1 /// 8 0 0 . 5 5 1 .

0 5 4 1
 NEW FOR T HE T OUGH ES T
2020! ARROW
YOU’LL EVER
SHOOT
BLACK LABEL™ QUANTUM™
PAGE 21

You demand tough, accurate arrows. That’s why we make every Gold Tip with
100% pure carbon. Then we hand pick the toughest and most consistent shafts.
We’ve got the callouses to prove it. And you’ve got our promise that if it makes
LOOK FOR THE GOLD TIP “END TO END STRAIGHTNESS” PROMISE
our cut, it’ll make your shot.
At Gold Tip, the pursuit to make the industry’s most consistently straight
arrows never stops. With the End To End Straightness Process, we’ve
taken it to another level. First, every Gold Tip arrow starts with 100% pure PREMIUM HUNTING ARROWS PRECISION TARGET ARROWS
carbon for a stronger shaft that retains its straightness longer shot after Airstrike.................................................6 Pierce Tour............................................30
Kinetic Series........................................8 Ultralight Series....................................32
shot, hunt after hunt. Then, each shaft is 3-point laser-sorted to assure that Hunter Series........................................12 Nine.3 Max............................................34
the entire shaft – from end to middle to end – matches the straightness Velocity Series......................................14 Series 22 .............................................36
Valkyrie.................................................16 X-Cutter Series ...................................37
grade promised. Industry standard measures straightness at the only one
30X Series ...........................................38
point: the center. Now, when you see the Gold Tip E2E Promise you know SPECIALTY HUNTING ARROWS Triple X Series.......................................39
your arrow goes beyond industry standard. And, rest assured, the pursuit Cutdown................................................18
Black Label...........................................20 CROSSBOW BOLTS
won’t stop there. Ted Nugent Series.................................22 Bolt Selection........................................40
Traditional Series..................................24 Swift Series...........................................41
Twister Flu-Flu.....................................26 Ballistic Series......................................42
Nitro Series...........................................43
COVER PHOTO: OWEN STRONELL YOUTH ARROWS
Lightning, Fiberglass..................................28 TECHNICAL DATA
Arrow Components...............................44
Apparel..................................................46
Technical Data.......................................47

2020

G O L D T I P. C O M /// 2 3 /// 8 0 0 . 5 5 1 . 0 5 4 1
G O L D T I P. C O M /// 4 5 /// 8 0 0 . 5 5 1 . 0 5 4 1
 BEAU FAUSETT

STRIKE FASTER.
STRIKE FARTHER.
STRIKE HARDER.
Gold Tip introduces Airstrike™, featuring an ultra-light .204 inside diameter profile
with an extreme front of center design, high modulus carbon construction, and
exclusive Dyna-Tek Slick Shield TM coating.  Built for speed and long range accuracy,
the Airstrike™ closes long distances faster and penetrates deeper with pinpoint
accuracy. It’s the fastest,  most versatile long-range hunting arrow your target
will never see.

BALLIST IC NOCK Al. SS

SPINE COLOR GPI OD COLL AR COLL AR INSER T INSER T
ARROW SPECS

COMPONENT WEIGHTS

SOLD SEPARATELY

400 GRAY 7.2 .254” 15.5 3.4 24.3 69.3

340 GRAY 7.8 .258“ 14.6 3.9 24.9 71.0
300 GRAY 8.5 .262” 13.6 4.0 25.4 72.4
250 GRAY 9.6 .269” 19.0 5.0 26.4 75.3

STRAIGHTNESS TOLERANCE: +/- .001”

WEIGHT TOLERANCE: +/- .5 GR BALLISTIC COLLAR NOCK COLLAR AL. INSERT SS INSERT
AVAILABLE IN: 2” VANES & SOLD SEPARATELY
2.75” FACTORY 4 FLETCHED

AVAILABLE WITH

COATED WITH

FOR DEEPER PENETRATION AND EASIER ARROW REMOVAL FROM TARGETS.

*SEE PAGE 17 FOR SCIENCE

G O L D T I P. C O M /// 6 7 /// 8 0 0 . 5 5 1 . 0 5 4 1
 SOMETIMES LESS
IS MORE
NOCK COLL AR
(COMES STANDARD WITH PLATINUM
BUT AVAILABLE FOR USE ON BOTH)

•I NCREASES BACK END

DURABILITY

LOW-PROFILE
SHIELD CUT VANES
If you’re looking for an arrow that surgically penetrates with blistering speed and •D OUBLE CURVED REAR IMPARTS
will stand up to real-world abuse, you’ve found it. The Gold Tip Kinetic Pierce is MORE STABILITY
•L OWER RISE OF VANE
a micro diameter arrow that’s built to hunt. Its greatly reduced diameter makes REDUCES WIND DRIFT
it resist wind drift for long range accuracy. Its decreased weight makes it fly •T ESTED TO BE AS ACCURATE
AS 2” HP VANES
fast and flat. And when the Pierce impacts its target, it has the energy to punch
through. Thanks to the patent pending Ballistic Collar Insert System, this surgical MICRO DIAMETER SHAFT
arrow has the strength of a jackhammer to take on any hide, meat, or bone you •D ECREASES DRAG
INCREASES PENETRATION
put in front of it. •R ESISTS WIND DRIFT FOR
LONG-RANGE ACCURACY
•R EDUCED WEIGHT ALLOWS
FOR GREATER SPEED

PATENT PENDING BALLISTIC

COLL AR INSERT SYSTEM
•S IGNIFICANTLY INCREASES DURABILITY AT THE
BROADHEAD/SHAFT CONNECTION
•A DDS WEIGHT TO GIVE THE ARROW A HIGHER
FRONT OF CENTER
SPINE COLOR GPI OD SPINE COLOR GPI OD •H ELPS GUIDE TRAJECTORY
ARROW SPECS
ARROW SPECS

500 BLACK 6.6 .222” 500 BLACK 6.6 .222” •F ITS STANDARD THREAD SIZE AND 5/16”
400 BLACK 7.6 .229” 400 BLACK 7.6 .229” DIAMETER POINTS
340 BLACK 8.3 .234“ 340 BLACK 8.3 .234“ •I NTERNAL WEIGHT SYSTEM (FACT) COMPATIBLE.
300 BLACK 9.1 .240” 300 BLACK 9.1 .240” SPECIFIC SIZING NECESSARY
250 BLACK 9.8 .245” 250 BLACK 9.8 .245”

COMPARISON OF
500 SERIES SPINES
GTO NOCK: 5.3 GR BALLISTIC INSERT SYSTEM GTO NOCK: BALLISTIC INSERT SYSTEM PIERCE PLATINUM 500
NOCK COLLAR: 2.5 GR 44 GR 5.3 GR 44 GR
OD: .222 / ID: .166
STRAIGHTNESS TOLERANCE: +/- .0025” STRAIGHTNESS TOLERANCE: +/- .OO6”
WEIGHT TOLERANCE: +/- .5” GR WEIGHT TOLERANCE: +/- 2” GR
AVAILABLE IN: 2.1” FUSION VANES, 2” RAPTOR OR AVAILABLE IN 2.1” FUSION AND 2” RAPTOR VANES
2.75” FACTORY 4 FLETCHED KINETIC 500
OD: .258 / ID: .204
AVAILABLE WITH

HUNTER 500
OD: .291 / ID: .246

*SEE PAGE 17 FOR SCIENCE

G O L D T I P. C O M /// 8 9 /// 8 0 0 . 5 5 1 . 0 5 4 1
 OWEN STRONELL

HARD
HITTING
For bowhunters looking for a durable, hard-hitting, small diameter shaft that still
provides unmatched straightness retention, the Kinetic family of arrows meets
the challenge. If you’re hunting larger game or striving to increase your accuracy
in wind and inclement weather, the Kinetic shafts are engineered to deliver.

TM
TM

SPINE COLOR GPI OD SPINE COLOR GPI OD

ARROW SPECS
ARROW SPECS

500 BLACK 7.6 .258” 500 BLACK 7.6 .258”

400 BLACK 9.5 .270” 400 BLACK 9.5 .270”
340 BLACK 9.9 .272“ 340 BLACK 9.9 .272“
300 BLACK 10.4 .274” 300 BLACK 10.4 .274”
200 BLACK 11.6 .282” 200 BLACK 11.6 .282”

ACCU-BUSHING: 7.3 GR BALLISTIC COLLAR: ACCU-TOUGH INSERT: ACCU-TOUGH NOCK: ACCU-TOUGH INSERT:
NOCK: 5.3 GR 12.8 GR 24.8 GR 11.6 GR 24.8 GR

STRAIGHTNESS TOLERANCE: +/- .0025” STRAIGHTNESS TOLERANCE: +/- .006”

WEIGHT TOLERANCE: +/- .5 GR WEIGHT TOLERANCE: +/- 2 GR
AVAILABLE IN: 2” VANES & AVAILABLE IN: 2” VANES
2.75” FACTORY 4 FLETCHED

AVAILABLE WITH

*SEE PAGE 17 FOR SCIENCE

G O L D T I P. C O M /// 1 0 1 1 /// 8 0 0 . 5 5 1 . 0 5 4 1
 EASTON FAUSETT

ALL-AROUND
VERSATILITY
The sport of bowhunting can often lead to challenging situations and conditions. Gold Tip’s Hunter family of
arrows provide the versatility to meet the demands of every level and challenge you may encounter. Providing
speed, stability and strength, thanks to Gold Tip’s 100% carbon technology, the Hunters have become the “go-to”
hunting arrows for many thousands of bowhunters.

SPINE COLOR GPI OD SPINE COLOR GPI OD

ARROW SPECS
ARROW SPECS

500 BLACK 7.3 .291” 500 BLACK 7.3 .291”

400 BLACK 8.2 .295” 400 BLACK 8.2 .295”
340 BLACK 8.9 .300“ 340 BLACK 8.9 .300“
300 BLACK 9.3 .302” 300 BLACK 9.3 .302”

GT SERIES NOCK: ACCU-LITE INSERT:

GTO SERIES NOCK BUSHING: ACCU-LITE INSERT: 12.2 GR 12.1 GR
12.5 GR + 5.3 GR 12.1 GR

STRAIGHTNESS TOLERANCE: +/- .001” STRAIGHTNESS TOLERANCE: +/- .006”

WEIGHT TOLERANCE: +/- .5 GR WEIGHT TOLERANCE: +/- 2 GR
AVAILABLE IN 2” VANES & AVAILABLE IN 2” & 4” VANES & 4” FEATHERS
2.75” FACTORY 4 FLETCHED

AVAILABLE WITH

SPINE COLOR GPI OD

ARROW SPECS

500 BLACK 7.3 .291”

*SEE PAGE 17 FOR SCIENCE 400 BLACK 8.2 .295”
340 BLACK 8.9 .300“
300 BLACK 9.3 .302”
250 BLACK 10.6 .309”

GT SERIES NOCK: ACCU-LITE INSERT:

12.2 GR 12.1 GR

STRAIGHTNESS TOLERANCE: +/- .003”

WEIGHT TOLERANCE: +/- 2 GR
AVAILABLE IN 2” VANES

G O L D T I P. C O M /// 1 2 1 3 /// 8 0 0 . 5 5 1 . 0 5 4 1
 NEED FOR
SPEED
Built for speed, the entire family of Velocity arrows ensures
you get the most out of the technologically sophisticated
speed bows offered by today’s leading manufacturers.
Offering incredible durability and straightness retention,
with less added weight, the Velocity line fulfills your need SPINE COLOR GPI OD

ARROW SPECS
600 BLACK 5.9 .283”
for speed. 500 BLACK 6.3 .285”
400 BLACK 7.4 .291“
340 BLACK 8.2 .296”
300 BLACK 8.8 .299”

ACCU-LITE NOCK: ACCU-LITE INSERT:

8.3 GR 12.1 GR

STRAIGHTNESS TOLERANCE: +/- .006”

WEIGHT TOLERANCE: +/- 2 GR
AVAILABLE IN 2” VANES

SPINE COLOR GPI OD SPINE COLOR GPI OD

ARROW SPECS

600 BLACK 5.9 .283”

ARROW SPECS

600 BLACK 5.9 .283”

500 BLACK 6.3 .285” 500 BLACK 6.3 .285”
400 BLACK 7.4 .291“ 400 BLACK 7.4 .291“
340 BLACK 8.2 .296” 340 BLACK 8.2 .296”
300 BLACK 8.8 .299” 300 BLACK 8.8 .299”

GTO NOCK: 5.3 GR ACCU-LITE INSERT: ACCU-LITE NOCK: ACCU-LITE INSERT:

NOCK BUSHING: 12.5 GR 12.1 GR 8.3 GR 12.1 GR

STRAIGHTNESS TOLERANCE: +/- .001” STRAIGHTNESS TOLERANCE: +/- .003”

WEIGHT TOLERANCE: +/- .5 GR WEIGHT TOLERANCE: +/- 2 GR
AVAILABLE IN 2” VANES & AVAILABLE IN 2” VANES
2.75” FACTORY 4 FLETCHED

AVAILABLE WITH

*SEE PAGE 17 FOR SCIENCE G O L D T I P. C O M /// 1 4 1 5 /// 8 0 0 . 5 5 1 . 0 5 4 1

 LEVI MORGAN

VALKYRIE
WITH
FACTORY
4 FLETCH
With the launch of the new Velocity Valkyrie, Gold Tip introduces four fletched
straight from the factory - for the first time ever! The Valkyrie comes Factory
Four Fletched with aggressive graphics, lightweight construction and four low-

VALK ARIE
profile vanes for added surface area without sacrificing clearance or speed. That
means more back-end drag, faster stabilization, and group size reductions of 20-
75% with broadheads! Add to that Gold Tip’s 100% Pure Carbon technology for

SPRE AD
unmatched straightness retention and toughness and you get the Valkyrie. It’s
screaming speed with Factory Four Fletch accuracy.

