User Manual V 1.1
User Manual V 1.1
V 1.1
1
Introduction
LightShark series is a new concept within the lighting control systems that
adapts to the daily needs, offering a powerful, compact and economical solution.
Perfect for small shows, nightclubs, school theaters, corporate events and
medium-size live shows.
Our Hardware and Software departments have worked hard to offer you a
simple, powerful and compact lighting system. From WORK PRO we hope it
meet all your expectations.
2
All LightShark devices have a built-in WiFi access point, so they can be operated
from any smartphone, labtop or tablet.
Thanks to its compact size, LightShark can be carried along with your tablet
backpack (LS-Core) or as hand luggage (LS-1). Both devices have the same
features.
All devices have the LightShark software inside, allowing to be operated from
any tablet, PC or smartphone… whatever the Operating el System or version.
No drivers are required, ¡LightShark is Plug&Play!
To use LightShark you will only need to connect to the WiFi network created by
the devices and go to lightshark.work on your web browser.
3
En aquellas situaciones en las que no sea posible conectarse a lightShark utilizando WiFi ( interferencias,
inhibidores.. ) es posible conectarse directamente a los dispositivos a través de una r ed cableada a través del
The LightShark software is always running inside the console (LS-Core or LS-1),
puerto de conexión
in the de red de cada
WiFi connection dispositivo.
between your device and the console only travels user
interface data, never DMX data.
En aquellas situaciones en las que no sea posible conectarse a lightShark utilizando WiFi ( interferencias,
Since in the WiFi connection only travels user interface data, the console
inhibidores.. ) es posible
continues conectarse
operating even ifdirectamente a los dispositivos
the WiFi connection fails. aWhen
travésitdeisuna
notr ed cableada
possible toa través del
puerto de conexión
connect de red de cada
to LightShark via WiFi (interferences, inhibitors…) it ca be done using a
dispositivo.
wired connection through the Ethernet port on the equipment.
4
It is posible to simultaneously connect up to 3 devices to LightShark, showing
different windows on each device. This allows the user to create a multi-screen
system.
5
Contents
1. INFORMATION ...................................................................................................... 8
2. DEVICES ............................................................................................................... 9
LS-1 .................................................................................................................... 10
LS-Core ............................................................................................................... 12
Connectivity ........................................................................................................ 13
3. USER INTERFACE............................................................................................... 18
Palettes ............................................................................................................... 18
Virtual Playback ................................................................................................... 28
Cuelist ................................................................................................................. 30
Executors ............................................................................................................ 32
Prog/Out.............................................................................................................. 33
4. CREATING AND SAVING SHOWS ...................................................................... 34
Creating a new show ........................................................................................... 34
Loading an existing show .................................................................................... 34
Saving a show ..................................................................................................... 34
Exporting a show................................................................................................. 34
5. ADDING FIXTURES TO A SHOW ........................................................................ 35
Adding fixtures to the show ................................................................................. 35
Advanced patch .................................................................................................. 35
Modifying the address on an already patched fixture .......................................... 36
Removing a fixture from the Patch ...................................................................... 36
Inverting Pan and Tilt ........................................................................................... 36
Updating the libraries .......................................................................................... 37
Copying libraries between consoles .................................................................... 37
6. FIXTURE SELECTION.......................................................................................... 38
Fixture selection .................................................................................................. 38
Creating fixture groups ........................................................................................ 39
Renaming fixture groups ..................................................................................... 39
Removing fixture groups ..................................................................................... 39
Moving fixture groups.......................................................................................... 39
7. RECORDING SCENES ........................................................................................ 40
Cuelist ................................................................................................................. 40
Recording a Cuelist ............................................................................................. 40
Modifying Cues ................................................................................................... 41
8. USING FX ............................................................................................................ 42
9. SCENE PLAYBACK ............................................................................................. 44
6
Playback options ................................................................................................. 44
Cuelist options .................................................................................................... 47
10. USE OF EXECUTORS ...................................................................................... 49
Add Cuelist .......................................................................................................... 51
Empty a box ........................................................................................................ 51
7
1. INFORMATION
Equipson SA 2018. All rights reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted or translated into any language in any form or by any means without the express
written permission of Equipson S.A.
