WAVES™ Installation and

Operation Manual
Versions 4.3 and 4.5

October 19, 1999

COPYRIGHT
This manual is copyrighted by MADAH-Com Ltd., all rights reserved. Under the copyright laws, this manual
cannot be reproduced in any form without the prior written permission of MADAH-Com. No patent liability is
assumed, however, with respect to the use of the information contained herein.
© 1997 by MADAH-Com, Ltd. All rights reserved.
EXPORT
This document contains technical data that may be controlled under the U.S. Export Administration Regulations,
and may be subject to the approval of the U.S. Department of Commerce prior to export. Any export, directly or
indirectly, in contravention of the U.S. Export Administration Regulation is prohibited.
DISCLAIMER
This guide has been reviewed for accuracy. Instructions were accurate for the WAVES™ software at the time of
this guide's production. However, succeeding computers and guides are subject to change without notification.
Therefore,
MADAH-Com and WAVES assumes no liability for damages incurred directly or indirectly form errors, omissions
or discrepancies between WAVES and the guide.
TRADEMARK
WAVES is a trademark of MADAH-Com Inc.
All other brand and product names are trademarks or registered trademarks of their respective companies.
LIMITED WARRANTY
Equipment Warranty
MADAH-Com warrants all parts of equipment of its manufacture against defects in material and workmanship
under normal use for one (1) year from the date of original purchase. MADAH-Com, at its option, will at no
charge either repair the equipment (with new or reconditioned parts) or replace it (with a new or reconditioned
equipment), FOB (MADAH-Com), or refund the purchase price of the equipment during the warranty period.
Repaired/replacement equipment is warranted for either 90 days or the remainder of the original warranty period,
whichever is longer. This warranty extends to the original end-user only.
This warranty does not cover: (a) installation or service of the equipment; (b) conditions resulting from consumer
damage such as improper maintenance or misuse, abuse, accident or alteration; (c) all surfaces (including displays)
and all other exposed parts that are scratched or damaged due to normal use; (d) batteries, natural rubber and
material normally consumed in operation unless such items fail as a result of improper application by MADAH-
Com; (e) the operation of our equipments with equipment not supplied by MADAH-Com; (f) equipment which
has had the serial number removed or made illegible; (g) equipment rented to others, or; (h) equipment which has
been repaired or altered by those other than MADAH-Com or its authorized agents.
This warranty applies only to hardware and software manufactured by or for MADAH-Com and identified by the
MADAH-Com trademark, trade name or equipment identification logo affixed to them.
THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. AS EACH EQUIPMENT SYSTEM IS UNIQUE, MADAH-COM DISCLAIMS
LIABILITY FOR RANGE, COVERAGE OR OPERATION OF THE SYSTEM AS A WHOLE UNDER ANY
WARRANTY PROVIDED HEREIN EXCEPT BY A SEPARATE WRITTEN AGREEMENT SIGNED BY AN
OFFICER OF MADAH-COM. MADAH-COM'S CUMULATIVE LIABILITY FOR ANY LOSS OR DAMAGES
RESULTING FROM ANY CLAIMS, DEMANDS, OR ACTIONS ARISING OUT OF OR RELATING TO THE
WAVES PRODUCT OR INCURRED FROM ANY ERRORS, OMISSIONS OR DISCREPANCIES BETWEEN
THE WAVES PRODUCT AND THE USER'S MANUAL, IN NO EVENT SHALL EXCEED THE PURCHASE
PRICE OF THE PRODUCT. IN NO EVENT SHALL MADAH-COM BE LIABLE FOR ANY LOSS OF USE,
LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS, OR OTHER
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO
USE SUCH EQUIPMENT, EVEN IF MADAH-COM HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Service Warranty
To take advantage of this warranty, you must do the following:

