Installation Guide: Smartax Ma5600T Multi-Service Access Module V800R008C02
Installation Guide: Smartax Ma5600T Multi-Service Access Module V800R008C02
Installation Guide: Smartax Ma5600T Multi-Service Access Module V800R008C02
V800R008C02
Installation Guide
Issue 01
Date 2011-01-15
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or representations
of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.
Website: http://www.huawei.com
Email: support@huawei.com
Intended Audience
This document describes the entire process for installing the N63E-22 cabinet for indoor access
solutions in terms of installation preparations, cabinet installation, cable routing, and power-on
check.
The intended audience of this document is:
l Installation engineers
l Technical support engineers
Symbol Conventions
The following symbols may be found in this document. They are defined as follows.
Symbol Description
Update History
Updates between document issues are cumulative. Therefore, the latest document issue contains
all updates made in previous issues.
Contents
7 Ending Installation....................................................................................................................7-1
7.1 Sealing Cable Holes........................................................................................................................................7-2
7.1.1 Sealing Holes for Power Cables and Ground Cables.............................................................................7-2
E Cable Labels...............................................................................................................................E-1
E.1 Introduction to Labels....................................................................................................................................E-3
E.2 Filling Labels..................................................................................................................................................E-5
E.3 Usage of Labels..............................................................................................................................................E-7
E.4 Attaching Labels.............................................................................................................................................E-9
E.5 Label for External Alarm Cables..................................................................................................................E-11
E.6 Label for Network Cables............................................................................................................................ E-12
E.7 Labels for Optical Fibers..............................................................................................................................E-14
E.8 Labels for Trunk Cables...............................................................................................................................E-16
E.9 Label for Subscriber Cables......................................................................................................................... E-19
E.10 Labels for DC Power Cables......................................................................................................................E-20
E.11 Labels for AC Power Cables......................................................................................................................E-22
F Environment Requirements.....................................................................................................F-1
F.1 Storage Environment Requirements...............................................................................................................F-2
F.2 Transportation Environment Requirements....................................................................................................F-4
Figures
Figure 1-1 Configuration of the N63E-22 cabinet installed with one service subrack .......................................1-4
Figure 1-2 Configuration of the N63E-22 cabinet installed with two service subracks ..................................... 1-5
Figure 1-3 Configuration of the N63E-22 cabinet installed with one service subrack and one SPL subrack
...............................................................................................................................................................................1-6
Figure 2-1 Straightening the tongue...................................................................................................................2-18
Figure 2-2 Removing the cover..........................................................................................................................2-18
Figure 2-3 Removing the wooden panels...........................................................................................................2-19
Figure 2-4 Unpacking the carton........................................................................................................................2-20
Figure 2-5 Unpacking the board.........................................................................................................................2-21
Figure 3-1 Removing the front door of the cabinet..............................................................................................3-2
Figure 3-2 Removing the screws on side covers..................................................................................................3-3
Figure 4-1 A cabinet installed on a concrete floor...............................................................................................4-3
Figure 4-2 Several cabinets installed on a concrete floor.....................................................................................4-4
Figure 4-3 Process of installing the cabinet on a concrete floor.......................................................................... 4-5
Figure 4-4 Construction plan drawing for installing a single cabinet on a concrete floor...................................4-8
Figure 4-5 Construction plan drawing for installing cabinets side by side on a concrete floor...........................4-9
Figure 4-6 Construction plan drawing for installing cabinets back to back on a concrete floor..........................4-9
Figure 4-7 Marking-off plate for a concrete floor..............................................................................................4-10
Figure 4-8 Drilling a hole...................................................................................................................................4-12
Figure 4-9 Components of an expansion bolt....................................................................................................4-13
Figure 4-10 Installing an expansion bolt............................................................................................................4-14
Figure 4-11 Removing the spring washer, flat washer, and nut.........................................................................4-14
Figure 4-12 Removing the front door of the cabinet..........................................................................................4-16
Figure 4-13 Removing the air filter....................................................................................................................4-17
Figure 4-14 Placing the cabinet..........................................................................................................................4-18
Figure 4-15 Leveling the cabinet........................................................................................................................4-19
Figure 4-16 Fastening the cabinet......................................................................................................................4-20
Figure 4-17 Testing the resistance......................................................................................................................4-21
Figure 4-18 Connecting the connecting plates...................................................................................................4-22
Figure 5-1 A single cabinet installed on an ESD floor.........................................................................................5-3
Figure 5-2 A row of cabinets installed on an ESD floor......................................................................................5-4
Figure 5-3 Process of installing the cabinet on an ESD floor..............................................................................5-5
Figure 5-4 Construction plan drawing for installing a single cabinet on an ESD floor.......................................5-8
Figure 5-5 Construction plan drawing for installing cabinets side by side on an ESD floor...............................5-9
Figure 5-6 Construction plan drawing for installing cabinets back to back on an ESD floor..............................5-9
Figure 5-7 Marking-off plate for the ESD floor of the cabinet..........................................................................5-11
Figure 5-8 Drilling a hole...................................................................................................................................5-12
Figure 5-9 Components of an expansion bolt....................................................................................................5-13
Figure 5-10 Installing an expansion bolt............................................................................................................5-14
Figure 5-11 Removing the spring washer, flat washer, and nut.........................................................................5-14
Figure 5-12 Position of the height-locking bolt.................................................................................................5-15
Figure 5-13 Installing the support......................................................................................................................5-16
Figure 5-14 Leveling and fastening the support.................................................................................................5-17
Figure 5-15 Removing the front door of the cabinet..........................................................................................5-18
Figure 5-16 Removing the air filter....................................................................................................................5-19
Figure 5-17 Placing the cabinet..........................................................................................................................5-20
Figure 5-18 Leveling the cabinet........................................................................................................................5-21
Figure 5-19 Fastening the cabinet......................................................................................................................5-22
Figure 5-20 Testing the resistance......................................................................................................................5-23
Figure 5-21 Connecting the connecting plates...................................................................................................5-24
Figure 5-22 Process of recovering the ESD floor..............................................................................................5-25
Figure 5-23 Installing the floor holder...............................................................................................................5-25
Figure 6-1 Installing the OT terminals.................................................................................................................6-3
Figure 6-2 Bundling the cables at the bending radius..........................................................................................6-4
Figure 6-3 Leading the cables through the cable ladder.......................................................................................6-5
Figure 6-4 Leading the cables downwards from the side of the cable trough......................................................6-6
Figure 7-1 Installing the air filter.........................................................................................................................7-3
Figure 7-2 Installing the front door of the cabinet...............................................................................................7-4
Figure 7-3 Connecting the ground cable..............................................................................................................7-5
Figure 7-4 Installing the screws on side covers...................................................................................................7-6
Figure B-1 Process for installing an indoor cable rack........................................................................................B-5
Figure B-2 Distance between bracket angles.......................................................................................................B-6
Figure B-3 Drilling holes.....................................................................................................................................B-7
Figure B-4 Ceiling-based installation..................................................................................................................B-8
Figure B-5 Ceiling-based installation when there is an obstacle on the ceiling..................................................B-9
Figure B-6 Distance between bracket angles.......................................................................................................B-9
Figure B-7 Drilling holes...................................................................................................................................B-10
Figure B-8 Ground-based installation...............................................................................................................B-11
Figure B-9 Fixing a U-steel as the beam onto the cable ladder.........................................................................B-11
Figure B-10 Distance between deltoid frames...................................................................................................B-12
Figure B-11 Drilling holes.................................................................................................................................B-12
Figure B-12 Installing the cable rack against the wall.......................................................................................B-13
Figure B-13 Installing a grounding cable..........................................................................................................B-13
Figure B-14 Assembling cable ladders..............................................................................................................B-14
Figure B-15 Turning the cable ladders (without cable trays) on the same level...............................................B-15
Figure B-16 Turning the cable ladders on different levels................................................................................B-16
Tables
Table 2-1 Measuring and marking tools to be arranged before the installation...................................................2-3
Table 2-2 Drilling tools to be arranged before the installation.............................................................................2-3
Table 2-3 Fastening tools to be arranged before the installation..........................................................................2-4
Table 2-4 Pliers to be arranged before the installation.........................................................................................2-5
Table 2-5 Auxiliary tools to be arranged before the installation..........................................................................2-7
Table 2-6 Special tools to be arranged before the installation..............................................................................2-9
Table 2-7 Meters to be arranged before the installation.....................................................................................2-10
Table 2-8 Checklist of the construction environment........................................................................................2-11
Table 2-9 Checklist for the power supply system..............................................................................................2-13
Table 2-10 Checklist of the grounding system...................................................................................................2-14
Table 2-11 Checklist for the cable tray..............................................................................................................2-15
Table 2-12 Checklist for the distribution frame.................................................................................................2-16
Table 2-13 Checking requirements before unpacking the products...................................................................2-17
Table 7-1 Checklist of the cabinet installation.....................................................................................................7-7
Table 7-2 Internal connections of the N63E-22 cabinet that is configured with two service subracks (I-type PDU
adopted).................................................................................................................................................................7-9
Table 7-3 Internal connections of the N63E-22 cabinet that is configured with two service subracks (B-type PDU
adopted)...............................................................................................................................................................7-10
Table 7-4 Checklist of signal cables...................................................................................................................7-10
Table 7-5 Checklist of the terminal installation.................................................................................................7-12
Table 7-6 Checklist of power cables and ground cables....................................................................................7-13
Table 7-7 Checklist of the installation environment..........................................................................................7-14
Table 7-8 Checklist of the telecommunications room........................................................................................7-15
Table 7-9 Checklist of the connectivity of cables..............................................................................................7-16
Table A-1 Dimensions and weight of the N63E-22 cabinet................................................................................A-1
Table B-1 Components for installing a cable rack...............................................................................................B-2
Table B-2 Tools for installing a cable rack..........................................................................................................B-4
Table C-1 Mapping between the cross-sectional area and the length of insulation layer to be peeled off (L1)
..............................................................................................................................................................................C-3
Table C-2 Mapping between the cross-sectional area and the length of the insulation layer to be peeled off (L1)
..............................................................................................................................................................................C-5
Table C-3 Wires assigned to the network cable..................................................................................................C-9
Table C-4 Peeled lengths of commonly used coaxial cables.............................................................................C-15
Table C-5 Peeled lengths of commonly used coaxial cables.............................................................................C-20
1 Equipment Overview
This topic provides the dimensions of the N63E-22 cabinet and describe the application,
appearance, and configuration of the indoor N63E-22 cabinet for the MA5600T.
1.2 Configuration
The N63E-22 cabinet adopts the DC power. This topic describes the service subrack
configuration of the N63E-22 cabinet, and lists the maximum number of subscribers of the
cabinet.
The N63E-22 cabinet has the following configurations:
l Configuration of one service subrack
l Configuration of two service subracks
l Configuration of one service subrack and one SPL subrack
Figure 1-1 Configuration of the N63E-22 cabinet installed with one service subrack
82
PDU (100 mm) 81
79
38
82, 79 (I-type)
PDU 82, 79 (C3-type)
33
81, 79 (B-type)
30
Service shelf (450 mm) 29
Service shelf 38, 33, 26, 21
26
Cabling space 20, 19, 18, 17
21
20
Cabling space (100 mm) 19
18
17
NOTE
l In Figure 1-2, the filled holes are for floating nuts to fasten subracks.
l In Figure 1-2, installation holes 29, and 30 are used to fasten coils.
Figure 1-2 Configuration of the N63E-22 cabinet installed with two service subracks
82
PDU (100 mm) 81
79
Empty (50 mm)
76
71
64
59
58
57
Cabling space 2 (100 mm) 56
55
NOTE
l In Figure 1-2, the filled holes are for floating nuts to fasten subracks.
l In Figure 1-2, installation holes 29, 30, 67, and 68 are used to fasten coils.
l In Figure 1-2when the High-density service boards are installed, the air deflector is required. When
the other boards are installed, the air deflector is not required.
Figure 1-3 Configuration of the N63E-22 cabinet installed with one service subrack and one
SPL subrack
82
PDU (100 mm) 81
79
Empty (50 mm)
76
71
64
59
58
53
43
42
41
Part Installation Hole
Cabling space (100 mm)
82, 79 (I-type)
PDU 82, 79 (C3-type)
81, 79 (B-type)
NOTE
l In Figure 1-3, the filled holes are for floating nuts to fasten subracks.
l In Figure 1-3, installation holes 50, 51, 67, and 68 are used to fasten coils.
Prepare the tools and the meters before installing the cabinet, and check the installation
environment to ensure that the device is installed properly.
Table 2-1 Measuring and marking tools to be arranged before the installation
Name Description Illustration
Drilling Tools
Table 2-2 lists the drilling tools to be arranged before the installation.
Fastening Tools
Table 2-3 lists the fastening tools to be arranged before the installation.
Pliers
Table 2-4 lists the pliers to be arranged before the installation.
Auxiliary Tools
Table 2-5 lists the auxiliary tools to be arranged before the installation.
Special Tools
Table 2-6 lists the special tools to be arranged before the installation.
Meters
Table 2-7 lists the meters to be arranged before the installation.
3 Air conditioner l During the month when the atmospheric temperature is highest
in a year, install an air conditioner (which can be restarted after
power-off) if the temperature in the telecommunications room
is higher than 35°C.
l Ensure that the air from the air conditioner is not directed
towards the device.
4 Weight bearing l Before installing the cabinet, check the weight bearing capacity
capacity of the installation site according to the device layout of the
installation site. If the bearing capacity does not meet the
requirement, prepare the installation site so that it can bear the
weight of the device.
l Consult a professional construction company and take proper
measures for strengthening the installation site. The
strengthening process must be executed by a professional
construction team.
