Dynaflox Wireless IR Handheld Operator manual

Wireless IR Handheld Operator

Manual
REV 05/2015

1
 Dynaflox Wireless IR Handheld Operator manual

Content

Part1 Instruction ..................................................................... 错误！未定义书签。

1.1 Spefication ....................................................................................................... 3
1.2 Product Characteristics .................................................................................. 3
Part1 Operation ........................................................................................................ 4
2.1 Handheld Operator ......................................................................................... 4
2.2 Turn on/Turn off.............................................................................................. 4
2.3 Menu window ................................................................................................ 5
2.4 Dynaflox IrDA system..................................................................................... 6
2.4.1 IR meter reading system....................................................................... 6
2.4.2 Current data Inquiry ............................................................................ 6
2.4.3 History Data Inquiry ............................................................................ 8
2.4.4 Parameter setting .................................................................................. 9
2.4.5 Inquiry ................................................................................................. 13
2.4.6 Other parameters setting.................................................................... 15
Part3 Data processing ............................................................................................. 16
3.1 USB data transmission program ............................................................ 16
3.2 Upload and download instruction ............................................................... 18
Part3 Service and warranty ................................................................................... 19

2
 Dynaflox Wireless IR Handheld Operator manual

Part1 Instruction
1.1 Spefication

CPU SAMSUNG (ARM MCU)，132MHz

RAM 64MB, 512 SRAM

Temperature –20℃ - 60℃

Power supply 3 set of rechargeable AA battery

Size 200mm*79mm*59mm

Communication USB interface

1.2 Product Characteristics

1． Applied Infrared Communication，Active distance: 0.5m，Common distance:2-3m；
2． Read various of Current data and history data，data was stored in the operator with
excel format, it will not loss data in power failure situation. The excel sheet could be
read and modified by computer.
3． Data will be calibrated by CRC，to ensure good accuracy and stability.

3
 Dynaflox Wireless IR Handheld Operator manual

Part2 Operation
2.1 Keyboard

□ - 9□
0 Number key；

Power：Turn on or turn off

Back light：close or open the back light；

Function：Enter the main menu；

And : check previous and next menu；

Clean(C):delete data or get back to previous menu；

Enter

2.2 Turn on / turn off

Long press“power”button，wait for few seconds，the operator system will start and
enter system.
4.1V

Dynaflox

2014.06.05 12:00:00

4.1V Current battery voltage.

2014.06.05 12:00:00 Current time.

Three methods for turn off:

4
 Dynaflox Wireless IR Handheld Operator manual
1. Long press“power”button to turn off;
2. Long time without operation, the operator will turn off as default setting(in main menu
could set the time interval);
3. Low battery voltage.

2.3 Function menu

After enter start menu，press “menuF2” could enter function menu.

4.1V
Function menu
【1】 System communication
【2】 system information
【3】 system setup
【4】 system testing
【5】 operational procedure

【ESC】Quit

（1）system communication
Use USB cable to connect operator with PC, enter the menu, keep in communication
with the communication tools and operator.
（2）System information
Enter the menu and inspect the machine information、file info、system time and
battery status.
System time could not be modified in the menu, if requires modification,please use
communication tools;or enter IR meter reading system to change the time.
When the operator fully charged, the battery voltage is 4.2V. If battery voltage lower
than 3.8V, meter reading system could not get started, only could read the data in the
operator; If battery voltage lower than 3.3V, operator will turn off.

（3）System setting
In the menu, user could set LCD adjustment, FLASH Formatting，change password,
and shutdown time.Others are spare menu.

（4）System test
In the menu,user could make test for keypad, LCD and files. Others are spare menu.

5
 Dynaflox Wireless IR Handheld Operator manual

（5）Operating Procedure
Operate the IR meter reading system.In start menu, ，press any key（except menu
F2）could enter IR meter reading system.

