Warrior 1800 Illustrated Parts Catalog Revision 13

PARTS BOOK INTRODUCTION
COPYRIGHT
No copies or reproductions may be made from this manual, parts lists or illustrations without
written prior consent of TEREX®. This manual complete or in part must not be loaned to a third party.
Powerscreen is a registered trademark for portable screening plant manufactured by TEREX®.
SPARE PARTS – CONTENTS
1. GENERAL INFORMATION………………….………...…...............………………………….............................
2. SPARE PARTS ORDERING PROCEDURE……………………….................……………………....................
3. SPARE PARTS ORDER FORM………………………………...……………….................................................
4. UNDERSTANDING YOUR MACHINE SERIAL NUMBER.……………………………....................................
5. PARTS SUPPORT - GOOD PRACTISE ADVICE……………………………..................................................
6. HOW TO READ YOUR TRACK IDENTIFICATION PLATE……………………………....................................
7. WHERE TO FIND YOUR ENGINE SERIAL PLATE……………………….……..............................................
8. FINDING THE SOFTWARE VERSION OF YOUR PDM AND PLC.…………...............................................
9. MACHINE NAVIGATION.........................................……………………………................................................
10. TYPES OF SCREEN MEDIA ............................................…...………….………….....................................
11. SPEEDHARPS.............................……..…………………........................................................
12. MESH SPECS.............................……..…………………..............................................................................
13. PAINT CODES..............................................…………………………...........................................................
POWERSCREEN®
200 COALISLAND ROAD, DUNGANNON, CO.TYRONE N.IRELAND, BT71 4DR
TEL: +44(0)2887 718500
747231 or [email protected] (SALES)
- [email protected] (TECHNICAL)
- 740701 (HELPDESK)
POWERSCREEN PARTS DEPARTMENT

TEREX (GB) LTD
32 FARLOUGH ROAD, DUNGANNON, CO.TYRONE N.IRELAND, BT71 4DT
Email: [email protected] - Website www.powerscreen.com
TEREX® reserves the right to change specification without prior notice.

1. GENERAL INFORMATION
• When purchasing Spareparts customers should in their own interest, always use genuine Terex parts.
• Spare parts must comply with the technical requirements specified by the manufacturer.
• Only spare parts from the original equipment manufacturers can be relied to do so.
• Spares parts that have not been supplied by Terex cannot be relied upon for correct material, dimensions
or finish.
• Terex cannot therefore be responsible for any damage arising from use of any such parts and the
Guarantee will be invalid.
2. SPARE PARTS ORDERING PROCEDURE
Ordering Procedure
To ensure delivery of your parts, when ordering please quote:
• Machine Serial Number
• Figure Number and Item Number
• Part Number
• Part Description
• Quantity Required
EXAMPLE:
If you wanted to order 1 Conveyor Tracking Roller, place your order in the following fashion:
Machine Serial Number -

Figure Number – 02-08
Item Number - 27
Part Number - 06663100
Part Description - GEARBOX
Quantity required - 1
This information will enable us to supply the correct parts with the minimum of delay.
NOTE:
Orders for spare parts must be sent to your local dealer.
To find out whom your local dealer is please log on to www.powerscreen.com and use the Dealer Search
function.
3. SPARE PARTS ORDERING FORM

4. UNDERSTANDING YOUR MACHINE SERIAL NUMBER (SCREENER)
CHIEFTAIN 1700
2012
29400 KG
PID00129CDGC65315
PID00129CDGC65315
PID 00129 C DG C 6 5315
Powerscreen Model
Check Digit
Month Code
Plant Code
Year Code Sequence Number
SERIAL NUMBER PLATE

CAN BE FOUND HERE OR ON THE
OPPOSITE SIDE OF THIS MACHINE
5. PARTS SUPPORT - GOOD PRACTISE ADVICE
Be aware there are enquires where the parts should not be supplied without firstly obtaining the Machine
Serial Number and checking the record card. The main components to consider are:
HYDRAULIC PUMPS
Pumps vary depending on the options fitted to your machine. This is why the pumps are generally not part-
coded in the parts book.
TRACK PARTS
Terex have 3-4 Track suppliers. Each track type is illustrated in the part book. It is important to select the
parts from the correct supplier. See Section 6 Where to find your Track Identification Plate.
ENGINE PARTS
The engine fitted to your machine can vary due to the customer preference (i.e. Deutz, CAT). Alternatively
it can differ due to machine options fitted (some options require a higher spec engine) or simply a change
over time as suppliers update engines to meet emission regulations. It is therefore important to obtain the
engine serial number to order parts. This information can be obtained from the engine plate, or from the
machine record. See Section 7 Where to find your Engine Serial Plate.
ELECTRICS
Control Panels, PC Boards, Hetronic Remotes - these items are serial number dependant and will have
ther serial numbers located on the part. See Section 8 Finding the Software Version of your PDM and PLC.
6. WHERE TO FIND YOUR TRACK IDENTIFICATION PLATE
It is necessary when ordering any track spare parts, that all numbers relating to the tracks are quoted along
with your machine serial number..
The identification plate is located on the outside face of each left and right hand track. On some occasions
the Serial Number can be found stamped in the skid plate or track frame. Below is the current range of
tracks fitted to our machines.
Track Frame Skid Plate
Identification Plate Locations
Strickland Tracks Terex Tracks
Terex / Trackline Tracks

7. WHERE TO FIND YOUR ENGINE SERIAL PLATE
It is necessary when ordering any engine spare parts, that all numbers relating to the engine are quoted
along with your machine serial number..
Depending on the engine fitted, the serial plate can be found either on the left / right side of the engine and
in some cases on top. The spares department need all of these numbers in order to determine the
components that were included with the engine. This permits accurate identification of replacement part
numbers.
Above
Right Hand Side Left Hand Side
Caterpillar
Deutz
Scania
8. FINDING THE SOFTWARE VERSION OF YOUR PDM AND PLC
It is necessary when ordering a new PLC or PDM that you note all numbers relating to them, please quote
these numbers along with your machine serial number.
When you turn on the screen take note of the details from the bottom of the start up page. The identification
sticker which displays the software version is located on the outside of each the PLC and PDM.
PDM Sticker PLC Sticker

Location Location
9. MACHINE NAVIGATION
The following will help you determine your location in relation to your machine.
Please note that the Feed End is always the Back of your machine.
Screener Right Hand Side
Feed End
Front Back
Discharge
End
Left Hand Side

10. TYPES OF SCREEN MEDIA
Available in a wide range of sizes – For details please contact us.
Woven Screens Elongated Screens
Slow/Fast Screen Hardox Punch Plate
Finger Screens Bofar Bars
Ball Decks Speed Harps

10. TYPES OF SCREEN MEDIA CONTINUED
Polyurathane Modular Panels Rubber Screen Mats

11. SPEEDHARPS
To order speedharp use the following mesh part number configuration system:
SH - Speedharp
AA – Speedharp code (see table on next page for full list of speedharp codes)
BB – Speedharp aperture e.g. 3mm is 03
CCC – Wire diameter e.g. 1mm is 100, 0.66mm is 066
DD – Wire type e.g. PW is Plain Wire, SS is Stainless Steel wire
PP – Plastic Profile
If in doubt contact us for correct part number

12. MESH SPECS
To order screen mesh use the following mesh part number configuration system:
MXXYYYYZZZ
M - Mesh
XX - Mesh Code e.g. M29 is a Trommel 830 (see table below for full list of machine codes)
YYYY - Mesh aperture e.g. 100mm is 1000, 50mm is 0500
ZZZ - Wire diameter e.g. 12.5mm is 125, 4mm is 040
If in doubt contact us for correct part number

13. PAINT CODES
Powerscreen Green - RAL 5021 (RGB 26/122/99)

Table of Contents
Figure Description Page

01-01 INCLINED HOPPER AND BELT FEEDER 1
01-02 HOPPER HORIZONTAL FEEDER 5
01-03 HORIZONTAL BELT FEEDER CONVEYOR 9
01-04 APRON FEEDER CONVEYOR 13
01-05 HORIZONTAL FEEDER (RADIAL M/C) 17
01-06 INCLINED BELT FEEDER CONVEYOR 19
02-01 SCREENBOX 23
02-02 SCREENBOX TOP DECKS 27
02-03 SCREENBOX BOTTOM DECKS 31
02-04 SCREENBOX DRIVE 35
02-05 SCREENBOX WALKWAYS 39
02-05 SCREENBOX WALKWAYS 41
03-03 TAIL CONV HEAD SECT (1200mm BELT) 43
03-04 TAIL CONV TAIL SECT (1200mm BELT) 47
03-05 TAIL CONV HEAD SECT (1400mm BELT) 51
03-06 TAIL CONV TAIL SECT (1400mm BELT) 55
04-01 SIDE/FINES CONVEYOR HEAD SECTION 59
04-02 SIDE/FINES CONVEYOR MIDDLE SECTIONS 63
04-03 SIDE / FINES CONVEYOR LOWER SECTION 67
04-04 TELE SIDE CONVEYOR HEAD SECTION 71
04-05 TELESCOPIC SIDE / FINES CONV MID 75
04-06 TELESCOPIC SIDE / FINES CONV LOWER 79
05-01 COLLECTION CONVEYOR TAIL DRUM 83
05-02 COLLECTION CONVEYOR DRIVE DRUM 87
05-03 EXTENDED COLLECTION CONVEYOR LOWER 91
05-04 EXTENDED COLLECTION CONVEYOR MID 95
05-05 EXTENDED COLLECTION CONVEYOR HEAD 97
05-06 EXTENDED COLLECTION CONVEYOR 99
05-07 COLLECTION CONV (RADIAL) DRIVE DRUM 101
05-08 COLLECTION CONV (RADIAL) TAIL DRUM 105
05-09 TROUGHED COLLECTION CONVEYOR 109
06-13 DEUTZ CANOPY (TIER III) 113
06-14 HYDRAULIC TANK (TIER III) 117
06-15 VALVE BANK (TIER III) 121

06-16 DEUTZ 2013 (TIER III) 125
06-17 CAT CANOPY (TIER III) 129
06-18 CAT C4.4 83kW (TIER III) 133
06-19 QUAD PUMP COLLECTION/FINES SPLIT (TIER III) 137
06-20 DUAL POWER OPTION 139
06-21 RADIATOR CAP ACCESS 143
06-22 TIER 4i POWERUNIT CANOPY LAYOUT 145
06-22-A TIER 4i POWER UNIT ROOF 147
06-22-B TIER 4i POWER UNIT BATTERY 149
06-22-C TIER 4i OIL COOLER 151
06-22-D.1 TIER 4i POWER UNIT FRONT DOOR RHS 153
06-22-D.2 TIER 4i POWER UNIT FRONT DOOR POST 155
06-22-D.3 TIER 4i POWER UNIT DOOR FRONT LHS 157
06-22-E TIER 4i VALVE BLOCK LAYOUT 159
06-22-E.1 TIER 4i SDM140 VALVE BLOCK 1 161
06-22-E.2 TIER 4i SD14_VALVE_2 163
06-22-E.3 TIER 4i SD14_VALVE_3 165
06-22-E.4 TIER 4i SD14_VALVE_4 167
06-22-E.5 TIER 4i SD14 WITH PROXIMITY VALVE 5 169
06-22-E.6 TIER 4i SD14_VALVE_BLOCK_6 171
06-22-E.7.1 TIER 4i CV115 5 BANK 173
06-22-E.7.2 TIER 4i BALLVALVE 175
06-22-E.8.1 TIER 4i FLOW CONTROL VALVE 1 177
06-22-F TIER 4i POWER UNIT FRAME 183
06-22-G TIER 4i HYDRAULIC TANK MAIN 185
06-22-G.1 TIER 4i TRACK SOLENOIDS 189
06-22-H TIER 4i POWER UNIT BACK DOOR 191
06-23-A TIER 4i CAT 4.4 ENGINE FILTER COMPONENTS 193
06-23-B TIER 4i CAT 4.4 ENGINE EXHAUST 197
06-23-C TIER 4i CAT 4.4 ENGINE SIDE PUMP BREAKDOWN 199
06-23-D TIER 4i CAT 4.4 ENGINE QUAD PUMP 201
06-23-E TIER 4i CAT 4.4 DONALDSON AIR FILTER BREAKDOWN 203
06-24-A TIER 4i CAT 4.4 ELECTRICAL CONTROL PANEL INTERNALS 205
07-01 CHASSIS FRAME (TRACK SYS A) 207

07-01-A FUEL TANK FROM SERIAL: PID00123HDGC75391 211
07-02 CHASSIS FRAME (TRACK SYS B) 213
07-03 CHASSIS FRAME (JACK-UP SCREENBOX) 217
07-04 BOLT-ON TRACK CHASSIS 219
07-05 BOLT-ON TRACK CHASSIS 3240 221
08-01 RADIAL CONVEYOR LOWER 223
08-02 RADIAL CONVEYOR HEAD 227
09-01 TWO WAY SPLIT KIT 231
10-01 STICKER LANGUAGE KITS 233
11-01 SERVICE SPARES / CONSUMABLES 235
11-02 RECOMMENDED SPARES 2000 HOURS 237
12-01 ELECTRICAL SPARES 243
12-02 PERKINS/CATERPILLAR WIRING DIAGRAM 245
12-03 MANUAL TRACK WIRING DIAGRAM 247
12-04 FUSE & RELAY DESIGNATIONS 249
13-01 HYDRAULIC PARTS 251
13-02 HYD CIRCUIT STD 255
13-03 HYD CIRCUIT (TELE CONV) TEST POINTS 257
13-04 HYD CIRCUIT (RADIAL CONVEYOR) 259
13-05 HOSE KITS LISTINGS 261
13-06 BELT FEEDER HYD. SCH. 263
13-07 APRON FEEDER HYD. SCH. 265
13-08 BELT FEEDER C/W TELESCOPIC SIDES HYD. SCH. 267
13-09 HYD CIRCUIT FINES SPLIT 269
13-10 DUAL POWER HYDRAULIC SCHEMATIC 271

NAME: INCLINED HOPPER AND BELT FEEDER MACHINE: WARRIOR 1800
ILLUSTRATION: FEEDER
FIGURE: 01-01 REV: A
Page 1
Item Part No Rev Description Qty
1 12330150 0 FEEDER MTG FRAME 1
2 12230270 0 CONVEYOR BACK GUARD 1
3 12230148 0 HOPPER BACK MTG 1
4 12230141 0 HOPPER SIDE LH 1
5 12230144 0 HOPPER SIDE LH UPPER 1

REVISED, BOLT FASTNERS (ALL M/C'S FROM 19/03/2003)
6 12260120 0 RAM 3
HOPPER LIFT RAMS
7 12230850 0 INCLINED BELT FEEDER SIDE RAM MTG RH 1
INCLINED BELT FEEDER ONLY FROM S/N 12303574
7 12230158 0 SIDE RAM MTG LH 1
INCLINED APRON FEEDER ONLY
8 12230145 0 HOPPER BACK UPPER 1
9 12230281 0 PROTECTOR PLATES RH 1
10 12230142 0 HOPPER BACK 1
11 12230178 0 RETAINING PIN 2

PIN AND WEGDE TYPE (ALL M/C'S UP TO 19/03/2003)
12 12230140 0 HOPPER SIDE RH 1
13 12230143 0 HOPPER SIDE RH UPPER 1

14 12230157 0 SIDE RAM MTG RH 1
INCLINED APRON FEEDER ONLY
14 12230851 0 INCLINED BELT FEEDER SIDE RAM MTG LH 1
INCLINED BELT FEEDER ONLY FROM S/N 12303574
15 12230155 0 APRON FEEDER MTG ANGLE RH 1
16 12360121 0 RAM 2
SLIDER RAM
17 12230134 0 APRON FEEDER SIDE COVER 2
18 06663105 0 HYDRAULIC MOTOR 2

ORDER ITEM 2, PART NO. T119137 ECO11814 AND ECO11866
18 T119137 0 HYDRAULIC MOTOR 1
DIRECT REPLACEMENT FOR ITEM 2, PART NO. 06663105 ECO11814 AND
ECO11866
18 T123741 0 ZHENJIANG BMSY SERIES SEAL KIT SPEC DOC 1

SEAL KIT FOR ITEM 2, PART NO. T119137 ECO11814 AND ECO11866
19 12230274 0 HOPPER OUTLET RH 1

(STRAIGHT TYPE) FROM 19/11/2003
20 12230276 0 RUBBER (OUTLET) 2
21 12230277 0 BELT FEEDER HOPPER OUTLET CLAMP RH 1
22 12230278 0 BELT FEEDER HOPPER OUTLET CLAMP LH 1
23 12230275 0 HOPPER OUTLET LH 1

(STRAIGHT TYPE) FROM 19/11/2003
Page 2
24 12230282 0 PROTECTOR PLATES LH 1
25 12230268 0 SKIRTING RUBBER 2
26 12230267 0 BELT FEEDER SKIRTING SIDE CLAMP 6
27 12230156 0 APRON FEEDER MTG ANGLE LH 1
28 12280105 0 PIN 2
29 12230271 0 RUBBER FLAP 1
30 12230272 0 HOPPER BACK RUBBER STRAP 1
30 12230635 0 HOPPER BACK RUBBER STRAP EXTENDED 1

Replaces 12230272 from July 2006
31 00039090 0 BOLT M39 2
M39X90
32 00039006 0 WASHER 2
M39
33 00039002 0 LOCKNUT 2
M39
34 12230144 0 HOPPER SIDE LH UPPER 1
35 12230145 0 HOPPER BACK UPPER 1
36 12230143 0 HOPPER SIDE RH UPPER 1
37 12230940 0 ONE PIECE HOPPER SIDE LH 1
Optional 11/2004>
38 12230941 0 ONE PIECE HOPPER SIDE RH 1
Optional 11/2004>
39 12230108 0 CLAY HOPPER OUTLET RH 1
Optional 11/2004>
40 12230109 0 CLAY HOPPER OUTLET LH 1
Optional 11/2004>
41 12360122 0 RAM 2
SCREEN ANGLE RAM (NOT SHOWN)
42 12230168 0 HOPPER FRONT EXTENSION PLATE 1
42 12230169 0 HOPPER FRONT EXTENSION PLATE 1

(NOT SHOWN)
[Figure End]
Page 3
THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK
Page 4
NAME: HOPPER HORIZONTAL FEEDER MACHINE: WARRIOR 1800
FIGURE: 01-02 REV: B
Page 5
1 12230286 0 HORIZONTAL EXTENDED HOPPER SIDE LH 1
2 12230172 0 HORIZONTAL HOPPER BACK 1
3 12230285 0 HORIZONTAL EXTENDED HOPPER SIDE RH 1
4 12230178 0 RETAINING PIN 2
5 12230167 0 HOPPER REAR EXTENSION PLATE 1
6 12260126 0 RAM 1
HOPPER LIFT RAM
7 12330966 0 APRON SKIRTING CLAMP LH 1
7 12330967 1 APRON SKIRTING CLAMP RH 1
8 12330968 0 20MM APRON FEEDER SKIRTING RUBBER 2
9 12230267 0 BELT FEEDER SKIRTING SIDE CLAMP 6
10 12230180 0 HORIZ HOPPER OUTLET RH 1
11 12230186 0 RUBBER (OUTLET) 1
12 12230182 0 OUTLET CLAMP RH 1
13 12230183 0 OUTLET CLAMP LH 1
14 12230186 0 RUBBER (OUTLET) 1
15 12230181 0 HORIZ HOPPER OUTLET LH 1
16 12230525 0 ADJUSTER 8
17 12230273 0 HORIZONTAL HOPPER MTG FRAME 1
18 12230279 0 HORIZ FEEDER EXTENDED MTG FRAME 1
19 12230175 0 HOPPER BACK MTG PLATE 2
20 12360128 0 RAM 2
FEEDER LIFT RAM (ALL MACHINES UP TO 02/06/2003)
20 12360129 0 RAM 2
FEEDER LIFT RAM (ALL MACHINES FROM 02/06/2003)
21 12230299 0 FEEDER EXTENDED PIVOT FRAME 1
22 12230269 0 FEEDER FRAME BACK GUARD 1
23 12230189 0 HORIZ BELT FEEDER BACK GUARD 1
24 12330921 2 APRON REAR RUBBER FLAP 1
25 12330924 0 REAR HOPPER CLAMP 1
26 12230175 0 HOPPER BACK MTG PLATE 1

ALL M/C'S UP TO 16/06/2003 (WELDED CLEATS)
27 12230201 0 MOUNTING BRACKET 2
ALL M/C'S FROM 16/06/2003
28 12280101 0 PIN 2
Page 6
29 12230217 0 HOPPER EXTENSION LH 1
30 12230216 0 HOPPER EXTENSION RH 1
31 12260130 0 RAM 2
HOPPER LIFT RAM
32 12230289 0 EXTENDED SKIRTING SIDE CLAMP 2
33 12360127 0 RAM 2
SCREEN ANGLE RAM (NOT SHOWN)
[Figure End]
Page 7
Page 8
NAME: HORIZONTAL BELT FEEDER CONVEYOR MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 01-03 REV: C
Page 9
ILLUSTRATION:
1 12230295 0 BELT FEEDER EXTENDED CONVEYOR 1
2 12230251 0 BELT GEARBOX BEARING MTG LH 1
3 12230252 0 BELT FEEDER GEARBOX MTG RH 1
4 12230253 0 DRIVE DRUM 1
5 12030194 0 805W GEARBOX 2
6 09230195 0 GUIDE ROLLER 4
7 01940145 0 1240MM IMPACT BAR 12

HORIZONTAL FEEDER FROM MC S/N: 12303385
8 12230249 0 PLAIN BELT 1
9 12230263 0 BELT CLEANER FRAME 1
10 12230265 0 BELT CLEANER STRAP 1
11 12230264 0 BELT CLEANER 1
12 09150125 0 TENSIONER (ROSTA) 2
13 12230239 0 IMPACT ROLLER 3

14 12230291 0 MTG BRACKET 4
15 12230261 0 RETURN ROLLER GUARD 2
15 12270476 0 DISC RETURN ROLLER GUARD 2

REPLACES 12230261
16 12230260 0 DISC RETURN ROLLER 2
17 12030185 0 FEEDER TAIL DRUM SCRAPER MTG 1
17 06630187 0 SCRAPER RUBBER 1

(NOT SHOWN)
17 06630188 0 TAIL DRUM SCRAPER STRAP 1
(NOT SHOWN)
18 12230254 0 TAIL DRUM 1
19 12030186 0 FEEDER TAIL DRUM SCRAPER PLATE 1
20 12230257 0 TAIL DRUM MTG ANGLE 2
21 12270130 0 BELT FEEDER UNDERGUARD 1
21 12270131 0 BELT FEEDER UNDERGUARD RH 1
22 00024001 0 NUT 4
23 00024006 0 WASHER 2
24 02420116 0 ADJUSTER ROD 2
25 06630191 0 ADJUSTER SHOE 2
26 12230298 0 EXTENDED SIDE DOOR 2
Page 10
ILLUSTRATION:
27 12230293 0 SIDE DOOR SMALL 2
28 12230292 0 REAR SIDE DOOR 2
29 12230255 0 TAIL DRUM SHAFT 1
30 02023213 0 2+1/2" BEARING 2
31 03210165 0 TAPERLOCK 2
32 12230256 0 TAIL DRUM COLLAR 2
33 12230306 0 IMPACT BED 1