6 Temperature l If the average temperature is lower than 5°C for 90 days or more
regulation in a year, install a heating system.
l If the average temperature is lower than 5°C for 60 days or more
but fewer than 90 days, it is recommended that you install a
heating system.
8 Lightning proof l The telecommunications room must be installed with the surge
measures protection devices, such as lightning proof rod or lightning
proof strip.
l The lightning protection ground and the protection ground of
the room should share one ground body.
9 Transportation The transportation passage, such as lift and corridor, must be large
passage enough to carry the cabinet.
10 Fire protection l Configure the fire retardant cover for the reserved holes on the
equipment floor, and ensure that the holes can be sealed for
insulation. If cable routing is required, fill the holes with fire-
protection mud.
l Adopt fire retardant materials for the new decoration in the
telecommunications room. For example, adopt fire retardant
materials for insulation when the telecommunications room is
in the buildings or stores.
l Process fire protection by using PVC fire retardant tape, and
fill the holes for cables with fire-protection mud.
l The fire-fighting equipment such as fire extinguisher must be
available in the telecommunications room.
2 Power Each output load of the power distribution cabinet must meet the
distribution requirement for device running, and provide standby capacity for
cabinet the upgrade and capacity expansion of the cabinet.
3 Power cable The power cable that connects the power distribution cabinet to the
device must be far away from the signal cable. The signal cable and
power cable cannot be routed in parallel. If the signal cable and
power cable are routed in parallel, take corresponding shielding
measures.
1 Grounding Do not connect the neutral line of the AC power cable to the
protection ground of any telecom device in the telecommunications
room.
Do not install the fuse or switch on the ground cable.
Ensure that all the ground cables are short and arranged straightly.
3 Collective Use the ground ring or ground bar for the collective ground cable.
ground cable Do not use aluminum cables as ground cables. Take measures to
prevent electrification corrosion when connecting different metal
parts together.
Use the copper busbar as the collective ground cable with the cross-
sectional area of not smaller than 120 mm2, or use the galvanized
flat steel that has the same resistance.
4 Grounding Connect the ground bar properly to the grounding network. The
lead-in cable distance between the ground bar and the grounding network should
not be more than 30 m. Use 40 x 4 mm2 or above galvanized flat
steel to connect them, or use a cable with a cross-sectional area of
more than 95 mm2 to connect them.
Take insulation and anti-corrosive measures for the galvanized flat
steel and the cable. The galvanized flat steel and the cable should
not be broken. Take mechanical measures for the unearthed part.
5 DC grounding The central office, where the device is located, should adopt joint
grounding. That is, the working ground and the protection ground
of the device, and the lightning ground of the building should be
connected together.
Connect the working ground in the DC power distribution cabinet
to the protection ground in the telecommunications room. The cross-
sectional area of the cable should not be smaller than 95 mm2.
1 Bearing The cable tray and the wall that supports the cable tray must bear
capacity the cables routed in the telecommunications room.
2 Installation The installation position of the cable tray must comply with the
standard design. The cable tray and its accessories must be installed correctly
and reliably.
4 Grounding Connect the cable tray to the ground bar. The ground lead-out cable
is the copper conducting wire with a cross section that is greater
than or equal to 50 mm2.
1 Capacity The distribution frame capacity must meet both current capacity
requirements and further capacity requirements.
5 Grounding The shield layer of the external cable must be connected to the
ground bar of the MDF. The ground led-out cable of the MDF is the
copper conducting wire with a cross section that is no less than 50
mm2. Use the copper cable with a cross section that is no less than
6 mm2 as the DDF/ODF to connect to the protection-ground bar in
the telecommunications room.
The project supervisor must check the products on site in the presence of the customer. Table
2-13 describes the checking requirements before unpacking the products.
No. Description
2 The packing case must be in proper condition. It should not be damaged or damp.
3 The shockproof label and overturn-proof label on the packing case must be displayed
correctly.
5 The total number of packages must be consistent with the number of items
mentioned in the packing list attached to the packing case.
NOTE
l If the package is defective, stop unpacking and report the condition of the package to the local Huawei
representative. If the quantity of the product is correct and the product is in good condition, unpack
and accept the product.
l To identify the front, rear, left, and right sides of the device, read the instructions on the packing case.
Precautions
l Do not place the wooden case upside down because the device may be damaged severely.
l Move the packing case into or near the telecommunications room (if possible) to prevent
the cabinet from being damaged during transportation.
l Remove the packing blocks and the lining boards from the installation site to prevent the
signal cables and circuit boards from being damaged.
l If the products are wet or rusty, stop unpacking and detect the cause. Report the condition
of the products to the local Huawei representative.
l When unpacking the carton, take protection measures, for example, wear gloves to protect
your hands.
Procedure
Step 1 Insert one end of the spanner into the groove of the tongue on the cover of the wooden case.
Turn the spanner to straighten the tongue, as shown in Figure 2-1. You can also use a screwdriver
or a claw hammer to straighten the tongue.
Tongue Spanner
Step 2 Remove the cover after straightening all the tongues on the cover, as shown in Figure 2-2.
Step 3 Straighten all the tongues that join the wooden panels around the wooden case and remove the
wooden panels, as shown in Figure 2-3.
Step 4 After unpacking, place the cabinet aside to unpack other cases.
----End
Precautions
l When unpacking the carton, take protection measures, for example, wear gloves to protect
your hands.
l Cut the tapes along the seams of the carton cover by using a knife. Make sure that you cut
only the tapes without damaging the contents of the carton.
l If the products are wet or rusty, stop unpacking and detect the cause. Report the condition
of the products to the local Huawei representative.
Procedure
Step 1 Read the carton label to obtain the information about the number and the type of the board in
the carton.
Step 2 Cut the straps by using the diagonal pliers.
Step 3 Cut the pressure-sensitive adhesive tapes along the seams of the carton cover by using a knife.
Step 4 Open the carton and take out the foam plates.
Step 5 Cross-check the contents of the box of the board. Ensure that the number of the boards listed on
the labels of the board box is consistent with the number listed on the labels of the carton, and
then take out the board box. Figure 2-4 shows how to unpack the carton.
Foam plate
Strap
Board box
Carton label
----End
Precautions
CAUTION
Electronic components are sensitive to the ESD. When handling the board, wear the ESD gloves
or the ESD wrist strap that is grounded properly and hold only the edge of the board.
NOTE
The desiccant in the ESD bag is used for absorbing moisture inside the bag.
Procedure
Step 1 Check whether the board package is damaged. If the board packet is damaged, stop unpacking
and report the condition to the local representative office. If the board package is in good
condition, proceed as follows.
Step 2 Wear the ESD gloves or the ESD wrist strap and connect its ground end to the ESD jack on the
cabinet.
Step 3 Unpack each package and check for damages. Figure 2-5 shows how to unpack the board.
Board
Board box ESD bag
Step 4 Select one of the following methods for processing the board.
If... Then...
Step 5 Place all the materials on the antistatic surface to discharge the static electricity, and then install
the board.
Step 6 Use the original package materials for packing the board. Keep them in a dry and cool place,
away from sunlight and strong electromagnetic radiation sources.
----End
Procedure
Step 1 Check the product type and quantity according to the Packing List. Sign the document on site.
Step 2 Check each product according to the Packing List. If there is a mismatch in the number of
packages, or if the cargo is damaged, or if the consignment is wrong, sign the Unpacking
Memo. The project supervisor should also fill in the Cargo Inspection Feedback Form and report
the problem to the local representative office within three days.
Step 3 Store the unpacked product in a room if the product does not match the contents of the Packing
List. Take photographs of the storage site, the rusty or corroded product, and the case or package
material. Archive the photographs and store the empty case and materials.
Step 4 Unpack other packages after confirming the contents of one package.
Step 5 The project supervisor and the customer must sign the Packing List.
----End
Before installing the cabinet, remove the cabinet doors, including the front door and the side
cover.
Procedure
Step 1 Remove the ground cable that connects to the front door of the cabinet, leaving one end of the
cable on the rack, as shown in Figure 3-1 (1).
Step 2 Pull down the upper hook pin, and pull the front door outwards to remove it, as shown in Figure
3-1 (2) and (3).
CAUTION
When placing the cabinet door, ensure that the lock is open. This prevents the lower lock rod
from being distorted when it is pulled out.
----End
Context
NOTE
l Check whether to remove the side cover of the cabinet according to actual conditions, such as the flexibility
of routing external cables.
l For combined cabinets, remove the two outmost side covers only.
Procedure
Step 1 Use a Phillips screwdriver to remove the screws from bottom to top and keep the screws properly,
as shown in Figure 3-2.
----End
This topic describes how to install the N63E-22 cabinet on a concrete floor, including marking
reference lines, drilling holes, installing expansion bolts, placing the cabinet, and leveling the
cabinet.
After leveling the cabinet, fasten the expansion bolts at the bottom of the cabinet to fasten the
cabinet.
4.11 Testing the Resistance
After installing the cabinet, test the resistance between the cabinet and the ground, and check
whether the cabinet is insulated correctly.
4.12 Attaching Cabinets
When installing multiple cabinets, you need to connect the connecting plates at the top of the
cabinet to fasten the cabinets.
Figure 4-3 shows the process of installing the cabinet on a concrete floor.
Start
Drill holes
Attach cabinets
End
1. Recommended Tools
To facilitate the installation, prepare the required installation tools. Test and adjust the
meters and special tools before using them.
l Hammer drill
l Multimeter
l Claw hammer
l Rubber hammer
l Flat-head screwdrivers: M3–M6
l Phillips screwdrivers: M3–M6
l Adjustable wrench
l Socket wrenches: M6, M8, M12, M14, M17 and M19
l Steel tape
l Marker pen
l Powder marker
l Spirit level
l Angle square
l Vacuum cleaner
l Ladder
Test and adjust the meters and special tools before using them.
Precautions
Pay attention to the following points when installing the cabinet:
l Lock the cabinet door before carrying the cabinet to protect the components and cables.
l Ensure that the cabinet is powered off before the installation.
l If the cabinet surface is scratched, paint it.
l Check the cabinet completely before the installation, and rectify the faults in time.
l After installing the cabinet, clean the cabinet if it is dirty.
l You can change the installation methods according to the actual situation based on this
guide.
Procedure
Step 1 Check the space in and around the cabinet.
l Reserve a space of 400 mm vertically at the bottom of the cabinet for installing the expansion
bolts. If the space is insufficient, remove certain parts from the lower part of the cabinet. For
how to install and remove the parts, see "Installing and Removing the Shelf."
l Reserve sufficient space around the cabinet for maintenance, ventilation, and heat dissipation.
For more information about the space to be reserved, see "4.5 Marking Reference Lines."
Step 2 Check the quantity of cabinets and accessories.
The accessories include the expansion bolts used for fastening the cabinet.
----End
Mark the position of the cabinet based on the construction plan drawing to confirm the positions
of the expansion bolts.
4.5.2 Marking Reference Lines Based on the Marking-off Plate
Mark the position of the cabinet based on the delivered marking-off plate to confirm the positions
of the expansion bolts.
Figure 4-4 Construction plan drawing for installing a single cabinet on a concrete floor
Front Unit: mm
Wall or reference object
≥1000
Right Left
Back 600
413
4- Φ16
Cabinet outline
187
300
≥ 800
≥100
Expansion ≥ 800
bolt hole
Figure 4-5 shows the construction plan drawing for installing cabinets side by side.
Figure 4-5 Construction plan drawing for installing cabinets side by side on a concrete floor
Front Unit: mm
≥1000
Right Left Wall or reference object
Expansion 600
Back 4-Φ16
bolt hole 413 ≥ 800
Cabinet outline
300
187
≥800
≥100 600
Figure 4-6 shows the construction plan drawing for installing cabinets back to back.
Figure 4-6 Construction plan drawing for installing cabinets back to back on a concrete floor
Unit: mm
≥ 1000
300
300
Cabinet outline
≥ 800
≥ 1000
Procedure
Step 1 Based on the reference object, mark several points by using the measuring tape, and then draw
two parallel lines, with the spacing of 187 mm between them.
Step 2 Mark the position of the first expansion bolt for the cabinet on the two lines.
Step 3 Mark the positions of the other three expansion bolts based on the position of the first expansion
bolt.
Step 4 To install a row of cabinets, refer to the marked hole positions and mark the positions of the
holes for other cabinets one by one.
Step 5 Measure all the lines and check the position of the holes again. Ensure that the dimensions of
the holes are correct.
----End
Precautions
When installing a cabinet next to the existing cabinet, ensure that the edge of the marking-off
plate is in level with the edge of the existing cabinet.
Marking-off Plate
Figure 4-7 shows the marking-off plate.
Front
Unit: mm
Right Left
Expansion bolt hole Back
187 300
413
600
Procedure
Step 1 Place the marking-off plate on the floor based on the layout of the cabinet. The semi-circle notch
on the marking-off plate identifies the front direction of the cabinet.
Step 2 Mark holes for all the expansion bolts based on the marking-off plate, that is, four holes for each
cabinet.
----End
Precautions
Pay attention to the following when you drill the holes:
l Use a punch tool to chisel a hole so that you can position the drill bit if the floor is very
hard or slippery.
l Hold the drill firmly and ensure that the drill bit is vertical to the floor. The drill should be
steady when you drill holes to avoid uneven or slanting holes.
l Ensure that all the holes are of equal depth.
Procedure
Step 1 Select a Ф16 drill bit.
Step 2 Drill a hole by using a hammer drill on the marked position of the expansion bolt, as shown in
Figure 4-8. The depth of the hole must be equal to the length of the expansion tube plus the
length of the expansion nut, and the depth of the hole should range from 52 mm to 60 mm.
