image [item 2].

1 Normal image
2 Image with Color Distance enhancement applied

To add a Color Distance enhancement:

1. Make sure at least one region is placed in the inspection tree.
2. Right-click in the inspection tree to see the Inspection menu.
3. From the Inspection menu, select Add > Enhancement > Color Distance. The
enhancement is added to the inspection tree. Re-name it to something more
meaningful to you.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 207
© 2011 Pressco Technology Inc. Proprietary
 4. The Color Distance menu is displayed and the region is shown on the image. (The
menu is described below) Adjust the parameters as necessary. Experiment with
values to enhance features you want to see more clearly on your part.

Color Distance tab

Color Distance
Enable the enhancement.
Distance Technique
Select how to determine the distance between two colors.
RGB - Uses the red, green, and blue components of a color.
Delta E - Not currently available.
Color Picker
Choose the desired reference color.
To use Color Picker:
1. Click the Color Picker button to begin selecting a color from the image. Click in the
image again until the cursor becomes a cross-hair with an eye dropper.

2. Using the center of the cross-hair, click in the image over the color you want to
compare. The box next to Color in the menu displays your selected color.
3. When you have selected the desired color, click the Color Picker button again to
complete the selection.
Color
The box displays the selected color.

208 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Click on this menu line to display a drop-down menu array of colors from which to
choose. This can be used instead of using the Color Picker.

Color Extraction
Color Extraction allows you to choose a color and then the system lightens all pixels with
that color. This makes certain defects or features stand out. This enhancement only
applies to images produced by color cameras.
 Note: Color Distance works oppositely from Color Extraction. Experiment between
the two enhancements to see which one works better for your application.
When the Intellispec enhances the image, pixels containing the selected color will appear
brighter. This difference in pixel appearance is only displayed in the unwrapped region -
not the full part image. The color pixels are translated to grayscale values and then
inspected. This is what you see in the unwrapped image.
The example below shows a purple part against a blue belt. The region of interest is
highlighted in the image for illustration purposes. Notice that, in the unwrapped region
[item 1], the purple and blue colors are very similar when translated to grayscale, making
it difficult to detect the part edges. We can apply a Color Extraction enhancement to this
image to make purple and blue stand out from each other, as shown in the unwrapped
image [item 2].

1 Normal image

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 209
© 2011 Pressco Technology Inc. Proprietary
 2 Image with Color Extraction enhancement applied

To add a Color Extraction enhancement:

1. Make sure at least one region is placed in the inspection tree.
2. Right-click in the inspection tree to see the Inspection menu.
3. From the Inspection menu, select Add > Enhancement > Color Extraction. The
enhancement is added to the inspection tree. Re-name it to something more
meaningful to you.
4. The Color Extraction menu is displayed and the region is shown on the image. (The
menu is described below) Adjust the parameters as necessary. Experiment with
values to enhance features you want to see more clearly on your part.

Color Extraction tab

Color Extraction
Enable the enhancement. Use one of the following selections to choose the color you
want to enhance.
Color Extraction Technique
From the drop-down menu, select the color closest to the color you want to enhance.
If you select a Raw color such as red, then the Intellispec enhances only the red
pixels and ignores the green and blue elements of the image.
Technique Picker
Choose a reference color from the image. The system will determine the closest color
to the choices available. Note that the system has a limited set of color filters.
To use Color Picker:
1. Click the Technique Picker button to begin selecting a color from the image. Click
in the image again until the cursor becomes a cross-hair with an eye dropper.

2. Using the center of the cross-hair, click in the image over the color you want to
enhance. The menu item next to Color Extract Technique is updated to reflect the
selected color.
3. When you have selected the desired color, click the Technique Picker button again
to complete the selection.

210 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 REGISTRATIONS
A registration compensates for part movement by calculating the reference point on the
part. All analyses follow a registration.
 Note: you must first place a Region of Interest (see "Regions of Interest (ROI)" on
page 186) where you want the Registration to take place.
Available registrations include:
Feature (on page 211)
Center of Mass (on page 213)
Hough (on page 216)
Radial Edge (on page 219)
Centerline (on page 222)
Finish Location (on page 225)
Template Registration (on page 228)
 Note: Your system (and this book) may show only those items that apply to your
application.

Hough vs. Radial Edge

This topic is intended to help you decide whether to use a Hough or Radial Edge
registration for your round parts.
Use the registration that best fits your needs.
Hough (on page 216) Radial Edge (on page 219)
Finds edges on not quite round Finds edges on round parts
parts
Works on incomplete circular Works on complete circular features
features
Takes slightly more processing time Faster

Feature
This registration searches for the center of a specific feature that may not fall into a
standard inspection shape. It looks for all the pixels within a specified gray shade range.
Then you can choose whether to select the center from all the found features or just the
largest feature. Alternately, you may restrict a feature size to determine the center; the
found feature does not need to be the largest feature. It also allows you to count all the
found features and reject the part if there are too many or too few. This can work on any
region type.

Series IV users: this is similar to Blob Registration.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 211
© 2011 Pressco Technology Inc. Proprietary
 The example below shows a Feature registration to find the largest feature. The center of
the largest feature is used as the registration point.

To add a Feature Registration:

1. Make sure at least one region of interest has been added to the inspection tree.
2. Right-click in the inspection tree to see the Inspection menu.
3. From the Inspection menu, select Add > Registration > Feature. The Feature
registration is added to the inspection tree. Re-name it to something more meaningful
to you.
4. The Feature Menu is displayed and the region is shown on the image. (The menu is
described below) Adjust the placement of the region and parameters as necessary.
Feature menu

Center Detection
Choose whether to use the largest feature found, or all features.
Feature Gray Scale
Set the range of gray shades of the feature you want to locate.
Feature Size
Set the allowable size of the feature you want to locate.
Show Features
Highlights the found features on the image.
Check Feature Area
Checks the area of the feature to see that it is within the specified tolerance.
Allowed Area
[only available if Check Feature Area is enabled] The tolerance (in pixel area) of the
feature you want to locate.

212 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Nominal
[only available if Check Feature Area is enabled] The ideal size (in pixel area) of the
feature you want to locate.
Nominal Area Learn
[only available if Check Feature Area is enabled] Click the Learn button to
automatically determine the area of the feature.
Check Feature Count
Checks to see that the correct number of features is found.

Center of Mass
Center of Mass is a simple edge center routine that will take the average of all found
edges and use that as the center position. This can work on any region type.
 Tip: Center of Mass can be used to find edges before an Adaptive Region (on page
195) to assist in locating the adapted region.
An example of a Center of Mass registration is shown below. This registration works
with almost any shape. The center of the part is marked with a large magenta "X."

 Note: the center is computed from all found edges. If bad edges are found from a
defective part, those edges would be used in the center computation.

To add a Center of Mass registration:

1. Make sure a Region of Interest has been added to the inspection tree. This inspection
will work with any region type.
2. Right-click in the inspection tree to see the Inspection menu.
3. From the Inspection menu, select Add > Registration > Center of Mass. The
registration is added to the inspection tree. Re-name it to something more meaningful
to you.
4. The Center of Mass menu is displayed and the region is shown on the image. (The
menu is described below) Adjust the placement of the region and parameters as
necessary.

To set up the Center of Mass registration:

1. Make sure the region surrounds the feature that you want to locate.
2. Go to the Edge Location menu and select an Edge Polarity. If you are searching for
a light edge against a dark background, choose Dark to Light.
3. Go back to the Center of Mass menu and select a Center Technique.
4. If necessary, change the Search Direction (check the Flipped box) to make the
search vectors go in the opposite direction.
5. Adjust other parameters as necessary. The menu is described below.
System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 213
© 2011 Pressco Technology Inc. Proprietary
 Center of Mass tab

Center Technique
Choose the best technique to find the center.
Center of Mass - Find the center of mass of the total area enclosed by all edges. In
most cases, this is the more accurate technique, but it may fail if the part is shaped
irregularly, or if you are trying to find edges on a linear feature.
Average of Edges - Use for linear features or if the Center of Mass technique does
not work for your part. This technique finds the average location of all individual
edges. Average of Edges works better for ribbon types of regions.
Search Vector Count
Set the number of search vectors to locate the feature on the container. More vectors
provide a more accurate search, but also take more processing time.
Search Direction
If the box is checked, the search changes to the opposite direction.
Region Extraction
Choose how the Intellispec should read the information from the region. This usually
depends on the shape of your region.
Note: some inspections do not use all of these options
The illustration below shows how the information is read by each method. Note that
these shapes are examples only - your region does not have to match the shape.

1 Read Horizontally - Extract the region horizontally - 90 degrees

with respect to orientation.
2 Read Vertically - Extract the region vertically - parallel with
respect to orientation.
3 Read Circularly - Extract in a circular fashion around the region.

214 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 4 Read Radially - Extract region in a radial direction.
5 Read Horizontally and Vertically - Extract the region both
horizontally and vertically (with respect to orientation). This is
used in special cases.

Show Edges
Display the found edges on the image.
Qualifying Percent Limits
The percentage of edges that must be part of the target circle. If there are not enough
found edges on the target circle, this registration will fail. This can be set lower if
you expect large changes in sample size (less sensitive). It can be set higher if the
size of your product should not vary (more sensitive).
AREA SETTINGS
Click the Learn button to determine the nominal area (in pixels) for your part.
Area Range
Adjust the range allowed for your part. You may also adjust the values on the
Retro-Spec graph.
Nominal
The ideal area.
Learn Nominal Area
Click the Learn button to determine the nominal area for your part.
Edge Location tab
This menu determines what kind of edges the system should look for.

Edge Polarity
The type of edge for which you want the system to look – Light to Dark, Dark to
Light, or Either. For example, if the feature you want to find is very bright, choose
Dark to Light.
Edge Gradient
The minimum and maximum difference in gray shades, between two pixels, to be
considered an edge.
Edge Delta
The distance between pixels being compared when seeking an edge. A higher Delta
value increases inspection sensitivity because it finds more edges.
Edge Size
Indicates how many pixels in a row to compare (1 to 1, 2 to 2, etc.). The larger the
Edge Size, the stronger the edge will need to be. This parameter acts like a filter that
looks at a length in pixels before and after the edge.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 215
© 2011 Pressco Technology Inc. Proprietary
 Use Subpixel
Finds edges based on their subpixel location, rather than rounding off to the nearest
pixel. This gives greater centering accuracy.

Hough
This registration locates a circular feature within an image and computes the center point
of that feature. It also works with features that are not quite round. An important strength
of this registration is that the feature you wish to find does not need to fit completely
within the camera image. As long as a good portion of the feature can be found within
the image, the computed center point is accurate. It also works well if the feature you
wish to find is not clearly defined for 360 degrees.
 Note: Hough registration only works with a Ring region.
Hough registration locates edges on the desired feature and computes the best center
position based on these edges.

1 Feature (white circle) that we are searching for. This feature is partially
outside of the camera view.
2 Found center of the feature
3 Bounding rectangle. The center must be found within the rectangle.

To add a Hough registration:

1. Make sure a Ring Region (on page 187) of Interest has been added to the inspection
tree.
2. Right-click in the inspection tree to see the Inspection menu.
3. From the Inspection menu, select Add > Registration > Hough. The registration is
added to the inspection tree. Re-name it to something more meaningful to you.
4. The Hough menu is displayed and the region is shown on the image. (The menu is
described below) Adjust the placement of the region and parameters as necessary.
To set up the Hough registration:
1. Make sure the Ring region surrounds the feature that you want to locate. Adjust the
ring with the parameters in the Ring menu (or the Region Editor on the image) if
necessary.
2. In the Hough menu select a Search Direction. Flipped means that the vectors search
from an outer to inner direction. If Flipped is unchecked, then the vectors search
from an inner to outer direction.
3. Go to the Edge Location menu and select an Edge Polarity. If searching for a light
edge against a dark background, choose Dark to Light.

216 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 4. Go to the Target Circle menu and click Learn. If the Edge Location parameters are
set correctly, the system will automatically detect the proper target radius size. The
system uses this radius to compute the center. You may need to adjust the parameters
in the Hough, Target Circle, and Edge Location menus to find the desired feature
accurately. These menus are discussed next.
Hough tab

Search Vector Count

Set the number of search vectors to locate the feature on the container. More vectors
provide a more accurate search, but also take more processing time.
Search Direction
If the box is checked, the search changes to the opposite direction.
Tip: if you flip the search direction, go back to the Target Circle tab and press
Learn to re-learn the target radius size.
Bounding Rectangle
Adjust the size of the area where you would expect the center of the feature to be
found, even with slight movement of parts in the camera‘s field of view. The system
uses only this area to compute the center. If the computed center falls outside of this
bounding area, the registration fails.
Use Height and Width to adjust the number of pixels to create the size of the
rectangle.

 Note: larger sized Bounding Rectangles take more processing time.

Search Resolution
The area (in pixels) within the bounding rectangle where the center should be
computed. A larger resolution allows a larger area. This allows the system to more
accurately locate the center on parts that are not perfectly round.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 217
© 2011 Pressco Technology Inc. Proprietary
 Region Extraction
Choose how the Intellispec should read the information from the region. This usually
depends on the shape of your region. In this inspection, only Read Radially is used.
The data is extracted in a radial direction as shown in the illustration below.

Show Edges
Display the found edges on the image.
Minimum Center Strength
The minimum strength, or quality, you require for the circle fit. When the quality of
the fit is less than this value, the registration fails.
Show Hough Graphics
Display the bounding rectangle and search graphics on the image.
Target Circle tab

 Tip: to quickly set the Target Circle, click the Learn button. You could adjust the
other parameters as necessary.

Target Radius
The size of the feature you want to find. This is automatically computed by using the
Learn process.
Learn button
Using the Edge Location settings, the system automatically sets the Target Radius
size.
Adapting Target Radius
When this is enabled, the system automatically figures out the best fit for the target
radius, within the inner and outer radius of the region.

 Note: Increasing Adaptation Range increases accuracy, but it also increases

inspection time.

Adaptation Range
When Adapting Target Radius is used, this range limits the number of pixels that the
target radius can move in either direction.

218 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Edge Location tab

Edge Polarity
The type of edge for which you want the system to look – Light to Dark, Dark to
Light, or Either. For example, if the feature you want to find is very bright, choose
Dark to Light.
Edge Gradient
The minimum and maximum difference in gray shades, between two pixels, to be
considered an edge.
Edge Delta
The distance between pixels being compared when seeking an edge. A higher Delta
value increases inspection sensitivity because it finds more edges.
Edge Size
Indicates how many pixels in a row to compare (1 to 1, 2 to 2, etc.). The larger the
Edge Size, the stronger the edge will need to be. This parameter acts like a filter that
looks at a length in pixels before and after the edge.
Use Subpixel
Finds edges based on their subpixel location, rather than rounding off to the nearest
pixel. This gives greater centering accuracy.

Radial Edge
Radial Edge registration is good for circular parts that have a distinct edge either on the
inside or outside of the part. This only works with a Ring region. Place the Ring region
where you would expect the edges of the part to fall. The system searches for edges from
the inner to the outer radius (or outer to inner radius), searching for a transition from light
to dark or dark to light pixels. Each search vector tries to detect an edge, using the Edge
Location parameters. Found edges are marked with a cyan or red '+' for pass or fail
status.

To add a Radial Edge registration:

1. Make sure a Ring Region (on page 187) has been added to the inspection tree.
2. Right-click in the inspection tree to see the Inspection menu.
System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 219
© 2011 Pressco Technology Inc. Proprietary
 3. From the Inspection menu, select Add > Registration > Radial Edge. The Radial
Edge registration is added to the inspection tree. Re-name it to something more
meaningful to you.
4. The Radial Edge Menu is displayed and the region is shown on the image. (The
menu is described below) Adjust the placement of the region and parameters as
necessary.
To set up the Radial Edge registration:
1. Make sure the Ring region surrounds the feature that you want to locate. Adjust with
the parameters in the Ring menu (or the Region Editor on the image) if necessary.
2. In the Radial Edge menu select a Search Direction. Flipped means that the vectors
search from an outer to inner direction. If Flipped is unchecked, then the vectors
search from an inner to outer direction.
3. Go to the Edge Location menu and select an Edge Polarity. If searching for a light
edge against a dark background, choose Dark to Light.
4. Go to the Target Circle menu and click Learn. If the Edge parameters are set
correctly, the system will automatically detect the proper target radius size. The
system uses this radius to compute the center. You may need to adjust the parameters
in the Radial Edge, Target Circle, and Edge Location menus to find the desired
feature accurately. These menus are discussed next.
Radial Edge menu

Search Vector Count

Set the number of search vectors to locate the feature on the container. More vectors
provide a more accurate search, but also take more processing time.
Search Direction
If the box is checked, the search changes to the opposite direction.
Radial Tolerance
The number of pixels in either direction of the target circle that the system will
consider an edge (that is, the size range allowed for the part). A radial tolerance of
two allows a four pixel wide area in which the edge of the part may fall.
Show Edges
Display the found edges on the image.
Qualifying Percent Limits
The percentage of edges that must be part of the target circle. If there are not enough
found edges on the target circle, this registration will fail. This can be set lower if
you expect large changes in sample size (less sensitive). It can be set higher if the
size of your product should not vary (more sensitive).

220 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Target Circle menu

Target Radius
The size of the feature you want to find. This is automatically computed by using the
Learn process.
Learn button
Using the Edge Location settings, the system automatically sets the Target Radius
size.
Adapting Target Radius
When this is enabled, the system automatically figures out the best fit for the target
radius, within the inner and outer radius of the region.
Edge Location menu

Edge Polarity
The type of edge for which you want the system to look – Light to Dark, Dark to
Light, or Either. For example, if the feature you want to find is very bright, choose
Dark to Light.
Edge Gradient
The minimum and maximum difference in gray shades, between two pixels, to be
considered an edge.
Edge Delta
The distance between pixels being compared when seeking an edge. A higher Delta
value increases inspection sensitivity because it finds more edges.
Edge Size
Indicates how many pixels in a row to compare (1 to 1, 2 to 2, etc.). The larger the
Edge Size, the stronger the edge will need to be. This parameter acts like a filter that
looks at a length in pixels before and after the edge.
Use Subpixel
Finds edges based on their subpixel location, rather than rounding off to the nearest
pixel. This gives greater centering accuracy.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 221
© 2011 Pressco Technology Inc. Proprietary
 Centerline
Centerline Registration finds the sides of a container and determines the center line
between them. It also computes an orientation of the container. This registration uses the
mirrored polygon ribbon region. With Centerline registration, you can determine the
orientation of a feature and compare it to the orientation of the entire part. You can also
check the slope of the sides of the container, or check the overall shape of the container.

Series IV users: this replaces Midline Orientation, and is similar to Shape Adapt Registration.

 Note: this registration requires a Ribbon Region (on page 190) using settings:
Ribbon Style = Ribbon, and Mirror Ribbon = Enabled.
 Tip: you can use Centerline to determine Registration plus Orientation, or just
Orientation.

To add a Centerline Registration:

1. Place a Ribbon Region (on page 190), using a mirrored ribbon.
2. Right-click in the inspection tree to see the Inspection menu.
3. From the Inspection menu, select Add > Registration > Centerline. The Centerline
registration is added to the inspection tree. Re-name it to something more meaningful
to you.
4. The Centerline Menu is displayed and the region is shown on the image. (The menu
is described below) Adjust the placement of the region and parameters as necessary.
Centerline menu

222 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Applied Results
This determines whether the found center and/or orientation are reported to
inspections that follow the Centerline. Use Center and Orientation to report both to
following inspections. Use Orientation to report only the orientation, but use a
previously found center.
Setup Mode
Use the same parameters to find both sides of the container (Common Setup), or set
up the parameters differently for each side of the container (Individual Setup).
Search Vector Count
Set the number of search vectors to locate the feature on the container. More vectors
provide a more accurate search, but also take more processing time.
Region Extraction
Choose how the Intellispec should read the information from the region. This usually
depends on the shape of your region. In this inspection, only Read Radially is used.
The data is extracted in a radial direction as shown in the illustration below.

DIAGNOSTICS
Show Vectors
Display the search lines on the image.
Show Edges
Display the found edges on the image.
Show Alignment
Display the alignment of the current part with respect to the previous alignment.
SHAPE CHECK
Check the angle of the sides of the container.
Shape Limits
Set the angle limits for the container.
Nominal
The ideal value for the shape of the container.
Shape Sensitivity
Set the sensitivity for the straightness of the center line. 100 indicates that points
must fall on a perfectly straight line (most sensitive). A setting of one indicates that
points can fall anywhere (least sensitive). A value of 90 is good sensitivity in most
cases.
AREA CHECK
Check the area of the points found. It is good for determining underblown and overblown
bottles.
Area Range
The tolerance (in pixels) of the area.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 223
© 2011 Pressco Technology Inc. Proprietary
 Nominal
The expected area size. This number is populated when you press the Learn button.
Learn Nominal Area
Click the Learn button to automatically learn the area.
ANGLE CHECK
Check the orientation of a feature against the previous orientation. If an orientation
inspection was not added to the part program, zero degrees is used. For example, this
could be used to detect turned tabs on a converted end.
Angle Limits
Set the angle tolerance for the feature.
Nominal
The ideal orientation of the feature.
Centerline Sensitivity
Set the orientation sensitivity. The range is from one to 100 with one being the least
sensitive and 100 being the most sensitive. The value of 90 is good sensitivity in
almost all cases.
Search Settings menu

This menu specifies settings for the search vectors.

Vector Direction
Specify which direction the vectors should search, with respect to the center.
Edge Polarity
The type of edge for which you want the system to look – Light to Dark, Dark to
Light, or Either. For example, if the feature you want to find is very bright, choose
Dark to Light.
Edge Gradient
The minimum and maximum difference in gray shades, between two pixels, to be
considered an edge.
Edge Delta
The distance between pixels being compared when seeking an edge. A higher Delta
value increases inspection sensitivity because it finds more edges.
Edge Size
Indicates how many pixels in a row to compare (1 to 1, 2 to 2, etc.). The larger the
Edge Size, the stronger the edge will need to be. This parameter acts like a filter that
looks at a length in pixels before and after the edge.
Use Subpixel
Finds edges based on their subpixel location, rather than rounding off to the nearest
pixel. This gives greater centering accuracy.
224 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Finish Location
Finish Location is used to locate the top corners of a bottle. It uses a ribbon region.
Finish Location also determines part orientation, and passes on the orientation to
subsequent inspections.

Series IV users: Finish Location is similar to Finish Registration in Series IV

To add a Finish Location registration:

1. Make sure a Ribbon Region (on page 190) of Interest has been added to the
inspection tree. An example of region placement is shown below.