34 12130508 0 IMPACT BAR 24
35 12230238 0 U BOLT 6
U BOLT FOR IMPACT ROLLERS (NOT SHOWN)
[Figure End]
Page 11
Page 12
NAME: APRON FEEDER CONVEYOR MACHINE: WARRIOR 1800
ILLUSTRATION: APRON FEEDER
Page 13
1 12230900 0 APRON FEEDER CONVEYOR 1
2 12230111 0 APRON FEEDER DOOR 8
3 12230118 0 CONVEYOR BACK GUARD 1
4 12230914 0 FEEDER REAR PLATE MTG RH 1
5 12230915 0 FEEDER REAR PLATE MTG LH 1
8 12231119 0 BEARING Supersedes 12230119 22/09/03 3

(Interchangeable)
9 12230224 0 CLAMPING ELEMENT 4
10 12230902 0 DRIVE SHAFT 1
11 12230218 0 SPROCKET 2
12 12230135 0 SUPPORT WHEEL 6
13 12230123 0 GEARBOX 1

14 T123737 0 ZHENJIANG BMTS SERIES SEAL KIT SPEC DOC 1
DIRECT REPLACEMENT FOR ITEM 14, PART NO.12230121 ECO11814 AND
ECO11864
15 12230130 0 APRON FEEDER ROLLER 24
16 12630907 0 FLANGE BEARING ADJUSTER SHOE 2

REPLACES 12230115
17 12230116 0 APRON FEEDER BEARING SHOE 4
18 12230901 0 SHAFT 1
19 12230219 0 SPROCKET 2
20 00030250 0 BOLT HEX 2
21 00030006 0 WASHER 2
22 00030002 0 LOCKNUT 2
23 12230131 0 APRON FEEDER CHAIN 112
24 12230903 0 END MOUNTED SHOE 42

REPLACED BY 12230951
24 12230951 0 WR1400 NEW APRON FEEDER SHOE 42
REPLACES 12230903
26 12230906 0 APRON FEEDER SIDE COVER 2
Page 14
27 12230154 0 DISC SPRING 30
28 12230153 0 APRON FEEDER ADJUSTER BUSH 2
29 12230911 0 GEARBOX MTG BRACKET 1
30 12230912 0 APRON FEEDER COUPLING COVER 1
31 12230913 0 APRON FEEDER COUPLING COVER 1
32 12230907 0 RAM MTG BRACKET RH 1

TO 05/07/2004
32 12230930 0 RH RAM MOUNTING 1
FROM 05/07/2004
33 12230931 0 LH RAM MOUNTING 1
FROM 05/07/2004
33 12230908 0 RAM MTG BRACKET LH 1
TO 05/07/2004
34 12260121 0 RAM 2
35 12230905 0 APRON FEEDER MTG FRAME 1
36 12280109 0 PIN 6
38 12280112 0 PIN 2
39 12280111 0 PIN 2
40 12230952 0 APRON FEEDER SHOE RIBBED 14

REPLACES 12230904
40 12230904 0 RIBBED SHOE 14
41 12230916 0 MOTOR COVER 1
[Figure End]
Page 15
Page 16
NAME: HORIZONTAL FEEDER (RADIAL M/C) MACHINE: WARRIOR 1800
Page 17
NAME: HORIZONTAL FEEDER (RADIAL M/C) MACHINE: WARRIOR 1800
1 12330701 0 FEEDER FRAME BACK GUARD 1
2 12330710 0 FEEDER SUPPORT INNER 1
3 12330704 0 FEEDER SUPPORT OUTER RH 1
4 12330703 0 FEEDER SUPPORT OUTER LH 1
5 12260120 0 RAM 2
[Figure End]
Page 18
NAME: INCLINED BELT FEEDER CONVEYOR MACHINE: WARRIOR 1800
ILLUSTRATION:
Page 19
ILLUSTRATION:
1 12230258 0 PLAIN BELT 1
2 12230238 0 U BOLT 10
3 12230291 0 MTG BRACKET 8
4 12230239 0 IMPACT ROLLER 5
5 12130508 0 IMPACT BAR 24
6 12030194 0 805W GEARBOX 2
7 12230253 0 DRIVE DRUM 1
8 12230252 0 BELT FEEDER GEARBOX MTG RH 1
9 12230251 0 BELT GEARBOX BEARING MTG LH 1
10 12230290 0 BELT FEEDER CONVEYOR FRAME 1
11 12030185 0 FEEDER TAIL DRUM SCRAPER MTG 1

NOT SHOWN
11 06630188 0 TAIL DRUM SCRAPER STRAP 1
NOT SHOWN
12 12030186 0 FEEDER TAIL DRUM SCRAPER PLATE 1
13 12230254 0 TAIL DRUM 1
15 03210165 0 TAPERLOCK 2
16 12231256 0 TAIL DRUM SPACER 2
17 02023213 0 2+1/2" BEARING 2
18 12270131 0 BELT FEEDER UNDERGUARD RH 1
19 12270130 0 BELT FEEDER UNDERGUARD 1
20 02420116 0 ADJUSTER ROD 2
21 00024006 0 WASHER 2
23 00024001 0 NUT 2
24 12230257 0 TAIL DRUM MTG ANGLE 2
25 12230292 0 REAR SIDE DOOR 2
26 12230293 0 SIDE DOOR SMALL 2
27 12230294 0 SIDE DOOR MEDIUM 2
Page 20
ILLUSTRATION:
29 12230261 0 RETURN ROLLER GUARD 2

REPLACES 12230261
30 00016050 0 M16X050 BOLT8.8ZP 2
31 00016006 0 WASHER 2
33 12230263 0 BELT CLEANER FRAME 1
34 00020055 0 BOLT M20 4
35 00020002 0 LOCKNUT 4
36 12230264 0 BELT CLEANER 1
37 12230265 0 BELT CLEANER STRAP 1
38 00012006 0 WASHER 6
39 00012002 0 LOCKNUT 6
40 09230195 0 GUIDE ROLLER 4
[Figure End]
Page 21
Page 22
NAME: SCREENBOX MACHINE: WARRIOR 1800
ILLUSTRATION:
Page 23
ILLUSTRATION:
1 12350105 0 SPRING 12
2 12350550_CA 0 SCREENBOX COMPLETE 1
3 12150525 0 PIPE UNIT 1
4 12350233 0 SCREEN BACK RUBBER BRACKET 1
5 12250229 0 RUBBER 1
6 01150200 0 BEARING HOUSING 2
7 12050491 0 B/HOUSING OUTER CAP 2
8 12050494 0 LIPSEAL 2
9 12050492 0 LABYRINTH SEAL 2
10 05120170 0 GRUBSCREW 9
11 01151175 0 BEARING Supersedes 01150175 and 07250154 22/09/03 2

(Interchangeable)
12 12050490 0 B/HOUSING INNER CAP 2
13 12050493 0 RETAINIING RING 1
14 01151180 0 LOCATING RING Supersedes 01150180 22/09/03 2

(Interchangeable)
NOT USED IN NON DRIVE SIDE BEARING - 12050750_CSA
15 12050495 0 O-RING 2
16 12150450 0 SCREEN SHAFT 1
17 12350351 0 FLYWHEEL C/W TAPERLOCK 2

REPLACES 01450117
18 01800023 0 TAPERLOCK 2
19 01150163 0 10MM FLYWHEEL WEIGHT 18

(FOR 12MM THROW)
(FOR 10MM THROW) - UP TO MACHINE S/N 12301720
20 02050393 0 TAPERLOCK 1
21 02050396 0 R0UND END KEY 1

11X18X50MM
22 02050978 0 PULLEY 1
FROM OCTOBER 2008
22 06010103 0 PULLEY 1
REPLACED BY 02050978 (OCTOBER 2008)
23 12350228 0 SCREEN FEED IN CHUTE RUBBER 1
24 05760510 0 ADAPTOR 2
25 06620141 0 GREASE NIPPLE 2
26 12260491 0 GREASE HOSE 2
27 12350290 0 SCREEN SIDE RUBBER 2
Page 24
ILLUSTRATION:
28 12350292 0 SCREENBOX OUTLET RUBBER 1
29 12350294 0 SCREEN INLET RUBBER 1
30 12150541 0 SIDE RUBBER FLAP STRAP 6
31 12250293 0 SCREENBOX OUTLET RUBBER STRAP 1
32 12350234 0 INLET RUBBER STRAP 3
33 12350274 0 SCREEN SIDE DEFLECTOR RUBBER 2
34 12350272 0 SCREEN SIDE DEFLECTOR RUBBER STRAP RH 1

(SHOWN)
35 12350273 0 SCREEN SIDE DEFLECTOR RUBBER STRAP LH 1
36 02060213 0 DOWTY SEAL 2
37 03210294 0 ADAPTOR 2
38 01150178 0 APQ68/0297/000021 GT GASKET 2
39 12350530 0 BOTTOM DECK LIP BLANKING RUBBER 2

FROM S/N 12302080
39 12250237 0 BOTTOM DECK LIP BLANKING RUBBER 2
ALL M/C'S AFTER 05/05/2003
40 12350563 0 HOUSED BEARING COMPLETE - LOC 1
FROM MACHINE S/N PID00123CDGAC1797
40 12350573 0 HOUSED BEARING COMPLETE - LOC 2
UP TO MACHINE S/N PID00123CDGAA1565
41 12350564 0 HOUSED BEARING COMPLETE - NL 1
SCREENBEARING COMPLETE
42 12150163 0 LORD MOUNT PACKER 2
43 12250350 0 RUBBER BUFFER 2
[Figure End]
Page 25
Page 26
NAME: SCREENBOX TOP DECKS MACHINE: WARRIOR 1800
ILLUSTRATION: SCREENBOX
Page 27
1 12150260 0 TOP DECK MESH FRAME 1
2 12150265 0 RH CLAMP PLATE (5 HOLE) 2
3 12150267 0 CLAMP PLATE MID(4 HOLE) 4
4 12150266 0 LH CLAMP PLATE (5 HOLE) 2
5 12150280 0 PUNCHED PLATE LONG SECTION 2
6 12150270 0 TOP DECK MESH LONG SECTION 2
7 12150281 0 PUNCHED PLATE SHORT SECTION 2
8 12150271 0 TOP DECK MESH SHORT SECTION 2
9 12150257 0 4" TOP DECK BOFOR 4
9 12150679 0 BOFOR DECK 1

5" TOP DECK AVAILABLE AS OPTION ECO11616
9 12150682 0 BOFOR FOR FINGER/MESH COMBINATION 1
4" LONG FIRST SECTION BOFOR (USED IN COMBINATION WITH FINGER
DECKS)
9 12150683 0 3" FIRST SECTION EXTENDED BOFOR 1

3" LONG FIRST SECTION BOFOR (USED IN COMBINATION WITH FINGER
DECKS)
10 12150258 0 TOP DECK BOFOR BLANKING PLATE 1
11 12150535 0 FINGERSCREEN FRAME UPPER 1
12 12150251 0 FINGER ASSY 70
13 12150536 0 TOP DECK FINGERSCREEN FRAME MIDDLE 1
14 12150537 0 TOP DECK FINGER SCREEN FRAME LOWER MID 1
15 12150538 0 TOP DECK FINGER SCREEN FRAME LOWER 1
16 12150539 0 TOP DECK FINGER SCREEN BOLT PROTECTOR 6
17 07250326 0 LOCKNUT 124
18 07250119 0 HARDENED WASHER 36
19 00000070 0 BOLT M20 36
20 06650489 0 TENSIONER SPLITPIN 36
21 06650487 0 SCREEN TENSION WEDGE 36
22 06650488 0 SCREEN TENSION SPACER 36
23 06650486 0 SCREEN TENSION BOLT 36
24 06650490 0 FLAT WASHER 36
25 00000165 0 BOLT M20 18
Page 28
26 00000141 0 BOLT M16 24
27 01150231 0 LOCKNUT 24
28 02010627 0 SPRING WASHER 70
29 12150273 0 CAMBER BAR RUBBER 6
30 12150274 0 CAMBER BAR RUBBER 6
31 00000357 0 SETSCREW 18
[Figure End]
Page 29
Page 30
NAME: SCREENBOX BOTTOM DECKS MACHINE: WARRIOR 1800
Page 31
1 12150530 0 BOTTOM DECK FINGER FRAME 15
2 12150531 0 FINGER BAR 20 MM APPERTURE 15
3 12150512 0 LOCATION PLATE LH 1
4 12150513 0 LOCATION PLATE RH 1
5 01450199 0 DECK TENSIONER(CAMBER BAR) 4

UP TO 17/07/2003 (6MM GUSSETS)
5 01450199 0 DECK TENSIONER(CAMBER BAR) 4
FROM 17/07/2003 ( INTERCHANGABLE, 10MM GUSSETS)
6 N1322802000000Z 0 LOCKNUT 8
8 B1380802001300Z 0 M20 X 130 BOLT 10.9 ZC DIN 931 8
9 06550177 0 PIN 4
10 W1005801600000Z 0 W1005801600000Z 4
11 02020151 0 R-CLIP 4
12 12150520 0 SCREEN TENSION BAR 1700 MM LONG 2
13 02050458 0 WASHER 60
14 01150231 0 LOCKNUT 60
15 00000119 0 BOLT M16 60
16 12150509 0 BOTTOM DECK MESH SHORT 1
17 12150510 0 BOTTOM DECK SPEED HARP SHORT 1
18 12150511 0 BOTTOM DECK MESH LONG 1
19 12150635 0 BOTTOM DECK PUNCH PLATE SHORT 1
20 12150636 0 BOTTOM DECK PUNCH PLATE LONG 1
21 12150660 0 BALL DECK SURFACE LONG SECTION 1
22 12150661 0 BALL DECK CLAMPING FLAT 10
25 12150664 0 BALL DECK SURFACE SHORT SECTION 1
26 12150665 0 NATURAL RUBBER BALL 150
28 N1220801200000Z 0 LOCKNUT 66
29 S3300801200500Z 0 FASTENER 66
Page 32
[Figure End]
Page 33
Page 34
NAME: SCREENBOX DRIVE MACHINE: WARRIOR 1800
ILLUSTRATION:
Page 35
ILLUSTRATION:
1 12350231 0 MOTOR MOUNTING STAND BASE 1

(Interchangeable)
3 12350232 0 MOTOR MOUNTING STAND 1

REPLACED BY 05660315 (OCTOBER 2008)
FROM OCTOBER 2008
5 03210166 0 TAPERLOCK 1
6 06760131 0 SQUARE END KEY 1
7 02050978 0 PULLEY 1
STD FROM OCTOBER 2008
7 02020428 0 PULLEY 1
REPLACED BY 02050978 AS STD (OCTOBER 2008)
8 12150517 0 SPRING TENSION PLATE 1
9 12150518 0 ADJUSTER 1
10 07250170 0 COMPRESSION SPRING 1
11 W1005802400000Z 0 WASHER 2
12 N1320802400000Z 0 LOCKNUT 2
13 B1300802401100Z 0 FASTENER 1
14 W1005801200000Z 0 WASHER 4
15 N1220801200000Z 0 LOCKNUT 4
16 S3300801200500Z 0 FASTENER 4
17 05050125 0 BOLT M12 4
18 03260252 0 PUMP ADAPTOR 2
19 02060229 0 O-RING 2
21 02250316 0 CAP HEAD SCREW 8
22 02060217 0 DOWTY SEAL 2
23 02060204 0 ADAPTOR 1
24 02060218 0 DOWTY SEAL 1
25 02060297 0 ADAPTOR 1
26 01150177 0 V-BELT 3
NEW FROM OCTOBER 2008
26 01800132 0 V BELT 3
Page 36
ILLUSTRATION:
27 06560165 0 PRESSURE RELIEF VALVE 1
28 02060216 0 DOWTY SEAL 3
29 02060203 0 BSP3/4" X 3/4" M/M P/P ADAPTOR 2
30 03560134 0 BSP3/4"M/M/M TEE HEX ADAPTOR 01929 1
31 N1220800600000Z 0 LOCKNUT 2
32 S3300800600700Z 0 FASTENER 2
33 12370280 0 SCREEN MOTOR GUARD 1

ALL M/C FROM 30/06/2003 (HEIGHT OF GUARD INCREASED)
33 12370280 0 SCREEN MOTOR GUARD 1
UP TO 30/06/2003
34 12370281 0 FLYWHEEL GUARD 1
ALL M/C'S FROM 30/06/2003 (HIGHT OF GUARD INCREASED)
34 12370281 0 FLYWHEEL GUARD 1
UP TO 30/06/2003
35 12250265 0 SCREEN DRIP TRAY 2
DISCONTINUED ON M/C'S BUILTS AFTER 30/09/2003
[Figure End]
Page 37
Page 38
NAME: SCREENBOX WALKWAYS MACHINE: WARRIOR 1800
Page 39
1 12350300 0 SUBFRAME 1
2 12230525 0 ADJUSTER 1
3 12280107 0 PIN 2
4 01430917 0 PIVOT PIN COLLAR 2
5 12350450 0 SCREEN WALKWAY RH 1

(SQUARE HANDRAILS) FROM 02/07/2003 NOT INTERCHANGABLE
6 12350451 0 SCREEN WALKWAY LH 1
7 12350470 0 NEW SIDE HANDRAIL 2
8 12250472 0 FRONT HANDRAIL 2
9 12350454 0 SCREEN WALKWAY BRACKET RH 1
10 12350455 0 SCREEN WALKWAY BRACKET LH 1
11 12280104 0 PIN 2
12 12250465 0 SCREEN WALKWAY CHAIN 4
13 12350452 0 SCREEN WALKWAY FOLDING SECTION RH 1
14 12350453 0 SCREEN WALKWAY FOLDING SECTION LH 1
16 12330459 0 FINES CONVEYOR HANGING BRACKET 1

TELESCOPIC FINES CONVEYOR M/C'S ONLY
17 12350311 0 FEEDER UNDER TRAY BOLT IN MOUNT 2
FROM SERIAL NO.PIDOO123CDGCB5982
[Figure End]
Page 40
Page 41
1 12350305 7 SUBFRAME 1
2 12230525 0 ADJUSTER 1
3 12280107 0 PIN 2
4 01430917 0 PIVOT PIN COLLAR 2
5 12350450 1 SCREEN WALKWAY RH 1

BOLT ON HINGE VERSION, (NOT INTERCHANGABLE)
6 12350451 1 SCREEN WALKWAY LH 1
7 12350470 0 NEW SIDE HANDRAIL 2
8 12250472 1 FRONT HANDRAIL 2

MTG HOLE LOCATIONS CHANGED (NOT INTERCHANGABLE)
8 12250473 0 HANDRAIL (NEW APRON) 1
APRON FEEDER M/C'S ONLY (NOT SHOWN)
9 12350454 0 SCREEN WALKWAY BRACKET RH 1
10 12350455 0 SCREEN WALKWAY BRACKET LH 1

(NOT SHOWN)
11 12280104 0 PIN 2
12 12250468 0 SCREEN WALKWAY CHAIN APRON TOP 1

1 OFF PER APRON FEEDER M/C
1 OFF PER APRON FEEDER M/C
4 OFF, ALL VERSIONS EXCEPT FOR APRON FEEDER M/C'S, QTY 2 OFF
13 12350452 1 SCREEN WALKWAY FOLDING SECTION RH 1
14 12350453 1 SCREEN WALKWAY FOLDING SECTION LH 1
16 12330459 0 FINES CONVEYOR HANGING BRACKET 1
TELESCOPIC FINES CONVEYOR M/C'S ONLY (REQUIRES WELDING)
18 06650348 0 BOLT-ON WALKWAY HINGE 4
19 12250467 0 MOTOR PULLEY CLAMP PLATE 1
20 02020428 0 PULLEY 1
22 06950335 0 SQUARE PLUG 10
23 12350311 0 FEEDER UNDER TRAY BOLT IN MOUNT 2

FROM SERIAL NO. PID00123CDGCB5982 ECO12319
[Figure End]
Page 42
NAME: TAIL CONV HEAD SECT (1200mm BELT) MACHINE: WARRIOR 1800
ILLUSTRATION: TAIL CONVEYOR
Page 43
1 12230520 0 TAIL CONV UPPER SECTION FRAME 1
2 12230532 0 TAIL CONV UPPER SKIRTING LH 1

REV 1 UP TO 18/02/2003
3 12230531 0 TAIL CONV UPPER SKIRTING RH 1
REV 1 UP TO 18/02/2003
4 12230543 0 TAIL CONVEYOR SIDE GUARD UPPER 2
5 12230539 0 TAIL CONV SKIRTING UPPER LONG 2
6 12230541 0 GALVANISED CLAMP 8
7 12230521 0 TAIL CONV UPPER BELT SUPPORT 1

REV 1 UP TO 19/02/2003
8 01940145 0 1240MM IMPACT BAR 6
9 06630306 0 DISC RETURN ROLLER L1485 1
10 12270160 0 ROLLER GUARD 1
11 12230522 0 BEARING SUPPORT PLATE 1

UP TO 19/03/2003
11 12230526 0 HEAD DRUM SUPPORT PLATE 1
FROM 19/3/2003 (NOT INTERCHANGABLE)
12 12230527 0 HEAD DRUM SUPPORT PLATE 1
FROM 19/02/2003 (NOT INTERCHANGABLE)
12 12230523 0 BEARING SUPPORT PLATE 1
UP TO 19/03/2003
13 05121159 0 BEARING SUPERSEDES 05120159 22/09/03 2
(INTERCHANGEABLE)
14 06630312 0 TAIL CONVEYOR DRIVE DRUM SPACER 2
15 03210165 0 TAPERLOCK 2
16 06630311 0 DRIVE DRUM SHAFT 1
17 06630240 0 DRUM MTG PLATE LH 1
18 06630310 0 DRIVE DRUM 1
19 02020163 0 TAPERLOCK 1
20 06630241 0 DRUM MTG PLATE RH 1
21 02280265 0 INSERT/CENTRE DISC 1
22 02280264 0 COUPLING FLANGE 2
23 06630255 0 HYDRAULIC MOTOR STAND 1
24 06630256 0 COUPLING COVER PLATE 2
25 02220220 0 TAPERLOCK 1