SPINE COLOR GPI OD SPINE COLOR GPI OD

ARROW SPECS
ARROW SPECS

600 BLACK 5.9 .283” 600 BLACK 5.9 .283”

500 BLACK 6.3 .285” 500 BLACK 6.3 .285”
400 BLACK 7.4 .291“ 400 BLACK 7.4 .291“
340 BLACK 8.2 .296” 340 BLACK 8.2 .296”
300 BLACK 8.8 .299” 300 BLACK 8.8 .299” SURFACE AREA
1.39 SQ INCHES x 3 = 4.17 SQ IN

ACCU-LITE NOCK: ACCU-LITE INSERT: ACCU-LITE NOCK: ACCU-LITE INSERT:

8.3 GR 12.1 GR 8.3 GR 12.1 GR
SCIENCE OF 4 FLETCH
STRAIGHTNESS TOLERANCE: +/- .003” STRAIGHTNESS TOLERANCE: +/- .006” SURFACE AREA
WEIGHT TOLERANCE: +/- .2 GR WEIGHT TOLERANCE: +/- 2 GR •A N ARROW 4 FLETCHED WITH 2.75”LOW PROFILE VANES
AVAILABLE IN 2.75” FACTORY 4 FLETCHED AVAILABLE IN 2.75” FACTORY 4 FLETCHED CREATES OVER 5% MORE BACK-END DRAG 1.99 SQ INCHES x 4 = 7.96 SQ IN
•MORE VANE SURFACE AREA = INCREASED IN DRAG
•I NCREASED DRAG STABILIZES YOUR ARROW QUICKER. •D OUBLE CURVED REAR IMPARTS MORE STABILITY
COMES STANDARD WITH
RESULTING IN OVERALL GROUP SIZE REDUCTIONS OF 20-75% •L OWER RISE OF VANE REDUCES WIND DRIFT
•T ESTED TO BE AS ACCURATE AS 2” HP VANES

4 FLETCH OPTION AVAILABLE FOR:

•P IERCE PLATINUM
•K INETIC KAOS •V ALKYRIE XT
•H UNTER PRO •V ALKYRIE
•V ELOCITY PRO •BLACK LABEL

G O L D T I P. C O M /// 1 6 1 7 /// 8 0 0 . 5 5 1 . 0 5 4 1
READY TO SHOOT
RIGHT OUT OF THE BOX

Cutdown Arrows give stores the benefit of offering Gold Tip quality arrows in
convenient, ready to shoot packs at prices that value-driven customers will love.
They come in a 4-pack, cut to length and ready to shoot with factory installed
inserts and points. So, your bow hunters can grab their length in the quantity they
want and head straight to the woods or the range.

SPINE COLOR GPI OD

ARROW SPECS

500 BLACK 7.3 .291”

400 BLACK 8.2 .295”
340 BLACK 8.9 .300“

GT SERIES NOCK: AL. INSERT

11.5 GR

STRAIGHTNESS TOLERANCE: +/- .OO6”

WEIGHT TOLERANCE: +/- 2” GRAINS
AVAILABLE IN 2.1” FUSION AND 2” RAPTOR VANES

27” - 31”
G O L D T I P. C O M /// 1 8 1 9 /// 8 0 0 . 5 5 1 . 0 5 4 1
 STRAIGHTNESS
THAT GOES BEYOND STANDARD,
STRAIGHTNESS, UNMATCHED TOUGHNESS &
MICRO-DIAMETER
LOOKS THAT GO BEYOND DEADLY. PENETRATION.
Gold Tip’s new Black Label goes beyond straightness standards to go beyond your Gold Tip’s Quantum, the newest addition to the Black Label family, is built for freight train
expectations. Every Black Label is laser-sorted at multiple points along the shaft to penetration, and with the micro-diameter .204 design, it lessens the sideways drift compared
assure straightness along the full length, not just the ends. That means accuracy to to larger-diameter arrows. Add the night renegade graphics, and you have a subtle look
impress even your most demanding bow hunters. Add renegade graphics to match Gold matched with Gold Tip’s legendary performance. The convergence of laser straightness,
Tip’s legendary toughness and you get an arrow with looks and performance that kill. unmatched toughness, and micro-diameter penetration, the Black Label Quantum has
performance that flat out kills.

DEALER DEALER
EXCLUSIVE 2020 EXCLUSIVE

SPINE COLOR GPI OD BALLIST IC Al. SS

SPINE COLOR GPI OD COLL AR INSER T INSER T
ARROW SPECS

ARROW SPECS
400 BLACK/GRAY 8.2 .295”

COMPONENT WEIGHTS
SOLD SEPARATELY
340 BLACK/GRAY 8.9 .300“
300 BLACK/GRAY 9.3 .302” 400 BLACK 7.0 .2525” 15.5 24.3 69.3
340 BLACK 7.7 .2570“ 14.6 24.9 71.0
300 BLACK 8.3 .2605” 13.6 25.4 72.4
250 BLACK 9.3 .2680” 19.0 26.4 75.3

GT SERIES NOCK: AL. INSERT

11.5 GR

STRAIGHTNESS TOLERANCE: +/- .OO25” STRAIGHTNESS TOLERANCE: +/- .OO25”

WEIGHT TOLERANCE: +/- 2” GR WEIGHT TOLERANCE: +/- 2” GR BALLISTIC COLLAR AL. INSERT SS INSERT
AVAILABLE IN 2.71” FUSION VANES, 2.71” FACTORY 4 AVAILABLE IN 2.71” FUSION VANES, 2.71” SOLD SEPARATELY
FLETCHED, AND 2” RAPTOR VANES FACTORY 4 FLETCHED, AND 2” RAPTOR VANES

AVAILABLE WITH AVAILABLE WITH

*SEE PAGE 17 FOR SCIENCE *SEE PAGE 17 FOR SCIENCE

G O L D T I P. C O M /// 2 0 2 1 /// 8 0 0 . 5 5 1 . 0 5 4 1
 TED NUGENT

WILDLY
TOUGH
Ted Nugent doesn’t do anything “half way.” And when he asked Gold Tip to make his Signature
Series arrows, he told us the same. They needed to be stronger, faster, and harder hitting.
After all, if you’re going to “Wack’em and stack’em” you need arrows that can make it happen.
The Ted Nugent Signature Series offers three distinct choices to get the job done, each with
its own unique Nugent style.

TM

SPINE COLOR GPI OD SPINE COLOR GPI OD

ARROW SPECS

ARROW SPECS

500 WHITE ZEBRA 8.4 .297” 500 PINK OR PURPLE ZEBRA 8.4 .297”
400 WHITE ZEBRA 9.3 .301“ 400 PINK OR PURPLE ZEBRA 9.3 .301“
300 WHITE ZEBRA 10.8 .313”

GT SERIES NOCK: ACCU-LITE INSERT:

GT SERIES NOCK: ACCU-LITE INSERT: 12.2 GR 12.1 GR
12.2 GR 12.1 GR

STRAIGHTNESS TOLERANCE: +/- .006”

STRAIGHTNESS TOLERANCE: +/- .006” WEIGHT TOLERANCE: +/- 2 GR
WEIGHT TOLERANCE: +/- 2 GR AVAILABLE IN 2” VANES
AVAILABLE IN 2” VANES

G O L D T I P. C O M /// 2 2 2 3 /// 8 0 0 . 5 5 1 . 0 5 4 1
 MODERN
PERFORMANCE
WITH A CLASSIC LOOK

Gold Tip’s Traditional Classic is built of a heavyweight, small diameter carbon shaft that
comes equipped with stainless steel inserts and reinforced Ballistic Collars. The strength and
durability, coupled with the look of a custom footed-shaft makes it the perfect choice for any
sportsman that demands hard-hitting kinetic energy.

SPINE COLOR GPI OD SPINE COLOR GPI OD

ARROW SPECS

600 WOOD GRAIN 9.1 .269”

ARROW SPECS

600 WOOD GRAIN 9.1 .269”

500 WOOD GRAIN 10.2 .274” 500 WOOD GRAIN 10.2 .274”
400 WOOD GRAIN 11.3 .282“ 400 WOOD GRAIN 11.3 .282“
340 WOOD GRAIN 12 .287” 340 WOOD GRAIN 12 .287”

BALLISTIC COLLAR: ACCU-TOUGH NOCK : STAINLESS STEEL

ACCU-TOUGH NOCK: STAINLESS STEEL
12.8 GR 11.6 GR ACCU-TOUGH INSERT:
11.6 GR ACCU-TOUGH INSERT:
FROM 72-80 GR
FROM 72-80 GR

STRAIGHTNESS TOLERANCE: +/- .003” STRAIGHTNESS TOLERANCE: +/- .006”

WEIGHT TOLERANCE: +/- 2 GR WEIGHT TOLERANCE: +/- 2 GR
AVAILABLE IN 5” BARRED & SHEILD CUT FEATHERS AVAILABLE IN 4” FEATHERS
WITH LEFT HELICAL

G O L D T I P. C O M /// 2 4 2 5 /// 8 0 0 . 5 5 1 . 0 5 4 1
 KEVIN JENSEN

UP FOR THE
CHALLENGE
Gold Tip will never forget the needs of the Traditional shooter and now offers two classic
options for the leatherwall addicts out there. The look of a Traditional shaft, with the
performance and durability of our all-carbon construction, the Gold Tip Traditionals will
help that recurve kick it up a notch and look good doing it.

Gold Tip’s spirally-wrapped Twister ® is a feather-fletched flu-flu arrow designed to

minimize flight distance to ensure arrow recovery when hunting small game or shooting
aerial targets. Constructed with a small diameter, thick walled 100% carbon shaft for
maximum durability, the Twister Flu-Flu is built to “put ‘em down and still be found”.

ARROW SPECS SPINE COLOR GPI OD

500 BLACK 7.6 .258”
400 BLACK 9.5 .270”
300 BLACK 10.4 .274“

ACCU-TOUGH NOCK: ACCU-TOUGH INSERT:

11.6 GR 24.8 GR (PRE-INSTALLED)

STRAIGHTNESS TOLERANCE: +/- .006”

SPINE COLOR GPI OD WEIGHT TOLERANCE: +/- 2 GR
3.5” SPRIAL FLETCHED FEATHER
ARROW SPECS

600 WOOD GRAIN 7.8 .295”

500 WOOD GRAIN 8.6 .300”
400 WOOD GRAIN 9.3 .302“
340 WOOD GRAIN 10.5 .308”

GT SERIES NOCK: ACCU-LITE INSERT:

12.2 GR 12.1 GR SPINE COLOR GPI OD
ARROW SPECS

STRAIGHTNESS TOLERANCE: +/- .003” 600 WOOD GRAIN 7.8 .295”

WEIGHT TOLERANCE: +/- 2 GR 500 WOOD GRAIN 8.6 .300”
AVAILABLE IN 5” BARRED & SHEILD CUT FEATHERS 400 WOOD GRAIN 9.3 .302“
WITH LEFT HELICAL
340 WOOD GRAIN 10.5 .308”

GT SERIES NOCK: ACCU-LITE INSERT:

12.2 GR 12.1 GR

STRAIGHTNESS TOLERANCE: +/- .006”

WEIGHT TOLERANCE: +/- 2 GR
AVAILABLE IN 4” FEATHERS

G O L D T I P. C O M /// 2 6 2 7 /// 8 0 0 . 5 5 1 . 0 5 4 1
 CURT AND EVAN HENDERSON

START ‘EM
OUT RIGHT
Gold Tip Youth Arrows are built for the durability, versatility, accuracy and safety
demanded by parents, Boy Scout leaders, NASP Instructors, etc. Our lineup of
youth arrows gives young archers the chance to shoot to their full potential.