2. Right-click in the inspection tree to see the Inspection menu.

3. From the Inspection menu, select Add > Registration > Finish Location. The
registration is added to the inspection tree. Re-name it to something more meaningful
to you.
4. The Finish Location menus are displayed and the region is shown on the image. (The
menus are described below) Adjust the placement of the region and parameters as
necessary.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 225
© 2011 Pressco Technology Inc. Proprietary
 Finish Location tab

Search Vector Count

Set the number of search vectors to locate the feature on the container. More vectors
provide a more accurate search, but also take more processing time.
Search Direction
If the box is checked, the search changes to the opposite direction.
FINISH SETTINGS
Tilt Limits
Set the allowed range of tilt of the part within the image.
Nominal
The expected range of tilt.
Region Extraction
Choose how the Intellispec should read the information from the region. This usually
depends on the shape of your region. In this inspection, only Read Radially is used.
The data is extracted in a radial direction as shown in the illustration below.

Search tab

Edge Polarity
The type of edge for which you want the system to look – Light to Dark, Dark to
Light, or Either. For example, if the feature you want to find is very bright, choose
Dark to Light.
Edge Gradient
The minimum and maximum difference in gray shades, between two pixels, to be
considered an edge.
Edge Delta
The distance between pixels being compared when seeking an edge. A higher Delta
value increases inspection sensitivity because it finds more edges.

226 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Edge Size
Indicates how many pixels in a row to compare (1 to 1, 2 to 2, etc.). The larger the
Edge Size, the stronger the edge will need to be. This parameter acts like a filter that
looks at a length in pixels before and after the edge.
Use Subpixel
Finds edges based on their subpixel location, rather than rounding off to the nearest
pixel. This gives greater centering accuracy.
Corner tab
Adjust these settings to best find the corner on your part.
 Note: Enable the Show Corners option in the Diagnostics tab to see the position of
the vectors.

Corner Desensitization
Larger values are used to detect more rounded corners. This is used to prevent
detection of false corners.
The illustration below shows the top and side vectors that search for the part. Note that
your image may be rotated depending on application. Regardless of orientation, the top
vectors search for the top of your part, and the side vectors search for the sides of your
part.

1 Top vector (perpendicular to the ribbon)

2 Side vector (parallel to the ribbon)

Top Vector: Side Shift

Move the top vectors closer or further away from the corner.
Side Vector: Down Shift
Move the side vectors closer or further away from the corner.
Side Vector: Side Shift
Move the side vectors closer to or further away from the midpoint of the cap or part.
Side Vector: Length
Increase or decrease the length of the side search vectors.
System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 227
© 2011 Pressco Technology Inc. Proprietary
 Diagnostics tab

Show Vectors
Display the search lines on the image.
Show Search Direction
Show the search direction of the vectors with an arrow.
Show Edges
Display the found edges on the image.
Show Corners
Display the location of the finish corners.
Show Corner Search
Display the search used to find the corners. You must also enable 'Show Graphics' in
the Image Options (on page 158) menu.
Show Framing
Display the lines that show where the finish is located based on the projected
corners.

Template Registration
Coming soon.

ORIENTATIONS
An orientation compensates for part rotation by finding a grayscale pattern. An analysis
which must rotate with the part must follow an orientation.
 Note: you must first place a Region of Interest (see "Regions of Interest (ROI)" on
page 186) where you want the Orientation to take place.
Available orientations include Pattern Match (on page 229) and Template Orientation
(on page 231).
 Note: the Centerline (on page 222) and Template Match (see "Template
Registration" on page 228) Registrations also contain an orientation angle that can
be used to orient regions.

228 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Pattern Match
Pattern Match Orientation creates a pattern to be matched. A Pattern Match reference
must be set on one part that you consider to have the desired pattern. The Pattern Match
reference sets the standard to which all other parts inspected must meet. The Pattern
Match is based on percentages; the referenced pattern will be 100%. All other parts will
be compared to the referenced pattern and given a percentage depending on how the two
patterns match up. In other words, a part with an 88% Pattern Match rating is 88%
similar to the referenced part. If the inspected part has too low of a percentage, the part
will fail the orientation.

1 Normal orientation
2 Incorrect orientation

 Note: Pattern Match only works with a Ring Region (on page 187).

To add a Pattern Match Orientation:

1. Make sure a Ring Region (on page 187) of Interest has been added to the inspection
tree. Normally the region is a narrow donut- shaped region placed over a repeatable
pattern on the part, such as ridges or other geometry.
2. Highlight the Ring name in the inspection tree.
3. Right-click in the inspection tree to see the Inspection menu.
4. From the Inspection menu, select Add > Orientation > Pattern Match. The Pattern
Match orientation is added to the inspection tree.
5. The Pattern Match menu is displayed and the region is shown on the image. (The
menu is described below) Adjust the placement of the region and parameters as
necessary.
Pattern Match menu

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 229
© 2011 Pressco Technology Inc. Proprietary
  Important
 Set Reference before adjusting other parameters.

Symmetry Repeat
Divide the donut-shaped region into a number of pie-shaped sections. The system
need only match the gray shade pattern in one of these sections to determine proper
orientation.
An example for the use of symmetry is when you are inspecting the base of a bottle
that has five feet - use a symmetry of five. The system uses a gray shade pattern in
one-fifth of the region, and you are assured proper orientation because these gray
shade patterns are identical in the other four sections of the region.
This feature can speed up this orientation. The time required for the orientation is
reduced by 1/symmetry squared. If you have a symmetry of five, this orientation
takes 1/25th the amount of time it would take with a symmetry of one.
Radial Spacing
The number of pixels between search circles. It can be used to increase the speed of
this inspection, especially if the region is large.
Select Offset Angle
Allows you to easily set the Offset Angle (described below). Click the Select Angle
button, then click in the image where you want the orientation to point to.
Note: you can only set Offset Angle if the inspection is passing. You may have to
adjust other parameters, or disable other inspections while setting this to get the
inspection to pass.
Offset Angle
Allows you to rotate the inspections on an image. Set the angle on a specific feature
to match the current orientation of the part. This feature saves you from modifying
subsequent regions during slight changes that might affect region placement.
Set Reference
Click the Set Reference button to set the reference pattern from
the currently displayed image.
Show Orientation
Display the orientation line on the image.
Part View Display
Allows you to look at different results for the part. You must enable 'Show Pattern
Match' to see the information in the unwrapped image.
Show Correlation Plot - Displays a plot to show the correlation between the
reference pattern and the current image in the unwrapped image.
Show Pattern - Displays the extracted grayscale pattern of the current image.
Show Normalized Pattern - Displays the extracted grayscale pattern of the current
image; the values are normalized so that the highest value is one.
Show Pattern Delta - Displays a plot of the differences in the pattern.

230 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Show Pattern Match
Display a graphical plot of the pattern match on the unwrapped image. An example
is shown below.

Region Extraction
Choose how the Intellispec should read the information from the region. This usually
depends on the shape of your region. In this inspection, only Read Radially is used.
The data is extracted in a radial direction as shown in the illustration below.

Pattern Match Confidence

Define how closely the pattern must match the original sample. To adjust this value,
you can change the numerical value, or click and drag the red line in the Retro-Spec
graph at the top of the screen.
If you check Show Pattern Match, you can see the red failure limit line in the
unwrapped image move when you change this value.

Template Orientation
Not available as of this printing.

ANALYSES
These analyze the part for defects, features, measurements, or gray shades.
 Note: you must first place a Region of Interest (see "Regions of Interest (ROI)" on
page 186) where you want the analysis to take place. We also recommend a
Registration (see "Registrations" on page 211) and an Orientation (see
"Orientations" on page 228) (depending on the part type) prior to an analysis.
The available types of analyses are:
Ambient (on page 232)
Shape Check (on page 234)
Contrast (on page 236)
Measurement (on page 243)
Light Meter (on page 251)
Fill Height (on page 251)
Measure Extract (on page 256)
Distribution (on page 258)
Label Skew Extract (on page 263)
 Note: Your system (and this book) may show only those items that apply to your
application.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 231
© 2011 Pressco Technology Inc. Proprietary
 Ambient
Ambient is a measure of gray levels in a selected region and looks for abnormal gray
levels. There are three ways in which to measure a part‘s ambient: Max Amplitude, Peak
Percentile, and Density. You can set the Ambient Analysis Mode to have maximum
reject limits, minimum reject limits, or a combination of maximum and minimum reject
limits.

1 Normal Ambient
2 Incorrect Ambient

To add an Ambient analysis:

1. Make sure a Region of Interest (see "Regions of Interest (ROI)" on page 186) has
been added to the inspection tree. We also recommend a Registration (see
"Registrations" on page 211).
2. Highlight the region or registration name in the inspection tree.
3. Right-click in the inspection tree to see the Inspection menu.
4. From the Inspection menu, select Add > Analysis > Ambient. The Ambient analysis
is added to the inspection tree.
5. The Ambient menu is displayed and the region is shown on the image. (The menu is
described below) Adjust the placement of the region and parameters as necessary.
Ambient menu

Ambient Technique
This method determines the region‘s ambient. Choose the method through the
drop-down menu.

232 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Max Amplitude looks for the maximum gray level amplitude — the gray level with
the most pixel counts — within the histogram of the search area.

1 Gray level
2 Pixels in the histogram of the image

Peak Percentile locates the gray level value that exceeds the threshold. In the
example below, the system would use the gray level to the right of the line marking
80%.
 Ambient Threshold defines what percentage of the search area to use.

1 Gray level - choose a percentage

2 Pixels in the histogram of the image

Density computes the average of all the pixel gray levels — total gray level divided
by pixels.
Ambient Analysis Mode
Specifies the reject criteria.
Min & Max - The minimum and maximum acceptable ambient gray level values.
Any computed ambient found lower than or greater than these values will cause the
inspection to fail.
Min Only - The minimum acceptable ambient gray level value. Any computed
ambient found lower than this value will cause the inspection to fail.
Max Only - The maximum acceptable ambient gray level value. Any computed
ambient found greater than this value will cause the inspection to fail.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 233
© 2011 Pressco Technology Inc. Proprietary
 Region Extraction
Choose how the Intellispec should read the information from the region. This usually
depends on the shape of your region.
Note: some inspections do not use all of these options
The illustration below shows how the information is read by each method. Note that
these shapes are examples only - your region does not have to match the shape.

1 Read Horizontally - Extract the region horizontally - 90 degrees

with respect to orientation.
2 Read Vertically - Extract the region vertically - parallel with
respect to orientation.
3 Read Circularly - Extract in a circular fashion around the region.
4 Read Radially - Extract region in a radial direction.
5 Read Horizontally and Vertically - Extract the region both
horizontally and vertically (with respect to orientation). This is
used in special cases.

Ambient Limits
The minimum and maximum acceptable ambient gray level values. Any computed
ambient found lower than or greater than these values will cause the inspection to
fail.
Nominal
The expected gray level value of the region of interest.

Shape Check
Shape Check looks for a certain shape in the search region and will reject a part if it is
out of tolerance. This feature helps ensure that the custom search region does not get
fooled by an irregularly shaped container.
 Note: This inspection is only available for Adaptive Regions.

Series IV users: Shape Check is similar to the Shape Adapt region analysis in Series IV.

234 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 The example below shows a normal part [item 1], and a part that failed the Shape Check
[item 2].

1 Normal part
2 Part failed Shape Check

To add a Shape Check inspection:

1. Make sure an Adaptive Region (on page 195) of Interest has been added to the
inspection tree.
2. Highlight the region name in the inspection tree.
3. Right-click in the inspection tree to see the Inspection menu.
4. From the Inspection menu, select Add > Analysis > Shape Check. The analysis is
added to the inspection tree. Re-name the inspection to something more meaningful
to you.
5. The Shape Check menu is displayed and the region is shown on the image. (The
menu is described below) Adjust the placement of the region and parameters as
necessary.

Shape Check tab

Select between three different methodologies to determine proper shape (Area Check,
Cross Section Check, and Vertex Deviation Check).

Area Check
Enable the Area Range portion of the inspection. This computes the area of the
region in pixels to check for proper region size.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 235
© 2011 Pressco Technology Inc. Proprietary
 Area Range
Define the acceptable deviation (in pixels) from the normal area of the region.
Nominal
The normal value of the area.
Learn Nominal Area
Click this button to determine the normal area size.
Cross Section Check
Enable the Cross Section portion of the inspection. This is only used when an
Adaptive region is added to a Centerline registration. The system ensures that the
learned distance between the two sets of points is within tolerance.
Maximum Cross Section Deviation
First use the Learn Cross Section button to determine the normal values. The
distance is in pixels.Then adjust these values per your specifications.
Learn Cross Section
Click this button to determine the normal values for the Cross Section check.
Vertex Deviation Check
Enable the Vertex Deviation Check portion of the inspection. This is only used when
an Adaptive region is added to a Centerline registration. This check looks at the
deviation between consecutive edge points, and is performed on each side. An
example where this feature might be used is when searching for choked necks on
bottles.
The vertex edge points are determined when you use Learn Cross Section.
Maximum Deviation Side 1 and 2
The system computes the distance (in pixels) between consecutive edge points.
Adjust the sensitivity per your specifications.

Contrast
The Contrast analysis looks for light and dark defects within your desired region. You
can set the Contrast analysis to look for light defects only, dark defects only, or both light
and dark defects. In the example image below, a Contrast analysis found a scratch.

To add a Contrast analysis:

1. Make sure a Region of Interest (see "Regions of Interest (ROI)" on page 186) has
been added to the inspection tree. We also recommend a Registration (see
"Registrations" on page 211).
2. Highlight the region or registration name in the inspection tree.
3. Right-click in the inspection tree to see the Inspection menu.

236 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 4. From the Inspection menu, select Add > Analysis > Contrast. The Contrast
inspection is added to the inspection tree. Re-name it to something more meaningful
to you.
5. The Contrast menu is displayed and the region is shown on the image. (The menu is
described below) Adjust the placement of the region and parameters as necessary.
Contrast menu
 Note: The symbol [ ] indicates that this value is in pixels. Your system may show
[mm] for millimeters, ["] for inches, or [ ] blank for custom units. It indicates that
this value can be calibrated using Review Camera Calibration (on page 138) or
Image Analysis (on page 132) for the current sensor.

Contrast Limits
Set the sensitivity of the inspection. You can also move the red and yellow bars on
the Retro-Spec graph by selecting the arrows to the left of the graph.
Size Filter
Choose a defect size you want to catch. For example, you may want to pass very
small defects but fail larger ones. For example, if Size Filter is set to 3 -- 80, any
defects smaller than three pixels or larger than 80 pixels would be ignored.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 237
© 2011 Pressco Technology Inc. Proprietary
 Acceptable Size
This looks at the width of only those peaks that go above the contrast bar. It sums up
the total size of those peaks and puts a limit on how large the total size of the defects
can be. In the Part View graph shown below, there are peaks that go above the
contrast bar. However, Acceptable Size is set to a number greater than the sum of
those peaks, and this part passes. Acceptable Size allows you to pass parts with some
anomalies, but reject parts with too many anomalies.

Use Size Weighting

This feature helps find defects such as wrinkles on metal parts. It is not normally
used on bottles.
 If an area of the part fails, it is weighted. If the area does not fail, it is not
weighted.
 The Acceptable Size parameter changes to provide adjustment for weighting.
 The left value is Acceptable Size; see the description for that parameter.
 The right value adjusts the weighted size limit.
Sizing
Choose between Total Width and Total Area for the inspection. The Number of
Rings also affects Sizing.
 Total Width, the default setting, adds the number of units (pixels, millimeters,
etc.) of defective bars at or above the sensitivity level within an inspection region
or segment.
 Total Area adds all the defect pixels. Suppose your part had two small defects
along the same radial line. Normally, the width of the predominant defect would
be counted. But with Area enabled, all defect pixels are counted. This results in a
larger defect area counted.
Region Extraction
Choose how the Intellispec should read the information from the region. This usually
depends on the shape of your region.
Note: some inspections do not use all of these options
The illustration below shows how the information is read by each method. Note that
these shapes are examples only - your region does not have to match the shape.

238 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 1 Read Horizontally - Extract the region horizontally - 90 degrees
with respect to orientation.
2 Read Vertically - Extract the region vertically - parallel with
respect to orientation.
3 Read Circularly - Extract in a circular fashion around the region.
4 Read Radially - Extract region in a radial direction.
5 Read Horizontally and Vertically - Extract the region both
horizontally and vertically (with respect to orientation). This is
used in special cases.

ADVANCED SETTINGS
Sample Filter
Choose how to filter the samples. The default selection is Integration. Leave that
selected for most applications. Concavity is used for detecting and ignoring draw
marks in two-piece beverage cans.
Fuzzy Edge Removal
This is for parts that have normal anomalies at the edges that are fuzzy, but the
feature edges are sharp and clear on the image. The default is disabled. The higher
the Filter Level, the stronger the fuzzy edge removal. Be aware that this filtering
increases inspection time.
Defect Type
Search for dark, light, or both types of defects.
Optimize settings
Described below.
Detection Mode
Search for either a defect (default setting) or for a feature (for example, a feature that
should be there and its absence represents a defect).
SEGMENT SETTINGS
Number of Rings
The number of concentric rings the region is divided into (for Read Circularly or
Read Radially Region Extractions only). More rings generally means more sensitive.

a Region with one ring

b Region divided into three rings

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 239
© 2011 Pressco Technology Inc. Proprietary
 The example below shows a Part View graph of the same part's region with one ring
[item 1], and that same region divided into several rings [item 2]. Notice that the
width of the peaks do not change, but the amplitude of the peaks change, because the
system is focusing on a smaller region.

1 Part with region with one ring

2 Same part with region divided into several rings

Number of Segments
The number of angular segments the region is divided into.
Ring Height
Ring Height is similar to Number of Rings, but applies to a polygon region. This
number refers to a number of pixels wide or high, depending whether you are using
Read Horizontally or Read Vertically for Region Extraction. Ring Height can
improve inspection sensitivity to defects that do not span the width of the inspection
region. The default value for Ring Height is one, which is the most sensitive value.
In the example below, suppose Ring Height in [item 1] is one pixel, and Ring Height
in [item 2] is five pixels. In this case, the part using Ring Height of one [item 1]
would be more likely to fail than with a Ring Height of five [item 2].

1 Smaller Ring Height - more sensitive

240 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 2 Larger Ring Height - less sensitive

USING THE OPTIMIZE FEATURE

The Optimize feature automatically sets the optimum settings for many inspection
parameters. It is processor-intensive and must be done off-line. For this to work
correctly, ensure that you have moved all acceptable images to the left side of the
Retro-Spec graph (Set A), and the defect images to the right side of the graph (Set B).
Optimize is available under the Advanced Settings.
To use the Optimize feature:
1. Make sure the Retro-Spec graph is in Population view: right-click on the graph to
select Population View.
2. Load a set of good parts into Data Set A using the steps below.
To load Data Set A:
1. Look at the Retro-Spec Population View Graph (on page 179).

2. Click the left arrow button to view the Select Data Sets menu.

3. Click the Image Files button for Set A.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 241
© 2011 Pressco Technology Inc. Proprietary
 4. Click the disk icon to browse to the folder where the images were saved. The
Select Location menu is displayed.

5. Browse to and select the folder that contains the images you want to load.
 To preview the images in the folder, browse through the file names in the
window on the right of the Select Location menu.

6. Click the OK button in the Select Location and Select Data Sets menus to load
all the bitmap images that were previously saved in the selected folder.
Next load a set of images of bad parts into Data Set B. These parts should have defects in
the current inspection's region of interest.
To load images of bad parts:

1. Click the right arrow button to view the Select Data Sets menu.
2. From the Select Data Sets menu, select Latest Defects, or choose Image Files for Set
B. If you choose Image Files, select images similarly as you did for Set A, except
this time choose defect images.
3. Exit the Select Data Sets menu.
If there are any parts that do not belong in either sample set, try moving or deleting those
samples.
 To move an image:
 Click on the image lock icon [item 1] to allow images to be moved.
 Then click and hold the desired image's peak [item 2] - it displays a small
image - and drag it to the other side of the center.
 To delete an image:
 Click on the image lock [item 1] to allow images to be moved.
 Then click on the desired image's peak [item 2] - it displays a small image -
and drag it to the trash can icon [item 3].

242 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
  OR: Click on the desired image's peak [item 2] - and then click the trash can
icon [item 3].
 The system displays a "Deleted!" message above the trash can icon when it
is deleted.

To finish setting up the Optimize feature:

1. In the Contrast menu, choose the Defect Type: light, dark, or both.
2. Adjust the Acceptable Size parameter to catch the size of defect you want to detect.
3. Click the Optimize button. The system will analyze the part sets and determine the
best settings to pass the good parts while failing the bad parts. Wait till the
optimization process is complete - this may take several seconds.
4. Look at the Retro-Spec graph to determine whether the good parts are still passing
and the bad parts are failing. Most likely, you will see a significant separation of
contrast between good and bad parts.
5. Test the inspection by loading more images. You can make slight adjustments in the
Contrast menu if necessary.

Measurement
This analysis measures an inner/outer diameter and/or width of a feature. It can be used
in other types of shapes, but is most often used to measure circular features. It can find
non-round (oval) parts, as well as incorrect widths of circular features.

Series IV users: this inspection is similar to Circle Width Dimension or Retro-Spec Measurement inspection

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 243
© 2011 Pressco Technology Inc. Proprietary
 Before you set up the Measurement analysis:
1. Decide which feature you want to measure: inner diameter, outer diameter, width, or
all three.
2. With calipers or other measuring tools, make actual measurements on a good part.
Measure at least one of the features you want to measure (inner diameter, outer
diameter, and/ or width). Make a note of these measurements to input into the
analysis during setup.
Note: if you choose Inspection Calibration [most common] during setup, then
you only need one measurement. If you choose Feature Calibration, you will
need the actual values of all the features you want to measure.
3. Place a Region of Interest (see "Regions of Interest (ROI)" on page 186) over the
area you want to measure, allowing space to find edges.
Tip: If you want to measure the width of a circular feature, make the region
approximately as wide as the feature on both sides. For example, if the feature is
10 pixels wide, place the region 10 pixels outside of the feature, as well as 10
pixels inside of the feature as in the example shown below.

1 feature
2 region

To add a Measurement analysis:

1. Make sure a Region of Interest (see "Regions of Interest (ROI)" on page 186) has
been added to the inspection tree to surround the areas you want to measure. We also
recommend a Registration (see "Registrations" on page 211) before the
measurement region of interest.
2. Highlight the region or registration name in the inspection tree.
3. Right-click in the inspection tree to see the Inspection menu.
4. From the Inspection menu, select Add > Analysis > Measurement. The Measurement
analysis is added to the inspection tree. Re-name it to something more meaningful to
you.
5. The Measurement menus are displayed and the region is shown on the image. (The
menus are described below) Adjust the placement of the region and parameters as
necessary.
To set up a basic Measurement analysis:
1. In the Measurement menu, pick a Feature Type [see description below].
2. Choose whether to inspect for inner diameter, outer diameter, width, or all three.
Under each of the corresponding tabs, enable those measurements.

