Asme B107.2-2002

Download as pdf or txt
Download as pdf or txt
You are on page 1of 29

--``-`-`,,`,,`,`,,`---

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
The American Society of
Mechanical Engineers

A N A M E R I C A N N A T I O N A L S T A N D A R D

SOCKET WRENCHES,
EXTENSIONS, ADAPTORS,
AND UNIVERSAL JOINTS
POWER DRIVE QMPAD~
(INNI SERIES)

ASME B107.!-!00!
(Revision of USME BlO7.2-1195)
--``-`-`,,`,,`,`,,`---

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
Date of Issuance: January 31, 2003

This Standard will be revised when the Society approves the issuance of a
new edition. There will be no addenda issued to this edition.

ASME issues written replies to inquiries concerning interpretations of


technical aspects of this Standard. Interpretations are published on the ASME

--``-`-`,,`,,`,`,,`---
Web site under the Committee Pages at http://www.asrne.org/codes/ as they
are issued.

ASME is the registered trademark of The American Society of Mechanical Engineers.

This code or standard was developed under procedures accredited as meeting the criteria for
American National Standards. The Standards Committee that approved the code or standard
was balanced to assure that individuals from competent and concerned interests have had an
opportunity to participate. The proposed code or standard was made available for public review
and comment that provides an opportunity for additional public input from industry, academia,
regulatory agencies, and the public-at-large.
ASME does not "approve," "rate," or "endorse" any item, construction, proprietary device,
or activity.
ASME does not take any position with respect to the validity of any patent rights asserted in
connection with any items mentioned in this document, and does not undertake to insure anyone
utilizing a standard against liabilityfor infringement of any applicable letters patent, nor assumes
any such liability. Users of a code or standard are expressly advised that determination of the
validity of any such patent rights, and the risk of infringement of such rights, is entirely their
own responsibility.
Participation by federal agency representative(s) or person(s) affiliated with industry is not to
be interpreted as government or industry endorsement of this code or standard.
ASME accepts responsibility for only those interpretations of this document issued i n
accordance with the established ASME procedures and policies, which precludes the issuance
of interpretations by individuals.

No part of this document may be reproduced in any form,


in an electronic retrieval system or otherwise,
without the prior written permission of the publisher.

The American Society of Mechanical Engineers


Three Park Avenue, New York, NY 10016-5990

Copyright O 2003 by
THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS
All Rights Reserved
Printed in U.S.A.

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
CONTENTS

Foreword ............................................................................ V

Committee Roster .................................................................... vi


Correspondence With the B 107 Committee .............................................. vii
1 Scope .......................................................................... 1
2 Classification ................................................................... 1
3 Normative References ......................................................... 1
4 Requirements .................................................................. 1
5 Test Procedures ................................................................ 6
6 Designations ................................................................... 8
Figures
1 Type I. II. and VII Sockets. Class 1. Regular Length; Class 2. Long Length ....... 3
2 Type III. Universal Sockets. Single Hexagon (6-Point) and Double Hexagon
(12-Point) ..................................................................... 4
3 Type IV Bar. Extension .......................................................... 4
4 Type V. Adaptor ................................................................ 4
5 Type VI. Universal Joint ......................................................... 4
Tables
1 Type I. Class 1 and 2. Single Hexagon (6-Point) and Double Hexagon
(12.Point). Regular and Long Length. '/4 in. Drive .............................. 5
2 Type I. Class 1. 2. and 3. Single Hexagon (6-Point) and Double Hexagon
(12.Point). Regular. Long. and Extra Long Length. 3/s in. Drive ................. 5
3 Type I. Class 1. 2. and 3. Single Hexagon (6-Point) and Double Hexagon
(12.Point). Regular. Long. and Extra Long Length. 1/2 in. Drive ................. 6
4 Type I. Class 1 and 2. Single Hexagon (6-Point) and Double Hexagon
(12.Point). Regular and Long Length. 3/4 in. Drive .............................. 7
5 Type I. Class 4 and 5 . Single Hexagon (6-Point) and Double Hexagon
(12.Point). Regular and Long Length. Thin Wall. 1/2 in . Drive ................... 8
6 Type I. Class 4. Single Hexagon (6-Point) and Double Hexagon (12.Point).
Regular Length. Thin Wall. 3/4 in. Drive ........................................
--``-`-`,,`,,`,`,,`---

9
7 Type I. Class 1 and 2. Single Hexagon (6-Point) and Double Hexagon
(12.Point). Regular and Long Length. 1 in. Drive ............................... 10
8 Type VII. Class 1 and 2. Single Hexagon (6-Point) and Double Hexagon
(12.Point). Regular and Long Length. #5 Spline Drive .......................... 11
9 Type I. Class 1 and 2. Single Hexagon (6-Point) and Double Hexagon
(12.Point). Regular and Long Length. l1I2 in. Drive ............................. 12
10 Type I. Class 1. Single Hexagon (6.Point). Regular Length. 2l/2 in. Drive .......... 13
11 Type II. Class 1 and 2. Single Square (4-Point) and Double Square @.Point).
Regular and Long Length. 3/8 in. Drive ......................................... 14

iii

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
12 Type II. Class 1 and 2. Single Square (4-Point) and Double Square (8.Point).
Regular and Long Length. '/2 in . Drive ......................................... 14
13 Type II. Class 1 and 2. Single Square (4-Point) and Double Square (8.Point).
Regular and Long Length. 3/4 in. Drive ......................................... 15
14 Type III. Class 1 and 2. Universal. Single Hexagon (6-Point) and Double
Hexagon (12.-Point), Regular and Long Length. 3/s in. Drive ..................... 15
15 Type III. Class 1 and 2. Universal. Single Hexagon (6-Point) and Double
Hexagon (12.Point). Regular and Long Length. '/2 in. Drive ..................... 16
16 Type IV. Bar. Extension ......................................................... 16
17 Type V. Adaptor ................................................................ 16
18 Type VI. Universal Joint ......................................................... 16
19 Hexagon Mandrel Dimensions and Maximum Depth of Mandrel Insertion ........... 17
20 Square Mandrel Dimensions ...................................................... 18

--``-`-`,,`,,`,`,,`---

iv

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
The American National Standards Committee B107, Socket Wrenches and Drives, under
sponsorship of The American Society of Mechanical Engineers (ASME), was reorganized
as an ASME Standards Committee, and its title was changed to Hand Tools and Accessories.
The purposes of this Standard are to define general and dimensional data specifically
applicable to detachable socket wrenches and to specify test methods to evaluate performance
relating to the defined requirements.
This Standard is a revision of B107.2-1995 Socket Wrenches, Extensions, Adaptors, and
Universal Joints, Power Drive (impact) (Inch Series). A principal change in this edition of
the Standard is the use of Type and Class designations in place of Class and Style designations,
in accordance with other B107 Standards. Updated references, finish requirements, and
dimensional data are included.
The format of this Standard is in accordance with The ASME Codes & Standards Writing
Guide 2000. Requests for interpretations of the technical requirements of this Standard
should be expressed in writing to the Secretary, B107 Committee, at the address below.
Suggestions for the improvement of this Standard are welcome. They should be addressed
to the The American Society of Mechanical Engineers, Secretary, B107 Standards Committee,
Three Park Avenue, New York, NY 10016-5990.
The requirements of this Standard become effective at the time of publication. This
revision was approved as an American National Standard on May 13, 2002.

--``-`-`,,`,,`,`,,`---

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
ASME STANDARDS COMMITTEE BI07
Hand Tools and Accessories

(The following is the roster of the Committee at the time of approval of this Standard.)

OFFICERS
R. R. McCuiiough, Chair
G. E. Olson, Vice Chair
J. R. Bird, Secretary

COMMITTEE PERSONNEL
J. R. Bird, The American Society of Mechanical Engineers
J. D. Davidcon, Sears Roebuck and Co.
J. S. Foote, Trade Association Management, Inc.
A. Herskovitz, Consultant
H. Kimbali, Naval Air Warfare Center
R. R. McCullough, Consultant
D. S. McKittrick, Western Forge
G. E. Olson, Gene Olson Engineering Consultant, Ltd.
W. T. Pagac, Snap-on, Inc.
D. M. Eggert, Alternate, Snap-on, Inc.
J. M.Ster, General Services Administration
I. I. Harding, Alternate, General Services Administration
R. B. Wright, Wright Tool Co.
W. C. Snyder, Alternate, Wright Tool Co.