There’s nothing more important than starting a youngster out with the confidence
only quality equipment can provide. It all starts right here. And Gold Tip’s going to
make sure they start out safely and correctly.

FIBERGLASS
SPINE COLOR GPI OD
ARROW SPECS

™™ NA BLACK OR NA NA
PINK

SPINE COLOR GPI OD

FIBERGLASS FIBERGLASS INSTALLED GLUE-ON POINT:
ARROW SPECS

NA BLACK NA NA GLUE-ON NOCK GLUE-ON NOCK NA

29” FULL LENGTH SHAFT

FOR USE IN BOWS NOT EXCEEDING 30 LBS IN DRAW WEIGHT

GT SERIES NOCK: INSTALLED GLUE-IN POINT:

12.2 GR 50 GR

28” FULL LENGTH SHAFT

FOR USE IN BOWS NOT EXCEEDING 35 LBS IN DRAW WEIGHT

G O L D T I P. C O M /// 2 8 2 9 /// 8 0 0 . 5 5 1 . 0 5 4 1
 TIM GILLINGHAM

SUDDENLY
THE WIND ISN’T
THE ELEMENT
IT USED TO BE
The Pierce Tour is specifically engineered for outstanding performance in field archery
conditions where long distances rule and unpredictable winds abound. This micro diameter
arrow made with Gold Tip’s 100% Pure Carbon Technology resists wind drift and provides
unmatched straightness retention. That means accurate shots that work in your favor even
when the conditions are not.

SPINE COLOR GPI OD

ARROW SPECS

700 BLACK 5.5 .213”

600 BLACK 6.2 .219”
500 BLACK 6.6 .222”
400 BLACK 7.6 .229”
340 BLACK 8.3 .234“
300 BLACK 9.1 .240”
250 BLACK 9.8 .245”
STRAIGHTNESS TOLERANCE: +/- .001”
WEIGHT TOLERANCE: +/- .5 GRAINS
COMPONENTS SOLD SEPARATELY

G O L D T I P. C O M /// 3 0 3 1 /// 8 0 0 . 5 5 1 . 0 5 4 1
 FOR THE
JOZSEF CSIKOS

WIN
There is really only one way to describe Gold Tip’s lineup of target shafts — dominant! Gold Tip shooters continually
beat the competition in tournament archery. Our 100% carbon technology creates target shafts that are second
to none in terms of construction, consistency, tolerances and straightness retention.

The Ultralight line of target arrows offers the target archer the perfect arrow option for any level of
ability; from the accurate, yet forgiving, beginner-level Entrada, to the performance-packed Pro. With
a wide range of spines, from 700 to 300, and multitude of available components, the Ultralights can
be customized to your personal needs for optimum accuracy.

SPINE COLOR GPI OD

ARROW SPECS
700 BLACK 5.4 .280”
600 BLACK 5.9 .283”
500 BLACK 6.3 .285”
SPINE COLOR GPI OD 400 BLACK 7.4 .291“
340 BLACK 8.2 .296”
ARROW SPECS

700 BLACK 5.4 .280” 300 BLACK 8.8 .299”

600 BLACK 5.9 .283”
500 BLACK 6.3 .285” STRAIGHTNESS TOLERANCE: +/- .003”
400 BLACK 7.4 .291“ WEIGHT TOLERANCE: +/- .5 GR
340 BLACK 8.2 .296” COMPONENTS SOLD SEPARATELY
300 BLACK 8.8 .299”
STRAIGHTNESS TOLERANCE: +/- .001”
WEIGHT TOLERANCE: +/- .5 GR
COMPONENTS SOLD SEPARATELY

SPINE COLOR GPI OD

ARROW SPECS

700 BLACK 5.4 .280”

600 BLACK 5.9 .283”
500 BLACK 6.3 .285”
400 BLACK 7.4 .291“
340 BLACK 8.2 .296”
300 BLACK 8.8 .299”

GT SERIES NOCK: ACCU-LITE INSERT:

12.2 GR 12.1 GR

STRAIGHTNESS TOLERANCE: +/- .006”

WEIGHT TOLERANCE: +/- 2 GR
AVAILABLE IN 2” VANES

G O L D T I P. C O M /// 3 2 3 3 /// 8 0 0 . 5 5 1 . 0 5 4 1
 CREDIT PHOTO: FRANÇOIS DELATTRE

MAX
DIAMETER
MEETS MAX
DURABILITY
The Nine.3 Max Plus and Nine.3 Max Pro are the perfect answers to the
demand for an arrow that pushes the maximum allowable diameter for Indoor
World Archery/FITA events. And thanks to Gold Tip’s legendary 100% Smart
Carbon ® Technology, they maintain pinpoint accuracy shot after shot in the
arrow wrecking stramit targets so common at these events. It’s diameter and
durability taken to the max!

SPINE COLOR GPI OD

ARROW SPECS

250 BLACK 8.3 .365” (9.3mm)

STRAIGHTNESS TOLERANCE: +/- .001”

WEIGHT TOLERANCE: +/- .5 GR SPINE COLOR GPI OD
ARROW SPECS

COMPONENTS SOLD SEPARATELY 250 BLACK 8.3 .365” (9.3mm)

(SEE PAGES 40-41)

STRAIGHTNESS TOLERANCE: +/- .0025”

WEIGHT TOLERANCE: +/- .5 GR
COMPONENTS SOLD SEPARATELY
(SEE PAGES 40-41)

G O L D T I P. C O M /// 3 4 3 5 /// 8 0 0 . 5 5 1 . 0 5 4 1
HIGHER PERFORMANCE FAT SHAFT FAVORITE,
FOR LIGHTER DRAWS & LIGHTWEIGHT
LOWER LENGTHS CONSTRUCTION
There’s a reason the X-Cutter has become the most popular shaft in 3D archery as a perennial
With the Series 22 Plus and Series 22 Pro, shooters with lighter draw weights or podium powerhouse. With exacting tolerances down to +/- .001 straightness and just 7.8 gpi,
lower draw lengths can still get up to speed and score big. Built with Gold Tip’s Smart shooters get line-cutting performance without added weight. In both Plus and Pro grades, the
Carbon ® Technology and at only 7.3 grains per inch, the Series 22 has become one of X-Cutter is unmatched in delivering durability and straightness retention for speed, accuracy
the most popular lightweight 3D shafts on the circuit. and consistency shot after shot.

SPINE COLOR GPI OD SPINE COLOR GPI OD SPINE COLOR GPI OD SPINE COLOR GPI OD

ARROW SPECS
ARROW SPECS
ARROW SPECS

ARROW SPECS

300 BLACK 7.3 .338” 300 BLACK 7.3 .338” 250 BLACK 7.8 .380” 250 BLACK 7.8 .380”

STRAIGHTNESS TOLERANCE: +/- .001” STRAIGHTNESS TOLERANCE: +/- .0025” STRAIGHTNESS TOLERANCE: +/- .001” STRAIGHTNESS TOLERANCE: +/- .0025”
WEIGHT TOLERANCE: +/- .5 GR WEIGHT TOLERANCE: +/- .5 GR WEIGHT TOLERANCE: +/- .5 GR WEIGHT TOLERANCE: +/- .5 GR
COMPONENTS SOLD SEPARATELY COMPONENTS SOLD SEPARATELY COMPONENTS SOLD SEPARATELY COMPONENTS SOLD SEPARATELY
(SEE PAGES 40-41) (SEE PAGES 40-41) (SEE PAGES 40-41) (SEE PAGES 44-45)

G O L D T I P. C O M /// 3 6 3 7 /// 8 0 0 . 5 5 1 . 0 5 4 1
 SNAG 3D ANYTHING ELSE
SCORING IN VEGAS IS A
RINGS GAMBLE
Favored among 3D and indoor shooters alike, the 3OX Plus and 30X Pro Precise enough to shoot 900s and big and stiff enough to handle the fastest bows, The
feature a .398 diameter for line-cutting performance of a large shaft without Triple X Plus and Triple X Pro are among the only sure bets in Vegas. At .421” it’s our largest
sacrificing speed. Engineered with Gold Tip’s Smart Carbon ® Technology and diameter. With an incredibly durable and tough .100 spine and tolerances as tight as +/-
a stiffer .200 spine, every 30X is big enough and tough enough to handle the .001 (Pro), you get the exceptional level of straightness retention and accuracy you need to
fastest bows and keep you hitting the scoring ring when you need it most. get you to the next level on the podium.

SPINE COLOR GPI OD SPINE COLOR GPI OD SPINE COLOR GPI OD SPINE COLOR GPI OD
ARROW SPECS

ARROW SPECS

150 BLACK 8.5 .399” 150 BLACK 8.5 .399”

ARROW SPECS

ARROW SPECS
100 BLACK 9.3 .421” 100 BLACK 9.3 .421”

STRAIGHTNESS TOLERANCE: +/- .001” STRAIGHTNESS TOLERANCE: +/- .0025” STRAIGHTNESS TOLERANCE: +/- .001” STRAIGHTNESS TOLERANCE: +/- .0025”
WEIGHT TOLERANCE: +/- .5 GR WEIGHT TOLERANCE: +/- .5 GR WEIGHT TOLERANCE: +/- .5 GR WEIGHT TOLERANCE: +/- .5 GR
COMPONENTS SOLD SEPARATELY COMPONENTS SOLD SEPARATELY COMPONENTS SOLD SEPARATELY COMPONENTS SOLD SEPARATELY
(SEE PAGES 40-41) (SEE PAGES 40-41) (SEE PAGES 40-41) (SEE PAGES 40-41)

G O L D T I P. C O M /// 3 8 3 9 /// 8 0 0 . 5 5 1 . 0 5 4 1
 CROSSBOW
BOLTS BLISTERING
Crossbows combine the stealth of traditional Vertical Bows with the familiar attributes of shooting a
firearm. Gold Tip’s Bolt offering covers your “ammunition” needs regardless if you are looking for fast, flat
trajectory, magnum knockdown power, or match grade accuracy.

Our crossbow bolts are engineered to be the very best bolts available and incorporate 100% Pure Carbon
SPEED
construction to ensure a durable, straight and consistent projectile. Crossbow technology is consistently
evolving and improving…which is exactly why we have developed a diverse line of bolts to cater to any The Swift is Gold Tip’s most popular bolt choice and has been a staple among crossbow
crossbow hunter’s needs. archers for many years. Available in 20” or 22” lengths and with multiple nocking
options, the Swift is as versatile as it is consistent. The Swift Pro Series features
Think of your crossbow bolt as custom ammunition for your favorite big game rifle. Do you look for blistering a .001” straightness tolerance and industry leading weight tolerances, providing
fast shooting speeds or heavy, hard hitting power? Perhaps you prefer balanced ballistics with unmatched unmatched overall performance for the most discerning crossbow archers.
accuracy? No problem. Gold Tip has you covered.