Hole depth
Step 3 Remove the dust from the hole by using a vacuum cleaner.
Step 4 Measure the depth of the hole and the distance between the holes. Mark and drill a hole again
if the depth or distance is wrong.
----End
Structure
Figure 4-9 shows the components of an expansion bolt.
Flat washer
Spring washer
Expansion bolt
Expansion tube
Guide trough
Expansion nut
Guide rib
Precautions
l Insert the guide rib into the guide trough beforehand. Otherwise, the expansion bolt cannot
be fastened.
l Ensure that the expansion tube is completely inserted into the concrete pedestal. The length
of the expansion tube should not exceed the depth of the floor. Otherwise, the installation
of the cabinet is affected.
Procedure
Step 1 Insert the expansion bolt into the hole.
Step 2 Do not fasten the spring washer, flat washer and nut on the expansion bolt very tightly.
Step 3 Knock the expansion bolt by using a rubber hammer or a claw hammer until the expansion tube
is completely inserted into the expansion hole, as shown in Figure 4-10.
Step 4 Fasten the expansion bolt clockwise by using a spanner to expand the tube.
Step 5 Remove the spring washer, flat washer, and nut by turning them anticlockwise, as shown in
Figure 4-11.
Figure 4-11 Removing the spring washer, flat washer, and nut
----End
Precautions
Pay attention to the following points when placing the cabinet:
l There are two insulating plates between the cabinet and the floor. The expansion bolt has
an insulating tube. Install the insulating parts correctly during construction so that the entire
device is not connected to the ground before the ground cables are installed.
l Fine fasten the bolts in turn in a diagonal sequence to reduce the stress between the bolt
and the cabinet.
Procedure
Step 1 Remove the front door.
1. Remove the ground cable at the front door, leaving one end of the ground cable attached
to the rack, as shown in Figure 4-12 (1).
2. Pull down the hook pin at the upper part of the door and remove the front door, as shown
in Figure 4-12 (2), (3).
CAUTION
Remove and place the cabinet door on the floor and keep them unlock. Otherwise, the lower
latch will slide downwards and may bend and snap.
----End
Procedure
Step 1 Place a spirit level in two orthogonal directions on the top of the cabinet, and check whether the
cabinet is leveled according to the position of the bubble in the spirit level, as shown in Figure
4-15 (1).
Step 2 If the cabinet is not leveled, adjust the corresponding leveling foot to level the cabinet, as shown
in Figure 4-15 (2).
----End
Procedure
Step 1 Check whether the spring washer, flat washer, and the insulating washer are installed on the bolt
correctly.
Step 2 Fasten the bolt in a diagonal sequence with a torque of 45 Nm, as shown in Figure 4-16.
----End
Insulation Requirement
The resistance between the cabinet and the ground should be more than five megohms.
Procedure
Step 1 Set the multimeter to the megohm level to measure the resistance between the expansion bolt
and the cabinet, as shown in Figure 4-17.
If... Then...
The measured resistance value is more than or equal to The resistance testing is complete
5 megohms
Step 3 Remove all installation components, and check whether the insulating components are missing
or whether the insulating components are damaged.
----End
Precautions
l To attach multiple cabinets, proceed with this topic. Otherwise, skip this topic.
l If multiple cabinets are attached, mark reference lines, install, fasten and attach the cabinets
based on one cabinet.
l Ensure that the cabinets to be attached are installed.
Procedure
Step 1 Ensure that the connecting plates are installed at the top of the cabinet.
Step 2 Remove the connecting plates from the top of the cabinet, and then connect them again.
l Install cabinets back to back, as shown in Figure 4-18 (1).
l Install cabinets side by side, as shown in Figure 4-18 (2).
Step 3 After the cabinets are attached, use the spirit level to check whether they are leveled. If not, level
the cabinets again.
----End
This topic describes how to install the N63E-22 cabinet on an ESD floor.
Start
Drill holes
Attach cabinets
End
l Claw hammer
l Rubber hammer
l Flat-head screwdrivers: M3–M6
l Phillips screwdrivers: M3–M6
l Adjustable wrench
l Socket wrenches: M6, M8, M12, M14, M17 and M19
l Steel tape
l Marker pen
l Powder marker
l Spirit level
l Angle square
l Vacuum cleaner
l Ladder
Test and adjust the meters and special tools before using them.
Precautions
Pay attention to the following points when installing the cabinet:
l Lock the cabinet door before carrying the cabinet to protect the components and cables.
l Ensure that the cabinet is powered off before the installation.
l If the cabinet surface is scratched, paint it.
l Check the cabinet completely before the installation, and rectify the faults in time.
l After installing the cabinet, clean the cabinet if it is dirty.
l You can change the installation methods according to the actual situation based on this
guide.
Procedure
Step 1 Check the space in and around the cabinet.
l Reserve a space of 400 mm vertically at the bottom of the cabinet for installing the expansion
bolts. If the space is insufficient, remove certain parts from the lower part of the cabinet.
l Reserve sufficient space around the cabinet for maintenance, ventilation, and heat dissipation.
For more information about the space to be reserved, see "5.5 Marking Reference Lines."
The accessories include the expansion bolts used for fastening the cabinet.
----End
You can mark reference lines based on the construction plan drawing or the marking-off plate.
Ensure that the reference lines are marked correctly before the installation.
5.5.1 Marking Reference Lines Based on the Construction Plan Drawing
Mark the position of the cabinet based on the construction plan drawing to confirm the positions
of the expansion bolts.
5.5.2 Marking Reference Lines Based on the Marking-off Plate
Mark the position of the cabinet based on the delivered marking-off plate to confirm the positions
of the expansion bolts.
Figure 5-4 shows the construction plan drawing for installing a single cabinet.
Figure 5-4 Construction plan drawing for installing a single cabinet on an ESD floor
Front Unit: mm
≥ 1000
≥ 800
≥ 800
≥100
Expansion
bolt hole
Figure 5-5 shows the construction plan drawing for installing cabinets side by side.
Figure 5-5 Construction plan drawing for installing cabinets side by side on an ESD floor
Front Unit: mm
≥1000
Right Left Wall or reference object
Expansion 600
Back 4-Φ16
bolt hole 448 ≥ 800
Cabinet outline
300
200
≥800
600
≥100
Figure 5-6 shows the construction plan drawing for installing cabinets back to back.
Figure 5-6 Construction plan drawing for installing cabinets back to back on an ESD floor
Unit: mm
≥ 1000
600 Wall or
reference object
448
4 -Φ16
≥ 800
200
300
300
Cabinet outline
≥ 800
≥ 1000
NOTE
After the support is installed, the left, right, and rear sides of the support cannot exceed the dimensions of the
bottom of the cabinet.
Procedure
Step 1 Based on the reference object, mark several points by using the measuring tape, and then draw
two parallel lines, with the spacing of 200 mm between them.
Step 2 Mark the position of the first expansion bolt for the cabinet on the two lines.
Step 3 Mark the positions of the other three expansion bolts based on the position of the first expansion
bolt.
Step 4 To install a row of cabinets, refer to the positions of the marked holes and mark the positions of
the holes for other cabinets one by one.
Step 5 Measure all the lines and check the position of the holes again. Ensure that the dimensions of
the holes are correct.
----End
Precautions
When installing a cabinet next to the existing cabinet, ensure that the edge of the marking-off
plate is in level with the edge of the existing cabinet.
Figure 5-7 Marking-off plate for the ESD floor of the cabinet
Front
Unit: mm
Right Left
Expansion bolt hole Back
200 300
448
600
Procedure
Step 1 Place the marking-off plate on the floor based on the layout of the cabinet. The semi-circle notch
on the marking-off plate identifies the front direction of the cabinet.
Step 2 Mark holes for all the expansion bolts based on the marking-off plate, that is, four holes for each
cabinet.
----End
Precautions
Pay attention to the following when you drill the holes:
l Use a punch tool to chisel a hole so that you can position the drill bit if the floor is very
hard or slippery.
l Hold the drill firmly and ensure that the drill bit is vertical to the floor. The drill should be
steady when you drill holes to avoid uneven or slanting holes.
l Ensure that all the holes are of equal depth.
Procedure
Step 1 Select a Ф16 drill bit.
Step 2 Drill a hole by using a hammer drill on the marked position of the expansion bolt, as shown in
Figure 5-8. The depth of the hole must be equal to the length of the expansion tube plus the
length of the expansion nut, and the depth of the hole should range from 52 mm to 60 mm.
Hole depth
Step 3 Remove the dust from the hole by using a vacuum cleaner.
Step 4 Measure the depth of the hole and the distance between the holes. Mark and drill a hole again
if the depth or distance is wrong.
----End
Structure
Figure 5-9 shows the components of an expansion bolt.
Flat washer
Spring washer
Expansion bolt
Expansion tube
Guide trough
Expansion nut
Guide rib
Precautions
l Insert the guide rib into the guide trough beforehand. Otherwise, the expansion bolt cannot
be fastened.
l Ensure that the expansion tube is completely inserted into the concrete pedestal. The length
of the expansion tube should not exceed the depth of the floor. Otherwise, the installation
of the cabinet is affected.
Procedure
Step 1 Insert the expansion bolt into the hole.
Step 2 Do not fasten the spring washer, flat washer and nut on the expansion bolt very tightly.
Step 3 Knock the expansion bolt by using a rubber hammer or a claw hammer until the expansion tube
is completely inserted into the expansion hole, as shown in Figure 5-10.
Step 4 Fasten the expansion bolt clockwise by using a spanner to expand the tube.
Step 5 Remove the spring washer, flat washer, and nut by turning them anticlockwise, as shown in
Figure 5-11.
Figure 5-11 Removing the spring washer, flat washer, and nut
----End
Procedure
Step 1 Adjust the height of the support.
1. Adjust the height of the support. Ensure that the height of the support is the same as the
height of the ESD floor.
2. Fasten the height-locking bolt with a torque of 45 Nm.
3. Align the position of the support, and measure the length of the diagonals. Ensure that the
length deviation of the diagonals cannot exceed 2 mm, as shown in Figure 5-13 (3).
4. Fasten all bolts by using the combination wrenches, as shown in Figure 5-13 (4).
----End
Precautions
Pay attention to the following points when placing the cabinet:
l There are two insulating plates between the cabinet and the floor. The expansion bolt has
an insulating tube. Install the insulating parts correctly during construction so that the entire
device is not connected to the ground before the ground cables are installed.
l Fine fasten the bolts in turn in a diagonal sequence to reduce the stress between the bolt
and the cabinet.
Procedure
Step 1 Remove the front door.
1. Remove the ground cable at the front door, leaving one end of the ground cable attached
to the rack, as shown in Figure 5-15 (1).
2. Pull down the hook pin at the upper part of the door and remove the front door, as shown
in Figure 5-15 (2),(3).
CAUTION
Remove and place the cabinet doors on the floor and keep them unlock. Otherwise, the
lower latch will slide downwards and may bend and snap.
----End
Procedure
Step 1 Place a spirit level in two orthogonal directions on the top of the cabinet, and check whether the
cabinet is leveled according to the position of the bubble in the spirit level, as shown in Figure
5-18 (1).
Step 2 If the cabinet is not leveled, adjust the corresponding leveling foot to level the cabinet, as shown
in Figure 5-18 (2).
----End
Procedure
Step 1 Check whether the spring washer, flat washer, and the insulating washer are installed on the bolt
correctly.
Step 2 Fasten the bolt in a diagonal sequence with a torque of 45 Nm, as shown in Figure 5-19.
----End
Insulation Requirement
The resistance between the cabinet and the ground should be greater than five megohms.
Procedure
Step 1 Set the multimeter to the megohm level to measure the resistance between the bolt and the
cabinet, as shown in Figure 5-20.
If... Then...
The measured resistance value is larger than or equal The resistance testing is complete
to 5 megohms
Step 3 Remove all installation components, and check whether the insulating components are omitted
or the insulating components are damaged.
Step 4 Fasten the cabinet and test the resistance again.
----End
Precautions
l To attach multiple cabinets, proceed with this topic. Otherwise, skip this topic.
l If multiple cabinets are attached, mark reference lines, install, fasten and attach the cabinets
based on one cabinet.
l Ensure that the cabinets to be attached are installed.
Procedure
Step 1 Ensure that the connecting plates are installed at the top of the cabinet.
Step 2 Remove the connecting plates from the top of the cabinet, and then connect them again.
l Install cabinets back to back, as shown in Figure 5-21 (1).
l Install cabinets side by side, as shown in Figure 5-21 (2).
Step 3 After the cabinets are attached, use the spirit level to check whether they are leveled. If not, level
the cabinets again.
----End
Process
Figure 5-22 shows the process of recovering the ESD floor.
Start
End
Procedure
Step 1 Install the floor holder. Fasten the floor holder to the support by using the bolt M12 x 30, spring
washer and flat washer, as shown in Figure 5-23.
Step 2 Adjust the height of the holder to align the top surface of the holder with the bottom surface of
the ESD floor.
Step 3 Cut and recover the floor. According to the conditions around the cabinet, cut the floor to a
proper size and lay the floor around the cabinet.
----End
6 Routing Cables
Installing OT Terminals
Abide by the following rules when installing two or more OT terminals on one stud, as shown
in Figure 6-1.
l Do not overlap the OT terminals. If there are two or more OT terminals to be installed on
one stud, maintain a 45 degree angle between the two OT terminals.
l Place the larger OT terminal under the smaller OT terminal.
Bending Cables
Abide by the following rules when bending the cables:
l To prevent the cable cores from being damaged, do not apply too much force when bending
the cables at the turning, especially to the trunk cables and the optical fibers.
l The bending radius of the cable should be more than twice the size of the cable diameter.