Product warranty or service will not be extended if: (1) the product is repaired, modified or
altered, unless such repair, modification of alteration is authorized in writing by Equipson S.A.;
or (2) the serial number of the product is defaced or missing.
EQUIPSON S.A. PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. IN NO EVENT SHALL EQUIPSON S.A., ITS DIRECTORS, OFFICERS, EMPLOYEES
OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF
USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF EQUIPSON S.A. HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR
ERROR IN THIS MANUAL OR PRODUCT.
Products and corporate names appearing in this manual may or may not be registered
trademarks or copyrights of their respective companies, and are only used for identification or
explanation and to the owners’ benefit, without intent to infringe.
And the rules of EMC EN55022: 2010 EN61000-3-3: 2013 EN55020:2007+ A11 EN61000-4-2:
2009 EN61000-4-3: 2006 + A1+ A2
ATTENTION: Any modification or changes made to this device, unless explicitly approved by
Equipson S.A., will invalidate the authorisation of this device.
NOTE: This equipment has been tested and found to comply within the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
For further details please contact: Equipson SA, AV El Saler nº14, Silla, Valencia, España.
Telephone: +34 961 216 301 e-mail: [email protected]
8
2. DEVICES
LightShark series range comprises two independent devices:
LS-1 is a new generation of web-based lighting consoles, designed for all types of
shows. It provides a simple, powerful and portable multiplatform control system.
LS-Core is focused on those technicians who need the features of a complete lighting
console reducing the space to the minimum. Thanks to its internal task scheduler it is
an excellent solution for fixed installations.
-30 Pages.
-Fan function.
-Numeric keypad.
-Built-in FX engine.
-Multi-Touch UI.
-Quick Patching.
-User Palettes.
9
LS-1
1- Grand Master
2- Blackout
3- Page selection
4- Editor
5- Selection buttons
6- Go buttons
7- Playback Area
8- Flash buttons
9- Encoders
10
1- Desk Lamp (5V)
5- WiFi Antenna
6- Power Switch
7- Power Socket
Weight: 3,7kg
11
LS-Core
2- Navigation buttons
3- WiFi Antenna
4- Information display
7- Power Socket
Weight: 460g
12
Connectivity
In order to perform all its functionalities on any computer, tablet and smartphone with
a Web Browser, LightShark features an integrated Web Server. You will only have to
connect to the WiFi access point of the LS-1 or LS-Core. As an alternative, you can
connect via an existing WiFi network or use the Ethernet port of the LS-1 or LS-Core
for a wired connection.
To connect to the WiFi access point of LightShark with your computer, tablet or
smartphone:
1 Check that the WiFi antenna is properly connected to the LightShark device,
plug the external power supply and turn on the device. The LCD display of the
device will light up, please wait until the device has started completely.
13
3 Start the Web Browser of your device and type lightshark.work in the URL
field, or 192.168.42.1 The LightShark loading screen will appear and you will be
redirected to the Palette window.
14
WARNING
The first time you connect is important that you change the WiFi password. Go to the
main menu on LightShark (on the top-left side of the screen) and click on the settings
icon and select the “NETWORK” tab to proceed with the required changes.
NOTE
LightShark can run in full screen, hiding the navigation bar of the Web Browser, and it
can be launched as any other app.
1 Once connected to LightShark, press the Share button and the option “Add to Home
Screen”.
15
2 Press “Add”.
3 A LightShark icon will appear in the Home screen, so you can directly access to
LightShark without having to open the Web Browser.
16
4 Now LightShark will open in full screen mode.
17
3. USER INTERFACE
LightShark has a simple but complete User Interface. It is possible to control all the
device parameters, to record scenes and to run the shows. The interface consists of 5
different views and a main menu access:
Palettes
It is LightSharsk´s main view. From this window the user can select and control the
fixtures, and also record scenes or edit elements. The Palette Window is divided into
three sections:
1- Fixture Selection Area, where the user can select the desired fixtures through Groups,
the numeric keypad or individually.