SUBCOMMITTEE 1 - SOCKETS AND


ATTACHMENTS
R. B. Wright, Chair, Wright Tool Co.
J. D. Davidson, Sears Roebuck and Co.
D. M. Eggert, Snap-on, Inc.

vi
--``-`-`,,`,,`,`,,`---

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
General. ASME Standards are developed and maintained with the intent to represent the
consensus of concerned interests. As such, users of this Standard may interact with the
Committee by requesting interpretations, proposing revisions, and attending Committee
meetings. Correspondence should be addressed to:
Secretary, B107 Standards Committee
The American Society of Mechanical Engineers
Three Park Avenue
New York, NY 10016-5990

Proposing Revisions. Revisions are made periodically to the Standard to incorporate


--``-`-`,,`,,`,`,,`---

changes that appear necessary or desirable, as demonstrated by the experience gained from
the application of the Standard. Approved revisions will be published periodically.
The Committee welcomes proposals for revisions to this Standard. Such proposals should
be as specific as possible, citing the paragraph number(s), the proposed wording, and a
detailed description of the reasons for the proposal, including any pertinent documentation.
Interpretations. Upon request, the B107 Committee will render an interpretation of any
requirement of the Standard. Interpretations can only be rendered in response to a written
request sent to the Secretary of the B107 Standards Committee.
The request for interpretation should be clear and unambiguous. It is further recommended
that the inquirer submit hisher request in the following format:
Subject: Cite the applicable paragraph number(s) and the topic of the inquiry.
Edition: Cite the applicable edition of the Standard for which the interpretation
is being requested.
Question: Phrase the question as a request for an interpretation of a specific
requirement suitable for general understanding and use, not as a request
for an approval of a proprietary design or situation. The inquirer may
also include any plans or drawings, which are necessary to explain
the question; however, they should not contain proprietary names or
information.
Requests that are not in this format may be rewritten in the appropriate format by the
Committee prior to being answered, which may inadvertently change the intent of the
original request.
ASME procedures provide for reconsideration of any interpretation when or if additional
information that might affect an interpretation is available. Further, persons aggrieved by
an interpretation may appeal to the cognizant ASME Committee or Subcommittee. ASME
does not “approve,” “certify,” “rate,” or “endorse” any item, construction, proprietary device,
or activity.
Attending Committee Meetings. The B107 Standards Committee regularly holds meetings,
which are open to the public. Persons wishing to attend any meeting should contact the
Secretary of the B107 Standards Committee.

Vii

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
ASME B107.2-2002

SOCKET WRENCHES, EXTENSIONS, ADAPTORS,


AND UNIVERSAL JOINTS, POWER DRIVE [IMPACT)
(INCH SERIES)

1 SCOPE this Standard are encouraged to investigate the possibii-


ity of applying the most recent edition of the documents
This Standard is intended to cover the complete
indicated below.
general and dimensional data for detachable socket
wrenches, extensions, adaptors, and universal jints for ASME B107.4M-1995, Driving and Spindle Ends for
power drive impact use. Inclusion of dimensional data Portable Hand, Impact, Air and Electric Tools (per-
in this Standard is not intended to imply that ail of cussion tools excluded)
the products described herein are stock production sizes. ASME B107.17M-1997, Gages, Wrench Openings, Ref-
Consumers are requested to consult with manufacturers erence
concerning lists of stock production sizes.
Publisher: The American Society of Mechanical Engi-
All dimensions in this Standard are in inches.
neers (ASME International), Three Park Avenue,
New York, NY 10016-5990; Order Department: 22
2 CLASSIFICATION Law Drive, PO Box 2300, Fairfield, NJ 07007-2300
Type I: Sockets, single (6-point) and double ASTM E 18-97a, Standard Test Methods for Rockwell
(12-point) hexagon Hardness and Rockwell Superficial Hardness of Me-
Class I : Regular length taiiic Materials
Class 2: Long length
Publisher: American Society for Testing and Materials
Class 3: Extra long length (ASTM), 100 Barr Harbor Drive, West Consho-
Class 4: Regular length, thin wall hocken, PA 19428-2959
Class 5: Long length, thin wall
Type II: Sockets, single square (4-point) and
double square (8-point)
Class I : Regular length 4 REQUIREMENTS
Class 2: Long length
Type m: Universal sockets, single hexagon (6- 4.1 Illustrations
--``-`-`,,`,,`,`,,`---

point) and double hexagon (12-point) The illustrations shown herein are descriptive and
Class 1: Regular length not restrictive, and are not intended to preclude the
Class 2: Long length manufacture of sockets and attachments that are other-
Type IV: Bars, extension wise in accordance with this Standard.
Type V: Adaptors
Type VI: Universal joint
4.2 Materials
Type VII: Sockets, #5 Spline Drive
Class I : Regular length Unless otherwise specified, the material used in the
Class 2: Long length tools shall be steel, the chemical composition and heat
treatment of which shail be such as to produce tools
conforming to the requirements hereinafter specified.
3 NORMATIVE REFERENCES
The following documents form a part of this Standard
4.3 Dimensions
to the extent specified herein. At the time of publication,
the editions indicated were valid. All standards are Dimensions shall be in accordance with applicable
subject to revision, and parties to agreements based on tables.

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
SOCKET WRENCHES, EXTENSIONS, ADAPTORS,
ASME B107.2-2002 AND UNIVERSAL JOINTS, POWER DRIVE (IMPACT) (INCH SERIES)

4.4 Markings 4.8.2.2 Oxide Coating. The coating shall consist


of a chemically produced oxide coating followed with
Sockets and attachments shall be marked in a plain
a coating of a rust preventative.
and permanent manner with the manufacturer's name
or with a trademark of such known character that the
source of manufacture and country of origin may be 4.9 Bolt Clearance Hole
readily determined. In addition, sockets shall be marked
A bolt clearance hole shall be provided in all sockets
in a plain and permanent manner with the nominal
except Type III, universal sockets detailed in para.
size of the wrench opening (distance across flats) for
4.9.1. The minimum depth of the bolt clearance hole
the nut, bolt, or screw end.
shall be 1.5 times the minimum depth of the nut
opening as set forth in the respective tables for regular
4.5 Proof Torque length sockets and not less than 55% of the overall
When tested as specified, sockets and extensions length for long length and extra long length sockets
shall withstand the proof torque specified in the applica- as measured from the face of the wrench end. The
ble tables without failure or permanent deformation size of the bolt clearance hole shall be in accordance
(set) that might affect the durability or serviceability with that of the applicable size socket specified in the
of the wrenches. respective tables for each class and style.

4.6 Hardness 4.9.1 A bolt clearance hole may be provided in


Type III, Class 1 and 2, universal sockets. The diameter
Sockets and attachments shall be hardened and shall of the hole if provided shall be in accordance with
have a hardness value for the various sizes within the the applicable size socket as specified in Tables 14
range shown in the table below except that the maximum and 15.
hardness for Type I Class 4 and 5 shall be 52 HRC.
HRC 4.10 Through Hole
Drive Size,
in. -
Min. -
Max.
A through hole having a minimum diameter equal
38 55 to 50% of the square drive size or equal to the bolt
38 55 clearance hole diameter, whichever is smaller, shall be
38 52
35 50
provided.
35 50
28 42
4.1I Internal Drive Opening
--``-`-`,,`,,`,`,,`---

Ail internai drive openings shall be well defined.


4.7 Wrench Opening The openings shall conform to ASME B107.4M.
Wrench opening tolerances shall be such as to ensure
acceptance when used with gages conforming to ASME 4.12 Countersink of Nut End Socket Opening
B 107.17M.
If countersunk, the nut end socket opening shaIl be
4.8 Finish countersunk with an included angle of 85 deg to 155
deg and a minimum diameter equal to the across-
4.8.1 Surface. Ail extemal surfaces shall be free comers dimension of the opening.
from pits, nodules, burrs, cracks, and other detrimental
defects affecting serviceability.
4.13 External Corners
4.8.2 Coatings. The coatings shall be adherent, External comers shall be broken with no sharp edges.
smooth, continuous, and free from uncoated areas.
Sockets and attachments shall have one of the following
coatings. 4.14 Type I -
Socket, Single Hexagon (6-
Point) and Double Hexagon (12-Point)
4.8.2.1 Phosphate Coating. The coating shall
consist of a chemically produced phosphate coating Sockets shall conform to Tables 1 through 7, Table
followed with a coating of a rust preventative. 9. and Table 10.

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
SOCKET WRENCHES, EXTENSIONS, ADAPTORS,
AND UNIVERSAL JOINTS, POWER DRIVE (IMPACT) (INCH SERIES) ASME 8107.2-2002

D
I
II E C
I

Type 1, II Type I Type I


Single Hexagon Double Hexagon

t
Type VI1
L I I
Type II Type II
Single Square Double Square

GENERAL NOTES:
(a) A shall be equal to or greater than nut opening depth in applicable tables.
(b) Maximum nut end diameter of socket C shall not be exceeded for length B and shall conform to applicable tables.
(c) B length shall be greater than or equal to the minimum nut opening depth A in applicable tables.

FIG. 1 TYPE I, II, AND VI1 SOCKETS, CLASS 1, REGULAR LENGTH;


CLASS 2, LONG LENGTH

3
--``-`-`,,`,,`,`,,`---

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
SOCKET WRENCHES, EXTENSIONS, ADAPTORS,
ACME 8107.2-2002 AND UNIVERSAL JOINTS, POWER DRIVE (IMPACT) (INCH SERIES)

Shape optional

Square Single Double


Drive Hexagon Hexagon

GENERAL NOTES:
(a) A shall be equal to or greater than nut opening depth in applicable tables.
(b) Maximum nut end diameter of socket C shall not be exceeded for length 6 and shall conform to applicable tables.
(c) B length shall be greater than or equal to the minimum nut opening depth A in applicable tables.
(d) D is the outside diameter, drive end, and shall conform to applicable tables.