244 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Note: for most applications, you can disable Range and Continuity. Leave these
enabled only if required by your plant.
3. Go to the Contrast menu and adjust the Contrast Limits until you find an edge.
4. Go to the Measurement menu and set most of the parameters [described below].
5. Click the Learn button. This sets the inspection limits for the Inner, Outer, and
Width measurements.
6. Find the actual measurements you made on the part prior to setting up the inspection.
Go to the corresponding menus (example, inner diameter = Inner menu). Enter these
values in the Measured Distance field for each measurement (depending on
Calibration Provider setting in the Calibration menu).
 If you use Inspection Calibration [most common] for Calibration Provider, then
you only need to enter one value in one of the Inner/ Outer/ or Width menus.
 If you use Feature Calibration for Calibration Provider, then you must enter
values for all enabled measurements.
 If you use Sensor Calibration for Calibration Provider and the system has
already been calibrated, then skip this step.
7. Change the Units field to match your actual measurement (example, millimeters).
8. Go to the Calibration menu and use the Calibrate on Part [recommended setting]
or Calibrate on Set features to set the scale factor for the analysis.
9. Set other parameters as required by your plant.

Measurement menu
This menu provides settings that will be used in all (Inner, Outer, or Width)
measurements. It also has a Learn feature that automatically sets measurement reject
criteria for you.

Learn Settings
Click to learn the measurements of the part. This sets the diameter, min/max values,
and average values for you and updates that information in the Inner/ Outer/ Width
menus.
Note: if you make significant changes to the parameters in this menu or the other
Measurement menus, click the Learn button again to update the information.
Fuzzy Edge Removal
This is for parts that have normal anomalies at the edges that are fuzzy, but the
feature edges are sharp and clear on the image. The default is disabled. The higher
the Filter Level, the stronger the fuzzy edge removal. Be aware that this filtering
increases inspection time.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 245
© 2011 Pressco Technology Inc. Proprietary
 Feature Type
Determine the type of feature you want the inspection to search for. Use the type that
best finds the region on your part.

1 Light Feature

2 Dark Feature
3 Borders - both dark
4 Borders - both light
5 Borders - dark inner, light outer
6 Borders - light inner, dark outer

Feature Selection Logic

Set this according to your part type and measurement type. Choose the type of edges
you want to find for a type of feature.

 Tip: for most applications, leave Border Sharpness, Balance, Balance Side, and
Allowed Gap Size at their default settings.

Border Sharpness
For most cases, leave this set at 1 - 9. This allows you to choose whether to find
sharp or gradual edges. At the default setting, the system finds both types of edges. If
you only want to find sharp edges, set the values closer to one. If you only want to
find gradual edges, set the values closer to nine.

246 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Balance
For most cases, leave this disabled. This parameter applies mostly to Feature Type =
Feature. If the feature in your image is not the same gray shade across the feature,
you could adjust Balance to compensate for the change in gray shade. Normally, the
histogram across the feature is flat, as in illustration [a]. In the example below, the
histogram for the feature of part [b] shows that the gray scale of the inner diameter is
about 50% of the gray scale of the outer diameter. In this example, we would use a
Balance of 0.5, and we would choose Outer for Balance Side. This allows the system
to treat part [b] as though it has similar gray shades on both sides.

Balance Side
When using Balance, choose which side's contrast needs to be reduced.
Sample Count
Choose how to divide up the circle. For example, if Sample Count is 36, then the
system places a search vector every 10° (360° divided by 36 equals 10°).
Allowed Gap Size
This is used in special cases where you want to ignore a number of segments. Set this
to the number of search vectors you want to ignore. For example, if Sample Count is
36, and the gap is approximately 40°, then the Allowed Gap Size would be four.

a Allowed gap size

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 247
© 2011 Pressco Technology Inc. Proprietary
 Inner/Outer/Width menus
There are three tabs to provide three different measurements. The parameters in each of
the menus are the same.

Inner diameter/outer diameter/width

Check the box under the appropriate tab to perform this measurement.

 Tip: When you click the Learn button in the Measurement menu, the values for
Diameter/Width, Min/Max, and Average are set for you. Normally, you do not need
to adjust these further.

Min/Max
Set the minimum and maximum allowable measurement.
Average
Set the average measurement for the part.

 Tip: for most applications, Range and Continuity are disabled.

Range
Set the acceptable measurement range for the part. This can be used to check for
ovality. The system subtracts the minimum value found from the maximum value
found.
Continuity
This feature checks for local changes in edge position between vectors. This allows
detection of defects where the part may be crushed or bent.

Continuity - Size
Choose the size range of the defects you want to catch, specified in segments.
248 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Units
Choose your preference in the reporting of the measurements. Choose from
millimeters, inches, pixels, and custom. Custom allows any calibration factor to be
used.
Measured Distance
Measure your part with calipers or another tool, then enter the actual value for
Measured Distance. This is used to help calibrate the measurement.

Calibration menu
This menu uses your actual measurements (that you input into the Measured Distance
parameter) to convert the number of pixels into your preferred unit of measurement. This
ensures that the system is making accurate measurements.

Calibration Provider
Specify the source for the display of the calibrated values.
Sensor Calibration -- Calibration can be done through Image Analysis (on page
132), or through an inspection. When Save Calibration is used within an inspection,
that information can be used in any other inspection (that uses Calibration Provider)
for that sensor.
Inspection Calibration -- [most common] use the value from one of your actual
measurements to calibrate the Measurement analysis. Additional Dimension and
Units parameters are available to choose one of your measurements and preferred
unit of measurement. Additionally, Conversion Factor can be adjusted manually to
get the best match between pixels and physical length.
Feature Calibration -- use separate calibration settings for each of the enabled
measurements (inner diameter, outer diameter, or width). You must enter an actual
measured value into each of the appropriate menus.
Dimension
[Available when Calibration Provider = Inspection Calibration] Specify which
dimension to use to calibrate the inspection.
Units
Choose your preference in the reporting of the measurements. Choose from
millimeters, inches, pixels, and custom. Custom allows any calibration factor to be
used.
Calibrate on Part
Use the current image to calibrate the Measurement analysis. Use a known good part.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 249
© 2011 Pressco Technology Inc. Proprietary
 Calibrate on Set A
Use the current set of images in Set A to calibrate the Measurement analysis. The
system takes the average value of the set and uses that number to calibrate the
analysis.
Learn Calibration
Click the Save Calibration button to automatically determine the scale factor, which
converts the value to the desired units.
Conversion Factor
This indicates the pixel size and is used to convert one pixel into the units selected.
Contrast menu
This menu allows you to adjust for sensitivity and defect size for the inspection.

Contrast Limits
Set the sensitivity of the inspection. You can also move the red and yellow bars on
the Retro-Spec graph by selecting the arrows to the left of the graph.
Size Filter
Choose a feature size you want to measure. For example, you may want to ignore
very small features but find larger ones. For example, if Size Filter is set to 3 -- 80,
any feature smaller than three pixels or larger than 80 pixels would be ignored.
Results window
The results displayed for a measurement inspection are different than other inspections.
In addition to the parameters, a measurements table is displayed.

You can perform several functions through this results window, including:

250 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Go directly to the parameters to adjust a particular measurement. If you click the
[6.01] in the example, the Width menu is displayed and the Min/ Max parameter is
highlighted for you.
View the corresponding Retro-Spec graph. If you click [6.01] under Width in the
example, the Width Min/ Max graph is displayed at the top of the screen.
More options are available when you right-click over this window to see the
Measurement Results menu. This menu allows you to enable or disable an entire
measurement set such as Inner, Outer, or Width. If you click "Enable/ Disable Measure,"
then the parameter you right-clicked to see this menu becomes enabled or disabled.

Light Meter
Light Meter is not available as of this publication.

Fill Height
Fill Height inspection is used for determining the fill level of containers, mainly to find
containers with high fill or low fill. The Fill Height inspection compares the fill level of
the liquid to a standard reference point, which is typically the neck ring of a container.
 Notes: This inspection requires a Measure ROI (on page 193) Region using two
regions.
The example below shows a bottle with a normal fill height [item 1], and a bottle with a
fill height that is too low [item 2].

1 Normal fill height

2 Fill height too low

To add a Fill Height inspection:

1. Make sure a Measure ROI (on page 193) Region of Interest has been added to the
inspection tree. Suggested settings are as follows:
1) In the Measure ROI menu, set Region Count to Two Regions.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 251
© 2011 Pressco Technology Inc. Proprietary
 2) Place Region One over a distinct reference point, such as the neck ring.
3) Place Region Two over a section of the bottle where you expect to see the liquid
level. An example is shown below.
4) Save and close the Measure ROI region menu.

2. Highlight the region name in the inspection tree.

3. Right-click in the inspection tree to see the Inspection menu.
4. From the Inspection menu, select Add > Analysis > Fill Height. The analysis is
added to the inspection tree. Re-name the inspection to something more meaningful
to you.
5. The Fill Height menus are displayed and the regions are shown on the image. (The
menus are described below) Adjust the placement of the regions and parameters as
necessary.

Fill Height tab

 Note: The symbol [ ] indicates that this value is in pixels. Your system may show
[mm] for millimeters, ["] for inches, or [ ] blank for custom units. It indicates that
this value can be calibrated using Review Camera Calibration (on page 138) or
Image Analysis (on page 132) for the current sensor.

Fill Mode
Choose whether to measure fill level at the Top Only or at the Top and Bottom
Top Only is generally used for water or other non-carbonated beverages.
Top and Bottom is used mainly for carbonated beverages, or beverages that foam
when the liquid sloshes around in the container as it moves in front of the inspection
module. The inspection can measure the distance from the reference point to the top
of the foam, and also the from the reference point to the bottom of the foam.

252 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Part Orientation
Choose the orientation of your part. In many cases, the part image is sideways to
optimize the inspection area on the screen.
Reference Region
Choose a region from the Measure ROI region of interest to set as the reference point
(in our setup example, we picked Region 1). A typical setup uses the neck ring of a
bottle as the reference region. The direction of the search is determined in the region
setup (search towards the diamond). You can change search direction by
right-clicking over the image and using the choices from the Image Options (on page
158) menu.

Correct Fill Position

Enables edge correction, where the system uses a "moving average" technique to
eliminate outlying edges (example: edges caused by water spots or bubbles in the
liquid).
Fill Correction Deviation
[Available when Correct Fill Position is enabled] This is used to correct stray points
that fall too far away from the moving average edge position. The value is in pixels.
Make sure you use a high enough value, or the inspection will not properly detect
sloshing liquid. A common value to use is 25 or higher.
Fill Height Limits
Define the valid fill height range per your specifications.
Nominal
The ideal fill height value.
Show Fill Height
Display the fill height measurement.
Reference tab

Set the parameters to find the edges in the reference region.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 253
© 2011 Pressco Technology Inc. Proprietary
 Vector Spacing
The distance between search vectors.
Max Missed Edges
The number of search vectors that are allowed to fail without causing the inspection
to fail.
Edge Polarity
The type of edge for which you want the system to look – Light to Dark, Dark to
Light, or Either. For example, if the feature you want to find is very bright, choose
Dark to Light.
Edge Gradient
The minimum and maximum difference in gray shades, between two pixels, to be
considered an edge.
Edge Size
Indicates how many pixels in a row to compare (1 to 1, 2 to 2, etc.). The larger the
Edge Size, the stronger the edge will need to be. This parameter acts like a filter that
looks at a length in pixels before and after the edge.
Edge Thickness
The number of consecutive times that the gradient must be met to define an edge.
Edge Delta
The distance between pixels being compared when seeking an edge. A higher Delta
value increases inspection sensitivity because it finds more edges.
Show Edges
Display the found edges on the image.
Show Vectors
Display the search lines on the image.
Show Search Direction
Show the search direction of the vectors with an arrow.
Fill Top or Fill Bottom tab

Set the parameters to find the edges for the fill level top (Fill Top menu) or the fill level
bottom (Fill Bottom menu).
Vector Spacing
The distance between search vectors.

254 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Search Direction
If the box is checked, the search changes to the opposite direction.
Max Missed Edges
The number of search vectors that are allowed to fail without causing the inspection
to fail.
Edge Polarity
The type of edge for which you want the system to look – Light to Dark, Dark to
Light, or Either. For example, if the feature you want to find is very bright, choose
Dark to Light.
Edge Gradient
The minimum and maximum difference in gray shades, between two pixels, to be
considered an edge.
Edge Size
Indicates how many pixels in a row to compare (1 to 1, 2 to 2, etc.). The larger the
Edge Size, the stronger the edge will need to be. This parameter acts like a filter that
looks at a length in pixels before and after the edge.
Edge Thickness
The number of consecutive times that the gradient must be met to define an edge.
Edge Delta
The distance between pixels being compared when seeking an edge. A higher Delta
value increases inspection sensitivity because it finds more edges.
Show Edges
Display the found edges on the image.
Show Vectors
Display the search lines on the image.
Show Search Direction
Show the search direction of the vectors with an arrow.
Calibration tab

Set the parameters to convert pixel measurement into your preferred measurement unit.
Calibration Mode
The system will convert the pixel dimensions into your preferred unit of
measurement.
Sensor Calibration -- Use the calibration previously set up for the sensor through
Image Analysis (on page 132) or through another inspection.
Inspection Calibration -- Use the calibration from this inspection only.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 255
© 2011 Pressco Technology Inc. Proprietary
 Units
Choose your preference in the reporting of the measurements. Choose from
millimeters, inches, pixels, and custom. Custom allows any calibration factor to be
used.
Conversion Factor
This indicates the pixel size and is used to convert one pixel into the units selected.
Learn Calibration
Click the Save Calibration button to automatically determine the scale factor, which
converts the value to the desired units.
Save Calibration
Click this button to save the calibration scale and units to the sensor for use by other
inspections.
Measured Distance
Measure your part with calipers or another tool, then enter the actual value for
Measured Distance. This is used to help calibrate the measurement.
Measured Fill Level
Measure your part's normal fill level (with respect to the bottom of the bottle) with
calipers or another tool, then enter the actual value for Measured Fill Level. This is
used to help calibrate the measurement.

Measure Extract
This analysis will use edge search criteria to find the minimum, maximum, and average
edge location in a Measurement ROI. You then add a Dimension - Distance (on page
266) inspection to do the measurement of the found feature position.

To add a Measure Extract analysis:

1. Make sure a Measure ROI (on page 193) Region of Interest has been added to the
inspection tree. Make sure the region is placed over the feature(s) you want to
measure.
2. Highlight the Measure ROI region name in the inspection tree.
3. Right-click in the inspection tree to see the Inspection menu.
4. From the Inspection menu, select Add > Analysis > Measure Extract. The Measure
Extract analysis is added to the inspection tree. Re-name it to something more
meaningful to you.
5. The Measure Extract menu is displayed and the region is shown on the image. (The
menu is described below) Adjust the placement of the region and parameters as
necessary.

256 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Measure Extract menu

Vector Spacing
The distance between search vectors.
Max Missed Edges
The number of search vectors that are allowed to fail without causing the inspection
to fail.
Edge Polarity
The type of edge for which you want the system to look – Light to Dark, Dark to
Light, or Either. For example, if the feature you want to find is very bright, choose
Dark to Light.
Edge Gradient
The minimum and maximum difference in gray shades, between two pixels, to be
considered an edge.
Edge Size
Indicates how many pixels in a row to compare (1 to 1, 2 to 2, etc.). The larger the
Edge Size, the stronger the edge will need to be. This parameter acts like a filter that
looks at a length in pixels before and after the edge.
Edge Delta
The distance between pixels being compared when seeking an edge. A higher Delta
value increases inspection sensitivity because it finds more edges.
Enhance Vectors
Computes an average pixel value from a neighborhood of 3x3 pixels around each
pixel of the vector.
Show Edges
Display the found edges on the image.
Show Vectors
Display the search lines on the image.
Show Search Direction
Show the search direction of the vectors with an arrow.
Show Measurement Positions
Show the location of the measurement positions (minimum, maximum, and average).

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 257
© 2011 Pressco Technology Inc. Proprietary
 Distribution
The Distribution inspection looks at color printing on parts, detecting 'tramp cans' or
gross decoration errors on parts. If you are familiar with the Pressco Extractor product,
the Distribution inspection will seem familiar to you.
This inspection can also inspect for proper color of a product. For example, if you are
inspecting blue preforms, it can detect when a preform is not the proper color blue, or if
it is an incorrect color.
The Distribution inspection can inspect for gross decorator defects in gray scale images
or color images. Use Gray Scale mode if your system does not have a color camera, or
you want to focus on a specific range of gray shades. This can help detect scratches or
other defects where the color is missing from an area on the part.

The inspection uses:

A learned data set to compare to newly inspected parts
Color histograms (see "Distribution Histogram Types" on page 262) that consist of
a number of color bins. Each color in the region of interest is analyzed. The total
number of pixels containing a certain color (or gray scale) are counted and placed in
each bin.
To add a Distribution analysis:
1. Make sure a Region of Interest has been added to the inspection tree.
2. Highlight the region name in the inspection tree.
3. Right-click in the inspection tree to see the Inspection menu.
4. From the Inspection menu, select Add > Analysis > Distribution. The analysis is
added to the inspection tree. Re-name the inspection to something more meaningful
to you.
5. The Distribution menu is displayed and the region is shown on the image. (The menu
is described below) Adjust the placement of the region and parameters as necessary.
LOAD A SET OF GOOD IMAGES INTO DATA SET A
You can use images of the last parts run (up to 100 parts) and learn using this data.
However, you must make sure that all the images in the data set are from good parts. You
can look at the Population View graph and delete the images you do not want.
Alternately, you can load a set of known good images that you have saved previously
using the steps below.
To load Data Set A:
1. Look at the Retro-Spec Population View Graph (on page 179).

258 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 2. Click the left arrow button to view the Select Data Sets menu.

3. Click the Image Files button for Set A.

4. Click the disk icon to browse to the folder where the images were saved. The
Select Location menu is displayed.

5. Browse to and select the folder that contains the images you want to load.
 To preview the images in the folder, browse through the file names in the
window on the right of the Select Location menu.

6. Click the OK button in the Select Location and Select Data Sets menus to load
all the bitmap images that were previously saved in the selected folder.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 259
© 2011 Pressco Technology Inc. Proprietary
 SET UP THE DISTRIBUTION INSPECTION
To set up a Distribution inspection:
1. Make sure a good set of images is loaded into Data Set A.
2. Choose a different Histogram Type if appropriate for your part.
3. Use the Learn function.
4. Set the Attenuation if desired.
5. Use the Learn More function if desired.
 Note: To use the Learn More function, you will need a set of part images in Data Set
A. The images can be the last 100 parts you have inspected, or images from a file. To
load more images, use the instructions to "Load a set of good images into Data Set
A" listed above.

Distribution tab

Histogram Type
Select one of the Distribution Histogram Types (on page 262). This is not used if
Color Mode = Gray Scale.
Gray Scale
Specify the range of gray scales for the distribution inspection. This is not used if
Color Mode = RGB.
Bin Count
This is only used when Color Mode = Gray Scale. Set the number of bins (gray
shades) the histogram is divided into. Note that some constraints may apply, and this
number may not exactly match the number of bins.
Deviation Limits
Set the tolerance level for the colors or gray scale values. Positive values represent
too much of some color. Negative values represent too little of some color. The
values correspond to the largest deviations of some color from its expected amount,
which is determined when learning the data set. Values of zero represent no
deviation of color.
Attenuation
Set the minimum number of pixels of a color or gray shade that must be seen before
they are counted. For example, if Attenuation is set at 100, there must be at least 100
pixels of that color or gray shade, or it will be ignored. Increasing attenuation
reduces sensitivity to small changes. It ensures that only significant color changes
cause the product to fail.

260 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Learn
The Distribution inspection needs to learn the colors or gray shades of your product.
To learn, the inspection looks at the samples in Data Set A. Therefore, you will need
a set of images in Data Set A. The data set should contain a good sample of your
production line. Ideally, you should store the images of about 100 good parts in Data
Set A. The larger the sample population, the better the inspection results.
Note: if there are any defective parts in Data Set A, they will be included in the
learned data. Therefore, you might want to look through the data set using the
Comparison View graph, and move defective parts to Data Set B.
Note: Learn overwrites existing data. It can be used if you are testing the
inspection on a new part, or want to clear the data from a previous learn.
Learn More
[only available after you use Learn] - After you have used the Learn function, you
can add to the learned data. Use this to learn new parts where the colors might be
slightly different than your original data set, but are still good parts. This builds a
wider tolerance of colors for your parts. This feature can be used at any time - for
example: immediately after the initial learn, or several weeks later.
Note: We recommend that after running the Learn function on 100 parts, you use
the Learn More button several times to get a good sample population.
Region Extraction
Choose how the Intellispec should read the information from the region. This usually
depends on the shape of your region.
Note: some inspections do not use all of these options
The illustration below shows how the information is read by each method. Note that
these shapes are examples only - your region does not have to match the shape.

1 Read Horizontally - Extract the region horizontally - 90 degrees

with respect to orientation.
2 Read Vertically - Extract the region vertically - parallel with
respect to orientation.
3 Read Circularly - Extract in a circular fashion around the region.
4 Read Radially - Extract region in a radial direction.
5 Read Horizontally and Vertically - Extract the region both
horizontally and vertically (with respect to orientation). This is
used in special cases.

Color Mode
Choose whether to extract the data in Gray Scale or RGB mode. Note that your
system must have a color camera to use RGB mode.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 261
© 2011 Pressco Technology Inc. Proprietary
 INFORMATION ABOUT THE GRAPHS IN DISTRIBUTION INSPECTION
The Part View graph view shows the distribution of the color of pixels in the inspection's
region of interest. Each bar on the graph represents a number of pixels in each color bin.
The color bins are shown in the color band at the bottom of the graph. For information
about the color bins, refer to Distribution Histogram Types (on page 262).
The example below shows a Part View graph with a good part (top) and a defective part
(bottom). The defective part had too many pixels of several different colors in this
example - possibly a 'tramp' part.

Distribution Histogram Types

In the Distribution (on page 258) inspection, there are several color histograms available.
Most often, you will be using the New Retro-Spec Color Histogram. You will notice the
difference between the histograms in the color bar directly below the Retro-Spec Part
View Graph (on page 182).