The bending radius near the connector is four to six times the cable diameter.
l The bending radius of the optical fiber should be more than 20 times the cable diameter.
In general, the bending radius of the optical fiber is greater than or equal to 40 mm.
Bundling Cables
Abide by the following rules when bundling the cables:
l Bundle the cables on both sides of the bending radius by using cable ties, as shown in
Figure 6-2.
l Bundle the cables evenly with equal space between cable ties. Space two adjacent ties 250
mm at most (the subscriber cables should be bundled every 200 mm). When the cables are
bundled outside the cabinet, the space between the cable ties is subject to the space between
the beams (if the beams are not available, the space between the cable ties must be 250 mm
at most).
l Bundle the cable with the cable ties properly. Do not bundle the cables, especially the optical
fibers, very tightly.
l Arrange all cable ties in the same direction. The cable ties should not have any sharp points
at the ends.
l Coil the extra optical fibers and cables neatly.
l Fix the protective caps on the optical fiber connectors that are not currently used.
l Ensure that the cable connectors made on site meet the requirements, and are firm, reliable,
and neat.
l Arrange the bundled cables close to each other, without crossing or twisting them.
l You may not bundle the cables when the cables pass the side of the subrack, but ensure
that the cables are arranged neatly without crossing or twisting them.
Arranging Cables
Abide by the following rules when arranging the cables:
l Place the cables in a proper order and keep the sheath intact.
l Do not apply too much force when bundling the cables.
l Route different types of cables separately.
l Route the cables according to the construction plan drawing, such as the specifications,
path, cross-sectional area, and position.
l Take future maintenance and capacity expansion into account when arranging the cables
and the ports.
l Bundle every eight cables together. When less than eight cables are reserved, bundle them
together. Arrange the cables hierarchically. The adjacent binders should be interconnected
to ensure that all cables are arranged together after routing.
Routing Cables
Cables can be routed in the overhead cabling or underfloor cabling.
Abide by the following rules when routing the cables in the overhead cabling:
l All cables are laid on the cable tray over the cabinet.
l If the distance between the cable tray and the holes at the top of the cabinet is less than or
equal to 0.8 m, route the cables directly through the holes. If the distance between the cable
tray and the holes is more than 0.8 m, you need a climbing ladder to hold the cables to
protect the cables from being damaged.
l If the cable ladder is used, the cables should be led through the cable ladder, as shown in
Figure 6-3.
l If the cable trough is used, the cables should be lead downwards from the side of the cable
trough, as shown in Figure 6-4.
Figure 6-4 Leading the cables downwards from the side of the cable trough
Abide by the following rules when routing the cables in the underfloor cabling:
l All the cables are placed under an ESD floor or routed along the cable trough.
l When the cables are placed under an ESD floor, the height of cable bundles should not
exceed three-fourth of the net height under an ESD floor.
l If the optical fibers are routed inside the cabinet, do not use the same route for the optical
fibers and the power cable or do not cross or twist them.
l Fix the protective caps (plugs) on the optical fiber connectors that are not currently used.
l Smoothen both ends of the corrugated pipe to protect optical fibers.
l Check whether the optical connector is dirty before the installation. If the optical connector
is dirty, clean the connector with a piece of dust-free cotton cloth or a fiber cleaning box.
l The metal hole for the optical fibers must have a smooth and round surface.
l Lead the optical fibers through the corrugated pipe before bringing them into the cabinet.
l When routing the optical fibers (including leading them through the corrugated pipe), make
sure that the tensile force on the optical fiber does not exceed 100 N.
l The length of each corrugated pipe inside the cabinet should be less than 100 mm. The
corrugated pipes should be fastened and bundled firmly.
l The bending radius of the optical fiber should be more than 20 times the cable diameter.
In general, the bending radius of the optical fiber is more than 40 mm.
l Do not look into the fiber end because the laser radiation can damage your eyes.
l Place the optical fiber pairs in a proper order and bind them carefully by using the optical
binders. The optical fibers should not have sharp edges.
l Use the fiber management tray or the cable tie to fasten the optical fibers. The optical fiber
should not have protruding components along its path. Place the large-power heat source
at least 10 mm away from the optical fiber.
l For the optical fiber that is led into the central office, if the metal reinforcing rib is included,
connect the reinforcing rib properly to the protection ground bar in the telecommunications
room.
7 Ending Installation
In the end phase of device installation, you need to seal cable holes, install the cabinet door, and
check device installation and perform the power-on check.
Cut the plastic cover according to the cross-sectional area occupied by the power cables and the
ground cables at the hole. Install the rest of the plastic cover on the cable hole to seal the hole.
The optical fibers are lead into the corrugated pipe, and then routed into the cabinet. After routing
the optical fibers, use an adhesive tape to seal the entry of the corrugated pipe.
Procedure
Step 1 Install the air filter at the bottom of the cabinet as follows.
1. Push the air filter into the bottom of the cabinet along the slide rails.
2. Press down the air filter to the buckles, as shown in Figure 7-1.
4. Connect the ground cable between the front door of the cabinet and the cabinet, as shown
in Figure 7-3.
----End
Procedure
Step 1 Connect the ground cable between the side cover of the cabinet and the cabinet.
Step 2 Install the side cover of the cabinet to the cabinet, and fasten the screws that are used for fastening
the side cover of the cabinet by using the Phillips screwdriver from top downward, as shown in
Figure 7-4.
----End
Context
You can use a label or a list to mark the cabinet. Choose one of them according to actual
conditions.
Procedure
Step 1 You can print or write the cabinet information on the label. The cabinet information includes
the cabinet name, cabinet function, owner, and contact.
Step 2 Attach the cabinet label to the upper left of the front door of the cabinet.
----End
1 The cabinet (chassis) must be stable, and must comply with the Observe
shockproof requirements in the project files.
5 The active parts of the cabinet must function in the normal state. Observe
6 Other connecting bolts of the cabinet must be installed correctly Refer to this
and properly. The flat washers and the spring washers must be document
installed in the correct sequence (install the flat washers, and
then install the spring washers).
7 The paint on the surface of cabinet should not flake, there Observe
should not be any dent on the surface of the cabinet, and the
surface of the cabinet should not be dirty. Otherwise, paint the
cabinet again or clean it.
9 The cabinet (chassis) must be placed according to the project Check the
files. installation
position
10 Insulating parts must be installed between the delivered support Observed and
(foot filling pad) and the ground, floor holder and slide rail confirmed by the
according to the requirements. Ensure that the insulation is customer
provided. The filling pad made by the customer must meet the
requirements.
12 The cabinet rows near the main aisle must be aligned in a Measure
straight line, with a deviation of less than 5 mm.
13 The surfaces of the cabinets in a row must be in one plane, and Observe
the cabinets must be installed close to each other and in proper
order.
14 The boards can be inserted and removed smoothly. If the front Refer to this
panel of the board has screws, fasten the screws properly so that document
it is easy to remove them when required. The spring wires must
be intact.
16 The floor gaps around the cabinet are filled. There should not Observe
be any cable ties, screws, or other redundant objects under the
floor.
17 Connect the ESD wrist strap to the ESD jack on the cabinet. Observe
NOTE
Internal cables are installed before delivery, and they are delivered with the entire device, including the
cabinet, subrack, and board.
The working ground and the protection ground of the room share one ground body.
Table 7-2 Internal connections of the N63E-22 cabinet that is configured with two service
subracks (I-type PDU adopted)
Cable Connection Position 1 Connection Position 2
–48 V feeder cable NEG11 (–) and RTN11 (+) on Socket on the power board in slot 21
the PDU of the first service subrack (from
bottom to top)
–48 V feeder cable NEG12 (–) and RTN12 (+) on Socket on the power board in slot 22
the PDU of the first service subrack (from
bottom to top)
–48 V feeder cable NEG31 (–) and RTN31 (+) on Socket on the power board in slot 21
the PDU of the second service subrack (from
bottom to top)
–48 V feeder cable NEG32 (–) and RTN32 (+) on Socket on the power board in slot 22
the PDU of the second service subrack (from
bottom to top)
Environment Port COM2 on the PDU ESC port on the control board in the
monitoring cable first service subrack (from bottom to
top)
PGND feeder cable Ground point at the bottom Ground point on the front of the
enclosure frame of the cabinet cabinet
PGND feeder cable Ground point at the bottom Ground point on the side cover of
enclosure frame of the cabinet the cabinet
PGND feeder cable Ground point at the top Ground point on the rear of the
enclosure frame of the cabinet cabinet
Table 7-3 Internal connections of the N63E-22 cabinet that is configured with two service
subracks (B-type PDU adopted)
–48 V feeder cable The first 48V1 terminal and Socket on the power board in slot 21
BGND terminal of the PDU of the first service subrack (from
bottom to top)
–48 V feeder cable The second 48V1 terminal and Socket on the power board in slot 22
BGND terminal of the PDU of the first service subrack (from
bottom to top)
–48 V feeder cable The first 48V3 terminal and Socket on the power board in slot 21
BGND terminal of the PDU of the second service subrack (from
bottom to top)
–48 V feeder cable The second 48V3 terminal and Socket on the power board in slot 22
BGND terminal of the PDU of the second service subrack (from
bottom to top)
1 If the fiber patch cords are routed outside the cabinet, protection Observe
measures must be taken, such as the corrugated pipes or the
guide troughs must be used.
2 The connecting points of the fiber patch cords should be clean. Observe
Unused optical connectors and optical ports on the board must
be covered with protective caps (or plugs). When cleaning the
patch cords, clean them according to the requirements.
6 Bundle or fix the cables for expansion to the reserved place in Observe
the cabinet for further capacity expansion.
8 Cables must not be routed over the dissipation net of the Observe
cabinet.
14 The length of the corrugated pipe inside the cabinet must be Observe
shorter than 10 cm, and the corrugated pipe must be fastened
and bundled properly. The notch of the corrugated pipe must
be smooth. Use the insulating tapes for cut resistant measures.
15 When bending cables, ensure that the cables are arranged Observe
neatly. Take protection measures when connecting the cables
with edged ports. For example, use the adhesive tape to wrap
the cable or the mechanical part where they are in contact.
16 The cable labels must be filled in correctly and attached Observed and
properly. The cable labels must be neat, and must face the same confirmed by the
direction. It is recommended that you attach cable labels 2 cm customer
away from the connector. Cable labels can be made in batches
according to the requirements of the customer.
1 The delivered alarm monitoring system, such as MDFs, batteries, and Observe
alarm box must be connected correctly and properly. Protective units
on the MDF must work in the normal state and must be grounded
properly.
2 The NMS device should be installed correctly and must be working Observe
properly.
3 The floppy drive, CD-ROM, keyboard, mouse, and monitor must work Observe
normally. The monitor does not have magnetic deviation.
4 The delivered terminals, NMSs, alarm boxes, and inverters must be Observe
installed according to the engineering design.
6 The cables of the terminal, NMS, and alarm box must be bundled Observe
properly. Cut the redundant parts of the cable ties neatly.
7 The cables of the terminal, NMS, and alarm box must be smooth at the Observe
bending for proper contact.
8 You should be able to open the front cover of the alarm box smoothly. Observe
The keyboard lock must have control functions. The paint on the alarm
box must not flake.
9 A PVC trough should be installed for power cables and signal cables Observe
of the alarm box near the wall. The redundant parts must be placed
under the floor or on the cable rack beside the box.
Table 7-6 lists the checklist of power cables and ground cables.
6 When connecting the power cables and the ground cables to Observe
the DC power distribution cabinet, cut the redundant parts.
The cables cannot be coiled.
7 The PGND cables of the MDF and the DDF must be Observe
connected properly. Adjacent MDFs or DDFS must be
interconnected to the protection ground busbar.
11 All devices with metal shell or partial metal shell inside the Measure
cabinet or chassis should be connected to the protection
ground correctly.
16 The routed power cables and ground cables must be bundled Observe
neatly and in a straight line.
18 The power-on process of the device is normal, the fans rotate Observe
in the normal state, and the alarms should be normal.
5 For the cross-sectional area and the power mode of the PGND Confirmed by
cable of the customer, GND cable of the primary power, and –48 the customer
V cable to the power distribution cabinet or power distribution unit
(PDU), the engineering design or actual delivery of Huawei
counts. The requirements on for running the device and the
requirements for expansion in the future are met.
6 The output current fuse of the power distribution cabinet and the Confirmed by
primary power must meet the requirements for running the device. the customer
2 Configure the fire retardant cover for the reserved holes on the Observe
equipment floor, and ensure that the holes can be sealed for
insulation.
3 Adopt fire retardant materials for the new decoration in the Observe
telecommunications room.
1 The trunk cables from the cabinet to the DDF are connected according to the
Engineering Design.
2 The subscriber cables from the cabinet to the MDF are connected correctly. Check
the connectivity of the cables for each pair on the MDF by using a multimeter
according to the following method.
3 The optical fibers from the cabinet to the ODF are connected correctly.
4 The network cables from the cabinet to the MDF are connected correctly.
This topic provides the dimensions and weight of the N63E-22 cabinet.
Table A-1 lists the dimensions and weight of the N63E-22 cabinet.
NOTE
Specifications
When cables are led from the top of the cabinet, it is recommended to install a cable rack in the
equipment room. All the cables in the equipment room can be laid on the cable rack. In general,
a cable rack consists of a cable ladder, with a cable tray as an optional component.
The specification of Cable ladder and cable tray is 400 mm.
For delivery, the cable ladder is 2.5 m long and the cable tray is 2 m long.
Components
Table B-1 shows the components for installing a cable rack.
