上海奉义龙电子有限公司

Shanghai Fengyilong Electronic Co,. Ltd.

PM835 User Manual

Power Control Electricity Monitoring System

Power Safe Programmable Management Relay

Forlong Power Intelligent Power Meter

Mini Power Mini Power Energy Meter

HPD Harmonic Protection Device

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-1-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

Content
Panel Meter Specifications ……………………………………………………………………….... 3
Panel Meter Operation Manual …………………………………………………………………….. 7
Dimension………… …… ……………………………… ……………………………… ………....20
Wiring Diagram………………………………………………………………………………....…21
Installation………………………………………….…………………… …………………….…..22
Contact…………………………………………………………………………………………….24

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-2-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

PM835 Panel Meter Specification

1 Safety Instruction

1.1 Information for Your Own Safety

This manual does not contain all of the safety measures for operation of this
equipment (module, device) because special operating conditions, local code
requirements or local regulations may necessitate further measures. However, it
does contain information which must be adhered to for your own personal safety
and to avoid damage to the equipment. This information is highlighted by a warning
triangle with an exclamation mark or a lightning bolt depending on the severity of
the warning.

Warning
Means that failure to observe the instruction can result
in death, serious injury or considerable material
damage.

Caution
Means hazard of electric shock and failure to take the
necessary safety precautions will result in death,
serious injury or considerable material damage.

1.2 Qualified personnel

Installation and operation of this equipment described in this manual may only be
performed by qualified personnel.
Only people that are authorized to install, connect and use this equipment and have
the proper knowledge about labeling and grounding electrical equipment and
circuits and can do so according to safety and regulatory standards are considered
qualified personnel in the manual.

1.3 Use for the intended purpose

The equipment (device, module) may only be used for the application cases
specified in the catalog and the user manual and only in connection with devices and
components recommended and approved by Forlong.

1.4 Proper handling

The prerequisites for perfect, reliable operation of the product are proper transport,
storage, installation and connection, as well as proper operation and maintenance.
When operating electrical equipment, certain parts of this equipment carry

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-3-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

dangerous voltages. Improper handling can therefore result in serious injury or

material damage.

 Only use isolated tools suitable for the voltages the meter is used for.
 Do not connect while circuit is live (hot).
 Place the meter only in dry surroundings.
 Do not mount the meter in an explosive area or exposed to dust, mildew
and/or insects.
 Make sure the used wires are suitable for the maximum current of this
meter.
 Make sure the AC wires are connected correctly before activating the
current/voltage to the meter.
 Do not touch the meter’s connection clamps directly with your bare hands,
with metal, blank wire or other conducting material as that will cause an
electric shock and possibly cause injury.
 Make sure the protection cover is placed after installation.
 Installation, maintenance and repair should only be done by qualified
personnel.
 Never break the seals to open the front cover as this might influence the
functionality or accuracy of the meter, and will void all warranty.
 Do not drop, or allow physical impact to the meter as there are high
precision components inside that may break and render the meter
measurement inaccurate.

2 Specifications

2.1 Voltage Inputs

• 20-280 Volts Line To Neutral, 20-480 Volts Line to Line
• Universal Voltage Input
• Input Withstand Capability – Meets IEEE C37.90.1 (Surge Withstand
Capability)
• Programmable Voltage Range to Any PT ratio
• Supports: 3 phase 3 or 4 wires, 400/230V, 110/63V,208/120V
• Burden: 0.36VA per phase Max at 600V, 0.014VA at 120 Volts
2
• Input wire gauge max (AWG 12 / 2.5mm ) PPPP
PPPP

2.2 Current Inputs

• Class : (0 to 5) A, 5 Amp Nominal
• Fault Current Withstand: 100 Amps for 10 Seconds, 300 Amps for 3 Seconds,
500 Amps for 1 Second.
• Programmable Current to Any CT Ratio

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-4-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

• Burden 0.005VA per phase Max at 11Amps

• 5mA Pickup Current
• Pass through wire gauge dimension: 0.177" / 4.5mm
• Continuous current withstand: 20 amps for screw terminated or pass through
current connections

2.3 Isolation
All Inputs and Outputs are galvanically isolated to 2500 Volts AC.

2.4 Environmental Rating

Storage: (-25 to +70)°C
Operating: (-10 to +65)°C
Humidity: to 75% RH Non-Condensing
Faceplate Rating: NEMA12 (Water Resistant)
Environment : IP54 standard, IP65 optional
Mounting Gasket Included

2.5 Sensing Method

• RMS
• Sampling at 120+ Samples per Cycle on all channels measured readings
simultaneously
• Harmonic %THD (% of Total Harmonic Distortion)

2.6 Update Rate

• Watts, VAr and VA-100msec
• All other parameters-1second

2.7 Power Supply

Option D2:
• (65 to 275) Volts AC and (90 to 380) Volts DC. Universal AC/DC Supply
Option D:
• 18-60VDC Burden: 10VA max.