1 New Retro-Spec Color Histogram

2 Special Color Histogram (Chartreuse, Green, Spring Green shown)
3 Classic Extractor Histogram
4 White Level Histogram - not shown

To see a different histogram:

1. Select a different from the Histogram Type drop-down menu.
262 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 2. Switch to Population View on the graph by right-clicking the Retro-Spec graph, then
selecting Population View from the Retro-Spec Options menu.
3. Switch to Part view by right-clicking on the Retro-Spec graph, then selecting Part
View from the Retro-Spec Options menu. The new histogram is displayed below the
graph.
NEW RETRO-SPEC COLOR HISTOGRAM
In this histogram, there are 16 bins of gray scale, 48 bins of dark or pastel colors, and 192
bins of very bright colors. The 48 bins of dark or pastel colors have a wider tolerance,
and therefore you may see most of the colors of your part in those bins. This histogram
also has some overlapping of colors - that is, pixels may be mapped to more than one
color bin. This ensures that slight variations of color do not cause the product to fail.
SPECIAL COLOR HISTOGRAMS
In special cases, you may use other color histograms.The color bars are viewable under
the Part View graph.
If you are trying to detect off-color parts, such as preforms, use one of the special color
histograms. For example, If your preforms are supposed to be green, use the histogram
that most closely matches the correct color. This provides a large range of green colors to
be detected. When a different color part (blue, for example) goes through your product
stream, that part will be easily detected because it will not fall into the learned green
color range.
CLASSIC EXTRACTOR HISTOGRAM
This histogram is the same as the original Pressco Extractor product. It has 16 gray scale
bins and 240 color bins. This is different from the New Retro-Spec Color Histogram in
that it does not have the middle section of 48 bins of dark or pastel color.
This histogram is only used when an approximate comparison between the original
Extractor product and the Retro-Spec Distribution is required.
WHITE LEVEL HISTOGRAM
(As of this printing, the white level histogram is not displayed under the Retro-Spec
graph)
This histogram is used for pastel colors, or if you want to differentiate between shades of
the same color. For example, you might need to detect when a yellow color is too light
compared to the normal yellow shade.

Label Skew Extract

Label Skew Extract is similar to Measure Extract (on page 256). Label Skew Extract is
specialized to locate the edge of the label and can be set up for either one or two search
regions. It finds the edges of a label and draws a "best fit" line using those edges. The
inspection's main function is to export this data to a Dimension > Angle inspection.
Label Skew Extract inspection can reject a part if the label is not consistent enough, such
as a flagged label.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 263
© 2011 Pressco Technology Inc. Proprietary
 Label Skew requires a Measure ROI (on page 193) to set up the region(s). The actual
skew inspection is handled by the Angle (on page 270) dimension.

1 Normal label
2 Skewed label

To add a Label Skew Extract inspection:

1. Make sure a Measure ROI (on page 193) Region of Interest has been added to the
inspection tree. Set up the Measure ROI for one or two regions.
2. Highlight the region name in the inspection tree.
3. Right-click in the inspection tree to see the Inspection menu.
4. From the Inspection menu, select Add > Analysis > Label Skew Extract. The
analysis is added to the inspection tree. Re-name the inspection to something more
meaningful to you.
5. The Label Extract and Region menus are displayed and the region is shown on the
image. (The menus are described below) Adjust the placement of the region and
parameters as necessary.
6. After setting up the Label Skew extract, add an Angle (on page 270) dimension.

Label Skew Extract tab

Check Consistency
Enable the consistency check (the label skew check).
Label Consistency
Set up the limits for the position of the found edges. This number indicates the
straightness of a line. A lower number means the points do not deviate much from a
straight line and is therefore more consistent.

264 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Region 1 tab
Set the parameters so that desired label edges are found. Note that search direction and
region position can be set by using the Image Options (on page 158) menu. Right-click
over the image to see the Image Options menu.

Vector Spacing
The distance between search vectors.
Max Missed Edges
The number of search vectors that are allowed to fail without causing the inspection
to fail.
Edge Polarity
The type of edge for which you want the system to look – Light to Dark, Dark to
Light, or Either. For example, if the feature you want to find is very bright, choose
Dark to Light.
Edge Gradient
The minimum and maximum difference in gray shades, between two pixels, to be
considered an edge.
Edge Size
Indicates how many pixels in a row to compare (1 to 1, 2 to 2, etc.). The larger the
Edge Size, the stronger the edge will need to be. This parameter acts like a filter that
looks at a length in pixels before and after the edge.
Edge Delta
The distance between pixels being compared when seeking an edge. A higher Delta
value increases inspection sensitivity because it finds more edges.
Edge Thickness
The number of consecutive times that the gradient must be met to define an edge.
Use Subpixel
Finds edges based on their subpixel location, rather than rounding off to the nearest
pixel. This gives greater centering accuracy.
System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 265
© 2011 Pressco Technology Inc. Proprietary
 Enhance Vectors
Computes an average pixel value from a neighborhood of 3x3 pixels around each
pixel of the vector.
Show Vectors
Display the search lines on the image.
Show Search Direction
Show the search direction of the vectors with an arrow.

DIMENSIONS
The dimension inspection type is special in that it connects the results of two other
inspections to do the analysis. For example, a distance inspection can connect two
registrations to measure the distance between centers of two features.
The Dimension inspections include:
Distance (on page 266)
Angle (on page 270)
 Note: Your system (and this book) may show only those items that apply to your
application.

Distance
The Distance inspection computes the distance between two points. This is useful if you
want to find features that are out of tolerance or out of place on a part. Distance
inspection does NOT use a region. It obtains information produced in other inspections.
The other inspections can include a Registration (it uses the found registration point), or
a Measure Extract inspection.

Series IV users: this inspection produces the same results of Dimension inspection, but in Series V the
measurement points are found by other inspections.

Examples of where Distance inspection might be used is for detecting swung gates or
high caps on bottles, turned tabs on converted or EZO ends, or computing finish
dimensions. The example below shows a gate position computed with respect to the
center of the base.

1 Full image with swung gate

2 Enlarged image of good part
3 Enlarged image of bad part showing incorrect position of gate

266 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Distance can be computed with respect to the center of the screen, if desired.

To add a Distance measurement:

1. Make sure at least one Registration (see "Registrations" on page 211) or Measure
Extract (on page 256) inspection is placed in the inspection tree. To find the distance
between two points, place the registrations or Measure Extract inspections for each
point.
2. Right-click in the inspection tree to see the Inspection menu.
3. From the Inspection menu, select Add > Dimension > Distance. The dimension is
added to the inspection tree. Re-name it to something more meaningful to you.
4. The Distance menus are displayed and the region is shown on the image. (The menus
are described below) Adjust the parameters as necessary.
To set up a basic Distance measurement:
1. Choose a Distance Component from the Distance tab.
2. Go to the Extraction 1 tab and click the Select Inspection button.
3. Select the first reference point (in the inspection tree) you want to use for the
Distance measurement. Click the Select Inspection button again to complete the
selection.
4. Go to the Extraction 2 tab and click the Select Inspection button.
5. Select the second reference point (in the inspection tree) you want to use for the
Distance measurement. Click the Select Inspection button again to complete the
selection.
6. Go back to the Distance tab and set the Distance Limits.
7. Adjust other parameters as necessary.
Distance menu
 Note: The symbol [ ] indicates that this value is in pixels. Your system may show
[mm] for millimeters, ["] for inches, or [ ] blank for custom units. It indicates that
this value can be calibrated using Review Camera Calibration (on page 138) or
Image Analysis (on page 132) for the current sensor.

Distance Component
Point to Point -- [most common] Find the distance between two reference points.
Perpendicular to Orientation and Parallel to Orientation -- These two modes are
good for measuring distance across a bottle finish. You would set this mode
depending on the part orientation.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 267
© 2011 Pressco Technology Inc. Proprietary
 1 Part oriented upright - use Perpendicular to Orientation
2 Part oriented sideways - use Parallel to Orientation

Note: If you use Finish Location or Centerline registrations for either of the
extractions, note that these registrations produce an orientation. The distance
measured will reference the orientation produced by the Finish Location or
Centerline registrations. If using other inspections, zero degrees or ninety
degrees is used as a reference.
Setup
Set up the reject criteria for the measurement.
Distance Limits
Specify the minimum and maximum distance between the two reference points.
Nominal
The ideal distance.
Extraction 1 and Extraction 2 menus
 Note: when only one inspection is used for Extraction, the second reference point
used is the center of the screen.

Select Extraction
These menus allow you to choose an inspection to use as a reference point for the
measurement. Click the Select Inspection button, then choose an inspection from the
inspection tree. Click the Select Inspection button again to set the choice. The
Assigned Inspection and Location Provider Type information is filled in -- you
cannot manually change these.
In this example, we chose Hough as Extraction 1 and Feature as Extraction 2 from
the inspection tree. Those inspections become highlighted when Distance is selected
in the inspection tree and/or is being edited.

268 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Reference Point
(Available when you use the Measure Extract inspection) Choose which edges to use
when computing Distance.

Minimum Position -- The system will use the minimum distance of the search
region, and reject parts if the measurement is out of limits.
Maximum Position -- The system will report the maximum distance of the search
region, and reject parts if the measurement is out of limits.
Average Position -- The system will report the average distance of the search region,
and reject parts if the measurement is out of limits.
Suppose the illustration below indicates a search region, in which the system is
searching from right to left, seeking a light to dark transition. Position 1 is the
Maximum Position. Position 2 is the Average Position. Position 3 is the Minimum
Position found in the search region.

Finish Corner
(Available when you use Finish Location as the extraction for Distance) Choose
which corner to use as a reference when computing Distance.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 269
© 2011 Pressco Technology Inc. Proprietary
 Calibration menu
Calibration allows you to program the system to translate pixels into your desired units
of measure (mm, for example).

Calibration Mode
The system will convert the pixel dimensions into your preferred unit of
measurement.
Sensor Calibration -- Use the calibration previously set up for the sensor through
Image Analysis (on page 132) or through another inspection.
Inspection Calibration -- Use the calibration from this inspection only.
Units
Choose the unit of measure you used to measure your part. Choose from millimeters,
inches, pixels, or custom. Custom allows any measurement values.
Conversion Factor
This indicates the pixel size and is used to convert one pixel into the units selected.
The initial conversion will be controlled by the Learn Calibration results. You can
adjust this value manually if necessary.
Learn Calibration
Click to learn the Conversion Factor.
Note: you must first enter the Measured Distance before learning calibration.
Save Calibration
Click to save the calibration scale and units to the sensor for use by other inspections.
Measured Distance
Using a Golden Part or good sample part, measure the distance where the Distance
inspection will measure your part. Enter the measured value for this parameter. The
system will compare your measured distance to future parts inspected.

270 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Angle
Angle computes the difference in angles between two orientations or registrations. Angle
does NOT use a region by itself. It uses information obtained in previous registrations or
orientations. To measure an angle, use at least one registration or orientation - anything
that produces an orientation. Examples where Angle could be used are to find skewed
labels, or turned tabs on converted ends or EZO ends.
Inspections that produce an orientation, that can be used to compute an angle include:
Centerline (on page 222)
Finish Location (on page 225)
Template Registration (on page 228)
Pattern Match (on page 229)
Template Orientation (on page 231)
Label Skew Extract (on page 263)
In the example below, a label angle is computed with respect to the centerline of the part.

1 Good part
2 Bad part - label angle is out of tolerance

You can measure the angle with respect to zero degrees on the image, if desired.

To add an Angle dimension:

1. Make sure at least one inspection that produces an orientation has been added to the
inspection tree. [see list above]
2. Right-click in the inspection tree to see the Inspection menu.
3. From the Inspection menu, select Add > Dimension > Angle. The Angle dimension
is added to the inspection tree. Re-name the inspection to something more
meaningful to you.
4. The Angle menu (along with two Orientation tabs) is displayed and the region is
shown on the image. (The menu is described below) Adjust the placement of the
region and parameters as necessary.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 271
© 2011 Pressco Technology Inc. Proprietary
 To set up Angle dimension:
1. Select the Orientation 1 tab.
2. Click the Select Inspection button.
3. From the inspection tree on the left side of the screen, choose an inspection to
reference one angle. The inspection you choose must be one that produces an
orientation. See list at the beginning of this topic.
4. Click the Select Inspection button again to complete the selection.
5. If you have another inspection to reference, use the Select Inspection button in the
Orientation 2 tab. If you do not have another inspection to reference, the system uses
zero degrees on the image as a reference.
6. Go to the Angle tab and set the Angle Limits to pass or fail parts based on your
quality control criteria. For example, a part may be rejected if the angle of the label is
too large compared to the centerline of a bottle.
7. Adjust other parameters as necessary to pass or fail parts per your criteria.

Angle tab

Angle Limits
Set the valid range of measured angles per your specifications.
Nominal
The ideal angle measured.
Angle Mode
Use the Smallest or Largest Angle. An example: the system could measure an angle
at 2° or 358° depending which direction it is measuring. Choose whether to use the
smallest or largest angle found.
Flip Angle 180
Use this option if your angles are pointing in opposite directions and you want them
aligned in the same direction. Sometimes this depends on how a ribbon was drawn,
for example.
Orientation tab (1 or 2)
Pick the reference point(s) to measure the angle.
 Note: when only one inspection is used for Extraction, the reference angle used is
zero degrees, so the inspection would measure the angle with respect to zero
degrees.

272 Inspections System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Select Extraction
These menus allow you to choose an inspection to use as a reference point for the
measurement. Click the Select Inspection button, then choose an inspection from the
inspection tree. Click the Select Inspection button again to set the choice. The
Assigned Inspection and Location Provider Type information is filled in -- you
cannot manually change these.
In this example, we chose Finish Location as Extraction 1 and Centerline as
Extraction 2 from the inspection tree. Those inspections become highlighted when
Angle is selected in the inspection tree and/or is being edited.

Angle Selection
This parameter is available when the inspection selected for the extraction contains
more than one data point to reference. Examples include Finish Location or
Centerline. Select the data point to which you want to reference the angle.

CORRELATION
There are no correlation inspections in the system yet.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Inspections 273
© 2011 Pressco Technology Inc. Proprietary
Chapter 14
SYSTEM HARDWARE INFORMATION
This section shows wiring diagrams and pinouts, and lists signals of various Intellispec
system components.
Related sections include:
Cluster Box
Inspection Module Adjustments (see "Inspection Module Adjustments and Wiring
Diagrams" on page 287)
Extended I/O (on page 321)
Maintenance Frequency - BNS
Maintenance Frequency (on page 331)
 Note: some sections are only included in books pertaining to specific applications.
This book may not contain all of the above sections.

POWER UP
Intellispec Series V systems have multiple power switches. Make sure the power
switches are turned on for the user interface, each camera module, and cluster box (if
applicable). See the illustrations below for power switch locations.
The power connections for the user interface are found on the right side of the cabinet.

1 2

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) System Hardware Information 275
© 2011 Pressco Technology Inc. Proprietary
 1 PC (computer) power connector
2 Monitor power connector
3 User interface power switch
Each integrated camera module (for example the CPV series of inspection tunnels) has
its own power on/off switch.

In system configurations that have a cluster box:

if the cluster box has a UPS, open the cluster box door and switch on the UPS, then
turn the external on/off switch to power all camera modules connected to the cluster
box.

POWER DOWN
To completely power down all components of the Intellispec, make sure the following
power switches are turned off:
User interface
Integrated inspection modules (if applicable)
Cluster box (if applicable)
UPS inside the Cluster box (if applicable). Open the Cluster box door to switch off
the UPS.
The user interface, inspection modules, and cluster box are all independent of each other.
Therefore, if you need to service any of the above modules, any one can be turned off by
itself.

Important
If you re-start the computer, turn off the User Interface power and leave it off for
about 40 seconds before turning it back on. This allows the electronic
components to correctly reset.

276 System Hardware Information System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 To see the locations of the power switches, refer to Powering on the system (see "Power
Up" on page 275).

SERVICING THE USER INTERFACE

Warning
Potential hazardous voltage from the UPS. Use caution when servicing.

WIRING DIAGRAMS
Pressco PC outlet wiring

Warning
The Pressco PC outlet is only to be used to provide power to the Intellispec PC.
Any other use is prohibited.
The power connections for the user interface are found on the right side of the cabinet.

1 2

1 PC (computer) power connector

2 Monitor power connector
3 User interface power switch

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) System Hardware Information 277
© 2011 Pressco Technology Inc. Proprietary
 Wiring details:

Output: 230VAC, 500W

Outlet mating connector: Harting: insert 09200042611, hood 09200031440
Use wire type UL1015 or equivalent, 16awg (1.44mm2) min.

Wiring chart
Pin number, 5-pin Wire color Pin number, 3-pin Description
connector connector
1 black L L1
2 white N L2
GND green GND PE

278 System Hardware Information System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 User Interface external connections
 Note: the connectors not called out in the diagram have no connection

4 5 6 7

8 9

18 19

10 11 12 13 14 15 16 17
For more information, refer to Wiring diagram user interface/ PC (on page 281).
1 Monitor connector panel
2 Convenience USB port
3 PC [inside the cabinet]

Monitor connector panel connectors

4 Auxiliary USB connector
5 DVI input
6 AC power connector

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) System Hardware Information 279
© 2011 Pressco Technology Inc. Proprietary
 Monitor connector panel connectors
7 Touch screen USB connector

PC connectors
8 2 pin power connector for camera ethernet switch
9 2 pin power connector for PDN ethernet switch
10 Convenience USB port connector
11 Monitor auxiliary USB connector
12 Monitor touch screen USB connector
13 Trackball USB connector
14 Biometric device USB connector
15 DVI connector
16 Ethernet connector for camera ethernet switch (blue cable)
17 Ethernet connector for PDN ethernet switch (green cable)
18 Optional plant network connection
19 Optional remote user interface connection

280 System Hardware Information System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Wiring diagram user interface/ PC
The following diagram shows the wire connections between the monitor, user interface,
and PC.
1 3 4 5
8
8

6 2

7 9

3 9

2
6
1 5 7
11

10

10

1 Monitor auxiliary USB cable

2 Convenience USB port cable
3 DVI cable (included with monitor). (Remove DVI-VGA adapter if present)
4 AC power in for monitor
5 Touchscreen USB cable (for optional touchscreen monitor)
6 Optional Biometric device -USB cable

Do not plug in until application software is installed

7 Trackball USB cable

Do not plug in the PS/2 connector

8 View of monitor connector panel
9 PC. Connectors are inside cabinet.
10 Side cable entry locations

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) System Hardware Information 281
© 2011 Pressco Technology Inc. Proprietary
 11 Cable entry. Route cables behind the PC mounting panel, through the
cable entry at the back of the PC.

Wiring diagram ethernet switches

12

21 13
DETAIL "A"

18
19
17
“A” “A”
21 19
12 13 16 20
18

15 14
14 15

12 Ethernet switch for cameras [on left]

13 Ethernet switch for Pressco Device Network (PDN) [on right]
14 Blue ethernet cable
15 Green ethernet cable
16 Quad ethernet card
17 Two pin power connectors. Cables are included with PC.
18 Two pin power cable
19 Two pin power cable
20 PC
21 Detail "A" Ethernet switch power connection

 Note: the Cat-6 ethernet cabling is divided into two groups. The green cabling goes
to/from the cameras and lighting circuitry. The blue cabling goes to/from the part
tracking circuitry.

282 System Hardware Information System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Wiring diagram trackball
TRACKBALL SWITCH CONNECTIONS

TRACKBALL

TRACKBALL
SWITCHES

INSTALL IN PLACE OF EXISTING

NO F TRACKBALL SWITCH CABLE
COM E INFO

NO H 2
3
COM G CHECK 58473-XX
5

SWITCHES AT TRACKBALL

NO B
COM A INFO

NO D
COM C CHECK

REBOOTING THE INTELLISPEC SYSTEM

You may need to reboot the entire system if power or communication has been lost
between the Vision Processor and the Cluster Box.
Symptoms may include that the inspection module light has stopped flashing, and the
system is no longer taking pictures. Rebooting the system will reconnect the Vision
Processor with the Part Tracker in the cluster box.
 Note: if the power to both the Vision Processor UPS and the Cluster box is
interrupted for more than two minutes, the software will automatically shut itself
down and then shut down the Vision Processor PC. The software will restart. You
will just need to log in and put the system back online.
It may not be necessary to completely reboot the system each time the power to cluster
box is interrupted. Try restarting the application.
Restarting the Application
You must have proper user permissions to exit the software. This prevents unauthorized
system shutdowns. Contact your system administrator if you need user permissions.
To exit Intellispec software:
1. Log in.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) System Hardware Information 283
© 2011 Pressco Technology Inc. Proprietary
 2. Click the Home button .

3. Click the Tools button to display the Tools menu.

4. Click the Exit System option. The Intellispec software shuts down.
5. Connect the Mechanical keyboard (MKB) (on page 34).
6. Press Ctrl + Alt + Delete on the mechanical keyboard.
7. Use the Log Off option to log off of Intellispec.
8. At the Windows Login Prompt, enter ―pvpass― as the password for the Intellispec
user account. Once login is complete the Series V application software will be
launched.
Rebooting the entire system
If restarting the application does not clear the errors, try rebooting the entire system. This
involves shutting down the software, the processor cabinet, and the cluster box (if
applicable).
 Note: The system reboot takes several minutes to complete.
PROCESSOR CABINET SHUTDOWN
You must have proper user permissions to exit the software. This prevents unauthorized
system shutdowns. Contact your system administrator if you need user permissions.
To exit Intellispec software:
1. Log in.

2. Click the Home button .

3. Click the Tools button to display the Tools menu.

4. Click the Exit System option. The Intellispec software shuts down.
To shut down the Processor Cabinet:
1. Connect the Mechanical keyboard (MKB) (on page 34).
2. Press Ctrl + Alt + Delete on the mechanical keyboard.
3. Use the Shutdown option to shut down the PC.
4. Once the PC has shut down, turn off the Processor Cabinet ON/OFF switch. For
location, see Power Up (on page 275).
 Note: The Processor Cabinet ON/OFF switch must be off for approximately 40
seconds before turning it back on for proper restart.
CLUSTER BOX SHUTDOWN
1. Shut off the cluster box external rotary power switch. For location of the power
switch, see the illustration of the cluster box in the Power Up (on page 275) section.
2. If you have a UPS inside the cluster box, open the cluster box and shut off the UPS.
Shutting off the UPS will conserve battery power.
3. Wait at least one minute for all Pressco Devices to fully power down.
CLUSTER BOX POWER UP
1. If you have a UPS inside the cluster box, open the cluster box to turn ON the UPS.
2. Turn ON the cluster box external rotary power switch.
284 System Hardware Information System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 3. Verify the 12VDC, 24VDC, and 48VDC power status indicators of the cluster box
turn ON.
4. Wait at least one minute for all Pressco Devices to fully power up.
PROCESSOR CABINET POWER UP
1. Turn ON the Processor Cabinet ON/OFF switch. The system will launch the
Intellispec software.
2. Log in to the system and begin using the system.
NOTES
If power to the cluster box is interrupted on a cluster box that does not come
equipped with a UPS, the following prompt will be displayed.
"Part Tracker Exception: the Part Tracker has closed its communication port on Lane
n. Reset the Part Tracker and restart the application."
This message is an indication that the Part Tracker and the Application software
communication link has been broken for an extended period of time.