18
2- Attribute Control Area, which is divided into 7 sections. Depending on the kind of
fixture and the type of attribute it will display different information:
19
On the parameters view the user will find all the attributes for the selected type. The
attributes are automatically shown in groups of 4. In case the selected section has for
example 7 “BEAM” channels, you may access to the next 3 attributes by scrolling down.
20
LS-1 users may interact with the interface using the encoders and buttons, so each LS-
1 encoder controls one of the attributes displayed (the top parameter is controlled by
the first encoder on the left, and so on).
The information shown in this area is also shown on the LCD integrated screen of the
LS-1. It is possible to move between attributes using the physical attribute buttons on
the console, or scrolling on the interface.
Each attribute has its own palettes. Some boxes will show the palettes defined by the
libraries. On the remaining boxes the user may record his own palettes.
In the Position and Colour attributes, it is possible to see a third view as well as
“PARAMETERS” and “PALETTES”. The Colour Picker (colour) view and the coords
(Position) view.
21
22
LightShark includes an internal FX generator, so it is possible to add an effect to one
or several fixtures.
LightShark arranges the effects into 4 categories: Position, Colour, Beam and Intensity.
Each category may have up to 9 different effects.
3-Editor Area, which allows the user to perform editing and recording functions.
23
4-Playback Area, which allows the user to play the show, run the Cuelist and control
the output level.
The GrandMaster is minimised by default, just press on the button to extend it and show
the fader. Pressing again, it will minimise again.
It is possible to add a specific level to the GrandMaster pressing for 2 seconds the
value field.
Through Playbacks, LightShark allows to play all the stored information in the show.
LightShark holds up to 30 Playbacks per page. The main 10 Playbacks are next to the
UI of the software, while the other 20 are displayed when sliding with the finger
horizontally on the Playbacks area.
These 20 Playbacks, accessible through the sliding movement (or from the “Virtual
Playbacks” view) behave as Wings.
24
LighShark allows to control the Playbacks using:
MIDI: in order to execute or adjust the level, any part (Fader, Encoder, Key) can
be mapped from a Playback to a MIDI controller.
The control area is configured to control the first 10 Playbacks, no matter which of the
3 Playback blocks is selected. This means that even when sliding the finger to access
the 11-20 groups of Playbacks, the control will still work on the first 10 Playbacks.
Playbacks are always minimized. If you want to access all the control functions of the
Playback, you may press on the fader level intensity indicator to maximize it.
When maximizing the Playback, all the elements on zones 1, 2 and 3 are blocked. To
be able to access them again, the Playback must be minimized.
25
By holding down the value field for 2 seconds, you may give the Playback an specific
value.
It is possible to configure some options that determine how the Playback and the
elements that form it work. The Playback priority, the way it reproduces, the control
functions of the FX,... can be established.
26
To hide the Playback Options menu, you may press the top-left arrow on the panel.
27
Virtual Playback
From the “Virtual Playback” view the user may access the Playbacks. This can be very
helpful when using the LS-Core or when a physical control device is not available.
Empty: when no Cuelist is assigned, it shows in Grey. This is how all the
Playbacks are when starting a show from the very beginning.
The pages allow the user to predefine some Cuelist presetting using the Playbacks, so
they can be quickly loaded at any time.
28
LightShark supports up to 30 Playback pages, allowing physical and virtual faders to
have different functions and behaviours depending on the page they are located.
Usually a page per song is used.
Using the UP and DOWN keys you may navigate through the pages. The tag showing
the actual page is located between the keys.
29
Cuelist
LightShark has a Cue and Cuelist storage where the user may navigate through all the
Cues and Cuelist stored (additional information ahead). From the Playbacks is possible
to directly access the associated Cuelist double clicking on the Playback information
field.
Pressing on the information field the CUES Window appear, showing the Cuelist
associated to that Playback:
At the left-side the user may find all the Cuelist in the show. Selecting a Cuelist will show
the information that it includes (Cues, times,...). Pressing on the left-side arrow, it is
possible to see the information that this particular Cue includes.