OMV 800
27 06670215 0 DRUM UNDERGUARD 1
Page 44
28 09275120 0 BEATER ROLLER 1
30 09230195 0 GUIDE ROLLER 4
31 12230525 0 ADJUSTER 2
[Figure End]
Page 45
Page 46
NAME: TAIL CONV TAIL SECT (1200mm BELT) MACHINE: WARRIOR 1800
Page 47
1 12230510 0 TAIL CONVEYOR LOWER SECTION FRAME 1
2 12230551 0 SKIRTING LOWER RH 1
3 12230552 0 SKIRTING LOWER LH 1
4 12230540 0 SKIRTING UPPER SHORT 2
5 12230554 0 ACCESS COVER PLATE 2
9 12230535 0 FEEDBOOT SKIRTING LOWER LONG 2
10 12270155 0 ROLLER GUARD 1
12 N1200802400000Z 0 NUT 4
13 W1005802400000Z 0 WASHER 2
14 02420116 0 ADJUSTER ROD 2
15 06630190 0 ADJUSTER END CAP 2
17 12230544 0 RUBBER 1
18 12230545 0 F/BOOT RUBBER CLAMP 1

UP TO 24/03/2003
18 12010131 0 CLAMP 3
FROM 24/03/2003
19 09230195 0 GUIDE ROLLER 2
22 02023213 0 2+1/2" BEARING 2
24 02020163 0 TAPERLOCK 2
25 12230515 0 TAIL DRUM 1
26 12230560 0 REAR RUBBER MOUNTING 1
27 12230561 0 RUBBER (REAR) 1
28 12230562 0 CLAMP 1
UP TO 24/03/2003
28 12010131 0 CLAMP 5
Page 48
FROM 24/03/2003
29 12010131 0 CLAMP 5
FROM 24/03/2003
29 12230556 0 REAR GUARD RUBBER CLAMP 1
UP TO 24/03/2003
30 12230555 0 RUBBER 1
31 12270115 0 REAR SIDE GUARD LH 1
32 12270117 0 REAR GUARD 1
33 12270116 0 REAR SIDE GUARD RH 1
34 12230546 0 TAILDRUM SCRAPER 1
36 12030188 1 TAIL DRUM SCRAPER RUBBER STRAP 2
37 12230548 0 SCRAPER PLATE 1
38 12230553 0 SKIRTING SUPPORT ANG 1
39 01940145 0 1240MM IMPACT BAR 16
40 12230505 0 TAIL CONVEYOR BELT 1
41 12230557 0 FEEDBOOT PLATE LH 1
42 12230558 1 FEEDBOOT PLATE RH 1
43 12260123 0 RAM 2
44 12260124 0 RAM 2
45 12010131 0 CLAMP 13
NEW RUBBER CLAMPING SYSTEM
[Figure End]
Page 49
Page 50
Page 51
1 12330520 0 TAIL CONVEYOR HEAD SECTION 1
2 12330557 0 TAIL CONVEYOR SKIRTING UPPER 1
3 12330556 0 TAIL CONVEYOR UPPER SKIRTING 1
4 12370107 0 TAIL CONVEYOR SIDE GUARD 2
5 12330563 0 TAIL CONVEYOR SKIRTING RUBBER 2
9 12330535 0 TAIL CONVEYOR UPPER DEFLECTOR RH 1
10 12330536 0 TAIL CONVEYOR UPPER DEFLECTOR LH 1

REPLACES 12370102
11 12370102 0 TAIL CONVEYOR UPPER DISC ROLLER GUARD 1
13 12330511 0 SIDE IMPACT BAR MTG SHORT 2
14 02020605 0 SIDE ROLLER RH 2
15 12130508 0 IMPACT BAR 2
16 01940145 0 1240MM IMPACT BAR 6
17 02020604 0 SIDE ROLLER LH 2

(SHOWN)
21 12330521 0 TAIL CONVEYOR BELT SUPPORT 1
22 05120170 0 GRUBSCREW 2
23 12330531 0 TAIL CONVEYOR DRIVE DRUM SHAFT 1
24 12330530 0 DRIVE DRUM 1

(INTERCHANGEABLE)
28 03210165 0 TAPERLOCK 2
Page 52
29 06630317 0 COLLAR 2
30 02020163 0 TAPERLOCK 1
33 02220220 0 TAPERLOCK 1
34 06630255 0 HYDRAULIC MOTOR STAND 1

OMV 800
37 12230525 0 ADJUSTER 2
39 12330505 0 BELT (TROUGH) 1

(NOT SHOWN)
[Figure End]
Page 53
Page 54
Page 55
1 12330500 0 TAIL CONVEYOR LOWER SECTION 1400MM WIDE 1
2 12330552 0 TAIL CONVEYOR LOWER SKIRTING NEW 1
3 12330553 0 TAIL CONVEYOR LOWER SKIRTING 1
4 12370105 0 TAIL CONVEYOR SIDE GUARD RH 1
5 12370106 0 TAIL CONVEYOR SIDE GUARD LH 1
6 12370104 0 TAIL CONVEYOR LOWER SIDE GUARD 2
7 07220153 0 CLAMP PLATE 2
10 12330538 0 TAIL CONV LOWER DEFLECTOR PLATE LH LONG 1
11 12330537 0 TAIL CONV LOWER DEFLECTOR PLATE RH LONG 1
12 12330540 0 TAIL CONV LOWER DEFLECTOR PLATE LH SHORT 1
13 12330539 0 TAIL CONV LOWER DEFLECTOR PLATE RH SHORT 1
14 12330511 0 SIDE IMPACT BAR MTG SHORT 2
15 12330510 0 TAIL CONVEYOR IMPACT BAR MOUNTING 45° 2
16 12130508 0 IMPACT BAR 2
17 01940145 0 1240MM IMPACT BAR 15
21 12330506 0 TAIL CONVEYOR ADJUSTER ROD 2
24 12330561 0 TAIL CONVEYOR HANGING RUBBER 1
25 12010131 0 CLAMP 10
26 12260124 0 RAM 2
SLIDE RAM
27 12330550 0 TAIL CONVEYOR V PLOUGH CLAMP 2
28 12330549 0 TAIL CONVEYOR V PLOUGH RUBBER 1
29 12330548 0 TAIL CONVEYOR TAIL DRUM SCRAPER 1
30 12330546 0 TAIL CONVEYOR V PLOUGH 1
Page 56
32 02023213 0 2+1/2" BEARING 2
34 02020163 0 TAPERLOCK 2
35 12330562 0 TAIL CONVEYOR REAR ANGLE SUPPORT 1
36 12330545 0 TAIL CONVEYOR REAR RUBBER 1
37 12370103 0 TAIL CONVEYOR TAIL DRUM REAR GUARD 1
38 12270116 0 REAR SIDE GUARD RH 1
39 12270115 0 REAR SIDE GUARD LH 1
40 12330515 0 TAIL DRUM 1
42 12370100 0 L1690 DISC RETURN ROLLER GUARD 1

REPLACES 12370100
43 05120170 0 GRUBSCREW 2
44 12330568 0 TAIL CONVEYOR EXTENSION PLATE 1

(SHOWN)
45 12330567 0 TAIL CONVEYOR EXTENSION PLATE 1
47 12330505 0 BELT (TROUGH) 1

(NOT SHOWN)
48 12330501 0 SLIDE RAM MOUNTING 1
(SHOWN)
49 12330502 0 SLIDE RAM MOUNTING LH 1
50 B1300802402100Z 0 FASTENER 2
51 W1005802400000Z 0 WASHER 2
52 N1320802400000Z 0 LOCKNUT 2
53 02020537 0 BOLT M16 10
54 S3300801600400Z 0 M16 X 40 SET 8.8 ZC DIN 933 10
55 12330560 0 TAIL CONVEYOR RUBBER CLAMP 1
56 12260123 0 RAM 2
RAISE / LOWER RAM (NOT SHOWN)
[Figure End]
Page 57
Page 58
NAME: SIDE/FINES CONVEYOR HEAD SECTION MACHINE: WARRIOR 1800
ILLUSTRATION:
Page 59
ILLUSTRATION:
1 12330440 0 SIDE CONVEYOR UPPER MIDDLE FRAME 1
2 12330430 0 MID SECTION SKIRTING 2
3 12330433 0 SKIRTING MTG BRACKET RH BOTTOM 4
4 12330432 0 SIDE CONV SKIRTING MTG BRACKET LH TOP 2
5 12330431 0 SKIRTING MTG BRACKET RH TOP 2
6 12330427 0 RUBBER SKIRTING JOINING SECTION 2
7 12230442 0 FINES CONVEYOR HOOP 2
8 05120115 0 ROLLER 3
11 06930471 0 SIDE ROLLER 1
12 06930470 0 SIDE ROLLER 1
13 12270270 0 HEADDRUM GUARD 1
14 12360126 0 RAM 2
14 12360145 0 SIDE CONVEYOR FOLD RAM (ALL METRIC) 4
NEW RAMS REPLACE 12360135
15 12330477 1 SIDE CONVEYOR PLASTIC RAM COVER 2
REPLACES 12330460 - FROM S/N 12303142
15 12330460 0 RAM COVER 2
16 10160120 0 1.5" X 75MM LONG PIN C/W WASHER 2
FROM S/N 12305063
16 00039090 0 BOLT M39 2
18 12270276 0 ROLLER GUARD 1

REPLACES 12270276
19 12330439 0 RH TOP SECTION STONE GUARD 1
20 12330438 0 LH TOP SECTION STONE GUARD 1
21 12330450 0 UPPER HEAD FRAME 1

(Interchangeable)
24 02020211 0 TAPERLOCK 2
Page 60
ILLUSTRATION:
26 12230414_CSA 0 SIDE CONVEYOR DRIVE DRUM COMPLETE 1

SIDE CONVEYOR
26 12230757_CSA 0 SIDE CONVEYOR DRIVE DRUM COMP (FINES) 1
FINES CONVEYOR
28 12230408 0 DRIVE DRUM COLLAR 1
29 02010138 0 TAPERLOCK 1
31 05110105 0 INSERT/CENTER DISC 1
32 01800123 0 TAPERLOCK 1
STD
32 03510147 0 TAPERLOCK 1
FOR OPTIONAL OMT 500
33 12230325 0 HYD MOTOR STAND 1
STD
34 06930266 0 MOTOR UNDERGUARD 2

ECO11828

SEAL KIT FOR ITEM 38 PART NO. T123737 ECO11814 AND ECO11828
36 12230468 0 SCRAPER FRAME 1
37 12130459 0 BELT CLEANER 1
38 12130458 0 SCRAPER CLAMP 1
39 06630260 0 SCRAPER BRACKET RH 1
40 06630261 0 SCRAPER BRACKET LH 1
41 06930139 0 TENSIONER 2
42 02030635 0 RIGGING SCREW 1
43 12230754 0 HEAD SECT ADJ BRACKET 1
44 06550177 0 PIN 2
45 02060202 0 02060215 2
46 02060215 0 02060215 2
47 12230756 0 FOLDING STAYS 2
48 12230752 0 TRANSPORT BRACKETS 2

48 12230775 0 MID SIDE CONV TRANSPORT HOOK 2
S/N 12305066 (MID PRODUCT CONV)
48 12230776 0 FINES SIDE CONV TRANSPORT HOOK 1
S/N 12305066 (FINES PRODUCT CONV)
49 12230238 0 U BOLT 2
Page 61
ILLUSTRATION:
50 00010006 0 M10 WASHER 4
51 00010002 0 LOCKNUT 4
52 12230780 0 ANTI ROLL BACK FRAME 1

(OPTIONAL)
53 12230782 0 ANTI ROLL BACK BAR 14
(OPTIONAL)
54 12230784 0 ANTI ROLL BACK TRANSPORT BAR 1
(OPTIONAL)
55 12230783 0 ANTI ROLL BACK PIN 2
(OPTIONAL)
56 12230780 0 ANTI ROLL BACK FRAME 1
(OPTIONAL)
57 00039006 0 WASHER 2
58 12330525 0 SPLIT PIN 75X6 2

FROM S/N 12305063
[Figure End]
Page 62
NAME: SIDE/FINES CONVEYOR MIDDLE SECTIONS MACHINE: WARRIOR 1800
ILLUSTRATION:
Page 63
ILLUSTRATION:
1 12330420 0 SIDE CONVEYOR MIDDLE FRAME 1
2 12330426 0 LOWER SECTION SKIRTING LH 1
3 12330425 0 LOWER SECTION SKIRTING RH 1
5 12330460 0 RAM COVER 2

REPLACES 12330460 - FROM S/N 12303142
6 12360145 0 SIDE CONVEYOR FOLD RAM (ALL METRIC) 4
NEW RAMS REPLACE 12360135
6 12360126 0 RAM 2
7 12330491 0 SKIRTING (FBOOT RH) 1
8 12330490 0 SKIRTING (FBOOT LH) 1
9 12330493 0 RH SKIRTING MOUNTING 1
10 12330492 0 LH SKIRTING MOUNTING 1
11 06930471 0 SIDE ROLLER 1
12 05120115 0 ROLLER 2
13 06930470 0 SIDE ROLLER 1

REPLACES 12270276
14 12270276 0 ROLLER GUARD 1
16 12230756 0 FOLDING STAYS 1
17 13030111 0 SIDE ROLLER 1
18 13030110 0 SIDE ROLLER 1
19 12230435 0 SUPPORT ARM 2
20 12230460 0 INNER SUPPORT ARM 2
21 12260125 0 RAISE/LOWER RAM 2
22 12280103 0 SIDE CONVEYOR PIN 2

FROM S/N TBC
23 00039090 0 BOLT M39 4
24 00039006 0 WASHER 4
25 00039002 0 LOCKNUT 4
25 12330525 0 SPLIT PIN 75X6 4
Page 64
ILLUSTRATION:
FROM S/N TBC
26 00024180 0 BOLT M24 2
27 00024006 0 WASHER 2
28 00024002 0 LOCKNUT 2
29 02280109 0 ADAPTOR 2
30 02060266 0 ADAPTOR 1
31 12230238 0 U BOLT 2
32 12330494 0 SKIRTING RUBBER (LH) 1
32 12330495 0 SKIRTING RUBBER (RH) 1
[Figure End]
Page 65
Page 66
NAME: SIDE / FINES CONVEYOR LOWER SECTION MACHINE: WARRIOR 1800
ILLUSTRATION: SIDE/FINES CONVEYOR
Page 67
1 12330400 0 SIDE CONV LOWER FRAME 1
2 12230470 0 FEEDBOOT 1
2 12230487 0 SIDE CONVEYOR FEEDBOOT (REVERSED) 1

(OPTION)
3 12230477 0 FEEDBOOT EXTENSION 1
*ALL M/C'S UP TO 06/07/2003* REPLACED BY 12230399
3 12230399 0 FEEDBOOT EXTENSION FOR SPRING BELT CLEANER 1
NEW FROM FEB 2008
3 12230384 0 FEEDBOOT EXTENSION (REVERSE) 1
(OPTION)
4 12330405 0 SIDE CONVEYOR TAIL DRUM ADJUSTER 2
5 12230415 0 SIDE FEED BOOT RUBBER 1
7 12230472 0 FEEDBOOT REAR RUBBER 1
8 12230476 0 FEEDBOOT REAR CLAMP PLATE 1

*ALL M/C'S UP TO 15/09/2003*
8 12010131 0 CLAMP 3
*ALL M/C'S FROM 15/09/2003*
9 12230471 0 FEEDBOOT SIDE RUBBER 2
UP TO SERIAL NO.PID00123KDGB62921 ECO11176
9 12230469 0 SIDE CONV FEEDBOOT SIDE RUBBER 2
FROM SERIAL NO.PID00123KDGB62922 ECO11176
10 12230473 0 SIDE RUBBER CLAMP PLATE RH 1
11 12230474 0 SIDE RUBBER CLAMP PLATE LH 1

(NOT SHOWN)
12 12330407 0 WR1800 SIDE CONVEYOR PLAIN BELT 1
13 06530103 0 ROLLER 1
14 12230491 0 ROLLER BRACKET LH 1
15 12230490 0 ROLLER BRACKET RH 1
16 12230422 0 TAIL DRUM ADJUSTMENT PLATE 1

OLD TYPE USED BEFORE ROLLER WAS INTRODUCED
16 05420143 0 ROLLER 1
17 12230423 0 TAIL DRUM ADJUSTMENT PLATE MTG 1

OLD TYPE USED WITH TAIL DRUM ADJUSTMENT PLATE
17 12230705 0 SIDE CONV ROLLER MTG BRACKET 1

19 12230411 0 TAILDRUM SCRAPER PLATE 1
21 12230412 0 BELT CLEANER 1
22 12230413 0 STRAP 2
Page 68
23 12270250 0 RH SIDE GUARD 1
24 12270251 0 LH SIDE GUARD 1
25 12270252 0 F/BOOT REAR GUARD 1
26 12320125 0 BTM PRODUCT SIDE CONVEYOR MOUNT 1

*FINES CONVEYOR ONLY*
27 12130508 0 IMPACT BAR 6
900 LG
28 06630481 0 DRUM ADJUSTER SHOE 2
29 15530815 0 TAIL DRUM 1
31 09900405 0 TNP2" 3 BEARING 2
32 02020211 0 TAPERLOCK 2
33 02420116 0 ADJUSTER ROD 2
34 00024001 0 NUT 4
35 00024006 0 WASHER 2
36 12230486 0 RUBBER CLAMP 1

*ALL M/C'S FROM 06/07/2003* (NOT INTERCHANGABLE)
36 12230479 0 FEEDBOOT EXTENSION RUBBER CLAMP 1
*ALL M/C'S UP TO 06/07/2003*
37 12230478 0 FEEDBOOT EXTENSION RUBBER 1
*ALL M/C'S FROM 06/07/2003* (NON INTERCHANGABLE) REPLACED BY
12230383

*ALL M/C'S FROM 06/07/2003* (NON INTERCHANGABLE) REPLACED BY
12230383

NEW FROM FEB 2008
38 12230762 0 FEEDBOOT DEFLECTOR 1
*SIDE CONVEYOR ONLY * (FROM 01/09/2003)
39 12230728 0 SIDE CONV FEEDBOOT END RUBBER 2
40 12230729 0 SIDE CONVEYOR FEEDBOOT DEFLECTOR 1
41 09230195 0 GUIDE ROLLER 2

NOT SHOWN
43 03210294 0 ADAPTOR 1
44 12230732 0 12230732 2
FROM SERIAL NO. PID00123CDGB83384
[Figure End]
Page 69
Page 70
NAME: TELE SIDE CONVEYOR HEAD SECTION MACHINE: WARRIOR 1800
ILLUSTRATION: TELE SIDE CONVEYOR HEAD SECTION
Page 71
1 12330467 0 TELE SIDE CON UP MID 1
2 12330800 0 SIDE CONV HEAD SECTION SINGLE RAM TELESCOPIC 1
3 12330810 0 SIDE CONV SINGLE RAM TELESCOPIC SLIDING 1

FRAME
4 12330434 0 TELE SIDE CONV MID SECT SKIRTING 2
5 12230775 0 MID SIDE CONV TRANSPORT HOOK 2

S/N 12305066 (MID PRODUCT CONV & 1 PER FINES CONV)
5 12230752 0 TRANSPORT BRACKETS 2
7 12230442 0 FINES CONVEYOR HOOP 2

USED ON MID PRODUCT CONVEYOR ONLY
8 12330433 0 SKIRTING MTG BRACKET RH BOTTOM 2
USED ON FINES SIDE CONVEYOR ONLY
9 12330432 0 SIDE CONV SKIRTING MTG BRACKET LH TOP 1
10 12330431 0 SKIRTING MTG BRACKET RH TOP 1
REPLACES 12330460 - FROM S/N 12303142
11 12330460 0 RAM COVER 2
12 12230238 0 U BOLT 2
13 12360125 0 RAM 2
15 12270276 0 ROLLER GUARD 1
16 12370287 0 RH TOP SECTION STONE GUARD TELESCOPIC 1
17 12370286 0 LH TOP SECTION STONE GUARD TELESCOPIC 1
18 12330289 0 TELE HEAD SECTION SKIRTING RUBBER 2
19 12280102 0 PIN 2
20 12330453 0 SIDE CONVEYOR BELT SUPPORT TELESCOPIC 1
21 12330454 0 PLAIN BELT(TELESOPIC) 1

NOT SHOWN
22 05120115 0 ROLLER 5
23 06930470 0 SIDE ROLLER 1
24 06930471 0 SIDE ROLLER 1
27 12360124 0 RAM 1
Page 72

REPLACES 12270274
28 12270274 0 TELE HEAD SECTION DISC ROLLER GUARD 1

ONLY USED WITH CHEVRON BELT
30 12270240 1 1
USED ONLY WITH A CHEVRON BELT
31 12270241 0 SINGLE RAM TELE SIDE BEATER GUARD LH 1
USED ONLY WITH A CHEVRON BELT
33 12130459 0 BELT CLEANER 1
35 06930139 0 TENSIONER 2
38 12370288 2 HEADDRUM GUARD 1
39 12370285 0 HEAD DRUM GUARD MTG ANGLE 2

(Interchangeable)
44 02020211 0 TAPERLOCK 2
46 02010138 0 TAPERLOCK 1
49 03510147 0 TAPERLOCK 1
53 12230417 1 DRIVE DRUM 1
53 12230757 0 DRIVE DRUM 1
54 12330475 0 CHEVRON BELT (TELESCOPIC) 1

Not Shown
[Figure End]
Page 73
Page 74
NAME: TELESCOPIC SIDE / FINES CONV MID MACHINE: WARRIOR 1800
ILLUSTRATION:
Page 75
ILLUSTRATION:
1 12330465 10 TELESCOPIC CONVEYOR MIDDLE FRAME 1
2 12330426 0 LOWER SECTION SKIRTING LH 1
3 12330425 0 LOWER SECTION SKIRTING RH 1
5 12330460 0 RAM COVER 2

REPLACES 12330460 - FROM S/N 12303142
6 12360125 0 RAM 2
7 12330491 0 SKIRTING (FBOOT RH) 1
8 12330490 0 SKIRTING (FBOOT LH) 1
9 12330493 0 RH SKIRTING MOUNTING 1
10 12330492 0 LH SKIRTING MOUNTING 1
11 06930471 0 SIDE ROLLER 1
12 05120115 0 ROLLER 2
13 06930470 0 SIDE ROLLER 1
14 12270276 0 ROLLER GUARD 1

REPLACES 12270276
16 12230495 0 TRANSPORT BRACKET 1

UP TO 15/05/2003
17 13030111 0 SIDE ROLLER 1
18 13030110 0 SIDE ROLLER 1
19 12230435 0 SUPPORT ARM 2
20 12230460 0 INNER SUPPORT ARM 2
22 12280103 0 SIDE CONVEYOR PIN 2