LIGHT TREE
The optional light tree may be mounted on or near an inspection module, or near a cluster
box (if applicable). The optional horn, mounted with the light tree provides an audible
warning.
For more information, refer to Light tree status (on page 285).
Light Tree (optional)
 Red (Alarm)
 Amber (Warning)
 Green (Online)
 Blue (Power)

Light tree status

The lights on the optional light tree will turn on, off, or blink depending on status of
certain hardware. Each lane has its own light tree. The table below lists the different
states for each light.

Light color Condition What it means

Red On - steady Alarm condition
Red On - blinking Part tracker board lost communication with the
host PC or has an error and needs to initiate an
alarm
Red Off No alarm (OK)
Amber On Warning alarm condition

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) System Hardware Information 285
© 2011 Pressco Technology Inc. Proprietary
Light color Condition What it means
Amber Off No warning (OK)
Green On Lane is online
Green Off Lane is offline
Blue On Part tracker board has power (OK)
Blue Off Part tracker board has no power

286 System Hardware Information System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
Chapter 15
INSPECTION MODULE ADJUSTMENTS AND
WIRING DIAGRAMS
This section covers camera adjustments that may be required to keep the inspection
modules working properly. Adjustments include the camera position, aperture, and
camera focus.
The focus adjustment controls the clarity of the image; the aperture adjustment controls
the amount of light admitted by the shutter. Normally the inspection modules do not
require further adjustment after initial system setup. Circumstances that might require
additional adjustments are camera replacement, strobe replacement, or a substantial
change in part size or color.

Danger
The inspection modules are mounted near moving machinery. Use extreme
caution to avoid contact with moving machinery when servicing inspection
modules as serious personal injury could result. Ensure machinery is in an
emergency stop state before servicing inspection modules.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)Inspection Module Adjustments and Wiring Diagrams 287
© 2011 Pressco Technology Inc. Proprietary
 OBSERVE PART IMAGE
When adjusting the focus, aperture, or height for any inspection module, it is helpful to
use Offline Imaging (on page 132) so that you can immediately see the effect of an
adjustment on the image quality. Use the Run feature in Immediate Mode.

To use Run in Immediate Mode:

1. Make sure the lane is offline.

2. Click the desired Sensor button to view Sensor Overview

mode.
3. Right-click the Sensor button to see the Sensor menu.
4. Select Offline Imaging from the menu.
5. Click the Run button under Immediate Mode. The camera will snap pictures
continuously without the need for a part present signal.
While the system is in this mode, you will be able to make adjustments to focus,
aperture, or camera height.

288 Inspection Module Adjustments and Wiring DiagramsSystem Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 EXTENDED I/O IN INSPECTION MODULES
The Extended I/O (see "Extended I/O board" on page 321) kit (optional) is installed
within Chromapulse inspection modules as shown below.

1 power cap
2 Extended I/O kit

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)Inspection Module Adjustments and Wiring Diagrams 289
© 2011 Pressco Technology Inc. Proprietary
 CP/E SERIES MODULES
The CP/E series of inspection modules is a group of modules with similar components.
The module's appearance and adjustments are similar between models. The difference
between model numbers lies in the specific lighting and optics for inspection of different
types of parts. To see your model number, look at the label on the outside of the module.

An Extended I/O (on page 321) kit is available for the CP/ E series inspection modules.
This section covers CP/E models including:

290 Inspection Module Adjustments and Wiring DiagramsSystem Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 CP500E
CP750E
CP1200E
CP1500E
The basic components of the CP/EV module are shown below.

3 8

7
4

1 Power assembly
2 Second driver and light control module (models CP1200E and CP1500E
only)
3 Part Tracker assembly
4 Driver and light control module
5 Fill light module with beam splitter
6 Ethernet switch (mounted on inside wall - not shown)
7 Camera
8 8-port I/O box: CP/ EV inspection module I/O connectors (see
"Chromapulse module external connections" on page 298)

Adjusting the CP/ E Series modules

Module Height Adjustment
The height of the module is easily adjusted. Refer to the illustration below. Loosen the
adjustment knob [item 4] and use the handle [item 3] to move the module up or down.
You can move the module with one hand while viewing the image on the monitor.
Tighten the knob when desired height is achieved.
System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)Inspection Module Adjustments and Wiring Diagrams 291
© 2011 Pressco Technology Inc. Proprietary
 Caution
Loosen only one knob [2 or 4] at a time. Otherwise, the weight of the module
may not be supported.
Adjust for different part size
Move the module up or down to increase or decrease the size of the part image –
Observe Part Image - SV (see "Observe Part Image" on page 288) while adjusting
module.
Use camera position adjustment to adjust for small change in part size - Camera
Position Adjustment (on page 294)
The adjustable stops [items 1 and 5] can be used to mark where the module is
supposed to rest. For example, the bottom stop [item 5] can be placed at the
module‘s lowest inspection height. You can easily raise the module to clean or clear
jams, then lower the module back down to the stop.
The top stop [item 1] can be used to mark the module‘s highest inspection height –
for your largest inspected part.
To adjust module height (or to raise the module for cleaning or clearing
jams):
1. Loosen the adjustment knob [item 4].
Note: if you need a greater range of movement [example: you are changing from
inspecting a shorter part to a much taller part], then loosen knob 2 first. Move
the module using the handle, then tighten knob 2. Then use knob 4 for smaller
adjustments.
2. Use handle [item 3] to move the module up or down.

292 Inspection Module Adjustments and Wiring DiagramsSystem Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 3. Tighten the knob [item 4].

1 Adjustable stop - highest inspection position

2 Range Knob - locks the pivot position in place. Loosen only if you
need to increase the range of movement of the module, move the
module using the handle, then tighten the knob.
3 Handle - use to move the module up or down
4 Adjustment Knob - loosen to move the module, then tighten to
secure the module in place
5 Adjustable stop - lowest inspection position

Switch sides
The CP/E series modules are designed for maximum flexibility to fit into your
production line. During installation, the module can be changed so that the height
adjustment brackets can be placed on the other side of the module.
Likewise, the doors of the module may be removed and their hinges attached to the other
side, for the door to swing oppositely.

Camera Adjustments
If your inspection module has the optional motorized focus and aperture feature, you can
adjust the focus and aperture through the software: Camera Focus and Aperture (on
page 130).

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)Inspection Module Adjustments and Wiring Diagrams 293
© 2011 Pressco Technology Inc. Proprietary
 FOCUS ADJUSTMENT
Look at the part image to observe the adjustments: Observe Part Image - SV (see
"Observe Part Image" on page 288)
To adjust focus, carefully remove or open the inspection module cover. Turn the focus
adjust ring while observing the part image on the monitor. Adjust the focus for the
sharpest image. If needed, adjust the aperture, then reinstall the cover.
APERTURE ADJUSTMENT
The aperture controls the amount of light that passes through the lens. The programmable
light source provides the range of light intensity required for most applications.
However, you can manually adjust the aperture if necessary by turning the aperture
adjust ring on the camera lens. Reinstall the cover.
CAMERA POSITION ADJUSTMENT
 Note: Normally, you do not need to adjust camera position. Adjust only if you are
initially installing, or have replaced the inspection module.
The cameras can be adjusted for image size and position. Carefully remove the side panel
cover of the inspection module. Adjust cameras as necessary while observing image on
Intellispec monitor. After making all camera adjustments, replace module cover.

1 Note camera position on scale when adjusting for your part

2, 3 Additional camera position adjustments - horizontal or vertical on
Intellispec image
4 Camera position - adjust for image size
5 Focus adjustment (or aperture adjustment depending on lens)
6 Aperture adjustment (or focus adjustment depending on lens)

294 Inspection Module Adjustments and Wiring DiagramsSystem Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 REPLACING CAMERA
On rare occasion, you may need to replace a camera in a CP/E inspection module.

To replace camera:
1. Remove the two screws [items 1 and 2].
2. Remove camera from mounting plate and attach new camera.
3. Tighten two screws [items 1 and 2].
4. If necessary, adjust the screws attached to camera bracket [items 3, 4, 5] to square
the image on screen.

Lighting Adjustments
To adjust the lighting, use the software adjustments.
To see the image on the screen:
Observe Part Image (on page 288)
Adjust lighting through either:
Basic adjust lighting (on page 135), or
Advanced adjust lighting (on page 135)
Most often, you will use Basic Adjust Lighting.
LIGHTING ZONES CP500E/ CP750E
These modules use one camera and several lighting zones (see below). The camera and
lighting zone configuration for CP500E and CP750E are the same; however, the angle of
the lighting array of the CP500E is different than that of the CP750E. The illustration
below shows the zone grouping for these modules.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)Inspection Module Adjustments and Wiring Diagrams 295
© 2011 Pressco Technology Inc. Proprietary
 These zones are programmed at Pressco and should not be changed. You may view the
setup in Advanced adjust lighting (on page 135).

CP500E/ CP750E lighting zones

Fill light with beam splitter Main array Ring light (optional)
(optional)
4 zones: 9 zones: 1 zone:
 1 red zone  3 red zones  1 red zone
 1 green zone  2 green zones
 1 blue zone  2 blue zones
 1 IR zone  2 IR zones

CP1200E/ CP1500E
These modules use one camera and several lighting zones (see below). The zone
configuration is similar between these modules, except that the CP1500E has an
additional Lower Light array. The illustration below summarizes the grouping of the
light zones for the CP1200E and CP1500E inspection modules.

296 Inspection Module Adjustments and Wiring DiagramsSystem Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 These zones are programmed at Pressco and should not be changed. You may view the
setup in Advanced adjust lighting (on page 135).

CP1200E lighting zones

Fill light (optional) Upper light Middle light Ring light (optional)

4 zones: 9 zones: 8 zones: 4 zones: OR:

 1 red zone  3 red zones  2 red zones  1 red zone  2 red zones
 1 green zone  2 green zones  2 green zones  1 green zone  2 blue zones
 1 blue zone  2 blue zones  2 blue zones  1 blue zone OR:
 1 IR zone  2 IR zones  2 IR zones  1 IR zone  4 red zones
OR:
 1 red zone

CP1500E
Fill light Upper light Middle light Lower light Ring light (optional)
(optional)
4 zones: 9 zones: 8 zones: 8 zones: 4 zones: OR:
 1 red zone  3 red zones  2 red zones  2 red zones  1 red zone  2 red zones
 1 green zone  2 green zones  2 green zones  2 green zones  1 green zone  2 blue zones
 1 blue zone  2 blue zones  2 blue zones  2 blue zones  1 blue zone OR:
 1 IR zone  2 IR zones  2 IR zones  2 IR zones  1 IR zone  4 red zones
OR:
 1 red zone

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)Inspection Module Adjustments and Wiring Diagrams 297
© 2011 Pressco Technology Inc. Proprietary
 Chromapulse module external connections
 Note: this inspection module is not used in all systems. The configuration of your
inspection module may vary.

BLUE CAMERA
1
GREEN PDN
2

ENCODER
3

8-PORT I/O BOX-MB1

J7 MP2
MACHINE PART 3 J7-4
J7 J8
J8-4 POCKET DETECT PKT DET
J8
MP3 PKT

J5 REJ_CFM2
REJECT CONFIRM2 J5-4
J5 J6
J6-4 MACHINE PART 2 MP1
J6
RC2 MP2

J3 REJ_CFM1
REJECT CONFIRM1 J3-4
J3 J4
J4-2 REJECT2 REJECT2
J4
RC1 REJ2

PART DETECT J1-4 J2-2 REJECT1

J1 PART DET
J1 J2
REJECT1
J2
PD REJ1

MB1

8 port I/O Box MB1

1 Blue cable - Camera
2 Green cable - PDN (Pressco Device Network)
3 Encoder. 8 pin panel connector.
J1 PD Part detect
J2 REJ1 Reject 1
J3 RC1 Reject Confirm 1
J4 REJ2 Reject 2
J5 RC2 Reject Confirm 2

298 Inspection Module Adjustments and Wiring DiagramsSystem Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 8 port I/O Box MB1
J6 MP2 Machine Part 2
J7 MP3 Machine Part 3
J8 PKT Pocket Detect

CP/E inspection module internal connections

This drawing shows the internal wiring typical of inspection modules CP500, CP750,
CP1200, and CP1500.
POWER PANEL
CAMERA1 GIGE
PWR+I/O
66582
57824 58202
ETHERNET

CAMERA2
(IF PRESENT
GIGE
66532 66582
PWR+I/O
57824 58202
66533
ETHERNET

J4
J6
J15 PART TRACKER ETHERNET SWITCH PDN
66582
59860
TP9

J4 J4 J17 J6 J15
P2
J2
J2 RSW2
1
J17 J6 J15

LIGHT TREE 58317 J10

TP5
J9 J9
J4
J4 67740 2
J8 J10
U14

67744 3
J1

(OPTIONAL) J10
J3
U52 U24
J10

4 59860
U15

EXTENDED I/O 66765 J8 J8 U2

U35

P3
J3
(OPTIONAL)
J2

U16

U51 U6
J5
J3

8-PORT I/O BOX 57783 J5 U4 U13

J16
J5
RSW1
U5

J5
GATEWAY
J16
66533 J1
1

J1
J12
J12
J7 P7
J7
J8
(OPTIONAL-SEE PG 4)
J18
J1
J18

J20 J20 J19 J19

J14
J14
J1
C67 C72 C66 C71

ENCODER 65330 J18

J19 65331 65331

J20 65332 65332 J11

67744

ETHERNET SWITCH POWER TERMINATION-12VDC

SEE BELOW
J1

57795 J12

CP500, CP750, CP1200, CP1500

66532 J3
LED CTRL1/DRVR1 IS INSTALLED ON THE SIDE PANEL

LED CTRL1/DRVR1
(ON SIDE PANEL)

ETHERNET SWITCH

1
2
3 CP1200, CP1500-LED CTRL2/DRVR2
4
LED CTRL2/DRVR2 IS INSTALLED ON THE TOP PANEL
57794 67744 5

57795

J1
J11
J12

J2
J3

LED CTRL1/DRVR1 LED CTRL2/DRVR2

(ON SIDE PANEL) (ON TOP PANEL)

ETHERNET SWITCH POWER TERMINATION-12VDC

TWIST THE BLACK AND RED WIRES TOGETHER

65331-XX

6-PIN CONNECTOR
INCLUDED WITH SWITCH

 Note: on Part Tracker assembly, switch RSW1 must be set to '0' for proper operation

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)Inspection Module Adjustments and Wiring Diagrams 299
© 2011 Pressco Technology Inc. Proprietary
 CP500E light array connections
CP500-LIGHT ARRAY CONNECTIONS
J3
SW4
2 4
J1

J4
1 3
U12
J4

J11

U4 U2
J12

U3 U1 J5
J5
SW3

2
3

4
J2

F1

58691
J3 C1 C2 C3 C4

LED CTRL1/DRVR1
(ON SIDE PANEL)

58691

CABLE 58691
UPPER ARRAY

58691

POWER
RINGLIGHT
(OPTIONAL)
CABLE 58691
FILL LIGHT

FILL LIGHT ASSY

(OPTIONAL)
LIGHT ARRAY ASSY
(MAIN PLATE)

CP750E light array connections

CP750-LIGHT ARRAY CONNECTIONS

J4

J5

58691
LED CTRL1/DRVR1
(ON SIDE PANEL)

58691

CABLE 58691
UPPER ARRAY
58691

POW
ER

RINGLIGHT
(OPTIONAL)
CABLE 58691
FILL LIGHT

FILL LIGHT ASSY

(OPTIONAL)
LIGHT ARRAY ASSY
(MAIN PLATE)

300 Inspection Module Adjustments and Wiring DiagramsSystem Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 CP1200E light array connections
CP1200-LIGHT ARRAY CONNECTIONS

J4 J4

J5

58691
LED CTRL1/DRVR1 LED CTRL2/DRVR2
(ON SIDE PANEL) (ON TOP PANEL)

58691
CABLE 58692
CABLE 58691 MIDDLE ARRAY
UPPER ARRAY

58691
58692

POW
ER
RINGLIGHT
(OPTIONAL)
CABLE 58691
FILL LIGHT

FILL LIGHT ASSY

(OPTIONAL)
LIGHT ARRAY ASSY
(MAIN PLATE)

CP1500E light array connections

CP1500-LIGHT ARRAY CONNECTIONS

J4 J4

J5 J5

58692
58691

58711
LED CTRL1/DRVR1 LED CTRL2/DRVR2
(ON SIDE PANEL) (ON TOP PANEL)

58691 58711
CABLE 58711
LOWER ARRAY CABLE 58692
MIDDLE ARRAY

58692
POW
ER

CABLE 58691
UPPER ARRAY

RINGLIGHT
(OPTIONAL)
CABLE 58691
FILL LIGHT

FILL LIGHT ASSY

(OPTIONAL) 58711
LIGHT ARRAY ASSY
(MAIN PLATE)
CABLE 58711
LOWER ARRAY

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)Inspection Module Adjustments and Wiring Diagrams 301
© 2011 Pressco Technology Inc. Proprietary
 CP/E Power Panel connections
CONNECT TO
90-240VAC
PART TRACKER J1
50/60HZ

FAN

L1
BLK-16AWG

L2
66527

GND
LED
WHT-16AWG
INDICATORS
58558

P1

P2
LINE R1 J1

J1
POWER ENTRY
MODULE
N L
L
G
N INTERNAL
VIEW
CB1 R2

G
10A R3

LINE FILTER LOAD

5
EXTERNAL VIEW

66533

66527
66534
MODULE CONNECTOR IEC320-C14

WHT
BLK
MATING CONNECTOR IEC320-C13
POWER DIST PCB

J5
J2

J3
65966

GRN/YEL-16AWG
J5 J2 J3

48VOUT

J6
L1 L2 - +
66528 -
R1 TP7 TP8

J6 TP6 J1 L1
TP5 + C2

J4

3
12V
66532
66529 J7 TP4
TP3
-
+
24V J4

-
CONNECT TO LED
TP2
J7 C3
TP1 + C1

2
48VIN

Pressco Technology, Inc. 2010 ASSY

CTRL1/DRVR1 J3
GROUND STUD

J1
SEE GROUND DETAIL

66530

PS1
USK2
12VDC
SK1 RED

ORG

BLU
1-12V 1
WHT 3 3-NEUT
BLK 4-RET BLK
GRN/YEL-16AWG

4
1 1-LINE 1 5 8
6

5-RET
1-48V
CN5

66530
66529

PS3
PS2 48VDC
24VDC
J1 J3 6
WHT 1 1-NEUT YEL
4-24V 4
CN1
BLK
TERMINATE TO TAB 3 3-LINE
GRN
1-RET 1

1-NEUT
INSTALLED ON COVER.

3-LINE
3 1

WHT
BLK
66529

GROUND STUD POWER ENTRY

HEX NUT
MODULE
STAR WASHER
EARTH GROUND
CAMERA MODULE
EARTH GROUND CIRCUIT
PANEL COVER BREAKER
FLAT WASHER
HEX NUT
STAR WASHER EARTH GROUND FROM
POWER ENTRY MODULE
STAR WASHER

DETAIL "A"
GROUND DETAIL APPLY ITEM 35 LABEL TO TOP OF
FASTEN GROUND LUGS AS SHOWN COVER AT AC POWER ENTRY POINT

302 Inspection Module Adjustments and Wiring DiagramsSystem Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 CP/ E Motorized focus connections (optional)
The following wiring diagram shows the wiring between the motors and controllers for
inspection modules that have the motorized focus option.
MOTORIZED FOCUS CONNECTIONS
(OPTIONAL)
58702

58702

58703

FOCUS
57744

PWR
MOTOR 'X' MOTOR 'Y'

IRIS
GATEWAY PCB
58702 58702

K
K
K
K
K
K
K
D8
D7
D6
D13
D12
D11
D10
12

Y
K
K
2 4 K

Y
SW4 K

PWR
1 3 K
D5
thru

BC2D15
58472 6
J1
D1

+ + BC2D15 STEPPER SO
SI
COMM 58704 J12
U4
T

MOTOR CONTROLLER.
R
P
SS GND M
N
+5V K
L
1 J12 J
H
G
F
6 E
D

GEAR 'X' GEAR 'Y'

C

- -
B
A
JS

16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
U6

UPPER LOWER 1 J13

J14

SLEW
LIM
U1

IO

S1K
R1K
L1

C
J14

A
65332
1
J11

1 3 5
2 4 6
1 J11

D
B
F
GATEWAY POWER 2 U7
2

LIM
H10
LX+ LY+
U9

2
O1
LIM
+
O1
LIM
+
CONNECT TO PART H5
1
SW3
1

4
O2 O2
LIM
-
LIM
- TRACKER MOTHERBOARD J20
LX- LY-
LIMIT SWITCH PCB
J1 J1
58485 LIMIT SWITCH PCB
58485 LIM 'Y' CONNECTOR
LIM 'X' CONNECTOR
58556

CAMERA ASSEMBLY

MOTOR 'X'
MOTOR 'Y'

LIM 'X' CONNECTOR

LIM 'Y' CONNECTOR

GEAR 'Y' GEAR 'X'

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)Inspection Module Adjustments and Wiring Diagrams 303
© 2011 Pressco Technology Inc. Proprietary
 CP4422EV INSPECTION MODULE
The CP4422E inspection module provides comprehensive inside of can inspection. The
module can be configured with up to four cameras to inspect the flange, neck, and body
of the can. The main components of the CP4422E are shown below. Note that your
system may not contain all components shown.
The color of the arrays and filters on the cameras dictates what color the camera sees.
The Neck camera sees only red light. The Body camera sees only blue light. The Flange
camera sees only green light.
An Extended I/O (on page 321) kit is available for the CP4422E.

1 Flange camera with Green Pass filter installed

2 Neck camera with Red Pass filter installed
3 Ethernet switch
4 Body camera with Blue Pass filter installed
5 Plate or space for Auxiliary module

304 Inspection Module Adjustments and Wiring DiagramsSystem Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 6 Beam splitter/ mirror assembly
7 First surface mirror
8 Periscope assembly for body camera
9 Window - neck and flange cameras look through
10 Body, flange, and neck arrays inside
11 Ellipsoidal mirror inside
An auxiliary module may be installed to provide additional inspection (the area
inspection depends on your application). It is installed in place of the plate [item 5]. An
example auxiliary module is shown below.

Adjusting the CP4422EV module

Camera Adjustments
If your inspection module has the optional motorized focus and aperture feature, you can
adjust the focus and aperture through the software: Camera Focus and Aperture (on
page 130).
FOCUS ADJUSTMENT
Look at the part image to observe the adjustments: Observe Part Image - SV (see
"Observe Part Image" on page 288)
To adjust focus, carefully remove or open the inspection module cover. Turn the focus
adjust ring while observing the part image on the monitor. Adjust the focus for the
sharpest image. If needed, adjust the aperture, then reinstall the cover.

