Product 

Change Notification 06947 
(1/2018) 

ProTechTPS 
Overview 
On January 30, 2018, Woodward will be releasing new “preferred” ProTechTPS models and a
new Field Software Conversion kit. The new ProTechTPS models include the same functionality
as the older ProTechTPS models but include many product improvements and enhancements
requested by product line users throughout the past years. After January 30, 2018, Woodward
recommends that customers who are purchasing ProTechTPS units for use in new applications
order part numbers from the “preferred” part number list only.
This ProTechTPS software update provides enhanced math/computational functionality and adds
over 100 logic blocks for use when programming this safety logic solver for a specific application.
The new Field Software Conversion kit can be purchased and used to upgrade/convert older
ProTechTPS models in the field to the new “preferred” ProTechTPS models by simply
uploading/installing the latest software program. Refer to below description of changes for a list of
the improvements and enhancements available. Refer to product manuals 35059v1 & 35059v2
for detailed product information on these new “preferred” ProTechTPS models.

Description of Changes 
The new ProTechTPS software program is based on the older ProTechTPS software program
and includes the below listed improvements/enhancements.
New features
The following new computational blocks were added:
1. MULTIPLY block. Provides the product of all configured inputs. Up to five inputs per block.
Quantity 5.
2. DIVIDE block. Performs a divide function on the two inputs. Quantity 5.
3. ADD block. Provides the sum of all configured inputs. Up to five inputs per block. Quantity 5.
4. NEGATE block. Supports subtraction functionality by providing the negative value of the input.
Quantity 10.
Added the following new support blocks:
1. CURVE block (polygon): A 2-dimensional lookup based on a single, configured analog input. Up
to six breakpoints (coordinate pairs) can be defined. Values between breakpoints are
interpolated. Values beyond table-defined min or max are limited - equal to first or last point,
respectively; Quantity 2.
2. SWITCH block: Outputs one of two analog input values based on the status of the control input.
Example usage: selecting a default value for a calculation if an analog input is failed; Quantity
10.
3. CONSTANT block: Allows definition of a fixed analog value to be used in conjunction with the
math/analog blocks; Quantity 40.
4. ANALOG UNIT DELAY block: Loop breaking block for analog signals, to define execution order.
Asserts a unit delay; Quantity 10.
5. COUNTER block: Provides a count indication as well as a comparison output which indicates
when a count threshold is exceeded; Quantity 10.
6. PEAK HOLD block: Captures and holds both maximum and minimum signal values; Quantity 10.
7. PULSE DETECT block: Monitors an analog signal and is used to detect a sudden rise in value
followed by a drop. The output indicates a pulse was detected; Quantity 5.
8. EVENT FILTER block: Provides an indication that an excessive number of events have occurred
within the defined window of time. Typically used in conjunction with the PULSE DETECT;
Quantity 5.
Product Change Notification 06947 p.2

Changes to existing logic blocks:

 Speed Loss (sudden speed loss): made the failure threshold configurable and expanded the
action selection to include ‘not used’.
 Analog Output: Changes the source for the analog output to be configurable, allowing it to be
connected to analog logic blocks.
 Analog Redundancy Manager: Added a difference detection to the Analog Redundancy Manager
blocks, providing a difference comparison between the three inputs. The difference indication is
provided if the threshold is exceeded for the configured time delay.
 Difference Detect: Modified the block inputs to allow connection to any of the internal analog
logic signals (previously allowed connection to shared input signals only).
 Analog Inputs: Increased the allowed range of the analog inputs to +/- 999999.
 LAG blocks: Added a derivative (rate of change) output value to the LAG block for use in the
configurable logic. The lag time constant data type was changed from a fixed-selection
enumerated list to a numerical value from 0.004 to 10.
 Resettable Trip: Modified the function input to allow connection to any of the internal Boolean
logic signals (previously allowed connection to discrete input 1-10 only).
 Auto Sequence Test: Added the test result displayed on the front-panel for the entire sequence,
not just the local module. Removed the Continue Input selection, allowing the Start Input to
provide both functions. Added inter-module halt option.
 The analog comparator ON and OFF inputs were modified to allow connection to any of the
internal analog logic signals (previously these were constant values).
 Change the User Defined Test set input to edge triggered so the test does not repeat if set is left
true.
 Logic execution rate changes: The discrete inputs are scanned at 1 ms (previously 4ms) and the
configurable logic runs at 8ms (previously 4ms).
Note: all speed, acceleration, trip, and output functions are unchanged.
Other Improvements and Additions:
 Chinese language support added as a configuration setting.
 Increased allowable ranges for speed settings from 32000 to 80000 rpm to facilitate turbo-
expander applications. The maximum speed frequency remains at 32kHz.
 A configurable low-pass filter was added to the acceleration signal.
 Front Panel Display changes:
o Speed display: The precision of the speed value on the front panel provides one decimal
precision when below 100 rpm. Configurable filtering added to the displayed speed value.
o Improved tront panel performance was improved, providing faster response to a key press.
o Analog Input display: Expanded the front panel display of the analog input to show the level
setpoints (e.g. Hi, Lo) as well as all the level status indications.
o Trip button (front panel): Toggles display between the Trip Log and the Trip Latch.
o Alarm button (front panel): Toggles display between the Alarm Log and the Alarm Latch.
o Added Shared Reset, Shared Start, and Shared Speed Fail Override display screens.
o Trip Latch inputs were rearranged to display more practical faults first (e.g. overspeed).
o Modbus: A) Included the outputs of all analog logic blocks as Modbus analog/register reads.
B) The address numbering (Boolean and register) changed to be consecutive, removing
huge gaps in numbering. C) Added Spare Boolean read registers to prevent errors
experienced by devices that queried in increments of 16. D) Added 20 scalable analog reads,
allowing the user to select the source and set the signal scaling (for very large or very small
analog signals).
 Expanded the configurable logic Boolean connections to include both the local and shared
signals for start, reset, and speed fail override.
 New logic connections added:
o Local and Shared Start
o Local and Shared Reset
o Local and Shared Speed Fail Override
o ARM block Difference Detected
o Outputs from the new analog blocks
Product Change Notification 06947 p.3