FIG. 2 TYPE 111, UNIVERSAL SOCKETS, SINGLE HEXAGON (6-POINT)


AND DOUBLE HEXAGON (12-POINT)

FIG. 3 TYPE IV, BAR EXTENSION

FIG. 4 TYPE V, ADAPTOR FIG. 5 TYPE VI, UNIVERSAL JOINT


--``-`-`,,`,,`,`,,`---

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
SOCKET WRENCHES, EXTENSIONS, ADAPTORS,
AND UNIVERSAL JOINTS, POWER DRIVE (IMPACT) (INCH SERIES) ASME 8107.2-2002

TABLE 1 TYPE I, CLASS 1 AND 2, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON
--``-`-`,,`,,`,`,,`---

(12-POINT), REGULAR AND LONG LENGTH, in. DRIVE


Outside Diameter, in.
Nut Bolt Clearance
Overall Length, in. Nut End, Drive End, Opening Hole Proof
C D Depth, Diameter, Torque,
Nominal Regular, Long, A E Ibf-in.,
Opening, in. Max. Min. Min. Max. Min. Max. in., Min. in., Min. Min.
3 0.435 0.510 0.110 0.130 95
116 1.010 1.goo 0.285 0.320
'132 1.010 1.goo 0.325 0.360 0.435 0.510 O. 125 0.130 135
'14 1.010 1.goo 0.360 0.424 0.440 0.510 O. 125 0.150 190
9 0.400 0.490 0.450 0.510 0.125 0.171 250
132 1.010 1.goo
7
16 1.010 1.goo 0.440 0.502 0.470 0.510 0.125 0.171 320

1 1132 1.010 1.900 0.475 0.535 0.490 0.535 O. 170 0.203 400
318 1.010 1.900 0.510 0.580 0.515 0.580 0.219 0.281 500
'4 6 1.010 1.900 0.590 0.660 0.550 0.660 0.219 0.281 500
5; 1.010 1.900 0.665 0.737 0.550 0.730 0.281 0.344 500
9116 1.010 1.900 0.740 0.815 0.550 0.780 0.281 0.406 500

TABLE 2 TYPE I, CLASS 1,2 AND 3, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON
(12-POINT), REGULAR, LONG, AND EXTRA LONG LENGTH, in. DRIVE /'*
Outside Diameter, in.
Nut Bolt Clearance
Overall Length, in. Nut End, Drive End, Opening Hole Proof
Long C D Depth, Diameter, Torque,
Nominal Regular, Extra Long, A E Ibf-in.,
Opening, in. Max. Min. Max. Min. Min. Max. Min. Max. in., Min. in., Min. Min.

%6 1.187 1.688 2.500 ... 0.471 0.515 0.677 0.760 0.102 0.171 440
l132 1.187 1.688 2.500 ... 0.490 0.552 0.677 0.760 0.117 0.203 550
1.187 1.688 2.500 2.688 0.527 0.605 0.677 0.760 0.117 0.281 660
'
i61 1.187 1.688 2.500 2.688 0.613 0.697 0.677 0.760 0.203 0.281 930
'12 1.187 1.688 2.500 2.688 0.693 0.823 0.700 0.823 0.209 0.344 1240

9 1.250 1.938 2.750 3.250 0.771 0.885 0.771 0.885 0.249 0.406 1600
/16
78 1.250 1.938 2.750 ... 0.860 0.948 0.860 0.948 0.281 0.469 2000
11
116 1.250 1.938 2.750 ... 0.860 1.031 0.865 1.031 0.318 0.469 2200
Y4 1.250 1.938 2.750 ... 1.021 1.073 0.865 1.073 0.356 0.531 2200

4.15 Type II -
Sockets, Single Square (4- joints shall be provided with a friction type tension
Point) and Double Square (&Point) device which will hold the drive end and socket or
tang end in any set position with a force adequate to
Sockets shall be similar to Fig. 1 and shall conform
hold the socket against gravity. The tension device
to Tables 11, 12, and 13.
shail compensate for wear. Universal sockets and univer-
sal joints shail be capable of rotation in a complete
4.16 Type 111 -
Universal Sockets, Single
revolution when the angular deviation of one member
Hexagon (6-Point) and Double Hexagon from the centerline is 20 deg and
(12-Point) and Type VI Universal - 35 deg maximum. Type III universal sockets shall be
Joints
similar to Fig.
- 2 and shall conform to Tables 14 and
Universal sockets shall be a single hexagon (6-point) 15 for the size and drive specified. Type VI universal
or double hexagon (12-point) as specified. The 3/8 in. joints shall be similar to Fig. 5 and shail conform to
and 1/2 in. drive size universal sockets and universal Table 18 for the drive specified.

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
SOCKET WRENCHES, EXTENSIONS, ADAPTORS,
ASME 8107.2-2002 AND UNIVERSAL JOINTS, POWER DRIVE (IMPACT) (INCH SERIES)

TABLE 3 TYPE I, CLASS 1,2 AND 3, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON
(itPOINT), REGULAR, LONG, AND EXTRA LONG LENGTH, I/.in. DRIVE

Outside Diameter, in.


Nut Bolt Clearance
Overall Length, in. Nut End, Drive End, Opening Hole Proof
Long C D Depth, Diameter, Torque,
Nominal Regular, Extra Long, A E I bf-in .,
Ooenina, in. Max. Min. Max. Min. Min. Max. Min. Max. in., Min. in., Min. Min.

1.800 3.187 3.688 ... 0.550 0.715 0.850 1.135 0.117 0.281 1100
1.800 3.187 3.688 ... 0.638 0.806 0.850 1.135 0.203 0.281 1500
1.800 3.187 3.688 4.938 0.726 0.897 0.850 1.135 0.209 0.344 2000
1.800 3.187 3.688 4.938 0.814 0.987 0.850 1.135 0.249 0.406 2600
1.800 3.187 3.688 4.938 0.902 1.070 0.850 1.135 0.281 0.469 3300

1.800 3.187 3.688 4.938 0.990 1.169 0.990 1.197 0.318 0.469 41 O0
1.800 3.187 3.688 4.938 1.062 1.260 1.004 1.260 0.356 0.531 5000
1.812 3.187 3.688 4.938 1.135 1.325 1.019 1.335 0.418 0.594 5000
1.960 3.187 3.688 4.938 1.207 1.390 1.033 1.410 0.479 0.594 5000
2.100 3.187 3.688 4.938 1.280 1.455 1.048 1.485 0.490 0.656 5000

2.100 3.187 3.688 4.938 1.352 1.521 1.062 1.560 0.490 0.656 5000
2.41O 3.187 3.688 4.938 1.425 1.586 1.077 1.635 0.490 0.687 5000
2.41 O 3.187 3.688 4.938 1.497 1.651 1.091 1.710 0.632 0.781 5000
2.41O 3.187 3.688 ... 1.642 1.781 1.120 1.860 0.632 0.812 5000
2.500 3.187 3.688 ... 1.789 2.197 1.120 1.906 0.748 0.906 5000

2.500 3.187 3.688 ... 1.861 2.197 1.120 1.906 0.748 0.937 5000
2.500 3.187 3.688 ... 1.933 2.322 1.120 2.031 0.748 1 .o00 5000
2.500 3.187 3.688 ... 2.005 2.387 1.120 2.156 0.847 1 .O62 5000
2.500 3.187 3.688 ... 2.075 2.445 1.120 2.250 0.847 1 .O62 5000

4.17 Type IV - Extension Bars penetrator and employing a 150 kg major load in
accordance with ASTM E 18. When surface preparation
Extension bars shall have an external square drive
is necessary, the amount of material removed in the
at one end and an internal square drive of the same
area contacted by the indicator shall not exceed:
size at the other end. The extension bar shall be similar
to Fig. 3 and shall conform to the dimensions in
Drive Size,
Table 16. in. Max. Matenal Removed

4.18 Type V - Adaptors 318, 'Iz


3/4
0.007 in.
0.015 in.
Adaptors shall have an external square drive at one 1, #5 Spline, 0.010 in. per 1 in. of diameter
end with a different size and an internal square drive or larger
at the other end. Adaptors shall be similar to Fig. 4
and shall conform to the dimensions shown in Table 17.

4.19 Type VI1 - Sockets, #I5 Spline Drive 5.2 Proof Torque Test

Sockets shall be similar to Fig. 1 and shall conform Socket wrench and drive openings shall be gaged
to Table 8. per ASME B107.17M and ASME B107.4M prior to
testing and only sockets which are in accordance with
the gage shall be tested. They shall be torqued to the
--``-`-`,,`,,`,`,,`---

5 TEST PROCEDURES proof torque using mandrel depth specified. Following


the removal of the proof torque, they shall be regaged.
5.1 Hardness Marking at mandrel contact points is allowable. Any
Conformance to the hardness range specified in para. socket which cracks, fractures, or does not gage after
4.4 shall be tested on a Rockwell tester, using a diamond torquing shall be considered to have failed the test.