FROM S/N TBC
23 00039090 0 BOLT M39 4
24 00039006 0 WASHER 4
25 00039002 0 LOCKNUT 4
Page 76
ILLUSTRATION:
25 12330525 0 SPLIT PIN 75X6 4
FROM S/N TBC
26 00024180 0 BOLT M24 2
27 00024006 0 WASHER 2
28 00024002 0 LOCKNUT 2
30 12010131 0 CLAMP 10
TO FIT SKIRTING RUBBER (NOT SHOWN)
[Figure End]
Page 77
Page 78
NAME: TELESCOPIC SIDE / FINES CONV LOWER MACHINE: WARRIOR 1800
ILLUSTRATION: TELE SIDE / FINES CONVEYOR
Page 79
1 12330400 0 SIDE CONV LOWER FRAME 1
2 12230470 0 FEEDBOOT 1

3 12230399 0 FEEDBOOT EXTENSION FOR SPRING BELT CLEANER 1
NEW FROM FEB 2008
4 12330405 0 SIDE CONVEYOR TAIL DRUM ADJUSTER 2
6 12230437 0 FEEDBOOT RUBBER CLAMP 1

(NOT SHOWN) REPLACED BY ITEM 8
8 12230476 0 FEEDBOOT REAR CLAMP PLATE 1

*ALL M/C'S UP TO 15/09/2003*
8 12010131 0 CLAMP 3
*ALL M/C'S FROM 15/09/2003*
9 12230471 0 FEEDBOOT SIDE RUBBER 2
UP TO SERIAL NO. PID00123KDGB62921 ECO11176
9 12230469 0 SIDE CONV FEEDBOOT SIDE RUBBER 2
11 12230474 0 SIDE RUBBER CLAMP PLATE LH 1

(NOT SHOWN)
12 12330454 0 PLAIN BELT(TELESOPIC) 1
13 06530103 0 ROLLER 1
14 12230491 0 ROLLER BRACKET LH 1
15 12230490 0 ROLLER BRACKET RH 1

OLD TYPE USED BEFORE ROLLER WAS INTRODUCED
16 05420143 0 ROLLER 1
17 12230423 0 TAIL DRUM ADJUSTMENT PLATE MTG 1


19 12230411 0 TAILDRUM SCRAPER PLATE 1
21 12230412 0 BELT CLEANER 1
22 12230413 0 STRAP 2
23 12270250 0 RH SIDE GUARD 1
24 12270251 0 LH SIDE GUARD 1
Page 80
25 12270252 0 F/BOOT REAR GUARD 1
26 12320125 0 BTM PRODUCT SIDE CONVEYOR MOUNT 1

*FINES CONVEYOR ONLY*
27 12130508 0 IMPACT BAR 6
900 LG
29 15530815 0 TAIL DRUM 1
31 09900405 0 TNP2" 3 BEARING 2
32 02020211 0 TAPERLOCK 2
33 02420116 0 ADJUSTER ROD 2
34 00024001 0 NUT 4
35 00024006 0 WASHER 2
36 12230479 0 FEEDBOOT EXTENSION RUBBER CLAMP 1

*ALL M/C'S UP TO 06/07/2003*
36 12230486 0 RUBBER CLAMP 1
*ALL M/C'S FROM 06/07/2003* (NOT INTERCHANGABLE)
NEW FROM FEB 2008
38 12230762 0 FEEDBOOT DEFLECTOR 1
*SIDE CONVEYOR ONLY * (FROM 01/09/2003)
39 12230728 0 SIDE CONV FEEDBOOT END RUBBER 2
40 12230729 0 SIDE CONVEYOR FEEDBOOT DEFLECTOR 1
41 09230195 0 GUIDE ROLLER 2

NOT SHOWN
43 03210294 0 ADAPTOR 2
44 12230732 0 12230732 1
FROM SERIAL NO. PID00123CDGB83384
[Figure End]
Page 81
Page 82
NAME: COLLECTION CONVEYOR TAIL DRUM MACHINE: WARRIOR 1800
ILLUSTRATION: COLLECTION CONVEYOR
Page 83
1 12330300 0 COLLECTION CONVEYOR 1
2 09830421 0 BEARING ADJUSTER 2
3 09830130 0 END CAP 2

REPLACED BY 12230395 (1/OFF) - AUGUST 2006
4 06930243 0 ADJUSTER ROD 2
5 09900405 0 TNP2" 3 BEARING 2
6 12230315 1 TAIL DRUM 1
7 02020163 0 TAPERLOCK 2
9 02020165 0 ROUND END KEY 2
10 12230320 2 DRUM SCRAPER 1
12 12230323 0 BELT CLEANER 1
14 12330330 3 FEEDBOOT 1
15 12330331 0 COLLECTION CONV FEEDBOOT SKIRTIN RUBBER 2

UP TO SERIAL NO. PID00123KDGB62921 ECO11176
15 12330384 1 COLLECTION CONVEYOR SKIRTING RUBBER 2
19 12230333 0 FEEDBOOT REAR RUBBER STRAP 1

FROM 29/03/2003 (REPLACE ITEM 19) INTERCHANGABLE
22 12330335 0 FEEDBOOT EXTEN RH 1
23 12330336 0 FEEDBOOT EXTEN LH 1
24 12330337 0 FEEDBOOT EXTENSION SUPPORT 1
25 12330338 0 FEEDBOOT EXTENSION SUPPORT LH 1
26 12270151 0 SIDE GUARD RH 1
27 12270153 0 REAR GUARD 1
Page 84
30 12270157 0 COLLECTION CONVEYOR DISC ROLLER GUARD 2
30 12270478 0 LOWER DISC ROLLER GUARD 1

REPLACES 12270157
32 12270152 0 SIDE GUARD LH 1
33 12230680 0 ROLLER 15
34 12270159 0 SIDE GUARD 4
35 12270156 0 COLLECTION CONV SIDE GUARD UPPER 2
36 12330333 0 DRIVE DRUM RUBBER 1
37 12330334 0 DRIVE DRUM RUBBER CLAMP 1
38 09230195 0 GUIDE ROLLER 2
39 12330305 0 BELT 1
40 00024006 0 WASHER 2
41 00016006 0 WASHER 4
42 00016002 0 LOCKNUT 4
43 00012006 0 WASHER 70
44 00012030 0 BOLT M12 16
45 02060213 0 DOWTY SEAL 2
46 03210294 0 ADAPTOR 2
47 03210361 0 FASTENER 2
48 00012002 0 LOCKNUT 92
49 00012040 0 BOLT M12 30
50 01800176 0 HOOK BOLT ON 4
52 00012035 0 M12X035 SETSCW8.8ZP 22
53 00020001 0 NUT 2
54 00010006 0 M10 WASHER 68
55 00010002 0 LOCKNUT 68
56 00000222 0 U BOLT 34
57 12010131 0 CLAMP 4
FROM 29/03/2003 (REPLACE ITEM 19) INTERCHANGABLE
[Figure End]
Page 85
Page 86
NAME: COLLECTION CONVEYOR DRIVE DRUM MACHINE: WARRIOR 1800
Page 87
1 12270158 0 HEAD DRUM GUARD 1

(Interchangeable)
4 12230310 0 DRIVE DRUM 1
5 02020163 0 TAPERLOCK 2
6 02020165 0 ROUND END KEY 3
7 12230357 0 BLADE SCRAPER CLAMPING FLAT 1

FROM 02/06/2003
9 02010138 0 TAPERLOCK 1
12 01800123 0 TAPERLOCK 1
STD
12 03510147 0 TAPERLOCK 1
13 06930265 0 MOTOR MOUNTING BRACKET 1
TO SUIT STANDARD OMH 500
STANDARD OMH 500
16 12230351 0 SCRAPER MOUNTING 1

UP TOP 02/06/2003 (REPLACED BY ITEM 39 INTERCHANGABLE)
17 12230350 0 BELT CLEANER 1
18 06930139 0 TENSIONER 2
20 00012006 0 WASHER 68
21 00012002 0 LOCKNUT 62
22 00010006 0 M10 WASHER 12
23 00010002 0 LOCKNUT 12
24 00010040 0 BOLT M10 2
25 00012040 0 BOLT M12 36
26 00000060 0 BOLT M16 4
27 00016050 0 M16X050 BOLT8.8ZP 24
28 00016002 0 LOCKNUT 24
Page 88
29 00012070 0 BOLT M12 2
30 02060213 0 DOWTY SEAL 3
31 03210294 0 ADAPTOR 3
32 00012030 0 BOLT M12 24
33 02060216 0 DOWTY SEAL 2
35 02020662 0 BOLT M16 8
36 00016006 0 WASHER 24

OMT 500 OPTIONAL FROM 19/05/2003
TO SUIT OPTIONAL OMT 500 FROM 18/09/2003
39 12230354 0 BLADE SCRAPER FRAME 2
FROM 02/06/2003 (REPLACES ITEM 16 INTERCHANGABLE)
[Figure End]
Page 89
Page 90
NAME: EXTENDED COLLECTION CONVEYOR LOWER MACHINE: WARRIOR 1800
Page 91
2 12330314 0 RADIAL FEEDBOOT 1
3 12270159 0 SIDE GUARD 6
5 12330320 1 LOWER REFLECTOR LH 1
7 12330319 0 LOWER DEFLECTOR RH 1
10 12330310 0 COLLECTION CONVEYOR LOWER 1

REPLACES 12270157
13 12270151 0 SIDE GUARD RH 1
15 06930243 0 ADJUSTER ROD 2
16 09830130 0 END CAP 2

REPLACED BY 12230395 (1/OFF) - AUGUST 2006
18 12270152 0 SIDE GUARD LH 1
19 09230195 0 GUIDE ROLLER 2
20 12230320 2 DRUM SCRAPER 1
21 12230323 0 BELT CLEANER 1
22 12230322 0 STRAP 2
24 09900405 0 TNP2" 3 BEARING 2
25 12230315 1 TAIL DRUM 1
26 12270153 0 REAR GUARD 1
27 12330339 0 COLL CONV SKIRTING RUBBER 2
28 12230680 0 ROLLER 18
Page 92
29 03220103 0 ROLLER 2
[Figure End]
Page 93
Page 94
NAME: EXTENDED COLLECTION CONVEYOR MID MACHINE: WARRIOR 1800
Page 95
NAME: EXTENDED COLLECTION CONVEYOR MID MACHINE: WARRIOR 1800
1 12330368 0 MID SKIRTING LH 1
2 12330369 0 MID SKIRTING RH 1
4 03220103 0 ROLLER 5
6 12330361 0 COLLECTION CONVEYOR MID 1

REPLACES 12270157
9 02060266 0 ADAPTOR 1
10 02280109 0 ADAPTOR 2
11 12330328 0 COLL CONV HEAT SHIELD 1
[Figure End]
Page 96
NAME: EXTENDED COLLECTION CONVEYOR HEAD MACHINE: WARRIOR 1800
Page 97
NAME: EXTENDED COLLECTION CONVEYOR HEAD MACHINE: WARRIOR 1800
1 12130841 0 SKIRTING TOP 1
2 12130840 0 SKIRTING MID SECTION TOP RH 1
3 12170235 0 CONVEYOR HEADDRUM GUARD 1

(INTERCHANGEABLE)
5 06630318 0 COLLAR 2
6 06630310 1 DRIVE DRUM 1
12 06630355 0 TAIL CONV MOTOR STAND OMT TYPE 1
15 03510164 0 TAPERLOCK 1
17 02020163 0 TAPERLOCK 1

RIGHT HAND SIDE
LEFT HAND SIDE
21 12130518 0 RETURN ROLLER BRACKET 1
22 06630302 0 RETURN ROLLER NIP GUARD 1

REPLACES 06630306
25 03220103 0 ROLLER 2
[Figure End]
Page 98
NAME: EXTENDED COLLECTION CONVEYOR MACHINE: WARRIOR 1800
Page 99
NAME: EXTENDED COLLECTION CONVEYOR MACHINE: WARRIOR 1800
1 12130810 0 EXTENDED COLLECTION CONVEYOR LINKAGE 4
2 12130820 0 CONVEYOR SUPPORT ARMS 1
3 15560110 0 RAM 2
4 12130815 0 EXTENDED COLLECTION CONVEYOR RAM SUPPORT 1
5 12330362 0 SUPPORT FRAME MOUNTING BRACKETS 2
[Figure End]
Page 100
NAME: COLLECTION CONV (RADIAL) DRIVE DRUM MACHINE: WARRIOR 1800
Page 101
1 12330311 1 COLLECTION CONVEYOR UPPER 1
2 12330312 0 MOTOR MOUNTING LH 1
3 12330313 0 HEADDRUM MOUNTING PLATE LH 1
6 03220103 0 ROLLER 3

(INTERCHANGEABLE)
8 06630310 0 DRIVE DRUM 1
9 03210165 0 TAPERLOCK 2
11 06630318 0 COLLAR 2
12 02020165 0 ROUND END KEY 2
13 02020163 0 TAPERLOCK 1
14 17630401 0 RM25 RIGID COUPLING 1
15 02220220 0 TAPERLOCK 1
17 12330317 0 DEFLECTOR PLATE RH 1
18 12330318 0 DEFLECTOR PLATE LH 1

REPLACES 12270157
21 17630266 0 MOTOR TORQUE ARM 1
22 17630267 0 TORQUE ARM GUARD 1
23 12330316 0 BRETBY GUARD 1
24 12330328 0 COLL CONV HEAT SHIELD 1
25 12330315 1 COLLECTION CONV CHUTE 1
26 12330323 0 CHUTE RUBBER 1
27 06930139 0 TENSIONER 2
28 12330340 0 BELT SCRAPPER FRAME 1
Page 102
29 12330341 0 COLL CONV SCRAPER RUBBER 1
30 12330342 0 COLL CONV SCRAPER FRAME MOUNTING ANGLE 2
31 12330343 0 COLL CONV SCRAPER CLAMP 1
[Figure End]
Page 103
Page 104
NAME: COLLECTION CONV (RADIAL) TAIL DRUM MACHINE: WARRIOR 1800
Page 105
1 12330350 0 COLLECTION CONVEYOR BELT 1
2 12330310 0 COLLECTION CONVEYOR LOWER 1
4 12230395 0 COLLECTION CONVEYOR TAIL BRACE 1
5 06930243 0 ADJUSTER ROD 2
6 09900405 0 TNP2" 3 BEARING 2
7 12230315 0 TAIL DRUM 1
8 02020163 0 TAPERLOCK 2
10 02020165 0 ROUND END KEY 2
12 12230320 0 DRUM SCRAPER 12
14 12230323 0 BELT CLEANER 1
15 12230322 0 STRAP 2
16 12330314 0 RADIAL FEEDBOOT 1
20 12330339 0 COLL CONV SKIRTING RUBBER 2
22 12330327 0 SKIRTING END RUBBER 2
23 12270151 0 SIDE GUARD RH 1
24 12270152 0 SIDE GUARD LH 1
25 12270153 0 REAR GUARD 1
27 12230680 0 ROLLER 18
Page 106
REPLACES 12270157
30 12270159 0 SIDE GUARD 6
34 03220103 0 ROLLER 2
37 12330319 0 LOWER DEFLECTOR RH 1
38 12330320 1 LOWER REFLECTOR LH 1
[Figure End]
Page 107
Page 108
NAME: TROUGHED COLLECTION CONVEYOR MACHINE: WARRIOR 1800
ILLUSTRATION:
Page 109
ILLUSTRATION:
1 12330380 0 COLLECTION CONVEYOR FRAME 1
1 12330386 0 COLLECTION CONVEYOR FRAME (REVERSE) 1
2 12231327 0 M24 X 600MM LG BELT ADJUSTER ROD 2
3 12231305 0 COLLECTION CONVEYOR TAIL DRUM ADJUSTER 2
4 00024001 0 NUT 2
5 12230304 0 COLLECTION CONV MOUNTING BRACKET 6
6 12230550 0 SCRAPER RUBBER CLAMP 2
9 12231310 0 COLLECTION CONVEYOR TAILDRUM SCRAPER 1
10 12230315 0 TAIL DRUM 1
11 09900405 0 TNP2" 3 BEARING 2
12 12231315 0 CONVEYOR FRAME BRACE 1
13 12270301 0 COLLECTION CONVEYOR REAR SIDE GUARD LH 1
14 12270300 0 COLLECTION CONVEYOR REAR GUARD 1
15 12270302 0 COLLECTION CONVEYOR REAR SIDE GUARD RH 1

REPLACES 12270157
18 02020163 0 TAPERLOCK 2
20 02020165 0 ROUND END KEY 2
22 12231330 0 COLLECTION CONV DRUM ADJUSTER SHOE 2

FROM SERIAL NO. 648220 ECO11182
UP TO SERIAL NO. 648219 ECO11182
(Interchangeable)
Page 110
ILLUSTRATION:
26 02020163 0 TAPERLOCK 2
27 12230310 0 DRIVE DRUM 1
29 02020211 0 TAPERLOCK 1
30 17630401 0 RM25 RIGID COUPLING 1
31 17630268 0 TORQUE ARM GUARD 1
32 03510164 0 TAPERLOCK 1
33 12330385 0 OMT MOTOR TORQUE ARM (REVERSE) 1
33 17630265 0 OMT MOTOR TORQUE ARM 1
35 12230354 0 BLADE SCRAPER FRAME 1
37 12230350 0 BELT CLEANER 1
39 12270158 0 HEAD DRUM GUARD 1
40 02020609 0 RH SIDE ROLLER 12
41 15830202 0 ROLLER 12
42 02020608 0 LH SIDE ROLLER 12
43 12270305 0 TAIL DRUM ADJUSTER GUARD 2
44 02020165 0 ROUND END KEY 4
45 12011131 0 RUBBER CLAMP (80MM) 8
47 12270306 0 SKIRTING ACCESS DOOR SMALL 2
49 03210361 0 FASTENER 2
50 12330381 0 COLLECTION CONV SKIRTING RH 1
51 12330383 0 COLLECTION CONVEYOR SKIRTING RUBBER 2
56 12231325 0 SKIRTING REAR RUBBER 1
Page 111
ILLUSTRATION:
57 12231322 0 SKIRTING BACK PLATE 1
58 12270303 0 SKIRTING ACCESS GUARD LARGE 2
59 12330336 0 FEEDBOOT EXTEN LH 1
60 12330335 0 FEEDBOOT EXTEN RH 1
61 12330338 0 FEEDBOOT EXTENSION SUPPORT LH 1
62 12330337 0 FEEDBOOT EXTENSION SUPPORT 1
63 12330382 0 COLLECTION CONV SKIRTING LH 1
64 12231301 0 BOLT-ON FRAME ADJUSTER 1
65 12230397 0 HEAD DRUM MTG PLATE RH 1

REPLACED BY 12330822 FROM SN 12305274
65 12330822 0 HEAD DRUM MTG PLATE RH 1
NEW FROM SN 12305274
66 12330820 0 BELT BLADE SCRAPER FRAME 1
UP TO SN 12305274
66 12330821 0 COLLECTION BLADE FRAME 1
66 12230396 0 BELT SCRAPER FRAME 1
UP TO SN 12305274
67 12530268 0 SCRAPER ADJUSTER BOLT 2
69 12330823 0 HEAD DRUM MTG PLATE LH 1

69 12230398 0 HEAD DRUM MTG PLATE LH 1
REPLACED BY 12330823 FROM SN 12305275
70 15680052 0 SPRING 2
71 00020002 0 LOCKNUT 2
[Figure End]
Page 112
NAME: DEUTZ CANOPY (TIER III) MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 06-13 REV: E
55
Page 113
ILLUSTRATION:
1 12990200 8 CH1700 POWERUNIT BASE FRAME 1
2 12990220 0 CH1700 POWERUNIT HYD TANK COVER 1
3 15820137 0 CANOPY RUBBER 1
4 12990210 8 POWERUNIT CANOPY 1
5 12990216 0 CH1700 P-UNIT COOLER ACCESS PANEL 1
6 12990215 0 CH1700 POWERUNIT CANOPY CUT-OUT 1

UP TO S/N
7 12990270 0 CH1700 POWERUNIT LH ACCESS DOOR 1
USED ON M/C SERIAL NUMBERS UP TO:12305182
7 12990279 0 POWERUNIT LH ACCESS DOOR (FA PARKES DR 1
HANDLE)
USED ON M/C SERIAL NO: 12305183
8 12990251 0 CH1700 2013 PUNIT AIR DISCHARGE GUARD 1
9 12990248 0 CH1700 POWERUNIT ENGINE AIR DISCHARGE PL 2013 1
10 12990265 0 CH1700 POWERUNIT RH LARGE DOOR DEFLECTOR 1
11 12990261 0 CH1700 2013 PUNIT RH LARGE SIDE DOOR 1

11 12990271 0 CH1700 2013 ECF PUNIT RH LARGE SIDE DOOR 1

ORDER ITEM 11, PART NO. 12990271 ECO11235
12 12990214 0 CH1700 2013 PUNIT CANOPY SUPPORT 1
13 12990267 0 CH1700 PUNIT RH SMALL SIDE DOOR 1

13 12990258 1 CH1700 2013 ECF PUNIT RH SMALL SIDE DOOR 1
14 12990277 0 CH1700 2013 PUNIT BATTERY BOX 1
15 12990276 0 CH1700 POWERUNIT BATTERY STRAP 1
16 12990225 0 CH1700 POWERUNIT REAR ACCESS PANEL 1
17 12990327 0 PLASTIC ROUND INSERT - 102MM OD PIPE 1

REPLACES 12990221 FROM S/N 12305279
18 12990240 0 CH1700 POWERUNIT RETURN LINE MANIFOLD 1
19 12990212 0 CH1700 P-UNIT CONTROL PANEL MTG BRK 1
20 12990205 2 CH1700 POWERUNIT HYD TANK CRADLE 1
21 12290337 1 EXHAUST SILENCER 1

UP TO S/N
22 12990326 0 OIL COOLER PUSHER 1
23 12390250 0 EXHAUST HEAT SHIELD 1
UP TO S/N
24 03210237 0 BATTERY 1
25 12290155 0 BATTERY ISOLATOR SWITCH 1
Page 114
ILLUSTRATION:
26 10412390310 0 WR1800 DEUTZ 2013 TRANSVERSE P-UNIT ELECTRIC 1

KIT
27 06790420 0 SIREN 1
28 06590276 0 EMERGENCY STOP COMPLETE 2
29 09499104 0 STAIN/STEEL HINGE 4
30 09499108 0 STAINLESS STEEL HINGE 2
31 02030475 0 M12 ANTI-LUCE FASTENER 2
32 02280109 0 ADAPTOR 6
33 05060157 0 ADAPTOR 2
36 03260195 0 CHECK VALVE 1
37 03260392 0 PLASTIC BODY 4
38 01950204 0 HINGE PIN BOLT ON 2
39 02060216 0 DOWTY SEAL 4
40 12390252 0 FEEDER UNDER TRAY POWERUNIT STAND 1
42 12290176 0 DOOR HANDLE 2

42 12290179 0 POWERUNIT DOOR HANDLE (FA PARKES) 2
43 12990303 0 PUNIT RUBBER FLAP STRAP 1
44 12990325_001 0 COVER PLATE 2