Cable ladder
Bracket angle
Cable-through
rack
Component Appearance
U-steel
Cable tray
U-shaped
connecting
piece
Connecting clip
Fixing clip
Movable
bushing
End cover
Component Appearance
deltoid frame
Tools
Table B-2 lists the tools for installing a cable rack.
Measuring tools Measuring tape, ruler (1 m), angle square, spirit level, vertical analyzer,
and multimeter
Drilling tools Percussion drill, matched drill bits (Ф10 bit), and vacuum cleaner
Clamping tools Combination wrench M8, socket wrench, and torque spanner
Pliers Handsaw
l Ceiling-based installation: installing the cable rack by fixing suspenders to the ceiling
l Ground-based installation: installing the cable rack by fixing support levers to the ground
l Install the cable rack against the wall: installing the cable rack by deltoid frames against
the wall
CAUTION
l The spacing between two angles connecting pieces is 440 mm. The spacing between the
suspenders must be an integral multiple of 50 mm. The recommended spacing is 1250 mm.
l For ceiling-based installation or ground-based installation, suspenders or support levers must
be installed outside the cable ladder to facilitate installation of a cable tray.
Procedure
Step 1 Determine the position for installing the cable rack according to the engineering files.
Step 2 Determine the positions for installing bracket angles and mark the positions for drilling holes.
See Figure B-2.
Step 3 Select a Ф10 bit to drill holes at the marked positions, with the hole depth of 60 mm to 65 mm.
See Figure B-3.
CAUTION
When drilling holes, wear safety glasses to prevent injuries to your eyes.
Step 5 According to the height between the cable rack and the ceiling of the equipment room, cut the
U-steel with a proper length as the suspender. Then paint the cut surface.
NOTE
When the required length exceeds 2.5 m, you can connect two U-steels together. For details on the
connection method, see B.5.1 Assembling Cable Ladders.
Step 6 Use the M8x20 bolt and M8 nut to install bracket angles on to both ends of the suspender.
CAUTION
When you fix the suspenders, use big flat washers instead of the flat washers accompanying the
expansion bolts.
Step 7 Fit the insulating plate, angle connecting piece, insulating washer, big flat washer, spring washer,
and M8 nut onto the expansion bolt.
CAUTION
When the cable ladder is equipped with a cable tray, an M8x20 bolt is required to connect the
suspender with the bracket angle. Install the bolt into an upper hole on the suspender. The
distance between the bolt and the cable ladder shall be greater than 40 mm. See Figure B-4.
Step 9 Fasten the M8x20 bolt and M8 nut to 13 N·m with a torch spanner to fasten the cable ladder to
the bracket angle.
Step 10 Use the spirit level to check the levelness of the cable ladder. If the cable ladder is not level,
adjust the elliptical holes on the suspenders and those on the bracket angles.
When there is an obstacle on the ceiling, you can fix a U-steel as the beam onto the cable ladder.
See Figure B-5.
----End
Procedure
Step 1 Determine the position for installing the cable rack according to the engineering files.
Step 2 Determine the positions for installing bracket angles and mark the positions for drilling holes.
See Figure B-6.
Step 3 Select a Ф10 bit to drill holes at the marked positions, with the hole depth of 60 mm to 65 mm.
See Figure B-7.
Step 6 Use the M8x20 bolt and M8 nut to install bracket angles on to both ends of the support lever.
CAUTION
When you fix the support levers, use big flat washers instead of the flat washers accompanying
with the expansion bolts.
Step 7 Fit the insulating plate, angle connecting piece, insulating washer, big flat washer, spring washer,
and M8 nut onto the expansion bolt.
Step 8 Fasten the M8 nut to 13 N·m with a torch spanner.
CAUTION
When the cable ladder is equipped with a cable tray, an M8x20 bolt is required to connect the
support lever with the bracket angle. Install the bolt into a lower hole on the support lever. The
distance between the bolt and the cable ladder shall be greater than 40 mm. See Figure B-8.
Step 9 Fasten the M8x20 bolt and M8 nut to 13 N·m with a torch spanner to fasten the cable ladder to
the bracket angle.
Figure B-8 shows the ground-based installation.
When the span between the support levers is wide, fix a U-steel as the beam onto the cable ladder.
See Figure B-9.
Figure B-9 Fixing a U-steel as the beam onto the cable ladder
----End
Procedure
Step 1 Determine the position for installing the cable rack according to the engineering files.
Step 2 Determine the position for installing the deltoid frame and mark the positions for drilling holes.
See Figure B-10.
Step 3 Select a Ф12 bit to drill holes at the marked positions, with the hole depth of 60 mm to 65 mm.
See Figure B-11.
CAUTION
Ensure that the wall is load bearing.
90 。
60mm-65mm
Step 6 Put the expansion bolts through the installation holes on the vertical beam of the deltoid frame.
Fit the insulating washer, big flat washer, spring washer, and M8 nut onto each expansion bolt.
Step 8 Place the cable ladder on the beam of the deltoid frame. Align the holes at the lower side of the
U-steel of the cable ladder with the installation holes on the beam of the deltoid frame. Fasten
the M8x20 bolt and M8 nut to 13 N·m with a torch spanner. See Figure B-12.
M8
Combinati
on
spanner 13 ± 2N•m
M8 Bolt
----End
Procedure
Step 1 Fasten the grounding cable in the holes at the both sides of the U-steel of the cable ladder by use
a M8 bolt, a toothed pad and a nut, and ensure that the tooth side of the toothed pad clings to the
cable rack.
Step 2 Install a grounding cable in the grounding bar. See Figure B-13.
M8 Nut
Grounding bar
Grounding cable
M8 Bolt
----End
l Use one grounding cable to ground the first and fourth bolts, which are used to connect the
cable ladder to the U-shaped connecting piece.
l Use the other grounding cable to connect the second or third bolt to the second or third bolt
at the other side. See Figure B-14.
NOTE
When the length of the cable ladder is not an integral multiple of 2.5 m, you need to cut the extra part. Then
paint the cut surface.
Figure B-15 Turning the cable ladders (without cable trays) on the same level
CAUTION
If one cable rack is equipped with a cable tray whereas the other without a cable tray, ensure
that the cable ladders and the cable tray are on the same level after installation.
When a segment of cable ladder is equipped with a cable tray, use the bracket angle, bolt, and
nut to connect the two cable ladders. Figure B-16 shows how to connect the two cable ladders.
Figure B-17 shows how to connect the cable ladder to the wall.
The methods for jointing cable ladders include front jointing, side jointing, and oblique jointing.
Procedure
Step 1 Select a segment of cable ladder as the climbing ladder.
Step 2 Use the bracket angle, bolt, and nut to joint the climbing ladder and the cable ladder.
Figure B-18 shows the front jointing of cable ladders.
----End
Procedure
Step 1 Select a segment of cable ladder as the climbing ladder.
Step 2 Use the bracket angle, bolt, and nut to joint the climbing ladder and the cable ladder.
Figure B-19 shows the side jointing of cable ladders.
----End
Procedure
Step 1 Select a segment of cable ladder as the climbing ladder.
Step 2 Use the bracket angle, bolt, and nut to joint the climbing ladder and the cable ladder.
Figure B-20 shows the oblique jointing of cable ladders.
----End
Because cable trays have taper, you can insert the smaller end of one cable tray to the larger end
of the other.
B.6.3 Installing a Cable Tray on a 200 mm or 400 mm Wide Cable Ladder
This topic describes how to install a cable tray on a 200 mm or 400 mm wide cable ladder.
B.6.4 Installing a Cable Tray Sideways
This section describes how to install a cable tray sideways.
When you install a cable tray on a cable ladder, if you need to lengthen the cable ladder, first
lengthen it and then fix it.
The insertion depth shall be smaller than 250 mm. See Figure B-21.
Procedure
Step 1 Place the cable tray on the cable ladder.
Step 2 Use fixing clips to fix the cable tray to the cable ladder. Each segment of cable tray uses four
fixing clips, which are located symmetrically at both sides.
Figure B-22 shows how to install the cable tray on the cable ladder.
----End
Prerequisite
CAUTION
The slope of a cable tray can be slightly smaller than the required angle. Cut off the connecting
rib of the triangle aperture on the edge of the cable tray, as shown in Figure B-23. Then paint
the cut area.
Procedure
Step 1 Cut off the connecting rib of the triangle aperture on the edge of the cable tray, as shown in
Figure B-23. Then paint the cut area.
Figure B-23 Cutting off the connecting rib of the triangle aperture
Step 2 Bend one part of the cable tray with the marking line as the axis to the desired angle.
See Figure B-24.
Step 3 Use fixing clips to fix the cable tray to the cable ladder.
Figure B-25 shows the cable tray installed sideways onto the cabling ladder.
Figure B-25 Cable tray installed sideways onto the cabling ladder
----End
B.7.1 Overview
This section describes how to install the accessories of a cable rack.
B.7.2 Installing Cable-Through Racks
Cable-through racks are often installed on the cable ladder over the cabinet. The number and
installation positions of cable-through racks are based on the actual situation.
B.7.3 Installing End Covers, Movable Bushings, and Baffle Rings
This section describes how to install end covers, movable bushings, and baffle rings.
B.7.1 Overview
This section describes how to install the accessories of a cable rack.
Installing a Cable-Through Rack When the Cable Rack Is Not Equipped with a
Cable Tray
CAUTION
To ensure that the upper surface of the cable-through rack is level with the highest surface of
the cable rack:
l If the cable rack is not equipped with a cable tray, fasten the cable-through rack to the cable
ladder through the upper holes on the cable-through rack.
l If the cable rack is equipped with a cable tray, fasten the cable-through rack to the cable
ladder through the lower holes on the cable-through rack.
Figure B-26 shows how to install a cable-through rack when the cable rack is not equipped with
a cable tray.
Figure B-26 Installing a cable-through rack when the cable rack is not equipped with a cable
tray
Installing a Cable-Through Rack When the Cable Rack Is Equipped with a Cable
Tray
Figure B-27 shows how to install a cable-through rack when the cable rack is equipped with a
cable tray.
Figure B-27 Installing a cable-through rack when the cable rack is equipped with a cable tray
This topic describes how to make the power cable, ground cable, and network cable.
C.1 Making External Power Cables and Ground Cables with Cord End Terminals
This topic describes how to make external power cables and ground cables with cord end
terminals.
C.2 Making External Power Cables and Ground Cables with OT Terminals
This topic describes how to make external power cables and ground cables with OT terminals.
C.3 Making Ordinary Network Cables
This topic describes how to make ordinary network cables.
C.4 Making Shielded Network Cables
This topic describes how to make shielded network cables.
C.5 Making the E1 Cable
This topic describes how to make the E1 cable.
Procedure
Step 1 Use the paper cutter to peel off a section of the insulation layer from the power cable based on
the cross-sectional areas of the power cable conductors. A section of the power cable conductor
with a length of L1 is exposed, as shown in Figure C-1. Table C-1 lists the recommended lengths
of the insulation layer to be peeled off (L1).
Figure C-1 Peeling the insulation layer off the power cable
L1
Power cable
Conductor
CAUTION
When peeling off the insulation layer of the power cable, ensure that the conductor of the power
cable is not scratched.
Table C-1 Mapping between the cross-sectional area and the length of insulation layer to be
peeled off (L1)
1 8
1.5 10
2.5 10
4 12
6 14
10 15
16 15
25 18
35 19
50 26
Step 2 Insert the conductor of the peeled power cable into the cord end terminal, as shown in Figure
C-2.
Figure C-2 Inserting the conductor into the cord end terminal
Power cable
CAUTION
After the cord end terminal is inserted into the power cable, the conductor of the power cable
outside the cord end terminal should not be longer than 1 mm.
Step 3 Select a proper cross-sectional area, and use power cable crimping pliers to clamp the head of
the cord end terminal and the conductor of the power cable, as shown in Figure C-3.
Rough side
----End
Procedure
Step 1 Insert the power cable into the heat shrink tubing A, as shown in Figure C-5.
Step 2 Peel off a section of the insulation layer C from the power cable based on the cross-sectional
areas of the power cable conductors. A section of power cable conductor D with a length of L1
is exposed, as shown in Figure C-4. Table C-2 lists the recommended lengths of the insulation
layer to be peeled off (L1).
Figure C-4 Peeling off the insulation layer of the power cable
C
L1
CAUTION
l When peeling off the insulation layer of the power cable, ensure that the conductor of the
power cable is not scratched.
l If the bare crimping terminals are not provided by Huawei, you can adjust L1 according to
the length of the crimping terminal. L1 = L + (1 or 2) mm.
Table C-2 Mapping between the cross-sectional area and the length of the insulation layer to
be peeled off (L1)
1 7
1.5 7
2.5 7
4 8
6 9
10 11
16 13
25 14
35 16
50 16
NOTE
If you peel off the insulation layer off the power cable properly on site, you can compare the cable with
the connector to be crimped.
Step 3 Insert the bare conductor of the power cable into the OT terminal B, and then press the OT
terminal close to the insulation layer C, as shown in Figure C-5.
Figure C-5 Installing heat shrink tubing and bare crimping terminal
L2
C
CAUTION
After the OT terminal is installed, the length of the bare conductor outside the bare crimping
terminal (L2) must not be more than 2 mm. If the length (L2) of the bare conductor outside the
bare crimping OT terminal is larger than 2 mm, cut the redundant part by using the diagonal
pliers or wire clipper, as shown in Figure C-5.
Step 4 Use the crimping tool to clamp the tail of the bare crimping terminal and the contact part of the
conductor, as shown in Figure C-6.