Lighting Adjustments
To adjust the lighting, use the software adjustments.
To see the image on the screen:
Observe Part Image (on page 288)
System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)Inspection Module Adjustments and Wiring Diagrams 305
© 2011 Pressco Technology Inc. Proprietary
 Adjust lighting through either:
Basic adjust lighting (on page 135), or
Advanced adjust lighting (on page 135)
Most often, you will use Basic Adjust Lighting.
LIGHTING ZONES CP4422E
The illustrations and table below show the lighting zone grouping for the CP4422E
inspection module. The illustration shows a module with three cameras installed.
 Note: These zones are programmed at Pressco and should not be changed. You may
view the setup in Advanced adjust lighting (on page 135).

Sidewall/ Sidewall/
Dome (Body) Flange Dome (Body)

Neck Neck

CP4422E Lighting Zones

Body Neck Flange

(upper array type) (lower array type) (ring array type)
10 blue zones 1 red zone 3 green zones

CP4422E module external connections

 Note: this inspection module is not used in all systems. The configuration of your
inspection module may vary.

306 Inspection Module Adjustments and Wiring DiagramsSystem Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 1
2
3
4

8-PORT I/O BOX-MB1

J7 MP2
MACHINE PART 3 J7-4
J7 J8
J8-4 POCKET DETECT PKT DET
J8
MP3 PKT

J5 REJ_CFM2
REJECT CONFIRM2 J5-4
J5 J6
J6-4 MACHINE PART2 MP1
J6
RC2 MP2

J3 REJ_CFM1
REJECT CONFIRM1 J3-4
J3 J4
J4-2 REJECT2 REJECT2
J4
RC1 REJ2

PART DETECT J1-4 J2-2 REJECT1

J1 PART DET
J1 J2
REJECT1
J2
PD REJ1

MB1

8 port I/O Box MB1

1 Green cable - PDN (Pressco Device Network)
2 Blue cable - Camera
3 Light tree cable
4 Encoder. 8 pin panel connector.
J1 PD Part detect
J2 REJ1 Reject 1
J3 RC1 Reject Confirm 1
J4 REJ2 Reject 2

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)Inspection Module Adjustments and Wiring Diagrams 307
© 2011 Pressco Technology Inc. Proprietary
 8 port I/O Box MB1
J5 RC2 Reject Confirm 2
J6 MP2 Machine Part 2
J7 MP3 Machine Part 3
J8 PKT Pocket Detect

CP4422EV internal connections page 1

F1291W page 1 of 3
LED FAN PART
BLK-16AWG
INDICATORS 66527 TRACKER
WHT-16AWG
58558 J22

R1 J1

J1

P1

P2
R2 LINE
R3 CB1 L
G
N INTERNAL
VIEW
5A
LOAD

5
WHT
BLK
66921

66527

66926

GRN/YEL-16AWG
PS1
SK2

SEE "GROUND DETAIL"

SK1 12VDC RED
WHT 1-12V 1

3
3-NEUT BLK
BLK 4-RET 4
1
1-LINE

GROUND STUD
6

POWER DIST PCB

J4
66925
66923

65966
66926

TP7 TP8

J4
+

C2

C3

Pressco Technology, Inc. 2010 ASSY

48VOUT
-

PS2
C1

J3
J3

J1

66924
24VDC
J3
L1
R1

3 2
6
WHT YEL
1-NEUT J2
J2

BLK 4-24V 4 4 1

3
3-LINE GRN J1
1-RET J5
J1

1
-
+

-
+

-
+
48VIN
12V

24V
J5

TP6
TP5

TP4
TP3

TP2
TP1

GRN/YEL-16AWG
J7
J6
L2
L1
66925

PS3 CN5
J6

J7

CN1 48VDC ORG

66925

1-48V
1

BLK 3-LINE
3

WHT BLU SEE NOTE 1

5-RET
5

1-NEUT
1

66924
8

NOTES:
66925 1) TERMINATE TO GROUND TAB INSTALLED ON COVER.
66923

66923

66923

GROUND STUD

90-240VAC HEX NUT

50/60HZ STAR WASHER
EARTH GROUND
CAMERA MODULE
EARTH GROUND
L1
L2
GND

PANEL COVER
FLAT WASHER
HEX NUT
STAR WASHER EARTH GROUND FROM
POWER ENTRY MODULE
N L
POWER ENTRY STAR WASHER

G MODULE
LINE FILTER
EXTERNAL VIEW

MODULE CONNECTOR IEC320-C14

MATING CONNECTOR IEC320-C13 GROUND DETAIL
FASTEN GROUND LUGS AS SHOWN

308 Inspection Module Adjustments and Wiring DiagramsSystem Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 CP4422EV internal connections page 2
F1291W page 2 of 3
POWER 66926 59861

J22
J22 J18
J1
66922
J18
J13
J17

J4
J12
J19 J19 66914
LIGHT TREE

J8
U15 U16

J4

J10
J21
J11

J2
J20

U6
U14
J10

U35

J5
U51
J15

P2

P7
J2

J7
U24
J9

U13
J16

U2

J7
J23
J6 J2 J7

U5
U52

U4
J25 J24

J3
J5

P3
J3

RSW1
J1 J2 J3
J27

J4
66919 J4 J14 J8
J25

J14

PART TRACKER PCB ASSY

J1

66458
J1

65330

66920
STR-
CAM+
CAM-

STR+
R1

TP8
48V

TP4

TP3

TP2

TP1

+
48V
D1

J9
J2
R3
R2
R4

J3

J8
ENCODER MB1
J4
D4

D2
STROBE

+ +
12V
J7

J6

D3
CAMERA

J5

+
12V
TP6

66922

DIST BD1
59130

PDN SWITCH
(GREEN CABLES)

1 59861
2
3
4
5 PDN
6
7 PART TRACKER
8 59861 HOST PC

66582 FERRITE

6-PIN CONNECTOR
INCLUDED WITH SWITCH
5 5-BLK/18AWG
2
3
4

6 6-RED/18AWG
1

SEE DETAIL "A" below

 Note: on Part Tracker assembly, switch RSW1 must be set to 'F' for proper operation

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)Inspection Module Adjustments and Wiring Diagrams 309
© 2011 Pressco Technology Inc. Proprietary
 Detail "A"
DETAIL "A"

66922-XX
ETHERNET SWITCH POWER TERMINATION-12VDC
PIN 6 - 12V(RED) TWIST THE BLACK AND RED WIRES TOGETHER
PIN 5 - COM(BLK)

6-PIN CONNECTOR
INCLUDED WITH SWITCH

310 Inspection Module Adjustments and Wiring DiagramsSystem Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 CP4422EV internal connections page 3
F1291W page 3 of 3
PDN SWITCH
(GREEN CABLES)

1
2
3
4
5
6 LED CTRLR1 59862
7

FLANGE (CAMERA3)
GROUND SWITCHES
ETHERNET

TO PANEL
PWR+I/O
SEE DETAIL "B"

CAMERA SWITCH
(BLUE CABLES) NECK (CAMERA2)
ETHERNET
1
2 PWR+I/O

3
4
5 FLANGE (CAMERA3) BODY (CAMERA1)
CAMERAS 6 NECK (CAMERA2)
ETHERNET
7 BODY (CAMERA1)
59847 HOST PC 8 PWR+I/O

66582 FERRITE

6-PIN CONNECTOR PDN SWITCH

5 5-BLK/18AWG

5 5-BLK/18AWG
2

2
3
4

6 6-RED/18AWG

3
4

6 6-RED/18AWG
1

INCLUDED WITH SWITCH POWER CONNECTOR

INSTALL JUMPER WIRES FOR

POWER FROM PDN SWITCH
PIN 6 - 12V(RED)
PIN 5 - COM(BLK) 66582
FLANGE CAMERA

66582
NECK CAMERA

66582
BODY CAMERA
FLANGE CAMERA

59862

J1
CONNECT TO
NECK CAMERA

J3

J1
SW4
2 4
LIGHT ARRAY
J4
BODY CAMERA

1 3
U12
J4

J11

66917 J12 J12

U4 U2 66913

U3 U1 J5
J5
SW3
1

2
J2
J3
J4
J5

J2
F1

STR-

STR+

CAM-
TP1

TP2

TP3
J3 J3 C1 C2 C3 C4
CAM+ TP4

66919 J1
J3 J4 J5
J2
R2 D2 12V TP6
+

12V
R3 D3
+

R4 D4 CAMERA
+

STROBE
J1
TP8 48V

LED CTRL1/DRVR1
+

J6
48V D1
J9

J8

J7

66459
R1

DIST BD1
J9

59130
66915

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)Inspection Module Adjustments and Wiring Diagrams 311
© 2011 Pressco Technology Inc. Proprietary
 Detail "B"
GRN/YEL-16AWG

DETAIL "B"
ETHERNET SWITCH GROUND
TRIM WIRES TO FIT

CP4422EV auxiliary module internal connections

PDN SWITCH
(GREEN CABLES)
1
2
3
4
5 LED CTRLR2 59860
6
7
8

CAMERA SWITCH
(BLUE CABLES)
J3
1 J1 J1
SW4
2 4

2 J4
3
U12
1

AUX (CAMERA4) J4

3 ETHERNET 66582 J11

4 AUX (CAMERA4) AUX CAMERA 66709 J12 J12

U4 U2

5 PWR+I/O
J5
J5
6 U3 U1

SW3
7

2
J2
J3

4
8 J2

F1
STR-

STR+

CAM-
TP1

TP2

TP3
J3 J3 C1 C2 C3 C4
CAM+ TP4

66919 J1
J3 J4 J5
J2
R2 D2 12V TP6
+

12V
R3 D3
+

R4 D4 CAMERA
+

STROBE
J1
TP8 48V

LED CTRL2/DRVR2
+

J6
48V D1
J9

J8

R1 J7

DIST BD2 66459

59130
J9

66916

66913
J22 J18
J1
66919

J13
J17

J19
J12
J8

U15 U16
J4

J10

J21
J11
J2

J20

CONNECT TO
U6
U14

J10

LIGHT ARRAY
U35

J5
U51

J15
P2

P7
J2

J7
U24

J9
J9
U13

J16
U2

J7

J23
J6 J2 J7
U5
U52

U4

J25 J24
J3

J5
P3
J3

RSW1

J1 J2 J3
J27

J4
J14 J8

PART TRACKER PCB ASSY

66458

312 Inspection Module Adjustments and Wiring DiagramsSystem Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 CP500 INSPECTION MODULE
The CP500 inspection module is in a smaller package for confined spaces. It inspects
mostly smaller crowns and closures.
The CP500 is shown below.

CP500 outside view CP500 inside view with covers removed

1 - Camera

Adjusting the CP500/ V module

Camera Adjustments
If your inspection module has the optional motorized focus and aperture feature, you can
adjust the focus and aperture through the software: Camera Focus and Aperture (on
page 130).

Lighting Adjustments
To adjust the lighting, use the software adjustments.
To see the image on the screen:
Observe Part Image (on page 288)
Adjust lighting through either:
Basic adjust lighting (on page 135), or
Advanced adjust lighting (on page 135)
Most often, you will use Basic Adjust Lighting.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)Inspection Module Adjustments and Wiring Diagrams 313
© 2011 Pressco Technology Inc. Proprietary
 LIGHTING ZONES CP500
The lighting zones are the same as the CP500E inspection module. See Lighting zones
CP500E/ CP750E (on page 295).

CP500 inspection module internal connections

ASSEMBLIES W/O MOTORIZED FOCUS

CAMERA CAMERA
66582 ETHERNET 66582
58283 59286
PWR+I/O

J2
C2

GND C3

66583 J2

66687 J1
J3 J4 J5
STR- R4 D4 STR+

+
C1 CAM- R3 D3 CAM+

+
12VC R2
R5 D2 12V

+
J1
48V
J6
R1

+
48VC 48V D1
J9 J8 J7

DIST PCB
59130

ASSEMBLIES W/ MOTORIZED FOCUS

PDN
66582
59860

CAMERA CAMERA
66582 66582
58283
ETHERNET
59286 GATEWAY PCB
PWR+I/O 57744

K
K
K
K
K
K
K
D8
D7
D6
D13
D12
D11
D10
12

K
K

J1 SW4
2

1
4

3
K
K
K
K
J2

D5
thru
D1
J1
6
U4
T
R
P
N
M
L
C2 1 J12
K
J
H
G
GND C3 F

66583
6 E
D
C
B
J2 A

66687 J1
16
15
14
13
12
11
10
J3 J4 J5

9
8
7
6
5
4
3
2
1
U6

STR- R4 D4 STR+
+

C1 CAM- R3 1 J13
D3 CAM+
+

J6
12VC R2

J11
U1
R5 D2 12V L1
+

J14

C
E

A
1

1 3 5
J1

2 4 6
48V 1 J11
J6

59260
H

D
B
F
R1
+

2
48VC 48V D1 2 U7
J9 J8 J7
U9 1
H10

2
H5 SW3
1 1
3

DIST PCB
59130

314 Inspection Module Adjustments and Wiring DiagramsSystem Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 CP500 Motorized focus connections (optional)
The following wiring diagram shows the wiring between the motors and controllers for
inspection modules that have the motorized focus option.
ASSEMBLIES W/ MOTORIZED FOCUS

58468

58468

58477

FOCUS
MOTOR 'X' MOTOR 'Y' 57744

PWR
IRIS
58468 58468 GATEWAY PCB

K
K
K
K
K
K
K
D8
D7
D6
D13
D12
D11
D10
12

Y
K
K
K
2 4 K

Y
SW4 K

PWR
1 3 K
D5
thru

BC2D15
D1
J1
6

+ + SO
SI
COMM 58471 J12 U4
T
P
R
SS GND M
N
+5V K
L
1 J12 J
H
G
F

GEAR 'X' GEAR 'Y' 6 E

D
C

- -
B
A
JS

16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
U6

UPPER LOWER
1 J13

J14

SLEW
LIM
U1

IO

S1K
R1K
L1

C
J14

A
1

1 3 5
2 4 6
1 J11

D
B
F
58472 2 U7
2

LIM
H10
LX+ LY+
U9

2
O1
LIM
+
O1
LIM
+
BC2D15 STEPPER H5
1
SW3
1

4
O2 O2
LIM LIM
- -

LIMIT SWITCH PCB LX- LY- MOTOR CONTROLLER.

58485 J1
LIMIT SWITCH PCB
J1

58485 LIM 'Y' CONNECTOR

LIM 'X' CONNECTOR
58556

CAMERA ASSEMBLY

MOTOR 'X'

MOTOR 'Y'

LIM 'X' CONNECTOR

LIM 'Y' CONNECTOR

GEAR 'Y' GEAR 'X'

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)Inspection Module Adjustments and Wiring Diagrams 315
© 2011 Pressco Technology Inc. Proprietary
 CPX INSPECTION MODULE
The CPX module contains the lighting and optics to inspect the decoration on the outside
of cans to detect mixed labels and gross decorator defects. The basic components of the
inspection module are shown below.
CPX FRONT VIEW (WITH DOOR REMOVED)

1 Light control board

2 Camera 1
3 Camera 2
4 Signal distribution board
5 LED light source (quantity 4)
6 First surface mirror for optics (one on each side of module)
7 First surface mirror for optics (one on each side of module)
8 Glass shield

316 Inspection Module Adjustments and Wiring DiagramsSystem Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 CPX BACK VIEW

1 Blue cable - Camera 2 connector

2 Blue cable - Camera 1 connector
3 Green cable - PDN (Pressco Device Network)
4 Photoelectric sensor "Smarteye"
5 Part detector cable
6 Part detector cable

Adjusting the CPX camera

The camera can be moved up or down for fine tuning the image. The focus and aperture
can be adjusted manually if necessary.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)Inspection Module Adjustments and Wiring Diagrams 317
© 2011 Pressco Technology Inc. Proprietary
  Note: The camera inspects the top five inches of a can, or the whole length of a 12
ounce can. This adjustment is not for large adjustments.

1 Camera adjust to fine tune the image area

2 Aperture adjust
3 Focus adjust

Camera Adjustments
If your inspection module has the optional motorized focus and aperture feature, you can
adjust the focus and aperture through the software: Camera Focus and Aperture (on
page 130).

Lighting Adjustments
To adjust the lighting, use the software adjustments.
To see the image on the screen:
Observe Part Image (on page 288)
Adjust lighting through either:
Basic adjust lighting (on page 135), or
Advanced adjust lighting (on page 135)
Most often, you will use Basic Adjust Lighting.
LIGHTING ZONES CPX
The lighting zones for the CPX module consist of the right side and the left side.
Lighting adjustments make either side brighter or darker.

318 Inspection Module Adjustments and Wiring DiagramsSystem Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 CPX internal connections

CAT 6
CAT 6

58624C

CAMERA 1 CAMERA 2

PWR+I/O PWR+I/O

59289C
ETHERNET ETHERNET

F1242C
CAT 6

F1241C
F1241C

F1348C

58624C

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)Inspection Module Adjustments and Wiring Diagrams 319
© 2011 Pressco Technology Inc. Proprietary
Chapter 16
EXTENDED I/O
This section contains information about the optional Extended I/O board.

EXTENDED I/O BOARD

This optional module provides additional input and output ports for communicating with
the Intellispec Series V system. The board may be installed within a cluster box or within
an inspection module (see "Extended I/O in inspection modules" on page 289). The
board is connected to the lane's Part Tracker board via a ribbon cable.
 Note: Each Extended I/O board handles only one lane.
 Note: Extended I/O is not available with an Embedded Cluster Box.
Some signals must be enabled in the software through the Extended I/O Configuration
(on page 328).

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Extended I/O 321
© 2011 Pressco Technology Inc. Proprietary
 Below is the basic layout for the Extended I/O module.

PREFORM ALARM
CLEAR STATS 7
CLEAR ALARMS

PROCESSED
PRINT STATISTICS

PART NOT
PART AT REJECT
PART BAD
PART PRESENT
PART GOOD
SYSTEM STATE 0

24V

7
15

INSPECTION
INSPECTION

ALARM
ALARM

0
8
24V

7
15
GROUP
GROUP

0
8
24V
RS-232 PORT RCV
RS-232 PORT TR INPUT PORT STROBE
OUTPUT PORT STROBE 7
7
INPUT PORT
GENERIC
OUTPUT PORT
GENERIC

0
0
24V

Extended I/O signals

The Series V Extended I/O signals are listed in the table below. For the location on the
Extended I/O board, refer to the Extended I/O terminal block reference (on page 326).
 Note: some signals are not currently used

322 Extended I/O System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 All Extended I/O inputs are PNP. Outputs are selectable to be either open collector or
open emitter. However, that selection applies to ALL output signals.
The input and power LEDs are visual indicators. The output LEDs illuminate if the
current reaches 40mA or higher, which is approaching maximum current. The maximum
current output is 50mA. See also information about Extended I/O circuits (on page 326).
*The signals marked with an asterisk must be enabled through Extended I/O
Configuration (on page 328) in the software.

Signal I/O Connector Indicator LED Comments/ Reference

Clear Stats* I J4-23 D2 Clears the lane statistics
Clear Alarms* I J4-22 D3 Clears the lane alarms
Print Statistics* I J4-21 D4 Prints the lane statistics to currently
configured printer or file
Schedule Reports (on page 88)
Preform Alarm I J4-24 D1 Used only in special applications.
Activated by the Preform Material
Handling system.
System State* O J4-16 D11 Indicates whether the lane is online or
offline. Online = active. Offline =
inactive.
Part Present (Part O J4-18 D9 Pulses for 12 ms when the part present
Detect)* sensor detects a part
Part Good* O J4-17 D7 Pulses for 12 ms for each part declared
good by the inspection
Part Bad* O J4-19 D5 Pulses for 12 ms for each part declared
bad by the inspection
Part at Reject* O J4-20 D13 Pulses for 12 ms for each part the
crosses the reject point (online mode
only)
Group 0 O J2-3 D17 Pulses for 12 ms when an inspection
fails in the user-defined group (online
Group 1 O J2-4 D25 mode only)
Group 2 O J2-5 D33 Walk By Setup (on page 71)
Group 3 O J2-6 D41
Group 4 O J2-7 D15
Group 5 O J2-8 D23
Group 6 O J2-9 D31
Group 7 O J2-10 D39
Group 8 O J2-15 D21
Group 9 O J2-16 D29
Group 10 O J2-17 D37
Group 11 O J2-18 D45
Group 12 O J2-19 D19
Group 13 O J2-20 D27
Group 14 O J2-21 D35

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Extended I/O 323
© 2011 Pressco Technology Inc. Proprietary
Signal I/O Connector Indicator LED Comments/ Reference
Group 15 O J2-22 D43
Part Not Processed 0 O J4-3 D109 Pulses for 12 ms when a part is not
processed due to a system malfunction
Part Not Processed 1 O J4-4 D113 (online mode only)
Part Not Processed 2 O J4-5 D117
Part Not Processed 3 O J4-6 D121
Part Not Processed 4 O J4-7 D107
Part Not Processed 5 O J4-8 D111
Part Not Processed 6 O J4-9 D115
Part Not Processed 7 O J4-10 D119
Inspection Alarm 0 O J3-3 D59 Pulses when the associated alarm
condition occurs and stays active until
Inspection Alarm 1 O J3-4 D67 the alarm is cleared
Inspection Alarm 2 O J3-5 D75 Lane Alarm Configuration (on page
78)
Inspection Alarm 3 O J3-6 D83
and
Inspection Alarm 4 O J3-7 D57
Sensor Alarm Configuration (on page
Inspection Alarm 5 O J3-8 D65 81)

Inspection Alarm 6 O J3-9 D73

Inspection Alarm 7 O J3-10 D81
Inspection Alarm 8 O J3-15 D63
Inspection Alarm 9 O J3-16 D71
Inspection Alarm 10 O J3-17 D79
Inspection Alarm 11 O J3-18 D87
Inspection Alarm 12 O J3-19 D61
Inspection Alarm 13 O J3-20 D69
Inspection Alarm 14 O J3-21 D77
Inspection Alarm 15 O J3-22 D85
Generic Input Port 0 I J1-3 D48 Reserved for future use
Generic Input Port 1 I J1-4 D50
Generic Input Port 2 I J1-5 D51
Generic Input Port 3 I J1-6 D52
Generic Input Port 4 I J1-7 D55
Generic Input Port 5 I J1-8 D56
Generic Input Port 6 I J1-9 D47
Generic Input Port 7 I J1-10 D49
Input Port Strobe I J1-11 D53 Reserved for future use
Generic Output Port 0 O J1-15 D91 Reserved for future use
Generic Output Port 1 O J1-16 D95
Generic Output Port 2 O J1-17 D101
Generic Output Port 3 O J1-18 D105
324 Extended I/O System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
Signal I/O Connector Indicator LED Comments/ Reference
Generic Output Port 4 O J1-19 D89
Generic Output Port 5 O J1-20 D93
Generic Output Port 6 O J1-21 D99
Generic Output Port 7 O J1-22 D103
Output Port Strobe O J1-23 D97 Reserved for future use
RS-232 Port TR O J1-24 D202 Reserved for future use
RS-232 Port RCV I J1-12 D200 Reserved for future use

All Connectors
Function Pin
Isolated ground 1, 2
24 V (isolated) 13, 14

Test Points
Function Test Point
24 V 2
24 V Gnd 3
3.3 V 1
3.3 V Gnd. 4

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Extended I/O 325
© 2011 Pressco Technology Inc. Proprietary
 Extended I/O terminal block reference
c 2010 Pressco Technology Inc.
TP3 TP4

J4-P12
J4-P24
J4-P11
J4-P23
J4-P10
J4-P22
J4-P9
J4-P21
J4-P8
J4-P20
J4-P7
J4-P19
J4-P6
J4-P18
J4-P5
J4-P17
J4-P4
J4-P16
J4-P3
J4-P15
J4-P2
J4-P14
J4-P1
J4-P13
J3-P12
J3-P24
J3-P11
J3-P23
J3-P10
J3-P22
J3-P9
J3-P21
J3-P8
J3-P20
J3-P7
J3-P19
J3-P6
J3-P18
J3-P5
J3-P17
J3-P4
J3-P16
J3-P3
J3-P15
J3-P2
J3-P14
J3-P1
J3-P13
J2-P12
J2-P24
J2-P11
J2-P23
J2-P10
J2-P22
J2-P9
J2-P21
J2-P8
J2-P20
J2-P7
J2-P19
J2-P6
J2-P18
J2-P5
J2-P17
J2-P4
J2-P16
J2-P3
J2-P15
J2-P2
J2-P14
J2-P1
J2-P13
J1-P12
J1-P24
J1-P11
J1-P23
J1-P10
J1-P22
J1-P9
J1-P21
J1-P8
J1-P20
J1-P7
J1-P19
J1-P6
J1-P18
J1-P5
J1-P17
J1-P4
J1-P16
J1-P3
J1-P15
J1-P2
J1-P14
J1-P1
J1-P13

TP1 TP2

Extended I/O circuits

The following illustrations show typical input and output circuits you can use to
communicate with your plant's PLC, or to connect external LEDs or light trees.

