STRUCTURAL DESIGN

CALCULATION REPORT
Owner Name: SERAFIN RAMIREZ SR.
Location Address: Gerthel Beach compound. Brgy Fabrica, Lobo,
Batangas
Project Name: PROPOSED RESTHOUSE RESIDENCE

TABLE OF CONTENTS
1 DESIGN CRITERIA 2
1.1 Codes, References and Standards 2
1.2 Materials 2
1.2.1 Reinforced Concrete 2
1.2.2 Structural Steel 2
1.3 Design Loads 2
1.3.1 Gravity Loads 2
1.3.2 Lateral Forces 3
1.3.3 Other Additional Design Loads and Forces 4
1.4 Loading Combinations 4
1.5 Minimum Design Requirements 4
1.5.1 Reinforced Concrete 4
1.5.2 Structural Steel 4
1.6 Foundation Design Parameters 5
1.6.1 Soil Pressure 5
1.6.2 Settlement 5
1.7 Units of Measurement and Language 5
2 DESIGN CALCULATION REPORT 5
2.1 General Overview of the Building Structure 5
2.2 Basis of Analysis 5
2.3 Scope of Work 5
2.4 Structural Analysis 6
2.4.1 Analysis of the Building Model 6
2.4.2 Structural System and Configuration 6
3 DESIGN COMPUTATIONS 7
3.1 Structure Model and Geometry 7
3.2 Output of Structural Analysis and Design using STAADPro 8
3.3 Footing Design 27
4 CERTIFICATION 28

SERAFIN RAMIREZ SR._STRUCTURAL DESIGN CALCULATION REPORT

Proposed Resthouse, Gerthel Beach compound. Brgy Fabrica, Lobo, Batangas
-
1 DESIGN CRITERIA
The following is the DESIGN CRITERIA considered in the Structural Analysis and
Design of the PROPOSED RESTHOUSE DUPLEX APARTMENT to be located in
EMERALD ST., ORO VISTA SUBDIVISION, MAYAMOT, - CITY.
1.1 Codes, References and Standards
The requirements contained in the latest edition of the following codes and
standards shall form a part of these CRITERIA, in the manner and to the Extent
specified herein.
The following codes will govern the structural analysis and design:
 NSCP C101-01 National Structural Code of the Philippines Vol. 1, 6th Edition,
2009
 AISC Manual of Steel Construction, “Specification for Design, Fabrication
and Erection of Structural Steel”, 9th Edition, 1989
 ACI American Concrete Institute ACI-318 (as adopted in the NSCP 2001)
“Building Code Requirements for Concrete Works”
 AWS D1.1-1992 American Welding Society, “Welding Design and
Procedures”
 NBCP “National Building Code of the Philippines”
 IBC “International Building Code” 2006
The following standards will govern the materials of construction:
 ASTM American Society for Testing and Materials
 PNS Philippine National Standard
1.2 Materials
Materials considered in the proposed construction shall be as follows:
1.2.1 Reinforced Concrete
 Concrete Compression Strength: Concrete cylinder compression strength
measured in accordance with ASTM C-39-86 will be:
Columns, beams or girders, suspended slabs:
f’c = 20.70 MPa, minimum value unless noted otherwise
 Reinforcing Steel for Concrete
Reinforcing bars Yield Strength: Reinforcement bars minimum specified yield
strength measured in accordance with ASTM A615 will be:
Columns, beams or girders, suspended slabs:
fy = 275 MPa for Ø20 deformed bars and smaller, unless noted otherwise
fy = 414 MPa for Ø25 deformed bars and larger, unless noted otherwise
Ties, Stirrups:
fy = 275 MPa for Ø12 deformed bars and smaller, unless noted otherwise
1.2.2 Structural Steel
 Structural steel shall have minimum specified yield strength of 250 MPa for
W, H, I, S, C and L-shaped sections.
Structural steel shall have minimum specified yield strength of 170 MPa for coldformed
light gage section up to 3 mm thick and 245 MPa for cold-formed
section from 4 mm thick and larger.
 Bolts and Anchorages
Holding-down bolts for anchoring on reinforced concrete member shall be
specified as conforming to ASTM A325 or JIS Gr. 5.8.
Holding-down bolts for anchoring on metal material shall be specified as
conforming to ASTM A325 or JIS Gr. 8.8.
Holding-down bolts for anchoring on existing concrete surface shall be
specified HILTI HAS rod with appropriate HVU adhesive conforming to ASTM
A325 or JIS Gr. 5.8.
Bolts for structural steel connections shall conform to ASTM A325 or JIS Gr. 8.8.
 Welding and Galvanization
Welding Electrodes shall be of class E70xx.
Hot-dipped galvanization shall be 85 microns.
1.3 Design Loads
SERAFIN RAMIREZ SR._STRUCTURAL DESIGN CALCULATION REPORT
Proposed Resthouse, Gerthel Beach compound. Brgy Fabrica, Lobo, Batangas
-
The following loads shall be considered in this report:
1.3.1 Gravity Loads
 Dead Load, D. Dead Load means the weight of the structure itself.
Unit weights of major construction materials shall be as follows:
 Reinforced Concrete 24.00 kN/m³
 Plain Concrete 20.00 kN/m³
 Structural Steel 77.00 kN/m³
Unit weights other than the above shall conform to National Structural Code of
the Philippines (NSCP C101-01).
The following minimum dead loads may be considered in the analysis and
design of the building structure:
 Floor finishes 1.08 kN/m²
 Electrical/mechanical 0.14 kN/m²
 Live Load, L. Live Load means the load not permanently fixed to the
structure.
 Roof 1.00 kN/m²
 Residential 1.90 kN/m²
1.3.2 Lateral Forces
 Wind Load, W. Wind Load shall be calculated in accordance with the
static analytical method.
The horizontal force (F) applied to the attached structure shall be
calculated from the equation:
where,
KZ = exposure coefficient evaluated at height ‘z’
based on Table 207-3, NSCP C101-01,
KZT = a coefficient depending on the topography of
the site, taken as equal to 1.00 in this report.
Iw = Importance factor, may be taken as equal to 1.00
z = height above ground level
v = wind speed whose value may be taken as
= 200 kph in Zone II
G = gust response factor, taken as equal to 0.80 for
exposures A and B per Section 207.6.1 NSCP C101-
01
AF = projected area of structural components in one
face
CF = structure force coefficient; which can be
determined by the following expressions: Table
207-10 NSCP C101-01
AF = projected area normal to wind.
 Earthquake Load, E. Earthquake or seismic load may be considered
as lateral forces that shall act non-concurrently in the direction of
each principal axis of the structure. These loads are actually dynamic
forces that shall be used, among which, for structures 60m or more in
height. However, an alternative static lateral force is recommended
based on rational analysis of well-established principles of mechanic.
Seismic load shall be calculated in accordance with the formula as
given in Section 208 of NSCP C101-01 and using internationally
accepted structural engineering software.
Design Base Shear. The total design base shear in a given direction
shall be determined from the following equation:
The total design base shear need not exceed the following equation:
The total design base shear shall not be less than the following
equation:
In addition, for structure situated in seismic Zone 4, the total base
shear shall not be less than the following equation:
where:
I = seismic occupancy importance factor, taken as equal to 1.15 for
telecommunication tower
Ca = seismic coefficient per Table 208-4
Cv = seismic coefficient per Table 208-5
Na = near source factor per Table 208-7, taken as equal to 1.20
Nv = near source factor per Table 208-8, taken as equal to 1.60
Z = seismic zone factor taken as equal to 0.40 except for location in
Palawan
SD = soil profile type factor, taken as D
R = horizontal force factor depending on the type of structural system;
in this case, the value shall be taken as equal to 8.50 for reinforced
concrete structure.
zHFfF  q G C A in [kN]
q 47.3x10 K K v 2 I
Z ZT
6
z
  in [kN/m2]
W
RT
CI
V  v in [kN]
W
R
2.5C I
V  a in [kN]
V 0.11C IW a  in [kN]
W
R
0.8ZN I
V  v in [kN]
T = fundament structure period, seconds
1.3.3 Other Additional Design Loads and Forces
1.4 Loading Combinations
All structural members and components shall be analyzed and evaluated for
the following load combinations, whichever produces the greater stress. It is
not necessary to consider combination of load, as may be applicable, which is
obvious to produce fewer stresses than other combination of loads.
The following load combinations shall be used for member check during its
service load condition.
Load Factor
Dead, D 1.0 1.0 1.0 1.0 1.0 0.9
Live, L 1.0 0.75 0.75
Wind, W 0.75 1.0
Earthquake,
E 0.536 0.714 ±0.714
The following load combinations shall be used for concrete member check
during its limit state condition.
Load Factor
Dead, D 1.4 1.2 1.2 0.9
Live, L 1.6 1.0
Wind, W
Earthquake, 1.0 1.0
E
1.5 Minimum Design Requirements
1.5.1 Reinforced Concrete
 Minimum Dimensions of reinforced concrete members may be considered as
follows:
 Column / Pedestal Width = 200 mm
 Beam/Girder Width = 200 mm
 Foundation Thickness = 250 mm
 Minimum Reinforcement. Cracking width requirements shall be complied with and
all other minimum requirements as may deem to be applicable to the structure.
 Shrinkage and temperature requirements, As = 0.0020 BH
 Columns / Pedestals, As = 0.010 BH
 Beams, end and midspan reinforcement, As = 1.4/fy BH
 Corrosion Protection.
 To all foundation structures (isolated footing and slab foundation), a 75-mm clear
concrete cover shall be used.
 To all tie beams, a 50-mm clear concrete cover shall be used.
1.5.2 Structural Steel
All structural steel members and framing system shall comply with all applicable
code requirements.
 Minimum Thickness. Regardless of the stresses of the member, a minimum thickness
of 3.50-mm of a member plus 1.00-mm allowance for corrosion shall be used. A
total of 4.50-mm thickness shall be required.
 Slenderness Ratio, L/r
 Main Members: 200 for both axial tension and compression members
 Secondary Members: 240 for both axial tension and compression members
 Joint Strength. For a two-dimensional and three-dimensional truss framing system the
full strength of the members at the joint shall be used, except for members whose full
strength over its actual stress is greater than 1.50. On this case, the actual strength
shall be used.
 Welded Connections. Full weld connections to all joints with its corresponding joint
strength requirements.
Date: April 1, 2016
1.6 Foundation Design Parameters
1.6.1 Soil Pressure
In this report, the building foundation system will comprise of isolated footing
since the allowable net bearing capacity is 140.0-kPa at 1.50-m below the
existing natural ground level.
1.6.2 Settlement
Differential settlement of foundation shall be based on the geotechnical report.
However, in the absence of such data, a 25.0-mm differential settlement shall
be considered.
1.7 Units of Measurement and Language
All units of measurement for design work, drawings and calculations shall be in
the Metric System, unless otherwise noted.
All drawings, calculation sheets, and documents shall be written in English.

