PROGRAMMABLE DC/DC CONTROLLER SC1151

FOR ADVANCED MICROPROCESSORS

March 11, 1998 TEL:805-498-2111 FAX:805-498-3804 WEB:http://www.semtech.com

DESCRIPTION FEATURES
The SC1151 voltage mode controller contains most of • 85% efficiency
the circuitry necessary to implement a DC/DC con- • 5 bit DAC for output programmability
verter for powering advanced microprocessors such • On chip power good and OVP functions
as Klamath, both in single and multiple processor con- • Designed for Intel Klamath VRM8.1 requirements
figurations.
The SC1151 features an integrated 5 bit D/A con-
verter, pulse by pulse current limiting, integrated APPLICATIONS
power good signaling, logic compatible shutdown and • Klamath microprocessor supplies
on-board over voltage protection (OVP). • Klamath VRM modules
The SC1151 operates at a fixed frequency of 200kHz, • 1.8V to 3.5V microprocessor supplies
providing an optimum compromise between size, effi- • Programmable power supplies
ciency and cost in the intended application areas.
The integrated D/A converter provides programmabil- ORDERING INFORMATION
ity of output voltage from 2.0V to 3.5V in 100mV in- (1)
crements and 1.80V to 2.05V in 50mV increments with DEVICE PACKAGE TEMP RANGE (TJ)
no external components.
SC1151CS SO-16 0° to 125°C
The SC1151 provides an OVP output which can be
used to trigger a crowbar circuit for true over voltage Note:
protection. (1) Add suffix ‘TR’ for tape and reel.

BLOCK DIAGRAM ABSOLUTE MAXIMUM RATINGS

Parameter Symbol Maximum Units
VCC CSm CSp SHUTDOWN

VCC to GND VIN -0.3 to 7 V

1.25V REF CURRENT LIMIT
VCC
70mV -
BST
+

VID4 DECODED SHUTDOWN SIGNAL

VID3 LEVEL SHIFT
D/A AND AND DRIVE
SHUTDOWN DH
VID2

VID1
LOGIC

OSCILLATOR
R

Q PGND to GND ±1 V
VID0 S
PGND

VOSENSE BST to GND -0.3 to 15 V

-
+
+
+ -

PWRGOOD
-

+
ERROR
AMP Operating TA 0 to 70 °C
VCC
-
Temperature Range
+
- Storage TSTG -65 to +150 °C
Temperature Range
OVP
A17043A
GND
Lead Temperature TLEAD 300 °C
(Soldering) 10 sec

PIN CONFIGURATION

GND 1 16 VID0

VCC 2 15 VID1
OVP 3 14 VID2

PWRGOOD 4 13 VID3

CSm 5 12 VID4

CSp 6 11 VOSENSE

PGND 7 10 SHUTDOWN

DH 8 9 BST

Pentium is a registered trademark of Intel Corporation 1

© 1998 SEMTECH CORP. 652 MITCHELL ROAD NEWBURY PARK CA

 PROGRAMMABLE DC/DC CONTROLLER SC1151
FOR ADVANCED MICROPROCESSORS

March 11, 1998

ELECTRICAL CHARACTERISTICS
Unless specified: VCC = 4.75V to 5.25V; GND = PGND = 0V; VOSENSE = VO; 0mV < (CSp-CSm) < 60mV; TA = 25oC
PARAMETER CONDITIONS VID MIN TYP MAX UNITS
43210
Output Voltage(2) IO = 2A in Application circuit 16935F 00101 1.782 1.800 1.818 V
00100 1.832 1.850 1.868
00011 1.881 1.900 1.919
00010 1.931 1.950 1.969
00001 1.980 2.000 2.020
00000 2.030 2.050 2.070
11111 1.980 2.000 2.020
11110 2.079 2.100 2.121
11101 2.178 2.200 2.222
11100 2.277 2.300 2.323
11011 2.376 2.400 2.424
11010 2.475 2.500 2.525
11001 2.574 2.600 2.626
11000 2.673 2.700 2.727
10111 2.772 2.800 2.828
10110 2.871 2.900 2.929
10101 2.970 3.000 3.030
10100 3.069 3.100 3.131
10011 3.168 3.200 3.232
10010 3.267 3.300 3.333
10001 3.366 3.400 3.434
10000 3.465 3.500 3.535
(1)
Load Regulation IO = 0.3A to 13A xxxxx 1 %
Line Regulation xxxxx 0.5 %
UV Lockout xxxxx 4.2 V
Current Limit Voltage xxxxx 60 70 80 mV
Oscillator Frequency xxxxx 180 200 220 kHz
Oscillator Max Duty Cycle xxxxx 90 95 %
DH Sink/Source Current BST - DH = 4.5V, DH - PGND = 2V xxxxx 1 A
Output Voltage Tempco xxxxx 65 ppm/oC

NOTES:
(1) Low output currents, below the continuous conduction threshold will cause an increase in output voltage beyond
the load regulation limit. For Application circuit 16935F see the regulation curve on sheet 5.
(2) All VID codes not specifically listed here are invalid and cause shutdown exactly as if the shutdown pin had been
asserted. xxxxx refers to any valid VID code.