326 Extended I/O System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Specifications:
Minimum dwell time of the input device is 1.1 ms
Maximum output load is 50 mA
Default value of output pulse is 12ms. Some output signals, such as alarms, must be
cleared on the Intellispec before they turn off.

The following illustration shows a typical circuit that can be used to clear alarms.

The following illustration shows a typical circuit that can be used for a group output.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Extended I/O 327
© 2011 Pressco Technology Inc. Proprietary
 EXTENDED I/O IN INSPECTION MODULES
The Extended I/O (see "Extended I/O board" on page 321) kit (optional) is installed
within Chromapulse inspection modules as shown below.

1 power cap
2 Extended I/O kit

EXTENDED I/O CONFIGURATION

Through this menu you can enable input or output signals to either perform a function on
the Intellispec system or allow you to monitor the production lane in your plant. These
settings must be done for each Extended I/O board for each lane.
See also the sections about Extended I/O (see "Extended I/O board" on page 321) and
Extended I/O Signals (on page 322).
To get to this screen:

From the Lane or Sensor Overview screen, click the tools button to see the
Tools Menu, then select Hardware Setup, then select Extended I/O Configuration.
This screen displays some of the inputs and outputs on the optional extended I/O board.

328 Extended I/O System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 If one of the extended I/O ports is used it must be enabled here in the software, and the
hardware must be connected appropriately.

INPUT INTERRUPTS
These signals produce an input pulse to the Intellispec processor to perform the following
functions.
Clear Alarms Interrupt
Clears the lane alarms.
Clear Statistics Interrupt
Clears the lane statistics.
Print Statistics Interrupt
Prints the lane statistics to the currently configured printer or file. See also Schedule
Reports (on page 88).
OUTPUT
System State
Produces an output pulse to notify your plant whether the lane is online or offline.
Online = active. Offline = inactive.
PART DETECT MASK
Choose which Part Detect or other input events to trigger the Part Present output on the
Extended I/O board. This is an OR function. Any enabled Part Detect signal or Input
Event that goes active will activate the Extended I/O Part Present output.
Part Detect
The signal goes active when the sensor detects a part.
Input Event N
The Part Tracker board accepts up to five* input events (Part detectors or other
sensors). Part tracking is always controlled by the Part Detect signal (Input Event 0).
You might use other input events (1 - 4) in your system to trigger the Part Present
output signal.
*Only if your system has an 8-channel Part Tracker board. If your system has a
2-channel Part Tracker board, then only one Part Detect signal is used. The other
input events are not available.
PART GOOD MASK
Choose which rejector(s) signal to activate the Part Good output on the Extended I/O
board. After a part is inspected, the system determines whether the part is good or bad.
As a good part passes the rejecter**, the system can trigger the Part Good output on the
Extended I/O board. This is an OR function. Any enabled rejector that has a good part
passing by will activate the extended I/O Part Good output.
System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Extended I/O 329
© 2011 Pressco Technology Inc. Proprietary
 PART BAD MASK
Choose which rejector(s) signal to activate the Part Bad output on the Extended I/O
board. After a part is inspected, the system determines whether the part is good or bad.
As a bad part passes the rejecter**, the system can trigger the Part Bad output on the
Extended I/O board. This is an OR function. Any enabled rejector that has a bad part
passing by will activate the extended I/O Part Bad output.
**If your system has a 2-channel Part Tracker board, then the lane has up to two
rejectors. If your system has an 8-channel Part Tracker board, then the lane has up to four
rejectors.

330 Extended I/O System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
Chapter 17
MAINTENANCE FREQUENCY
Follow the guidelines for cleaning and maintenance of the Intellispec system and the
inspection modules.

Intellispec Processor Cabinet and General Components

Item Description Once per Once per
day or shift month
Observe Proper Verify that defective parts are being rejected by inserting X
inspection a known defective part through inspection
Observe Proper Verify that no stray parts are stuck in or near the X
inspection inspection module or reject station
Observe Proper Verify that no buildup of dirt or contaminants has X
inspection occurred on inspection module, part detector, or
conveyor. Clean if necessary.
Observe Proper Verify that each sensor image is properly centered, X
inspection focused, and properly lit. Adjust if necessary.
Vision Processor Rinse in clean water; use mild soap and water solution if X
filter oily. Cleaning the Vision Processor filter (on page 332)
Cluster Box Rinse in clean water; use mild soap and water solution if X
filters (if oily. Cleaning the Cluster Box filters
applicable)

Inspection Modules Chromapulse

Item Description Once per Once per
day or shift month
Part Detect Sensor Clean with soft, clean, oil-free cloth dampened with Once per
and Reflector mild soap and water solution. Wipe dry. week
Cleaning the Part Detector (on page 336)
Camera lens Clean only with lens tissue and lens cleaner. Be X
careful not to alter focus or aperture.
Cleaning the Camera Lens (on page 335)
Glass surfaces: Clean with soft, clean, oil-free cloth dampened with X
Beam Splitter and lens cleaning solution.
Secondary lens Cleaning the Chromapulse Beam Splitter (on page
334)
Ellipsoidal mirror Normally does not need cleaning. If dirty, blow off dust Only if dirt
with compressed air, and follow instructions. appears on
Cleaning the Ellipsoidal Mirror (on page 336) image
Plastic surfaces: Clean with soft, clean, oil-free cloth dampened with X
Dome light or Ring mild soap and water solution. Wipe dry.
light diffusers

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Maintenance Frequency 331
© 2011 Pressco Technology Inc. Proprietary
Fan filters Rinse in clean water; use mild soap and water solution X
CP4422EV if oily. Cleaning the Chromapulse Fan Filters (see
"Replacing/ Cleaning the Chromapulse CP4422EV
Fan Filters" on page 333)
Filter/ Regulator Replace filters Oil removal filter - replace
Replacing Filter/ Regulator Filters (on page 338) every 2000 hours
Oil vapor removal filter -
replace every 12 months

CLEANING THE VISION PROCESSOR FILTER

The filter for the vision processor should be cleaned once a month for best results. The
filter is located underneath the user interface cabinet. Replace with a new filter when
necessary.
 Note: Frequency of cleaning will depend upon plant conditions

To clean the filter:

1. With your fingers, pull down the front of the grate [item 2]. The grate is hinged, and
opens wide enough to remove the filter.
2. Remove the filter [item 1] and clean it.
 If the filter contains dry dust and dirt, rinse it in plain water
 If the filter contains oily dust and dirt, clean it in soapy water, then rinse in clear
water
3. Dry the filter completely, then place it back underneath the user interface cabinet.
4. Push the grate closed.

1
2

1 Part number 66621 - filter for vision processor

332 Maintenance Frequency System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 2 Grate to hold filter in place

REPLACING/ CLEANING THE

CHROMAPULSE CP4422EV FAN FILTERS
We recommend that you replace the filters once a month, using the part number listed
below.
If you do not have replacement filters, clean them once per month. Remove the covers to
access the filters.
 If the filter contains only dry dust and dirt, rinse it in plain water
 If it contains oily dust and dirt, clean it in soapy water

To replace a filter, use the part number listed below:

Part Number Description
1 66446 Replacement filter element (same part number is
used in both locations)

CLEANING OPTICAL SURFACES

Important
Debris and contamination could build up on both the glass and plastic surfaces.
This dirt could appear in the inspection windows, causing false rejects of
parts, or it could degrade lighting. Clean glass and plastic surfaces often to
avoid false rejects.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Maintenance Frequency 333
© 2011 Pressco Technology Inc. Proprietary
 To maintain proper image quality and system performance, the clear glass and plastic
surfaces on the Inspection Modules must be cleaned on a regular basis. Dirt and debris
that appear in the image can cause false rejects. An oily film on optical surfaces can
cause false rejects or missed defects.

CLEANING GLASS SURFACES

Glass surfaces that may require cleaning are:
Camera Lens
Beam Splitter (if present)
Secondary lens (if present)
Secondary mirror (if present)
To clean glass surfaces:
Blow off dust with canned, compressed air
Use a clean non-abrasive cloth dampened with lens cleaning solution
Use lens tissue and lens cleaning solution on camera lenses
If surface has compound on it, first clean with alcohol, then with lens cleaning
solution
 Note: Cleaning frequency will depend on plant and process conditions.

CLEANING THE CHROMAPULSE BEAM

SPLITTER
You must remove the Beam Splitter (on some Chromapulse models) to access the bottom
side for cleaning. The method for removing the beam splitter depends on your inspection
module.
In the illustration below, item A is used in preform sidewall endcap (PSE) modules. Item
B is used in seal surface modules and some Chromapulse modules (example: CP750EV,
CP1200EV, and more).

A B

3
2
1 1

1 Beam Splitter

334 Maintenance Frequency System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 2 Screws
3 Retaining plates

To clean beam splitter:

1. Raise the camera (see "Cleaning the Camera Lens" on page 335) if necessary. Be
sure to note the camera position before moving it.
2. Loosen the screws [item 2] and carefully remove the beam splitter.
 Item A has four screws. Slide the retaining plates [item 3] to the sides and
remove the beam splitter.
 Item B has two screws. Loosen the screws to remove the beam splitter.
3. Clean the beam splitter [item 1].
 Blow off dust from beam splitter with canned, compressed air.
 Clean the glass (see "Cleaning Glass Surfaces" on page 334) on the beam
splitter.
4. Replace the beam splitter assembly.
 Item A - Replace the beam splitter with the reflective side to the outside. Slide
the retaining plates back in plates and tighten the screws.
 Item B - Replace the beam splitter with glass to the inside. Tighten the screws.

CLEANING THE CAMERA LENS

Caution
Do not touch the lens with fingers or oily cloths.

To clean the camera lens:

1. Raise the camera to access the lens by loosening the height adjustment screw. The
clamping bracket should remain in place.
2. Clean all camera lenses with lens tissue and lens cleaning fluid. Be careful not to
alter the focus or aperture of the cameras.
3. Slide the camera back into position as marked by the clamping bracket.
4. Tighten the height adjustment screw
5. Re-adjust aperture and focus if needed.
1

1 Camera height adjustment screw

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Maintenance Frequency 335
© 2011 Pressco Technology Inc. Proprietary
 2 Clamping bracket - camera height
reference

CLEANING PLASTIC SURFACES

Plastic surfaces that may require cleaning are:
Dome Light Diffuser
Ring Light Diffuser
Light Shield (if present)
Beam Splitter Diffuser (if present)
 Note: Cleaning frequency will depend on plant and process conditions.

To clean plastic surfaces:

Do Do Not
Use canned compressed air to blow away dust Do not wipe away dirt as plastic coating may be
scratched
Use a clean, non-abrasive cloth dampened with mild Do not use paper towels or paper napkins – these
soap and water solution. Saturate surface completely may scratch surfaces
to let particles wash away.
Dry the surface with clean, compressed air

CLEANING THE ELLIPSOIDAL MIRROR

This mirror provides the enhanced neck image for optimal inspection of the neck of a
can.

Warning
The special surface of the mirror can be easily scratched. Take special
precautions and do not touch the surface of the mirror.

 Note: This mirror does not require periodic cleaning. Contact Pressco Service if the
mirror has dirt or marks that cannot be blown off with clean, compressed air.
In most systems, the mirror has a built-in air cleaning system. Air is blown through the
module to keep dust and debris off the mirror and out of the module. There are no bottom
shields on these modules. You do not have to clean the mirror in these modules.

CLEANING THE PART DETECTOR

Your system will be equipped with either a part detector or proximity sensor, depending
on your application. The proximity sensor does not use a reflector. However, the
cleaning procedure for either of these types of sensors is similar.

336 Maintenance Frequency System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 The part detect sensor and reflector surfaces of the part detector must remain clean to
properly detect parts. Clean these surfaces regularly to prevent dirt and oil build-up.
To clean the part detector:
Clean the part detector surfaces with a soft, clean, lint-free cloth dampened with a
mild soap and water solution.
Clean the sensors on both sides of the conveyor.
Do not use a glass cleaning solution or strong solvent on the plastic surfaces as they
might be damaged.
 Note: The frequency of cleaning will depend on plant and process conditions.

CLEANING THE PART DETECTOR AND

REFLECTOR
The part detect sensor and reflector surfaces of the part detector must remain clean to
properly detect parts. Clean these surfaces regularly to prevent dirt and oil build-up.
Clean the part detector surfaces with a soft, clean, lint-free cloth dampened with a mild
soap and water solution. Do not use a glass cleaning solution or strong solvent on the
plastic surfaces as they might be damaged.
The frequency of cleaning will depend on plant and process conditions.

1 2
1 Part detect reflector
2 Part detect sensor

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Maintenance Frequency 337
© 2011 Pressco Technology Inc. Proprietary
 REPLACING FILTER/ REGULATOR FILTERS
The filter/ regulator assembly shown below is installed with CP4422EV inspection
modules.
1
66290
2 3

1 Filter/ regulator. No filter change necessary.

2 Filter oil coalescing
3 Filter oil vapor
Use the following part numbers and replace as indicated:

Pressco part Description Use in item Replacement frequency

number number (above)
67620 Filter element oil removal 2 Every 2000 hours

67621 Filter element oil vapor removal 3 Every 12 months

67622 Kit (contains one each of 67620 and 67621)
 You may find it easier to replace both of
these filters at the same time

338 Maintenance Frequency System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
Chapter 18
DEFECT DATABASE TOOL (OPTION)

 Note: the Defect Database tool is an optional feature. To purchase this feature,
please contact your Pressco Sales Manager. Additional hardware must be installed
by a Pressco Service Engineer. How to Contact Pressco (on page 359)
The Series V Intellispec system is capable of archiving data associated with defective
parts. The archiving of this data may be enabled or disabled. The defect data collected
includes information related to the part program, lanes, inspections, sensors and
correlated machine parts. The archive for this data is the Defect Database which is a
SQLite version 3.6 database. The purpose of Defect Database Tool is to provide a user
interface to support such activities as searching, viewing and reporting defect
information. In addition, the tool provides support for database management such as
database backup, restore, and export operations.
Note the following about the Defect Database:
Defect data from each lane is stored within a single database. That is, if you have
more than one lane, you must enable the Defect Database for each lane. A separate
database will be created for each lane.
Defect images are not stored within the database. When a database is restored, only
data is restored - not images. However, corresponding images saved by Intellispec to
the hard drive are viewable via the Image Viewer (on page 346).
To enable the Defect Database Tool:
1. Go to Lane Overview mode by clicking one of the Lane buttons.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Defect Database Tool (option) 339
© 2011 Pressco Technology Inc. Proprietary
 2. Click the Tools button , then Lane Setup, then Miscellaneous Configuration.
The Miscellaneous Configuration menu is displayed.

3. Check the Enable Defect Database box.

4. Check the Save Defect Images box if you wish to save part images along with defect
data.
To run the Defect Database Tool:

1. From Lane Overview mode, click the Favorites button.

2. Choose Defect Database from the menu. A message notifies you of a possible delay
if the database has grown large.

340 Defect Database Tool (option) System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 3. Click OK to continue. The tool opens with the Search tab displayed. These menus
are described later in this section.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Defect Database Tool (option) 341
© 2011 Pressco Technology Inc. Proprietary
 SEARCH
The Search tab provides controls for searching the database. The search results may be
limited by specific filter values. The primary filters include the Lane, Part Program,
Sensor, Inspection, Inspection Type, and Status (of inspection). Secondary filters include
machine part correlation names. A date/time range picker control is also available to
limit data by a date range.

To start the search:

1. Choose the desired filters from the available options.
2. Click the Search button. The search may take a few seconds depending on the search
criterion and the size of the database. Afterwards, the Search Results tab is
automatically selected.

Primary filters
Values for each of the primary filters may be selected from a corresponding drop-down
menu. The values within the drop-down correspond to values saved in the database for
that specific lane. For example, an inspection with data saved in the database that is
named ―Radial Edge‖ would appear in the Inspection‘s drop-down menu. The default
value for all the primary filters is ―ALL‖ meaning that all possible values for that
parameter will be included in the search results. For example, selecting ―ALL‖ for
Inspections will include defect data for all inspections for which there have been failed
inspections.

Status filters
The Status filter refers to the result status of the inspection. When "All" is selected, all
failed inspections are shown.

342 Defect Database Tool (option) System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Secondary filters
The Secondary filters are for machine parts. By default, filtering by machine part names
is disabled. To enable, select the appropriate machine part check box. A numeric spinner
will display. Pressing the up/down arrows changes the numeric value within a range from
1 to 512. Note that the machine part name displayed, in the future, will correspond to the
name configured within Intellispec; for example, if machine part 1 was named ―Cavity‖
then ―Cavity ID‖ appears adjacent to the checkbox. Presently, the machine part name
appears as a generic name such as ―Machine Part 1‖. Up to four machine parts can be
selected as secondary filters.

Date/Time Range Picker

The Date/Time range picker allows you to limit search results by a date range. By
default, the start time is set to midnight of the previous day and the end time is set to
midnight of the next day. The dates and times correspond to the standard time of
whatever timezone is used by the system. This was done to prevent reporting errors
should the system collect information during a change to or from daylight savings time.
To change start or end date:
Select the calendar icon. A calendar will display allowing you to select a desired date.

To select start or end times:

Select the appropriate drop-down and then the appropriate time. Time is presented in half
hour increments.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Defect Database Tool (option) 343
© 2011 Pressco Technology Inc. Proprietary
  Note: the start date/time must be a value prior to the end date/time. Otherwise, it is
tagged as an error and it must be corrected as shown below.

SEARCH RESULTS
After performing a search, the Search Results tab is automatically selected. Defect data
returned as search results are presented within the grid. Each row represents an
inspection associated with a defective part based on the search criteria. Each column
represents specific information about the inspection (for example, part program,
inspection name, sensor, status, time stamp, and so on). To view various columns and
rows of data for a particular page use scroll bars to the right and bottom of grid.

344 Defect Database Tool (option) System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Depending on the search criteria multiple pages of data may be returned. At the bottom
left of the grid is the page size and total records (rows) returned from the database. The
page size specifies the maximum number of rows to display per page. The page size is
set to 50 by default but may be adjusted to any desired size; the greater the page size the
fewer the pages to navigate. The bottom right of the grid is a navigation control that
allows you to navigate to various pages; it includes previous, next, jump to first page,
and jump to last page navigation.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Defect Database Tool (option) 345
© 2011 Pressco Technology Inc. Proprietary
 Image Viewer
The first column on the Search Results (on page 344) grid is the Image column which
has a View button. Selecting the View button opens the Image Viewer loaded with the
corresponding inspection name for that row. The image viewer displays the image of the
defective part if one exists; note that image capture can be enabled or disabled from the
Lane Overview user interface (see "Defect Database Tool (option)" on page 339). The
inspection associated with defective part is displayed to the right of the image. The
Image Viewer supports both pan and zoom capabilities. To zoom in, move the slider up.
To zoom out, move the slider down. To pan, drag the cursor in the image.

REPORTS
The Reports tab provides controls for generating reports based on defect data. Select the
type of report from the "Select Report" drop-down menu. Choices include:

346 Defect Database Tool (option) System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Hourly Reject Report
Detail Hourly Reject Report
Daily Reject Report.
A date/time range picker is provided to limit the report to a specific period.

Select the View Report button to display the Report Window which generates the report.
This window provides view, print, and export capabilities. Reports may be exported as:

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Defect Database Tool (option) 347
© 2011 Pressco Technology Inc. Proprietary
 Crystal Reports (*.rpt)
Adobe Acrobat (*.pdf)
Microsoft Excel (*.xls)
Microsoft Word (*.doc)
Rich Text Format (*.rtf)

348 Defect Database Tool (option) System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Hourly Reject Report
The Hourly Reject Report provides a reject trend chart which graphs inspected count and
reject count over time at hour increments. In addition, the report includes a table of data
point at hour intervals.

Detail Hourly Reject Report

The Detail Hourly Reject Report provides three trend charts:

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Defect Database Tool (option) 349
© 2011 Pressco Technology Inc. Proprietary
 Percentage of parts rejected over time
Percentage of parts rejected over part count
Number of parts rejected over time

350 Defect Database Tool (option) System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 In addition, the report includes a table of data point at hourly intervals, as shown below.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Defect Database Tool (option) 351
© 2011 Pressco Technology Inc. Proprietary
 Daily Reject Report
The Daily Reject Report provides a reject trend chart which plots the number of parts
inspected and number of parts rejected over time at daily increments. In addition, the
report includes a table of data points at daily intervals.