2 DESIGN CALCULATION REPORT

2.1 General Overview of the Building Structure
This CALCULATION REPORT covers the Structural Design Analysis and
Calculations and Technical Specifications for the PROPOSED RESTHOUSE
Gerthel Beach compound. Brgy Fabrica, Lobo, Batangas

The building will be a reinforced concrete structure.

2.2 Basis of Analysis
The building structure is considered to be under Type 1 construction, on which
the design is associated with the member joint strength. The provisions of the
National Structural Code of the Philippines, Volume 1, 5th Edition are basically
used in checking the stability and sufficiency of the structural members,
designed to sustain the dead load, live load, wind and seismic forces as herein
described. The design and analysis of the building structure is generated using
the internally accepted structural engineering software from reputable
developers. It is used to generate the 3D model, create all input specifications
and all output reports and displays graphical environment. These structural
modelling and analysis input specifications are stored in a text file with
extension .STD for STAADPro or .EDB for ETABS which can be analyzed and
designed. The results can be viewed graphically. The STD or EDB file is processed
by the STAAD or ETABS analysis, respectively, to produce results that are stored
in several files with extensions such as ANL or FRM, respectively. The .ANL or .FRM
text file contains the printable output as created by the specifications. The
other files contain the results (node displacements, member / element forces,
mode shapes, section forces, section moments and section displacements,
etc.).
2.3 Scope of Work
The scope of work that is performed in order to present this CALCULATION
REPORT is based on the general scope of work required, as follows:
 Preparation of detailed design drawings containing all information to
serve as primary construction drawings. The detailed design drawings
comprise of structure outline drawings and reinforcement drawings for
works.
 Structural Framing System based on the latest available applicable
codes.
 Foundation design.
 Effect of lateral loads to the proposed building.
 All structural members, beams, columns, slabs, walls, etc.
 Preparation of Final Design Report with Technical Specifications, Bills of
Quantities and Budgetary Cost Estimate for Structural Works

2.4 Structural Analysis

2.4.1 Analysis of the Building Model
Generally, the building structural modelling shall be analyzed based on the
principle of limit state design concept. However, in this report, the limit state
conditions will be limited to strength and displacement requirements.
Methodology. A comprehensive limit state design approach will be used.
Factored load combinations will consider cases where continuously acting
loads are both disadvantageous and advantageous, with load factors
adjusted as appropriate.
Where appropriate, the following computer program may be employed:
 MidasGen - Two-dimensional / three- dimensional finite element
analysis
 STAADPro 2007 - Two-dimensional / three- dimensional finite element
analysis
 PCACOL – Analysis/design of reinforced concrete column member in
accordance with ACI 318.
 GEAR2003 – General Engineering Assistance and Reference software
for routine design work.
 Customized spreadsheet programs developed by the designer in
conformity with the requirements of the applicable code.
The analysis of the structure will follow standard rational code procedures.
2.4.2 Structural System and Configuration
The building structure shall be analyzed as a three-dimensional space frame
subjected to both gravity loads and primarily for horizontal loads in accordance
with the applicable code of practice.
The proposed structure will be made of reinforced concrete building frame
system composed of ordinary braced members.

3 DESIGN COMPUTATIONS
3.1 Structure Model and Geometry
As a summary and the intended objective of this report, the following STAADPro output shows the analysis and design of the structural members
of the building structure
and their respective behaviour for the design actions.
SERAFIN RAMIREZ SR.STRUCTURAL DESIGN CALCULATION REPORT
PROPOSED RESTHOUSE
Date: April 1, 2016
3.2 Output of Structural Analysis and Design using STAADPro
PAGE NO. 1
1. STAAD SPACE
INPUT FILE: 2 STOREY rev0.STD
2. START JOB INFORMATION
3. ENGINEER DATE 9-AUG-14
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER KN
7. JOINT COORDINATES
8. 1 0 0 0; 2 4.7 0 0; 6 4.7 0 2.8; 7 8.9 0 2.8; 8 14.3 0 2.8; 9 0 0 4.25
9. 10 4.7 0 4.25; 13 0 0 6.8; 14 4.7 0 6.8; 16 14.3 0 6.8; 17 0 0 11.05
10. 18 4.7 0 11.05; 19 8.9 0 11.05; 20 14.3 0 11.05; 29 7.9 0 11.05; 30 7.9 0 6.8
11. 34 10.5 0 6.8; 35 0 -3 0; 36 4.7 -3 0; 37 4.7 -3 2.8; 38 8.9 -3 2.8
12. 39 14.3 -3 2.8; 40 0 -3 4.25; 41 4.7 -3 6.8; 42 14.3 -3 6.8; 43 0 -3 11.05
13. 44 4.7 -3 11.05; 45 8.9 -3 11.05; 46 14.3 -3 11.05; 51 7.9 -3 6.8
14. 54 8.9 0 6.8; 55 10.5 0 11.05; 57 0 3 0; 58 4.7 3 0; 59 0 3 4.25; 60 4.7 3
2.8
15. 61 8.9 3 2.8; 62 8.9 3 6.8; 63 14.3 3 2.8; 64 14.3 3 6.8; 65 4.7 3 4.25
16. 66 0 3 6.8; 67 4.7 3 6.8; 68 7.9 3 6.8; 69 7.9 3 11.05; 70 0 3 11.05
17. 71 4.7 3 11.05; 76 8.9 3 11.05; 77 14.3 3 11.05; 81 10.5 3 6.8
18. 82 10.5 3 11.05
19. MEMBER INCIDENCES
20. 101 1 35; 102 9 40; 103 17 43; 104 57 1; 105 59 9; 106 70 17; 107 2 36
21. 108 6 37; 109 14 41; 110 18 44; 111 58 2; 112 60 6; 113 67 14; 114 71 18
22. 115 30 51; 116 68 30; 117 7 38; 118 19 45; 119 61 7; 120 76 19; 121 8 39
23. 122 16 42; 123 20 46; 124 63 8; 125 64 16; 126 77 20; 1001 1 9; 1002 9 13
24. 1003 13 17; 1004 1 2; 1005 9 10; 1006 13 14; 1007 17 18; 1008 2 6; 1009 6 10
25. 1010 10 14; 1011 14 18; 1012 14 30; 1013 18 29; 1014 6 7; 1015 30 29
26. 1016 30 54; 1017 29 19; 1018 7 54; 1019 54 34; 1020 19 55; 1021 55 34
27. 1022 7 8; 1023 34 16; 1024 55 20; 1025 8 16; 1026 16 20; 2001 57 59
28. 2002 59 66; 2003 66 70; 2004 57 58; 2005 59 65; 2006 66 67; 2007 70 71
29. 2008 58 60; 2009 60 65; 2010 65 67; 2011 67 71; 2012 67 68; 2013 71 69
30. 2014 60 61; 2015 68 69; 2016 68 62; 2017 69 76; 2018 61 62; 2019 62 81
31. 2020 76 82; 2021 82 81; 2022 61 63; 2023 81 64; 2024 82 77; 2025 63 64
32. 2026 64 77
33. ELEMENT INCIDENCES SHELL
34. 1 1 2 10 9; 2 14 30 29 18; 3 6 7 54 14; 4 30 34 55 29; 7 7 8 16 54
35. 8 34 16 20 55
36. ELEMENT PROPERTY
37. 1 TO 4 7 8 THICKNESS 0.1
38. DEFINE MATERIAL START
39. ISOTROPIC CONCRETE
40. E 2.17185E+007
STAAD SPACE -- PAGE NO. 2
41. POISSON 0.17
42. DENSITY 23.5616
43. ALPHA 1E-005
44. DAMP 0.05
45. END DEFINE MATERIAL
46. MEMBER PROPERTY AMERICAN
47. 101 TO 126 PRIS YD 0.2 ZD 0.4
48. 1001 TO 1026 PRIS YD 0.4 ZD 0.2
49. 2001 TO 2026 PRIS YD 0.35 ZD 0.2
50. CONSTANTS
51. MATERIAL CONCRETE ALL
52. SUPPORTS
53. 35 TO 46 51 FIXED
54. DEFINE UBC LOAD
55. ZONE 0.4 I 1 RWX 8.5 RWZ 8.5 STYP 4 NA 1.2 NV 1.6
56. SELFWEIGHT 1
57. ***********************************
58. LOAD 1 EQ X-DIR
59. UBC LOAD X 1
60. PERFORM ANALYSIS
_
P R O B L E M S T A T I S T I C S
-----------------------------------
NUMBER OF JOINTS/MEMBER+ELEMENTS/SUPPORTS = 51/ 84/ 13
SOLVER USED IS THE IN-CORE ADVANCED SOLVER
TOTAL PRIMARY LOAD CASES = 1, TOTAL DEGREES OF FREEDOM = 228
_
***********************************************************
* *
* X DIRECTION : Ta = 0.187 Tb = 0.332 Tuser = 0.000 *
* T = 0.187, LOAD FACTOR = 1.000 *
* UBC TYPE = 97 *
* UBC FACTOR V = 0.1553 x 700.37 = 108.76 KN *
* *
***********************************************************
61. CHANGE
62. ***********************************
63. LOAD 2 EQ Z-DIR
STAAD SPACE -- PAGE NO. 3
64. UBC LOAD Z 1
65. PERFORM ANALYSIS
***********************************************************
* *
* Z DIRECTION : Ta = 0.187 Tb = 0.208 Tuser = 0.000 *
* T = 0.208, LOAD FACTOR = 1.000 *
* UBC TYPE = 97 *
* UBC FACTOR V = 0.1553 x 700.37 = 108.76 KN *
* *
***********************************************************
66. CHANGE
67. ***********************************
68. LOAD 3 DEAD LOAD
69. SELFWEIGHT Y -1
70. FLOOR LOAD
71. YRANGE 0 0 FLOAD -1.32 GY