© 1998 SEMTECH CORP. 652 MITCHELL ROAD NEWBURY PARK CA

 PROGRAMMABLE DC/DC CONTROLLER SC1151
FOR ADVANCED MICROPROCESSORS

March 11, 1998

PIN DESCRIPTION
Pin # Pin Name Pin Function
1 GND Small Signal Analog and Digital Ground
2 VCC Chip Supply Voltage
3 OVP High Signal out if VO>setpoint + 20%
(1)
4 PWRGOOD Open collector logic output, high if VO within GND 1 16 VID0
10% of setpoint VCC 2 15 VID1

5 CSm Current Sense Input (negative) OVP 3 14 VID2

PWRGOOD 4 13 VID3
6 CSp Current Sense Input (positive)
CSm 5 12 VID4
7 PGND Power Ground CSp 6 11 VOSENSE

8 DH High Side Driver Output PGND 7 10 SHUTDOWN

DH 8 9 BST
9 BST Vcc for High Side Driver
(1)
10 SHUTDOWN Logic low shuts down the converter
11 VOSENSE Top end of internal feedback chain
(1)
12 VID4 Programming Input (MSB)
(1)
13 VID3 Programming Input
(1)
14 VID2 Programming Input
(1)
15 VID1 Programming Input
(1)
16 VID0 Programming Input (LSB)

NOTE:
(1) All logic level inputs and outputs are
open collector TTL compatible

© 1998 SEMTECH CORP. 652 MITCHELL ROAD NEWBURY PARK CA

 PROGRAMMABLE DC/DC CONTROLLER SC1151
FOR ADVANCED MICROPROCESSORS

March 11, 1998

APPLICATION CIRCUIT

Q1 L1 R1 C6 C8 C10
4uH 5mOhm
BUK556 1000uF 1000uF 1000uF
5V IN VCCP

+ + + +
C3
1000uF R2 R5 D1
C1 + + PSR16C30CT
10k 10
0.1uF C2 C4
1000uF 1000uF + + +

C5 C7 C9 C12
1000uF 1000uF 1000uF 0.1uF

12V IN
R3 2.32k R4

1.00k
C11
U1 0.1uF
2 6
VCC CSp
OVP 3 5
OVP CSm
VID0 16 11
VID0 VOSENSE
VID1 15 4
VID1 PWRGOOD
VID2 14 12
VID2 VID4
VID3 13 9
VID3 BST
VID4 10 8
SHUTDOWN DH
1 7
GND PGND
SHUTDOWN
SC1151CS
PWRGD
REF 16935F

C13
0.1uF

MATERIALS LIST
Quantity Reference Part/Description Vendor Notes
4 C1,C11-C13 0.1µF Ceramic Various
9 C2-C10 1000µF/6.3V SANYO MV-GX or equiv. Low ESR
1 D1 PSR16C30CT PHOTRON
1 L1 4µH 8 Turns 16AWG on MICROMETALS T50-52D core
1 Q1 BUK556 PHILIPS Logic level FET, ≤22mΩ, 30V
1 R1 5mΩ IRC OAR-1 Series
1 R2 10kΩ, 5%, 1/8W Various
1 R3 2.32kΩ, 1%, 1/8W Various
1 R4 1kΩ, 1%, 1/8W Various
1 R5 10Ω, 5%, 1/8W Various
1 U1 SC1151CS SEMTECH

© 1998 SEMTECH CORP. 652 MITCHELL ROAD NEWBURY PARK CA

 PROGRAMMABLE DC/DC CONTROLLER SC1151
FOR ADVANCED MICROPROCESSORS

March 11, 1998

CHARACTERISTIC CURVES
SC1151 Efficiency in Application circuit 16935F Application circuit 16935F Ripple, 3.1V, 10A out

100.0%

95.0%

90.0% 3.50V Set

3.00V Set
Efficiency

85.0%
2.40V Set

80.0% 2.00V Set

75.0%

70.0%
0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0

Output Current (Amps)

Application circuit 16935F Transient Response, 3.1V, 0.3A to 10A SC1151 Regulation in Application circuit 16935F

0.050

0.040
Voltage change (V) normalized at Io=2A

Vo at Io=300mA steady state

0.030

0.020

0.010

0.000

-0.010
Vo at Io=10A steady state Steady state voltage
levels are superimposed
for reference. -0.020
0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0

Output Current (Amps)

© 1998 SEMTECH CORP. 652 MITCHELL ROAD NEWBURY PARK CA

 PROGRAMMABLE DC/DC CONTROLLER SC1151
FOR ADVANCED MICROPROCESSORS

March 11, 1998

OUTLINE DRAWING SO-16

LAND PATTERN SO-16

© 1998 SEMTECH CORP. 652 MITCHELL ROAD NEWBURY PARK CA