BE T TER BEST
CROSSBOW BOLTS

BLISTERING SPEED:
STRAIGHTNESS +/- .001”

BALANCED PERFORMANCE: SPINE COLOR GPI OD SPINE COLOR GPI OD

STRAIGHTNESS +/- .001”

ARROW SPECS

ARROW SPECS
NA BLACK 7.3 .338” NA BLACK 7.3 .338”

KNOCKDOWN ENERGY:
STRAIGHTNESS +/- .001”
GT HALF-MOON NOCK: GT SERIES FLAT NOCK: BRASS INSERT: GT HALF-MOON NOCK: GT SERIES FLAT NOCK: BRASS INSERT:
17 GR 11 GR 110 GR 17 GR 11 GR 110 GR

STRAIGHTNESS TOLERANCE: +/- .001” STRAIGHTNESS TOLERANCE: +/- .005”

BOLT SELECTION PAIRINGS WEIGHT TOLERANCE: +/- .5 GR WEIGHT TOLERANCE: +/- 2 GR
CROSSBOW POUNDAGE
CROSSBOW BOLTS

WEIGHT: 394 GR - 413 GR* WEIGHT: 394 GR - 413 GR*

LENGTH: 20” & 22” LENGTH: 20” & 22”
100 - 150 LBS 150 - 175 LBS 175 LBS + *WHEN USED WITH 100 GR FIELD POINT *WHEN USED WITH 100 GR FIELD POINT
SWIF T BALLISTIC NITRO

20” SHAFT - 3.5” VANE 394 GR 20” SHAFT - 3.5” VANE 414 GR 20” SHAFT - 3.5” VANE 486 GR

20” SHAFT - 4” VANE  398 GR 20” SHAFT - 4” VANE  418 GR 20” SHAFT - 4” VANE  490 GR

22” SHAFT - 3.5” VANE 409 GR 22” SHAFT - 3.5” VANE 431 GR 22” SHAFT - 3.5” VANE 514 GR

22” SHAFT - 4” VANE  413 GR 22” SHAFT - 4” VANE  435 GR 22” SHAFT - 4” VANE  518 GR

* FINISHED BOLT WEIGHTS WITH 100 GR POINT

** R EFER TO YOUR CROSSBOW MANUFACTURER’S MINIMUM BOLT WEIGHT REQUIREMENTS TO INSURE SAFE SHOOTING. SHOOTING A BOLT THAT IS TOO LIGHT FOR YOUR
POUNDAGE CAN CAUSE INACCURACY

G O L D T I P. C O M /// 4 0 4 1 /// 8 0 0 . 5 5 1 . 0 5 4 1
BAL ANCED KNOCK DOWN
PERFOMANCE
The Gold Tip Ballistic bolt is built to a weight that falls in between the Swift and the Nitro
ENERGY
Gold Tip’s Nitro bolt has been designed to keep up with today’s fastest and most powerful
bolt offerings, creating another option for crossbow shooters who are looking for optimal crossbows. The Nitro features the same versatility as the Swift and Ballistic, but in a heavier
performance. Ballistic, as well as the .001” straightness tolerance Ballistic Pro, feature weight and stiffer spine to increase kinetic energy and withstand the rigors of today’s high
Gold Tip’s 100% carbon technology for unmatched durability and straightness retention. performance crossbows. Also available is the Nitro Pro, which brings all the toughness and
durability of the standard Nitro with a .001” straightness tolerance.

SPINE COLOR GPI OD SPINE COLOR GPI OD SPINE COLOR GPI OD SPINE COLOR GPI OD
ARROW SPECS
ARROW SPECS

NA BLACK 8.5 .343” NA BLACK 8.5 .343” NA BLACK 13.9 .347” NA BLACK 13.9 .347”

ARROW SPECS

ARROW SPECS
GT HALF-MOON NOCK: GT SERIES FLAT NOCK: BRASS INSERT: GT HALF-MOON NOCK: GT SERIES FLAT NOCK: BRASS INSERT:
GT HALF-MOON NOCK: GT SERIES FLAT NOCK: BRASS INSERT: GT HALF-MOON NOCK: GT SERIES FLAT NOCK: BRASS INSERT:
17 GR 11 GR 110 GR 17 GR 11 GR 110 GR
25 GR 25 GR 60 GR 25 GR 25 GR 60 GR

STRAIGHTNESS TOLERANCE: +/- .001” STRAIGHTNESS TOLERANCE: +/- .005” STRAIGHTNESS TOLERANCE: +/- .001” STRAIGHTNESS TOLERANCE: +/- .005”
WEIGHT TOLERANCE: +/- .5 GR WEIGHT TOLERANCE: +/- 2 GR WEIGHT TOLERANCE: +/- .5 GR WEIGHT TOLERANCE: +/- 2 GR
WEIGHT: 414 GR - 435 GR* WEIGHT: 414 GR - 435 GR* WEIGHT: 486 GR - 518 GR* WEIGHT: 486 GR - 518 GR*
LENGTH: 20” LENGTH: 20” & 22” LENGTH: 20” LENGTH: 20” & 22”
*WHEN USED WITH 100 GR FIELD POINT *WHEN USED WITH 100 GR FIELD POINT *WHEN USED WITH 100 GR FIELD POINT *WHEN USED WITH 100 GR FIELD POINT

G O L D T I P. C O M /// 4 2 4 3 /// 8 0 0 . 5 5 1 . 0 5 4 1
ARROW COMPONENTS AVAIL ABLE VANE COLORS

2” RAPT-X™ VANE: 7 GR 4” DURAVANE: 8.8 GR

VANES
NOCKS

2.1” FUSION X VANE: 7GR 2.75” FUSION X VANE: 8.5 GR

SYSTEM
F.A.C.T.

MODULES
WEIGHT

WEIGHT
.246 GT SERIES: .246 ACCU-LITE: .204 ACCU-TOUGH: WRENCH
12.2 GR 8.3 GR 11.6 GR STANDARD OR
PIERCE SIZES .166: 10 GR .166: 20 GR .204: 10 GR .204: 20 GR .246: 10 GR .246: 20 GR .246: 50 GR
BLACK LABEL
PIERCE K AOS / KINETIC AIRSTRIKE / QUANTUM TRADITIONAL CL ASSIC

INSERTS
(STAINLESS STEEL)

24.8 GR 24.8 GR
500 SPINE 340-400 SPINE Al. INSERT SS INSERT
ALUMINUM: 72 GR 75 GR 78 GR 80 GR
400 SPINE 24.3 GR 400 SPINE 69.3 GR
19.5 GR 600 SPINE 500 SPINE 400 SPINE 340 SPINE
340 SPINE 24.9 GR 340 SPINE 71.0 GR
MUST USE SPINE SPECIFIC COLLAR 300 SPINE 25.4 GR 300 SPINE 72.4 GR
24.8 GR 24.8 GR 250 SPINE 26.4 GR 250 SPINE 75.3 GR
MINI HD PIN: NOCK 300 SPINE 200 SPINE
3.5 GR
AIRSTRIKE

ALL POINTS AND INSERTS ARE DESIGNED TO ACCEPT GOLD TIP’S F.A.C.T. SYSTEM, ALLOWING YOU TO CUSTOMIZE YOUR ARROWS FRONT OF CENTER BALANCE (FOC).
.166 GTO NOCKS: 5.3 GR HD PIN: 6.1 GR WRENCH PIERCE K AOS / KINETIC TRADITIONAL CL ASSIC

BALLISTIC
COLLARS
OPTIONAL SPINE SPECIFIC COLLARS OPTIONAL SPINE SPECIFIC COLLARS

15.5 GR 14.6 GR 13.6 GR 19.0 GR

400 SPINE 340 SPINE 300 SPINE 250 SPINE
24 GR 24 GR 24 GR 14.5 GR 12.8 GR BLACK LABEL
SWIFT/BALLISTIC HALF-MOON: SWIFT/BALLISTIC FLAT: SWIFT/BALLISTIC SWIFT/BALLISTIC NITRO NITRO 500 SPINE 400 SPINE 340 SPINE 500 SPINE 340-400 SPINE QUANTUM
ALUMINUM MOON: ALUMINUM FLAT: ALUMINUM MOON: ALUMINUM FLAT: 11.1 GR 9.2 GR 15 GR 13.9 GR
17 GR 11 GR 600 SPINE 500 SPINE 400 SPINE 340 SPINE
25 GR 25 GR 25 GR 25 GR

24 GR 24 GR 10.4 GR 15.5 GR 15.5 GR 14.6 GR 13.6 GR 19.0 GR

300 SPINE 250 SPINE 300 SPINE 200 SPINE 400 SPINE 340 SPINE 300 SPINE 250 SPINE
PIERCE (.166) AIRSTRIKE KINETIC (.204) .246
(.204)
EZ PULL THREADED FIELD POINTS
700 SPINE: 600 SPINE: 500 SPINE: 400 SPINE:
3.2 GR 2.5 GR 2.2 GR 2.4 GR .204 (9/32”) .246 (5/16”) SERIES 22 (11/32)

250 SPINE : 5.0 GR

600-700 SPINE 340-500 SPINE 250-300 SPINE 300 SPINE : 4.0 GR 340-500 SPINE 200-300 SPINE
BUSHINGS

340 SPINE: 300 SPINE: 250 SPINE: XS PIN: S PIN: L PIN: 340 SPINE : 3.9 GR S GTO: S PIN: L GTO: L PIN: GTO: PIN:

POINTS
2.6 GR 2.6 GR 2.7 GR 9.2 GR 9.5 GR 9.5 GR 400 SPINE : 3.4 GR 7.3 GR 11.5 GR 7.3 GR 11.5 GR 12.5 GR 11.6 GR 85 GR 100 GR 125 GR 85 GR 100 GR 125 GR 100 GR 125 GR

SERIES 22 NINE.3 MA X X CUTTER 30X ACCU-POINTS

(HARDENED STEEL GLUE-IN)

.166 PIERCE .204 KINETIC / .246 SERIES 22 NINE.3 MAX X-CUTTER 30X TRIPLE X
AIRSTRIKE

NOCK: PIN: GTO 166”: .246 NOCK: PIN: GTO 166”: .246 NOCK: PIN: GTO 166”: .246 NOCK: PIN: GTO 166”:
8.5 GR 14 GR 13 GR 13 GR 15.5 GR 17 GR 15.6 GR 17.4 GR 19 GR 18.7 GR 18 GR 21 GR
80, 100 GR 100 GR 120 GR 100 GR 100 GR 120 GR 100 GR 130 GR 80 GR 120 GR 100 GR 130 GR 100 GR 120 GR 120 GR
XS 600-700 S 340-500 L 250-300 S 500 L 200-400 L 200-400
.246 .246 ACCU-LITE TRIPLE X SPINE SPINE SPINE SPINE SPINE SPINE
TIP GRIP TIP GRIP BULLET-NOSE (GLUE IN )
10 GRAM 20 GRAM
LIGHTNING .204 .246 SERIES 22 X-CUTTER 30X TRIPLE X
INSERTS

BRASS: ALUMINUM: REGULAR: SMALL: GREAT FOR INSERTS .246 NOCK: PIN: GTO 166”: 50 GR 85,100 GR 35,80,100 GR 50,80,125 GR 50,90,140 GR 50, 100,150 GR 50,100,150 GR
100 GR 50 GR 12.1 GR 12.1 GR AND VANES 24.6 GR 19.6 GR 23.5 GR
250-400 SPINE 500-700 SPINE

SERIES 22 X CUTTER 30X SWIFT & BALLISTIC NITRO

EXTRAS

ALUMINUM: ALUMINUM: ALUMINUM: BRASS: BRASS:

22.5 GR 36.8 GR 40.2 GR 85, 95, 110 GR 60 GR ARROW TUBE

G O L D T I P. C O M /// 4 4 4 5 /// 8 0 0 . 5 5 1 . 0 5 4 1
 ARROW SELECTION CHARTS

APPAREL TO SEE THE FULL LINE OF GOLD TIP Arrow length is measured from the throat of the nock to the
end of the insert. If you are shooting a longer broadhead than
APPAREL VISIT GOLDTIP.COM field point, you may want to choose a stiffer shaft.
IMPORTANT: PLEASE READ
*Point Weight = The total combined weight of point, insert,
Ballistic Collar and FACT weight.
Step 1: Find your draw and point weight in the chart.
Step 2: Determine the length of your arrow by measuring from
the throat of the nock to the end of the insert.
Step 3: Find the group number in the shaft selection chart.
Step 4: Find your appropriate spine selection for your bow and
use the detail arrow specs chart on the next page to see which
shafts are available in your spine. Arrow length is measured
from the throat of the nock to the end of the insert. If you are
shooting a longer broadhead than field point, you may want to
choose a slightly stiffer shaft.
COMPOUND BOWS - WITH FINGER RELEASE
When shooting finger release, start by selecting an arrow 2
boxes to the weaker side (to the left). Start with the arrow 1”
longer than you selected and cut it down 1/4” at a time until you
have a perfectly tuned shaft using the bare shaft tuning method
outlined in this catalog and at goldtip.com.
TRADITIONAL RECOMMENDATIONS
1. If you are shooting a recurve/longbow, first establish the
draw weight of the bow at the length you draw it to. This is
done by bringing the bow to full draw and having a friend mark
the arrow where it meets the outside of the riser.
2. For either bow, start with the arrow at least 1” longer than
your finished arrow and cut the shaft down 1/4” at a time
until you establish a perfect tune using the shaft tuning guide
outlined in this catalog and at goldtip.com. You can use the Gold
GT HOODIE GT SHOOTER JERSEY Tip weight system to fine tune the spine reaction and increase
the mass weight of the arrow.
ARROW ASSEMBLY
Gold Tip arrows are not only the best performing arrows
on the market, they are also the most user-friendly. With
proper care and adhering to the instructions below you will
find Gold Tip shafts quick and easy to assemble.
ARROW CUTTING
Use only a high speed, abrasive wheel cutoff saw, designed
for cutting arrow shafts. Other methods could result in
damage to the shaft. It is recommended that your arrow
shaft be cut at least one inch in front of the arrow rest at
full draw. If cut too short, they can be drawn past the arrow
rest resulting in the arrow falling from the string, jamming,
or causing damage to the arrow or bow, and could lead to
personal injury.TIP FROM THE PROS: Cut arrow shafts on
both ends to improve straightness. Straightness flaws in
carbon arrows are typically found on the ends.