2.4 Dynaflox IrDA system

2.4.1 IR meter reading system

Dynaflox IrDA System Dynaflox IrDA System

================= =================
Press[←] Enter In Enter 1.Current Data Query->
Press[F1] Exit 2.History Data Query->
Enter menu 3.Parameter Setting->
Saved Data will be 4.Parameter Query->
lost if Exit! 5.Resetting

Dynaflox IrDA system has five menus：

Current Data Query、History Data Query、Parameter Setting、Parameter Query and Resetting.

2.4.2 Current data Inquiry

Enter menu there is totally five options,
Press button 1 ~ 5 respectively corresponding operation can be performed, respectively.

Current Data Query

==================
1.Accumulative Flow
2.Instantaneous Flow
3.Battery Level
4.Current Time
5.Host NO.( tag NO.)

(1) Accumulative Flow

Dynaflox IrDA System

==================== Press[←] to read data again.
2014-06-05 10:24:30 Press[Esc] return to previous menu
S/N:12 press[5] to save data, saved data could be checked in
+:5.7800 m3 HistoryDataQuery->ViewSavedRecord->AccumulativeFlow..
-:87.0000 m3 After power off the data will not get lost, the data will be
press[5]to save data saved in the Handheld operator.
Press[←] Read Again If the tag6NO. is set, S/N will shows the tag NO.
Press[Esc]Go Bac
 Dynaflox Wireless IR Handheld Operator manual

(2) Instantaneous Flow

Dynaflox IrDA System

Press[←]to read data again.
====================
Press[Esc] return to previous menu
2014-06-05 10:24:30
press[5] to save data ， saved data could be checked in
S/N:12
HistoryDataQuery->ViewSavedRecord->InstantaneousFlow.
Instantaneous Flow:
After power off the data will get lost from.the Handheld
+ 1.340 m3/h
operator.
press[5]to save data
If the tag NO. is set, S/N will shows the tag NO.
Press[←] Read Again
Press[Esc]Go Back

(3) Battery Level

Dynaflox IrDA System

====================
Current battery voltage

3.600V

Press[←] Read Again

Press[Esc]Go Back

(4) Current Time (5) Host NO.(TAG NO.)

Dynaflox IrDA System Dynaflox IrDA System

=================== ====================
Current Time: Current S/N:
12
2014-06-05 10:30:08 Host NO.( tag NO.):
Left above 004

Press[←] Read Again Press[←] Read Again

Press[Esc]Go Back Press[Esc]Go Back

If tag NO.is not be set,it will shows “Not Set”.

7
 Dynaflox Wireless IR Handheld Operator manual

2.4.3 History Data Query

Press button 1 ~ 3 respectively corresponding operation can be performed, respectively.

History Data Query

=================

1.Record Data Quantity

2.Accumulative Flow
3.View Saved Record

(1) Record Data Quantity

Record Data Quantity

================
Month : 21
Day : 51
Hour : 125

Press[←] Read Again

Press[Esc]Go Back

The meter’s month-cumulative number,day-cumulative number and hour-cumulative number

is 21, 51 and 125.

(2) Accumulative Flow

Month Water Flow Day Water Flow

Accumulative Flow
================ ================
================
Reading... Reading...
1.Month Water Flow
2.Day Water Flow
Progress : 21/21 Progress : 17/51

Saved Success! Pause

Press[←] Read Again Press[←] Continue
Press[Esc] Go Back Press[Esc] Go Back

In the reading process, please align the infrared and press key[←] as it shows when
there is a pause.If you want to cancel the reading process, press key[Esc] to stop and go
back to previous page.
Reading Result is stored in .CSV and .TXT format in the handset, you can export the
handset opened with EXCEL, file names are the current S / N number .CSV and S / N
number .TXT. For example, the current meter 8
S / N number is 70000012, the copy read
cumulative months after a successful flow generated file called 70000012.CSV; and copy
successful reading day cumulative flow generated after file name 70000012.TXT.
 Dynaflox Wireless IR Handheld Operator manual