FROM S/N 12305279
45 12490390 0 DEUTZ 2013 PUNIT CANOPY CUT-OUT 1
FROM S/N
46 12490391 0 DEUTZ 2013 PUNIT CANOPY EXTENSION 1
FROM S/N
47 12490392 0 DEUTZ 2013 PUNIT SILENCER LOCATING PL 1
FROM S/N
48 12462582 0 CHECK VALVE TO CANOPY LID PIPE 1
FROM S/N
49 12890222 0 SCAVENGE LINE CHECK VALVE 1
FROM S/N
50 12462581 0 EXHAUST EJECTOR TO CHECK VALVE 1
FROM S/N
51 13590422 0 EXHAUST TAIL PIPE 1
FROM S/N
52 12590159 1 EXHAUST EJECTOR 1
FROM S/N
53 12490398 0 EXHAUST 1
FROM S/N
54 12490396 0 EXHAUST PIECE 1
FROM S/N
55 12990259 1 CH1700 2013 ECF PUNIT RH SMALL SIDE 1
Page 115
ILLUSTRATION:
[Figure End]
Page 116
NAME: HYDRAULIC TANK (TIER III) MACHINE: WARRIOR 1800
ILLUSTRATION: POWERUNIT
Page 117
1 12990280 2 CH1700 POWERUNIT HYDRAULIC TANK 1
2 03310228 0 HYD TANK LID GASKET 1
3 12990283 0 HYDRAULIC TANK ACCESS LID 1
4 12990281 0 Gasket 1
5 12990282 0 HYD TANK FILLER PLATE 1
6 01800275 0 SOLENOID BLOCK COMPLETE 1
7 02012116 0 LOCKABLE FILLER CAP 1
8 03260228 0 FILTER UNIT 1
9 02010518 0 LEVEL GAUGE 1
10 12290156 0 OIL LEVEL SWITCH 1
11 06760105 0 SUCTION ELEMENT 1
13 06760107 0 ADAPTOR 1
14 06760106 0 ADAPTOR 1
15 12990284 0 2" BSP MALECAP 1
16 03260145 0 ADAPTOR 5
17 03260146 0 ADAPTOR 2
18 03260275 0 ADAPTOR 1
19 02060206 0 ADAPTOR 1
20 02060207 0 1" ADAPTOR MALECAP STOPPER 1
22 02280109 0 ADAPTOR 2
23 02060204 0 ADAPTOR 2
24 01190116 0 BALL VALVE 1
25 01190115 0 BALL VALVE 2
26 02110539 0 ADAPTOR 1
27 02010536 0 ADAPTOR 1
28 06760108 0 DOWTY SEAL 2
29 03260144 0 DOWTY SEAL 3
30 02060217 0 DOWTY SEAL 3
Page 118
31 02060216 0 DOWTY SEAL 16
32 03260392 0 PLASTIC BODY 4
[Figure End]
Page 119
Page 120
NAME: VALVE BANK (TIER III) MACHINE: WARRIOR 1800
17
13
18
10
9
16
5
8
17
20
7
1
4
9
24
11
21
19
13
14
18
11
3
2
15
19
12
6
23
17
OPTION
22
Page 121
1 12990230 2 POWERUNIT CONTROL PANEL PLATE 1
2 12990235 0 CH1700 POWERUNIT CONTROL PANEL PLATE COVER 1
3 12260165 0 CONTROL VALVE(5 BANK Supersedes 15560140 1

19/02/04 (Non Interchangeable)
4 12090363 0 CONTROL VALVE 4
6 03220115 0 2FV2V250J FLOW CONTROL VALVE 3
7 02280109 0 ADAPTOR 2
8 17090165 0 3/4" TEST POINT VALVE 5
10 01920376 0 ADAPTOR 1
11 02060202 0 02060215 2
12 02060442 0 ADAPTOR 1
13 02060285 0 02060285 2
14 02060231 0 ADAPTOR 10
15 12260167 0 ADAPTOR 1
16 02060256 0 ADAPTOR 2
17 02060216 0 DOWTY SEAL 29
18 02060215 0 02060215 3
19 02060218 0 DOWTY SEAL 12
20 13260150 0 NORMALLY OPEN SOLENOID VALVE S612NH126WTSM 1

FROM S/N 12305230
FROM S/N 12305230
21 06690945_001 0 CONVEYOR START DELAY SENSOR MTG BRK 1
FROM S/N 12210352
22 60501016 0 REMOTE OPERATOR SYSTEM 4 CHANNEL 12/24VDC 1
COMPLETE
(OPTION) FROM S/N PID00123HDGB52870
22 REMOTE_SS_FEEDER_BO 0 REMOTE START/STOP FEEDER BOX 1

X
(OPTION)
23 12290790 0 FEEDER REMOTE START/STOP MTG BRACKET 1

(OPTION)
23 12290791 0 12290791 1
(OPTION) FROM S/N PID00123HDGB52870
24 60541010 0 PROXIMITY SWITCH INDUCTIVE M12 RANGE 4MM 1
Page 122
[Figure End]
Page 123
Page 124
NAME: DEUTZ 2013 (TIER III) MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 06-16 REV: D
Page 125
ILLUSTRATION:
1 06690800 0 2013 DEUTZ TIER 3 ENGINE - 4 CYLINDER 1
2 12990206 0 CH1700 2013 PUNIT ENGINE SUPPORT 4
3 12990287 0 CH1700 P-UNIT DEUTZ FUEL FILTER MOUNTING BRK 1
4 12990286 0 CH1700 P-UNIT DEUTZ WATER TRAP MTG BRK 1
5 12990292 0 CH1700 2013 P-UNIT AIR FILTER MTG BRK 1

UP TO S/N
6 12390253 0 DEUTZ 2013 P-UNIT EXHAUST PIECE 1
FROM S/N 12305172 - UP TO S/N
6 12390251 0 WARRIOR 2013 TRANSVERSE P-UNIT EXHAUST PIECE 1
UP TO S/N 12305171
7 12990299 0 CH1700 2013 EXHAUST FLANGE 1
UP TO S/N
8 05790251 0 EXHAUST BELLOW 1
UP TO S/N
9 06690296 0 PUMP 1
10 01800240 0 BEND 1
11 12090373 0 TRIPLE PUMP 1

MOUNT USING M12 X 50 BOLTS
12 07290362 0 PUMP MTG PLATE 1
13 07290361 0 HUB 1
14 05790360 0 FLANGE PLATE 1
15 17090256 0 FUEL FILTER 2
16 17090255 0 WATER TRAP 1

UP TO ENG SERIAL 10913553
16 06690991 0 DEUTZ TCD2012L04M FUEL PREFILTER CARTRIDGE 1
(0211-3831)
FROM ENG SERIAL 10913553
16 06690992 0 DEUTZ TCD2012L06/TCD2013L04 FUEL PREFILTER 1

(0450-4439)
FROM ENG SERIAL 10913553
17 12990293 0 CH1700 2013 P-UNIT PRE CLEANER PIPE 1

UP TO S/N
18 05790476 0 90 DEGREE BEND 1
19 17090158 0 AIR BREATHER 4" SS 90DEG BEND 1
20 12990300 0 CH1700 2013 AIR INTAKE PIPE 1

UP TO S/N
21 05790455 0 AIR FILTER COMPLETE 1
UP TO S/N
22 05790456 0 FILTER RETAINER 1
UP TO S/N
23 05790466 0 SAFETY ELEMENT 1
UP TO S/N
24 05790461 0 AIR FILTER ELEMENT 1
UP TO S/N
25 05790457 0 DUST EJECTOR 1
UP TO S/N
Page 126
ILLUSTRATION:
26 06590339 0 BULLNOSE PRE-CLEANER 1

UP TO S/N
28 03260253 0 PUMP ADAPTOR 1
30 02060227 0 SCREW 4
31 03260146 0 ADAPTOR 1
32 06760110 0 PUMP ADAPTOR 1
34 06760119 0 BOLT M12 4
35 06760107 0 ADAPTOR 1
36 06760108 0 DOWTY SEAL 1
37 03260144 0 DOWTY SEAL 1
38 02060216 0 DOWTY SEAL 5
39 06760116 0 O-RING 1
40 05190136 0 O-RING 1
41 06590206 0 OIL FILTER 1

NOT SHOWN IN FIGURE
42 12490376 0 DEUTZ 2013 P-UNIT EXHAUST PIECE 1
FROM S/N 12305172 - UP TO S/N
43 06690836 0 EXHAUST HEAT DEFLECTOR 1
UP TO S/N
44 06690802 0 DEUTZ TCD2013L04 FAN BELT - 0118 1730 1
NOT SHOWN IN FIGURE
45 12490450 0 DONALDSON PSD09 FILTER 1
FROM S/N
46 12490451 0 DONALDSON PSD09 FILTER (D090053) PRIMARY 1
ELEMENT
FROM S/N
47 12490452 0 DONALDSON PSD09 FILTER (D090053) SAFETY 1

ELEMENT
FROM S/N
48 12890223 0 SCAVENGE LINE ADAPTOR 1

FROM S/N
49 12490393 0 DEUTZ 2013 DONALDSON AIR INTAKE PIPE 1
FROM S/N
FROM S/N
FROM S/N
52 12490394 0 EXHAUST FLANGE 1
FROM S/N
[Figure End]
Page 127
Page 128
NAME: CAT CANOPY (TIER III) MACHINE: WARRIOR 1800
ILLUSTRATION:
45
Page 129
ILLUSTRATION:
1 12990200 8 CH1700 POWERUNIT BASE FRAME 1
2 12990220 0 CH1700 POWERUNIT HYD TANK COVER 1
3 15820137 0 CANOPY RUBBER 1
4 12990210 8 POWERUNIT CANOPY 1
5 12890225 0 P-UNIT ACCESS PANEL C/W SCAVENGE LINE 1

CONNECTION
UP TO SERIAL NO -
6 12990215 0 CH1700 POWERUNIT CANOPY CUT-OUT 1
7 12990279 0 POWERUNIT LH ACCESS DOOR (FA PARKES DR 1

HANDLE)
7 12990270 0 CH1700 POWERUNIT LH ACCESS DOOR 1

USED ON M/C SERIAL NUMBERS UP TO: 12305182
8 12990250 0 CH1700 POWERUNIT AIR DISCHARGE GUARD 1
9 12990245 0 CH1700 POWERUNIT ENGINE AIR DISCHARGE PLATE 1
10 12990265 0 CH1700 POWERUNIT RH LARGE DOOR DEFLECTOR 1

11 12990271 0 CH1700 2013 ECF PUNIT RH LARGE SIDE DOOR 1
11 12990260 0 CH1700 POWERUNIT RH LARGE SIDE DOOR 1

12 12990211 0 CH1700 POWERUNIT CANOPY SUPPORT 1
13 12990255 1 CH1700 POWERUNIT RH SMALL SIDE DOOR 1

UP TO S/N TBD
13 12990258 1 CH1700 2013 ECF PUNIT RH SMALL SIDE DOOR 1
13 12990267 0 CH1700 PUNIT RH SMALL SIDE DOOR 1

14 12990277 0 CH1700 2013 PUNIT BATTERY BOX 1
15 12990276 0 CH1700 POWERUNIT BATTERY STRAP 1
16 12990225 0 CH1700 POWERUNIT REAR ACCESS PANEL 1
17 12990327 0 PLASTIC ROUND INSERT - 102MM OD PIPE 1

18 12990240 0 CH1700 POWERUNIT RETURN LINE MANIFOLD 1
19 12990212 0 CH1700 P-UNIT CONTROL PANEL MTG BRK 1
20 12990205 2 CH1700 POWERUNIT HYD TANK CRADLE 1
21 12890170 0 EXHAUST SILENCER WITH EJECTOR 1

UP TO S/N TBD
21 12490380 0 EXHAUST WITH EJECTOR 1
Page 130
ILLUSTRATION:

23 12390250 0 EXHAUST HEAT SHIELD 1
24 03210237 0 BATTERY 1
26 10412390311 0 P-UNIT ELECTRIC KIT (83KW) 1
27 06790420 0 SIREN 1
29 09499104 0 STAIN/STEEL HINGE 4
30 09499108 0 STAINLESS STEEL HINGE 2
31 02030475 0 M12 ANTI-LUCE FASTENER 2
32 02280109 0 ADAPTOR 6
33 05060157 0 ADAPTOR 2
36 03260195 0 CHECK VALVE 1
37 03260392 0 PLASTIC BODY 4
39 02060216 0 DOWTY SEAL 4
40 12860753 0 ACCESS PANEL PIPE TO EXHAUST EJECTOR INLET 1

FROM KIT REF. 12860750
41 12390252 0 FEEDER UNDER TRAY POWERUNIT STAND 1
42 12290179 0 POWERUNIT DOOR HANDLE (FA PARKES) 2

42 12290176 0 DOOR HANDLE 2
43 12990303 0 PUNIT RUBBER FLAP STRAP 1
44 12990325_001 0 COVER PLATE 1

FROM S/N 12305279
45 12990259 1 CH1700 2013 ECF PUNIT RH SMALL SIDE 1
[Figure End]
Page 131
Page 132
NAME: CAT C4.4 83kW (TIER III) MACHINE: WARRIOR 1800
ILLUSTRATION:
Page 133
ILLUSTRATION:
1 12890203 0 CAT C4.4 PUSHER FAN ENGINE 83KW FOR HD AIR 1

FILTER
FROM S/N 12305245
1 12890204 0 CAT C4.4 PUSHER FAN ENGINE 83KW 1

UP TO S/N 12305244
2 12990286 0 CH1700 P-UNIT DEUTZ WATER TRAP MTG BRK 1
3 12990213 0 CAT C4.4 TANDEM SIDE PUMP MTG BRACKET 1

UP TO S/N 12305229
3 12490387 0 CAT C4.4 SIDE PUMP BASE MTG BRACKET 1
FROM S/N 12305230
4 12890221 0 DONALDSON PSD09 AIR FILTER BRACKET 1
FROM S/N 12305245
5 12890224 0 SCAVENGE LINE CHECK VALVE MTG BRACKET 1
FROM S/N 12305245
6 12490383 0 WR1400 EXHAUST 1ST SECTION FLANGE 1
FROM S/N PID00123CDGBB3923 ECO11414
6 12290335 0 EXHAUST MTG 1
MACHINES UPTO S/N PID00123CDGBB3922 ORDER ITEM 6, PART NO.
12490383, ITEM 7, PART NO, 12490382 AND ITEM 8 13290140 ECO11414
7 12490382 0 P-UNIT EXHAUST 90 DEGREE SWEPT BEND 1

7 12490379 0 P-UNIT EXHAUST 90 DEGREE SWEPT BEND 1
8 13290140 0 FLEX CONNECTOR WITH TUBE ENDS 1

9 12890250 0 TANDEM SIDE PUMP 1
10 06690280 0 PUMP TRIPLE 1

11 09560200 0 MOUNTING PLATE 1
12 07290361 0 HUB 1
13 05790360 0 FLANGE PLATE 1
14 12290164 0 THROTTLE CABLE 1
15 12890227 0 AIR FILTER BRACKET SPACER 1

FROM S/N 12305245
16 12890220 0 AIR FILTER 1
FROM S/N 12305245
FROM S/N 12305245
18 12890226 0 AIR BREATHER PIPE 1
FROM S/N 12305245
19 12860751 0 AIR FILTER ADAPTOR TO CHECK VALVE INLET 1
FROM HOSE KIT REF. 12860750
20 12860752 0 CHECK VALVE OUTLET TO ACCESS PANEL PIPE 1
FROM HOSE KIT REF. 12860750
FROM S/N 12305245
22 02060239 0 TEE ADAPTOR 1
Page 134
ILLUSTRATION:
24 12290521 0 WATERSCAN ELEMENT 1
25 02060227 0 SCREW 4
27 03260146 0 ADAPTOR 1
28 17660109 0 90° FLANGE 1
29 06760110 0 PUMP ADAPTOR 1
31 06760119 0 BOLT M12 4
32 06760107 0 ADAPTOR 1
33 01800240 0 BEND 1
34 06760108 0 DOWTY SEAL 1
35 03260144 0 DOWTY SEAL 1
36 02060216 0 DOWTY SEAL 5
37 05190136 0 O-RING 1
38 06760116 0 O-RING 1
39 12360140 0 16MM DOUBLE CLAMP COMPLETE 1
40 12890205 0 AIR FILTER, COMPLETE 1

UP TO S/N 12305244
41 12290402 0 OUTER FILTER ELEMENT 1
UP TO S/N 12305244
42 12290401 0 INNER FILTER ELEMENT 1
UP TO S/N 12305244
43 12290510 0 OIL FILTER ELEMENT 1
NOT SHOWN IN FIGURE
44 12890233 0 FUEL FILTER 1
NOT SHOWN IN FIGURE
45 12890228 0 DONALDSON PRT NO P607542 1
FROM S/N 12305245
FROM S/N 12305245
47 06690981 0 HEAVY DUTY CLAMP CT450L 1
FROM S/N 12305245
48 06690980 0 HEAVY DUTY CLAMP CT300L 1
FROM S/N 12305245
49 17690205 0 AIR BLOCKAGE INDICATOR 1
50 12490388 0 CAT C4.4 TANDEM SIDE PUMP MTG BRACKET 1

FROM S/N 12305230
51 12490386 0 CAT C4.4 SIDE PUMP MIDDLE MTG BRACKET 1
FROM S/N 12305230
52 12890216 0 CAT C4.4 FAN BELTS - 2614B953 1
2 BELTS SUPPLIED UNDER PRT NO - NOT SHOWN IN FIGURE
53 06690928 0 CAT C4.4 EXTENDED DIPSTICK 1
UPTO SERIAL NO. 44410649, ECO11404
Page 135
ILLUSTRATION:
53 06690941 0 CAT C4.4 EXTENDED DIPSTICK - ENG SERIAL 1

44410650
FROM SERIAL NO. 44410650, ECO11404
54 06690924 0 CAT C4.4 EXTENDED DIPSTICK PIPE 1

FROM S/N
55 01900495 0 13-20 JUBILEE CLIP 1
FROM S/N
56 06690929 0 M16 X 12MMODX30MM STEM HOSETAIL 1
FROM S/N
57 02060218 0 DOWTY SEAL 1
FROM S/N
58 00012006 0 WASHER 4
FROM S/N
FROM S/N
60 00012030 0 BOLT M12 4
FROM S/N
[Figure End]
Page 136
NAME: QUAD PUMP COLLECTION/FINES SPLIT (TIER III) MACHINE: WARRIOR 1800
ILLUSTRATION:
Page 137
NAME: QUAD PUMP COLLECTION/FINES SPLIT (TIER III) MACHINE: WARRIOR 1800
ILLUSTRATION:
1 12990238 0 CAT C4.4 QUAD PUMP MTG BRK 46/46/33/33 1

12990238 ON CAT ENG / 12990234 DEUTZ ENG OP TO S/N
2 12990233 0 ECF VALVE MTG BRACKET 1
3 12460141 0 PUMP XIA 46/46/32.3/32.3 1

MOUNT USING M12X50 BOLTS
09560200 ON CAT ENGINE / 05790367 ON DEUTZ ENGINE. MOUNT USING
M12X30 BOLTS
5 17090111 0 BOWEX 65T 1!/4" PARALLEL PUMP HUB 1
6 05790365 0 FLANGE PLATE 1
9 03260146 0 ADAPTOR 3
10 02060206 0 ADAPTOR 1
12 01920376 0 ADAPTOR 3
13 02060256 0 ADAPTOR 1
14 03260144 0 DOWTY SEAL 3
15 02060216 0 DOWTY SEAL 1
16 02060216 0 DOWTY SEAL 10
17 12990341 0 QUAD PUMP CENTRE MTG BRK 1

FROM S/N
18 12990340 0 QUAD PUMP ENG MTG BRK 1
FROM S/N
19 12990342_001 0 QUAD PUMP MTG BRK 1
FROM S/N
20 00012001 0 NUT 4
FROM S/N
21 00012006 0 WASHER 8
FROM S/N
22 00012040 0 BOLT M12 4
FROM S/N
[Figure End]
Page 138
NAME: DUAL POWER OPTION MACHINE: WARRIOR 1800
ILLUSTRATION:
Page 139
ILLUSTRATION:
1 12320126 0 W1800 DUAL POWER BOLT-ON TRACK CHASSIS 1
2 12320352 0 DUAL POWER FLOOR GUARD 1
3 12320350 0 OUTER LANDING LEG 2
4 06620387 0 JACKING LEG PIN 2
5 12320351 0 JACKING LEG INNER 2
6 12290707 0 DUAL POWER CONTROL PANEL HINGE 1
7 06980110 0 PIN 1
8 12290708 0 WARRIOR DUAL POWER CONTROL PANEL MTG BRK 1
9 22020179 0 ANTI VIBRATION MOUNT 4
10 22020180 0 ANTI VIBRATION MOUNT 2
11 12290706 0 DUAL POWER CONTROL PANEL HINGE POST 1
12 12390350 0 DUAL POWER MOUNT 1
13 12390352 0 DUAL POWER LOWER LID 1
14 07290508 0 50HP ELEC MOTOR (FLA 2
15 12390320 0 50HP BELL HOUSING SAE-127-4 BOLT 1 1/4" PARALLEL 1

USED ON (63/41/41 PUMP)
15 12490315 0 BELL HOUSING 1
16 17060130 0 PUMP TRIPLE 1
17 02060216 0 DOWTY SEAL 6
19 02110539 0 ADAPTOR 1
20 06760110 0 PUMP ADAPTOR 1
21 06760119 0 BOLT M12 4
23 06760108 0 DOWTY SEAL 4
24 06760106 0 ADAPTOR 1
25 12390351 0 DUAL POWER TOP LID 1
26 09520127 0 TRIPLE PUMP 1
27 03260253 0 PUMP ADAPTOR 3
29 02060227 0 SCREW 12
Page 140
ILLUSTRATION:
30 03260144 0 DOWTY SEAL 12
31 03260146 0 ADAPTOR 9
32 12490313 0 DUAL POWER 2" SUCTION MANIFOLD 1
33 12490314 0 DUAL POWER 1 1/2" SUCTION MANIFOLD 3
34 01800240 0 BEND 1
35 12490317 0 ADAPTOR 1
36 01800162 0 ADAPTOR 3
37 12330169 0 DUAL POWER POWERUNIT EXTENSION 1
[Figure End]
Page 141
Page 142
NAME: RADIATOR CAP ACCESS MACHINE: WARRIOR 1800
ILLUSTRATION:
Page 143
NAME: RADIATOR CAP ACCESS MACHINE: WARRIOR 1800
ILLUSTRATION:
1 12990380 0 CAT C4.4 RADIATOR COVER ASSEMBLY 1