INSTALLING INSERTS same time, it will allow you to replace the bushing in the event it becomes damaged.
•Read Warning and First Aid instructions on Tip Grip bottle before use. If the pin is damaged after being glued in it is very difficult and sometimes not
•Wear safety glasses. possible to remove the damaged pin without damaging the shaft.
• Do not handle inserts by gluing surfaces. Doing so may lead to improper adhesion. SAFETY INFORMATION
Disposable gloves are recommended. OVERDRAW WARNING: THE USE OF AN OVERDRAW THAT ALLOWS A
• Use TIP GRIP adhesive to install inserts. Do not use hot glue on carbon arrows. SHOOTER TO DRAW THE POINT OF THE ARROW PAST THE SHELF OF THE BOW
GT T-SHIRTS • Clean inside of shaft to a depth of 1 inch with clean water on a cotton swab to SIGNIFICANTLY INCREASES THE RISK OF INJURY TO THE SHOOTER. When using a
remove debris. Allow to dry. bow equipped with an overdraw the arrow should always be cut to a minimum of one
• Apply TIP GRIP adhesive to insert using three generous lines evenly spread length inch in front of the arrow rest at full draw. Selecting the correct arrow length is the
wise along the flats of the insert. responsibility of the shooter and failure to do so could result in severe injury, and/or
• Install insert into shaft and rotate slowly one full turn. damage to shooting equipment.
• With a clean cloth wipe off any excess glue from the shaft and insert. ARROW REST WARNING: Before shooting any Gold Tip arrows it is extremely
• Allow 24 hours for adhesive to cure before shooting. Shooting before adhesive important to inspect the arrow rest to ensure that it is properly adjusted to fit
has fully cured could result in the loss of inserts. TIP FROM THE PROS: A field the diameter of the arrow shaft being used. FAILURE TO PROPERLY ADJUST THE
point can be used as a handle to help with the installation of an insert. For more ARROW REST SIGNIFICANTLY INCREASES THE RISK OF INJURY TO THE SHOOTER
information visit goldtip.com AND DAMAGE TO SHOOTING EQUIPMENT. Incorrect adjustment of the arrow rest
INSTALLING NOCKS may cause the arrow to fall from the arrow rest and/or get jammed in the bow
Gold Tip GT Series, Accu-lite, and Accu-Tough Nocks are designed to fit without which could result in injury to the shooter or bystanders, and damage to shooting
the use of adhesive. Press the nock into the shaft until fully seated and rotate to equipment. ALWAYS MAKE CERTAIN THAT THE ARROW REST IS PROPERLY
get correct vane orientation. Gold Tip Pin Nocks and HD Pin Nocks are designed ADJUSTED BY A QUALIFIED INDIVIDUAL BEFORE SHOOTING.
to fit over a pin nock bushing without adhesive. After following the instructions for ARROW INSPECTION WARNING: INSPECT EACH ARROW FOR DAMAGE PRIOR
installing a Gold Tip pin nock bushing (see below), simply press the nock onto the TO EVERY SHOT. Proper care of carbon arrows can ensure years of quality
GT HATS pin until fully seated and rotate to get correct vane orientation. Gold Tip Pin Nock performance. However, shafts can be damaged. To inspect an arrow, grasp it
Bushings are used with a pin nock or HD pin nock. The bushings can be glued in on both ends and flex it away from yourself and others while visibly and audibly
using TIP GRIP adhesive or pressed in using plastic or Teflon tape. TIP FROM THE checking for splinters, cracks or nicks. Rotate and repeat this inspection process
PROS: Instead of using glue, press your pin nock bushing into the shaft through a four to five times around the entire circumference of the shaft. If you find an arrow
piece of plastic grocery bag, or wrap the bushing with Teflon tape prior to pressing to be damaged in any way discard it immediately. SHOOTING DAMAGED CARBON
it in the shaft. This will allow the bushing to fit tightly without rotating and at the ARROWS CAN RESULT IN ARROW FAILURE AND POSSIBLE INJURY.

G O L D T I P. C O M /// 4 6 4 7 /// 8 0 0 . 5 5 1 . 0 5 4 1
HUNTING T A R G E T
SHAFT/SPINE (+/-.001) (+/-.0025) (+/-.003) (+/-.006) FINISH GPI LENGTH O.D.(IN) O.D.(MM) I.D.(IN) I.D.(MM) SHAFT/SPINE (+/-.001) (+/-.0025) (+/-.003) (+/-.006) FINISH GPI LENGTH O.D.(IN) O.D.(MM) I.D.(IN) O.D.(MM)

HUNTER 500 • • • BLACK 7.3 30” .291 / 7.39 .246 / 6.25 TOUR 700 • BLACK 5.5 30” .213 / 5.41 .166 / 4.22
HUNTER 400 • • • BLACK 8.2 32” .295 / 7.49 .246 / 6.25 TOUR 600 • BLACK 6.2 30” .219 / 5.56 .166 / 4.22
HUNTER 340 • • • BLACK 8.9 32” .300 / 7.62 .246 / 6.25 TOUR 500 • BLACK 6.6 30” .222 / 5.64 .166 / 4.22
HUNTER 300 • • • BLACK 9.3 32” .302 / 7.67 .246 / 6.25 TOUR 400 • BLACK 7.6 32” .229 / 5.82 .166 / 4.22
HUNTER 250 • BLACK 10.6 32” .309 / 7.84 .246 / 6.25 TOUR 340 • BLACK 8.3 32” .234 / 5.94 .166 / 4.22
TOUR 300 • BLACK 9.1 32” .240 / 6.10 .166 / 4.22
VALKYRIE 600 • • • BLACK 5.9 30” .283 / 7.19 .246 / 6.25
TOUR 250 • BLACK 9.8 32” .245 / 6.22 .166 / 4.22
VALKYRIE 500 • • • BLACK 6.3 30” .285 / 7.24 .246 / 6.25
VALKYRIE 400 • • • BLACK 7.4 32” .291 / 7.39 .246 / 6.25 ULTRALIGHT 700 • • • BLACK 5.4 30” .280 / 7.11 .246 / 6.25
VALKYRIE 340 • • • BLACK 8.2 32” .296 / 7.51 .246 / 6.25 ULTRALIGHT 600 • • • BLACK 5.9 30” .283 / 7.19 .246 / 6.25
VALKYRIE 300 • • • BLACK 8.8 32” .299 / 7.60 .246 / 6.25 ULTRALIGHT 500 • • • BLACK 6.3 30” .285 / 7.24 .246 / 6.25
ULTRALIGHT 400 • • • BLACK 7.4 32” .291 / 7.39 .246 / 6.25
VELOCITY 600 • • • BLACK 5.9 30” .283 / 7.19 .246 / 6.25
ULTRALIGHT 340 • • • BLACK 8.2 32” .296 / 7.51 .246 / 6.25
VELOCITY 500 • • • BLACK 6.3 30” .285 / 7.24 .246 / 6.25
ULTRALIGHT 300 • • • BLACK 8.8 32” .299 / 7.60 .246 / 6.25
VELOCITY 400 • • • BLACK 7.4 32” .291 / 7.39 .246 / 6.25
VELOCITY 340 • • • BLACK 8.2 32” .296 / 7.51 .246 / 6.25 NINE.3 MAX • • BLACK 8.3 32” .365 / 9.30 .325 / 8.26
VELOCITY 300 • • • BLACK 8.8 32” .299 / 7.60 .246 / 6.25
SERIES 22 • • BLACK 7.3 32” .338 / 8.59 .300 / 7.62
PIERCE 500 • • BLACK 6.6 30” .222 / 5.63 .166 / 4.22
X-CUTTER • • BLACK 7.8 32” .380 / 9.65 .345 / 8.76
PIERCE 400 • • BLACK 7.6 32” .229 / 5.81 .166 / 4.22
PIERCE 340 • • BLACK 8.3 32” .234 / 5.94 .166 / 4.22 30X • • BLACK 8.5 32” .399 / 10.12 .360 / 9.14
PIERCE 300 • • BLACK 9.1 32” .240 / 6.09 .166 / 4.22 TRIPLE X • • BLACK 9.3 32” .421 / 10.68 .383 / 9.73
PIERCE 250 • • BLACK 9.8 32” .245 / 622 .166 / 4.22
KINETIC 500 • • BLACK 7.6 30” .258 / 6.55 .204 / 5.18
KINETIC 400 • • BLACK 9.5 30” .270 / 6.85 .204 / 5.18
KINETIC 340 • • BLACK 9.9 30” .272 / 6.90 .204 / 5.18
KINETIC 300 • • BLACK 10.4 30” .274 / 6.96 .204 / 5.18 CROSSBOW
KINETIC 200 • • BLACK 11.6 30” .282 / 7.16 .204 / 5.18 SHAFT/SPINE (+/-.001) (+/-.003) (+/-.005) (+/-.006) FINISH GPI LENGTH O.D.(IN) O.D.(MM) I.D.(IN) O.D.(MM)

AIRSTRIKE 400 • SLICK SHIELD™ / GRAY 7.2 32” .254 / 6.45 .204 / 5.18
AIRSTRIKE 340 • SLICK SHIELD™ / GRAY 7.8 32” .258 / 6.55 .204 / 5.18
SWIFT • • BLACK 7.3 20” OR 22” .338 / 8.59 .300 / 7.62
AIRSTRIKE 300 • SLICK SHIELD™ / GRAY 8.5 32” .262 / 6.65 .204 / 5.18
AIRSTRIKE 250 • SLICK SHIELD™ / GRAY 9.6 32” .269 / 6.83 .204 / 5.18
BALLISTIC • • BLACK 8.5 20” OR 22” .343 / 8.71 .300 / 7.62

CUTDOWN 500 BLACK 7.3 26” - 31” .291 / 7.39 .246 / 6.25
NITRO • • BLACK 13.9 20” OR 22” .347 / 8.81 .272 / 6.91
CUTDOWN 400 BLACK 8.2 26” - 31” .295 / 7.49 .246 / 6.25
CUTDOWN 340 BLACK 8.9 26” - 31” .300 / 7.62 .246 / 6.25

BLACK LABEL 400 • BLACK/GRAY 8.2 32” .295 / 7.49 .246 / 6.25
BLACK LABEL 340 • BLACK/GRAY 8.9 32” .300 / 7.62 .246 / 6.25
BLACK LABEL 300 • BLACK/GRAY 9.3 32” .302 / 7.67 .246 / 6.25

