Experimental Study On Flexural Behaviour of Fiber Reinforced Geopolymer Ferrocement Folded Panel

Download as pdf or txt
Download as pdf or txt
You are on page 1of 8

International Journal of Advance Research In Science And Engineering http://www.ijarse.

com
IJARSE, Vol. No.4, Special Issue (01), March 2015 ISSN-2319-8354(E)

EXPERIMENTAL STUDY ON FLEXURAL


BEHAVIOUR OF FIBER REINFORCED
GEOPOLYMER FERROCEMENT FOLDED PANEL
C.Manikandan1, S.Dharmar2, S.Nagan3
1
PG Scholar, 2 Associate Professor, Department of Civil Engineering,
P.S.R Engineering College, Sivakasi, (India)
3
Associate Professor, Department of Civil Engineering,
Thiagarajar College of Engineering, Madurai, (India)

ABSTRACT
Ferrocement is a highly adaptable construction material and acquire high performance characteristics,
particularly in cracking, strength, ductility, and impact resistance. The ferrocement reinforcement is uniformly
distributed in both direction and closely spaced through the thickness of the section. There is abundant scope
for mass production and standardization together with the economy in construction. Ferrocement is appropriate
for low-cost roofing, precast units and manhole covers. It is also used for the construction of domes, water
tanks, boats, silos and folded plates. Geopolymer is an innovative revolutionary green material. An
experimental investigation on ferrocement folded panel with geopolymer mortar and polypropylene fiber has
been conducted for various mix proportions and fiber ratio. The results show that the flexural strength of the
folded panel increased with the addition of fiber and also concluded that the addition of fibers increased the
ductility and decreased the crack development and spilling of cement matrix.

Key Words: Fiber, Ferrocement, Folded Panel, Geopolymer Mortar,

I. INTRODUCTION

Geopolymers are a class of new binder generally manufactured by activating an alumino silicate source material
in a highly alkaline medium. For the production of concrete-the most widely used construction material in the
world, Ordinary Portland Cement (OPC) is the main ingredient used which is among the most energy intensive
construction material and whose production is for an increase of 3% annually [1]. The production of OPC
releases large amount of carbon dioxide (CO2) to the atmosphere that significantly contributes to greenhouse gas
emissions. One ton of CO2 is released into the atmosphere for every ton of OPC produced [2]. Therefore, there is
a need to find an alternative type of binder to produce more environmentally friendly mortar. A promising
alternative is the replacement of cement with by product material such as fly ash.
Ferrocement is a highly adaptable form of reinforced concrete. Ferrocement is a building material together of a
relatively thin layer of concrete, covering such reinforcing material as steel wire mesh. The ferrocement has
unique properties such as good tensile strength, toughness, water tightness, fire resistance, resistance to
cracking.

1761 | P a g e
International Journal of Advance Research In Science And Engineering http://www.ijarse.com
IJARSE, Vol. No.4, Special Issue (01), March 2015 ISSN-2319-8354(E)
II. EXPERIMENTAL STUDY
2.1 Material Characterization
2.1.1 Fly ash
Fly ash of Class-F obtained from the Tuticorin Thermal Power Plant is used throughout this study. The chemical
composition of the fly ash, as determined by X-ray fluorescence analysis is given below.
Table 1: Chemical Compositions Fly Ash
S. No. Characteristics % by mass
Silicon di Oxide (Sio2) plus Aluminium Oxide (Al2O3) plus Iron Oxide
1 95.95
(Fe2O3)
2 Silica (as SiO2) 59.71
3 Magnesium Oxide (as MgO) 106
4 Total Sulphur as sulphur tri Oxide (Na2O) Nil
5 Available Alkalis as sodium Oxide (Na2O) 0.63
6 Loss on Ignition 0.91
7 Moisture 0.32
8 Calcium Oxide as CaO 0.50
2.1.2 Fine Aggregate
Sand obtained from Trichy River passing through IS Sieve of 4.75mm and having a Fineness Modulus 2.80 and
Specific Gravity 2.62 conforming to IS 383-1971 Zone II is used in this study.
2.1.3 Water
Specified amount of extra water was used in the mixing. The ordinary Potable water was available in the
concrete laboratory used for the purpose.
2.1.4 Super Plasticizer
Super plasticizer-Conplast SP430 from FOSROC is used to improve the workability of fresh mortar.
2.1.5 Fiber
Recron 3s was used in this study for making the fiber reinforced Geopolymer folded panel. Recron 3s fiber has
more advantages, such as increased ductile property, reduction in water permeability, and increased in
flexibility, high Melting point. Low cast and easily disperses in the cement matrix. Table: 2 shows the properties
of Polypropylene Fiber (Recron 3s).