(3) View Saved Record

View Saved Record Dynaflox IrDA System Dynaflox IrDA System

================ ================== ==================
2014-06-05 10:24:30 2014-06-05 10:24:30
1.Accumulative Flow Adr: Left above 004 Adr: Left above 004
2.Instantaneous Flow +:5.7800 m3 Instantaneous Flow:
-:87.0000 m3 + 1.340 m3/h

Press[Up] or [Down] Press[Up] or [Down]

Press[Esc] Go Back Press[Esc] Go Back

The function is querying meter’s latest Accumulative or Instantaneous Flow record which has
been saved..
Note: The current cumulative flow can store up to 499 records, which store records stored in a
file format in Flow.CSV. The current instantaneous flow can store up to 99 table records,
content is stored in the handset memory (after exiting power down the system or the content is
missing). If a table's current instantaneous flow is repeatedly stored, the previous records
stored once covered by the new query to the latest in a record store.
Adr digit number indicates the current meter settings (ie tag NO.), Can support up to eight
characters or 16 numbers, letters show; If this table is not set bit number is displayed S / N:
xxxx.

2.4.4 Parameter Settings

Press button 1 ~ 7 respectively corresponding operation can be performed, respectively

Parameters Setting
===============
1.User Setting->
2.Factory Setting->
3.Pulse Setting->
4.Current Setting->
5.DAC Debugging->
6.Factory Reset
7.ACC Sample Set->

(1) User Setting

9
 Dynaflox Wireless IR Handheld Operator manual

1) MBUS Address: Meter’s 485/wireless communication

User Setting address;
================== 2) MBUS Band Rate: Meter’s 485/wireless communication
1.MBUS Address Band Rate; Its value can only be one of 1200,2400,4800 or
2.MBUS Baud Rate 9600,Other Band Rate Setting are not succeed.
3.Unit Configuration 3) Unit Configuration: Measuring unit, and it can be chosen as
4.Tag NO. Set m3/h, L/min or GAL/min;
4) Tag NO.: meter installation location information.It is
convenient for users to remember and query. It can be
set by users (or not) to differentiate different meters.

MBUS Address Setting MBUS Baud Rate Setting Display Units Configuration

Dynaflox IrDA System Dynaflox IrDA System Dynaflox IrDA System

================= ================== =================
MBUS Address MBUS Baud Rate: Unit Configuration:
2 2400
Enter New Address: Enter New Baud Rate: m3/h
(1-255) (1200 2400 4800 9600)
25 Set Success！ 9600 Set Success！ Press[0]or[1] Modify
Press[←] Set Again Press[←] Set Again 1:L/min 2:GAL/min
Press[Esc] Go Back Press[Esc] Go Back Press[Esc] Go Back

1) Correspondence between the memory bit resolution and S / N number

Tag NO. Set in SNaddr.CSV file, do more tables can store 499 bit number. Open
Dynaflox IrDA System this file, display D if it indicates when records before this record has
================== expired;
S/N:12 2) Set the bit number of support Pinyin, English letters and numbers,
Tag NO.: press the [←] key indicates that the input is completed. Supports up
Not set to eight characters or 16 bytes is set;
Enter New Tag NO.: 3) Press the [F1] key to switch input method, in the lower right corner of
Left above 004 the screen indicating the current input state, the default is digital
Set Success！ input;
Press[←] Set Again Status Tip: 123, digital; ABC uppercase; abc lowercase letters; PY,
Press[Esc] Go Back pinyin input.
4) using T9 Pinyin input association, such as input pinyin ming, press
the number keys 6464, which, [F2] key to select the current Chinese
characters, [←] key to finish input, '+' to select the alphabet, '-' to
select characters, on the turn, Press [Up] or [Down] key to choose
from multi-line characters.