Figure C-6 Clamping the tail of the bare crimping terminal with the contact part of the conductor
NOTE
Step 5 Push the heat shrink tubing A towards the connector, and cover the crimping area of the bare
crimping terminal and the conductor. Use a hot air gun to heat the heat shrink tubing, as shown
in Figure C-7.
CAUTION
Do not heat the heat shrink tubing for a long time. Otherwise, the insulation layer may be
damaged.
----End
l Ensure that the necessary tools, such as the diagonal pliers, a blade (or knife), and the crimp
pliers, are available.
l Ensure that the materials, such as the RJ-45 connectors, UTP-5 twisted pair, and the jacket,
are available.
l Ensure that the jacket is in proper condition. If the jacket is convex, plucked, or damaged,
cut the improper part off the cable.
Procedure
Step 1 Use the diagonal pliers to cut the cable according to the required length.
Step 2 Put the cable through the boot for 100 mm at least. Ensure that the boot is installed in the correct
direction, as shown in Figure C-9.
100 mm
Step 3 Use a blade or a knife to peel off 20 mm of the jacket, as shown in Figure C-10. Do not damage
the insulation of the wires.
Twisted pair
20 mm
Step 4 Arrange the four pair of wires properly according to the connection sequence of the network
cable.
Step 5 Ensure that the wires are 13 mm to 15 mm long. Cut off the extra length of the wires, arrange
the wires in the correct order, and then insert the wires into the RJ-45 connector, as shown in
Figure C-11. Table C-3 lists the wires assigned to the network cable.
1 White and orange White and orange White and orange White and green
3 White and green White and green White and green White and orange
5 White and blue White and blue White and blue White and blue
7 White and brown White and brown White and brown White and brown
NOTE
In Table C-3, end A and end B refer to both ends of a network cable.
Step 6 Use the crimp pliers to crimp the connector. Ensure that the connector is put correctly in the
crimp pliers. After crimping, the metal cover on the connector must be lower than other area on
the connector.
Step 7 Use a network cable tester or a multimeter to test all wires, and ensure that the wires are connected
properly.
Step 8 Push the boot to cover the RJ-45 connector, as shown in Figure C-12.
----End
Super-UTP-5 cable
Shielded iron cover
Boot
Plastic cover of the
RJ-45 connector
Procedure
Step 1 Install the boot for the RJ-45 connector.
1. Select a cable of proper length and install the boot on the RJ-45 connector of the cable.
2. Use a blade or a knife to peel off 30 mm of the jacket.
3. Use a blade to slit 5 mm on the jacket and install a shielded iron cover on the cable weaving
layer, and then insert the shielded iron cover into the jacket along the crack. Install the boot
and the shielded iron cover correctly, as shown in Figure C-15.
Figure C-15 Installing the boot for the RJ-45 connector and the shielded metal cover
CAUTION
When peeling off the jacket of the power cable, do not damage the cable weaving layer or the
insulation wires.
1. Use the diagonal pliers to cut 20 mm off the cable weaving layer, ground wire, aluminum
foil and polyester band at the head of the cable, and store the wires.
2. Arrange the four twisted pairs properly and insert them into the wire fastening slot. Maintain
the original space for the twisted pairs.
3. Arrange the wires smoothly and straightly at the hole of the cable distribution frame.
Arrange the wires properly and cut off the extra length of the wires along the edge of the
wire fastening slot. Table C-3 lists the wires assigned to the network cable.
4. Install the plastic cover on the wire fastening slot, and then fasten the slot. Push the cover
into the slot until you hear click to ensure that the cover is fitted properly, as shown in
Figure C-16.
3. Use the network cable tester or a multimeter to check and ensure that the wires are connected
properly.
4. Insert the RJ-45 connector into the jacket, as shown in Figure C-17.
----End
C.5.1 Making the E1 Cable with the Straight SMB Female Connector
This topic describes how to make the E1 cable with the straight SMB female connector.
C.5.2 Making the E1 Cable with the Straight SMB Male Connector
This topic describes how to make the E1 cable with the straight SMB male connector.
C.5.3 Making the E1 Cable with the Bent SMB Female Connector
This topic describes how to make the E1 cable with the bent SMB female connector.
C.5.1 Making the E1 Cable with the Straight SMB Female Connector
This topic describes how to make the E1 cable with the straight SMB female connector.
Recommended Tools
The recommended tools for making the E1 cable with the straight SMB female connector are
as follows:
l Wire stripper
l Wire crimping tool
l Diagonal pliers
l Wire clipper
l Electric soldering iron
l Tin wire
l Hot air gun
l Paper cutter
l Marker pen
Component
Figure C-18 shows the components of the straight SMB female connector and the coaxial cable.
C
D
E
F
D: Outer conductor of the coaxial E: Insulation layer of the coaxial F: Inner conductor of the coaxial
cable cable cable
Procedure
Step 1 For the coaxial cable made of different materials, peel the coaxial cable to expose its outer
conductor (D), insulation layer (E), and inner conductor (F) according to the lengths shown in
Figure C-19. The lengths of the reserved outer conductor, the reserved insulation layer, and the
exposed jacket are L1, L2, and L3 respectively, as listed in Table C-4.
L3
L2
L1
D
E
F
CAUTION
l When peeling the coaxial cable, do not damage the outer conductor or the shielded layer of
the coaxial cable.
l You can determine the length of the part to be peeled according to the length of the connector,
as shown in Figure C-20.
L2 L3
Cable Type External Diameter L1 (mm) (mm) (mm) Remarks
L1 L1
L2 L2
L3 L3
Step 2 Put a coaxial cable into press-fitting sleeve A, as shown in Figure C-21.
Step 3 Expand outer conductor D of the coaxial cable into a bell-mouthed shape as shown in Figure
C-22.
Step 4 Insert the inner conductor and the insulation part of the coaxial cable into plug B of the connector.
Wrap the outer conductor of the connector by using the outer conductor of the coaxial cable, as
shown in Figure C-23.
Step 5 Solder inner conductor F of the coaxial cable with the inner conductor of plug B, as shown in
Figure C-24.
B F
Welding
NOTE
After the welding, make sure that there is no metal wire (especially of the outer conductor) or redundant
soldering tin between the inner conductor and the outer conductor. Use the multimeter to test the insulation
state between the inner conductor and the outer conductor. Then, press-fit the outer conductor.
Step 6 Push press-fitting sleeve A towards the connector. Compact the outer conductor of the coaxial
cable. Press-fit sleeve A and the plug of the coaxial connector by using press-fitting tools, as
shown in Figure C-25.
----End
Follow-up Procedure
After assembling the cable components, install the components on devices, as shown in Figure
C-26.
C.5.2 Making the E1 Cable with the Straight SMB Male Connector
This topic describes how to make the E1 cable with the straight SMB male connector.
Recommended Tools
The recommended tools for making the E1 cable with the straight SMB male connector are as
follows:
l Wire stripper
l Wire crimping tool
l Diagonal pliers
l Wire clipper
l Electric soldering iron
l Tin wire
l Hot air gun
l Paper cutter
l Marker pen
Component
Figure C-27 shows the components of the straight SMB male connector and the coaxial cable.
D
E
F
D: Outer conductor of the coaxial E: Insulation layer of the coaxial F: Inner conductor of the coaxial
cable cable cable
Procedure
Step 1 For the coaxial cable made of different materials, peel the coaxial cable to expose its outer
conductor (D), insulation layer (E), and inner conductor (F) according to the lengths shown in
Figure C-28. The lengths of the reserved outer conductor, the reserved insulation layer, and the
exposed jacket are L1, L2, and L3 respectively, as listed in Table C-5.
CAUTION
l When peeling the coaxial cable, do not damage the outer conductor or the shielded layer of
the coaxial cable.
l You can determine the length of the part to be peeled according to the length of the connector,
as shown in Figure C-29.
L3
L2
L1
D
E
F
External L1 L3
Cable Type Diameter (mm) L2 (mm) (mm) Remarks
L1 L1
L2 L2
L3 L3
Step 2 Put a coaxial cable into press-fitting sleeve A, as shown in Figure C-30.
Step 3 Expand outer conductor D of the coaxial cable into a bell-mouthed shape as shown in Figure
C-31.
Step 4 Insert the inner conductor and insulation part of the coaxial cable into plug B of the connector.
Wrap outer conductor D of the connector by using the outer conductor of the coaxial cable, as
shown in Figure C-32.
Step 5 Solder inner conductor F of the coaxial cable with the inner conductor of plug B, as shown in
Figure C-33.
Welding
NOTE
After the welding, make sure that there is no metal wire (especially of the outer conductor) or redundant
soldering tin between the inner conductor and the outer conductor. Use the multimeter to test the insulation
state between the inner conductor and the outer conductor. Then, press-fit the outer conductor.
Step 6 Push press-fitting sleeve A towards the connector. Compact the outer conductor of the coaxial
cable. Press-fit sleeve A and the plug of the coaxial connector by using press-fitting tools, as
shown in Figure C-34.
----End
Follow-up Procedure
After assembling the cable components, install the components on devices, as shown in Figure
C-35.
C.5.3 Making the E1 Cable with the Bent SMB Female Connector
This topic describes how to make the E1 cable with the bent SMB female connector.
Recommended Tools
The recommended tools for making the E1 cable with the bent SMB female connector are as
follows:
l Wire stripper
l Wire crimping tool
l Diagonal pliers
l Wire clipper
l Electric soldering iron
l Tin wire
l Hot air gun
l Paper cutter
l Marker pen
Component
Figure C-36 shows the components of the bent SMB female connector and the coaxial cable.
E
F
G
Procedure
Step 1 For the coaxial cable made of different materials, peel the coaxial cable to expose its outer
conductor (E), insulation layer (F), and inner conductor (G) according to the lengths shown in
Figure C-37. The lengths of the reserved outer conductor, the reserved insulation layer, and the
exposed jacket are L1, L2, and L3 respectively, as listed in Table C-6.
L3
L2
L1
E
F
G
CAUTION
l When peeling the coaxial cable, do not damage the outer conductor or the shielded layer of
the coaxial cable.
l You can determine the length of the part to be peeled according to the length of the connector,
as shown in Figure C-38.
L1 L1
L2 L2
L3 L3
Step 2 Put a coaxial cable into press-fitting sleeve A, as shown in Figure C-39.
Step 3 Insert the inner conductor and the insulation part of the coaxial cable into plug C of the connector.
Wrap outer conductor E of the connector by using the outer conductor of the coaxial cable, as
shown in Figure C-40.
Step 4 Solder inner conductor G of the coaxial cable with the inner conductor of plug C, as shown in
Figure C-41.
Welding
NOTE
After the welding, make sure that there is no metal wire (especially of the outer conductor) or redundant
soldering tin between the inner conductor and the outer conductor. Use the multimeter to test the insulation
state between the inner conductor and the outer conductor. Then, press-fit the outer conductor.
Step 5 Push press-fitting sleeve A towards the connector. Compact the outer conductor of the coaxial
cable. Press-fit sleeve A and the plug of the coaxial connector by using press-fitting tools, as
shown in Figure C-42.
Step 6 Press-fit upper cover B on plug C of the connector, as shown in Figure C-43.
----End
Follow-up Procedure
After assembling the cable components, install the components on devices, as shown in Figure
C-44.
This topic describes how to install the internal components of the cabinet. The internal
component of the cabinet includes the subrack, board, and fan tray.
Ensure that the following materials and tools are available before installing and removing the
subrack.
D.1.2 Precautions
This topic describes the precautions for installing and removing the subrack.
Pay attention to the following points when installing or removing the subrack:
Procedure
Step 1 Wear the ESD wrist strap and connect its ground end to the ESD jack on the cabinet or wear
ESD gloves.
Step 3 Install captive nuts to the mounting rails of the cabinet according to the positions of the holes in
the mounting bracket.
Step 4 Place the subrack on the mapping cable troughs in the cabinet from the front of the cabinet.
Step 5 Confirm the installation position of the subrack in the cabinet. Install captive nuts to the mounting
rails of the cabinet based on the installation position of the subrack.
Step 6 Gently push the subrack into the cabinet until the brackets on the subrack are in contact with the
mounting rails of the cabinet. Align the eight holes in the mounting brackets with the captive
nuts in the mounting rail of the cabinet. Then, install the eight M6 x 12 panel screws to fasten
the subrack, as shown in Figure D-1.
CAUTION
When you fasten the screws, fasten them gently first, and then fasten them firmly in a diagonal
sequence.
----End
Procedure
Step 1 Wear ESD gloves or wear the ESD wrist strap and connect its ground end to the ESD jack on
the cabinet.
Step 2 Loosen the eight panel screws from the mounting brackets.
Step 3 Pull the subrack out along the cable troughs gently, as shown in Figure D-2.
----End
D.2.2 Precautions
This topic describes the precautions for installing and removing the board.
Pay attention to the following points when installing or removing the board:
l Ground the device according to the requirement.
l Wear ESD gloves or an ESD wrist strap correctly during the operation.
l Fasten the wrist strap around your wrist, and attach the other end of the wrist strap to the
ESD jacket of the device, as shown in Figure D-3.
l When the wrist strap is in the normal state, its resistance should range from 0.75 megohms
to 10 megohms. If the validity period (usually two years) of the wrist strap expires or the
resistance value does not meet the requirements, use a new ESD wrist strap.
l Do not touch boards with your clothes. Otherwise, the static electricity beyond the
protection scope of the wrist strap is generated.
l Wear the ESD wrist strap and place the board on an antistatic pad when replacing the board
or chip. Use antistatic tweezers or extraction tools to hold, insert, or remove the chip. Do
not touch chips, or circuits and pins on the printed circuit board (PCB) with bare hands.
l Keep the boards or components that are not installed in the ESD bags. Place the removed
boards or components onto an antistatic pad or other antistatic materials that are in the ESD
toolkit. Do not use non-antistatic materials, such as the white foams, common plastic bags,
or paper bags to pack the boards, or do not let them come in contact with the boards.
l Wear an ESD wrist strap when working on the ports of the boards because the ports are
also ESD sensitive. Discharge the static electricity of the cables and the protective sleeves
before connecting them to the ports.
l Store certain board packing materials (such as vacuum formed box and bags) in the room
for future use (recommended).
l Do not touch the surface of the PCB.
l When installing or removing a board, hold it firmly, and push or pull it gently.
l Insert the board (in the disconnected state) into or remove it from the slot carefully. Make
sure that the board does not collide with the subrack (chassis) or with the board in the
adjacent slot.