2.8 Communication Format

• 2 Com Ports (Back and Face Plate)
• RS485 Port (Through Back Plate)
• Com Port Baud Rate: (1200 to 115200)
• Com Port Address: 0-247
• 8 Bit, No parity
• Modbus RTU Protocols

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-5-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

2.9 KYZ Pulse

• Type Form A
• On Resistance: 23-35 Ohm
• Peak Voltage: 350 VDC
• Continuous Load Current: 120 mA
• Peak Load Current: 350mA (10ms)
• Off Stat Leakage Current @ 350VDC: 1 mA
• Opto-Isolation: 3750V (6 0Hz, 1min)

2.10 Meter Accuracy

• kWh Better than Class 1 per EN 62053-21 & BS 8431
• Kvarh Better than Class 2 per EN 62053-23 & BS 8431
• kW & kVA Better than Class 0.5 IEC 60688
• kvar Better than Class 0.5 IEC 60688
• Amps & Volts Class 0.2 IEC 60688 (0.01In – 1.2In or 0.1Un – 1.2Un)
• PF ±0.2° (0.05In – 1.2In and 0.2Un – 1.2Un)
• Neutral Current Class 0.5 IEC 60688 (0.05In – 1.2In)

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-6-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

PM835 Operation Introduction

1. Two key mode
Each key has two operating mode. Firstly, the key press down and up
instantly. Secondly, the key press down about 2 second. The first mode, we call
it short-press mode. The second one, we call it long-press mode.
1.1 In measurement status, keys have the follow functions,
please refer to table 1.

Table 1 Keys function in measurement status

Key Key mode Function

Short press Enter display volts amps picture

1.Picture number add 1

Short press 2.Enter display THD ,power factor and frequency
picture

1.Picture number sub 1

Short press
2.Enter display power picture

Short press Enter display energy picture

Long press Enter or exit auto display status

Long press Enter or exit Max Demand status

Long press No function

Long press Enter parameter setting status

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-7-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

1.2 In parameter setting status, keys have the follow

functions, please refer to table 2.

Table 2 Keys function in parameter setting status

Key Key mode Function

Short press Picture number sub 1

1.Picture number add 1

Short press
2.Set the number add 1

1.Picture number sub 1

Short press
2.Set the number sub 1

Short press Picture number add 1

Long press exit current node

Long press No function

Long press No function

Long press Enter next node

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-8-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

2. Display pictures
2.1 If you want to see phase volts, line volts, phase amps
pictures.

Phase volts (picture 1) Line volts(picture 2) Phase amps(picture 3)

Power up , you will see phase volts picture 1.

Step 1, short press ，you will see line volts picture 2.

Step 2, short press , you will see phase amps picture 3.

2.2 If you want to see system power factor, frequency, phase

power factor, volts Total Harmonic Distortion ,amps Total
Harmonic Distortion pictures.

System power factor Phase power factor volts Total Harmonic amps Total Harmonic
and frequency (picture 5) Distortion Distortion
(picture 4) (picture 6) (picture 7)
Power up , you will see phase volts picture 1.

Step 1 , short press , you will see system power factor and frequency picture 4;

Step 2 , short press , you will see phase power factor picture 5.

Step 3 , short press , you will see volts Total Harmonic Distortion picture 6.

Step 4 , short press , you will see amps Total Harmonic Distortion picture 7.

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-9-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

2.3 If you want to see phase watts, phase var, phase VA ,

system power pictures.

Phase watts Phase var Phase VA System power

(picture 8) (picture 9) (picture 10) (picture 11)
Power up , you will see phase volts picture 1.

Step 1 , short press , you will see phase watts picture 8;

Step 2 , short press , you will see phase var picture 9;

Step 3 , short press , you will see phase VA picture 10;

Step 4 , short press , you will see system power picture 11.

In every picture, you can see KWH energy, if you want to see

Kvarh energy , please short press .

（picture 12）

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-10-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

2.4 If you want to see Time-average volts, Time-average amps,

Peak time-average volts, Peak time-average amps, Peak hold
phase volts, Peak hold phase amps pictures.

Time average volts Time average amps Peak time average volts
(picture 13) (picture 14) (picture 15)

Peak time average amps Peak hold phase volts Peak hold phase amps
(picture 16) (picture 17) (picture 18)
Power up , you will see phase volts picture 1.

Step 1 , long press , you will see time average volts picture 13;

Step 2 , short press , you will see time average amps picture 14;

Step 3 , short press , you will see peak time average volts picture 15;

Step 4 , short press , you will see peak time average amps picture 16;

Step 5 , short press , you will see peak hold phase volts picture 17;

Step 6 , short press , you will see peak hold phase amps picture 18.