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
SOCKET WRENCHES, EXTENSIONS, ADAPTORS,
AND UNIVERSAL JOINTS, POWER DRIVE (IMPACT) (INCH SERIES) ASME B107.2-2002

TABLE 4 TYPE I, CLASS 1 AND 2, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON
(12-POINT), REGULAR AND LONG LENGTH, in. DRIVE v4
Outside Diameter, in.
Nut Bolt Clearance
Overall Length, in. Nut End, Drive End, Opening Hole Proof
C D Depth, Diameter, Torque,
Nominal Regular, Long, A E Ibf-in.,
Opening, in. Max. Min. Min. Max. Min. Max. in., Min. in., Min. Min.
9 1.490 1.640 0.249 0.406 3700
16 2.125 2.937 0.990 1.010
"8 2.125 2.937 1 .O83 1.187 1.490 1.640 0.281 0.469 4400
11 5100
116 2.125 2.937 1.146 1.169 1.490 1.640 0.318 0.469
3 1.141 1.490 1.640 0.356 0.531 6000
14 2.125 2.937 1.268
13 1.490 1.640 0.418 0.594 6800
116 2.250 2.937 1.213 1.385

'18 2.250 2.937 1.285 1.635 1.490 1.640 0.479 0.594 7700
15 8700
116 2.375 2.937 1.357 1.635 1.490 1.640 0.490 0.656
1 2.375 2.937 1.429 1.635 1.490 1.71 5 0.490 0.656 9700
1% 2.500 2.937 1.501 1.701 1.520 1.790 0.490 0.687 10,800
1 118 2.500 2.937 1.621 1.760 1.550 1.865 0.632 0.781 1 1,900

1 1/4 2.625 3.187 1.740 2.1 97 1.610 2.01 5 0.632 0.812 14,200
1% 2.625 3.187 1.796 2.197 1.640 2.090 0.740 0.937 15,400
19 8 2.750 3.187 1.934 2.197 1.670 2.165 0.740 0.937 16,700
1 6 2.750 3.187 1.934 2.322 1.700 2.165 0.740 1 .O00 18,000
1 '/* 2.750 3.437 2.052 2.387 1.730 2.165 0.847 1 .O62 18,000

1946 2.750 3.437 2.075 2.445 1.730 2.165 0.847 1 .O62 18,000
1 "/e 2.750 3.437 2.240 2.51 O 1.730 2.165 0.847 1.125 18,000
11Y16 2.875 3.437 2.490 2.510 1.730 2.165 0.970 1.187 18,000
1 94 2.875 3.437 2.490 2.553 1.730 2.165 0.980 1.187 18,000
113h6 3.062 3.437 2.563 2.631 1.730 2.165 0.990 1.250 18,000

17 8 3.062 3.437 2.600 2.710 1.730 2.165 1.062 1.312 18,000


2 3.250 3.687 2.720 2.867 1.730 2.165 1 .O62 1.375 18,000
2'116 3.250 3.687 2.800 2.945 1.730 2.165 1.150 1.437 18,000
23/16 3.500 3.937 2.920 3.103 1.730 2.165 1.193 1.500 18,000
2'/4 3.500 3.937 3.000 3.181 1.730 2.165 1.276 1.562 18,000

298 3.625 4.062 3.120 3.337 1.730 2.165 1.303 1.562 18,000

5.2.1 Sockets. A square test plug of suitable universal socket assembly in the axis about which the
strength and complying with the dimensional require- load is applied.
ments of the drive tang specified in ASME B107.4M
shall be employed. The test plug may be driven by 5.2.3 Extension. Tests shall be made in the same
any suitable manual or mechanical means. The socket manner as specified in para. 5.2.1 except that the
shall then be engaged on the end of a mandrel to external drive tang shall be inserted in an internal
maximum mandrel depth in accordance with Tables 19 socket and secured in a mandrel.
and 20. Means shall be provided at the outer end of
the test plug to prevent slippage of the socket end- 5.3 Mandrels for Wrench Openings
wise from the mandrel and to keep the test pieces in
alignment. Sockets shall be tested on mandrels. Single hexagon
(6-point) or double hexagon (12-point) sockets or uni-
5.2.2 Universal Sockets. Tests shall be made in versal sockets shall be tested on hexagonal mandrels
the same manner as specified in para. 5.2.1 except that conforming to Table 19. Single square (4-point) or
means shall be provided to keep the parts of the double square (8-point) sockets shall be tested on square

7 --``-`-`,,`,,`,`,,`---

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
SOCKET WRENCHES, EXTENSIONS, ADAPTORS,
ASME 8107.2-2002 AND UNIVERSAL JOINTS, POWER DRIVE (IMPACT) (INCH SERIES)

TABLE 5 TYPE I, CLASS 4 AND 5, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON
(12-POINT), REGULAR AND LONG LENGTH, THIN WALL, '/2 in. DRIVE

Outside Diameter, in.


Nut Bolt Clearance
Overall Length, in. Nut End, Drive End, Opening Hole Proof
C D Depth. Diameter, Torque,
Nominal Regular, Long, A E Ibf-in.,
Opening, in. Max. Min. Min. Max. Min. Max. in., Min. in., Min. Min.

2.000 3.187 0.556 0.636 0.850 1.135 0.117 0.281 1100


2.000 3.187 0.633 0.713 0.850 1.135 0.203 0.281 1500
2.000 3.187 0.711 0.791 0.850 1.135 0.209 0.344 2000
2.000 3.187 0.788 0.868 0.850 1.135 0.249 0.406 2600
2.000 3.187 0.866 0.946 0.850 1.135 0.281 0.469 3300

2.000 3.187 0.944 1 .O24 0.964 1.197 0.318 0.469 4100


2.000 3.187 1 .o20 1.100 1 .O04 1.260 0.356 0.531 5000
2.000 3.187 1 .O98 1.158 1 .o19 1.335 0.418 0.594 5000
2.000 3.187 1.175 1.255 1 .O33 1.41O 0.479 0.594 5000
2.000 3.187 1.253 1.333 1 .O48 1.485 0.490 0.656 6000

2.500 3.187 1.330 1.410 1 .O62 1.560 0.490 0.656 5000


2.500 3.187 1.408 1.488 1 .O77 1.635 0.490 0.687 5000
2.500 3.187 1.485 1.565 1 .o91 1.710 0.632 0.781 5000
2.500 3.187 1.563 1.643 1.105 1.785 0.632 0.796 5000
2.500 3.187 1.640 1.720 1.120 1.860 0.632 0.812 5000

2.500 3.187 1.718 1.798 1.120 1.860 0.748 0.906 5000


2.500 3.187 1.795 1.875 1.120 1 .E60 0.748 0.937 5000
2.500 3.187 1.872 1.952 1.120 2.000 0.748 1 .o00 5000
2.500 3.187 1.950 2.030 1.120 2.000 0.847 1 .O62 5000
2.500 3.187 2.028 2.108 1.120 2.000 0.847 1 .O62 5000

mandrels conforming to Table 20. All mandrels shall fe) Type


be hardened to not less than 56 HRC and shail be (ú) Class
smoothly finished. (e) Wrench opening size and configuration (when
applicable)
EXAMPLES: Power drive (impact) socket, 5; in. drive size, Type
6 DESIGNATIONS I, Class 1, 3/4 in. opening, single hexagon.
Sockets shall be designated by the following data Power drive (impact) socket, '/4 in. drive size, Type I, Class 1, 11/8
in the sequence shown: in. opening, double hexagon
(a) Power drive (impact) socket Power drive (impact) extension bar, '/4 in. drive size, Type IV, 7
(b) Drive size in. length --``-`-`,,`,,`,`,,`---

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
SOCKET WRENCHES, EXTENSIONS, ADAPTORS,
AND UNIVERSAL JOINTS, POWER DRIVE (IMPACT) (INCH SERIES) ASME B107.2-2002

TABLE 6 TYPE I, CLASS 4, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON


(12-POINT), REGULAR LENGTH, THIN WALL, y4 in. DRIVE
Outside Diameter, in.
Nut Boit Clearance
Overall Nut End, Drive End, Opening Hole Proof
Length, C D Depth, Diameter, Torque,
NominaI in., A E Ibf-in.,
Opening, in. Max. Min. Max. Min. Max. in., Min. in., Min. Min.

2.125 0.801 0.940 1.490 1.635 0.209 0.344 3000


2.125 0.990 1.010 1.490 1.635 0.249 0.406 3700
2.125 1 .O03 1.187 1.490 1.635 0.281 0.469 4400
2.125 1.146 1.169 1.490 1.635 0.318 0.469 5100
2.125 1.141 1.260 1.250 1.640 0.356 0.531 6000

2.250 1.213 I .385 1.250 1.640 0.418 0.594 6800


2.250 1.285 1.635 1.275 1.640 0.479 0.594 7700
2.375 1.357 1.635 1.301 1.640 0.490 0.656 8700
2.375 1.429 1.635 1.326 1.715 0.490 0.656 9700
2.500 1.501 1.701 1.351 1.790 0.490 0.687 10,800

2.500 1.573 1.760 1.376 1 .E65 0.632 0.781 11,900


2.500 1.645 1.980 1.398 1.940 0.632 0.796 13,000
2.625 1.717 2.197 1.427 2.015 0.632 0.812 14,200
2.625 1.789 2.197 1.452 2.090 0.740 0.937 15,400
2.750 1.861 2.197 1.477 2.165 0.740 0.937 16,700

2.750 1.933 2.322 1.503 2.165 0.740 1 .o00 18,000


2.750 2.005 2.387 1.520 2.165 0.847 1.062 18,000
2.750 2.028 2.180 1.545 2.165 0.847 1 .O62 18,000
2.750 2.145 2.510 1.578 2.165 0.847 1.125 18,000
2.875 2.245 2.395 1.578 2.165 0.970 1.187 18,000

2.875 2.325 2.475 1.578 2.165 0.980 1.187 18,000


3.062 2.400 2.560 1.578 2.165 0.990 1.250 18,000
3.062 2.490 2.640 1.578 2.165 1 .O62 1.312 18,000
3.250 2.650 2.800 1.578 2.165 1 .O62 1.375 18.000
3.250 2.730 2.880 1.578 2.165 1.150 1.437 18,000

3.500 2.895 3.050 1.578 2.165 1.193 1.500 18,000


3.500 3.000 3.125 1.578 2.165 1.276 1.562 18,000
3.625 3.140 3.290 1.578 2.165 1.303 1.562 18,000

--``-`-`,,`,,`,`,,`---

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
SOCKET WRENCHES, EXTENSIONS, ADAPTORS,
ASME 8107.2-2002 AND UNIVERSAL JOINTS, POWER DRIVE (IMPACT) (INCH SERIES)

TABLE 7 TYPE I, CLASS 1 AND 2, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON
(12-POINT), REGULAR AND LONG LENGTH, 1 in. DRIVE
Outside Diameter, in.
Nut Bolt Clearance
Overall Length, in. Nut End, Drive End, Opening Hole Proof
C D Depth. Diameter, Torque,
Nominal Regular, Long, A E Ibf-in..
Opening, in. Max. Min. Min. Max. Min. Max. in., Min. in., Min. Min.