10
 Dynaflox Wireless IR Handheld Operator manual
(2) Factory Setting

Factory Setting 1) Static Zero Setting: Water’s minor fluctuations will be seen as
================ zero to ensure measurement accuracy ;
1.Static Zero Setting 2) Password Setting: Water’s password (factory setting)
2.Password Setting changes, to prevent the operator operating ;
3.Correct Coefficient 3) Correct Coefficient: Test & Calibration(Not open to users);
4.Accumulation Set-> 4) Accumulation Set: Test & Calibration(Not open to users);
5.Synchronize Time 5) Synchronize Time: Set same time of hand-held operator and meter
6.Reverse Flow Enable 6) Reverse Flow Enable: Set in the direction of flow;
7.Low Flow Set 7) Low Flow Set: Test & Calibration(Not open to users);
8.Reverse Low Flow Set 8) Reverse Low Flow Set: Test & Calibration(Not open to users).

1. Static Zero Setting（Not open to users）

Dynaflox IrDA System Dynaflox IrDA System Dynaflox IrDA System

================ ================= =================
Temperature (oC): Temperature (oC):
Enter Password: 25 25
xxxx
Press[F1] Set Zero Static Zero, Success!
Press[Esc]Go Back Press[Esc]Go Back

If has been Set Static Zero Success, then choose the option again it will shows the screen below:
Press[1] Set Static Zero again.
Press[2] Recover the parameters before Setting, and it shows the
Static Zero Setting returning screen below:
================
Static Zero Recover Static Zero Recover
1.Static Zero Setting ================ =================
2.Static Zero Recover
Enter Password:
xxxx Recover Success!
Press[Esc]Go Back
2. Password Modify

Dynaflox IrDA System

=================
Enter Old Password:
xxxx Such settings require a password verification function
Enter New Password: within 5s after entering the password to be set to operate,
xxxx otherwise it is set to fail. The purpose is to reduce water
consumption, prevent operator misuse.
11
Password Set,Success! *Contact us to get the Initial Password.
Press[Esc] Go Back
 Dynaflox Wireless IR Handheld Operator manual

3. Correct Coefficient（Not open to users）

Dynaflox IrDA System
Dynaflox IrDA System =================
================ Coefficient:
2.7000
Enter Password: Enter New:
xxxx 1.2
Set Success!
Press[←] Set Again
Press[Esc] Go Back
4. Accumulation Set

Accumulation Set This feature can artificially change the sign of

================= the cumulative amount of water, in order to test,
1. calibrate use. This feature is not open to users.
Positive Cumulative Modify the same amount of positive and
flow modification negative cumulative operating under positive
cumulative amount of modifications Photos Case.
2.
Negative Cumulative
flow modification

Dynaflox IrDA System Dynaflox IrDA System Dynaflox IrDA System Dynaflox IrDA System
================ ================ ================ ================
Positive Flow(m3): Positive Flow(m3): Positive Flow(m3): Positive Flow(m3):
+25.0000 +25.0000 +25.0000 +10.00
Press[←] Modify Enter Password: +EnterCumulative:
xxxx 10.00 Positive Flow success！
Press[←] Set Again
Press[Esc] Go Back

5. Synchronize Time

Dynaflox IrDA System Dynaflox IrDA System Dynaflox IrDA System

================= ================= =================
Time Of Meter: Time Of Meter: Time Of Meter:
1970.01.01 04:59:24 1970.01.01 04:59:24
Press[←]
Time Of Hand-held: Time Of Hand-held: 2014.06.10 14:09:10
2014.06.10 14:09:10 2014.06.10 14:09:10
Press[5] Calibrate Enter Password: Synchronize,Success!
Press [←] Synchronize xxxx12 Press[←] Set Again
Press[Esc]Go Back Press[Esc] Go Back
 Dynaflox Wireless IR Handheld Operator manual

Press [5]

Dynaflox IrDA System Dynaflox IrDA System

================ ================
Time Of Hand-held:
2014.06.10 14:17:10
TimeSet:hh.mm.ss Calibrate Success
18.07.05 Press[←] Set Again
Date:yyyy.mm.dd Press[Esc] Go Back
2014.06.11

6. Reverse Flow Settings

Dynaflox IrDA System Dynaflox IrDA System

================= =================
Reverse Flow Enable: Reverse Flow Enable:

Closed Opened
Enter Password:
xxxx Set Success!
Press[←] Set Again
Press[Esc] Go Back

7. Low Flow Set

Dynaflox IrDA System Dynaflox IrDA System

================= =================
Low Flow mm/s
Enter Password: 1.090
xxxx Enter Low Flow:
0.55
Set Success! *LowFlowSet cut the
Press[←] Set Again positive and reverse
Press[Esc]Go Back flow at the same time

13
 Dynaflox Wireless IR Handheld Operator manual
8. Reverse Low Flow Set

Dynaflox IrDA System Dynaflox IrDA System

================= =================
Reverse Low Flow mm/s
Enter Password: 1.090
xxxx Enter Reverse Low:
0.55 *ReverseLowFlowSet
Set Success! cut the positive and
Press[←] Set Again reverse flow at the
Press[Esc]Go Back same time

(3) Pulse Setting

Pulse setting
================= 1) Pulse Enable: If be opened, it means pulse output is enable.
1.Pulse Enable 2) Unit Configuration: A pulse flow through each occurrence,
2. Unit Configuration unit L.

(4) Current Setting

Current setting
================== 1) 4-20mA Output Enable: If be opened, it means 4-20mA
1.4-20mA Output Enable output is enable.
2.4mA -Flow Rate 2) 4mA -Flow Rate: Output 4mA, the Instantaneous Flow;
3.20mA -Flow Rate 3) 20mA -Flow Rate: Output 4mA, the Instantaneous Flow;

(5) DAC Debugging

Please connect circuit as below :
DAC Debugging
=================
1.DAC Debugging
2.4mA-DAC Amount
3.20mA-DAC Amount
4.4-20mA Output Enable

According to step 1),2),3),4),5),6) in operation(4-20mA output of debugging and setting)

1) Set the value is 0m3/h in Parameter Setting->Current Setting->4mA-Flow Rate;

14
 Dynaflox Wireless IR Handheld Operator manual
2) Set the value is X in Parameter Setting->Current Setting->20mA-Flow Rate( Usually
the value of X is 10m3/h,and also can be set as user need);
3) Parameter Setting->DAC Debugging->DAC Debugging: Firstly,enter password .
Secondly, try to enter and record the value of DAC Amount and make sure the current
output is 4mA or 20mA as X1 and X2.
4) Parameter Setting->DAC Debugging->4mA-DAC Amount: Enter X1 here to set
success.If it is failed,please set again.
5) Parameter Setting->DAC Debugging->20mA-DAC Amount:Enter X2 here to set
success.If it is failed,please set again.
6) Parameter Setting->DAC Debugging->4-20mA Output Enable
(or Parameter Setting->Current Setting->4-20mA Output Enable ): Set it Opened.
Above steps, the output of debugging and setting is done,and output of 4-20mA
works now.(please operate according to the above steps, or maybe do not work)

(6) Factory Reset

Align the infrared,Press [6], if the screen below occur, means Factory Reset success.
Not open to users.

Dynaflox IrDA System

==================
Synchronize, Success!
Reverse Flow, Success!
Pulse, Success!
Low Flow Set, Success!
Accumulate, Success!
----------- Done -----------
Press[Esc] Go Back

(7) ACC sampling settings

Align the infrared,Press [6], if the password is right, the screen below occur:
Not open to users.

Dynaflox IrDA System 1) Read the parameter of UL_LOOPC_Val, and also can have a
================= modification.
1.UL_LOOPC_Val 2) Read the parameter of AG_STAGE2_A2_Val, and also can
2.AG_STAGE2_A2_Val have a modification.
3.AG_STAGE2_R2_Val 3) Read the parameter of AG_STAGE2_R2_Val, and also can
have a modification.
*Contact us to get the detailed parameter.
15
 Dynaflox Wireless IR Handheld Operator manual

2.4.5 Parameter Query

Parameters Query
=================
*Remarks:
1.Software Version
Except software version, pipe structure and
2.MBUS Query
current temperature Query, other parameters
3.Unit Configuration
can be got in Parameter Setting. It’s convenient
4.Pulse Query
for user’s integrated Query.
5.Current Query
Among them, the software version number
6.Pipe Structure Query
can’t be changed.
7.Temperature Query

the above functions refer to the instruction of the hand-held operator screen

Hereinafter, specify the item 6: The operation of Pipe Structure Query .