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-11-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

2.5 If you want to see Max system power factor and Max
frequency, Min system power factor And Min frequency, Volts
Sequence component, Amps sequence component picture.

Max system power Min system power Volts Sequence Amps sequence
factor and Max factor And Min component component
frequency (picture frequency (picture (picture 21) (picture 22)
19) 20)

Power up , you will see phase volts picture 1.

Step 1 , long press , you will see time average volts picture 13;

Step 2 , short press , you will see Max system power factor and Max
frequency picture 19;

Step 3 , short press , you will see Min system power factor And Min
frequency picture 20;

Step 4 , short press , you will see Volts Sequence component picture 21;

Step 5 , short press , you will see Amps sequence component picture 22;

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-12-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

2.6 If you want to see Power system demand, Min MD, Peak
hold MD, Min system power, Max system power pictures.

Power system Min Demand Peak hold

demand (picture 24) Demand
(picture 23) (picture 25)

Min system power Max system

(picture 26) power
(picture 27)
Power up , you will see phase volts picture 1.

Step 1 , long press , you will see time average volts picture 13;

Step 2 , short press , you will see Power system demand picture 23;

Step 3 , short press , you will see Min Demand picture 24;

Step 4 , short press , you will see Max Demand picture 25；

Step 5 , short press , you will see Min system power picture 26;

Step 6 , short press , you will see Max system power picture 27;

If you long press , you will see pictures will auto display
one by one.

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-13-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

2.7 If you want to see individual harmonics, please refer to the

below steps.

Step 1, long press , you will see (picture

28) ,if you input correct password (password is 1000) , press , the

password will change to 1000, then long press , you can enter into

parameter setting main menu (picture 29).

means that this parameter has child files(submenu) . means child file.

means parameter number.

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-14-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

3. Setting parameter
3.1 Set relays status (parameter 0)

Control output relays Output relay 1 type Output relay 1 pulse

status(picture 30) Pulse or level(picture 31) width(picture 32)

Output relay 2 type Output relay 2 pulse

Pulse or level(picture 33) width(picture 34)

Step 1, long press , enter picture 30; long press , you can
set relays open or close.

Step 2, short press , enter picture 31; long press , you

can set relay 1 type.

Step 3, short press , enter picture 32; long press , you

can set relay1 pulse width.

Step 4, short press enter picture 33; long press , you

can set relay2 type.

Step 5, short press enter picture 34; long press ,you

can set relay2 pulse width.

Long press you can exit current status……

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-15-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

3.2 Set Modbus ID (parameter 1)

long press , you can set Modbus ID1-254;

3.3 Set RS-485 Baud Rate (parameter 2)

long press , you can set baud rate (1200, 2400, 4800, 9600, 19200,
38400, 115200)

3.4 Set PT , CT(parameter 3-6)

Set PT primary Set PT secondly Set CT primary Set CT secondly

(Parameter 3) (Parameter 4) (Parameter 5) (Parameter 6)
The PT1 can be set 100-500000;
The PT2 can be set 100-400;
The CT1 can be set 1-9999;
The CT2 can be set 1-10.

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-16-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

3.5 Set backlight time (parameter 7)

Backlight time can be set from 5s to 65535s.

3.6 Set auto display time interval (parameter 8)

Time interval can be set from 500ms to 9999ms.

3.7 Clear energy KWh Kvarh

Clear Kwh(parameter 9) Clear Kvarh(parameter 10)

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-17-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

3.8 Set password (parameter 11)

3.9 Panel meter information (parameter 12)

Meter type Version number Software date

3.10 System type (parameter 13)( customer can’t use this

function)

3.11 Individual Harmonic (parameter 14)

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-18-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

3.12 Set System connect status (parameter 15)

Set phase 1 current Set phase 2 current Set phase 3 current

forward forward forward

Set meter working Set hours run (on Display hours

mode: roads)
3phase 4 wire
3 phase 3 wire

3.13 Set volts, amps, power period (parameter 16)

Set power period Set volts, amps period

(1-60min) (10-1800s)

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-19-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

Dimension

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-20-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

Wiring Diagram

Label in the back of the meter

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-21-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

Installation

Installation method:
1、The dimension of the hole on the Panel:

2、take off the four plastic clamps and install the meter into the hole:

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-22-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

3、then install the four clamps on the meter

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-23-
 上海奉义龙电子有限公司
Shanghai Fengyilong Electronic Co,. Ltd.

Contact

Company Shanghai Fengyilong Electronic Co., Ltd.

Address No.5, Hangdu Road, Hangtou, Pudong, Shanghai,201300，China
Tel +86-21-60975591
Fax +86-21-60975593
E-mail [email protected]
Website www.china-meters.com

www.china-meters.com Email：[email protected] +86-21-60975591/60975593

-24-