30
When accessing the information of the Cue, LightShark will show the values that were
recorded.
31
Executors
The “Execute” Window is a user-configurable special window, in which the Cuelists may
be added and their behaviour configured.
32
Prog/Out
From this window it is possible to see the progammer information.
The devices will be sorted according to the inclusion order. The information shown in
this window will be the information added to the Cue at that very moment.
33
4. CREATING AND SAVING SHOWS
LighShark includes a file manager to load, copy, save, delete and rename files.
To create a new show from scratch, please access the LightShark menu from the icon
on the top-right and press “NEW”.
1 Access the LightShark menu through the icon on the top-right and press
“LOAD”.
2 LightShark will open the file manager where all the stored files on the console
can be found. “Double click” on the show you want to execute.
Saving a show
1 Access the LightShark menu through the icon on the top-right and press
“SAVE”.
2 LightShark will show a keyboard on the display to enter the show name. If you
want to overwrite a file, simply press “OK”.
Exporting a show
1 Access the LightShark menu through the icon on the top-left, press “File
Manager” and select the top tab “Shows”.
2 Select the show you want to export and press “Export”. LightShark will copy
the show file in the USB external memory.
34
5. ADDING FIXTURES TO A SHOW
LightShark assigns an ID to each of the patched fixtures, allowing them to be selected
through the keyboard. In addition, it gives them a name, so they can also be easily
found.
LightShark allows all kind of fixtures to be treated the same way. This is possible
because the information is saved in a generic way, not on specific DMX values. So if
the user has created a Cue with a particular colour, LightShark can apply this
information to any other fixture (which obviously has that attribute) and get a similar
colour, no matter that the colour attributes on the different fixtures are located on
different channels.
LightShark includes its own fixture library and a selection of generic libraries for those
devices of common use (dimmers, fog machines, Led Pars,...). There can be found in
the “Generic” folder. The libraries created by the user are saved in the “User” folder.
1 Access the LightShark menu through the icon on the top-left, press the patch
key and select the top tab “Add Fixtures”.
2 Select a manufacturer, a model and a fixture mode. As you may see, the
manufacturers and fixture models are in alphabetical order, making easier the
access and the search.
3 Enter the number of fixtures you want to add and press “Patch”. The fixtures
will be added from the first DMX channel available on.
Advanced patch
1 Access the LightShark menu through the icon on the top-left, press the patch
key and select the top tab “Add Fixtures”.
2 Select a manufacturer, a model and a fixture mode. As you may see, the
manufacturers and fixture models are in alphabetical order, making easier the
access and the search.
3 Enter the number of fixtures you want to add and activate “Advanced” to add
the fixtures on an expecific address:
35
screen keyboard will be displayed, where you can directly enter the
universe number.
Through the “Start Channel” field the user may adjust the address of the
starting DMX channel where the fixture (or fixture group) will be added.
Please note that the channel can be adjusted either using the + and -
keys, or through the keyboard holding down on the number field.
The “Offset” field may be used to define the number of empty channels
between each fixture. Please note that the channel can be adjusted either
using the + and - keys, or through the keyboard holding down on the
number field.
1 Access the LightShark menu through the icon on the top-left, press the patch
key and select the top tab “Patched”.
3 Press the “REPATCH” key. On the side menu a panel will prompt where the
user may write the new DMX address.
4 Adjust the new address of the fixture and press the “PATCH” key.
1 Access the LightShark menu through the icon on the top-left, press the patch
key and select the top tab “Patched”.
1 Access the LightShark menu through the icon on the top-left, press the patch
key and select the top tab “Patched”.
2 Press the “P” or “T” key if you want to invert the Pan or Tilt. In some situations,
you might need to press the “S” key to swap the Pan for the Tilt.
36
Updating the libraries
Every LightShark update automatically includes the latest library version. If the user
wants to update the libraries without updating LightShark, the library file can be
downloaded from the LS-Cloud, and it can be copied into a USB memory stick. Then,
from LightShark, follow these steps:
1 Access the LightShark menu through the icon on the top-left, press the “File
manager” key and select the “USB” top tab.