CAT ENGINE
2 12990382 0 DEUTZ RADIATOR COVER ASSEMBLY 1
DEUTZ ENGINE
3 12990381 0 RADIATOR COVER ASSEMBLY LID 1
4 12_86_3029 0 12_86_3029 1
5 00006020 0 BOLT M06 4
6 00006006 0 WASHER 4
7 12_10_0031M 0 12_10_0031M 1
8 00006001 0 NUT 4
9 12990383 0 5/16-24UNF NYLOC NUT G8 ZY 2
10 00010035 0 BOLT M10 4
11 02010625 0 M10 SPRING WASHER 4
12 12990243 0 PUNIT COOLER ACCESS BEADING 1
[Figure End]
Page 144
NAME: TIER 4i POWERUNIT CANOPY LAYOUT MACHINE: WARRIOR 1800
ILLUSTRATION:
D
E
C
B
A
G
H
Page 145
NAME: TIER 4i POWERUNIT CANOPY LAYOUT MACHINE: WARRIOR 1800
ILLUSTRATION:
[Figure End]
Page 146
NAME: TIER 4i POWER UNIT ROOF MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 06-22-A REV: A
7
3
8
A
4
B B
5
B
A
9
1
6
17
16
11
C
15
8
7
D
C
12
13
14
10
Page 147
NAME: TIER 4i POWER UNIT ROOF MACHINE: WARRIOR 1800
ILLUSTRATION:
1 12990637 1 EXHAUST VENTURI COVER 1
2 12990654 1 TIER4 PUNIT PROTECTIVE RUBBER STRAP 2
3 00010030 0 BOLT M10 4
4 00010006 0 M10 WASHER 4
5 12390503 2 WR1800 TIER4 POWERUNIT PROTECTIVE RUBBER 1
6 12990602 0 TIER4 PUNIT REMOVABLE ROOF PANEL 1
7 00012030 0 BOLT M12 18
8 00012006 0 WASHER 18
9 12990750 2 TIER 4 POWERUNIT ROOF 1
10 M16_LIFTIN_EYE-SCREW 0 M16 LIFTING EYE - SCREW 2
11 12390260 1 FEEDER UNDER TRAY T4 POWERUNIT STAND 1
12 00012035 0 M12X035 SETSCW8.8ZP 6
14 02020175 0 WASHER 6
15 12390361 1 FEEDER UNDER TRAY T4 POWERUNIT STAND 1

RUBBER
16 12990751 0 TIER4 PUNIT REMOVABLE ROOF PANEL 1
17 12390502 0 WR1800 STRAIGHT EXHAUST PIECE 1
[Figure End]
Page 148
NAME: TIER 4i POWER UNIT BATTERY MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 06-22-B REV: A
2
5
A
4
A
Page 149
NAME: TIER 4i POWER UNIT BATTERY MACHINE: WARRIOR 1800
ILLUSTRATION:
1 03210237 0 BATTERY 1
2 12990639 0 TIER4 POWERUNIT BATTERY MTG PLATE 1
3 00006025 0 BOLT M06 4
4 12.10.0031 0 JAGGER STEEL HINGE 1
5 12990619 0 TIER4 PUNIT BATTERY STRAP 1
[Figure End]
Page 150
NAME: TIER 4i OIL COOLER MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 06-22-C REV: A
4
3
8
5
6
2
1
Page 151
NAME: TIER 4i OIL COOLER MACHINE: WARRIOR 1800
ILLUSTRATION:
1 02060216 0 DOWTY SEAL 2
2 05060157 0 ADAPTOR 2
4 12463140 0 PUNIT BULKHEAD TO OIL COOLER 1
5 12463131 0 OIL COOLER BYPASS 1
7 check_valve 1 CHECK VALVE 1
8 12463132 0 OIL COOLER TO RETURN LINE MANIFOLD 1
[Figure End]
Page 152
NAME: TIER 4i POWER UNIT FRONT DOOR RHS MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 06-22-D.1 REV: A
4
2
5
6
7
11
10
12
A
9
A
8
Page 153
NAME: TIER 4i POWER UNIT FRONT DOOR RHS MACHINE: WARRIOR 1800
ILLUSTRATION:
1 17620119 0 SLOTTED HINGE EYE 2
2 00012006 0 WASHER 8
3 00012035 0 M12X035 SETSCW8.8ZP 4
4 12990709 0 SOUTHCO DOOR LATCH 1
5 12990747 0 JUMP START CONNECTOR COVER 1
6 00010006 0 M10 WASHER 4
7 00001025 0 m10x25 bolt 4
8 00006002 0 LOCKNUT 4
9 00006006 0 WASHER 4
10 12990746 1 TIER4 PUNIT AIR INLET DOOR 1
11 00012002 0 LOCKNUT 4
12 12990718 0 TIER4 PUNIT ACCESS DOOR - DOOR STAY 1
[Figure End]
Page 154
NAME: TIER 4i POWER UNIT FRONT DOOR POST MACHINE: WARRIOR 1800
ILLUSTRATION:
7
2
5
1
6
3
8
11
12
13
10
Page 155
NAME: TIER 4i POWER UNIT FRONT DOOR POST MACHINE: WARRIOR 1800
ILLUSTRATION:
1 00012006 0 WASHER 8
2 00012030 0 BOLT M12 4
4 12990744 1 TIER4 REMOVABLE LH SIDE POST 1
6 01920284 0 BOLT M08 4
7 60552307 0 CAT 4.4 T4 CONTROL PANEL 1

FOR INTERNALS BREAKDOWN SEE FIG 06-24-A
8 00012035 0 M12X035 SETSCW8.8ZP 2
9 00012002 0 LOCKNUT 7
10 05190370 0 THROTTLE KIT 1
11 00008006 0 WASHER 12
12 00008002 0 LOCKNUT 4
13 60545004 0 LED POWERUNIT LAMP 1
[Figure End]
Page 156
NAME: TIER 4i POWER UNIT DOOR FRONT LHS MACHINE: WARRIOR 1800
ILLUSTRATION:
10
3
11
A
4
2
9
8
7
1
A
5
12
13
14
15
Page 157
NAME: TIER 4i POWER UNIT DOOR FRONT LHS MACHINE: WARRIOR 1800
ILLUSTRATION:
1 00006002 0 LOCKNUT 20
2 00006002 0 LOCKNUT 80
3 00006025 0 BOLT M06 20
5 00012002 0 LOCKNUT 5
7 00012006 0 WASHER 4
8 00012035 0 M12X035 SETSCW8.8ZP 4
9 12990741 0 TIER4 PUNIT CONTROL VALVE ACCESS DOOR 1
10 12990742 1 TIER4 PUNIT CONTROL PANEL ACCESS DOOR 1
11 12.86.3029 0 VISE ACTION COMP. LATCH 2
13 12990740 1 TIER4 PUNIT RHS ACCESS DOOR 1
14 02020529 0 BOLT M12 2
15 12990743 0 TIER4 PUNIT ACCESS DOOR - DOOR STAY 1
[Figure End]
Page 158
NAME: TIER 4i VALVE BLOCK LAYOUT MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 06-22-E REV: A
5
3
2
4
1
8
6
7
9
Page 159
NAME: TIER 4i VALVE BLOCK LAYOUT MACHINE: WARRIOR 1800
ILLUSTRATION:
2 12990604 1 TIER4 PSCREEN POWERUNIT CONTROL PANEL 1

PLATE
4 03260316 1 PRESSUR RELIEF VALVE 1
5 12990605 1 POWERUNIT CONTROL PANEL PLATE COVER 1

7 12990663 0 P-UNIT V-GRID/ MAIN CONV SLIDE BALL VALVE 1

WITH PROXIMITY SWITCH SEE VALVE 5 FIF 06-22-E.5
[Figure End]
Page 160
NAME: TIER 4i SDM140 VALVE BLOCK 1 MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 06-22-E.1 REV: A
4
3
5
2
1
9
8
7
12
10
13
11
Page 161
NAME: TIER 4i SDM140 VALVE BLOCK 1 MACHINE: WARRIOR 1800
ILLUSTRATION:
1 02060216 0 DOWTY SEAL 3
3 17090165 1 TEE TEST POINT PORT 1
4 17090166 0 1/8" TEST POINT VALVE 1
5 12361759 1 SIDE PUMP (23) TO TAIL CONV CV (P) 1
6 12361783 1 TAIL CV (B) TO PUNIT BULKHEAD 1
7 02060202 0 02060215 1
8 02060215 0 02060215 1
9 12361760 0 TAIL CONV CV (T) TO RETURN LINE MANIFOLD 1
10 65500102 0 SEAL KIT FOR CONTROL VALVE SDM140 1
11 12361769 0 TAIL CONV CV (CARRYOVER) TO AUXILLARY CV (P) 1
13 12090362 0 CONTROL VALVE HANDLE 1
[Figure End]
Page 162
NAME: TIER 4i SD14_VALVE_2 MACHINE: WARRIOR 1800
ILLUSTRATION:
5
4
7
3
2
9
1
10
11
Page 163
ILLUSTRATION:
2 02060216 0 DOWTY SEAL 4
3 17090166 0 1/8" TEST POINT VALVE 1
5 12361755 0 FLYWHEEL PUMP (33) TO COLLECTION CONV CV (P) 1
7 12361771 0 COLL CONV CV (B) TO PUNIT BULKHEAD 1
8 02060256 0 ADAPTOR 1
9 12361761 0 COLL CONV CV (T) TO RETURN LINE MANIFOLD 1
10 65501124 0 5GD05111001 SEAL KIT SD14/1 VALVE 1
[Figure End]
Page 164
ILLUSTRATION:
5
4
7
3
2
9
1
10
11
Page 165
ILLUSTRATION:
2 02060216 0 DOWTY SEAL 4
3 17090166 0 1/8" TEST POINT VALVE 1
5 12361758 1 SIDE PUMP (23) TO MIDS SIDE CONV CV (P) 1
7 12361770 0 MIDS CONV (B) TO MIDS CONV FLOW CONTROL (P) 1
8 02060256 0 ADAPTOR 1
9 12361762 0 MIDS CONV CV (T) TO RETURN LINE MANIFOLD 1
[Figure End]
Page 166
ILLUSTRATION:
5
4
7
3
8
2
9
1
10
11
12
Page 167
ILLUSTRATION:
2 02060216 0 DOWTY SEAL 4
3 17090166 0 1/8" TEST POINT VALVE 1
5 12361756 0 FLYWHEEL PUMP (46) TO SCREEN CONV CV (P) 1
6 02280109 0 ADAPTOR 1
7 12361784 0 SCREEN CV (B) TO PUNIT BULKHEAD 1
8 12361776 1 SCREEN CV (A) TO TRACK SOLENOID (P) 1
9 12361764 0 SCREEN CV (T) TO RETURN LINE MANIFOLD 1
[Figure End]
Page 168
NAME: TIER 4i SD14 WITH PROXIMITY VALVE 5 MACHINE: WARRIOR 1800
ILLUSTRATION:
7
6
5
4
3
8
2
9
17
10
15
1
11
16
14
12
13
Page 169
NAME: TIER 4i SD14 WITH PROXIMITY VALVE 5 MACHINE: WARRIOR 1800
ILLUSTRATION:
2 02060216 0 DOWTY SEAL 5
4 17090166 0 1/8" TEST POINT VALVE 1
5 12361797 0 FLYWHEEL PUMP (33) TO COLLECTION CV (P) 1
6 12463108 1 SIDE PUMP (23) TO LH SIDE CONV CV (P) 1
7 12361772 0 FINES CONV CV (B) TO FINES CONV FLOW CONTROL 1

(P)
9 05060157 0 ADAPTOR 1
10 12361763 0 DELAY SOLENOID (T) TO RETURN LINE MANIFOLD 1
11 12361765 0 FINES CONV CV (T) TO RETURN LINE MANIFOLD 1
12 12990624 0 CONVEYOR START DELAY SENSOR MTG BRK 1
13 60541010 0 PROXIMITY SWITCH INDUCTIVE M12 RANGE 4MM 1
15 02060256 0 ADAPTOR 1
17 02280109 0 ADAPTOR 1
[Figure End]
Page 170
NAME: TIER 4i SD14_VALVE_BLOCK_6 MACHINE: WARRIOR 1800
ILLUSTRATION:
5
4
7
3
8
2
9
1
10
11
12
Page 171
NAME: TIER 4i SD14_VALVE_BLOCK_6 MACHINE: WARRIOR 1800
ILLUSTRATION:
2 02060216 0 DOWTY SEAL 4
3 17090166 0 1/8" TEST POINT VALVE 1
5 12361757 0 FLYWHEEL PUMP (46) TO FEEDER CONV CV (P) 1
6 02280109 0 ADAPTOR 1
7 12361796 0 FEEDER CV (B) TO FEEDER CONV F/C (P) 1
8 12361775 0 FEEDER CONV CV (A) TO TRACK SOLENOID (P) 1
9 12361798 1 FEEDER CV (T) TO RETURN LINE MANIFOLD TEE 1
[Figure End]
Page 172
NAME: TIER 4i CV115 5 BANK MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 06-22-E.7.1 REV: A
3
2
4
5
1
6
10
7
8
9
24
11
12
13
14
15
16
19
17
23
18
22
21
20
Page 173
NAME: TIER 4i CV115 5 BANK MACHINE: WARRIOR 1800
ILLUSTRATION:

2 02060216 0 DOWTY SEAL 1
3 02060256 0 ADAPTOR 1
4 02060218 0 DOWTY SEAL 10
5 02060231 0 ADAPTOR 10
6 12361779 0 FEEDER LOWER RAM BALL VALVE TO AUXILLARY CV 1
7 12361455 0 SLIDE HOPPER TEE TO P.U. 1
8 12361549 0 PU TO LH HOPPER BH 1
9 12361551 0 PU TO RH HOPPER BH 1
10 12361550 0 PU TO LH HOPPER BH FOR REAR RAM 1
11 12361769 0 TAIL CONV CV (CARRYOVER) TO AUXILLARY CV (P) 1
12 02060202 0 02060215 2
13 02060215 0 02060215 3
14 12361620 0 SCREEN JACKING RAM TEE TO P.U. B.H. 1
15 12361455 0 SLIDE HOPPER TEE TO P.U. 1
16 12361549 0 PU TO LH HOPPER BH 1
17 12361551 0 PU TO RH HOPPER BH 1
18 12361552 0 PU TO RH HOPPER BH FOR REAR RAM 1
19 12361778 0 AUXILLARY CV (T) TO RETURN LINE MANIFOLD 1
20 12361460 0 P.U. TO 3 BANK C.V. 1
21 12260167 0 ADAPTOR 1
22 02010758 0 C/VALVE HANDLE 45DEG 5
23 65500533 0 10266-4S CONTROL VALVE BRACKET 5
24 12260175 0 SEAL KIT Supersedes 12260176 19/02/03 (Non 1

Interchangeable)
[Figure End]
Page 174
NAME: TIER 4i BALLVALVE MACHINE: WARRIOR 1800
ILLUSTRATION:
3
2
1
4
5
Page 175
NAME: TIER 4i BALLVALVE MACHINE: WARRIOR 1800
ILLUSTRATION:
1 12361779 0 FEEDER LOWER RAM BALL VALVE TO AUXILLARY CV 1
2 05010125 0 BALL VALVE 1
3 02060218 0 DOWTY SEAL 2
4 12361457 0 P.U. TO SCREEN ANGLE RAM TEE 1
5 02060297 0 ADAPTOR 2
[Figure End]
Page 176
NAME: TIER 4i FLOW CONTROL VALVE 1 MACHINE: WARRIOR 1800
ILLUSTRATION:
3
1
7
9
Page 177
ILLUSTRATION:
1 12361796 0 FEEDER CV (B) TO FEEDER CONV F/C (P) 1
3 02060216 0 DOWTY SEAL 5
4 03260316 1 PRESSUR RELIEF VALVE 1
5 05060157 0 ADAPTOR 1
6 12361787 1 FEEDER CONV FLOW CONTROL (B) TO PUNIT 1

BULKHEAD
8 12361773 0 FEEDER CONV FLOW CONTROL (T) TO RETURN LINE 1

MANIFOLD
9 12361766 0 FEEDER PRESSURE RELIEF (T) TO RETURN LINE 1

MANIFOLD
[Figure End]
Page 178
ILLUSTRATION:
3
7
5
6
Page 179
ILLUSTRATION:
1 12361772 0 FINES CONV CV (B) TO FINES CONV FLOW CONTROL 1

(P)
2 02280109 0 ADAPTOR 1
3 12361786 0 INES CONV FLOW CONTROL (B) TO PUNIT BULKHEAD 5
5 12361788 1 FINES CONV FLOW CONTROL (T) TO RETURN 1

MANIFOLD
7 02060216 0 DOWTY SEAL 3
[Figure End]
Page 180
ILLUSTRATION:
3
6
Page 181
ILLUSTRATION:
1 12361785 0 FINES CONV FLOW CONTROL (B) TO PUNIT 1

BULKHEAD
3 02060216 0 DOWTY SEAL 3
5 12361774 0 MIDS CONV FLOW CONTROL (T) TO RETURN LINE 1

MANIFOLD
6 12361770 0 MIDS CONV (B) TO MIDS CONV FLOW CONTROL (P) 1
[Figure End]
Page 182
NAME: TIER 4i POWER UNIT FRAME MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 06-22-F REV: A
8
6
3
9
A
10
2
B
11
1
12
13
14
22
23
15
A
16
21
17
18
C
C
20
19
Page 183
NAME: TIER 4i POWER UNIT FRAME MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 06-22-F REV: A
1 12990653 1 TIER4 POWERUNIT PROTECTIVE RUBBER 1
2 06790420 0 SIREN 1
4 03210128 0 ENGINE MOUNTINGS 4
5 12990621 2 TIER4 POWERUNIT BACK PLATE 1
6 12990627 1 TIER4 PUNIT RETURN MANIFOLD 1
8 02060216 0 DOWTY SEAL 8
9 02060206 0 ADAPTOR 1
10 02060217 0 DOWTY SEAL 1
11 06760106 0 ADAPTOR 1
12 12361789 0 REAR RETURN LINE MANIFOLD TO RETURN LINE 1

MANIFOLD
13 12990721 0 TIER4 PUNIT BULKHEAD COVER 1
14 12990629 1 TIER4 SIDE PUMP SUCTION MANIFOLD 1
15 12990600 3 TIER4 POWERUNIT BASEFRAME 1
16 17610106 0 CE MARKED SERIAL PLATE 1
17 12990626 1 BALL VALVE COVER 1
18 12990677 1 BATTERY ACCESS COVER FRONT 1
19 60501042 1 REMOTE CONTROL TRACKING SYSTEM FOR 1

SCREENER
20 17790123 0 REMOTE TRACK PLUG (DOG LEAD) 1
21 17790121 0 REMOTE TRACK SOCKET (DOG LEAD) 1
22 12990678 0 BATTERY ACCESS COVER SIDE 1
23 12990635 0 TIER4 PUNIT BECOOL OIL COOLER MTG 1
[Figure End]
Page 184
NAME: TIER 4i HYDRAULIC TANK MAIN MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 06-22-G REV: A
B
4
30
3
2
5
A
9
8
B
7
10
6
A
A
1
11
12
31
13
14
18
C
23
17
16
15
24
D
29
19
27
28
21
20
22
D
26
C
25
Page 185
ILLUSTRATION:

SEE FIG 04-15-G.1 FOR BREAK DOWN
2 00012035 0 M12X035 SETSCW8.8ZP 1
3 00012006 0 WASHER 1
4 12990723 0 2" SUCTION FILTER FABRICATED SPANNER 1
5 00012002 0 LOCKNUT 1
6 12990632_001 1 HYDRAULIC TANK INSPECTION PLT COVER 1
7 10.22.5010 0 10.22.5010 1
8 02060240 0 ADAPTOR 8
9 02010518 0 LEVEL GAUGE 1
10 12990628 3 TIER4 HYDRAULIC TANK MWA 1
11 12490317 0 ADAPTOR 2
12 06760108 0 DOWTY SEAL 2
13 01190116 0 BALL VALVE 2
14 02110539 2 ADAPTOR 1
15 03260146 0 ADAPTOR 2
16 03260144 0 DOWTY SEAL 2
17 01190115 0 BALL VALVE 2
18 01800162 0 ADAPTOR 2
19 03260153 0 ADAPTOR 1
20 03260392 1 PLASTIC BODY 8
21 03260393 0 CLAMP TOP PLATE 4
22 01920284 0 BOLT M08 4
23 10.21.3411 0 RETURN LINE FILTER 1
24 10.21.3413 0 FILTER ELEMENT FOR 10.21.3411 1
25 02060149 0 ADAPTOR 1
26 02060206 0 ADAPTOR 1
27 10.16.0050 0 1" LOW PRESSURE BALL VALVE 1
28 02060217 0 DOWTY SEAL 2
29 03260153 0 ADAPTOR 1
Page 186
ILLUSTRATION:
31 12990633_001 0 TIER4 HYDRAULIC TANK SEAL 1
[Figure End]
Page 187
Page 188
NAME: TIER 4i TRACK SOLENOIDS MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 06-22-G.1 REV: A
5
1
6
3
2
7
15
8
13
10
11
12
14
Page 189
NAME: TIER 4i TRACK SOLENOIDS MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 06-22-G.1 REV: A
1 65500475 0 617470 SOLENOID FOR 01800275 2
3 02060216 0 DOWTY SEAL 7
5 01920376 0 ADAPTOR 1
6 12463126 0 MAIN CONV CV (A) TO TRACK SOLENOID (P) 1
7 12990631 1 TRACK SOLENOID MTG BRK 1
8 12463141 1 TRACK SOLENOID TO PUNIT BULKHEAD 1
12 02280109 0 ADAPTOR 2
13 12463125 0 FEEDER CONV CV (A) TO TRACK SOLENOID (P) 1
14 12463127 0 TRACK SOLENOID (T) TO HYD TANK 1
15 02060206 0 ADAPTOR 1
[Figure End]
Page 190
NAME: TIER 4i POWER UNIT BACK DOOR MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 06-22-H REV: A
3
2
8
7
1
5
A
6
9
A
21
10
20
14
C
11
B
19
13
12
18
15
17
C
16
Page 191
NAME: TIER 4i POWER UNIT BACK DOOR MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 06-22-H REV: A
1 12.86.3029 0 VISE ACTION COMP. LATCH 1
2 00006025 0 BOLT M06 4
3 00006006 0 WASHER 8
4 00006002 0 LOCKNUT 8
6 12990754 0 RADIATOR COVER ASSEMBLY LID 1
7 12990608 0 RADIATOR DISCHARGE FRAME SPACER PLATE 1