**WARNING** about Floor/OneWay Loads/Weights.

Please note that depending on the shape of the floor you may
have to break up the FLOOR/ONEWAY LOAD into multiple commands.
For details please refer to Technical Reference Manual
Section 5.32.4 Note 6.
72. YRANGE 3 3 FLOAD -0.24 GY
73. ***********************************
74. LOAD 4 LIVE LOAD
75. FLOOR LOAD
76. YRANGE 0 0 FLOAD -1.9 GY
77. YRANGE 3 3 FLOAD -1 GY
78. ***********************************
79. * LOAD COMB
80. LOAD COMB 101 1.4DL
81. 3 1.4
82. LOAD COMB 102 1.2D+1.6L+0.5L
83. 3 1.2 4 1.6 4 0.5
84. LOAD COMB 103 1.2D+1.6L+L
85. 3 1.2 4 1.6 4 1.0
86. LOAD COMB 104 1.2DL+0.5L
87. 3 1.2 4 0.5
88. LOAD COMB 105 1.2D+L+E + X
STAAD SPACE -- PAGE NO. 4
89. 3 1.2 4 1.0 1 1.0
90. LOAD COMB 106 1.2D+L+E + Z
91. 3 1.2 4 1.0 2 1.0
92. LOAD COMB 107 1.2D+L-E - X
93. 3 1.2 4 1.0 1 -1.0
94. LOAD COMB 108 1.2D+L-E - Z
95. 3 1.2 4 1.0 2 -1.0
96. LOAD COMB 109 0.9D+E + X
97. 3 0.9 1 1.0
98. LOAD COMB 110 0.9D+E + Z
99. 3 0.9 2 1.0
100. LOAD COMB 111 0.9D-E - X
101. 3 0.9 1 -1.0
102. LOAD COMB 112 0.9D-E - Z
103. 3 0.9 2 -1.0
104. *
105. PERFORM ANALYSIS
106. LOAD LIST 101 TO 111
107. START CONCRETE DESIGN
STAAD SPACE -- PAGE NO. 5
_ CONCRETE DESIGN_
108. CODE ACI
109. NSECTION 12 ALL
110. EFACE 0.025 ALL
111. CLB 0.025 ALL
112. CLS 0.025 ALL
113. CLT 0.025 ALL
114. FC 20700 ALL
115. TRACK 1 ALL
116. FYMAIN 275790 ALL
117. FYSEC 275790 ALL
118. UNIT MMS KN
119. MAXMAIN 16 ALL
120. MINMAIN 16 ALL
121. MINSEC 10 ALL
122. *
123. UNIT METER KN
124. DESIGN COLUMN 101 TO 110
STAAD SPACE -- PAGE NO. 6
_
====================================================================
COLUMN NO. 101 DESIGN PER ACI 318-05 - AXIAL + BENDING
_
FY - 275.8 FC - 20.7 MPA, RECT SIZE - 400.0 X 200.0 MMS, TIED
ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 800.0 SQ. MM
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
----------------------------------------------------------
4 - 16 MM 1.005 101 END 0.650
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 10 SPACING 200.00 MM
COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1615.25 1292.20 677.31 49.55 73.2
M0 P-tens. Des.Pn Des.Mn e/h
18.29 -221.81 96.49 2.08 0.00719
--------------------------------------------------------
COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1615.25 1292.20 744.93 105.91 142.2
M0 P-tens. Des.Pn Des.Mn e/h
38.91 -221.81 96.49 1.99 0.00687
--------------------------------------------------------
_
====================================================================
COLUMN NO. 102 DESIGN PER ACI 318-05 - AXIAL + BENDING
_
FY - 275.8 FC - 20.7 MPA, RECT SIZE - 400.0 X 200.0 MMS, TIED
ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 800.0 SQ. MM
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
----------------------------------------------------------
4 - 16 MM 1.005 101 END 0.650
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 10 SPACING 200.00 MM
COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)

STAAD SPACE -- PAGE NO. 7

--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1615.25 1292.20 677.31 49.55 73.2
M0 P-tens. Des.Pn Des.Mn e/h
18.29 -221.81 168.65 4.36 0.00862
--------------------------------------------------------
COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1615.25 1292.20 744.93 105.91 142.2
M0 P-tens. Des.Pn Des.Mn e/h
38.91 -221.81 168.65 5.05 0.00997
--------------------------------------------------------
_
====================================================================
COLUMN NO. 103 DESIGN PER ACI 318-05 - AXIAL + BENDING
_
FY - 275.8 FC - 20.7 MPA, RECT SIZE - 400.0 X 200.0 MMS, TIED
AREA OF STEEL REQUIRED = 856.0 SQ. MM
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
----------------------------------------------------------
8 - 16 MM 2.011 107 STA 0.650-
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 10 SPACING 200.00 MM
COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1822.91 1458.33 697.06 56.74 81.4
M0 P-tens. Des.Pn Des.Mn e/h
33.40 -443.61 113.44 21.87 0.06425
--------------------------------------------------------
COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1822.91 1458.33 783.64 123.84 158.0
M0 P-tens. Des.Pn Des.Mn e/h
75.73 -443.61 113.44 18.57 0.05458
--------------------------------------------------------
_
====================================================================
COLUMN NO. 104 DESIGN PER ACI 318-05 - AXIAL + BENDING
_
FY - 275.8 FC - 20.7 MPA, RECT SIZE - 400.0 X 200.0 MMS, TIED
ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 800.0 SQ. MM
STAAD SPACE -- PAGE NO. 8
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
----------------------------------------------------------
4 - 16 MM 1.005 101 END 0.650
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 10 SPACING 200.00 MM
COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1615.25 1292.20 677.31 49.55 73.2
M0 P-tens. Des.Pn Des.Mn e/h
18.29 -221.81 29.26 5.36 0.06104
--------------------------------------------------------
COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1615.25 1292.20 744.93 105.91 142.2
M0 P-tens. Des.Pn Des.Mn e/h
38.91 -221.81 29.26 4.75 0.05408
--------------------------------------------------------
_
====================================================================
COLUMN NO. 105 DESIGN PER ACI 318-05 - AXIAL + BENDING
_
FY - 275.8 FC - 20.7 MPA, RECT SIZE - 400.0 X 200.0 MMS, TIED
AREA OF STEEL REQUIRED = 1136.0 SQ. MM
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
----------------------------------------------------------
8 - 16 MM 2.011 103 END 0.650
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 10 SPACING 200.00 MM
COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1822.91 1458.33 697.06 56.74 81.4
M0 P-tens. Des.Pn Des.Mn e/h
33.40 -443.61 98.59 21.85 0.07388
--------------------------------------------------------
COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1822.91 1458.33 783.64 123.84 158.0