2.438 2.937 1.281 1.448 1.990 2.135 0.356 0.531 6400


2.500 2.937 1.365 1.510 1.990 2.135 0.41 8 0.594 7400
2.500 2.937 1.417 1.544 1.990 2.135 0.479 0.594 8400
2.563 2.937 1.480 1.607 1.990 2.135 0.490 0.656 9400
2.563 2.937 1.490 1.763 1.990 2.135 0.490 0.656 10,500
2.687 2.937 1.521 1.763 1.990 2.197 0.490 O.687 11,700
2.687 2.937 1.552 1.823 1.990 2.197 0.632 0.781 12,800
2.750 2.937 1.680 1.980 1.990 2.197 0.632 0.796 14,100
2.750 2.937 1.736 2.197 1.990 2.197 0.632 0.81 2 15,400
2.875 3.187 1.828 2.260 1.990 2.197 0.740 0.937 16,700
2.938 3.187 1.920 2.322 1.990 2.322 0.740 0.937 18,000
2.938 3.187 2.012 2.397 1.990 2.397 0.740 1.o00 19,500
3.000 3.437 2.104 2.473 1.990 2.473 0.847 1.O62 21,000
3.063 3.437 2.196 2.548 1.990 2.548 0.847 1.O62 22,000
3.063 3.437 2.288 2.623 1.990 2.623 0.847 1.125 24,000
3.250 3.437 2.379 2.699 1.990 2.699 0.970 1.187 26,000
3.250 3.437 2.471 2.774 1.990 2.774 0.980 1.187 27,000
3.250 3.437 2.563 2.849 2.240 2.849 0.990 1.250 28,000
3.250 3.437 2.655 2.925 2.240 2.925 1.O62 1.312 28,000
3.375 3.625 2.747 3.000 2.240 3.000 1.O62 1.375 28,000
3.438 3.687 2.839 3.073 2.240 3.073 1.O62 1.375 28,000
3.600 3.687 2.931 3.073 2.240 3.073 1.169 1.437 28,000
3.563 3.937 3.023 3.166 2.240 3.166 1.169 1.500 28,000
3.563 3.937 3.115 3.260 2.365 3.260 1.193 1.500 28,000
3.625 3.937 3.240 3.385 2.365 3.385 1.276 1.562 28,000
3.688 4.000 3.302 3.447 2.365 3.447 1.276 1.562 28,000
3.760 4.062 3.365 3.510 2.365 3.510 1.303 1.562 28,000
3.875 4.325 3.490 3.640 2.365 3.640 1.353 1.687 28,000
3.937 4.325 3.490 3.640 2.365 3.640 1.353 1.750 28,000
4.000 4.325 3.61 5 3.760 2.365 3.760 1.380 1.750 28,000
4.000 4.625 3.61 5 3.760 2.365 3.760 1.460 1.812 28,000
4.125 4.625 3.677 3.885 2.365 3.885 1.460 1.875 28,000
4.250 4.625 3.740 4.010 2.365 4.010 1.490 1.875 28,000
4.375 4.81 2 3.990 4.100 2.365 4.1O0 1.567 1.937 28,000
4.500 4.81 2 3.990 4.072 2.365 4.072 1.567 1.937 28,000
4.625 4.81 2 3.990 4.135 2.365 4.135 1.600 1.937 28,000
4.625 5.062 4.115 4.260 2.365 4.260 1.675 2.125 28,000
4.750 5.062 4.115 4.385 2.365 4.385 1.708 2.125 28,000
4.750 5.250 4.180 4.572 2.365 4.572 1.708 2.312 28,000
4.750 5.437 4.240 4.760 2.365 4.760 1.870 2.375 28,000
5.375 5.437 4.740 5.040 2.365 5.040 1.911 2.375 28,000
5.375 5.437 4.750 5.050 2.365 5.050 2.000 2.560 28,000
5.375 5.437 4.900 5.365 2.365 5.365 2.150 2.625 28,000
5.750 6.000 5.120 5.520 2.365 5.520 2.200 2.850 28,000
5.750 6.000 5.300 5.680 2.365 5.680 2.250 2.850 28,000
5.750 6.000 5.400 5.835 2.365 5.835 2.300 2.850 28,000
6.000 6.000 5.600 6.150 2.365 6.150 2.400 3.090 28,000

10
--``-`-`,,`,,`,`,,`---

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
SOCKET WRENCHES, EXTENSIONS, ADAPTORS,
AND UNIVERSAL JOINTS, POWER DRIVE (IMPACT) (INCH SERIES) ASME 8107.2-2002

TABLE 8 TYPE VII, CLASS 1 AND 2, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON
(12-POINT), REGULAR AND LONG LENGTH, #5 SPLINE DRIVE
Outside Diameter, in.
Nut Bolt Clearance
Overall Length, in. Nut End, Drive End, Opening Hole Proof
C D Depth, Diameter, Torque,
Nominal Regular, Long, A E Ibf-in.,
Opening, in. Max. Min. Min. Max. Min. Max. in., Min. in., Min. Min.

2.438 2.937 1.281 1.448 2.365 2.406 0.356 0.531 6400


2.500 2.937 1.365 1.510 2.365 2.406 0.418 0.594 7400
2.500 2.937 1.417 1.544 2.365 2.406 0.479 0.594 8400
2.563 2.937 1.480 1.607 2.365 2.406 0.490 0.656 9400
2.563 2.937 1.490 1.763 2.365 2.406 0.490 0.656 10,500

2.687 2.937 1.521 1.763 2.365 2.406 0.490 O. 687 11,700


2.687 2.937 1.552 1.823 2.365 2.406 0.632 0.781 12,800
2.750 2.937 1.736 2.197 2.365 2.406 0.632 0.812 15,400
2.875 3.187 1.828 2.380 2.365 2.406 0.740 0.937 16,700
2.938 3.187 1.920 2.380 2.365 2.406 0.740 0.937 18,000

2.938 3.187 2.012 2.397 2.365 2.406 0.740 1.o00 19,500


3.000 3.437 2.104 2.473 2.365 2.473 0.847 1.O62 21,000
3.063 3.437 2.288 2.623 2.365 2.510 0.847 1.125 24,000
3.250 3.437 2.379 2.699 2.365 2.635 0.970 1.187 26,000
3.250 3.437 2.563 2.849 2.365 2.822 0.990 1.250 29,000

3.250 3.437 2.655 2.925 2.365 2.822 1.O62 1.312 31,000


3.438 3.687 2.839 3.073 2.365 3.073 1.O62 1.375 34,000

--``-`-`,,`,,`,`,,`---
3.500 3.687 2.931 3.073 2.365 3.073 1.169 1.437 36,000
3.563 3.937 3.115 3.260 2.365 3.260 1.193 1.500 40,000
3.625 3.937 3.240 3.385 2.365 3.260 1.276 1.562 42,000

3.750 4.062 3.365 3.510 2.365 3.385 1.303 1.562 46,000


3.875 4.325 3.490 3.510 2.365 3.510 1.353 1.687 48,000
3.937 4.325 3.490 3.510 2.365 3.51 O 1.353 1.750 48,000
4.000 4.325 3.61 5 3.760 2.365 3.635 1.380 1.750 48,000
4.000 4.625 3.615 3.760 2.365 3.760 1.460 1.812 48,000

4.250 4.625 3.740 4.010 2.365 4.010 1.490 1.875 48,000


4.375 4.81 2 3.990 4.010 2.365 4.135 1.567 1.937 48,000
4.625 4.81 2 3.990 4.135 2.365 4.135 1.600 1.937 48,000
4.625 5.062 4.115 4.260 2.365 4.260 1.675 2.125 48,000
4.750 5.062 4.115 4.385 2.365 4.260 1.708 2.125 48,000

4.750 5.437 4.240 4.760 2.365 4.635 1.870 2.375 48,000


5.375 5.437 4.740 4.760 2.365 4.760 1.911 2.375 48,000

11

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
SOCKET WRENCHES, EXTENSIONS, ADAPTORS,
ASME 8107.2-2002 AND UNIVERSAL JOINTS, POWER DRIVE (IMPACT) (INCH SERIES)
--``-`-`,,`,,`,`,,`---

TABLE 9 TYPE I, CLASS 1 AND 2, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON
(12-POINT), REGULAR AND LONG LENGTH, I’/-in. DRIVE
Outside Diameter, in.
Nut
Overall Length, in. Nut End, Drive End, Opening Bolt Clearance
Nominal C D Depth. Hole Diameter,
Opening, Regular, Long, A E
in. Max. Min. Min. Max. Min. Max. in., Min. in.. Min.