97KW TIER 4I ONLY
8 12990664 0 RADIATOR DISCHARGE FRAME SPACER PLATE 1
TIER 3 ONLY
9 12990752 1 TIER4 RADIATOR DISCHARGE FRAME 1
11 00006002 0 LOCKNUT 4
12 00006006 0 WASHER 4
14 12220155 0 STORAGE BOX 2
15 12990749 0 LHS ACCESS DOOR MWA 1
16 00012035 0 M12X035 SETSCW8.8ZP 4
17 00012006 0 WASHER 8
19 00012002 0 LOCKNUT 4
20 12990607 1 TIER4 PUNIT AIR DISCHARGE GUARD 1
21 12990753 1 RADIATOR COVER ASSEMBLY 1
[Figure End]
Page 192
NAME: TIER 4i CAT 4.4 ENGINE FILTER COMPONENTS MACHINE: WARRIOR 1800
ILLUSTRATION:
5
2
1
A
A
4
C
6
7
11
12
13
10
14
9
8
28
B
15
17
27
16
22
18
26
19
23
24
25
C
B
20
21
Page 193
ILLUSTRATION:
1 12990658 1 CAT C4.4 T4 AIR INDUCTION PIPE 1
2 12890220 0 AIR FILTER 1

FOR BREAK DOWN SEE FIG 06-23-E
3 12990623 2 DONALDSON PSD09 AIR FILTER BRACKET 1
4 12990669 1 CAT C4.4 T4 AIR INDUCTION PIPE TEMP SENSOR 1

256-6454
5 60541020 0 AIR INDICATOR SWITCH (CAT 296-2735) 1
6 65502403 0 WATER TRAP 1
7 65502405 0 WATER TRAP ELEMENT 1
8 12463183 1 FUEL LIFT PUMP TO WATERTRAP 1
9 65502439 0 12V T4 FUEL LIFT PUMP 1
10 00008006 0 WASHER 6
11 00008045 0 BOLT M08 3
12 00012030 0 BOLT M12 2
14 00012006 0 WASHER 2
15 65502441 0 FUEL STRAINER 1
16 12990748 1 TIER4 FUEL LINE FILTER MTG BRACKET 1
17 00008002 0 LOCKNUT 3
18 12463193 0 TIER4 SCAVENGE LINE HOSE 1
20 12463191 0 PUNIT SCAVENGE LINE COMMON HOSE 1
23 65502407 0 FUEL FILTER 2
24 65502409 0 FUEL FILTER ELEMENT 2
25 65502453 0 CAT T4 ENGINE RADIATOR CAP 1
26 65502437 0 BREATHER FILTER 1
27 65502454 0 CAT T4 C4.4(82&98KW) FAN BELT 1

CAT 4.4 (82KW & 98KW)
27 65502455 0 CAT T4 C4.4(129.5KW) FAN BELT 1
CAT 4.4 (129.5KW) (OPTION)
28 65502450 0 CAT T4 C4.4 (82&94KW) RADIATOR 1
CAT 4.4 (82KW & 98KW)
Page 194
ILLUSTRATION:
28 65502451 0 CAT T4 C4.4 (129.5KW) RADIATOR 1

CAT 4.4 (129.5KW) (OPTION)
[Figure End]
Page 195
Page 196
NAME: TIER 4i CAT 4.4 ENGINE EXHAUST MACHINE: WARRIOR 1800
ILLUSTRATION:
4
3
A
2
5
1
12
11
6
10
7
9
Page 197
NAME: TIER 4i CAT 4.4 ENGINE EXHAUST MACHINE: WARRIOR 1800
ILLUSTRATION:
2 12590159 1 EXHAUST EJECTOR 1
3 12990648 0 EXHAUST BELLOW 76.2MM X 250MM 1
4 12990672 2 82KW DPF EXHAUST OUTLET PIPE 1
5 12460141 1 PUMP XIA 46/46/32.3/32.3 1

SEE FIG 06-23-D FOR BREAKDOWN
6 12990686 0 CAT C4.4 T4 RADAITOR GUARD UNDERSIDE 1
7 12990644 0 CAT C4.4 T4 EXTENDED DIPSTICK (82KW & 98KW) 1

SEE FIG 06-23-C FOR BREAKDOWN
9 CAT_C4-4_T4I_82KW 0 CAT_C4-4_T4I_82KW (53045) 1
10 05790365 0 FLANGE PLATE 1
11 17090111 0 BOWEX 65T 1!/4" PARALLEL PUMP HUB 1
[Figure End]
Page 198
NAME: TIER 4i CAT 4.4 ENGINE SIDE PUMP BREAKDOWN MACHINE: WARRIOR 1800
ILLUSTRATION:
3
2
4
5
1
6
7
8
21
20
19
12
11
10
22
13
16
18
17
14
15
Page 199
NAME: TIER 4i CAT 4.4 ENGINE SIDE PUMP BREAKDOWN MACHINE: WARRIOR 1800
ILLUSTRATION:
1 12990671 0 TIER4 CAT C4.4 TANDEM SIDE PUMP MTG BRACKET 1
2 12990645 1 TIER 4 CAT C4.4 SIDE PUMP BASE MTG BRACKET 1
3 00008006 0 WASHER 3
5 00008030 0 BOLT M08 3
6 00012002 0 LOCKNUT 4
7 00012006 0 WASHER 8
8 12490386 0 CAT C4.4 SIDE PUMP MIDDLE MTG BRACKET 1
9 00012040 0 BOLT M12 4
10 02060216 0 DOWTY SEAL 2
12 12361759 1 SIDE PUMP (23) TO TAIL CONV CV (P) 1
13 12361758 1 SIDE PUMP (23) TO MIDS SIDE CONV CV (P) 1
14 SEAL KIT PART NUMBER 0 1

WILL FOLLOW
16 17660109 0 90° FLANGE 1
18 02060227 0 SCREW 4
19 03260144 0 DOWTY SEAL 1
20 03260146 0 ADAPTOR 1
21 12361753 0 SIDE PUMP MANIFOLD TO SIDE PUMP SUCTION 1
22 05190136 0 O-RING 1
[Figure End]
Page 200
NAME: TIER 4i CAT 4.4 ENGINE QUAD PUMP MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 06-23-D REV: A
10
5
4
9
6
A
7
23
11
12
2
1
13
14
A
18
C
22
15
19
17
8
11
20
C
16
21
Page 201
NAME: TIER 4i CAT 4.4 ENGINE QUAD PUMP MACHINE: WARRIOR 1800
ILLUSTRATION:
FIGURE: 06-23-D REV: A
1 12590533 0 QUAD PUMP CENTRE MTG BRK 1
2 12361757 0 FLYWHEEL PUMP (46) TO FEEDER CONV CV (P) 1
3 12361756 0 FLYWHEEL PUMP (46) TO SCREEN CONV CV (P) 1
4 12361755 0 FLYWHEEL PUMP (33) TO COLLECTION CONV CV (P) 1
6 12361797 0 FLYWHEEL PUMP (33) TO COLLECTION CV (P) 1
7 02060216 0 DOWTY SEAL 4
8 00012002 0 LOCKNUT 4
9 00012006 0 WASHER 8
10 12590532 0 QUAD PUMP MTG BRK 1
11 00012040 0 BOLT M12 4
12 12460141 1 PUMP XIA 46/46/32.3/32.3 1
13 03260144 0 DOWTY SEAL 3
14 12361795 1 HYD TANK BALL VALVE TO FLYWHEEL PUMP 1

SUCTION

SUCTION

SUCTION
17 03260146 0 ADAPTOR 3
18 05190136 0 O-RING 3
19 03260253 0 PUMP ADAPTOR 3
21 02060227 0 SCREW 12
22 12590534 0 QUAD PUMP ENG MTG BRK 1
23 65500104 0 SEAL KIT FOR DB PUMP 6690296 1
[Figure End]
Page 202
NAME: TIER 4i CAT 4.4 DONALDSON AIR FILTER BREAKDOWN MACHINE: WARRIOR 1800
ILLUSTRATION:
2
3
Page 203
NAME: TIER 4i CAT 4.4 DONALDSON AIR FILTER BREAKDOWN MACHINE: WARRIOR 1800
ILLUSTRATION:
3 12890220 0 AIR FILTER 1
[Figure End]
Page 204
ILLUSTRATION:
FIGURE: 06-24-A
1 2 3 4 5 6 7 8
17
L ED
3 4 3 4 3 4 3 4 3 4
K1 K4
15 5 6 5 6 5 6 5 6 5 6
7 8 7 8 7 8 7 8 7 8
1 1 1 1 1 1 1 1 N2
18 K6
VBBs 1
K7 K8 K9 K10 K11 F1 F2 F3 F4 F5 F6 F7 F8 GND 2
CAN2_H 3
CAN2_L 4
A B C D E F P/N1
1 1
NAME: TIER 4i CAT 4.4 ELECTRICAL CONTROL PANEL INTERNALS
K5 A
VBBs 1 1 C VBBs 1
1 B VBBs
14 K2 1 2 1 2 1 2 1 2 1 2 VBBs 1
2 2
19 2 2 D GND
2 E GND 2 F GND
VBB1 2
3 3 3 3
3 3
VBB2 3
4 D GND
A GND B GND 4 C GND 4 4 E GND 4 F GND
4
GND 4
5 5
A GND 5 B GND 5 C GND 5
5
CAN1_H 5
6 6 6 D GND
6 6 E GND 6 F GND
CAN1_L 6
7 7 7 7 7
7
K3 20 A 8 D GND
8 VBBs 8 B VBBs 8 C VBBs 8 E GND 8 F GND
13 12 11 10 9
16
REV:
Page 205
A
MACHINE: WARRIOR 1800
NAME: TIER 4i CAT 4.4 ELECTRICAL CONTROL PANEL INTERNALS MACHINE: WARRIOR 1800
ILLUSTRATION:
1 60511011 0 FUSE AUTOMOTIVE 10A 1
9 60519056 0 RELAY 12VDC 8-PIN 8A 1

K11
10 60519056 0 RELAY 12VDC 8-PIN 8A 1
K10
11 60519056 0 RELAY 12VDC 8-PIN 8A 1
K9
12 60519056 0 RELAY 12VDC 8-PIN 8A 1
K8
13 60519056 0 RELAY 12VDC 8-PIN 8A 1
K7
14 60519012 0 RELAY 12VDC HEAVY DUTY 120A 1
K2
15 60519012 0 RELAY 12VDC HEAVY DUTY 120A 1
K1
16 60519016 0 RELAY 12VDC MICRO 4 PIN 1
K3
17 60519042 0 RELAY 12VDC 40A 1
K4
18 60519042 0 RELAY 12VDC 40A 1
K6
19 60519042 0 RELAY 12VDC 40A 1
K5
20 60505109 0 AUTO FUSE HOLDER 1
[Figure End]
Page 206
NAME: CHASSIS FRAME (TRACK SYS A) MACHINE: WARRIOR 1800
ILLUSTRATION: CHASSIS FRAME
Page 207
1 12320103 0 CHASSIS 1
FROM M/C SN 12302602 (INCL:- SNs12302386, 2395 & 2458)
1 12320100 0 CHASSIS FRAME 1
UP TO M/C SN 12302602
2 12320150 0 DIESEL TANK MTG PLATE 1
3 12990355 1 PLASTIC 72 GAL DIESEL TANK 1

FROM SERIAL NO. PID00123CDGC34706 ECO11945
3 01421157 0 FUEL TANK 1
UP TO SERIAL NO. PID00123CDGC34705 ECO11945
4 06920156 0 FUEL GUAGE 1
5 06590153 0 RUBBER 3
6 06590152 0 STRAP 3
6 06690974 0 NEW TYPE 72 GALLON DIESEL TANK SUPPORT 2
STRAP
7 02210163 0 DIESEL TANK CAP 1
8 12220110 0 BEACON MTG BRACKET 1

10 12260163 0 CV113 VALVE BLOCK 1
11 12280102 0 PIN 2
12 12280101 0 PIN 2
13 12320135 0 DIESEL TANK COVER 1
14 12320130 0 POWERUNIT SUPPORT BEAM 1
15 12230525 0 ADJUSTER 2
16 06690361 0 BEACON 1
18 12020303 0 TRACK FRAME RH 1
19 12020304 0 TRACK FRAME LH 1
20 12020305 0 GEARBOX/MOTOR COMPLETE 2
22 06620334 0 GEARBOX MTG BOLT 40
23 06620335 0 GEARBOX MTG WASHER 40
24 12020307 0 STEEL MOTION VALVE 2
25 12020308 0 VALVE MOUNTING BOLT 12
26 12020309 0 SPROCKET 2
Page 208
26 12020309 0 SPROCKET 2
27 06620339 0 SPROCKET MTG BOLT 40
28 06620340 0 MOUNTING WASHER 40
29 12020310 0 TRACK GROUP COMPLETE 2
30 12020311 0 IDLER WHEEL 2
31 07220569 0 TRACK GREASE VALVE 2
32 06620343 0 ADJUSTER GREASE VALV 2
33 06620344 0 GREASE GUN CONNECTOR 2
34 12020312 0 IDLER SPRING ASSY 2
35 12020313 0 IDLER YOKE 2
36 12020314 0 ROLLER 16
37 12020315 0 ROLLER MOUNTING BOLT 38
38 12020316 0 ROLLER MOUNTING WASHER 38
39 02060218 0 DOWTY SEAL 30
40 02060217 0 DOWTY SEAL 1
41 05790355 0 3/8" BSP X 3/4" JIC M/M ADAPTOR (01112) 2
42 00010006 0 M10 WASHER 6
43 00010002 0 LOCKNUT 6
45 02060215 0 02060215 40
46 02060285 0 02060285 6
47 01800005 0 RESTRICTOR ADAPTOR 14
48 02060216 0 DOWTY SEAL 24
49 06560328 0 CARRY OVER VALVE 1
50 02060202 0 02060215 6
51 02060266 0 ADAPTOR 10
52 05010125 0 BALL VALVE 1
53 02060297 0 ADAPTOR 8
54 00016006 0 WASHER 12
55 00016050 0 M16X050 BOLT8.8ZP 6
56 00016002 0 LOCKNUT 6
57 00008070 0 BOLT M08 6
Page 209
58 00008006 0 WASHER 6
59 00008002 0 LOCKNUT 6
60 00000133 0 BOLT M20 2
61 00020002 0 LOCKNUT 2
62 00012035 0 M12X035 SETSCW8.8ZP 22
63 00012002 0 LOCKNUT 40
64 00012006 0 WASHER 40
65 00012040 0 BOLT M12 28
66 00005006 0 WASHER 4
67 00005002 0 LOCKNUT 4
69 02280109 0 ADAPTOR 8
70 12220105 0 CHASSIS POWERUNIT CUTOUT COVER 1
[Figure End]
Page 210
NAME: FUEL TANK FROM SERIAL: PID00123HDGC75391 MACHINE: WARRIOR 1800
ILLUSTRATION:
6
4
3
2
1
A
8
7
A
Page 211
NAME: FUEL TANK FROM SERIAL: PID00123HDGC75391 MACHINE: WARRIOR 1800
ILLUSTRATION:
1 06590153 2 RUBBER 2

STRAP
3 12990786 0 LEVEL GAUGE - NON VENTED 2
4 12990779 0 3/4" BSP METAL FILLER BREATHER (3 MICRON) 1
5 12990787 0 FILLER CAP - NON VENTED 2
6 12990785 0 72 GALLON DIESEL TANK DOMED T4 1
7 00010002 0 LOCKNUT 4
8 00010006 0 M10 WASHER 4
[Figure End]
Page 212
NAME: CHASSIS FRAME (TRACK SYS B) MACHINE: WARRIOR 1800
ILLUSTRATION:
Page 213
ILLUSTRATION:
1 12320103 0 CHASSIS 1
FROM M/C SN 12302602 (INCL:- SN'S 12302386, 2395 & 2458)
1 12320100 0 CHASSIS FRAME 1
UP TO M/C SN 12302602
3 12990355 1 PLASTIC 72 GAL DIESEL TANK 1

3 01421157 0 FUEL TANK 1
4 06920156 0 FUEL GUAGE 1
5 06590153 0 RUBBER 3
6 06590152 0 STRAP 3
STRAP
7 02210163 0 DIESEL TANK CAP 1
8 12220110 0 BEACON MTG BRACKET 1

10 12260163 0 CV113 VALVE BLOCK 1
11 12280102 0 PIN 2
12 12280101 0 PIN 2
13 12320135 0 DIESEL TANK COVER 1
14 12320130 0 POWERUNIT SUPPORT BEAM 1
15 12230525 0 ADJUSTER 2
16 06690361 0 BEACON 1
18 12320203 0 TRACK FRAME COMPLETE RH 1
19 12320202 0 TRACK FRAME COMPLETE LH 1
20 12320207 0 TRACK DRIVE GEARBOX AND MOTOR 2
21 12420417 0 SPROCKET MOUNTING BOLT 40
22 12420416 0 DRIVE SPROCKET 2
23 12420428 0 MASTER PIN & COLLARS 2
24 12420426 0 TRACK SHOE BOLT 448
25 12420427 0 TRACK SHOE NUT 448
26 12420425 0 TRACK SHOE 112
Page 214
ILLUSTRATION:
26 12420425 0 TRACK SHOE 112
27 12420404 0 TRACK CHAIN COMPLETE 2
28 12420418 0 LOWER ROLLER 16
29 12420419 0 ROLLER MOUNTING BOLT 64
30 06620511 0 ROLLER MOUNTING WASHER 64
31 12420421 0 IDLER YOKE 2
32 12420420 0 IDLER GROUP 2
33 12420422 0 IDLER TENSIONER 2
34 06620519 0 GASKET FOR GREASE FITTING 2
35 06620518 0 TENSIONER GREASE FITTING 2
36 12420410 0 MOTION/BRAKING VALVE BLOCK 2
38 12420409 0 GEARBOX MOUNTING BOLT 32
39 02060218 0 DOWTY SEAL 30
40 02060217 0 DOWTY SEAL 1
41 05790355 0 3/8" BSP X 3/4" JIC M/M ADAPTOR (01112) 2
42 00010006 0 M10 WASHER 6
43 00010002 0 LOCKNUT 6
45 02060215 0 02060215 40
46 02060285 0 02060285 6
47 01800005 0 RESTRICTOR ADAPTOR 14
48 02060216 0 DOWTY SEAL 24
49 06560328 0 CARRY OVER VALVE 1
50 02060202 0 02060215 6
51 02060266 0 ADAPTOR 10
52 05010125 0 BALL VALVE 1
53 02060297 0 ADAPTOR 8
54 00016006 0 WASHER 12
55 00016050 0 M16X050 BOLT8.8ZP 6
56 00016002 0 LOCKNUT 6
57 00008070 0 BOLT M08 6
Page 215
ILLUSTRATION:
58 00008006 0 WASHER 6
59 00008002 0 LOCKNUT 6
60 00000133 0 BOLT M20 2
61 00020002 0 LOCKNUT 2
62 00012035 0 M12X035 SETSCW8.8ZP 22
63 00012002 0 LOCKNUT 40
64 00012006 0 WASHER 40
65 00012040 0 BOLT M12 28
66 00005006 0 WASHER 4
67 00005002 0 LOCKNUT 4
69 02280109 0 ADAPTOR 8
70 12220105 0 CHASSIS POWERUNIT CUTOUT COVER 1
[Figure End]
Page 216
NAME: CHASSIS FRAME (JACK-UP SCREENBOX) MACHINE: WARRIOR 1800
Page 217
NAME: CHASSIS FRAME (JACK-UP SCREENBOX) MACHINE: WARRIOR 1800
1 12350305 7 SUBFRAME 1
2 12280115 0 JACK UP SCREEN PIVOT PIN 2
3 12350306 0 JACK-UP ARM 2
4 12260132 0 WARRIOR JACKUP SCREEN RAM 2
5 15980106 0 PIN 2
6 12150163 0 LORD MOUNT PACKER 2
7 12250350 0 RUBBER BUFFER 2
8 12280116 0 JACK UP S/BOX PIN 2
9 12320113 0 TAIL CONVEYOR PIVOT SUPPORT 2
10 12350308 0 SCREEN SUPPORT ARM OUTER 1
11 12350309 0 SCREENBOX SUPPORT ARM INNER SHORT 2
12 12360122 0 RAM 2
[Figure End]
Page 218
NAME: BOLT-ON TRACK CHASSIS MACHINE: WARRIOR 1800
ILLUSTRATION:
Page 219
NAME: BOLT-ON TRACK CHASSIS MACHINE: WARRIOR 1800
ILLUSTRATION:
1 12320107 0 WARRIOR 1800 BOLT-ON TRACK CHASSIS 1

WARRIOR 1800
1 12320109 0 WARRIOR 1800R BOLT-ON TRACK CHASSIS 1
WARRIOR 1800 RADIAL
2 12320120 0 W1800 BOLT-ON TRACK UNDERCARAGE 1
3 12420211 0 12420211 2
4 12420213 0 12420213 2
[Figure End]
Page 220
NAME: BOLT-ON TRACK CHASSIS 3240 MACHINE: WARRIOR 1800
ILLUSTRATION:
Page 221
NAME: BOLT-ON TRACK CHASSIS 3240 MACHINE: WARRIOR 1800
ILLUSTRATION:
1 12320117 0 W1800 BOLT-ON TRACK CHASSIS 1
1 12320127 0 W1800 REV FINES BOLT-ON TRACK CHASSIS 1
2 12320133 0 WARRIOR T4 POWERUNIT CROSS BEAM 1
3 12320118 0 TRACK MOTOR COVER PLATE 2

ORDER ITEM 3, PART NO 12320114, ECO11549
3 12320114 1 TRACK MOTOR GUARD LH 1
4 12320119 0 DK334P-UA145DB MTG BRACKET 2

USED UNTIL APRIL 2010
4 12320145 0 BELL HOUSING ANCHOR (TWO HOLE) 2
NEW BRACKET FROM APRIL 2010~
4 12320146 0 BELL HOUSING ANCHOR (THREE HOLE) 2
OPTIONAL TRACK BRACKET - CONTACT AFTERSALES FOR INFORMATION
4 12320147 0 BELL HOUSING ANCHOR (Z2385) 2
NEW STANDARD TRACK BRACKET FROM AUGUST 2010~
4 12320148 0 BELL HOUSING ANCHOR (LOW DRIVE) LH 1
OPTIONAL TRACK BRACKET (CONTACT AFTERSALES)
6 12320149 0 BELL HOUSING ANCHOR (LOW DRIVE) RH 1