M0 P-tens. Des.Pn Des.Mn e/h

75.73 -443.61 98.59 29.08 0.09831
--------------------------------------------------------
STAAD SPACE -- PAGE NO. 9
_
====================================================================
COLUMN NO. 106 DESIGN PER ACI 318-05 - AXIAL + BENDING
_
FY - 275.8 FC - 20.7 MPA, RECT SIZE - 400.0 X 200.0 MMS, TIED
AREA OF STEEL REQUIRED = 1080.0 SQ. MM
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
----------------------------------------------------------
8 - 16 MM 2.011 103 END 0.650
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 10 SPACING 200.00 MM
COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1822.91 1458.33 697.06 56.74 81.4
M0 P-tens. Des.Pn Des.Mn e/h
33.40 -443.61 60.68 13.04 0.07165
--------------------------------------------------------
COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1822.91 1458.33 783.64 123.84 158.0
M0 P-tens. Des.Pn Des.Mn e/h
75.73 -443.61 60.68 39.74 0.21830
--------------------------------------------------------
_
====================================================================
COLUMN NO. 107 DESIGN PER ACI 318-05 - AXIAL + BENDING
_
FY - 275.8 FC - 20.7 MPA, RECT SIZE - 400.0 X 200.0 MMS, TIED
ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 800.0 SQ. MM
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
----------------------------------------------------------
4 - 16 MM 1.005 101 END 0.650
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 10 SPACING 200.00 MM
COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1615.25 1292.20 677.31 49.55 73.2
M0 P-tens. Des.Pn Des.Mn e/h
18.29 -221.81 85.35 1.69 0.00658
--------------------------------------------------------
STAAD SPACE -- PAGE NO. 10
COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1615.25 1292.20 744.93 105.91 142.2
M0 P-tens. Des.Pn Des.Mn e/h
38.91 -221.81 85.35 1.90 0.00743
--------------------------------------------------------
_
====================================================================
COLUMN NO. 108 DESIGN PER ACI 318-05 - AXIAL + BENDING
_
FY - 275.8 FC - 20.7 MPA, RECT SIZE - 400.0 X 200.0 MMS, TIED
ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 800.0 SQ. MM
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
----------------------------------------------------------
4 - 16 MM 1.005 101 END 0.650
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 10 SPACING 200.00 MM
COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1615.25 1292.20 677.31 49.55 73.2
M0 P-tens. Des.Pn Des.Mn e/h
18.29 -221.81 150.29 0.71 0.00157
--------------------------------------------------------
COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1615.25 1292.20 744.93 105.91 142.2
M0 P-tens. Des.Pn Des.Mn e/h
38.91 -221.81 150.29 1.62 0.00359
--------------------------------------------------------
_
====================================================================
COLUMN NO. 109 DESIGN PER ACI 318-05 - AXIAL + BENDING
_
FY - 275.8 FC - 20.7 MPA, RECT SIZE - 400.0 X 200.0 MMS, TIED
ONLY MINIMUM STEEL IS REQUIRED.

AREA OF STEEL REQUIRED = 800.0 SQ. MM

BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
----------------------------------------------------------
4 - 16 MM 1.005 101 END 0.650
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
STAAD SPACE -- PAGE NO. 11
TIE BAR NUMBER 10 SPACING 200.00 MM
COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1615.25 1292.20 677.31 49.55 73.2
M0 P-tens. Des.Pn Des.Mn e/h
18.29 -221.81 192.97 2.68 0.00462
--------------------------------------------------------
COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1615.25 1292.20 744.93 105.91 142.2
M0 P-tens. Des.Pn Des.Mn e/h
38.91 -221.81 192.97 3.79 0.00654
--------------------------------------------------------
_
====================================================================
COLUMN NO. 110 DESIGN PER ACI 318-05 - AXIAL + BENDING
_
FY - 275.8 FC - 20.7 MPA, RECT SIZE - 400.0 X 200.0 MMS, TIED
ONLY MINIMUM STEEL IS REQUIRED.
AREA OF STEEL REQUIRED = 800.0 SQ. MM
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
----------------------------------------------------------
4 - 16 MM 1.005 101 END 0.650
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 10 SPACING 200.00 MM
COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1615.25 1292.20 677.31 49.55 73.2
M0 P-tens. Des.Pn Des.Mn e/h
18.29 -221.81 124.25 0.35 0.00093
--------------------------------------------------------
COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
1615.25 1292.20 744.93 105.91 142.2
M0 P-tens. Des.Pn Des.Mn e/h
38.91 -221.81 124.25 4.80 0.01289
--------------------------------------------------------
********************END OF COLUMN DESIGN RESULTS********************
125. DESIGN BEAM 1001 TO 1010
STAAD SPACE -- PAGE NO. 12
_
=====================================================================
BEAM NO. 1001 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 4250. MM FY - 276. FC - 21. MPA, SIZE - 200. X 400. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 2 - 16MM 0. 3499. YES NO
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 8.22 KN-MET AT 1771.MM, LOAD 103|
| REQD STEEL= 357.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
2 357. 2 - 16MM 0. 1518. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 17.11 KN-MET AT 0.MM, LOAD 108|
| REQD STEEL= 357.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
3 357. 2 - 16MM 2201. 4250. NO YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 25.12 KN-MET AT 4250.MM, LOAD 106|
| REQD STEEL= 357.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
_
B E A M N O. 1001 D E S I G N R E S U L T S - SHEAR

_
AT START SUPPORT - Vu= 7.18 KNS Vc= 53.90 KNS Vs= 0.00 KNS
Tu= 0.39 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 101
STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 21.58 KNS Vc= 53.87 KNS Vs= 0.00 KNS
Tu= 1.06 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 103
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 179. MM C/C FOR 1745. MM
STAAD SPACE -- PAGE NO. 13
___ 1J____________________ 4250X 200X 400_____________________ 9J____
| |
||========================== ====================================||
| 2No16 H 357. 0.TO 1518 2No16 H 357.2201.TO 4250 |
| | | | | | 11*10c/c179 |
| 2No16 H 43. 0.TO 3499 | | | | | | |
||============================================================= |
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | oo | | oo | | | | oo | | oo | | oo |
| 2#16 | | 2#16 | | 2#16 | | | | 2#16 | | 2#16 | | 2#16 |
| | | | | | | | | | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | | | |
| oo | | oo | | oo | | oo | | oo | | | | |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
_
=====================================================================
BEAM NO. 1002 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 2550. MM FY - 276. FC - 21. MPA, SIZE - 200. X 400. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 3 - 16MM 713. 2550. NO YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 35.40 KN-MET AT 2550.MM, LOAD 103|
| REQD STEEL= 419.MM2, ROW=0.0059, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 57. MMS |
| REQD. DEVELOPMENT LENGTH = 492. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 42943.2 cm^4
2 357. 3 - 16MM 0. 2089. YES NO
3 325. 1 - 16MM 0. 2089. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 56.94 KN-MET AT 0.MM, LOAD 103|
| REQD STEEL= 720.MM2, ROW=0.0104, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 38. MMS |
| REQD. DEVELOPMENT LENGTH = 738. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 49690.3 cm^4
_
B E A M N O. 1002 D E S I G N R E S U L T S - SHEAR
_
STAAD SPACE -- PAGE NO. 14
AT START SUPPORT - Vu= 26.31 KNS Vc= 53.28 KNS Vs= 0.00 KNS
Tu= 2.17 KN-MET Tc= 1.5 KN-MET Ts= 2.9 KN-MET LOAD 105
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 120. MM C/C FOR 920. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.24 SQ.CM.
AT END SUPPORT - Vu= 17.14 KNS Vc= 53.28 KNS Vs= 0.00 KNS
Tu= 2.17 KN-MET Tc= 1.5 KN-MET Ts= 2.9 KN-MET LOAD 105
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 120. MM C/C FOR 895. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.24 SQ.CM.
___ 9J____________________ 2550X 200X 400_____________________ 13J____
| |
||============================================================= |
| 3No16 H 357. 0.TO 2089| | | | | | | | | |
| 9*10c/c120 | | | | | | | | | 9*10c/c120 |
| 3No16 H |43.|713.TO 2550| | | | | |
| ======================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| ooo | | ooo | | ooo | | ooo | | ooo | | | | |
| 3#16 | | 3#16 | | 3#16 | | 3#16 | | 3#16 | | | | |
| | | | | | | | | | | | | |
| | | | | 3#16 | | 3#16 | | 3#16 | | 3#16 | | 3#16 |
| | | | | ooo | | ooo | | ooo | | ooo | | ooo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
_
=====================================================================
BEAM NO. 1003 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 4250. MM FY - 276. FC - 21. MPA, SIZE - 200. X 400. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 2 - 16MM 0. 3535. YES NO
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 33.81 KN-MET AT 354.MM, LOAD 103|
| REQD STEEL= 399.MM2, ROW=0.0056, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
2 357. 3 - 16MM 1846. 4250. NO YES
STAAD SPACE -- PAGE NO. 15
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 46.58 KN-MET AT 4250.MM, LOAD 103|
| REQD STEEL= 560.MM2, ROW=0.0078, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 57. MMS |
| REQD. DEVELOPMENT LENGTH = 492. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 42943.2 cm^4
_
B E A M N O. 1003 D E S I G N R E S U L T S - SHEAR
_
AT START SUPPORT - Vu= 0.13 KNS Vc= 53.30 KNS Vs= 0.00 KNS
Tu= 0.21 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 101
STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 32.96 KNS Vc= 52.73 KNS Vs= 0.00 KNS
Tu= 0.68 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 102
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 179. MM C/C FOR 1745. MM
___ 13J____________________ 4249X 200X 400_____________________ 17J____
| |
| ==========================================||
| 3No16 H 357.1846.TO 4250| | |
| | | | | | | 11*10c/c179 |
| 2No16 H 43. 0.TO 3535 | | | | | | | |
||============================================================== |
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| | | | | | | ooo | | ooo | | ooo | | ooo |
| | | | | | | 3#16 | | 3#16 | | 3#16 | | 3#16 |
| | | | | | | | | | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | | | |
| oo | | oo | | oo | | oo | | oo | | | | |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
_
=====================================================================
BEAM NO. 1004 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 4700. MM FY - 276. FC - 21. MPA, SIZE - 200. X 400. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 2 - 16MM 0. 4700. YES YES
STAAD SPACE -- PAGE NO. 16
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 19.52 KN-MET AT 2350.MM, LOAD 103|
| REQD STEEL= 357.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
2 357. 2 - 16MM 0. 1631. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 20.58 KN-MET AT 0.MM, LOAD 107|
| REQD STEEL= 357.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
3 357. 2 - 16MM 2874. 4700. NO YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 22.05 KN-MET AT 4700.MM, LOAD 105|
| REQD STEEL= 357.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
_
B E A M N O. 1004 D E S I G N R E S U L T S - SHEAR
_
AT START SUPPORT - Vu= 21.57 KNS Vc= 53.83 KNS Vs= 0.00 KNS
Tu= 0.01 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 103
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 179. MM C/C FOR 1995. MM
AT END SUPPORT - Vu= 22.66 KNS Vc= 53.83 KNS Vs= 0.00 KNS
Tu= 0.01 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 103
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 179. MM C/C FOR 1970. MM