3.250 4.000 2.490 2.885 2.990 3.260 0.750 0.937


3.250 4.000 2.490 2.885 2.990 3.260 0.875 1 .o00
3.250 4.000 2.553 2.915 2.990 3.260 0.931 1 .O62
3.250 4.000 2.553 2.915 2.990 3.260 1 .o00 1 .O93
3.250 4.000 2.615 3.041 2.990 3.260 1 .O63 1.125

3.250 4.000 2.740 3.041 2.990 3.260 1 .O63 1.187


3.375 4.250 2.740 3.135 2.990 3.260 1.109 1.187
3.375 4.250 2.865 3.135 2.990 3.260 1.140 1.250
3.656 4.375 2.921 3.198 2.990 3.260 1.181 1.312
3.656 4.375 2.990 3.260 2.990 3.260 1.218 1.312

3.812 4.500 3.178 3.573 3.240 3.573 1.250 1.375


3.812 4.500 3.183 3.635 3.240 3.635 1.296 1.437
3.938 4.750 3.183 3.635 3.240 3.635 1.343 1.469
3.938 4.750 3.240 3.698 3.240 3.698 1.375 1.500
4.125 5.000 3.365 3.822 3.240 3.822 1.406 1.562

4.125 5.000 3.365 3.822 3.240 3.822 1.456 1.562


4.188 5.000 3.490 3.885 3.240 3.885 1.500 1.562
4.188 5.000 3.615 3.941 3.240 3.941 1.551 1.687
4.188 5.000 3.678 4.073 3.240 4.073 1.578 1.750
4.188 5.000 3.740 4.103 3.240 4.103 1.609 1.750

4.312 5.125 3.865 4.198 3.240 4.198 1.656 1.812


4.312 5.125 3.925 4.260 3.240 4.260 1.688 1 .a44
4.500 5.250 4.053 4.385 3.240 4.385 1.750 1 .a75
4.500 5.250 4.115 4.573 3.240 4.573 1.781 1.937
4.625 5.375 4.178 4.635 3.240 4.635 1.812 1.937

4.625 5.375 4.178 4.698 3.240 4.698 1.843 1.937


4.800 5.625 4.365 4.835 3.240 4.835 1.890 2.125
4.800 5.625 4.490 4.885 3.240 4.885 1.931 2.125
4.800 5.625 4.553 4.941 3.240 4.941 2.000 2.125
4.800 5.625 4.615 5.010 3.240 5.01 O 2.000 2.187

5.063 5.750 4.678 5.073 3.240 5.073 2.045 2.249


5.063 5.750 4.740 5.135 3.240 5.135 2.093 2.31 1
5.063 5.750 4.865 5.135 3.240 5.135 2.125 2.375
5.063 5.750 4.865 5.198 3.240 5.198 2.156 2.375
5.188 5.875 4.865 5.260 3.240 5.260 2.250 2.375

5.188 5.875 4.920 5.322 3.240 5.322 2.250 2.387


5.312 6.125 4.990 5.385 3.240 5.385 2.281 2.399
5.312 6.125 4.990 5.448 3.240 5.448 2.328 2.405
5.625 6.500 5.115 5.573 3.240 5.573 2.375 2.41 1
5.625 6.500 5.240 5.635 3.240 5.635 2.406 2.423

5.750 6.750 5.302 5.698 3.240 5.698 2.500 2.435


5.875 6.875 5.490 5.822 3.240 5.822 2.500 2.447
5.875 6.875 5.490 5.885 3.240 5.885 2.500 2.459
5.875 6.875 5.553 5.941 3.240 5.941 2.593 2.471

12

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
SOCKET WRENCHES, EXTENSIONS, ADAPTORS,
AND UNIVERSAL JOINTS, POWER DRIVE (IMPACT) (INCH SERIES) ASME 6107.2-2002

TABLE 9 TYPE I, CLASS 1 AND 2, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON
(12-POINT), REGULAR AND LONG LENGTH, I'/*in. DRIVE (CONT'D)
Outside Diameter, in.

Overall Length, in. Nut End, Drive End, Nut Bolt Clearance
Nominal C D Opening Hole Diameter,
Opening, Regular, Long, Depth, A E
in. Max. Min. Min. Max. Min. Max. in., Min. in., Min.

6.063 7.000 5.740 6.073 3.240 6.073 2.593 2.483

6.063 7.000 5.740 6.103 3.240 6.103 2.625 2.495


6.063 7.000 5.802 6.135 3.240 6.135 2.750 2.507
6.375 7.375 5.865 6.322 3.240 6.322 2.750 2.519
6.375 7.375 5.921 6.322 3.240 6.322 2.750 2.531
6.375 7.375 5.990 6.395 3.240 6.395 2.796 2.543
6.625 7.625 6.115 6.573 3.240 6.573 2.835 2.555
6.625 7.625 6.302 6.573 3.240 6.573 3.000 2.567
6.625 7.625 6.365 6.635 3.240 6.635 3.000 2.580

TABLE 10 TYPE 1, CLASS 1, SINGLE HEXAGON (6-POINT), REGULAR LENGTH, 2% in. DRIVE
Outside Diameter, in.
Overall Nut Bolt Clearance
Length, Nut End, Drive End, Opening Hole
in., c D Depth, Diameter,
Regular, A E
Max. Max. Max. in., Min. in., Min.

5.500 4.313 5.500 1.276 1.562


5.500 4.313 5.500 1.303 1.562
5.500 4.313 5.500 1.353 I .e87
5.500 4.313 5.500 I 380 1.750
5.500 4.313 5.500 1.460 1.812

5.750 5.000 5.500 1.490 I .a75


5.750 5.000 5.750 1.567 1.937
5.750 5.000 5.750 1.600 1.937
5.750 5.000 5.750 1.675 2.125
5.750 5.000 5.750 1.708 2.125

--``-`-`,,`,,`,`,,`---
5.750 5.500 5.750 1.870 2.375
5.750 5.500 5.750 1.91 1 2.375
6.250 6.250 6.000 1.913 2.375
6.250 6.250 6.000 2.125 2.625
6.250 6.250 6.000 2.125 2.625

6.750 7.000 6.000 2.338 2.875


7.000 7.000 6.000 2.338 2.875
7.000 7.000 6.000 2.550 3.125
7.500 7.500 6.000 2.763 3.375
7.750 8.625 6.000 3.188 3.875

6?g 8.000 9.000 6.000 3.400 4.125

13

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
SOCKET WRENCHES, EXTENSIONS, ADAPTORS,
ASME B107.2-2002 AND UNIVERSAL JOINTS, POWER DRIVE (IMPACT) (INCH SERIES)

TABLE 11 TYPE II, CLASS 1 AND 2, SINGLE SQUARE (4-POINT) AND DOUBLE SQUARE
(&POINT), REGULAR AND LONG LENGTH SOCKETS, 3/8 in. DRIVE
Overall Length, in. Outside Diameter, in.
Nut Bolt Clearance
8 Point 4 Point Nut End, Drive End, Opening Hole Proof
C D Depth. Diameter, Torque,
Nominal Regular, Long, Regular, A E Ibf-in.,
Opening, in. Max. Min. Max. Min. Max. Min. Max. in., Min. in., Min. Min.

Y4 1.000 1.437 1.000 0.466 0.491 0.677 0.697 0.087 0.156 270
5
4 6 1.000 1.437 1.000 0.559 0.666 0.677 0.760 0.102 0.171 440
;I8 1.000 1.437 1.000 0.637 0.760 0.677 0.760 0.117 0.281 660
4 6 1.063 1.437 ... 0.740 0.854 0.740 0.854 0.203 0.281 930

lh 1.063 1.562 ... 0.865 0.948 0.865 0.948 0.209 0.343 1240
4' 6 1.140 1.562 ... 0.950 1.041 0.950 1.041 0.249 0.406 1600
:+ 4 6
1.290
1.290
...
...
...
...
1.052
1.115
1.138
1.198
1.052
1.115
1.138
1.198
0.281
0.318
0.469
0.469
2000
2200

TABLE 12 TYPE II, CLASS 1 AND 2, SINGLE SQUARE (4-POINT) AND DOUBLE SQUARE (&POINT),
REGULAR AND LONG LENGTH, '/2 in. DRIVE
Overall Length, in. Outside Diameter, in.
Nut Bolt Clearance
8-Point 4-Point Nut End, Drive End, Opening Hole Proof
C D Depth. Diameter, Torque,
Nominal Regular, Long, Long, A E Ibf-in.,

--``-`-`,,`,,`,`,,`---
Opening, in. Max. Min. Min. Min. Max. Min. Max. in., Min. in., Min. Min.