TED NUGENT 500 • WHITE - PURPLE - PINK 8.4 30” .297 / 7.54 .246 / 6.25
TED NUGENT 400 • WHITE - PURPLE - PINK 9.3 32” .301 / 7.63 .246 / 6.25
TED NUGENT 300 • WHITE 10.8 32” .313 / 7.95 .246 / 6.25
TRADITIONAL CLASSIC 600 • • WOOD GRAIN 9.1 32” .220 / 6.86 .204 / 5.18
TRADITIONAL CLASSIC 500 • • WOOD GRAIN 10.2 32” .276 / 7.01 ..204 / 5.18
TRADITIONAL CLASSIC 400 • • WOOD GRAIN 11.2 32” .282 / 7.16 .204 / 5.18
TRADITIONAL CLASSIC 340 • • WOOD GRAIN 12 32” .286/ 7.26 .204 / 5.18
TRADITIONAL 600 • • WOOD GRAIN 7.8 30” .295 / 7.49 .246 / 6.25
TRADITIONAL 500 • • WOOD GRAIN 8.6 32” .300 / 7.62 .246 / 6.25
TRADITIONAL 400 • • WOOD GRAIN 9.3 32” .302 / 7.67 .246 / 6.25
TRADITIONAL 340 • • WOOD GRAIN 10.5 32” .308/ 7.82 .246 / 6.25
TWISTER 500 BLACK 7.6 30” .258 / 6.55 .204 / 5.18
TWISTER 400 BLACK 9.5 30” .270 / 6.85 .204 / 5.18
TWISTER 300 BLACK 10.4 30” .274 / 6.96 .204 / 5.18

LIGHTNING YOUTH BLACK N/A 28” N/A .246 / 6.25

FIBERGLASS YOUTH BLACK OR PINK N/A 29” N/A N/A

G O L D T I P. C O M /// 4 8 4 9 /// 8 0 0 . 5 5 1 . 0 5 4 1
BROADHEAD TUNING BOW TUNING
THINGS TO CONSIDER: Although there are a number of acceptable tuning methods that work well, Gold Tip recommends paper tuning for release aid

PIN BUSHING
•The more blade surface a broadhead has, the more steering shooters and bare shaft tuning for finger shooters. Gold Tip also recommends the use of a string loop for compound shooters
ability it will have. For this reason fixed blade broadheads with using a release aid. This will prevent nock pinch and will allow for a more accurate setup and more reliable tuning.
large cutting diameters tend to be slightly more difficult to
tune. PAPER TUNING
•Although mechanical broadheads tend to have fewer tuning Shoot arrows through a suspended sheet of paper at a distance of 4 to 6 feet and observe the resulting tear. See adjustment
issues than fixed blade heads, they still need to be properly INSTALLATION #1 INSTALLATION #2 illustration below to achieve a perfect tune. Make vertical adjustments prior to horizontal adjustments to avoid getting a false
aligned and their point of impact needs to be verified prior to reading due to vane clearance issues.
hunting.
TIP FROM THE PROS: Try spraying your vanes with aerosol foot powder to determine if there is any vane contact with the
•Gold Tip recommends test shooting any style of broadheads arrow rest. Vane contact can cause erratic arrow flight and inaccurate paper tear readings.
for accuracy prior to hunting.
TIP FROM THE PROS: When paper tuning, proper shooting form and a consistent release are critical. Try shooting each arrow
STEP 1: BOW TUNING a number of times to make sure that you are getting a consistent reading. Paper tuning can be time consuming, but will pay
In order to achieve good accuracy with broadheads, it is big dividends in accuracy.
imperative that your bow be properly tuned. Consult our tuning
instructions above and, if needed, consult a technician at your USING WEIGHT SYSTEM APPLYING GLUE INSERT
local pro shop for help with bow tuning.
STEP 2: BROADHEAD ALIGNMENT THIS DIAGRAM DEPICTS A PERFECT TEAR OR BULLET HOLE. THIS MEANS THAT YOUR ARROW
When a broadhead is installed into an arrow shaft, it is common IS PERFECTLY TUNED TO YOUR BOW AND YOU ARE ACHIEVING PERFECT ARROW FLIGHT
for the broadhead to seat incorrectly on the insert. This will

PAPER TUNING
cause misalignment of the broadhead in relation to the arrow
PERFECT TEAR RIGHT TEAR
and will cause the broadhead to wobble when spun. In order to
POSSIBLE CORRECTIONS:

BROADHEAD ALIGNMENT
achieve good accuracy, the broadhead must be centered on the • M OVE REST/CENTER SHOT AWAY FROM
insert in order to spin true on the shaft. To do this, follow the RISER (RIGHT-HANDED BOW)
steps below: • M OVE CABLE GUARD AWAY FROM ARROW
(INCREASE LOAD ON CABLE GUARD)
1) Using an arrow spinner (like the Pine Ridge Arrow Inspector) • ADJUST WHEEL LEAN
place the point of the broadhead against a cardboard box. HIGH TEAR
POSSIBLE CORRECTIONS: LEFT TEAR
As you spin the arrow, the point will make a circle if it is not FIGURE #1 FIGURE #2 POSSIBLE CORRECTIONS:
• MOVE NOCK POINT DOWN
properly aligned. If the broadhead is properly aligned it will • M OVE REST/CENTER SHOT TOWARDS RISER
• MOVE REST UP
not appear to move and no additional steps are needed. • DECREASE LAUNCHER STIFFNESS (RIGHT-HANDED BOW)
(see figure #1) • S HORTEN ARROW LENGTH IF POSSIBLE • M OVE CABLE GUARD TOWARDS ARROW
(DECREASE LOAD ON CABLE GUARD)
2) If the point does make a circle, rotate the point to its LOW TEAR
• ADJUST WHEEL LEAN
uppermost point of movement and mark the point with a • USE STIFFER ARROW
POSSIBLE CORRECTIONS:
• DECREASE DRAW WEIGHT
felt pen at that point. (see figure #2) • RAISE NOCKING POINT
• STIFFEN LAUNCHER STIFFNESS
3) Rotate the arrow 180 degrees from that point and simply
apply pressure to the point of the head on a hard surface. FIGURE #3
The goal of this is to push the broadhead into alignment THIS DIAGRAM DEPICTS OPTIMAL TUNING FOR THE BARE SHAFT TUNING METHOD. BARE
with the insert. (see figure #3) SHAFTS AND FLETCHED ARROWS SHOULD HAVE VERY SIMILAR IMPACT POINTS.
4) Put the arrow back on the spinner and check the head again
for alignment. With a little trial and error you will soon OPTIMAL TUNING WEAK ARROW

BARE SHAFT TUNING

become proficient and will be able to align a broadhead to POSSIBLE CORRECTIONS:
•C UT SHAFTS ¼” AT A TIME
the insert in under a minute. Keep in mind that shooting an • USE A STIFFER SPINED ARROW
arrow can cause misalignment, so it is a good idea to spin • DECREASE POINT WEIGHT
your broadhead tipped arrows repeatedly, particularly STIFF ARROW •D ECREASE POUNDAGE 1/8
after shooting them. POSSIBLE CORRECTIONS: TURN AT A TIME
• USE A LONGER SHAFT • A DD WEIGHT TO REAR OF SHAFT
STEP 3: FLETCHING • USE A LIGHTER SPINED SHAFT WITH WRAPS, FLETCHING, OR GOLD
After bow tuning and broadhead alignment, you are now ready • A DD WEIGHT TO THE INSERT USING TIP’S ULTRALIGHT NOCK ADAPTOR
GOLD TIP’S WEIGHT SYSTEM OR BY • INCREASE PLUNGER TENSIONS
to test your arrows for accuracy. If you are experiencing poor ADDING A HEAVIER WEIGHT POINT
accuracy with a well tuned bow and properly aligned broadheads, The Flex it First logo is our way of reminding you to flex • D ECREASE CUSHION PLUNGER
it is likely that you are not giving the arrow enough guidance. The each shaft to test it for safety periodically – especially TENSION OR REST SIDE TENSION
HIGH NOCK POINT
answer to this is fletching. Increasing the amount of fletching after shooting groups or if you miss a target. Why? Every • A DD POUNDAGE TO THE LIMBS 1/8
POSSIBLE CORRECTIONS:
TURN AT A TIME
either by using longer vanes, or more vanes (4-fletch instead of Gold Tip arrow leaves our factory as the toughest, safest • MOVE NOCK POINT DOWN
3-fletch) will give better guidance and increased accuracy. Be arrow we can make. But like every product, there’s a • MOVE ARROW REST UP
careful however, as too much fletching can have other adverse chance that your arrows could sustain damage in shipping, LOW NOCK POINT
effects such as excessive drag than can also hamper performance. stocking, and shooting that isn’t visible to the eye. Simply POSSIBLE CORRECTIONS:
• MOVE NOCK POINT UP
The key is finding a happy medium. This may take some trial and flex your arrows before shooting to be sure that your • MOVE ARROW REST DOWN
error depending on your setup. The best rule of thumb is to use arrow is not damaged. If there is damage, you will see the
the smallest amount of fletching possible while still being able to carbon seperate or the shaft will break. That way, you’ll
achieve field point accuracy with your broadheads. keep shooting safe and straight. Damn Straight.

G O L D T I P. C O M /// 5 0 5 1 /// 8 0 0 . 5 5 1 . 0 5 4 1
2020
 YOU MAY NOT KNOW WHAT IT MEANS,
CONTENTS BUT YOUR BOW DOES.

It’s about achieving peak performance from your archery

55HUNTING STABILIZERS equipment, whether your sights are set on a 3D target at the
local range or a trophy whitetail in the heart of the Midwest.

65TARGET STABILIZERS
Peak performance that can only be gained through better
balance, increased stability, less torque and reduced vibration.
72MOUNTING HARDWARE
Peak performance that breeds consistency and ultimately
greater shooting confidence.
77BEE STINGER™
GEAR

Bee Stinger™ Stabilizers are engineered to deliver the

78TECHNICAL SPECS advantages your bow needs to achieve its peak performance
to achieve its MAXIMUM MOMENT OF INERTIA.

GIVING YOU THE CONFIDENCE TO CONNECT

You’ve practiced, you’ve prepared - you’re ready. And with a Bee Stinger™ hunting stabilizer,
you know your bow is ready too. Featuring machined aluminum end caps, steel weights, Ultra
Stiff 100% Carbon Rod, and Sims Internal Dampers your Bee Stinger™ is engineered to help
you acquire targets faster, hold steadier, diminish torque, reduce vibration and finish on target.
Now, you know you can make the shot because you know you’ve got a Bee Stinger™.

54 800.551.0541 • BEESTINGER.COM 55
 MICROHEX™ HUNTING AVAILABLE COLORS
You’re not into gimmicks, and neither are we. Introducing what the archery industry has
never seen before. A wind-slicing micro-diameter stabilizer with Bee Stinger exclusive
Countervail® technology. Countervail® proprietary material is built right into the OLIVE
carbon bar – it may seem insignificant, but the data proves otherwise. Quicker damping
and reduced recoil offer a smoother feel and quieter shot – without adding weight or
sacrificing stiffness. Stabilization you’ll appreciate when it’s time to send it.
BROWN

FITS ALL CURRENT BEESTINGER

HARDWARE MOUNTS GREY

TAN

MICRO DIAMETER BLACK

FOR WINDY CONDITIONS
TECHNOLOGY
DAMPENS QUICK FOR
LESS VIBRATION
0.75” 0.5” STAINLESS STEEL STUD
FOR OPTIMAL CONSTRUCTION, GREEN
RIGIDITY AND ADJUSTABILITY

6 INCH
RED

8 INCH

3 INDEPENDENT 1 OZ. 10 INCH MOSSY OAK COUNTRY

POWDER COATED
END WEIGHTS
AVAILABLE SIZES
PATENTED DESIGN

BEE STINGER™ BAR LENGTHS ARE MEASURED FROM CAP TO CAP.

56 WEIGHTS ARE NOT INCLUDED IN QUOTED LENGTH.
800.551.0541 • BEESTINGER.COM 57
 MICROHEX™ COUNTER SLIDE
Achieving perfect balance and offsetting the weight of your sight, quiver and other
accessories has never been more accurate, adaptable, or simple. The new Bee Stinger™
Microhex™ Counter Slide offers limitless configurations for you to customize the optimal
balance for you - whether you’re hunting or target shooting.

STANDARD COLOR:
MATTE BLACK

WITH DOVETAIL MOUNT

SHOWN WITH MICROHEX™

DOVETAIL MOUNT

10 INCH

12 INCH

15 INCH
• 5 INDIVIDUAL 1 OZ. WEIGHTS AND SLIDING
BRACKET ALLOW FOR MINUTE AJUSTMENTS STANDARD
TO ACHIEVE PERFECT BALANCE

• OFFSETS THE WEIGHT OF SIGHT, QUIVER,

AND OTHER ACCESSORIES
10 INCH
• ALLOWS ADDITIONAL WEIGHT
DISTRIBUTION BOTH FORWARD AND BACK
12 INCH

EARTHTONE COLORS: 15 INCH

OLIVE BROWN GREY TAN

AVAILABLE SIZES
Bee Stinger™ bar lengths are measured
from cap to cap. Weights are NOT
included in quoted stabilizer lengths.