i
• For equipment repairs/returns, contact MADAH-Com by dialing (212) 6204413 in the U.S.A. or (972-3)
5330092 in other countries.
• If it is determined that your equipment requires service, you will be issued a Return Material Authorization
(RMA) number. No return will be accepted unless accompanied by an RMA number.
• Pack the defective equipment securely for shipping and mark boxes with the RMA number. Include only the
MADAH-Com equipment that is defective.
• To ensure prompt service, please include a letter indicating the specific cause for returning the equipment.
Ship the defective equipment (freight prepaid), proof of date of purchase, and the RMA number to:
In the U.S.A.: Other Countries:
MADAH-Com Inc. MADAH-Com Ltd.
50 West 23 St 5 Netanyahu Street
New York, NY 10010 Or Yehuda 60376
Attention RMA# Israel
• This warranty is void if the equipment is damaged in transit. Please insure your shipment.
• If warranty repair is applicable, the unit will be repaired and returned freight prepaid.
• If warranty repair is not applicable, the customer will be advised of the repair charges before any costs are
incurred. Non-warranty repairs will be returned FOB (New York, NY) in the U.S.A. or FOB (Tel Aviv) overseas
(except the U.S.A.).
Software Warranty
For One Hundred Twenty (120) days from the date of shipment, MADAH-Com warrants any individual items of
Software delivered to Customer pursuant to the Sales Order against reproducible defects that cause the Software to fail
to conform in material fashion to MADAH-Com published technical specifications for the Software. MADAH-Com
does not warrant that the operation of the Software will be uninterrupted or error free or that each defect in the
Software will be corrected.
In the event of a defect during the applicable warranty period, MADAH-Com, at its sole option, will either repair or
replace the Software or refund the price stated on the Sales Order for the single item of Equipment identified in the
Sales Order that directly malfunctions as a direct result of the Software defect, and such action on the part of
MADAH-Com shall be the full extent of MADAH-Com's liability and customer's exclusive remedy for breach of
the Software warranty. All warranty service will be performed at service locations designated by MADAH-Com.
Travel, transportation and associated expenses of the Customer or such expenses incurred by MADAH-Com for
visits to Customer's location by MADAH-Com personnel are the responsibility of Customer. This warranty
extends only to the Software itself and not the manner in which it interacts with other hardware or software
manufactured by MADAH-Com or others. This warranty does not cover Software which is (i) used in other than
its normal and customary manner; (ii) subjected to misuse, accident or neglect; (iii) subjected to modifications by
Customer or by any party other than MADAH-Com without the prior written consent of MADAH-Com. Non-
MADAH-Com owned computer programs are excluded from this warranty but such computer programs may be
subject to a warranty provided by their manufacturers, a copy(ies) of which will be supplied to Customer, if
available, upon specific written request.
MADAH-Com DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. As each equipment system is unique, MADAH-Com disclaims liability for range, coverage or
operation of the system as a whole under this software warranty except by a separate written agreement signed by
an officer of MADAH-Com.
MADAH-COM SHALL NOT BE LIABLE FOR INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL
DAMAGES, INCLUDING BUT NOT LIMITED TO LOST DATA OR LOST PROFITS, HOWEVER ARISING,
EVEN IF IT HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE LIABILITY OF
MADAH-COM FOR DAMAGES UNDER THIS AGREEMENT SHALL IN NO EVENT EXCEED THE
AMOUNT PAID BY CUSTOMER TO MADAH-COM FOR THE SOFTWARE OR THE SERVICES AS TO
WHICH THE CLAIM AROSE. THE PARTIES AGREE TO THE ALLOCATION OF LIABILITY RISK
WHICH IS SET FORTH IN THIS SECTION.
Any claim for breach of this warranty shall be waived unless Customer notifies MADAH-Com's marketing
representative or MADAH-Com of the defect within the applicable warranty period at: MADAH-Com Inc.,
Attention: Quality Assurance Department.
This Agreement is made in and shall be governed by the laws of the State of New York, excluding choice of law
principles. All proceedings shall be conducted in English. Venue for all proceedings shall be New York County.
The United Nations Convention for the International Sale of Goods shall not apply. The section headings herein
are provided for convenience only and have no substantive effect on the construction of this Agreement. Except

ii
for Customer's obligation to pay MADAH-Com, neither party shall be liable for any failure to perform due to
causes beyond its reasonable control. If any provision of this Agreement is held to be unenforceable, this
Agreement shall be construed without such provision. The failure by a party to exercise any right hereunder shall
not operate as a waiver of such party's right to exercise such right or any other right in the future. This Agreement
may be amended only by a written document executed by a duly authorized representative of each of the parties.
This Agreement may be executed in counterparts.
DEFINITIONS
"Customer" shall mean any purchaser of the Software or Equipment that purchases same for use and not for further
resale or distribution.
"Documentation" shall mean technical publications relating to the use of the Software, such as reference,
installation, administrative and programmer manuals, delivered by MADAH-Com to Customer. Documentation
shall not include marketing materials.
"Equipment" shall mean MADAH-Com's WAVES digital wireless audio visual emergency system.
"Sales Order" shall mean the MADAH-Com product ordering schedules which are signed by both parties to place
orders under this Agreement.
"Software" shall mean all or any portion of the individual items of software (including, without limitation
Documentation relative thereto) identified in the Sales Order to be delivered to Customer subject to this license.
Software shall also include any other software contained in other Equipment identified in the Sales Order and
specifically referred to on the Sales Order as subject to this license.
REGULATORY NOTICE
FCC Part 15 Declaration of Conformity
This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: (a) This
device may not cause harmful interference, and (b) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to FCC
Rules Part 15. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by using the following measures:
• Reorient or relate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.