Date: April 1, 2016

STAAD SPACE -- PAGE NO. 17
___ 1J____________________ 4700X 200X 400_____________________ 2J____
| |
||========================= =============================||
| 2No16 H 357.| 0.TO 1631| 2No16 H 357.2874.TO 4700| | |
| 13*10c/c179 | | | | | | | | | | 13*10c/c179 | |
| 2No16 H 43.| 0.TO 4700| | | | | | | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | oo | | oo | | | | oo | | oo | | oo |
| 2#16 | | 2#16 | | 2#16 | | | | 2#16 | | 2#16 | | 2#16 |
| | | | | | | | | | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
_
=====================================================================
BEAM NO. 1005 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 4700. MM FY - 276. FC - 21. MPA, SIZE - 200. X 400. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 3 - 16MM 0. 4544. YES NO
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 34.31 KN-MET AT 2350.MM, LOAD 103|
| REQD STEEL= 405.MM2, ROW=0.0057, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 57. MMS |
| REQD. DEVELOPMENT LENGTH = 492. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 42943.2 cm^4
2 357. 2 - 16MM 0. 1631. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 29.52 KN-MET AT 0.MM, LOAD 103|
| REQD STEEL= 357.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
3 357. 2 - 16MM 3657. 4700. NO YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 11.47 KN-MET AT 4700.MM, LOAD 103|
| REQD STEEL= 357.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
STAAD SPACE -- PAGE NO. 18
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
_
B E A M N O. 1005 D E S I G N R E S U L T S - SHEAR
_
AT START SUPPORT - Vu= 34.88 KNS Vc= 53.88 KNS Vs= 0.00 KNS
Tu= 0.15 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 102
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 179. MM C/C FOR 1995. MM
AT END SUPPORT - Vu= 28.03 KNS Vc= 53.88 KNS Vs= 0.00 KNS
Tu= 0.15 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 102
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 179. MM C/C FOR 1970. MM
___ 9J____________________ 4700X 200X 400_____________________ 10J____
| |
||========================= ================||
| 2No16 H 357.| 0.TO 1631| 2No16 H 357.3657.TO 4700 |
| 13*10c/c179 | | | | | | 13*10c/c179 |
| 3No16 H 43.| 0.TO 4544| | | | | | |
||======================================================================== |
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | oo | | oo | | | | | | oo | | oo |
| 2#16 | | 2#16 | | 2#16 | | | | | | 2#16 | | 2#16 |
| | | | | | | | | | | | | |
| 3#16 | | 3#16 | | 3#16 | | 3#16 | | 3#16 | | 3#16 | | |
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
_
=====================================================================
BEAM NO. 1006 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 4700. MM FY - 276. FC - 21. MPA, SIZE - 200. X 400. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 2 - 16MM 0. 4261. YES NO

STAAD SPACE -- PAGE NO. 19

|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 33.46 KN-MET AT 1958.MM, LOAD 103|
| REQD STEEL= 395.MM2, ROW=0.0055, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
2 357. 2 - 16MM 0. 456. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 2.25 KN-MET AT 0.MM, LOAD 107|
| REQD STEEL= 357.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
3 357. 3 - 16MM 2874. 4700. NO YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 46.99 KN-MET AT 4700.MM, LOAD 103|
| REQD STEEL= 565.MM2, ROW=0.0079, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 57. MMS |
| REQD. DEVELOPMENT LENGTH = 492. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 42943.2 cm^4
_
B E A M N O. 1006 D E S I G N R E S U L T S - SHEAR
_
AT START SUPPORT - Vu= 22.78 KNS Vc= 53.85 KNS Vs= 0.00 KNS
Tu= 1.45 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 102
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 179. MM C/C FOR 1995. MM
AT END SUPPORT - Vu= 46.02 KNS Vc= 53.83 KNS Vs= 7.53 KNS
Tu= 1.63 KN-MET Tc= 1.5 KN-MET Ts= 2.2 KN-MET LOAD 103
STIRRUPS ARE REQUIRED FOR SHEAR AND TORSION.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 120. MM C/C FOR 1970. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 0.93 SQ.CM.
STAAD SPACE -- PAGE NO. 20
___ 13J____________________ 4700X 200X 400_____________________ 14J____
| |
||====== =============================||
| 2No16 H 357. 0.TO 456 3No16 H 357.2874.TO 4700 |
| 13*10c/c179 | | | | | | | 18*10c/c120 |
| 2No16 H 43. 0.TO 4261 | | | | | | | | | | | |
||=================================================================== |
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | | | | | | | ooo | | ooo | | ooo |
| 2#16 | | | | | | | | 3#16 | | 3#16 | | 3#16 |
| | | | | | | | | | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | |
| oo | | oo | | oo | | oo | | oo | | oo | | |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
_
=====================================================================
BEAM NO. 1007 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 4700. MM FY - 276. FC - 21. MPA, SIZE - 200. X 400. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 2 - 16MM 0. 4700. YES YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 16.88 KN-MET AT 2350.MM, LOAD 103|
| REQD STEEL= 357.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
2 357. 2 - 16MM 0. 2022. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 21.87 KN-MET AT 0.MM, LOAD 107|
| REQD STEEL= 357.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
3 357. 2 - 16MM 2874. 4700. NO YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 23.56 KN-MET AT 4700.MM, LOAD 105|
| REQD STEEL= 357.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
STAAD SPACE -- PAGE NO. 21
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
_
B E A M N O. 1007 D E S I G N R E S U L T S - SHEAR