78 1.800 3.187 3.187 0.697 0.760 0.865 1.010 0.117 0.281 1100
4' 6 1.800 3.187 3.187 0.802 0.860 0.927 1.010 0.203 0.281 1500
'I* 1.800 3.187 3.187 0.898 0.978 0.927 1.041 0.209 0.344 2000
9
46 1.800 3.187 3.187 0.990 1.041 0.990 1.138 0.249 0.406 2600
78 1.800 3.187 ... 1.099 1.166 1.104 1.197 0.281 0.469 3300
11
116 1.800 3.187 ... 1.178 1.260 1.178 1.260 0.318 0.469 41O0
3
14 1.800 3.187 ... 1.302 1.343 1.115 1.385 0.356 0.531 5000
1346 1.800 3.187 ... 1.365 1.447 1.115 1.447 0.418 0.594 5000
'18 1.800 3.187 ... 1.490 1.573 1.245 1.572 0.479 0.594 5000
'716 2.100 3.437 ... 1.601 1.666 1.302 1.697 0.490 0.656 5000

1 2.100 3.437 ... 1.678 1.760 1.302 1.760 0.490 0.656 5000
1%6 2.100 ... ... 1.823 1.843 1.823 1.843 0.490 0.687 5000

14

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
SOCKET WRENCHES, EXTENSIONS, ADAPTORS,
AND UNIVERSAL JOINTS, POWER DRIVE (IMPACT) (INCH SERIES) ASME 8107.2-2002

TABLE 13 TYPE II, CLASS 1 AND 2, SINGLE SQUARE (4-POINT) AND DOUBLE SQUARE (&POINT),
REGULAR AND LONG LENGTH, in. DRIVE
Overall Length, in. Outside Diameter, in.
Nut Bolt Clearance
8-Point 4-Point Nut End, Drive End, Opening Hole Proof
C D Depth, Diameter, loque,
Nominal Regular, Long, Regular, Long, A E Ibf-in.,
Opening, in. Max. Min. Max. Min. Min. Max. Min. Max. in., Min. in., Min. Min.

lh 2.250 2.937 2.250 2.937 0.990 1.073 1.490 1.635 0.209 0.344 2000
94 6 2.250 2.937 2.250 2.937 1.146 1.166 1.490 1.635 0.249 0.406 2600
"6 2.250 2.937 2.250 2.937 1.240 1.260 1.490 1.635 0.281 0.469 3300
"116 2.250 2.937 2.250 2.937 1.333 1.354 1.490 1.635 0.318 0.469 41O0
Y* 2.313 2.937 2.313 2.937 1.490 1.635 1.490 1.635 0.356 0.531 5000

13/16 2.438 2.937 2.438 2.937 1.615 1.698 1.615 1.760 0.418 0.594 5000
'16 2.438 2.937 .. . .. . 1.740 1.760 1.615 1.826 0.479 0.594 5000
15
/16 2.438 2.937 ... .. . 1.802 1.826 1.615 1.826 0.490 0.656 5000
1 2.594 2.937 ... .. . 1.927 2.135 1.615 2.135 0.490 0.656 5000
1'11 6 2.594 2.937 ... ., . 1.990 2.135 1.740 2.135 0.490 0.687 5000

11 4 2.750 2.937 .. . .. . 2.115 2.322 1.740 2.322 0.632 0.781 5000


1'LI 2.750 2.937 .. . .. . 2.365 2.447 1.740 2.447 0.632 0.812 5000
15/16 2.750 2.937 .. . ... 2.490 2.697 1.740 2.697 0.740 0.937 5000
171s 2.750 .. . ... ... 2.615 2.697 1.740 2.697 0.740 1.o00 5000
15; 2.750 ... ... .. . 2.740 2.823 1.740 2.823 0.847 1.O62 5000

TABLE 14 TYPE 111, CLASS 1 AND 2, UNIVERSAL, SINGLE HEXAGON (6-POINT) AND DOUBLE
HEXAGON (12-POINT), REGULAR AND LONG LENGTH, /'* in. DRIVE
~~

Outside Diameter, in. Bolt


Nut Clearance
Overall Length, in. Nut End, ~~i~~
End, Opening Hole Depth Of 6Ok Proof
~

C D Depth, Diameter, Clearance Torque,


Nominal Regular, Long, -- A E Hole, Ibf-in.,
Opening, in. Max. Min. Min. Max. Min. Max. in., Min. in., Min. in., Min. Min.

98 2.500 2.750 0.520 0.760 0.677 0.910 0.117 0.281 0.937 450
7/16 2.500 2.750 0.607 0.760 0.677 0.910 0.203 0.281 0.937 625
5; 2.500 2.750 0.677 0.823 0.677 0.910 0.209 0.344 0.937 725
9
/16 2.500 2.750 0.740 0.850 0.677 0.910 0.249 0.406 0.937 750
516 2.500 2.750 0.855 0.948 0.730 0.910 0.281 0.469 0.937 750

'i46 2.650 3.250 0.970 1.010 0.730 0.910 0.318 0.469 0.937 750
14 2.650 3.250 1.030 1.135 0.730 0.910 0.356 0.531 0.937 750

15
--``-`-`,,`,,`,`,,`---

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
SOCKET WRENCHES, EXTENSIONS, ADAPTORS,
ASME B107.2-2002 AND UNIVERSAL JOINTS, POWER DRIVE (IMPACT) (INCH SERIES)

TABLE 15 TYPE 111, CLASS 1 AND 2, UNIVERSAL, SINGLE HEXAGON (6-POINT) AND DOUBLE
HEXAGON (12-POINT), REGULAR AND LONG LENGTH, in. DRIVE
Bolt
Outside Diameter, in.
Nut Clearance
Overall Length, in. Nut End, Drive End, Opening Hole Depth of Bolt Proof
C D Depth, Diameter, Clearance Torque,
Nominal Regular, Long. A E Hole, Ibf-in.,
Opening, in. Max. Min. Min. Max. Min. Max. in., Min. in., Min. in., Min. Min.

'4 6 3.000 3.500 0.600 0.814 0.865 1.063 0.203 0.281 1.250 850
'12 3.000 3.500 0.681 0.891 0.865 1.063 0.209 0.344 1.250 1 O00
9
46 3.000 3.500 0.763 0.968 0.865 1.063 0.249 0.406 1.250 1350
78 3.000 3.500 0.844 1.046 0.865 1.063 0.281 0.469 1.250 1500
'%6 3.000 3.500 0.926 1.123 0.927 1.250 0.318 0.469 1.250 1750

3.000 3.500 1.001 1.260 0.927 1.250 0.356 0.531 1.250 1750
3 116 3.000 3.500 1.009 1.278 0.927 1.250 0.418 0.594 1.250 1750
'18 3.000 3.500 1.178 1.355 0.927 1.250 0.479 0.594 1.250 1750

--``-`-`,,`,,`,`,,`---
15
116 3.250 3.750 1.252 1.433 0.927 1.250 0.490 0.656 1.250 1750
1 3.250 3.750 1.333 1.510 0.927 1.250 0.490 0.656 1.250 1750

'11 6 3.500 3.750 1.364 1.515 0.927 1.250 0.490 0.687 1.250 1750
1 '/a 3.500 3.750 1.439 1.590 0.927 1.250 0.632 0.781 1.250 1750
73/16 3.500 3.750 1.514 1.665 0.927 1.250 0.632 0.796 1.250 1750
1 '/4 3.500 3.750 1.588 1.740 0.927 1.250 0.632 0.812 1.250 1750
1546 3.500 3.750 1.663 1.815 0.927 1.250 0.748 0.906 1.250 1750

TABLE 16 TYPE IV, BAR, EXTENSION TABLE 17 TYPE V, ADAPTORS


Proof External Drive Internal Drive Overall Outside
Drive Nominal Shank Overall Length, in. Torque. Size, in., Size, in., Length, in., Diameter,
Size, Length, Diameter, Ibf-in., Nominal Nominal Max. in., Max.
~

in. in. in., Max. Min. Max. Min. 3


'12 18 1.563 I .O63
3
'14 2 0.380 1.750 2.500 500 18 '12 1.625 1.188
4 0.380 3.750 4.500 500 78 lh 1.813 1.375
6 0.380 5.750 6.500 500 ?* 1.906 1.375
5
"/a "/4 18 2.031 1.563
3 0.510 2.500 3.500 1200 3
6 0.510 5.500 6.500 1200 78 14 2.270 1.688
3
12 0.510 11.500 12.500 1200 1 14 2.688 2.063
3
'12 14 1 3.060 2.250
3 0.700 2.500 3.500 3500
5 0.700 4.500 6.000 3500
6 0.700 5.500 6.500 3500
10 0.700 9.500 10.500 3500 TABLE 18 TYPE VI, UNIVERSAL JOINT
"/4
3 1.313 2.500 3.500 9000 External and Internal Overall
7 1.313 6.500 7.500 9000 Drive End Size, in., Length, in., Diameter,
10 1.313 9.500 10.500 9000 Nominal Max. in., Max.
13 1.313 12.500 13.500 9000
1 1.688 0.625
3 I .563 2.500 3.500 15,000 2.500 1 .o00
7 1.563 5.500 7.500 15,000 3.063 1.375
13 1.563 11.500 13.500 15,000 3.500 1.500
4.250 1.750
6.100 2.375

16

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
SOCKET WRENCHES, EXTENSIONS, ADAPTORS,
AND UNIVERSAL JOINTS, POWER DRIVE (IMPACT) (INCH SERIES) ASME B107.2-2002

TABLE 19 HEXAGON MANDREL DIMENSIONS AND MAXIMUM DEPTH OF MANDREL INSERTION


Hexagonal Mandrel Dimensions, in.
Size
Across Across Flats Tolerances Across
Flats, Comers, Maximum Depth of
in. Min. Mandrel Insert, in.