Procedure
Step 1 Wear the ESD wrist strap and connect its ground end to the ESD jack on the cabinet or wear
ESD gloves.
Step 2 Pull the ejector levers on the front panel of the board outwards. Hold the ejector levers with your
hands and insert the board gently along the board track until the ejector levers are clamped to
the top and bottom beams of the board cage.
Step 3 Press the ejector levers inwards and push the board into the subrack completely through the
acting force between the ejector levers and the subrack beam, until the ejector levers are parallel
with the front panel.
Step 4 Fasten the two screws on the front panel to fasten the board, as shown in Figure D-4.
----End
Procedure
Step 1 Wear ESD gloves or wear the ESD wrist strap and connect its ground end to the ESD jack on
the cabinet.
----End
Ensure that the following materials and tools are available before installing and removing the
fan tray.
l ESD gloves or ESD wrist strap
l Phillips screwdriver
l ESD bag
D.3.2 Precautions
This topic describes the precautions for installing and removing the fan tray.
Pay attention to the following points when installing or removing the fan tray:
l Take ESD measures before installing and removing the fan tray.
l When remove the fan tray, do not touch the fans when they are rotating.
l Remove or install the fan tray carefully and in a horizontal manner to prevent collision.
l Ensure that tools are positioned properly and the screws do not fall off accidentally during
the operation, because this may lead to a short circuit caused by metal.
Procedure
Step 1 Wear the ESD wrist strap and connect its ground end to the ESD jack on the cabinet or wear
ESD gloves.
Step 2 Push the fan tray into the service subrack along the guide rail, as shown in Figure D-6 (1).
Step 3 Fasten the screws on the front panel of the fan tray, as shown in Figure D-6 (2).
----End
Procedure
Step 1 Wear ESD gloves or wear the ESD wrist strap and connect its ground end to the ESD jack on
the cabinet.
Step 2 Loosen the screws from the front panel of the fan tray, as shown in Figure D-7 (1).
Step 3 Hold the handle on the front panel of the fan tray and disconnect the fan tray from the backplane
connector.
Step 4 After the fans stop rotating, pull the fan tray out gently from the service subrack along the guide
rail, as shown in Figure D-7 (2).
----End
E Cable Labels
This topic describes how to make, fill in, and attach the cable label.
Labels are attached to the cables to identify the physical positions of the cables on different
devices. There are two types of cable labels: labels for the power cables and labels for the signal
cables.
The cable labels can facilitate the cable connection and maintenance.
NOTE
This information must be stated in the self-check report to help the customer to maintain consistency in
labeling the cables of the devices in the telecommunications room.
Material Specification
The material features of the labels are as follows:
l Thickness: 0.09 mm.
l Color: Chalk white.
l Material: Polyester (PET).
l Applicable temperature: -29°C to +149°C.
l Compatible with laser printing or can be hand written by using oil markers.
l The material must pass the authentication of Underwriters Laboratories (UL) and Canadian
Standards Association (CSA).
Types
There are two types of cable labels: the label for the power cable and the label for the signal
cable.
84.0
7.5
7.0
5.5
5.5 Dotted line
11.0 10.0
11.0 TO:
1.5
Dividing line
Dividing line
0.6
5.5
5.5
7.0 1.0
7.5 Dotted line
37.0 2.0
Unit: mm
The dividing lines on the label specify the position of a cable. For example, there is a dividing
line between the cabinet number and the subrack number, and a dividing line between the subrack
number and the slot number. The size of the dividing line is 1.5 mm x 0.6 mm, and its color is
PANTONE 656c (light blue).
The dotted lines mark the position for folding the label when you attach it to the cable.
There is a mark "TO:" (upside down in the figure) at the lower right corner of the label. The
mark identifies the peer end of the cable to which the label is attached.
25
0.6
Label paper
1.5
Cable tie
100 0.6
Dividing line on the
label
Unit: mm
l Download the template from the technical support website "support.huawei.com". The path
is as follows: Related Links > Engineering Service > Engineering Quality > Quality
Standard and Template.
l Obtain the template from the Huawei local representative.
When using the Microsoft Word template, pay attention to the following requirements:
l You can modify the contents on the template according to the positions of the cables
installed on site. However, the settings of center, direction, and fonts of the characters on
the label cannot be changed.
l Generally, the size of the characters is not modified. When there are a lot of contents to be
filled in, change the font size of the characters. Make sure that the contents are clear and
legible.
1. Place the ordinary printed paper on the label paper. Compare and check whether the printed
paper conforms to the label requirement.
2. Make sure that the printing properties, such as Paper Size and Direction, are set correctly.
If the printed paper meets the requirements, print the required content on the label paper.
Otherwise, adjust the page setup and print the required content again until you obtain the
correct printout. To adjust the page setup, do as follows:
(1) Choose File > Page Setup.
(2) Select Layout, set Header and Footer to 0.
(3) Click the Margins tab. Select Left for Gutter Position. Adjust the values of Top,
Bottom, Left, and Right.
(4) If the dialog box as shown in Figure E-3, is displayed before printing, click Ignore
to continue the printing.
After adjusting the page setup, save the printing properties. This page setup is required only
when you use the template for the first time.
l All the contents should be printed on the label. Ensure that the content is not printed at the
bottom of the label page.
l The contents in the cells should be aligned to the center. In the case of a single-line printout,
the dividing lines and the "TO" mark should not be covered by the printed characters.
l If you merge the cells and print in multiple lines, adjust the contents and do not cover the
"TO" mark. Use the spacebar to move the content to the next line.
Writing Tool
To maintain the labels legible and neat, use the black oil marker (excluding the ball pen) delivered
with the products to write on the labels.
In special cases, you can use a black ballpoint pen, although it is not recommended to use a
ballpoint pen. The oil marker is more effective compared to the ballpoint pen. When you use
the marker pen to write on the labels, ensure that the surface of the labels is not oily. The oil can
smudge the letters.
NOTE
The delivered marker has two nibs. Use the smaller nib to write on the labels.
Font
The handwritten font must be similar to the standard typeface "Times New Roman" so that it is
clear and legible. Table E-1 lists the standard typeface.
0 1 2 3 4 5 6 7 8
9 A B C D E F G H
I J K L M N O P Q
R S T U V W X Y Z
The typeface for handwriting should be of proper size. When you fill in the label in Chinese
font, the size of the Chinese font must be proper, and the Chinese font must be legible and neat.
1 A01 2 A 06
06 A 1 A01 2
TO:
The contents on the signal cable are different from the contents on the power cable.
l Area 1 contains the location information about the cable end to which the label is to be
attached.
l Area 2 (with the "TO:" mark) contains the location information about the other end of the
cable.
l Area 3 is folded between area 1 and area 2.
Figure E-5 Printing parts on the label for the signal cables
Area 1
Area 3
Area 2 TO:
If the label is viewed from the cable leading-out area, it appears on the right side of the cable.
The side with "TO:" that faces outward indicates the peer end; the other side indicates the local
end. Therefore, the information in Area 1 at one end of the signal cable is the same as the
information in Area 2 at the other end of the cable.
l When you print, write, or attach labels, ensure that the labels are clean.
l Do not use ink-jet printers or ink pens to print or write on the labels because the label paper
is made up of moisture proof and waterproof material.
l Attach labels neatly. The new label is of striped type. The appearance of the product is
affected if the attaching position or direction is not correct.
l Bundle the cable ties at the same height, and place all identification plates in the same
direction.
l The positions of "up", "down", "right", and "left" in this topic (excluding the description
of printer setting) are viewed when you face the labels.
Figure E-6 Attaching the label to the signal cable at a proper position
TO:
TO:
1 A01 2
1 A01 2 A 06
A 06
Figure E-7 shows how to attach the label to the signal cable.
2-3 mm
TO:
1 A01 2 A 06
TO:
B03 -48V2
B03
TO:
-48V2
Cable
The external alarm cables are connected to the first cabinet that provides power supply of each
row. Labels attached to the first cabinet must indicate the access terminal distribution for the
devices. Labels are not required to be attached to the device unless it is required. Here, only Area
2 of the label should be filled in.
Table E-2 describes the information on the label for the external alarm cable.
Table E-2 Information on the label for the external alarm cable
NOTE
Generally, the preceding numbering method helps identify the position of a specific cabinet. If two cabinets
are installed back to back, the front direction of the cabinet must be specified. Hence, the numbering method
MNO is used. "O" indicates the direction of the cabinet, which can either be "A" or "B." This numbering
method is also used for the cable labels described in the following sections.
You need to fill only a part of the text area because the label on the alarm cable provides basic
information. It is recommended you reserve the entire length of the label. Do not cut off the
blank area.
Figure E-9 shows a label on the alarm cable. "A01" indicates that the alarm cable is connected
from the first cabinet to the cabinet in row A, column 01.
A01
TO:
Application
The labels for the network cables are attached to the network cables that connect to the boards,
or the labels for the network cables are attached to the cables that connect to the hubs, servers
or agents of the value added service (VAS) devices.
C: Slot The slots are numbered from top to bottom and from left to
number right. 01 indicates slot 1 of the subrack.
D: Network The ports are numbered from top to bottom and from left to
port number right. 01 indicates the first network port.
Z: Position of You can fill the number that indicates the position of the
the terminal terminal device according to actual conditions.
device l For the router connected to the cabinet, specify the cabinet
number, subrack number, and network port number of the
router, such as B02-03-12.
l For the NMS workstation, specify the specific location.
For the network cables that connect to the hubs, servers, or agents of the VAS devices, the
information on the labels is provided according to the actual conditions.
l For the cable from the hub to the server, specify the cabinet number and subrack number
where the hub is located, and specify the serial number on the hub. Specify the cabinet
number and subrack number where the server is located. For a stand-alone server, specify
the specific position of the server.
l For the cable from the hub to the agent, specify the serial number of the network port on
the agent end. The cabinet number and the subrack number should be the same as the cabinet
number and the subrack number described in Table E-3.
l For a stand-alone hub that is not installed in any subrack or cabinet, specify its recognizable
position.
Specify the serial number on the hub, the network port number of the agent and the position of
the stand-alone server according to the actual conditions.
A01-03-10-05
B02-03-12
TO:
l "A01-03-10-05" indicates that one end of the network cable is connected to Ethernet port
05, slot 10, subrack 03 of the cabinet in row A, column 01.
l "B02-03-12" indicates that the other end of the network cable is connected to Ethernet port
12, subrack 03 of the cabinet in row B, column 02. The slot number is not specified.
Table E-4 Information on the label for the optical fiber connecting two cabinets
Content Meaning Example
MN-B-C-D-R/ MN: Cabinet number A01 indicates the first cabinet in row A.
T
B: Subrack number The subracks are numbered from bottom to
top. 01 indicates the lowest subrack.
R: Optical receiving -
interface
T: Optical transmitting
interface
R: Optical receiving
interface
T: Optical transmitting
interface
Figure E-11 Example of the label on the optical fiber connecting two cabinets
A01 01 05 05 R
G01 01 01 01 T
TO:
l "A01-01-05-05-R" indicates that one end of the optical fiber is connected to the optical
receiving interface 05 in slot 05, subrack 01 in the cabinet in row A, column 01.
l "G01-01-01-01-T" indicates that the other end of the optical fiber is connected to optical
transmitting interface 01 in slot 01, subrack 01 in the cabinet in row G, column 01.
Meaning of the Label for Optical Fiber Connecting the Cabinet to the ODF
Table E-5 describes the information on the label for the optical fiber connecting the cabinet to
the ODF.
Table E-5 Information on the label for the optical fiber connecting the cabinet to the ODF
Content Meaning Example
MN-B-C-D-R/T MN: Cabinet number A01 indicates the first cabinet in row A.
R: Optical receiving -
interface; T: Optical
transmitting interface
ODF-MN-B-C-R/ MN: ODF row and ODF M: numbered A to Z from front to back in
T column. each row.
N: numbered 01 to 99 from left to right.
G01: ODF in row G and column 01.
R: Optical receiving -
interface
T: Optical transmitting
interface
Example of the Label on the Optical Fiber Connecting the Cabinet to the ODF
Figure E-12 shows the label on the optical fiber connecting the cabinet to the ODF.
Figure E-12 Example of the label on the optical fiber connecting the cabinet to the ODF
ODF G01 01 01 R
T 05 05 01 A01
TO:
l "ODF-G01-01-01-R" indicates that one end of the optical fiber is connected to the optical
receiving terminal in row 01, column 01 of the ODF in row G, column 01.
l "A01-01-05-05-T" indicates that the other end of the optical fiber is connected to optical
receiving interface 05 in slot 05, subrack 01 in the cabinet in row A, column 01.