(NOT SHOWN) OPTIONAL TRACK BRACKET - CONTACT AFTERSALES
7 12320115 1 TRACK MOTOR GUARD RH 1
[Figure End]
Page 222
NAME: RADIAL CONVEYOR LOWER MACHINE: WARRIOR 1800
ILLUSTRATION: RADIAL CONVEYOR
Page 223
1 12220120 0 RADIAL CONVEYOR CHASSIS MOUNT 1
3 17630402 0 RADIAL CONVEYOR MOUNTING FRAME 1
4 17630475 0 RADIAL CONVEYOR PIVOT 1
5 17630436 0 RADIAL LG SPROCKET 1
6 09550175 0 RAM 1
7 17630403 0 25X14X70 KEY 2
8 17630476 0 RADIAL CONVEYOR SHAFT CAP 2
9 00020006 0 WASHER 1
10 00020055 0 BOLT M20 1
11 02050446 0 TAPERLOCK 1
12 17630478 0 RADIAL LAY SHAFT 1
13 12150234 0 1/2 X 3/4 X 1 - 3/4 ROUND END KEY 1
14 17680106 0 RADIAL CONVEYOR RAM PIN (24 X 275LG ) 1
15 02010207 0 COTTER PIN 1
16 17630410 0 RADIAL CONVEYOR LOWER SECTION 1
17 09900405 0 TNP2" 3 BEARING 2
18 17630460 0 RADIAL CONV TAIL DRUM 1
19 02050441 0 TAPERLOCK 2
24 05120115 0 ROLLER 5
27 17630415 0 SIDE CONVEYOR TAILDRUM SCRAPER 1
29 12010131 0 CLAMP 4
30 17630417 0 SIDE CONVEYOR TAILDRUM SCRAPER PLATE 1
31 12330660 0 RADIAL CONVEYOR FEEDBOOT 1
Page 224
32 15830471 0 FEEDBOOT RUBBER 2
34 07220152 0 CLAMP PLATE 2
35 17630471 0 FEEDBOOT RUBBER CAP 2
37 17630472 0 FEEDBOOT BACK SKIRTING RUBBER 1
40 06930243 0 ADJUSTER ROD 2
42 17670158 0 DISC ROLLER GUARD 1
43 17670150 0 FEEDBOOT SIDE GUARD 1
44 17670151 0 FEEDBOOT SIDE GUARD 1
45 17670153 0 TAILDRUM REAR GUARD 1
46 17630418 0 HOSE COVER 2
47 15830406 0 ANGLE RAM MOUNTING 1
48 12330650 0 RADIAL CONVEYOR SUPPORT 1
49 17630425 0 RADIAL CONVEYOR LINKAGE ARM 1
50 15830427 0 CONVEYOR LINKAGE ARM 2
51 15860110 0 FOLD RAM 2
52 12360130 0 WARR 1800 RADIAL CONV ANGLE RAM 1
53 15830453 0 WIRE ROPE SUPPORT 1
54 15830457 0 PH1600 RADIAL TRANSPORT CHAIN LONG 2
55 12330630 0 RADIAL CONVEYOR BELT 1

STANDARD RADIAL M/C ONLY
56 15860120 0 CONTROL VALVE(4 BANK) 1

REMOTE RADIAL M/C ONLY
57 05010125 0 BALL VALVE 1
[Figure End]
Page 225
Page 226
NAME: RADIAL CONVEYOR HEAD MACHINE: WARRIOR 1800
Page 227
1 12330625 3 RADIAL CONV HEAD SECTION 1
4 05120115 0 ROLLER 3
6 12270276 0 ROLLER GUARD 1
7 17630428 0 SUPPORT ANGLE 1
8 12280108 0 PIN 2
10 12330626 0 RADIAL CONV TELESCOPIC SECTION 1

(Interchangeable)
14 12230417 0 DRIVE DRUM 1
15 02020211 0 TAPERLOCK 2
16 02010139 0 ROUND END KEY 2
19 02010138 0 TAPERLOCK 1
22 03510147 0 TAPERLOCK 1
27 12130459 0 BELT CLEANER 1
28 06930139 0 TENSIONER 2
Page 228
32 12330627 0 RADIAL CONVEYOR BRETBY GUARD 1
33 12360124 0 RAM 1
[Figure End]
Page 229
Page 230
NAME: TWO WAY SPLIT KIT MACHINE: WARRIOR 1800
ILLUSTRATION: TWO WAY SPLIT KIT
Page 231
NAME: TWO WAY SPLIT KIT MACHINE: WARRIOR 1800
ILLUSTRATION: TWO WAY SPLIT KIT
1 12320110 0 DROP DOWN TAIL CONV MOUNT RH 1
2 12320111 0 DROP DOWN TAIL CONV MOUNT LH 1
3 12330564 0 TAIL CONV BACK EXTENSION 1
4 12350337 0 DROP DOWN TAIL CHUTE 1
5 12350335 0 TOP DECK CHUTE MTG BRACKET RH 1
6 12350336 0 TOP DECK CHUTE MTG BRACKET LH 1
7 00000163 0 BOLT M20 10

NOT SHOWN
8 00000150 0 M24X80 SETSCW8.8ZP 4
NOT SHOWN
9 00024006 0 WASHER 8
NOT SHOWN
10 00020006 0 WASHER 20
NOT SHOWN
11 00020002 0 LOCKNUT 10
NOT SHOWN
12 00024002 0 LOCKNUT 4
NOT SHOWN
13 02060256 0 ADAPTOR 8
NOT SHOWN
14 05060277 0 BSP1" MALE STOPPER PLUG SOLID 10
NOT SHOWN
[Figure End]
Page 232
NAME: STICKER LANGUAGE KITS MACHINE: WARRIOR 1800
ILLUSTRATION: STICKER LANGUAGE KITS
Page 233
NAME: STICKER LANGUAGE KITS MACHINE: WARRIOR 1800
ILLUSTRATION: STICKER LANGUAGE KITS
1 123001G 0 1
WARRIOR 1800 VINAL KIT (SAME FOR ALL M/C'S)
2 123001EN 0 1
WARRIOR 1800 LANGUAGE KIT - ENGLISH
3 123001FR 0 1
WARRIOR 1800 LANGUAGE KIT - FRENCH
4 123001DA 0 1
WARRIOR 1800 LANGUAGE KIT - DANISH
5 123001DE 0 1
WARRIOR 1800 LANGUAGE KIT - GERMAN
6 123001NO 0 1
WARRIOR 1800 LANGUAGE KIT - NORWEGIAN
7 123001PO 0 1
WARRIOR 1800 LANGUAGE KIT - POLAND
8 123001SV 0 1
WARRIOR 1800 LANGUAGE KIT - SWEDISH
9 123001ES 0 1
WARRIOR 1800 LANGUAGE KIT - SPAIN
10 123001NL 0 1
WARRIOR 1800 LANGUAGE KIT - DUTCH
11 123001IT 0 1
WARRIOR 1800 LANGUAGE KIT - ITALIAN
12 123001FI 0 1
WARRIOR 1800 LANGUAGE KIT - FINNISH
[Figure End]
Page 234
NAME: SERVICE SPARES / CONSUMABLES MACHINE: WARRIOR 1800
ILLUSTRATION: SERVICE INFORMATION
Page 235
NAME: SERVICE SPARES / CONSUMABLES MACHINE: WARRIOR 1800
ILLUSTRATION: SERVICE INFORMATION

HYDRAULIC TANK
HYDRAULIC TANK
3 03260232 0 FILTER ELEMENT 1
HYDRAULIC TANK
PERKINS/CAT ENGINE PUMPS
STAGE/TEIR II CAT ENGINE
STAGE/TEIR II CAT ENGINE
9 12290411 0 BATTERY CABLES 1
10 12290425 0 EXHAUST CLAMP 1

CAT C 4.4 83kW (TIER III)
12 12890233 0 FUEL FILTER 1
16 17090255 0 WATER TRAP 1
DEUTZ 2013 (TIER III)
17 17090256 0 FUEL FILTER 2
18 06590206 0 OIL FILTER 1
[Figure End]
Page 236
NAME: RECOMMENDED SPARES 2000 HOURS MACHINE: WARRIOR 1800
ILLUSTRATION:
Page 237
ILLUSTRATION:

ECO11866
2 12230276 0 RUBBER (OUTLET) 2

INCLINED HOPPER AND BELTFEEDER
INCLINED HOPPER AND BELTFEEDER
4 09230195 0 GUIDE ROLLER 2
BELT FEEDER CONVEYOR/SIDE CONVEYOR
BELT FEEDER CONVEYOR
BELT FEEDER CONVEYOR
(Interchangeable)
APRON FEEDER CONVEYOR

DIRECT REPLACEMENT FOR ITEM 9, PART NO.12230121 ECO11814 AND
ECO11864

APRON FEEDER CONVEYOR
HOPPER HORIZONTAL FEEDER
12 12230186 0 RUBBER (OUTLET) 2
HOPPER HORIZONTAL FEEDER
13 12350274 0 SCREEN SIDE DEFLECTOR RUBBER 2
SCREENBOX
14 12350228 0 SCREEN FEED IN CHUTE RUBBER 1
SCREENBOX
15 12250229 0 RUBBER 1
SCREENBOX
16 12350292 0 SCREENBOX OUTLET RUBBER 1
SCREENBOX
SCREENBOX
18 12350105 0 SPRING 12
SCREENBOX
19 12350294 0 SCREEN INLET RUBBER 1
SCREENBOX
SCREENBOX DRIVE
21 01800132 0 V BELT 3
SCREENBOX DRIVE
SCREENBOX DRIVE
23 07250170 0 COMPRESSION SPRING 1
SCREENBOX DRIVE
TAIL CONVEYOR HEAD SECT(1400mm)
TAIL CONVEYOR (1400mm)
TAIL CONVEYOR HEAD SECT(1400mm)/SIDE CONV/COLLECTION CONV
Page 238
ILLUSTRATION:
TAIL CONVEYOR HEAD SECT(1400mm)/SIDE CONV/COLLECTION CONV
28 01940145 0 1240MM IMPACT BAR 6
TAIL CONVEYOR HEAD SECT(1400mm)/COLLECTION CONV
TAIL CONVEYOR HEAD SECT(1400mm)/COLLECTION CONV
TAIL CONVEYOR TAIL SECT(1400mm)
34 12130508 0 IMPACT BAR 2
35 01940145 0 1240MM IMPACT BAR 8
36 12330549 0 TAIL CONVEYOR V PLOUGH RUBBER 1
37 12330545 0 TAIL CONVEYOR REAR RUBBER 1
38 05120115 0 ROLLER 3
SIDE CONVEYOR
39 06930471 0 SIDE ROLLER 2
SIDE CONVEYOR
40 06930470 0 SIDE ROLLER 2
SIDE CONVEYOR
SIDE CONVEYOR
(Interchangeable)
SIDE CONVEYOR HEAD SECTION/COLLECTION CONVEYOR

46 12130459 0 BELT CLEANER 1
SIDE CONVEYOR HEAD SECTION
47 13030111 0 SIDE ROLLER 1
SIDE CONVEYOR MID SECTION
48 13030110 0 SIDE ROLLER 1
SIDE CONVEYOR LOWER SECTION
54 06530103 0 ROLLER 1
55 05420143 0 ROLLER 1
56 12230412 0 BELT CLEANER 1
57 12130508 0 IMPACT BAR 6
Page 239
ILLUSTRATION:
58 09900405 0 TNP2" 3 BEARING 2
59 02420116 0 ADJUSTER ROD 2

61 12230323 0 BELT CLEANER 1
COLLECTION CONVEYOR TAIL DRUM
64 12230680 0 ROLLER 6
66 12230350 0 BELT CLEANER 1
COLLECTION CONVEYOR DRIVE DRUM
67 06930139 0 TENSIONER 2
COLLECTION CONVEYOR DRIVE DRUM
STAGE II CAT ENGINE
STAGE II CAT ENGINE
71 06690280 0 PUMP TRIPLE 1
74 15560130 0 PUMP TANDEM 1
75 03260232 0 FILTER ELEMENT 1
HYDRAULIC TANK
HYDRAULIC TANK
HYDRAULIC TANK
POWERUNIT CONTROL VALVES

CHASSIS FRAME
83 12260163 0 CV113 VALVE BLOCK 1

CHASSIS FRAME
84 12090373 0 TRIPLE PUMP 1
RADIAL WARRIOR M/C ONLY
Page 240
ILLUSTRATION:
88 12890233 0 FUEL FILTER 1
92 17090255 0 WATER TRAP 1
93 17090256 0 FUEL FILTER 2
94 06590206 0 OIL FILTER 1
97 12030194 0 805W GEARBOX 1
[Figure End]
Page 241
Page 242
NAME: ELECTRICAL SPARES MACHINE: WARRIOR 1800
ILLUSTRATION: ELECTRICAL INFORMATION
Page 243
NAME: ELECTRICAL SPARES MACHINE: WARRIOR 1800
2 06790420 0 SIREN 1
3 12290410 0 CONTROL PANEL 1
4 03210237 0 BATTERY 1
6 12290414 0 WATER LEVEL SWITCH 1
7 06690361 0 BEACON 1
8 12290156 0 OIL LEVEL SWITCH 1
9 12290415 0 DOGLEAD 1
[Figure End]
Page 244
NAME: PERKINS/CATERPILLAR WIRING DIAGRAM MACHINE: WARRIOR 1800
Page 245
NAME: PERKINS/CATERPILLAR WIRING DIAGRAM MACHINE: WARRIOR 1800
[Figure End]
Page 246
NAME: MANUAL TRACK WIRING DIAGRAM MACHINE: WARRIOR 1800
Page 247
NAME: MANUAL TRACK WIRING DIAGRAM MACHINE: WARRIOR 1800
[Figure End]
Page 248
NAME: FUSE & RELAY DESIGNATIONS MACHINE: WARRIOR 1800
Page 249
NAME: FUSE & RELAY DESIGNATIONS MACHINE: WARRIOR 1800
[Figure End]
Page 250
NAME: HYDRAULIC PARTS MACHINE: WARRIOR 1800
ILLUSTRATION: HYDRAULIC INFORMATION
Page 251
1 12260120 0 RAM 3
HOPPER INCLINED FEEDER
HOPPER INCLINED FEEDER - ORDER ITEM 2, PART NO. T119137 ECO11814
AND ECO11866

HOPPER INCLINED FEEDER - DIRECT REPLACEMENT FOR ITEM 2, PART NO.
06663105 ECO11814 AND ECO11866
2 T123741 0 ZHENJIANG BMSY SERIES SEAL KIT SPEC DOC 1

3 12030194 0 805W GEARBOX 2
BELT FEEDER
APRON FEEDER
5 12260126 0 RAM 3
HORIZONTAL FEEDER HOPPER
6 12260127 0 RAM 2
7 12360128 0 RAM 2
8 12360129 0 RAM 2
SCREENBOX
SCREENBOX
TAIL CONVEYOR
12 12260123 0 RAM 2
TAIL CONVEYOR
13 12260124 0 RAM 2
TAIL CONVEYOR
14 12360126 0 RAM 2
FINES / SIDE CONVEYOR
FINES / SIDE CONVEYOR MOTOR
FINES CONVEYOR MOTOR
FINES / SIDE CONVEYOR
19 12360125 0 RAM 2
TELESCOPIC FINES / SIDE CONVEYOR
20 12360124 0 RAM 2
SEAL KIT FOR ITEM 22 PART NO. T123737 ECO11814 AND ECO11828
ECO11828

COLLECTION CONVEYOR
COLLECTION CONVEYOR
25 03260195 0 CHECK VALVE 1
Page 252
26 06760109 0 OIL COOLER 1
28 15560140 0 CONTROL VALVE(5 BANK Superseded by 12260165 1


28 12260176 0 SEAL KIT Superseded by 12260175 19/02/03 (Non 1

Interchangeable)

Interchangeable)
29 05010125 0 BALL VALVE 1
31 05760110 0 CONTROL VALVE(4 BANK Superseded by 12260164 1

31 05760119 0 SEAL KIT Superseded by 12260174 23/02/04 (Non 1

Interchangeable)

Interchangeable)

34 15560130 0 PUMP TANDEM 1
35 07290361 0 HUB 1
37 06690280 0 PUMP TRIPLE 1
[Figure End]
Page 253
Page 254
NAME: HYD CIRCUIT STD MACHINE: WARRIOR 1800
Page 255
NAME: HYD CIRCUIT STD MACHINE: WARRIOR 1800
[Figure End]
Page 256
NAME: HYD CIRCUIT (TELE CONV) TEST POINTS MACHINE: WARRIOR 1800
Page 257
NAME: HYD CIRCUIT (TELE CONV) TEST POINTS MACHINE: WARRIOR 1800
[Figure End]
Page 258
NAME: HYD CIRCUIT (RADIAL CONVEYOR) MACHINE: WARRIOR 1800
ILLUSTRATION: HYD CIRCUIT
Page 259
NAME: HYD CIRCUIT (RADIAL CONVEYOR) MACHINE: WARRIOR 1800
ILLUSTRATION: HYD CIRCUIT
[Figure End]
Page 260
NAME: HOSE KITS LISTINGS MACHINE: WARRIOR 1800
Page 261
NAME: HOSE KITS LISTINGS MACHINE: WARRIOR 1800
1 12360430 7 1
INCLINED CHASSIS HOSE KIT 123E
2 12360560 3 1
HORIZONTAL CHASSIS HOSE KIT 123H
3 12360630 0 1
* CHASSIS HOSE KIT(TELESCOPIC SIDE CONVEYOR) 123J
4 12360360 2 1
SIDE CONVEYOR HOSE KIT 123B
5 12360380 2 1
TELESCOPIC SIDE CONVEYOR HOSE KIT 123I
6 12360480 0 1
COLLECTION CONVEYOR HOSE KIT 123G
7 12360490 0 1
SCREENBOX HOSE KIT 123F
8 12260300 2 1
POWERUNIT HOSE KIT (KIT 122A)
9 12260390 2 1
TAIL CONVEYOR HOSE KIT 122D
10 12260420 2 1
HOPPER RAMS HOSE KIT 122D
11 12260650 0 1
APRON FEEDER GREASE HOSE KIT 122 L
12 12260770 0 1
DIESEL PIPES FOR CAT 3054C DIT 122R
13 12260760 0 1
POWERUNIT STAGE I/II CAT3054C DIT 122 Q
[Figure End]
Page 262
NAME: BELT FEEDER HYD. SCH. MACHINE: WARRIOR 1800
ILLUSTRATION: HYD. CIRCUIT
Page 263
NAME: BELT FEEDER HYD. SCH. MACHINE: WARRIOR 1800
[Figure End]
Page 264
NAME: APRON FEEDER HYD. SCH. MACHINE: WARRIOR 1800
Page 265
NAME: APRON FEEDER HYD. SCH. MACHINE: WARRIOR 1800
[Figure End]
Page 266
NAME: BELT FEEDER C/W TELESCOPIC SIDES HYD. SCH. MACHINE: WARRIOR 1800
Page 267
NAME: BELT FEEDER C/W TELESCOPIC SIDES HYD. SCH. MACHINE: WARRIOR 1800
[Figure End]
Page 268
NAME: HYD CIRCUIT FINES SPLIT MACHINE: WARRIOR 1800
ILLUSTRATION:
Page 269
NAME: HYD CIRCUIT FINES SPLIT MACHINE: WARRIOR 1800
ILLUSTRATION:
[Figure End]
Page 270
NAME: DUAL POWER HYDRAULIC SCHEMATIC MACHINE: WARRIOR 1800
ILLUSTRATION:
Page 271
NAME: DUAL POWER HYDRAULIC SCHEMATIC MACHINE: WARRIOR 1800
ILLUSTRATION:
[Figure End]
www.powerscreen.com
Powerscreen, 200 Coalisland Road, Dungannon, Co.Tyrone, BT71 4DR, Northern Ireland.
Tel: +44 (0) 28 8771 8500, Fax: +44 (0) 28 8774 7231, E-mail: [email protected]
Printed in the UK

Warrior 1800 Illustrated Parts Catalog Revision 13

Uploaded by

Copyright:

Available Formats

Warrior 1800 Illustrated Parts Catalog Revision 13

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Warrior 1800 Illustrated Parts Catalog Revision 13

Uploaded by

Copyright:

Available Formats

PARTS BOOK INTRODUCTION

SPARE PARTS – CONTENTS

2. SPARE PARTS ORDERING PROCEDURE……………………….................……………………....................

3. SPARE PARTS ORDER FORM………………………………...……………….................................................

4. UNDERSTANDING YOUR MACHINE SERIAL NUMBER.……………………………....................................

5. PARTS SUPPORT - GOOD PRACTISE ADVICE……………………………..................................................

6. HOW TO READ YOUR TRACK IDENTIFICATION PLATE……………………………....................................

7. WHERE TO FIND YOUR ENGINE SERIAL PLATE……………………….……..............................................

8. FINDING THE SOFTWARE VERSION OF YOUR PDM AND PLC.…………...............................................

10. TYPES OF SCREEN MEDIA ............................................…...………….………….....................................

12. MESH SPECS.............................……..…………………..............................................................................

13. PAINT CODES..............................................…………………………...........................................................

POWERSCREEN PARTS DEPARTMENT

TEREX® reserves the right to change specification without prior notice.

2. SPARE PARTS ORDERING PROCEDURE

Machine Serial Number -

3. SPARE PARTS ORDERING FORM

4. UNDERSTANDING YOUR MACHINE SERIAL NUMBER (SCREENER)

PID 00129 C DG C 6 5315

Year Code Sequence Number

SERIAL NUMBER PLATE

5. PARTS SUPPORT - GOOD PRACTISE ADVICE

6. WHERE TO FIND YOUR TRACK IDENTIFICATION PLATE

Identification Plate Locations

Strickland Tracks Terex Tracks

Terex / Trackline Tracks

7. WHERE TO FIND YOUR ENGINE SERIAL PLATE

Right Hand Side Left Hand Side

8. FINDING THE SOFTWARE VERSION OF YOUR PDM AND PLC

PDM Sticker PLC Sticker

Screener Right Hand Side

Left Hand Side

10. TYPES OF SCREEN MEDIA

Available in a wide range of sizes – For details please contact us.

Woven Screens Elongated Screens

Slow/Fast Screen Hardox Punch Plate

Finger Screens Bofar Bars

Ball Decks Speed Harps

10. TYPES OF SCREEN MEDIA CONTINUED

Polyurathane Modular Panels Rubber Screen Mats

BB – Speedharp aperture e.g. 3mm is 03

CCC – Wire diameter e.g. 1mm is 100, 0.66mm is 066

DD – Wire type e.g. PW is Plain Wire, SS is Stainless Steel wire

If in doubt contact us for correct part number

12. MESH SPECS

YYYY - Mesh aperture e.g. 100mm is 1000, 50mm is 0500

ZZZ - Wire diameter e.g. 12.5mm is 125, 4mm is 040

If in doubt contact us for correct part number

13. PAINT CODES

Powerscreen Green - RAL 5021 (RGB 26/122/99)

Figure Description Page

01-02 HOPPER HORIZONTAL FEEDER 5

01-03 HORIZONTAL BELT FEEDER CONVEYOR 9

01-04 APRON FEEDER CONVEYOR 13

01-05 HORIZONTAL FEEDER (RADIAL M/C) 17

01-06 INCLINED BELT FEEDER CONVEYOR 19

02-02 SCREENBOX TOP DECKS 27

02-03 SCREENBOX BOTTOM DECKS 31

02-04 SCREENBOX DRIVE 35

02-05 SCREENBOX WALKWAYS 39