Fig: 1 Polypropylene Fiber (Recron 3S)

1762 | P a g e
International Journal of Advance Research In Science And Engineering http://www.ijarse.com
IJARSE, Vol. No.4, Special Issue (01), March 2015 ISSN-2319-8354(E)
Table 2 Properties of Polypropylene Fiber (Recron 3S)
S. No. Properties Specifications
1 Effective Diameter 10µ - 1.0 mm
2 Length 6 – 12 mm
3 Specific Gravity 0.91 Kg/m3
4 Water Absorption Less than 0.45 %
5 Melting Point Not less than 160̊ C
6 Aspect Ratio 12
2.1.5 Skeletal Steel
The skeletal steel of 6mm dia Mild Steel @ 100mm c/c both in transverse and in longitudinal direction is used.
The ultimate tensile strength of mild steel is 472 N/mm2.
2.1.6 Wire Mesh
G.I. Wire Mesh with hexagonal openings of size 12mm and wire thickness of 1.29 mm (20gauge) was used.
2.1.7 Sodium Hydroxide (NaOH)
The properties of Sodium Hydroxide are described below:
Assay (Purity) = 97%
Carbonate(Na2co3) = 2%
Chloride (cl) = 0.01%
Sulphate (So4) = 0.05%
Lead (pb) = 0.001%
Iron (Fe) = 0.001%
Potassium (K) = 0.1%
Silicate (Sio2) = 0.05%
Zinc (Zn) = 0.02%
2.1.8 Sodium Silicate ( Na2 SiO3 )
Sodium Silicate, usually known as “water glass" or “liquid glass”, is well-known due to wide commercial and
industrial applications. It is mostly composed of oxygen-silicon polymer backbone lodging water in molecular
matrix pores. Sodium silicate products are manufactured as solids or thick liquids, depending on proposed use.
2.2 Geometry of Folded Ferrocement Panel
The geometry of ferrocement panel is folded shape with dimensions of 1000 mm x 400 mm x 30 mm. The
reference number and designation of the panels are given in Table 6. The panels are constructed using the
conventional ferrocement materials, which is composed of Geopolymer Mortar and Hexagonal Wire Mesh
along with skeletal steel. Fig 2 & Fig 3 shows the geometry and cross-sections of folded panel.

Fig: 2 Cross Sections of Folded Panel Fig: 3 Geometry of Folded Panel


1763 | P a g e
International Journal of Advance Research In Science And Engineering http://www.ijarse.com
IJARSE, Vol. No.4, Special Issue (01), March 2015 ISSN-2319-8354(E)
2.3 Mix Proportions
Table: 3 Mix Proportions for Geopolymer Mortar
Percentage of Polypropylene fiber
Materials
0.0% 0.4%
Fly Ash: Fine Aggregate 1 1
Super plasticizer ( 1% of Fly-ash) 1 1
Fly ash/Alkaline Solution 0.45 0.45
NaOH:Na2Sio3 1:1 1:1
Molarity of NaOH 8M 8M

2.4. Preparation of Control Specimens


Geopolymer Mortar cubes of size 70.6mm × 70.6 mm× 70.6 mm were cast to characterize strength of
the mortar using the mix proportions as described in Table:3 and then cured @70 • C for 24 hours in the heat
curing chamber [3].

Fig. (4) Control specimens

2.5 Casting and Curing of Folded Panels


The required geometry of the folded panel was made using steel mould fabricated to match the shape and size.
Each sample was cast after fixing the required wire mesh and meshes in its proper position in the mould [4]. For
the panels with single wire mesh, the mesh was placed at mid depth of the panel and the mortar mix was
prepared using Sand-Fly ash ratio and Alkaline Solution-Fly ash ratio by weight of 1:1 and 0.45, respectively.
After 24 hours from casting, the samples are removed from the mould and the cured in 24 hours

Fig: 5 Reinforcement Details Of Panel Fig:6 Curing Of Panel In Heat Chamber

1764 | P a g e
International Journal of Advance Research In Science And Engineering http://www.ijarse.com
IJARSE, Vol. No.4, Special Issue (01), March 2015 ISSN-2319-8354(E)
III. TESTING OF FOLDED PANELS

After curing, the slabs are tested under loading frame. The load was applied by means of a load cell 20T. The
specimens were tested by simulating simply supported conditions. The load was applied as two symmetrically
arranged concentrated line loads. Loading was applied using a Hydraulic Jack and LVDT was fixed at central
bottom to measure the deflection. The slabs were painted using whitecem to help in tracing the cracks. The test
setup of the tested trough panel is shown in figure. The load is applied in small increments and simultaneously
the deflection at the center of the panel was recorded during the loading process up to failure. The deflection at
the mid span is measured by LVDT (0 to 50mm). Cracking was carefully checked throughout the loading
process and the corresponding cracking load is also noted. The test results were interpreted using Universal
Digital Data Acquisition System interface with PC and Application Software.