_
AT START SUPPORT - Vu= 20.55 KNS Vc= 53.48 KNS Vs= 0.00 KNS
Tu= 0.66 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 103
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 179. MM C/C FOR 1995. MM
AT END SUPPORT - Vu= 20.95 KNS Vc= 53.54 KNS Vs= 0.00 KNS
Tu= 0.59 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 102
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 179. MM C/C FOR 1970. MM
___ 17J____________________ 4700X 200X 400_____________________ 18J____
| |
||=============================== =============================||
| 2No16 H 357.| 0.TO 2022| | | 2No16 H 357.2874.TO 4700| | |
| 13*10c/c179 | | | | | | | | | | | | 13*10c/c179 | |
| 2No16 H 43.| 0.TO 4700| | | | | | | | | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | oo | | oo | | | | oo | | oo | | oo |
| 2#16 | | 2#16 | | 2#16 | | | | 2#16 | | 2#16 | | 2#16 |
| | | | | | | | | | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
_
=====================================================================
BEAM NO. 1008 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 2800. MM FY - 276. FC - 21. MPA, SIZE - 200. X 400. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 2 - 16MM 0. 2800. YES YES
STAAD SPACE -- PAGE NO. 22
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 13.42 KN-MET AT 0.MM, LOAD 106|
| REQD STEEL= 357.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
2 357. 2 - 16MM 0. 1622. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 12.87 KN-MET AT 0.MM, LOAD 108|
| REQD STEEL= 357.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
3 357. 2 - 16MM 1061. 2800. NO YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 23.95 KN-MET AT 2800.MM, LOAD 106|
| REQD STEEL= 357.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
_
B E A M N O. 1008 D E S I G N R E S U L T S - SHEAR
_
AT START SUPPORT - Vu= 3.37 KNS Vc= 55.81 KNS Vs= 0.00 KNS
Tu= 1.59 KN-MET Tc= 1.5 KN-MET Ts= 2.1 KN-MET LOAD 103
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 120. MM C/C FOR 1045. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 0.91 SQ.CM.
AT END SUPPORT - Vu= 18.81 KNS Vc= 55.25 KNS Vs= 0.00 KNS
Tu= 1.59 KN-MET Tc= 1.5 KN-MET Ts= 2.1 KN-MET LOAD 103
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 120. MM C/C FOR 1020. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 0.91 SQ.CM.
STAAD SPACE -- PAGE NO. 23
___ 2J____________________ 2800X 200X 400_____________________ 6J____
| |
||=========================================================================||
| 2No16 H 357.| 0.TO 1622| 2No16|H 357.1061.TO 2800 | | | | | | |
| 10*10c/c120 | | | | | | | | | | | | 10*10c/c120 | |
| 2No16 H |43.| 0.TO 2800| | | | | | | | | | | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| | | | | | | | | | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
_
=====================================================================
BEAM NO. 1009 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 1450. MM FY - 276. FC - 21. MPA, SIZE - 200. X 400. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 2 - 16MM 112. 1450. NO YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 30.18 KN-MET AT 1450.MM, LOAD 103|
| REQD STEEL= 357.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
2 357. 3 - 16MM 0. 1301. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 39.36 KN-MET AT 0.MM, LOAD 103|
| REQD STEEL= 468.MM2, ROW=0.0066, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 57. MMS |
| REQD. DEVELOPMENT LENGTH = 492. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 42943.2 cm^4
_
B E A M N O. 1009 D E S I G N R E S U L T S - SHEAR
_
STAAD SPACE -- PAGE NO. 24
AT START SUPPORT - Vu= 52.33 KNS Vc= 53.64 KNS Vs= 16.13 KNS
Tu= 7.05 KN-MET Tc= 1.5 KN-MET Ts= 9.4 KN-MET LOAD 103
STIRRUPS ARE REQUIRED FOR SHEAR AND TORSION.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 120. MM C/C FOR 370. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 4.04 SQ.CM.
AT END SUPPORT - Vu= 44.00 KNS Vc= 53.64 KNS Vs= 5.02 KNS
Tu= 7.05 KN-MET Tc= 1.5 KN-MET Ts= 9.4 KN-MET LOAD 103
STIRRUPS ARE REQUIRED FOR SHEAR AND TORSION.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 120. MM C/C FOR 345. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 4.04 SQ.CM.
___ 6J____________________ 1449X 200X 400_____________________ 10J____
| |
||=================================================================== |
| 3No16 H|357. |0.TO 1301 | | | | |
| 5*10c/c120 | | | | | 4*10c/c120 |
| 2No16 H 43. 112.TO 1450| | | | |
| ======================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| ooo | | ooo | | ooo | | ooo | | ooo | | ooo | | |
| 3#16 | | 3#16 | | 3#16 | | 3#16 | | 3#16 | | 3#16 | | |
| | | | | | | | | | | | | |
| | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
_
=====================================================================
BEAM NO. 1010 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 2550. MM FY - 276. FC - 21. MPA, SIZE - 200. X 400. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 2 - 16MM 0. 2022. YES NO
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 31.46 KN-MET AT 0.MM, LOAD 103|
| REQD STEEL= 370.MM2, ROW=0.0052, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 31327.2 cm^4
2 357. 3 - 16MM 713. 2550. NO YES
STAAD SPACE -- PAGE NO. 25
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 39.18 KN-MET AT 2550.MM, LOAD 103|
| REQD STEEL= 466.MM2, ROW=0.0065, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 57. MMS |
| REQD. DEVELOPMENT LENGTH = 492. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 42943.2 cm^4
_
B E A M N O. 1010 D E S I G N R E S U L T S - SHEAR
_
AT START SUPPORT - Vu= 8.55 KNS Vc= 53.70 KNS Vs= 0.00 KNS
Tu= 0.11 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 101
STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 20.23 KNS Vc= 53.70 KNS Vs= 0.00 KNS
Tu= 0.11 KN-MET Tc= 1.5 KN-MET Ts= 0.0 KN-MET LOAD 101

NO STIRRUPS ARE REQUIRED FOR TORSION.

REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 179. MM C/C FOR 895. MM
___ 10J____________________ 2550X 200X 400_____________________ 14J____
| |
| ======================================================||
| 3No16 H 357. 713.TO 2550 | | |
| | | | | 7*10c/c179 |
| 2No16 H 43. 0.TO 2022 | | | | |
||=========================================================== |
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| | | | | ooo | | ooo | | ooo | | ooo | | ooo |
| | | | | 3#16 | | 3#16 | | 3#16 | | 3#16 | | 3#16 |
| | | | | | | | | | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | | | |
| oo | | oo | | oo | | oo | | oo | | | | |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
********************END OF BEAM DESIGN**************************
126. DESIGN BEAM 2001 TO 2010
STAAD SPACE -- PAGE NO. 26
_
=====================================================================
BEAM NO. 2001 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 4250. MM FY - 276. FC - 21. MPA, SIZE - 200. X 350. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 2 - 16MM 0. 3809. YES NO
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 4.15 KN-MET AT 1771.MM, LOAD 103|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
2 307. 2 - 16MM 0. 1413. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 9.33 KN-MET AT 0.MM, LOAD 108|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
3 307. 2 - 16MM 2306. 4250. NO YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 13.10 KN-MET AT 4250.MM, LOAD 106|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
_
B E A M N O. 2001 D E S I G N R E S U L T S - SHEAR
_
AT START SUPPORT - Vu= 4.17 KNS Vc= 49.44 KNS Vs= 0.00 KNS
Tu= 0.08 KN-MET Tc= 1.3 KN-MET Ts= 0.0 KN-MET LOAD 101
STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 5.67 KNS Vc= 46.40 KNS Vs= 0.00 KNS
Tu= 0.08 KN-MET Tc= 1.3 KN-MET Ts= 0.0 KN-MET LOAD 101
STIRRUPS ARE NOT REQUIRED.
STAAD SPACE -- PAGE NO. 27
___ 57J____________________ 4250X 200X 350_____________________ 59J____
| |
||======================== ==================================||
| 2No16 H 307. 0.TO 1413 2No16 H 307.2306.TO 4250 |
| |
| 2No16 H 43. 0.TO 3809 |
||=================================================================== |
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | oo | | | | | | oo | | oo | | oo |
| 2#16 | | 2#16 | | | | | | 2#16 | | 2#16 | | 2#16 |
| | | | | | | | | | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | |
| oo | | oo | | oo | | oo | | oo | | oo | | |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
_
=====================================================================
BEAM NO. 2002 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 2550. MM FY - 276. FC - 21. MPA, SIZE - 200. X 350. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 2 - 16MM 689. 2550. NO YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 18.98 KN-MET AT 2550.MM, LOAD 103|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
2 307. 3 - 16MM 0. 1838. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 30.57 KN-MET AT 0.MM, LOAD 103|
| REQD STEEL= 424.MM2, ROW=0.0069, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 57. MMS |
| REQD. DEVELOPMENT LENGTH = 492. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 30572.9 cm^4
_
B E A M N O. 2002 D E S I G N R E S U L T S - SHEAR
_
STAAD SPACE -- PAGE NO. 28
AT START SUPPORT - Vu= 20.94 KNS Vc= 45.90 KNS Vs= 0.00 KNS
Tu= 0.60 KN-MET Tc= 1.3 KN-MET Ts= 0.0 KN-MET LOAD 102
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 154. MM C/C FOR 970. MM
AT END SUPPORT - Vu= 6.79 KNS Vc= 46.03 KNS Vs= 0.00 KNS
Tu= 0.41 KN-MET Tc= 1.3 KN-MET Ts= 0.0 KN-MET LOAD 101
STIRRUPS ARE NOT REQUIRED.
___ 59J____________________ 2550X 200X 350_____________________ 66J____
| |
||===================================================== |
| 3No16 H 307. 0.TO 1838 | | | |
| 8*10c/c154 | | | | |
| 2No16 H 43. 689.TO 2550 |
| =======================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| ooo | | ooo | | ooo | | ooo | | ooo | | | | |
| 3#16 | | 3#16 | | 3#16 | | 3#16 | | 3#16 | | | | |
| | | | | | | | | | | | | |
| | | | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| | | | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
_
=====================================================================
BEAM NO. 2003 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 4250. MM FY - 276. FC - 21. MPA, SIZE - 200. X 350. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 2 - 16MM 0. 3101. YES NO
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 18.09 KN-MET AT 354.MM, LOAD 103|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
2 307. 2 - 16MM 1952. 4250. NO YES
STAAD SPACE -- PAGE NO. 29
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 24.59 KN-MET AT 4250.MM, LOAD 103|
| REQD STEEL= 337.MM2, ROW=0.0055, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
_
B E A M N O. 2003 D E S I G N R E S U L T S - SHEAR
_
AT START SUPPORT - Vu= 0.24 KNS Vc= 44.12 KNS Vs= 0.00 KNS
Tu= 0.05 KN-MET Tc= 1.3 KN-MET Ts= 0.0 KN-MET LOAD 101
STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 17.73 KNS Vc= 46.16 KNS Vs= 0.00 KNS
Tu= 0.34 KN-MET Tc= 1.3 KN-MET Ts= 0.0 KN-MET LOAD 102
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 154. MM C/C FOR 1795. MM
___ 66J____________________ 4249X 200X 350_____________________ 70J____
| |
| =========================================||
| 2No16 H|307.1952.TO|4250 |
| | | | | | 13*10c/c154 |
| 2No16 H 43. 0.TO 3101 | | | | | |
||====================================================== |
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| | | | | | | oo | | oo | | oo | | oo |
| | | | | | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| | | | | | | | | | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | | | |
| oo | | oo | | oo | | oo | | oo | | | | |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
_
=====================================================================
BEAM NO. 2004 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 4700. MM FY - 276. FC - 21. MPA, SIZE - 200. X 350. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 2 - 16MM 0. 4700. YES YES
STAAD SPACE -- PAGE NO. 30
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 10.33 KN-MET AT 2350.MM, LOAD 103|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
2 307. 2 - 16MM 0. 1525. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 8.76 KN-MET AT 0.MM, LOAD 107|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
3 307. 2 - 16MM 2979. 4700. NO YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 9.67 KN-MET AT 4700.MM, LOAD 105|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
_
B E A M N O. 2004 D E S I G N R E S U L T S - SHEAR
_
AT START SUPPORT - Vu= 5.51 KNS Vc= 52.53 KNS Vs= 0.00 KNS
Tu= 0.02 KN-MET Tc= 1.3 KN-MET Ts= 0.0 KN-MET LOAD 101
STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 5.70 KNS Vc= 50.57 KNS Vs= 0.00 KNS
Tu= 0.02 KN-MET Tc= 1.3 KN-MET Ts= 0.0 KN-MET LOAD 101
STIRRUPS ARE NOT REQUIRED.
___ 57J____________________ 4700X 200X 350_____________________ 58J____
| |
||======================= ===========================||
| 2No16 H 307. 0.TO 1525 2No16 H 307.2979.TO 4700 |
| |
| 2No16 H 43. 0.TO 4700 |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | oo | | | | | | oo | | oo | | oo |
| 2#16 | | 2#16 | | | | | | 2#16 | | 2#16 | | 2#16 |
| | | | | | | | | | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
STAAD SPACE -- PAGE NO. 31
_
=====================================================================
BEAM NO. 2005 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 4700. MM FY - 276. FC - 21. MPA, SIZE - 200. X 350. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 2 - 16MM 0. 4700. YES YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 17.27 KN-MET AT 2350.MM, LOAD 103|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
2 307. 2 - 16MM 0. 1525. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 14.15 KN-MET AT 0.MM, LOAD 103|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4