There are two types of labels that are used for trunk cables:
l One type of the label is used for the trunk cable connecting two cabinets, such as the label
for the trunk cable from the trunk board to the built-in transmission unit and the label for
the trunk cable from the trunk board to the trunk board. The labels are attached to both ends
of the trunk cable to identify the position of the cable on the cabinet or the trunk board.
l The other type of the label is used for connecting the cabinet and the DDF. The labels are
attached to both ends of the trunk cable to identify the positions of the cable on the cabinet
and the DDF.
The trunk cables include 75-ohm E1 cable, 120-ohm E1 cable, 100-ohm T1 cable, 120-to-75-
ohm trunk cable, 34 Mbit/s cable, 45 Mbit/s cable, 140 Mbit/s cable, 155 Mbit/s cable, and clock
cable.
Table E-6 Information on the labels for the trunk cable connecting two cabinets
Content Meaning Example
C: Slot number The slots are numbered from left to right, from top
to bottom. 01 indicates slot 1 of the subrack.
D: Cable number The cables are numbered from left to right, from top
to bottom. 12 indicates the 12th trunk cable.
R: Optical -
receiving
interface; T:
Optical
transmitting
interface
C: Slot number The slots are numbered from left to right, from top
to bottom. 01 indicates slot 1 of the subrack.
D: Cable number The cables are numbered from left to right, from top
to bottom. 12 indicates the 12th trunk cable.
R: Optical -
receiving
interface; T:
Optical
transmitting
interface
Figure E-13 Labels for the trunk cable connecting two cabinets
G01 01 05 12 T
D02 01 01 01 R
TO:
l "G01-01-05-12-T" indicates that one end of the trunk cable is connected to the transmitting
terminal of trunk cable 12 on slot 05, subrack 01 in the cabinet in row G, column 01.
l "D02-01-01-10-R" indicates that the other end of the trunk cable is connected to the
receiving terminal of trunk cable 10 on slot 01, subrack 01 in cabinet in row D, column 02.
Meaning of the Label for Trunk Cable Connecting the Cabinet to the DDF
Table E-7 describes the information on both sides of the labels for the trunk cable connecting
the cabinet to the DDF.
Table E-7 Information on labels for the trunk cable connecting the cabinet to the DDF
C: Slot number The slots are numbered from left to right, from top to
bottom. 01 indicates slot 1 of the subrack.
D: Cable number The cables are numbered from left to right, from top
to bottom. 05 indicates the fifth network port.
R: Optical -
receiving
interface; T:
Optical
transmitting
interface
C: Column number
of the terminal
Example of the Label for Trunk Cable Connecting the Cabinet to the DDF
Figure E-14 shows the information on both sides of the label for the trunk cable connecting the
cabinet and the DDF.
Figure E-14 Example of the label on the trunk cable connecting the cabinet to the DDF
A01 03 01 01 T
AR 01 DDF G01 01
TO:
l "A01-03-01-01-R" indicates that one end of the trunk cable is connected to the receiving
terminal of trunk cable 01 in slot 01, subrack 03 of the cabinet in row A, column 01.
l "DDF-G01-01-01-AR" indicates that the other end of the trunk cable is connected to the
receiving terminal of direction A (connected to optical network device) in row 01, column
01 of the DDF in row G and column 01.
The labels are attached to both ends of the subscriber cable to identify the positions of the cable
on the cabinet and the MDF.
MN-B-C-D MN: Cabinet number A01 indicates the first cabinet in row A.
A01 03 01 01
MDF G01 01 01
TO:
l "A01-03-01-01" indicates that the local end of the subscriber cable is connected to terminal
01 in slot 01, subrack 03 of the cabinet in row A, column 01.
l "MDF-G01-01-01" indicates that the peer end of the subscriber cable is connected to the
terminal in row 01, column 01 of the MDF in row G, column 01.
The label indicates only the location of the peer end, control cabinet or distribution box.
Information about the local end is not required. Table E-9 lists the information about the two
inputs of the -48 V power supply on the label. The information about other DC voltages (such
as 24 V, 60 V) should be written in a similar way. Make sure that the labels are attached in the
correct direction. After the cable ties are bundled on to the cable, the identification plates with
the labels should point upward.
The contents on the cable labels in the same cabinet should be in the same direction, as shown
in Figure E-16.
TO:
A01 -48V2
B08
TO:
B03 -48V2
l On the loaded cabinet side, the label marked as "A01/B08- -48 V2" indicates that the cable
is used for the -48 V2 DC supply. The cable is routed from the 8th connector in row B of
the -48 V busbar in the power distribution cabinet in row A, column 01.
l On the power distribution cabinet side, the label marked as "B03- -48 V2" indicates that
the cable is used for the -48 V2 DC supply. The cable is routed from the loaded cabinet in
row B, column 03.
l In the power distribution cabinet (or the first power cabinet of a row in the transmission
telecommunications room), each terminal on the -48 V connector bar has a numeric
identification. For example, such as "08" (also mentioned as "8") in the label "A01/B08-
-48 V2."
l The PGND and the BGND are two copper bars. The terminals are directly connected to
these copper bars. Therefore, the connection of any of the terminal does not affect the
distribution of the power supply. Only the row and column numbers of the power
distribution cabinet are required. For example, if the label on the loaded cabinet side is
"A01-BGND", the power cable is a BGND cable that is connected to the BGND copper
bar in the power distribution cabinet in row A, column 01. The information on the labels
for the PGND cables must be provided in the similar way.
MN-AC MN: Cabinet number or the power socket position. Power socket: Mark the
positions clearly to avoid confusion. If the sockets have multiple rows and
columns, identify their positions as the cabinet.
The label only indicates the location of the peer end or socket. Information about the local end
is not required. Ensure that the labels are attached in the correct direction. After the cable ties
are bundled onto the cable, the identification plates with the labels must point upward, as shown
in Figure E-17.
TO: TO:
A01 AC B01 AC
Label on the loaded cabinet side (position of the Label on the power distribution cabinet side
cable on the power distribution cabinet side) (position of the cable on the loaded cabinet side)
l On the loaded cabinet side, the label marked as "A01-AC" indicates that the cable is routed
from the power socket in row A and column 01.
l On the power distribution cabinet side, the label marked as "B01-AC" indicates that the
cable is routed from the loaded cabinet in row B and column 01.
F Environment Requirements
Climatic Requirements
Table F-1 lists the climatic requirements.
Item Range
Waterproof Requirements
Storage requirements of the on-site device are as follows:
l Place the device indoors.
l There should be no water on the ground.
l Water should not flow into the package.
l Store the device away from the places where it may be exposed to leakage from automatic
fire fighting devices or heaters may occur.
Air Cleanness
l There must be no explosive, conductive, magneto-conductive or corrosive dust.
l The density of mechanically active materials in the air must comply with the restrictions
listed in Table F-2.
Table F-2 Restrictions on the density of mechanically active materials in the air for storage
l The density of chemically active materials in the air must comply with the restrictions listed
in Table F-3.
Table F-3 Restrictions on the density of chemically active materials in the air for storage
H 2S ≤ 0.10 mg/m3
HF ≤ 0.01 mg/m3
O3 ≤ 0.05 mg/m3
Mechanical Stress
The mechanical stress imposed on the device that is stored must comply with the restrictions
listed in Table F-4.
Table F-4 Restrictions on mechanical stress imposed on the device that is stored
Climatic Requirements
Table F-5 lists the climatic requirements.
Item Range
Waterproof Requirements
During the transportation, the following conditions must be met:
l Store the package in good condition.
l Take waterproof measures to prevent rain from entering the package.
l There should not be any water on the device when it is transported.
Air Cleanness
l There must be no explosive, conductive, magneto-conductive or corrosive dust.
l The density of mechanically active materials in the air must comply with the restrictions
listed in Table F-6.
Table F-6 Restrictions on the density of mechanically active materials in the air for
transportation
Mechanically Active Material Restriction
l The density of chemically active materials in the air must comply with the restrictions listed
in Table F-7.
Table F-7 Restrictions on the density of chemically active materials in the air for transportation
Chemically Active Material Restriction
H 2S ≤ 0.10 mg/m³
HF ≤ 0.01 mg/m³
O3 ≤ 0.05 mg/m³
Mechanical Stress
The mechanical stress imposed on the device that is transported must comply with the restrictions
listed in Table F-8.
Table F-8 Restrictions on the mechanical stress imposed on the device that is transported
Item Sub-item Range
Climate
Table F-9 lists the climatic requirements.
Item Range
Air Cleanness
l There is no explosive, conductive, magneto-conductive or corrosive dust.
l The density of mechanically active materials in the air should comply with the restrictions
stated in Table F-10.
Table F-10 Restrictions on the density of mechanically active materials in the air for storage
l The density of chemically active materials in the air should comply with the restrictions
stated in Table F-11.
Table F-11 Restrictions on the density of chemically active materials in the air for storage
H 2S ≤ 0.03 mg/m³
Mechanical Stress
Table F-12 lists the requirements on mechanical stress.
Table F-12 Requirements on mechanical stress imposed on the device that is stored
Item Sub-item Range
Static load 0
Electromagnetic Environment
Table F-13 lists the requirements on the electromagnetic environment.
Capital l Use the reinforced concrete structure for the construction of the
construction telecommunications room.
l Install the lightning proof device in the telecommunications room.
l The lightning proof ground must share the same ground body with
the protection grounding of the telecommunications room.
AC power l Use a special power transformer for the telecom offices. Use the metal
requirements jacket or steel tube to cover the power cables before burying them
under the ground. Ground both ends of the metal jacket or steel tube
nearby and properly. Bury the cable under the ground. The length
underground should not be less than 15 m.
l Use a TN-S power supply system for the telecom offices. The socket
that supplies power to box-type products should be a uniphase triplex
socket. Make sure that the contact holes of PE cables (PGND cable)
in the socket can provide reliable protection grounding for power-
demanding device and maintenance terminal. Install a gapless zinc
oxide arrester to each of the three phase lines on the low tension side
of the AC power transformer. Ground the enclosure of the
transformer, the neutral lines on the low tension side, and the metal
steel tubes of the power cables that connect to the enclosure of the
transformer correctly and close to each other.
Power cables l Do not lead the AC/DC power cables in and out of the
leading in the communications site in the aerial mode.
communications l After the low-voltage power cables are led into the telecommunica-
site be equipped tions room, install the lightning protection box for the power cables
with the lightning in the AC voltage stabilizer and the AC power distribution panel
protection box (unit). Ground the arrester correctly and close to the unit.
l For the telecommunications room built in the cities, install the power
supply arrester with the nominal discharging current of not less than
20 kA.
l For the telecommunications room built in the suburbs, where
lightning strikes occur, install the power supply arrester with the
nominal discharging current that is larger than 60 kA.
l For the telecommunications room in the mountain areas, where
lightning strikes occur, or in separate high-rise buildings in the city,
install the power supply arrester with the nominal discharging current
that is larger than 100 kA.
l The ground cable of the lightning protection box should be shorter
than 1 m.
Grounding of DC l Connect the DC working ground (positive pole of the –48 VDC
power distribution power supply or the negative pole of the 24 VDC power supply) to
the nearest indoor collective ground cable. The total ground cable
should meet the maximum load of the device.
l The power device must have the DC working ground cable, which
can connect the power device to the collective ground cable.
General l Do not connect the neutral line of the AC power cable to the
Requirements on protection ground of any telecom device in the telecommunications
grounding room.
l Ground cables should meet the maximum payload requirement of the
device.
l Do not install the fuse or switch on the ground cable.
l Ensure that all ground cables are as short as possible, and arrange
them as straight as possible. No oxidation corrosion should occur in
the general ground bar. Otherwise, ground bar cannot connect
properly to the ground cables, which results in the increase of contact
resistance on the ground path. Make sure that the ground cables are
connected reliably to the ground bar in the telecommunications room.
Grounding l The ground resistance of the grounding system should be less than
resistance 10 ohms.
l Keep the upper end of the ground body at least 0.7 meters over the
ground. In cold areas, bury the ground body below the frozen ground.
l Measure the ground resistance periodically (monthly) to ensure the
effective grounding.
Subscriber cables l The external subscriber cable must be led into the site under the
and MDF ground.
l The metal jacket of the cable should be grounded in the distribution
frame.
l The MDF must be equipped with a protective unit.
l Perform spot test on the protective unit periodically (every 2 years)
according to relevant standards and replace the disabled or degraded
protective units in time.
Routing of signal l Do not arrange the signal cables overhead in the telecommunications
cables room. All signal cables must be led into the site under the ground.
l The metal jackets of all cables led into the telecommunications room
should be grounded in the distribution frame or connected to the
protection ground bar in the telecommunications room.
l After signal cables are led into the device, relevant signal lightning
protection boxes should be installed for the corresponding ports on
the device.
l Ensure that the ground cable of the lightning protection box is as short
as possible.
l The idle line pair of the signal cable from or to the office should be
grounded in the telecommunications room.
Collective ground l Use the ground ring or ground bar for the collective ground cable.
cable l Do not use aluminum cables as ground cables. Take measures to
prevent electrification corrosion when connecting different metal
parts together.
l Use the copper busbar as the collective ground cable with the cross-
sectional area of not less than 120 mm², or use the galvanized flat
steel that has the same resistance.
Grounding lead-in Use the galvanized flat steel with cross-sectional area of 40 mm x 4 mm
cable or 50 mm x 5 mm.
l The conducting wire is fire-resistant. Route the conducting wire according to the local
regulations, and set the low-voltage power distribution room also according to the local
regulations.
Table F-16 lists the specifications for the DC power supply.
DC power capacity to support the Greater than 1.5 times of the rated current at least
surge current
Overshoot amplitude of switch Not more than ±5% of the integral value of the DC output
on/off voltage
Dynamic response The recovery time is less than 200 ms. The overshoot is
in the range of the integral value of the DC output voltage
±5%.