0.001 0.002 0.1745 0.069


0.001 0.002 0.2095 0.083
0.001 0.002 0.2440 0.096
0,001 0.002 0.2780 0.110
0.001 0.002 0.3133 0.133

0.001 0.002 0.3495 0.141


0.001 0.002 0.3880 O. 156
0.001 0.002 0.4225 0.156
0.001 0.002 0.4935 0.198
0.001 0.002 0.5635 0.239

9
46 0.001 0.003 0.6339 0.265
"8 0.001 0.003 0.7055 0.291
11
116 0.001 0.003 0.7769 0.317
74 0.001 0.003 0.8485 0.344
4' 6 0.001 0.003 0.9201 0.370

0.001 0.003 0.9917 0.396


0.001 0.003 1.0631 0.422
0.001 0.003 1.1297 0.479
0.001 0.003 1.2013 0.505
0.001 0.003 1.2728 0.531

0.001 0.003 1.3443 0.557


0.001 0.003 1.4160 0.583
0.001 0.003 1.4870 0.609
0.001 0.003 1.5590 0.635
0.001 0.003 1.6310 0.661

0.001 0.003 1.7020 0.687


0.001 0.007 1.7700 0.713
0.001 0.007 1.8410 0.739
0.001 0.007 1.9120 0.765
0.001 0.007 1.9830 0.791

0.001 0.007 2.0540 0.817


0.001 0.007 2.1240 0.873
0.001 0.007 2.4080 1.010
0.001 0.007 2.4790 1.O36
0.001 0.007 2.5490 1.O63
--``-`-`,,`,,`,`,,`---

0.001 0.007 2.6210 1.O89


0.001 0.007 2.6910 1.115
0.001 0.007 2.7620 1.141
0.001 0.007 2.8330 1.167
0.001 0.007 2.9030 1.193
0.001 0.007 2.9740 1.219

0.001 0.007 3.1160 1.271


0.001 0.008 3.1870 1.297
0.001 0.008 3.3280 1.349
0.001 0.008 3.399 1.375
0.001 0.008 3.541 1.427

17
Copyright ASME International
Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
SOCKET WRENCHES, EXTENSIONS, ADAPTORS,
ASME 8107.2-2002 AND UNIVERSAL JOINTS, POWER DRIVE (IMPACT) (INCH SERIES)

TABLE 19 HEXAGON MANDREL DIMENSIONS AND MAXIMUM DEPTH


OF MANDREL INSERTION (CONT'D)
Hexagonal Mandrel Dimensions, in.
Sire
Across Across Flats Tolerances Across
Flats, Corners, Maximum Depth of
in. Min. Mandrel Insert, in.

0.001 0.008 3.682 1.479


0.001 0.008 3.824 1.531
0.001 0.008 3.966 1.583
0.001 0.008 4.249 1.688
0.001 0.008 4.391 1.740

4 0.001 0.010 4.532 1.855


4'/8 0.001 0.010 4.674 1.907
45/4 0.001 0.010 4.816 1.959
4% 0.001 0.010 5.099 2.063

TABLE 20 SQUARE MANDREL DIMENSIONS


Square Mandrel Dimensions, in.

--``-`-`,,`,,`,`,,`---
Size
Across Across Flats Tolerances Across
Flats, Corners, Maximum Depth of
in. (+I (-1 Min. Mandrel Insertion, in.

0.001 0.003 0.2570 0.093


0.001 0.003 0.3006 0.109
0.001 0.003 0.3436 0.125
0.001 0.003 0.4294 0.140
0.001 0.003 0.5153 0.156

0.001 0.003 0.6012 0.21 8


0.001 0.003 0.6870 0.265
0.001 0.003 0.7730 0.328
0.001 0.003 0.8690 0.375
0.001 0.003 0.9450 0.375

0.001 0.003 1.0310 0.437


0.001 0.003 1.1170 0.453
0.001 0.003 1.2020 0.500
0.001 0.003 1.2880 O.546
1 0.001 0.003 1.3740 O. 546

18

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
ASME Services
ASME is committed to developing and delivering technical information. At ASME’s Information Central, we make
every effort to answer your questions and expedite your orders. Our representatives are ready to assist you in the
following areas:

ASME Press Member Services & Benefits Public Information


Codes & Standards Other ASME Programs Self-study Courses
Credit Card Orders Payment Inquiries Shipping Information
IMechE Publications Professional Development Subscnptions/Joumals/Magazines
Meetings & Conferences Short Courses Symposia Volumes
Member Dues Status Publications Technical Papers

How can you reach us? It’s easier than ever!

There are four options for making inquiries* or placing orders. Simply mail, phone, fax, or E-mail us and an Information
Centrai representative will handle your request.

Mail Call Toll Free Fa-24 hours E-Mail-24 hours


ASME US & Canada: 800-THE-ASME 973-882-1717 Infocentral@asme.org
22 Law Drive, Box 2900 (800-843-2763) 973-882-5155
Fairfield, New Jersey Mexico: 95-800-THE-ASME
07007-2900 (95-800-843-2763)
Universal: 973-882-1167
--``-`-`,,`,,`,`,,`---

* Information Central staff are not permitted to answer inquiries about the technical content of this code or standard.
Information as to whether or not technical inquiries are issued to this code or standard is shown on the copyright
page. Ail technical inquiries must be submitted in writing to the staff secretary. Additional procedures for inquiries
may be listed within.

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
AMERICAN NATIONAL STANDARDS FOR HAND TOOLS
Socket Wrenches. Hand (Inch Series) ........................................................... B107.1-2002
Socket Wrenches. Extensions. Adaptors. and Universal Joints.
Power Drive (Impact) (Inch Series) .............................................................. 8107.2-2002
Socket Wrenches. Power Drive (Non-Impact) (Inch Series) ................................. B107.3-1978(R1991)
Driving a n d Spindle Ends for Portable Hand. Impact. Air. and
Electric Tools (Percussion Tools Excluded) .................................................... B107.4M-1995
Socket Wrenches. Hand (Metric Series) ....................................................... B107.5M-2002
Adjustable Wrenches ........................................................................ B107.8M-1996
Handles a n d Attachments for Hand Socket Wrenches - Inch and Metric Series ................ B107.10M-1996
Pliers: Diagonal Cutting a n d End Cutting ...................................................... .B107.1 1.2002
Nut Drivers (Spin Type. Screwdriver Grip) (Inch Series) ......................................... B107.12-1997
Pliers - Long Nose. Long Reach ............................................................ B107.13M-1996
Hand Torque Tools ......................................................................... B107.14M-1994
Flat Tip Screwdrivers ......................................................................... B107.15-2002
Shears (Metal Cutting. Hand) ................................................................ B107.16M-1998
Gages. Wrench Openings. Reference ......................................................... B107.17M-1997
Pliers (Wire Twister) ........................................................................ B107.18M-1996
Pliers. Retaining Ring .................................................................. B107.19-1993(R1998)
Pliers (Lineman's. I r o n Worker's. Gas. Glass. Fence. and Battery) .............................. B107.20M-1998
Wrench. Crowfoot Attachments ................................................................ B107.21-1998
Electronic Cutters ........................................................................... B107.22M-1998
Pliers. M u l t i p l e Position. Adjustable ......................................................... .B107.23 M.1997
Pliers - Performance Test Methods ......................................................... B107.25M-1996
Pliers. M u l t i p l e Position (Electrical Connector) .................................................. B107.27-1996
Electronic Torque Instruments ............................................................... B107.28M-1997
Electronic Tester. Hand Torque Tools ....................................................... .B107.29 M.1998
Cross Tip Screwdrivers ....................................................................... .B107.3 0.2002
Screwdrivers. Cross Tip Gaging ............................................................. B107.31M-1997
Socket Wrenches f o r Spark Plugs ............................................................ B107.34M-1997
Nut Drivers (Spin Type. Screwdriver Grip) (Metric Series) ..................................... B107.35M-1997
Electronic Pliers ............................................................................ B107.38M-1998
Nail Hammers -
Safety Requirements ....................................................... B107.41M-1997
Hatchets: Safety Requirements .............................................................. B107.42M-1997
Wood-Splitting Wedges: Safety Requirements ................................................ B107.43M-1997
Glaziers' Chisels and W o o d Chisels ........................................................... .B107.44 .2002
Ripping Chisels a n d FlooringlElectricians' Chisels .............................................. .B107.4 5.2002
Stud. Screw. a n d Pipe Extractors: Safety Requirements ....................................... B107.46M-1998
Metal Chisels: Safety Requirements .......................................................... B107.47M-1998
Metal Punches and Drift Pins: Safety Requirements ........................................... B107.48M-1998
Nail Sets: Safety Requirements .............................................................. B107.49M-1998
Brick Chisels a n d Brick Sets: Safety Requirements ............................................ B107.50M-1998
Star Drills: Safety Requirements ............................................................... B107.51-2001
Nail-Puller Bars: Safety Requirements ........................................................ B107.52M-1998
--``-`-`,,`,,`,`,,`---

Ball Peen Hammers: Safety Requirements ................................................... .B107.53 M.1998


Heavy Striking Tools: Safety Requirements ..................................................... B107.54-2001
Axes: Safety Requirements .................................................................. B107.55M-2002
Body Repair Hammers and D o l l y Blocks:Safety Requirements ................................... B107.56-1999
Bricklayers' Hammers and Prospecting Picks: Safety Requirements .............................. B I 07.57-2001
Riveting. Scaling. and Tinner's Setting Hammers: Safety Requirements ........................ B107.58M-1998
Slugging a n d Striking Wrenches .............................................................. .B107.5 9.2002
Wrenches .................................................................................. .B107.10 0.2002

The ASME Publications Catalog shows a complete list of all the Standards published by the Society. For a
complimentary catalog. or the latest information about our publications. call 7-800-THE-ASME (7.800.843.2763) .

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale
--``-`-`,,`,,`,`,,`---

Copyright ASME International


Provided by IHS under license with ASME
No reproduction or networking permitted without license from IHS Not for Resale

You might also like