3 307. 2 - 16MM 3762. 4700. NO YES

|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 5.23 KN-MET AT 4700.MM, LOAD 103|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
_
B E A M N O. 2005 D E S I G N R E S U L T S - SHEAR
_
AT START SUPPORT - Vu= 19.96 KNS Vc= 48.69 KNS Vs= 0.00 KNS
Tu= 0.02 KN-MET Tc= 1.3 KN-MET Ts= 0.0 KN-MET LOAD 103
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 154. MM C/C FOR 2045. MM
AT END SUPPORT - Vu= 5.59 KNS Vc= 81.64 KNS Vs= 0.00 KNS
Tu= 0.04 KN-MET Tc= 1.3 KN-MET Ts= 0.0 KN-MET LOAD 101
STIRRUPS ARE NOT REQUIRED.
STAAD SPACE -- PAGE NO. 32
___ 59J____________________ 4700X 200X 350_____________________ 65J____
| |
||======================= ===============||
| 2No16 H 307.| 0.TO 1525 2No16 H 307.3762.TO 4700 |
| 15*10c/c154 | | | | |
| 2No16 H 43.| 0.TO 4700 |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | oo | | | | | | | | oo | | oo |
| 2#16 | | 2#16 | | | | | | | | 2#16 | | 2#16 |
| | | | | | | | | | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
_
=====================================================================
BEAM NO. 2006 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 4700. MM FY - 276. FC - 21. MPA, SIZE - 200. X 350. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 2 - 16MM 0. 4184. YES NO
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 16.51 KN-MET AT 1958.MM, LOAD 103|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
2 307. 2 - 16MM 0. 350. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 0.81 KN-MET AT 0.MM, LOAD 111|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
3 307. 2 - 16MM 2979. 4700. NO YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 23.31 KN-MET AT 4700.MM, LOAD 103|
| REQD STEEL= 319.MM2, ROW=0.0052, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
STAAD SPACE -- PAGE NO. 33
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
_
B E A M N O. 2006 D E S I G N R E S U L T S - SHEAR
_
AT START SUPPORT - Vu= 4.33 KNS Vc= 48.08 KNS Vs= 0.00 KNS
Tu= 0.46 KN-MET Tc= 1.3 KN-MET Ts= 0.0 KN-MET LOAD 101
STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 19.95 KNS Vc= 46.50 KNS Vs= 0.00 KNS
Tu= 0.88 KN-MET Tc= 1.3 KN-MET Ts= 0.0 KN-MET LOAD 102
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 154. MM C/C FOR 2020. MM
___ 66J____________________ 4700X 200X 350_____________________ 67J____
| |
||==== ===========================||
| 2No16 H 307. 0.TO 350 2No16 H|307.2979.TO 4700 |
| | | | | 15*10c/c154 |
| 2No16 H 43. 0.TO 4184 | | | | | | |
||================================================================== |
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | | | | | | | oo | | oo | | oo |
| 2#16 | | | | | | | | 2#16 | | 2#16 | | 2#16 |
| | | | | | | | | | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | |
| oo | | oo | | oo | | oo | | oo | | oo | | |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
_
=====================================================================
BEAM NO. 2007 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 4700. MM FY - 276. FC - 21. MPA, SIZE - 200. X 350. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 2 - 16MM 0. 4700. YES YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 8.79 KN-MET AT 2350.MM, LOAD 103|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
STAAD SPACE -- PAGE NO. 34
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
2 307. 2 - 16MM 0. 1525. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 9.27 KN-MET AT 0.MM, LOAD 107|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
3 307. 2 - 16MM 2979. 4700. NO YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 10.50 KN-MET AT 4700.MM, LOAD 103|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
_
B E A M N O. 2007 D E S I G N R E S U L T S - SHEAR
_
AT START SUPPORT - Vu= 5.30 KNS Vc= 49.87 KNS Vs= 0.00 KNS
Tu= 0.24 KN-MET Tc= 1.3 KN-MET Ts= 0.0 KN-MET LOAD 101
STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 5.91 KNS Vc= 47.64 KNS Vs= 0.00 KNS
Tu= 0.24 KN-MET Tc= 1.3 KN-MET Ts= 0.0 KN-MET LOAD 101
STIRRUPS ARE NOT REQUIRED.
___ 70J____________________ 4700X 200X 350_____________________ 71J____
| |
||======================= ===========================||
| 2No16 H 307. 0.TO 1525 2No16 H 307.2979.TO 4700 |
| |
| 2No16 H 43. 0.TO 4700 |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | oo | | | | | | oo | | oo | | oo |
| 2#16 | | 2#16 | | | | | | 2#16 | | 2#16 | | 2#16 |
| | | | | | | | | | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
STAAD SPACE -- PAGE NO. 35
_
=====================================================================
BEAM NO. 2008 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 2800. MM FY - 276. FC - 21. MPA, SIZE - 200. X 350. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 2 - 16MM 0. 2800. YES YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 5.16 KN-MET AT 0.MM, LOAD 110|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
2 307. 2 - 16MM 0. 1517. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 6.18 KN-MET AT 0.MM, LOAD 108|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4

BUILDING rev0 24
Date: April 1, 2016
3 307. 2 - 16MM 1166. 2800. NO YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 9.91 KN-MET AT 2800.MM, LOAD 106|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
_
B E A M N O. 2008 D E S I G N R E S U L T S - SHEAR
_
AT START SUPPORT - Vu= 1.97 KNS Vc= 81.23 KNS Vs= 0.00 KNS
Tu= 0.57 KN-MET Tc= 1.3 KN-MET Ts= 0.0 KN-MET LOAD 101
STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 3.97 KNS Vc= 47.69 KNS Vs= 0.00 KNS
Tu= 0.57 KN-MET Tc= 1.3 KN-MET Ts= 0.0 KN-MET LOAD 101
STIRRUPS ARE NOT REQUIRED.
STAAD SPACE -- PAGE NO. 36
___ 58J____________________ 2800X 200X 350_____________________ 60J____
| |
||=========================================================================||
| 2No16 H 307. 0.TO 1517 2No16 H 307.1166.TO 2800 |
| |
| 2No16 H 43. 0.TO 2800 |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| | | | | | | | | | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
_
=====================================================================
BEAM NO. 2009 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 1450. MM FY - 276. FC - 21. MPA, SIZE - 200. X 350. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 2 - 16MM 0. 1450. YES YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 12.50 KN-MET AT 1450.MM, LOAD 103|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
2 307. 2 - 16MM 0. 1196. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 16.51 KN-MET AT 0.MM, LOAD 103|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
_
B E A M N O. 2009 D E S I G N R E S U L T S - SHEAR
_
STAAD SPACE -- PAGE NO. 37
AT START SUPPORT - Vu= 22.72 KNS Vc= 48.53 KNS Vs= 0.00 KNS
Tu= 4.66 KN-MET Tc= 1.3 KN-MET Ts= 6.2 KN-MET LOAD 103
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 108. MM C/C FOR 420. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 2.81 SQ.CM.
AT END SUPPORT - Vu= 17.50 KNS Vc= 48.84 KNS Vs= 0.00 KNS
Tu= 4.66 KN-MET Tc= 1.3 KN-MET Ts= 6.2 KN-MET LOAD 103
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 108. MM C/C FOR 395. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 2.81 SQ.CM.
___ 60J____________________ 1449X 200X 350_____________________ 65J____
| |
||============================================================= |
| 2No16 H 307.| 0.TO 1196| | | | |
| 5*10c/c108 | | | | | 5*10c/c108 |
| 2No16 H 43.| 0.TO 1450| | | | |
||=========================================================================||
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| oo | | oo | | oo | | oo | | oo | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | | | |
| | | | | | | | | | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| oo | | oo | | oo | | oo | | oo | | oo | | oo |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|