352 Defect Database Tool (option) System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 MAINTENANCE
The Maintenance tab provides controls for monitoring and managing the Defect
Database. The left panel contains a circular gauge that displays the percentage of
database (DB) usage. This gauge indicates what percentage of the database‘s maximum
capacity is currently in use. To the right of this gauge is status information that reflects
the current health of the Defect Database. The right panel contains a button to launch the
Database Manager and a button to launch the Defect Image Manager.

 TIP: Pressco recommends using the Trim Database (on page 356) feature, as well
as using Backup Database (on page 355) to save older data and creating a new
database. These methods put you in control of your data, and avoids delays when
you put the system online.

Circular Gauge
The needle on the database usage gauge points to the current database capacity. The
maximum database capacity is preset to a maximum of 500,000 defect outputs from
inspections. For example, when the gauge is at 20% this means that approximately
100,000 defects have been saved to the database.
Once the gauge reaches 100% then the database has exceeded its preset capacity. Once
this capacity has been exceeded then the Intellispec system automatically attempts to
trim the database at the next necessary opportunity. It will delete the oldest 80% of data
and the corresponding images; typically this occurs when you attempt to put a lane
online without performing the necessary backup and database trimming. To avoid loss of
data, a database backup (see "Backup Database" on page 355) should be performed
prior to reaching the 100% mark. It is not necessary to back up the database if there is no
desire to retain this data.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Defect Database Tool (option) 353
© 2011 Pressco Technology Inc. Proprietary
  Note: the DB Usage may exceed 100%. This means that Intellispec has not had the
opportunity to perform a trim and the artificial preset limit has been exceeded. This
can lead to significant delays in placing a lane online and possible loss of data due
to performance problems associated with dealing with a large database.

Status information
Status information, next to the circular gauge, includes:
Database (DB) Usage %
Failed Inspections - current number of defects saved to database
Maximum Failed Inspections - maximum capacity of database in terms of defect
count
Trim Factor - percent of database that will be deleted when trim performed
SQLite Status - whether it is running or stopped
Database Status - whether it is ready, stopped, detached, or there is an error
Database Version - version number of database
Last Backup - time of last backup; ―N/A‖ is displayed if a backup has never been
performed
Auto Trim Status - time of last auto trim; "N/A" is displayed if an auto trim has never
been performed
Last Trim - time of the last database trim; "N/A" is displayed if a trim has never been
performed

Database Manager
The Database Manager button from the Maintenance screen launches the Database
Manager which provides database backup, restore, export, and trim capabilities.

354 Defect Database Tool (option) System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Backup Database
The Defect Database can be backed up by selecting the Backup Database button from
within the Database Manager (on page 354). The database is saved to a directory
reserved for backups. The file type of the backup is ―.bak‖. The default name given to the
backup is the database name with a time stamp concatenated at the end, for example,
SeriesV_2009_1210_1011AM.bak. If you select the ―Clear database after backup‖
checkbox then all defect data is cleared, otherwise the Defect Database remains
unaltered.

Restore Database
The Defect Database can be restored from a previously saved backup.
To restore the database:
1. Select the Restore Database button. A dialog box opens to the location of the saved
backups.

2. Select the desired file backup (*.bak) to restore.

3. Select the Open button on the dialog box to restore the database. Be aware that
restoring the database will destroy any current defect data; however, a warning
prompt is displayed providing the opportunity to abort the process.
 Note: the Restore function can be used to restore any backups that were exported
(see "Export Database" on page 355). Use the Open Dialog Box to navigate to the
file source location.

Export Database
The Database Manager (on page 354) provides export capability to make the Defect
Database portable. The Defect Database can be exported to any local directory or
network location, including a USB drive.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Defect Database Tool (option) 355
© 2011 Pressco Technology Inc. Proprietary
 To export the database:
1. Select the Export Database button from the Database manager. A Save As dialog
box is displayed, providing the option to choose the file destination. Note that the file
type must be ".bak". The name can be any valid Windows file name.

2. Enter a name for the exported database in the File Name box.
3. Select the Save button. The database is exported.

Trim Database
The Defect Database has finite amount of storage. To maintain optimal performance, it is
trimmed when its capacity exceeds a preset threshold of 500,000 defect records. This
trim is performed automatically by the Intellispec which results in the deletion of 80% of
the defect data. Alternatively, you may manually trim the database by using the Database
Manager (on page 354).
You may see the following warning when you start the Intellispec. Trim the database as
necessary.

To manually trim the database:

Select the Trim Database button from the Database Manager (on page 354). For a large
database, this operation may take a few minutes. Note that the manual trim deletes the
oldest 10% of data. It also trims the oldest 10% of the images associated with those
database records.

Detach/ Attach Current Database

This button (in the Database Manager (on page 354)) presently does nothing due to the
nature of the SQLite database.

356 Defect Database Tool (option) System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 Defect Image Manager
Click the Defect Image Manager button from the Maintenance screen to launch the
Image Manager. This option allows you to delete images associated with database
defects. It becomes important to delete images when the disk is near or becomes full.

Click the arrow to enable deletion by date range.

Choose a lane to delete images associated with a particular lane.
Click the Delete Defect Images button to delete the selected images.
 Note: Trim Database (on page 356) also deletes images.

Refresh Database Status button

This button does nothing due to the nature of the SQLite database.

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Defect Database Tool (option) 357
© 2011 Pressco Technology Inc. Proprietary
 HELP
The Help tab provides access to technical help as well as version information for the
Defect Database Tool. The help tab has two buttons: User Manual and Online Support.
The online support is disabled if an internet connection is not available. Otherwise,
selecting the online support button opens the default browser to Pressco‘s support web
page. Selecting the user manual button opens the Intellispec user‘s manual. The user‘s
manual contains both a table of contents and index to easily locate the subject matter of
interest.

358 Defect Database Tool (option) System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
Chapter 19
HOW TO CONTACT PRESSCO

24/ 7 Customer Support:

+1 440-498-2000
E-mail:
[email protected] (mailto:[email protected]) or [email protected]
(mailto:[email protected])
Customer Service Fax:
+1 440-498-4761
Mailing Address:
Pressco Technology Inc. 29200 Aurora Rd. Cleveland, OH USA 44139-1847
Main Phone:
+1 440-498-2600
Web Site:
www.pressco.com (http://www.pressco.com)
Business Hours:
Monday - Friday, 8:00am - 5:00pm Eastern Standard Time

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) How to Contact Pressco 359
© 2011 Pressco Technology Inc. Proprietary
 C
INDEX CAMERA ADJUSTMENTS • 293, 305, 313, 318
CAMERA FOCUS AND APERTURE • 130
A CAMERA POSITION ADJUSTMENT • 294
CENTER OF MASS • 213
ABOUT THIS MANUAL • 5
CENTERLINE • 222
ABSOLUTE DIFFERENCE • 206
CHANGING YOUR PASSWORD • 47
ADAPTIVE REGION • 195
CHROMAPULSE MODULE EXTERNAL
ADAPTIVE REJECT (OPTIONAL) • 112
CONNECTIONS • 298
ADDING A USER WITH THE BIOMETRIC
CIRCULAR GAUGE • 353
LOGIN DEVICE • 48
CLEANING GLASS SURFACES • 334
ADDING REGIONS AND INSPECTIONS • 174
CLEANING OPTICAL SURFACES • 333
ADJUSTING DATE AND TIME • 119
CLEANING PLASTIC SURFACES • 336
ADJUSTING THE CP/ E SERIES MODULES •
291 CLEANING THE CAMERA LENS • 335
ADJUSTING THE CP4422EV MODULE • 305 CLEANING THE CHROMAPULSE BEAM
SPLITTER • 334
ADJUSTING THE CP500/ V MODULE • 313
CLEANING THE ELLIPSOIDAL MIRROR •
ADJUSTING THE CPX CAMERA • 317
336
ADVANCED ADJUST LIGHTING • 136
CLEANING THE PART DETECTOR • 336
ADVANCED ADJUST LIGHTING - SET
CLEANING THE PART DETECTOR AND
DELAY • 137
REFLECTOR • 337
ADVANCED ADJUST LIGHTING - ZONES •
CLEANING THE VISION PROCESSOR
137
FILTER • 332
ALARM PERCENTAGES IN TREND CHARTS
CLIPPING • 199
• 62
COLOR DISTANCE • 207
ALARMS • 11
COLOR EXTRACTION • 209
ALARMS • 75
COMMISSIONING • 27
ALARMS -- CLEARING • 76
CONTRAST • 236
AMBIENT • 232
CORRELATION • 273
ANALYSES • 231
CORRELATION DIAGNOSTICS • 109
ANGLE • 271
CP/ E MOTORIZED FOCUS CONNECTIONS
APERTURE ADJUSTMENT • 294
(OPTIONAL) • 303
ASSEMBLY, LOCATION, AND MOUNTING
CP/E INSPECTION MODULE INTERNAL
REQUIREMENTS • 25
CONNECTIONS • 299
AUTHORIZED USERS • 16
CP/E POWER PANEL CONNECTIONS • 302
AUTO LOGOUT SETUP • 56
CP/E SERIES MODULES • 290
B CP/EV MODULE MEASUREMENTS • 20
BACKUP DATABASE • 355 CP1200E LIGHT ARRAY CONNECTIONS •
BASIC ADJUST LIGHTING • 135 301
BIG LIVE IMAGE • 74 CP1200E/ CP1500E • 296
BINARY • 202 CP1500E LIGHT ARRAY CONNECTIONS •
301
BIOMETRIC DEVICE • 48
CP4422E MODULE EXTERNAL
BIOMETRIC LOGIN DEVICE (OPTIONAL) •
CONNECTIONS • 306
35

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Index 361
© 2011 Pressco Technology Inc. Proprietary
CP4422EV AUXILIARY MODULE INTERNAL ELECTRICAL CONNECTION • 26
CONNECTIONS • 312 EMPTY POCKET • 185
CP4422EV INSPECTION MODULE • 304 ENHANCEMENTS • 198
CP4422EV INTERNAL CONNECTIONS PAGE ENVIRONMENTAL CONDITIONS • 17
1 • 308
ERROR MESSAGES • 91
CP4422EV INTERNAL CONNECTIONS PAGE
EXITING THE INTELLISPEC SOFTWARE • 43
2 • 309
EXPORT A PART PROGRAM • 99
CP4422EV INTERNAL CONNECTIONS PAGE
3 • 311 EXPORT DATABASE • 355
CP500 INSPECTION MODULE • 313 EXPORTING USER ACCOUNTS • 50
CP500 INSPECTION MODULE INTERNAL EXTENDED I/O • 321
CONNECTIONS • 314 EXTENDED I/O BOARD • 321
CP500 MOTORIZED FOCUS CONNECTIONS EXTENDED I/O CIRCUITS • 326
(OPTIONAL) • 315 EXTENDED I/O CONFIGURATION • 328
CP500E LIGHT ARRAY CONNECTIONS • 300 EXTENDED I/O IN INSPECTION MODULES •
CP750E LIGHT ARRAY CONNECTIONS • 300 289, 328
CPX INSPECTION MODULE • 316 EXTENDED I/O SIGNALS • 322
CPX INTERNAL CONNECTIONS • 319 EXTENDED I/O TERMINAL BLOCK
CREATING A SUPPORT PACKAGE • 120 REFERENCE • 326

D F
DAILY REJECT REPORT • 352 FAVORITES MENU • 127
DATABASE MANAGER • 354 FEATURE • 211
DATE/TIME RANGE PICKER • 343 FILL HEIGHT • 251
DECLARATION OF CONFORMITY - FINISH LOCATION • 225
INTEGRATED TUNNEL • 22 FOCUS ADJUSTMENT • 294, 305
DECLARATION OF CONFORMITY - FORCED REJECT • 103
INTELLISPEC SYSTEM • 21
G
DEFECT DATABASE TOOL (OPTION) • 339
GAMMA CORRECTION • 203
DEFECT IMAGE MANAGER • 357
GRAPHS AND IMAGE DISPLAYS • 59
DELETE A PART PROGRAM • 98
GROW DARK AREAS • 204
DETACH/ ATTACH CURRENT DATABASE •
356 GROW LIGHT AREAS • 205
DETAIL HOURLY REJECT REPORT • 349 H
DIMENSIONS • 266 HARDWARE SETUP • 107
DISCOVERY - ACCESS AND USE • 126 HELP • 42
DISCOVERY MENU TOOLBAR • 125 HELP • 358
DISCOVERY SOFTWARE - WHAT IS HELP - REMOTE SUPPORT • 122
DISCOVERY? • 124
HOUGH • 216
DISCOVERY SOFTWARE SCREEN • 125
HOUGH VS. RADIAL EDGE • 211
DISTANCE • 266
HOURLY REJECT REPORT • 349
DISTRIBUTION • 258
HOW TO CONTACT PRESSCO • 359
DISTRIBUTION HISTOGRAM TYPES • 262
HOW TO CREATE, COPY, OR IMPORT A
E PART PROGRAM • 162
EDITING PARAMETERS • 176 HOW TO SELECT MENU ITEMS • 32

362 Index System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
 I LIGHTING ADJUSTMENTS • 295, 305, 313,
318
I/O DIAGNOSTICS • 107
LIGHTING AND IMAGING • 129
IMAGE ANALYSIS • 132
LIGHTING ZONES CP4422E • 306
IMAGE DISPLAY CONFIGURATION • 94
LIGHTING ZONES CP500 • 314
IMAGE OPTIONS • 158
LIGHTING ZONES CP500E/ CP750E • 295
IMAGE SOURCE • 139
LIGHTING ZONES CPX • 318
IMAGE VIEWER • 346
LOAD A PART PROGRAM • 98
IMAGES - LOADING • 156
LOADING IMAGES • 156
IMAGES - SAVING • 145
LOG IN MENU • 45
IMPORTING USER ACCOUNTS • 51
LOG READER • 90
INSPECTION EDITOR • 175
LOGGING IN AND LOGGING OUT • 45
INSPECTION MENU • 165
INSPECTION MODULE ADJUSTMENTS AND M
WIRING DIAGRAMS • 287 MACHINE PART CORRELATION • 95
INSPECTION OVERVIEW • 161 MACHINE PART GRAPHS • 62
INSPECTION OVERVIEW SCREEN • 41 MAINTENANCE • 353
INSPECTION TERMINOLOGY • 161 MAINTENANCE FREQUENCY • 331
INSPECTION TREE RELATIONSHIPS • 172 MANAGE PART PROGRAMS • 97
INSPECTION TYPE ICONS • 171 MANAGE SIMULATED LANE IMAGES (PDL)
INSPECTIONS • 185 • 141
INSPECTIONS GRAPH • 66 MANAGING PERMISSIONS • 52
INSTALLATION • 26 MANAGING USER ACCOUNTS • 47
INSTALLATION AND WIRING • 23 MARKING • 10
INTEGRATED TUNNEL ELECTRICAL MEASURE EXTRACT • 256
SPECIFICATIONS • 19 MEASURE ROI • 193
INTELLISPEC CABINET AND USER MEASUREMENT • 243
INTERFACE • 29
MECHANICAL KEYBOARD (MKB) • 34
INTENDED USE • 12
MENU TOOLBAR • 41
INTRODUCTION • 5
MISCELLANEOUS CONFIGURATION • 101
L MISSED PACKETS EXCEPTION • 115
LABEL SKEW EXTRACT • 263 MODULE HEIGHT ADJUSTMENT • 291
LANE ALARM CONFIGURATION • 78 MONITOR • 30
LANE ALARMS DESCRIPTION • 80 MORE LANE INFORMATION • 38
LANE DETAIL REPORT • 88 MULTIPLE TREND GRAPHS • 60
LANE OVERVIEW SCREEN • 38 N
LANE SETUP • 93
NAVIGATING THROUGH THE SYSTEM • 29
LANE SUMMARY REPORT • 87
NON-INTENDED USE • 12
LANGUAGE • 42
LIFTING HEAVY OBJECTS • 15 O
LIGHT METER • 251 OBSERVE PART IMAGE • 288
LIGHT TREE • 11 OFFLINE IMAGING • 132
LIGHT TREE • 285 ON SCREEN KEYBOARD (OSK) • 33
LIGHT TREE STATUS • 285 ONLINE / OFFLINE • 43

System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Index 363
© 2011 Pressco Technology Inc. Proprietary
OPTIONS (SENSOR MENU) • 171 REPLACING FILTER/ REGULATOR FILTERS
ORIENTATIONS • 228 • 338
REPLACING/ CLEANING THE
P CHROMAPULSE CP4422EV FAN FILTERS •
PART CHANGEOVER • 165 333
PART PRESENT DELAY CALIBRATION • 109 REPORTING • 86
PART PROGRAM CHANGE LOG • 168 REPORTS • 346
PART RATE • 92 RESIDUAL RISK • 12
PART SETUP • 91 RESTORE DATABASE • 355
PART TRACKER EXCEPTION • 115 RESULT OPTIONS • 178
PART TRACKER SIMULATION • 114 RETRO-SPEC OPTIONS • 181
PART TRACKING • 162 RETRO-SPEC PART VIEW GRAPH • 183
PART WIDTH CALIBRATION • 92 RETRO-SPEC POPULATION VIEW GRAPH •
PATTERN MATCH • 229 179
PDX CONFIGURATION • 114 REVIEW CAMERA CALIBRATION • 138
PERMISSION SETUP • 55 RIBBON REGION • 191
PERSONAL PROTECTIVE EQUIPMENT • 13 RING REGION • 187
PERSONNEL SAFETY • 13 S
POLYGON REGION • 189 SAFETY CONSIDERATIONS • 6
POWER DOWN • 276 SAFETY INFORMATION • 9
POWER UP • 275 SAVING A REGION OF INTEREST
PRESSCO PC OUTLET WIRING • 277 (UNWRAPPED) IMAGE • 156
PRIMARY FILTERS • 342 SAVING IMAGES • 144
PROTECTIVE EARTHING • 25 SAVING IMAGES THROUGH THE
RETRO-SPEC INTERFACE • 145
R
SAVING IMAGES THROUGH THE SENSOR
RADIAL EDGE • 219 MENU • 144
REBOOTING THE INTELLISPEC SYSTEM • SAVING INDIVIDUAL IMAGES WHILE
283 EDITING AN INSPECTION • 150
RECOMMENDATIONS FOR IMAGE FILE SAVING INDIVIDUAL REJECT IMAGES • 155
MANAGEMENT • 148
SAVING REJECT IMAGES • 151
RECOMMENDATIONS PRIOR TO
SAVING REJECT IMAGES BY INSPECTION •
INSTALLATION • 24
151
REFRESH DATABASE STATUS BUTTON •
SAVING REJECT IMAGES BY MACHINE
357
PART • 153
REGION EDITOR • 174
SCHEDULE REPORTS • 88
REGION OF INTEREST COMPATIBILITY
SEARCH • 342
CHART • 186
SEARCH RESULTS • 344
REGION OF INTEREST OPTIONS • 178
SECONDARY FILTERS • 343
REGIONS OF INTEREST (ROI) • 186
SELECT SENSOR IMAGES • 143
REGISTRATIONS • 211
SENSOR ALARM CONFIGURATION • 81
REJECT CONFIRM CALIBRATION • 116
SENSOR ALARMS DESCRIPTION • 83
REJECT DELAY CALIBRATION • 111
SENSOR INFORMATION • 39
REJECT IMAGES • 63
SENSOR MENU • 129
REJECTOR ENABLE/ DISABLE • 102
SENSOR MISSED STATISTICS • 90
REPLACING CAMERA • 295
364 Index System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01)
© 2011 Pressco Technology Inc. Proprietary
SENSOR OVERVIEW SCREEN • 40 TREND CHART CONFIGURATION - LANE
SEQUENCE OF EVENTS DURING OVERVIEW • 61
INSPECTION • 162 TREND CHART CONFIGURATION - SYSTEM
SERVICING THE USER INTERFACE • 277 OVERVIEW • 60
SETTING UP A PRINTER • 120 TREND GRAPHS • 59
SHAPE CHECK • 234 TRIM DATABASE • 356
SHIPPING AND HANDLING • 23 TYPOGRAPHICAL CONVENTIONS • 5
SOFTWARE UTILITIES • 119 U
SOUND PRESSURE LEVEL • 17 USB PORTS • 34
SPARE PARTS USAGE • 16 USER ACCOUNTS AND LOGIN
SPECIFICATIONS • 18 INFORMATION • 45
STABILITY OF USER INTERFACE • 27 USER INTERFACE • 18
STATIC DISCHARGE PROTECTION • 7 USER INTERFACE DISPLAY - 4 LEVELS • 35
STATISTICS CONFIGURATION • 67 USER INTERFACE ELECTRICAL
STATISTICS GRID • 67 SPECIFICATIONS • 18
STATISTICS GRID CONFIGURATION • 106 USER INTERFACE EXTERNAL
STATISTICS GRID OPTIONS • 69 CONNECTIONS • 279
STATISTICS MENU • 39 USER INTERFACE INPUT DEVICES • 31
STATUS FILTERS • 342 USER INTERFACE MEASUREMENTS • 19
STATUS INFORMATION • 354 USER INTERFACE SELECTION DEVICES • 31
STRETCH GRAYSHADES • 201 USING THE WALK BY GRAPHIC • 71
STRETCH GRAYSHADES EXAMPLE • 202 UTILITIES TO BE SUPPLIED BY CUSTOMER
• 25
SUBTRACT BIAS • 199
SWITCH SIDES • 293 V
SWITCHING USERS • 46 VENTILATION • 26
SYMBOLS • 9 VIEWING AND CLEARING ALARMS • 76
SYSTEM ALARMS • 78 W
SYSTEM BLOCK DIAGRAM - INTEGRATED
WALK BY GRAPHIC • 70
TUNNEL • 24
WALK BY SETUP • 71
SYSTEM HARDWARE INFORMATION • 275
WARNING DEVICES • 11
SYSTEM OVERVIEW SCREEN • 37
WARNINGS • 83, 181
SYSTEM SPECIFICATIONS • 17
disable inspection warnings • 101
T WIRING DIAGRAM ETHERNET SWITCHES •
TAKE SCREEN SHOT • 127 282
TEMPLATE ORIENTATION • 231 WIRING DIAGRAM TRACKBALL • 283
TEMPLATE REGISTRATION • 228 WIRING DIAGRAM USER INTERFACE/ PC •
TIMING TREND • 66 281
TOOLS MENU - LANE OVERVIEW AND WIRING DIAGRAMS • 277
SENSOR OVERVIEWS SCREENS • 86
TOOLS MENU - SYSTEM OVERVIEW
SCREEN • 85
TOOLS MENUS • 85
TOUCH SCREEN MONITOR (OPTIONAL) • 30
TRASH CAN ICON • 102
System Guide Series V Integrated Tunnel INTELLISPEC™ (69422 Rev. 01) Index 365
© 2011 Pressco Technology Inc. Proprietary