Fig: 7 Loading Setup Fig 8. During Application of Load

IV. RESULTS AND DISCUSSION


Table 4 Designation of Panels
S. No. Specimen ID Description

1 GFP-FD-01 Geopolymer Ferrocement Panel with single layer Mesh


2 FRGFP-FD 01 Fiber reinforced-Geopolymer Ferrocement Panel with single layer Mesh

Fig.9 shows Load Vs Deflection of Geopolymer Folded Panels of without (GFP-FD-01) and with fiber (FRGFP-
FD 01). From that, GFP-FD-01 specimen was deflected suddenly without any caution [7]. The first crack was
formed under the load. The time taken to first crack to ultimate failure is too short. So the failure of the
specimen was rapidly. In FRGFP-FD 01the specimen was deflected after the sufficient formation of cracks [8].
The first crack also was formed under the load and the elapsed time between failures to ultimate is too long. The
above failure of the specimen was restricted by evenly distributing the fiber in tension zone. Table: 5 & Table: 6
shows Load Vs Deflection of the specimens.
Table.7 & 8 shows the Stiffness of Geopolymer Folded Panels of without (GFP-FD-01) and with fiber (FRGFP-
FD 01). From the Fig. 10, the Stiffness of the GFP-FD-01 specimen was higher than the FRGFP-FD 01.
Because of fiber has the resilient property, due to that the stiffness of the matrix was good. Table 9 &10 shows
the Ductility of Geopolymer Folded Panels of without (GFP-FD-01) and with fiber (FRGFP-FD 01). From Fig:
11 the Ductility of the GPFP2A specimen was higher than the GFP-FD-01. Because of the introduction of fiber
in FRGFP-FD 01.

1765 | P a g e
International Journal of Advance Research In Science And Engineering http://www.ijarse.com
IJARSE, Vol. No.4, Special Issue (01), March 2015 ISSN-2319-8354(E)
Table 5 Load Vs Deflection Table: 6. Load Vs Deflection

of GFP-FD-01 of FRGFP-FD 01

Table: 7 Load Vs Stiffness Table: 8 Load Vs Stiffness


of GFP-FD-01 of FRGFP-FD 01

1766 | P a g e
International Journal of Advance Research In Science And Engineering http://www.ijarse.com
IJARSE, Vol. No.4, Special Issue (01), March 2015 ISSN-2319-8354(E)
Table: 9 Load Vs Ductility Table: 10 Load Vs Ductility
For GFP-FD-01 For FRGFP-FD 01

Fig :9 Load Vs Deflection Curve for GPF-FD 01 & FRGFP-FD 01

Fig : 10 Load Vs Stiffness Curve for Fig: 11 Load Vs Ductility Curve for
GPF-FD 01 & FRGFP-FD 01 GPF-FD 01 & FRGFP-FD 01

1767 | P a g e
International Journal of Advance Research In Science And Engineering http://www.ijarse.com
IJARSE, Vol. No.4, Special Issue (01), March 2015 ISSN-2319-8354(E)
V. CONCLUSIONS

Based upon the Experimental test results of geopolymer folded panel without and with fiber the following can
be stated.
1. Flexural strength of Geopolymer Folded Panel with Fiber is more when compared with Geopolymer Folded
Panel of without fiber.
2. The ductility of Geopolymer Folded Panel with Fiber is increased because of introduction of fiber in the mix..
3. The mode of failure is changed from sudden failure as exhibits in Panels without fiber because of introduction
of fiber in the mix and allows sufficient time before failure after yielding.

REFERENCES

[1] S. Thokchomet et al., “Performance of fly ash based Geopolymer Mortar in Sulphate Solution”, Journal of
Engineering Science & Technology Review, 3,(1), 2010, pp.36-40.
[2] Nagesh M. Kulkarni., "Analysis and Design of ferrocement Panels an Experimental Study”, (IJIES), Vol. 1,
No.5, April 2013.
[3] V. Sreevidya, R. Anuradha, D. Dinakar, Dr. R. Venkatasubramani (2012) “Acid Resistance of Flyash Based
Geopolymer Mortar under Ambient Curing And Heat curing” International Journal of Engineering Science
and Technology, Vol. 4, No.02 pp 681-684.
[4] B. V. Rangan, Pan, Zhu and Sanjayan, Jay G (2009), "An investigation of the mechanisms for strength gain
or loss of geopolymer mortar after exposure to elevated temperature", Journal of Material Science. Vol.44,
No.7, pp.1873-1880.
[5] Mohana Rajendran, Nagan Soundarapandian “An Experimental Investigation on the Flexural Behavior of
Geopolymer Ferrocement Slabs.” Journal of Engineering and Technology, Jul-Dec 2013, Vol 3, Issue 2.
[6] R.Vicent prabakar, S.Dharmar. “Experimental Investigation on Flexural Behavior of Folded Ferrocement
Panels”, International Journal of Innovative Research in Science, Engineering and Technology, vol3, Issue7,
july 2014.

BIOGRAPHICAL NOTES
Mr. C .Manikandan is presently pursuing M. E. final year in Civil Engineering Department (Specialization in
Structural Engineering) from P.S.R. Engineering College, Tamil Nadu, India.
Mr. S. Dharmar is working as a Associate Professor in Civil Engineering Department, P.S.R. Engineering
College, and presently pursuing Ph. D. from Anna University, Tamil Nadu, India.

1768 | P a g e

You might also like