2 Select the library files and press the “Import” key. LightShark will ask if you
want to replace the fixture library. Press “OK”.
When updating the library, all the manufacturers folders will be replaced by the new
version. All except the “User” folder, which will remain the same.
1 Access the LightShark menu through the icon on the top-left, press the “File
manager” key and select the “Brands” top tab.
2 Select the manufacturer with the libraries you want to export and press the
“Export” key. LightShark will copy the manufacture`s folder with all its fixtures,
icons and resources into the external USB memory stick.
3 Connect the USB memory stick into the console in which you want to import
the libraries and access the LightShark menu through the icon on the top-left.
Press the “File manager” key and select the “USB” top tab.
4 Select the library files and press the “Import” key. LightShark will ask if you
want to replace the fixture library. Press “OK”.
37
6. FIXTURE SELECTION
Fixture selection
LightShark assigns an ID to each of the patched fixtures, so it can be selected in 3
different ways:
2-Fixture Window: all the fixtures added to the show are shown in this window.
Each selection box includes 3 fields:
DMX address
Fixture ID
1 THRU 8 OK
1 + 8 OK
1 THRU 5 + 8 OK
1 THRU 5 - 3 OK
1 THRU 3 + 6 THRU 8 OK
38
Creating fixture groups
LightShark allows to create fixture groups:
2 Press the “REC” key and select an empty box on the Group window.
A Press the “SET” key and select the fixture group you want to rename.
LightShark will prompt the keyboard on the screen.
B Select the fixture group you want to rename and hold down the box for
2 seconds. LightShark will prompt the keyboard on the screen.
1 Select the fixture group you want to move in the Group windows.
2 Press the “MOVE” key and select an empty box within the Group
window.
39
7. RECORDING SCENES
The programmer storages all the information of the show and LightShark uses this
information when recording Playbacks, Palettes, Groups… A fixture is included in the
programmer when any attribute is modified. The programmer has priority on Playbacks,
Cues, Cuelist and Channels.
The “CLEAR” key will light up when there is information inside the programmer. Press
the “CLEAR” key to delete all that information, and all the LTP Channels will be removed
from the programmer and the HTP Channels will return to zero. In the main menu, it is
possible to choose the behaviour of the “CLEAR” key between all the channels to return
to zero, or to the default value defined in the library.
The “FIND” key activates all the default parameters defined in the library for the fixtures
that are selected.
The Programmer window allows the user to see what is in the programmer and how it
is configured. It is possible to access the programmer window through the window tap.
Cuelist
The Cuelists are used to managed the Cue sequences, ordering the Cues and managing
the options on how they are played. A Cuelist may have either a single Cue or a whole
list of Cues.
A Cuelist is automatically generated when the user records a Cue into a Playback.
LightShark adds that Cuelist to the list of Cuelist stored in the Cues window.
If the Playback has already a Cuelist stored, the new Cue will be added at the end of
that Cuelist.
The Cuelist has a Cue ID (Cue identification) and a text field for each of the Cues, so
every step may be tagged. When the Cuelist is played, the Playback screen will show
the Cue ID and the text field, this way the user may track the actual Cue during the
show.
Recording a Cuelist
1-Recording on an empty Playback
2º-Modify at least one of its parameters (or press “FIND” to activate all
the parameters).
40
4º-Select an empty Playback where the Cue is going to be stored.
LightShark will assign to it the next available Cuelist ID, generating a new
Cue, with the next available Cue ID.
2º-Modify at least one of its parameters (or press “FIND” to activate all
the parameters).
4º-Select the desired Playback. The Cue will be stored at the end of the
Cuelist with the next Cue ID available from the main list.
Modifying Cues
The EDIT command can be used to load the information of a Cue into the programmer.
Once the changes are done, press UPDATE to save them in the original Cue.
Erase a Cue
1º-Go to the Cuelist window and select the Cuelist that includes the
desired Cue.
2º-Press DEL and then tap on the ID number of the Cue to erase.
Copy a Cue
1º-Go to the Cuelist window and select the Cuelist that includes the desired
Cue.