The premise of this operation is that there is pipe.txt file in the hand-held operator. If
there is no such file, align the infrared, press key [6], it will display *No pipe.txt Exist*. This
operation cannot be done now. The writing format 1 in pipe.txt file is as below:

Format specification:
Pipe type name + “:” + “0,0;” + “data1,data2;” + “data3,data4;” + Enter[←] key, and
all punctuations in it are English punctuations, or it will not recognize this pipe.
Possible results of this operation:
1) If there is such pipe configuration data in pipe.txt file,it will display the corresponding
pipe configuration, as shown in the screen below:

Dynaflox IrDA System

=================
Pipe Structure:

Dual path DN80

Press[←] Read Again

Press[Esc]Go Back

16
 Dynaflox Wireless IR Handheld Operator manual
2) If there is no such pipe configuration data in pipe.txt file, as shown in the screen below:

If press key [F1] now, you can add the corresponding Dynaflox IrDA system
pipe, enter the name of the pipe as format 1, then the ==================
data1, data2
pipe is automatically stored in the pipe.txt file and can be
data3, data4
queried in the future. Furthermore, the new pipe *Same Pipe Not Exist*
configuration data can also be directly modified in the Press [F1] Save Pipe
pipe.txt file. Wherein, data1, data2, data3 and data4 are Press[<-] Read Again
Press[Esc] Go Back
the parameters of the pipe configuration.

3) If there is no piper.txt file, the display is as shown in the screen below:

Dynaflox IrDA system The piper.txt file need to be added to

=================
the hand-held operator to query the pipe
* No pipe.txt Exist*
configuration. The addition method refers

Press[<-] Read Again to 3.2 the specification of uploading and

Press[Esc] Go Back downloading files.

2.4.6 Other interface specification

1. If there is no corresponding prompt in the interface, press [Esc] go back to the previous
menu.

2. If there is '->' symbol after the menu option indicates that there are menu selection after,
Without this flag should be aligned at this time meter infrared devices, select the
corresponding infrared copy after reading data.

3. In the key input string in the process, if a mistake you can press [Esc] to delete the
previous entry press the key [←] indicates that the input is completed; if no input directly
press the key [←]or[Esc] to no action direct return to the previous menu.

4. If you press the key [F1] to exit the system, the contents have been saved in History
Data Query -> View Saved Record -> Instantaneous Flow are emptied. After re-entering
the system, there is no contents in History Data Query-> View Saved Record -> Current
Instantaneous and need records stored in order to re-query.

17
 Dynaflox Wireless IR Handheld Operator manual

Chapter3 Data Processing

3.1 USB Data transfer program

1. Use USB cable to connect the handset to a PC, handheld into the "system
communication" on the menu, that handset displays "USB communication”。

2. Open communication tools，Double-click ，run operator

communication tools。

3. In the Operator communication tool，click ，Automatically select the

correct COM port, and then click on the "Connect POS machine" connections. Once
connected, the software most lower-left corner displays the connection status, such

as“ ”。

18
 Dynaflox Wireless IR Handheld Operator manual
4. Once connected, the software appears to the right handset file. As shown below:

t1.bin: to Dynaflox infrared meter reading system;

SNaddr.CSV: Number and S / N (number) of correspondence between the files. After
opening the file, if when records show D said before this bit number is set to have expired.
Additionally, this file can be modified to add the appropriate format based on human, after
editing the import handset can be used directly;
20140605.CSV: Indicates the current totalizer log files June 5, 2014 store. The
current cumulative flow records can be stored queries (handset date must be the same
with the meter date, otherwise errors may occur) at today's date .CSV file. After opening
the file, if the record before the show when D is a description of this record is not the latest
data, more than the latest record store updates;
70000012.CSV: meter S / N (number) of 70,000,012 monthly cumulative record store
files. Historical cumulative flow meter per month stored in S / N number .CSV file;
70000012.TXT: meter S / N (number) of 70,000,012 daily cumulative record store
files. Each day cumulative flow meter history stored in S / N number .TXT
file.