58 800.551.0541 • BEESTINGER.COM 59
 SPORT HUNTER XTREME
TAKE YOUR NEXT SHOT TO THE XTREME
This season, take your shooting to the Xtreme! The Sport Hunter Xtreme was engineered
to help provide superior stabilization while conquering shot-induced vibration, resulting
in the ultimate hunting stabilizer. The Sims Internal Damper and De-resonator combine
to effectively minimize vibration transferred from the riser to the stabilizer upon release
of the arrow. The individual 1oz. end-weights allow users to customize their stabilizer to
meet the ideal balance requirements of their particular hunting bow. Together, it equals
added confidence to make your shot of a lifetime.

STANDARD COLOR: CAMO FINISH:

MATTE BLACK MOSSY OAK BREAK-UP COUNTRY
MACHINED ALUMINUM
END CAP

SIMS INTERNAL
DAMPER
ABSORBS VIBRATION FOR BETTER FEEL

SIMS DE-RESONATOR
ENGINEERED FOR SUPERIOR STAINLESS STEEL STUD
VIBRATION DAMPING FOR OPTIMAL CONSTRUCTION,
RIGIDITY AND ADJUSTABILITY

6 INCH

8 INCH

3 INDEPENDENT 1 OZ. 10 INCH

POWDER COATED
END WEIGHTS
PATENTED DESIGN AVAILABLE SIZES
BEE STINGER™BAR LENGTHS ARE MEASURED FROM CAP TO CAP.
WEIGHTS ARE NOT INCLUDED IN QUOTED LENGTH.
60 800.551.0541 • BEESTINGER.COM 61
SPORT HUNTER XTREME SYSTEM YAHSTI PERKINS-KILLER

TOURNAMENT PROVEN, HUNTER APPROVED

For years, world-class target archers have known the benefits of combining front and back
bar stabilizers for superior balance and shot control. Now, Bee Stinger™ brings this same
stabilization strategy to the hunting world with the Sport Hunter Xtreme System. The system
features a longer front SHX stabilizer, a shorter back SHX stabilizer, both mounted to the Elite
Side Arm for maximum adjustability. Together, the SHX System provides maximum balance and
stabilization, assuring maximum moment of inertia. Feel the difference in your hand and with
regular use, shot groupings will tighten at extended distances.

AVAILABLE MODELS: SPORT HUNTER XTREME STABILIZER

• XTREME 8.6 SEE COMPLETE ILLUSTRATION AND BREAK-DOWN
8” FRONT BAR, 6” BACK BAR ON PAGE 4
• XTREME 10.8
10” FRONT BAR, 8” BACK BAR
XTREME 8.6 INCLUDES:
(1) 8” SHX STABILIZER
(1) 6” SHX STABILIZER
(1) ELITE ADJUSTABLE SIDE ARM
ELITE ADJUSTABLE SIDE ARM
WITH BUILT IN QUICK DISCONNECTS
XTREME 10.8 INCLUDES:
(1) 10” SHX STABILIZER
(1) 8” SHX STABILIZER
(1) ELITE ADJUSTABLE SIDE ARM
WITH BUILT IN QUICK DISCONNECTS

AVAILABLE COLORS:

Bee Stinger™ bar lengths are measured

from cap to cap. Weights are NOT
included in quoted stabilizer lengths.

8 INCH

6 INCH

10 INCH

8 INCH

62 800.551.0541 • BEESTINGER.COM 63
 SPORT HUNTER COUNTER SLIDE SCOTTY HASTING

Achieving perfect balance and offsetting the weight of your sight, quiver and other
accessories has never been more accurate, adaptable, or simple. The Bee Stinger™ Counter
Slide offers limitless configurations for you to customize the optimal balance for you -
whether you’re hunting or target shooting.

• 5 INDIVIDUAL 1 OZ. WEIGHTS AND SLIDING

BRACKET ALLOW FOR MINUTE
AJUSTMENTS TO ACHIEVE PERFECT BALANCE

• OFFSETS THE WEIGHT OF SIGHT, QUIVER, AND

OTHER ACCESSORIES

• ALLOWS ADDITIONAL WEIGHT DISTRIBUTION

BOTH FORWARD AND BACK

STANDARD COLOR:
MATTE BLACK WHERE CONSISTENCY LEADS TO SUCCESS

Human error — it can mean the difference between standing at the top of the podium
or the bottom; winning gold or silver — and for the Pros, it’s the difference between
making a living or simply earning enough for gas money home. A light torque of the bow,
10 INCH a little shake in the sight picture — turns a 12 into a 10. That’s why the World’s leading
target archers depend on Bee Stinger™ target stabilizers to help tame human error.
12 INCH
Shot after shot, Bee Stinger™ target stabilizers provide the superior balance and rock-
solid stability needed to acquire targets faster, hold steadier, and deliver repetitive
15 INCH
performance. Technically speaking, Bee Stinger™ target stabilizers work to neutralize the
negative effects of human error and allow the bow to achieve the “maximum moment of
AVAILABLE SIZES inertia” – the closest point of perfection for the bow as the arrow is released.
Bee Stinger™ bar lengths are But what does it all REALLY mean? CONSISTENCY. Because within the realm of
measured from cap to cap. Weights
are NOT included in quoted archery, consistency doesn’t just win the day – it rules the world.
stabilizer lengths.

64 800.551.0541 • BEESTINGER.COM 65
 MICROHEX™ TARGET
You’re never finished, you’re never satisfied – we relate. New for 2018, we introduce what
the archery industry has never seen before. The Microhex™ Target. A wind-slicing micro- V-BAR LENGTHS:
diameter stabilizer with Bee Stinger exclusive Countervail® technology. Countervail®
proprietary material is built right into the carbon bar – it may seem insignificant, but the 10 INCH
data proves otherwise. Quicker damping and reduced recoil offer a smoother feel and
quieter shot – without adding weight or sacrificing stiffness. The new Microhex™ 12 INCH

smooths both you and your bow’s rough spots, as if you had any.
15 INCH
ELITE ADJUSTABLE SIDE ARM SOLD SEPARATELY.

INCLUDED WITH THE 20” WIND BAR: STABILIZER LENGTHS:

• (1) 4 OZ. AND (2) 1 OZ. END WEIGHTS

INCLUDED WITH THE 24”, 27”, 30”, 20 INCH WIND BAR

33”, 36” STABILIZERS:
• (3) INDEPENDENT 1 OZ. END WEIGHTS
24 INCH

27 INCH

30 INCH

33 INCH

36 INCH

0.75” 0.5”

AVAILABLE COLORS:
BLACKOUT

V-BAR THEORY OF USES BLACK/WHITE

V-Bar, side-rod or back-bar…no matter what you call them, they
are an essential tool to achieve optimum stabilization. Using the
BLACK0UT
same carbon technology as our front stabilizers, Bee Stinger™ cuts
no corners when it comes to materials. To off-set counter forces
BLACK/WHITE
and maximize stabilization, put as much or as little end weight as
desired. Create a symmetrical or one side counter balance, our
accessories give you numerous options.

66 BEE STINGER BAR LENGTHS ARE MEASURED FROM CAP TO CAP.

WEIGHTS ARE NOT INCLUDED IN QUOTED STABILIZER LENGTHS. 800.551.0541 • BEESTINGER.COM 67
 PREMIER PLUS
MATCH GRADE PERFORMANCE
The tournament-proven success of the Premier Plus Series is a
testament to quality construction. Built with a proprietary high
V-BAR LENGTHS:
modulus carbon, Premier Plus stabilizers provide extreme rigidity
10 INCH
for maximum stabilization. Each Premier Plus target stabilizer
includes independent weights for customized balance. Experience
12 INCH
greater down-range accuracy and more consistent overall shooting
with the Premier Plus. The choice of World Champions, Premier
15 INCH
Plus target stabilizers deliver “match grade” performance.

STABILIZER LENGTHS:
2020 20 INCH WIND BAR

24 INCH

27 INCH

30 INCH

33 INCH
INCLUDED WITH THE 20” WIND BAR:
• (1) 4 OZ. AND (2) 1 OZ. END WEIGHTS
36 INCH
INCLUDED WITH THE 24”, 27”, 30”, 33”, 36” STABILIZERS:
• (3) INDEPENDENT 1 OZ. END WEIGHTS

ELITE ADJUSTABLE SIDE ARM SOLD SEPARATELY.

AVAILABLE COLORS:
BLACK

V-BAR THEORY OF USES STONE

V-Bar, side-rod or back-bar…no matter what you call them, they

WHITE
are an essential tool to achieve optimum stabilization. Using the
same carbon technology as our front stabilizers, Bee Stinger™ cuts
no corners when it comes to materials. To off-set counter forces BLACK
and maximize stabilization, put as much or as little end weight as
desired. Create a symmetrical or one side counter balance, our STONE
accessories give you numerous options.
WHITE

68 BEE STINGER BAR LENGTHS ARE MEASURED FROM CAP TO CAP.

WEIGHTS ARE NOT INCLUDED IN QUOTED STABILIZER LENGTHS. 800.551.0541 • BEESTINGER.COM 69
 COMPETITOR BAR FREESTYLE COMPETITOR KIT
PRO-GRADE PERFORMANCE, MAXIMUM STABILITY MADE EASY
AFFORDABLY PRICED

Tournament-grade performance at an affordable price; that’s The experts at Bee Stinger™ have constructed the Freestyle Competitor kit
what the Competitor bar offers target archers of all levels. with everything you need for maximum stabilization right from the start.
The Internal Damper smooths out any vibration, while the Centered around the stabilizer and V-bar, the kit features an adjustable side bar
independent weight system allows for customized balance - and quick disconnect for easy mounting. The kit also includes (1) 4 oz. stainless
and the perfect length to weight ratio for your bow. steel end-weight and (3) independent 1 oz. stainless steel end-weights, for
customized balance to achieve optimum performance, with minimal effort.

COMPETITOR BAR
SHOWN WITH AVAILABLE
ELITE ADJUSTABLE SIDE ARM.

2020 ELITE ADJUSTABLE SIDE ARM 2020

SOLD SEPARATELY INCLUDED WITH EACH
STABILIZER BAR:
20”: (1) 4 OZ. AND (2) 1 OZ. END WEIGHTS FREESTYLE COMPETITOR KIT
24”, 27”, 30”, 33”, 36” STABILIZERS: INCLUDES:
(3) INDEPENDENT 1 OZ. END WEIGHTS (1) 30” COMPETITOR STABILIZER
(1) 4 OZ. STAINLESS STEEL END WEIGHT
AVAILABLE COMPETITOR V-BAR LENGTHS: (3) INDEPENDENT 1 OZ. STAINLESS
10”, 12”, 15” STEEL END WEIGHTS
(1) 12” V-BAR (WEIGHTS NOT INCLUDED)
(1) ADJUSTABLE SIDE-BAR
(1) QUICK DISCONNECT

AVAILABLE COMPETITOR BAR LENGTHS:

20”, 24”, 27”, 30”, 33”, 36”

BEE STINGER™ BAR LENGTHS ARE MEASURED FROM CAP TO CAP.

WEIGHTS ARE NOT INCLUDED IN QUOTED STABILIZER LENGTHS.

EACH COMPETITOR KIT COMES

WITH THE CARRYING TUBE.

70 800.551.0541 • BEESTINGER.COM 71
STABILIZER MOUNTS AND HARDWARE STABILIZER EXTENSIONS:
When you need a little “extra,” the Bee Stinger™ stabilizer extensions provide the option to lengthen
Bee Stinger™ mounts come in various styles featuring rugged design to support any length and your existing stabilizer for further customization.
weight of side bar. Tight tolerances and heavy duty locking screws assure a tight no-slip fit.