41
8. USING FX
LightShark includes an internal effect generator. The FXs may be directly applied to a
fixture or group of fixtures, it is not necessary to create several Cues to create an effect.
The FXs can be modified live, adjusting the speed and size of the FX to the rate of the
show.
LightShark includes a wide internal FX library (circles, squares, pan, tilt, zigzag,...).
Beam, Colour and Intensity effects are also included.
It is possible to add several effects to a fixture (or group of fixtures) applied to different
attributes. For example, the user may add a Pan effect and also add an Intensity effect
and a Colour-change effect.
LightShark groups the effects in 4 categories: Position, Colour, Beam and Intensity. Each
category may have up to 9 effects max.
42
FX SIZE: it is the range in which the parameter may change. This is
described on the appropriate terms for that parameter only, for example
degrees for the position parameters, or slots for the colour parameters.
It may be modified using the sliders on the screen. When a Size effect is
added, its default will be 50%.
OFFSET: Defines the beginning and end for each effect and determines
how it is played back over all the heads, in order to be stepped.
43
9. SCENE PLAYBACK
The Cuelists may be configured to be played as a Chase (they are automatically played)
or as a simple list of Cues. The main difference is that as a Chase, each of the Cue times
are determined by the speed of the whole Chase. When a Cueslist is configured as a
Cue Step, the times of each Cue are individually determined with their own delay and
fade times.
Playback options
To play a Cuelist you only need to rise the fader on the Playback. LightShark is
configured to start running the Cuelist using the fader. This may be modified using the
Playback Option Menu.
44
Fader Controls HTP Channels: when this function is activated, the
Playback fader controls the level of all the HTP channels proportionally
from 0% to 100%. This is the default option.
45
Fader UP+GO: when the fader exceeds the limit defined in the “trigger
level” field, the Playback is activated and the Cuelist associated is
played. If this option is deactivated the fader will not activate the Cuelist.
Fader at Zero + Release: when the value of the fader is lower than the
limit defined in the “trigger level” field, the Playback is released. If this
option is deactivated the fader will not release the Cuelist.
Lock to all Pages: when this option is activated, the selected Playback
will show up in all 30 pages of Playbacks.
Trigger Level: this field defines the exact value of the fader in which the
Playback is activated or deactivated.
46
Cuelist options
It is possible to configure the way a Cuelist works from the option menu of the Cuelist.
Deactivate after last Cue: when this option is activated, the Cuelist will
automatically release after the last step in the Cuelist.
Deactivate resets to first Cue: when this option is activated, the Cuelist
associated to the Playback will always begin at the first step when is
activated. When this function is deactivated and the user activates the
Cuelist, it will begin at the last step of the Cuelist before releasing.
47
Halt last Cue: when this option is activated, the Cuelist will stop at the
last step. If the option is deactivated, the Cuelist will return to the first
step once the last one is executed.
Pong: going from the first Cue to the Last in order, and then, going
back from last Cue to the first in order.
Chase Speed: It is possible to set the default Chase time for that
particular Cuelist.
Loops: It is possible to set how many times will the Chase be executed
before releasing. By default it is 0, which indicates it will reproduce
infinitely.
48
10.USE OF EXECUTORS
From the Execute window the user can configure a custom layout to trigger the Cuelists.
To add or remove Cuelists from the Execute window press the “Edit” button.
The Execute window is composed of a grid of 8x8 buttons. Each of the 8 vertical
columns can trigger one single Cuelist at the same time, so when selecting a Cuelist
from the same column, it deselects the previous one.
49
The user can modify the color of each of the buttons in the grid, so it is possible to
visually appreciate each of the buttons and assign them a color depending on its
characteristics.
50
It is possible to activate all the Cuelist of all the columns at the same time by sliding the
finger horizontally.
Add Cuelist
The Cuelist can be copied to the execute Window following these steps:
2 On the left-side, select the Cuelist you want to add and press the
“COPY” key. Then select an empty box.
3 Press the “Set” key and then select the box you just created to rename
it.
Empty a box
The Cuelist can be removed from the Execute Window in the following way::
2 Press the “DEL” key and then select the box you want to empty.
51
52