 Configuration Checking enhancements implemented:

o Power-up trip (trip relay must be set for de-energize for trip)
o configuration mismatch (function must be enabled)
o Speed fail alarm (function must be enabled and local speed must enabled)
o Speed Fail Trip and Speed Fail Timer (function must be enabled and speed must be
enabled)
GAP Programming Environment Updated
Updated the ProTechTPS GAP/simulation tool to include the firmware updates in this release.
This tool allows users to program the ProTechTPS using graphical function block code. 9927-
2151 Revision B or newer is required. Refer to manual 26712 for details on this tool.
This tool provides the following:
 Graphical view of entire application
 Completeness check to ensure the program will be accepted by the device
 Documented feedback of the ProTech CRC codes to ensure program ‘fingerprint’ verifying laptop
GAP program & installed ProTech settings
 GAP Block help clarifying the function and input/output fields of each block
 Built-in simulation on the user PC to allow testing/debugging of logic
 Simulation that allows manual entry (control) of Input signals

Compatibility Notes and Table 
 Field Software Conversion kit 8929-037 is compatible with and can be used to convert most older
ProTechTPS models to the newer models listed below. See table below for compatibility
information.
Description Part Numbers that Can Be Converted
ProTechTPS – Bulkhead Mount, HV/LV, Ind. Relays 8237‐1248 Rev D or Newer or 8237-1602
ProTechTPS – Bulkhead Mount, HV/HV, Ind. Relays 8237‐1249 Rev D or Newer or 8237-1603
ProTechTPS – Bulkhead Mount, HV/LV, Voted Relays 8237‐1250 Rev D or Newer or 8237-1604
ProTechTPS – Bulkhead Mount, HV/HV, Voted Relays 8237‐1251 Rev D or Newer or 8237-1605
ProTechTPS – Panel Mount, HV/LV, Ind. Relays 8237‐1371 Rev D or Newer or 8237-1606
ProTechTPS – Panel Mount, HV/HV, Ind. Relays 8237‐1372 Rev D or Newer or 8237-1607
ProTechTPS – Panel Mount, HV/LV, Voted Relays 8237‐1373 Rev D or Newer or 8237-1608
ProTechTPS – Panel Mount, HV/HV, Voted Relays 8237‐1374 Rev D or Newer or 8237-1609
ProTechTPS – Field Software Conversion Kit 8929-037

 Only ProTechTPS Service Tool (9927-1684 Rev. F or newer) is compatible with both new and old
ProTechTPS models. Note that the latest revision of this service tool can be obtained/ downloaded
from Woodward’s website
 Configuration files from older ProTechTPS models can be loaded into new ProTechTPS models
using the ProTechTPS service tool. However, configuration files from new ProTechTPS models
cannot be loaded into older ProTechTPS models.
Product Change Notification 06947 p.4

Preferred Model Numbers 
The following table shows the new/improved “preferred” ProTechTPS part numbers:

Non-Preferred Preferred Part

Description
Part Number Number
ProTechTPS – Bulkhead Mount, HV/LV, Ind. Relays 8237-1602 8237-2602
ProTechTPS – Bulkhead Mount, HV/HV, Ind. Relays 8237-1603 8237-2603
ProTechTPS – Bulkhead Mount, HV/LV, Voted Relays 8237-1604 8237-2604
ProTechTPS – Bulkhead Mount, HV/HV, Voted Relays 8237-1605 8237-2605
ProTechTPS – Panel Mount, HV/LV, Ind. Relays 8237-1606 8237-2606
ProTechTPS – Panel Mount, HV/HV, Ind. Relays 8237-1607 8237-2607
ProTechTPS – Panel Mount, HV/LV, Voted Relays 8237-1608 8237-2608
ProTechTPS – Panel Mount, HV/HV, Voted Relays 8237-1609 8237-2609

Customer Action 
1. Customers who are currently using any ProTechTPS model and do not require any of the above listed
changes/improvements should take no action. Woodward is committed to supporting the listed “non-
preferred” models for a period of 20 years after inactivation. Refer to the related product support plan
for these models.
2. After January 30, 2018, Woodward recommends that customers who are purchasing ProTechTPS
units for use in new applications order part numbers from the “preferred” part number list only.
3. After January 30, 2018, customers who currently own an older ProTechTPS model and wish to
have/utilize one or more of the above listed changes/improvements can send their old ProTechTPS
model into Woodward Colorado, USA for a conversion to a new model. Optionally, they can purchase
Field Software Conversion Kit 8929-037 and schedule a field conversion by an authorized Woodward
field service engineer. Please contact your Woodward representative to schedule model conversions.
The following are trademarks of Woodward, Inc.:
 MicroNet
 ProTech
The following are trademarks of their respective companies:
 Modbus (Schneider Automation Inc.)

Copyright © Woodward, Inc. 2018

All Rights Reserved

PO Box 1519, Fort Collins CO 80522-1519, USA

1041 Woodward Way, Fort Collins CO 80524, USA
Phone +1 (970) 482-5811
Email and Website—www.woodward.com
Woodward has company-owned plants, subsidiaries, and branches, as well as authorized distributors and
other authorized service and sales facilities throughout the world.
Complete address / phone / fax / email information for all locations is available on our website.