WAVES Installation and Operation Manual, Version 3.33 Catalog No. IOM-333

iii
TABLE OF CONTENTS

PREFACE
About this manual ..................................................................... ix
conventions USED in this Manual ............................................ xi
Which Chapter Should You Read? .......................................... xii
Getting Help ............................................................................ xiii

CHAPTER 1 INTRODUCING WAVES

1.1 What is WAVES?........................................................... 1-2
1.2 What are the Main Features of WAVES? ...................... 1-3
1.3 How Does WAVES Work? ............................................ 1-4

CHAPTER 2 SYSTEM COMPONENTS

DESCRIPTION
2.1 Base Transceiver (CRLU-201) ..................................... 2-2
2.2 SRLU (CRLU-201)....................................................... 2-3
2.2.1 SRLU Audio/Voice Switching Priorities......... 2-4
2.3 Audio Interface Unit (ADU-301).................................. 2-5
2.4 Personal or Laptop Computer ....................................... 2-7
2.5 Field Transceivers (TRX-401)...................................... 2-8

CHAPTER 3 DESIGNING WAVES SYSTEM

3.1 General.......................................................................... 3-2
3.2 How to Design the WAVES System .............................. 3-4
3.2.1 Determining the location of the speakers......... 3-5
3.2.2 Determining the location of the
VISUAL Display signs .................................... 3-5
3.2.3 Determining the location of data devices......... 3-6
3.2.4 Determining the location of emergency
push buttons and strobe lights.......................... 3-6
3.2.5 Determining the location of the base station.... 3-7

WAVES Installation and Operation Manual v

Table of Contents

3.2.6 Determining the location of the SRLU ............ 3-9

3.2.7 Determining the location of TRX-401,
PRLU and RLX units....................................... 3-9
3.2.8 Designing RF Links ....................................... 3-10
3.2.9 Dividing the site into zones and sub-zones.... 3-11

CHAPTER 4 SETTING UP THE WAVES

SOFTWARE
4.1 Computer Requirements ............................................... 4-2
4.2 Installing the WAVES Software .................................... 4-2
4.3 Starting the WAVES Software....................................... 4-5
4.4 Selecting the Operating Mode ...................................... 4-6
4.5 Closing the WAVES Software ..................................... 4-10

CHAPTER 5 CRATING WAVES DATABASE

5.1 Understanding How the Site Tree is Organized ........... 5-2
5.2 Viewing the Site from the Site Tree ............................. 5-3
5.3 Building the Site Tree ................................................... 5-5
5.3.1 Creating a New WAVES File (.wvs)................. 5-5
5.3.2 Opening an Existing WAVES File.................... 5-6
5.3.3 Defining The Elements in a Site ...................... 5-6
5.3.4 Renaming the Site and its Elements................. 5-8
5.3.5 Deleting a Site Element ................................... 5-9
5.3.6 Reorganizing the Site Tree............................... 5-9
5.3.7 Saving a WAVES File..................................... 5-11
5.3.8 Maintaining Different Unit Settings .............. 5-11
5.3.9 Closing a WAVES File ................................... 5-12
5.4 Using Background Pictures ........................................ 5-13
5.4.1 Preparing background pictures....................... 5-13
5.4.2 Inserting Background pictures ....................... 5-14
5.4.3 VIEWING Background Pictures.................... 5-15
5.4.4 marking background pictures......................... 5-15
5.4.5 Using the Background Picture Buttons.......... 5-18