可点击 将文件下载至 PC 中，或点击 下载文件至手

19
 Dynaflox Wireless IR Handheld Operator manual
持机中。

3.2 上传和下载文件说明 Upload

1

3
(3)

(4)
5

and Download Files

手持机通讯工：Handheld communication tool

连接 POS 机：Connect to POS, 退出通讯：Exit
文件管理：File management, 机器设置 Setting, 生产下载：Download
文件类型：File type，开机画面：startup picture
文件总数：Total number of files
上传成功后删除文件：Delete the files after being successfully uploaded
下传时先删除相同文件名：Delete the same file name before download
文件名：File name, 大小：Size，日期：Date
下载到 POS 机：Download to POS,
下传并改文件名：Download and change the file name,
POS 新文件名：POS new file name, 上传到 PC 机：Upload to PC
上传并改文件名：Upload and change the file name
PC 新文件名：PC new file name
手持机连接在 COM4：Connect handheld to COM4

20
 Dynaflox Wireless IR Handheld Operator manual
[1] 上传手持机里文件到 PC 机
1.点击 连接到 POS 机(若链接成功左下角处显示手持机链接在 COM x)
2.点击 文件管理
3.选择 数据文件 存储位置所在
4.选择 要导出的文件
5.点击 上传到 PC 机 按钮(存储位置的文件架中不能有重名文件，否则上传不成功)

[2] 下载 PC 机里文件到手持机

(1) 点击 连接到 POS 机(若链接成功左下角处显示手持机链接在 COM x)

(2) 点击 文件管理
(3) 选择 要下载到手持机的数据文件
(4) 点击 下载到 POS 机 按钮

1. Upload the files from handheld to PC

(1) Click Connect to POS (if successfully connected, connect handheld to COMx will be

displayed in bottom left corner)

(2) Click File management

(3) Select storage location of the data file

(4) Select the file you want to upload

(5) Click Upload to PC

2. Download the files from PC to handheld

(1) Click Connect to POS (if successfully connected, connect handheld to COMx will be

displayed in bottom left corner)

(2) Click File management

(3) Select the file you want to download to handheld

(4) Click Download to POS

4 Service and Warranty

Dynaflox follows the enterprise culture of "Respect, Harmony, Innovation and Integrity",

respect the interests of our customers, we solemnly promise to you:

21
 Dynaflox Wireless IR Handheld Operator manual
1. From the date of delivery, meters enjoy one year free warranty.

2. If user demands, the company will appoint professional technician to help users solve

the problem at the first time.

3. Dynaflox will not be responsible for and will have no obligation under the Warranty to

the following situations:

1) Damage caused by human factors, such as smashing, wrestling, etc.

2) Damage caused by irresistible factors, such as lightning, etc.

3) The product is opened, modified or repaired by any person other than a technician from

Dynaflox or if it is repaired using unauthorized parts.

4) Damages caused by failing to follow the instructions of the manual to install, use or

maintain the meter.

5) For the above reasons the maintenance expenses should be borne by users.

Dynaflox Shanghai Co., Ltd.

Add: No.106 Qianpu Road, Eastern New Area, Songjiang Industrial Zone, Shanghai
201611, China
Tel: 0086-21-67602289Fax: 0086-21-67602287
E-mail:[email protected] [email protected]
Website: www.dynaflox.com www.ultradwatermeter.com

* The Company reserves the right to modify the information of the products. It is subject to change without notice

* Publication Date:June, 2015

22