QUICK DISCONNECT STANDARD: QUICK DISCONNECT

10 DEGREE ANGLE:
• Mounts directly to bow, with or
without use of side bar or V-bar mount.
• Mounts directly to bow, with or
without use of side bar or V-bar mount. ALUMINUM EXTENSIONS COME
• 10 degree down angle offers extra IN 3”, 4”, AND 5” LENGHTS
1” EYE BOLT
stability
V-BAR BLOCK MOUNTS:
V-BAR ADJUSTABLE- NARROW: V-BAR ADJUSTABLE- WIDE:
• Locking Teeth engagement • Locking Teeth engagement
• Dual angle adjust on left and right • Dual angle adjust on left and right
V-bar mounts V-bar mounts

V-BAR ADJUSTABLE ELITE: V-BAR SOLID:

• Locking Teeth engagement • Fixed angle
• Dual angle adjust on left and right • Side bar quick disconnects
V-bar mounts
• Front and side bar quick disconnects

SIDE BAR MOUNTS:

SIDE BAR INFINITY: ADJUSTABLE-ELITE:

• No Locking Teeth for infinite • Locking Teeth engagement
adjustment • Front and Side bar quick disconnect
• Side bar quick disconnect • Dual angle adjustment
• Dual angle adjustment

ADJUSTABLE-STANDARD: ADJUSTABLE-ELITE WITHOUT

• Locking Teeth engagement QUICK DISCONNECT:
• Single angle adjustment • Locking Teeth engagement
• Side bar quick disconnect
• Dual angle adjustment

MICROHEX™ DOVETAIL:
• Side bar quick disconnect

72 • Dual angle adjustment

800.551.0541 • BEESTINGER.COM 73
 END WEIGHTS
STANDARD END WEIGHTS:

1/3 OZ. ALUMINUM END WEIGHT 1 OZ. STAINLESS STEEL END WEIGHT 4 OZ. STAINLESS STEEL END WEIGHT 8 OZ. STAINLESS STEEL END WEIGHT
The 1/3 oz. Aluminum end weights allow The stainless steel 1 oz. end weights Single block 4 oz. stainless steel end weight This single block 8 oz. stainless steel end weight
every class of shooter to micro-tune any provide customized balance to any provides optimum balance and stabilization for is designed for the archer who wants extra
Bee Stinger™ Stabilizer. hunting or target bow. any Bee Stinger™ Stabilizer. weight without having to stack multiple single
—2 Pack —3 Pack weights on the bar. Maximum convenience,
maximum balance and stability.
AVAILABLE COLOR: AVAILABLE COLORS: AVAILABLE COLORS:
POLISHED ALUMINUM ONLY STAINLESS, MATTE BLACK, GREEN, RED STAINLESS, MATTE BLACK, GREEN, RED AVAILABLE COLORS:
STAINLESS, MATTE BLACK

PRO HUNTER MAXX END WEIGHTS:

Designed to meet the exacting standards of the world’s leading archers,
the Pro Hunter Maxx end weights provide maximum balance and stability
for your Bee Stinger™ Stabilizer system.

PLASTIC WEIGHT CAP

FITS FREESTYLE AND

SPORT HUNTER EXTREME
WEIGHTS

2 OZ. ALUMINUM 4 OZ. STEEL

74 800.551.0541 • BEESTINGER.COM 75
 CUSTOM ACCESSORIES LOGO WEAR
DE-RESONATORS: TO SEE THE FULL LINE OF BEE STINGER
APPAREL VISIT BEESTINGER.COM
The De-Resonator allows archers to cancel much of the resonant vibration that occur in some bow
set-ups. Simply move the De-Resonator up or down the stabilizer bar to the desired location.

BLACK
BEE STINGER HATS

ENHANCERS:
The Enhancer is used on the end of the front bar to offer vibration Damping as well as a soft feel when T-SHIRTS:
placing the bar on the ground. SIZES: SM, MD, LG, XL, 2X, 3X

BLACK PINK GREEN ORANGE YELLOW RED BLUE PURPLE

MICROHEX™ DAMPERS:

BEE STINGER HOODIE BEE STINGER

SHOOTER JERSEY

BLACK PINK GREEN ORANGE YELLOW RED BLUE PURPLE

WINDOW DECAL:
2in x 6in

76 BEE STINGER T-SHIRTS 800.551.0541 • BEESTINGER.COM 77

 TECHNICAL SPECIFICATIONS STABILIZER MODEL - TARGET/FREESTYLE LENGTH WEIGHT INCLUDED TOTAL TOTAL LENGTH
(BAR ONLY) (BAR ONLY) WEIGHT(S) WEIGHT INCL. (3) WEIGHTS
Competitor - 12” - V-Bar* 12” 3.63 oz n/a n/a n/a
STABILIZER MODEL - HUNTING LENGTH WEIGHT INCLUDED TOTAL TOTAL LENGTH
(BAR ONLY) (BAR ONLY) WEIGHT(S) WEIGHT INCL. (3) WEIGHTS Competitor - 15” - V-Bar* 15” 4.05 oz n/a n/a n/a
MicroHex- 6” 6” 2.97 oz (3) 1 oz 5.97 oz 6.50” Premier Plus - 20” - WindBar 20” 4.79 oz (2) 1 oz, 10.79 oz 21”
MicroHex- 8” 8” 3.22 oz (3) 1 oz 6.22 oz 8.50” (1) 4 oz
MicroHex- 10” 10” 3.47 oz (3) 1 oz 6.47 oz 10.50” Premier Plus - 24” 24” 5.28 oz (3) 1 oz 8.28 oz 24.5”
MicroHex - Counterslide - 10” 10” 5.15 oz (5) 1 oz 10.15 oz 10.50” Premier Plus - 27” 27” 5.77 oz (3) 1 oz 8.77 oz 27.5”
MicroHex - Counterslide Dovetail - 10” 10” 7.17 oz (5) 1 oz 12.17 oz 10.50” Premier Plus - 30” 30” 6.17 oz (3) 1 oz 9.17 oz 30.5”
MicroHex - Counterslide - 12” 12” 5.40 oz (5) 1 oz 10.40 oz 12.50” Premier Plus - 33” 33” 6.57 oz (3) 1 oz 9.57 oz 33.5”
MicroHex - Counterslide Dovetail - 12” 12” 7.42 oz (5) 1 oz 12.42 oz 12.50” Premier Plus - 36” 36” 6.98 oz (3) 1 oz 9.98 oz 36.5”
Premier Plus - 10” - V-Bar* 10” 3.4 oz n/a n/a n/a
MicroHex - Counterslide - 15” 15” 5.77 oz (5) 1 oz 10.77 oz 15.50”
Premier Plus - 12” - V-Bar* 12” 3.62 oz n/a n/a n/a
MicroHex - Counterslide Dovetail - 15” 15” 7.79 oz (5) 1 oz 12.79 oz 15.50”
Premier Plus - 15” - V-Bar* 15” 4.01 oz n/a n/a n/a
Sport Hunter Xtreme - 6” 6” 3.85 oz* (3) 1 oz 6.85 oz 6.50”
* Does NOT include Weights
Sport Hunter Xtreme - 8” 8” 4.18 oz* (3) 1 oz 7.18 oz 8.50”
Sport Hunter Xtreme -10” 10” 4.45 oz* (3) 1 oz 7.45 oz 10.50” WEIGHTS TOTAL TOTAL DIAME-
Sport Hunter Xtreme - Counterslide - 10” 10” 4.45 oz* (5)1 oz 9.45 oz 10.50” (ALL WEIGHTS THREADED FOR 5/16 - 24) THICKNESS WEIGHT TER
Sport Hunter Xtreme - Counterslide - 12” 12” 4.63 oz* (5)1 oz 9.63 oz 12.50” Freestyle/Sport Htr/MicroHex - Weight - 1/3oz .165” .33 oz n/a 1.35”
Sport Hunter Xtreme - Counterslide - 15” 15” 4.90 oz* (5)1 oz 9.90 oz 15.50” Freestyle/Sport Htr/MicorHex - Weight - 1oz .165” 1 oz n/a 1.35”
Pro Hunter Maxx - 8” ** 8” 4.18 oz* (2)4 oz & (1)2 14.18 oz 8.574” Freestyle/Sport Htr/MicroHex - Weight - 4oz .660” 4 oz n/a 1.35”
oz Freestyle/Sport Htr/MicroHex - Weight - 8oz 1.32” 8 oz n/a 1.35”
Pro Hunter Maxx - 10” ** 10” 4.45 oz* (2)4 oz & (1)2 14.45 oz 10.574” Pro Hunter Maxx - Weight - 2oz .25” 2 oz n/a 2.66”
oz Pro Hunter Maxx - Weight - 4oz .162” 4 oz n/a 2.66”
Pro Hunter Maxx - 12” ** 12” 4.63 oz* (2)4 oz & (1)2 14.63 oz 12.574”
ACCESSORIES TOTAL TOTAL TOTAL DIAME-
oz
LENGTH WEIGHT WIDTH TER
* Includes Deresonator
Quick Disconnect - 10 Degree Down Angle 1.191” 1.15 oz n/a 1”
** Fully adjustable in 2oz / 4oz / 6oz / 8oz or 10 oz weight configurations
Quick Disconnect - Standard 1.125” 1.02 oz n/a .96”
STABILIZER MODEL - TARGET/FREESTYLE LENGTH WEIGHT INCLUDED TOTAL TOTAL LENGTH Side Bar - Adjustable - STD .375”* 2.38 oz 2”** n/a
(BAR ONLY) (BAR ONLY) WEIGHT(S) WEIGHT INCL. (3) WEIGHTS Side Bar - Adjustable - ELITE without front QD .375”* 3.1 oz 2”** n/a
MicroHex - 20” - WindBar 20” 4.51 oz (2) 10 oz, (1) 10.51 oz 21”
Side Bar - Infinity .375”* 3.1 oz 2”** n/a
4 oz
MicroHex - 24” 24” 5.01 oz (3) 1 oz 8.01 oz 24.5” Side Bar - Adjustable - ELITE 1.1”* 3.73 oz 2”** n/a
MicroHex - 27” 27” 5.38 oz (3) 1 oz 8.38 oz 27.5” V-Bar Block - Adjustable - STD .75”* 6.43 oz 1.8”** n/a
MicroHex - 30” 30” 5.75 oz (3) 1 oz 8.75 oz 30.5” V-Bar Block - Adjustable - STD - Wide .75”* 7.49 oz 2.8”** n/a
MicroHex - 33” 33” 6.12 oz (3) 1 oz 9.12 oz 33.5” V-Bar Block - Adjustable - ELITE 1.063”* 5.16 oz 2.8”** n/a
MicroHex - 36” 36” 6.49 oz (3) 1 oz 9.49 oz 36.5” MicroHex Counterslide Bracket .375” 1.58 oz 2.3” n/a
MicroHex - 10” - V-Bar* 10” 3.27 oz n/a 3.27 oz n/a (not sold seperately)
MicroHex - 12” - V-Bar* 12” 3.52 oz n/a 3.52 oz n/a MicroHex Counterslide Bracket - with QD .9” 3.6 oz 1.2” - 2.5” n/a
MicroHex - 15” - V-Bar* 15” 3.89 oz n/a 3.89 oz n/a (not sold seperately)
Competitor - 20” - WindBar 20” 4.71 oz (2) 1 oz, 10.71 oz 21” Sport Hunter Xtreme Counterslide Bracket .375” 1.31 oz 2.3” n/a
(1) 4 oz (not sold seperately)
Competitor - 24” 24” 5.26 oz (3) 1 oz 8.26 oz 24.5” MicroHex Damper 1.25” .55 oz n/a 1.44”

Competitor - 27” 27” 5.61 oz (3) 1 oz 8.61 oz 27.5” Deresonator 1.42” 1.07 oz n/a 1.47”

Competitor - 30” 30” 5.85 oz (3) 1 oz 8.85 oz 30.5” FreeStyle Enhancer 1.43” 1.14 oz n/a 1.63”

Competitor - 33” 33” 6.51 oz (3) 1 oz 9.51 oz 33.5” Extension - 1” Eye Bolt 1.125” .9 oz n/a .875”

Competitor - 36” 36” 6.86 oz (3) 1 oz 9.86 oz 36.5” Extension - Aluminum - 3” 3” 2.4 oz n/a .9”

Competitor - 10” - V-Bar* 10” 3.38 oz n/a n/a n/a Extension - Aluminum - 4” 4” 3.1 oz n/a .9”
Extension - Aluminum - 5” 5” 3.7 oz n/a .9”

78
* Measurement of added thickness between bar and bow mount
** Widths are measured from centerlines of stabilizers, not overall width of part 800.551.0541 • BEESTINGER.COM
G O LDT I P.C O M B EEST I N G ER.C O M

604 FIRST STREET

FLORA, MS 39110
800.551.0541
LI T# B S CATA LO G1 8