CHAPTER 6 SETTING PROPERTIES

6.1 General.......................................................................... 6-2
6.2 Audio Properties ........................................................... 6-2
6.2.1 Using the Properties Dialog Box ..................... 6-3
6.2.2 Using the Volume/Mute Control window........ 6-7
6.3 Visual Display Properties ........................................... 6-10
6.4 I/O Control Parameters ............................................... 6-13

vi WAVES Installation and Operation Manual

 Table of Contents

6.4.1 Configuring the Analog and Digital pins....... 6-15

6.4.2 Using the Site Monitor................................... 6-17
6.4.3 Configuring the analog report parameters ..... 6-18
6.5 BIT Parameters ........................................................... 6-22
6.6 Unit ID ........................................................................ 6-27
6.7 Internal Parameters ..................................................... 6-30
6.7.1 Using the Peep Unit Information Monitor ..... 6-33
6.8 Site Properties ............................................................. 6-34
6.8.1 Setting the Emergency Parameters ................ 6-34
6.8.2 Setting the RS-232 Parameters ...................... 6-36
6.8.3 Defining the Log File Parameters .................. 6-37
6.8.4 Defining Audio Mode .................................... 6-39
6.8.5 Defining Audio refresh .................................. 6-42
6.8.6 Defining Report Filter Table.......................... 6-43
6.9 Database Printout ........................................................ 6-48

CHAPTER 7 INSTALLING THE WAVES

HARDWARE
7.1 Safety Precautions......................................................... 7-2
7.1.1 Mechanical ....................................................... 7-2
7.1.2 Environmental.................................................. 7-2
7.1.3 Electrical .......................................................... 7-2
7.2 Unpacking ..................................................................... 7-3
7.3 Installing the Base Station ............................................ 7-4
7.4 Installing the Transceivers ............................................ 7-6
7.4.1 intializing the Transceivers .............................. 7-6
7.4.2 Mounting the Transceivers .............................. 7-8
7.4.3 Connecting Peripherals to a Transceiver ....... 7-10
7.4.4 Installing Alternate Base Station Switch ....... 7-13
7.4.5 Installing a Backup Battery............................ 7-13
7.4.6 Installing Solar Pannels with Backup
Battery............................................................ 7-16
7.4.7 Installing External antennas ........................... 7-19
7.5 Installing the EMP-111 Emergency Push Button ....... 7-24
7.6 Installing EMP-211 Wireless Remote Activator ........ 7-25
7.7 Installing LED Sign .................................................... 7-28
7.8 Installing Strobe Light ................................................ 7-29

CHAPTER 8 OPERATING WAVES

8.1 Adjusting the Volume ................................................... 8-2
8.2 Live Voice Messages .................................................... 8-3
8.2.1 Using a PTT Microphone................................. 8-3

WAVES Installation and Operation Manual vii

Table of Contents

8.2.2 Using a PC-Controlled PTT............................. 8-3

8.3 Sending Visual Display Messages ................................ 8-4
8.4 Working with Pre-Recorded Messages......................... 8-5
8.4.1 Preparing an Audio Message ........................... 8-5
8.4.2 Preparing a Visual display message................. 8-6
8.4.3 Attaching a pre-recorded audio message ......... 8-8
8.4.4 Sending Pre-Recorded audio visual Messages
(AVM).............................................................. 8-8

CHAPTER 9 ADVANCED FEATURES

9.1 WACOL Command Language ..................................... 9-2
9.1.1 Working with WACOL statements.................. 9-2
9.1.2 Custom Commands .......................................... 9-8
9.2 The WACOL Shell ....................................................... 9-9
9.3 The Scheduler ............................................................. 9-11
9.4 Alternate Base Station ................................................ 9-13

CHAPTER 10 THE RS-232 DATA CHANNEL

10.1 General........................................................................ 10-2
10.2 Opening a Link from the Base Station........................ 10-2
10.3 Opening a link from the field...................................... 10-3
11.1 General ........................................................................ 11-2

CHAPTER 11 ICM-501 - INTERCOM CONTROL

MODULES
11.2 ICM-501 Panel Description ........................................ 11-3
11.3 Installing the ICM-501................................................ 11-3
11.3.1 Mounting the ICM-501 on the
Transceiver Unit............................................. 11-4
11.3.2 Installing the ICM-501f ................................. 11-6
11.3.3 Installing the ICM-501b................................. 11-8
11.4 ICM-501 External Interface........................................ 11-9
11.5 Operating the ICM-501............................................. 11-10
11.6 Using the Intercom Utility Program ......................... 11-13
11.6.1 Setting the Communication with the
ICM-501....................................................... 11-14
11.6.2 Downloading/Updating the
ICM-501 Software ....................................... 11-15
11.6.3 Setting the ICM-501 Internal Parameters .... 11-16

viii WAVES Installation and Operation Manual

 Table of Contents

CHAPTER 12 WAVES EXTERNAL INTERFACES

12.1 OLE Interface .............................................................. 12-2
12.2 DTMF Control Application ......................................... 12-3
12.2.1 Introduction.................................................... 12-3
12.2.2 Principle of Operation.................................... 12-3
12.2.3 Installing the Dialogic telephone card ........... 12-4
12.2.4 Setting the DTMF Control Application ......... 12-7
12.3 RS-232 Interface ....................................................... 12-11

