Scribd
Upload
46 views6 pages

Mechanical Questions

This document contains a 25 question mechanical module test covering topics like least count of vernier callipers, micrometer vs dial gauge conversions, tire and engine specifications, properties of coolant and brake fluid, gear trains and common rail fuel systems.

Uploaded by

arup
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
46 views6 pages

Mechanical Questions

This document contains a 25 question mechanical module test covering topics like least count of vernier callipers, micrometer vs dial gauge conversions, tire and engine specifications, properties of coolant and brake fluid, gear trains and common rail fuel systems.

Uploaded by

arup
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

G B Pant Institute of Technology, Okhla Phase- III, New Delhi 110020

Automotive Mechatronic Research Center – ADAM Course

Name: _______________________________________________________________________

Module Name: Mechanical Module Time: 50 Minutes


(Each question carries 2 marks)

1. Formula for least count of Vernier Calliper is _____


Ans:

2. What is the major difference between Micrometer and Dial Gauge?

Ans:

3. 260 Kilo Pascal = ____ Bar.

Ans:

4. 25 inch = ___ mm.

Ans:

5. Explain the tyre specification/designation : 245/45R 19-102Y

Ans:

1
6. As per MB specification what is the grade of engine oil , AT fluid and Brake fluid?

Ans:

7. What would be the rpm of camshaft sprocket if crankshaft is rotating with 1000 rpm?

Ans:

8. What would be replaced in every maintenance service of a MB Car?

Ans:

9. What are the reasons for brake fluid level to drop in its reservoir?

Ans:

10. Bolt size is M10×1.5-6g-S. What does this mean? Is this coarse or fine threaded bolt?

Ans:

11. The rail pressure of the Gasoline engine is _____Bar


a. 100 b. 200 c. 300 d. 400

Ans:

2
12. Explain the engine specification : 112 062 2 2 143 347

Ans:

13. Explain the Chassi specification : WDC 166 0 56 6 M 009518

Ans:

14. Write the properties of coolant.


Ans:

15. Write the properties of Brake fluid.


Ans:

3
16. What should be the length of a torque wrench, if 150 Nm torque is required to be applied to
wheel bolts with hand force of 100 Newton?

Ans:

2 5
4
3

Fig: 1

Refer the Fig. 1 above , gear train image and select the correct option

17. Refer Fig.1 : Assuming that gear “1” is rotating in clockwise direction , gear “1” & “2” are
external mesh , gear “2” & “3” are in internal mesh , gear “3” & “4” are external mesh
and gear “4 “ & “5” ar external mesh. Then what will be the direction of gear “5”.

a. Clockwise b. anticlockwise c. Gear locks d. Counter clockwise

Ans:

4
18. Ref. Fig.1: If gear “1” is rotating with 100 rpm, what will be the speed of gear “3” . Following are
the number of teeth’s for each gears. Gear “1” = 32 teeth . Gear “2” = 16 teeth. Gear “ 3” = 8
teeth.

a. 150 rpm b. 300 rpm c. 400 rpm d. 500rpm

Ans:

19. Coolant test is done by ______.

From the Fig. 2 below answer the following questions :

Fig. 2

20. Identify common rails and injectors in the Fig. 2

21. Identify High pressure line and low pressure line in the Fig.2

22. Identify High pressure punp and fuel filter in the Fig. 2

23. Identify fuel return line in the Fig. 2

5
24. Explain venturi effect (ref. fig. 2).

25. _____ bar pressure is in low pressure circuit and _____ bar pressure is maintained in high
pressure circuit. ( ref. Fig.2).

You might also like