=====================================================================
BEAM NO. 2010 DESIGN RESULTS - FLEXURE PER CODE ACI 318-05
LEN - 2550. MM FY - 276. FC - 21. MPA, SIZE - 200. X 350. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
_
1 43. 2 - 16MM 0. 1967. YES NO
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 12.48 KN-MET AT 0.MM, LOAD 103|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
2 307. 2 - 16MM 818. 2550. NO YES
STAAD SPACE -- PAGE NO. 38
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 17.47 KN-MET AT 2550.MM, LOAD 103|
| REQD STEEL= 307.MM2, ROW=0.0050, ROWMX=0.0279 ROWMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 457./ 41./ 114. MMS |
| REQD. DEVELOPMENT LENGTH = 350. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 22446.3 cm^4
_
B E A M N O. 2010 D E S I G N R E S U L T S - SHEAR
_
AT START SUPPORT - Vu= 1.55 KNS Vc= 44.72 KNS Vs= 0.00 KNS
Tu= 0.15 KN-MET Tc= 1.3 KN-MET Ts= 0.0 KN-MET LOAD 101
STIRRUPS ARE NOT REQUIRED.
AT END SUPPORT - Vu= 18.59 KNS Vc= 47.08 KNS Vs= 0.00 KNS
Tu= 0.57 KN-MET Tc= 1.3 KN-MET Ts= 0.0 KN-MET LOAD 103
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 154. MM C/C FOR 945. MM
___ 65J____________________ 2550X 200X 350_____________________ 67J____
| |
| ===================================================||
| 2No16 H 307. 818.TO|2550| | |
| | | | | 8*10c/c154 |
| 2No16 H 43. 0.TO 1967 | | | | |
||========================================================= |
| |
|___________________________________________________________________________|
_______ _______ _______ _______ _______ _______ _______
| | | | | | | | | | | | | |
| | | | | oo | | oo | | oo | | oo | | oo |
| | | | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 |
| | | | | | | | | | | | | |
| 2#16 | | 2#16 | | 2#16 | | 2#16 | | 2#16 | | | | |
| oo | | oo | | oo | | oo | | oo | | | | |
| | | | | | | | | | | | | |
|_______| |_______| |_______| |_______| |_______| |_______| |_______|
********************END OF BEAM DESIGN**************************
127. DESIGN ELEMENT ALL
STAAD SPACE -- PAGE NO. 39
ELEMENT DESIGN SUMMARY
----------------------
ELEMENT LONG. REINF MOM-X /LOAD TRANS. REINF MOM-Y /LOAD
(SQ.MM/MM) (KN-MM/MM) (SQ.MM/MM) (KN-MM/MM)
FY: 275.788 MPA FC: 20.700 MPA COVER: 25.000 MM TH: 100.000 MM
1 TOP : Longitudinal direction - Only minimum steel required.
1 BOTT: Longitudinal direction - Only minimum steel required.
1 TOP : Transverse direction - Only minimum steel required.
1 BOTT: Transverse direction - Only minimum steel required.
1 TOP : 0.200 0.84 / 103 0.200 0.10 / 106
BOTT: 0.200 0.00 / 0 0.200 0.12 / 108
FY: 275.788 MPA FC: 20.700 MPA COVER: 25.000 MM TH: 100.000 MM
2 TOP : Longitudinal direction - Only minimum steel required.
2 BOTT: Longitudinal direction - Only minimum steel required.
2 TOP : Transverse direction - Only minimum steel required.
2 BOTT: Transverse direction - Only minimum steel required.
2 TOP : 0.200 0.00 / 103 0.200 0.29 / 103
BOTT: 0.200 0.97 / 103 0.200 0.00 / 108
FY: 275.788 MPA FC: 20.700 MPA COVER: 25.000 MM TH: 100.000 MM
3 TOP : Longitudinal direction - Only minimum steel required.
3 BOTT: Longitudinal direction - Only minimum steel required.
3 TOP : Transverse direction - Only minimum steel required.
3 BOTT: Transverse direction - Only minimum steel required.
3 TOP : 0.200 0.00 / 103 0.200 0.14 / 106
BOTT: 0.200 1.20 / 103 0.200 0.13 / 108
FY: 275.788 MPA FC: 20.700 MPA COVER: 25.000 MM TH: 100.000 MM
4 TOP : Longitudinal direction - Only minimum steel required.
4 BOTT: Longitudinal direction - Only minimum steel required.
4 TOP : Transverse direction - Only minimum steel required.
4 BOTT: Transverse direction - Only minimum steel required.
4 TOP : 0.200 0.16 / 109 0.200 0.72 / 103
BOTT: 0.200 0.33 / 107 0.200 0.00 / 108
FY: 275.788 MPA FC: 20.700 MPA COVER: 25.000 MM TH: 100.000 MM
7 TOP : Longitudinal direction - Only minimum steel required.
7 BOTT: Longitudinal direction - Only minimum steel required.
7 TOP : Transverse direction - Only minimum steel required.

7 BOTT: Transverse direction - Only minimum steel required.

7 TOP : 0.200 1.52 / 103 0.200 0.46 / 103
BOTT: 0.200 0.00 / 107 0.200 0.00 / 108
FY: 275.788 MPA FC: 20.700 MPA COVER: 25.000 MM TH: 100.000 MM
8 TOP : Longitudinal direction - Only minimum steel required.
8 BOTT: Longitudinal direction - Only minimum steel required.
8 TOP : Transverse direction - Only minimum steel required.
8 BOTT: Transverse direction - Only minimum steel required.
8 TOP : 0.200 1.95 / 103 0.200 0.77 / 103
BOTT: 0.200 0.00 / 107 0.200 0.00 / 108
STAAD SPACE -- PAGE NO. 40
***************************END OF ELEMENT DESIGN***************************
128. END CONCRETE DESIGN
129. LOAD LIST 101 TO 104
************** END OF LATEST ANALYSIS RESULT **************
131. FINISH

BUILDING rev0 27
3.3 Footing Design
Design and Analysis of Isolated Footings
Project Information
Project = PROPOSED RESTHOUSE
Title = FOOTING DESIGN
Organization =
Footing1: Input Data
Material Properties:
Main Rebars, fy 275.0 N/mm^2
Concrete fc' 21.0 N/mm^2
Concrete Density 24.0 kN/m^2
Basic Footing Data
Column Cross-Section XSRectangle
Soil Density 18.0 kN/m^3
Soil Bearing Capacity 140.0 kN/m^2
Natural Soil Level (NSL) 0.00 m
Excavation Level (Excl) 1.20 m
Height of Overburden
Soil (Hso)
0.00 m
Geometry Data:
Length 1.20 m
Width 1.20 m
Thickness at Edge 0.30 m
Thickness at Center 0.30 m
ACECOMS GEAR: Isolated Footing Design Version: 2.1 (Rev. 5)
8/9/2014 1
Applied Loads
Sr
.
N
o.
Load
Comb
Pu (kN) Mux (kNm)
Muy (kNm)
Load
Factor
OS
Factor
1 D+L 246.45 0 0 1.45 1
Footing Diagram
Footing1
ACECOMS GEAR: Isolated Footing Design Version: 2.1 (Rev. 5)
8/9/2014 2
SERAFIN RAMIREZ SR._STRUCTURAL DESIGN CALCULATION REPORT
Proposed Resthouse, Gerthel Beach compound. Brgy Fabrica, Lobo, Batangas
-
National Structural Code of the Philippines, Vol. 1, 6th Edition for Buildings and Other Vertical
Structures. A structural analysis and design calculation using computer softwares (Section 2.4.1) is
presented in the structural design report, which forms part of this certification to affirm the structural
stability of the proposed structure.
However, any further loads applied on the building structure that are not included in the report as
reflected on the architectural design plans shall be beyond the scope and responsibility of the
undersigned.
This certification is being issued for the intended building location for whatever technical purpose it
may serve.