APPENDIX A VERSION UPDATE PROCEDURE

APPENDIX B TROUBLESHOOTING

APPENDIXC TRANSMITTING OFFSET

ASSIGNMENTS

APPENDIX D EQUIPMENT SPECIFICATIONS

APPENDIX E CBU-721 CONTROL BOX

APPENDIX F COMFUTURE PROTOCOL

SETTINGS

APPENDIX G LIST OF CABLES

APPENDIX H EMA-211-WRX INSTALLATION AND

OPERATION INSTRUCTIONS

WAVES Installation and Operation Manual ix

PREFACE

Congratulations! You have just purchased WAVES•, the most

advanced audio and data wireless network available on today’s
market.

We, at MADAH-Com, are proud of our products and have

designed this Installation and Operations Manual to make
installation and operation simple and straightforward.

ABOUT THIS MANUAL

This manual provides detailed information for installing and
operating the WAVES system. The following chapter summary
and the flow chart on page xiv should help you to decide which
chapters address your needs.

Chapter 1 Introducing WAVES

Presents the WAVES system, its main features and principle of
operation.

Chapter 2 System Components Description

Gives an in-depth discussion of the WAVES system
components.

Chapter 3 Designing the WAVES system

Describes how to design the WAVES system. It introduces the
site plan, and discusses how to determine the location of the site
elements. It also explains how to design the RF links and zone
organization.

Chapter 4 Setting Up the WAVES Software

Presents complete software installation and startup procedures.
It also includes a description of the main screen and the
operational modes.

WAVES Installation and Operation Manual xi

Preface

Chapter 5 Creating WAVES Database

Describes how to build the site tree and how it is organized. It
also explains how to prepare and insert background pictures
into Units window.

Chapter 6 Setting Properties

Explains how to set up the operating parameters of the site and
site elements.

Chapter 7 Installing the WAVES Hardware

Presents complete installation instructions for all WAVES
components.

Chapter 8 Operating WAVES

Presents the functions required for the routine operation of
WAVES. In this chapter, you will learn how to adjust the volume,
transmit voice and text messages, prepare and save audio and text
messages for future use, and transmit pre-recorded voice and text
messages.

Chapter 9 Advanced Features

Describes the WAVES system’s advanced features, including the
WAVES Command Language (WACOL), the WACOL shell,
the Scheduler, and the Alternate base station.

Chapter 10 The RS-232 Data Channel

Describes opening a full duplex link between the CRLU and a
data device connected to a field transceiver.

Chapter 11 ICM-501 Intercom Control Models

Describes the ICM-501 installation and operation, and the
Intercom utility program.

Chapter 12 WAVES External Interfaces

Describes the OLE interface, DTMF control application, and
RS-232 interface.

xii WAVES Installation and Operation Manual

 conventions USED in this Manual

CONVENTIONS USED IN THIS MANUAL

The following conventions are used throughout this manual:

This Represents

ALL CAPITAL LETTERS A key on the keyboard

Icon to the left of a procedure Shortcut to the command

described in the procedure

WAVES Installation and Operation Manual xiii

Preface

WHICH CHAPTER SHOULD YOU READ?

Are you
fam iliar with the No
WAVE S system ? Read Chapters 1 & 2
To u n d e rs ta n d h o w W AV E S w o rks a n d w h a t
e a c h co m po ne nt in th e W AV E S sy ste m d o e s.

A re you
responsible for
installing the WAVES Ye s Read Chapter 4
software?
To in s ta ll th e W AV E S s o ftw a re .

Are you
new to WAVES ? Ye s Read Chapter 3
To un de rs ta nd th e W AV E S sta rtup proc ed ure
a n d u se r in terfa c e. C o n tin u e to C h a p te rs 4 , 5 , 6
a n d 9 fo r in -d e p th d isc us sion o f p roc ed ures .
Are you
responsible for the Ye s
WAVE S database?
Read Chapters 3 & 5
To se t u p o r m o d ify th e s ite tre e .

W ill you be using

background pictures? Ye s Read Chapter 5
To le a rn h o w to w o rk w ith ba ck g ro u n d
p ic tu re s .

Will you be
perform ing configuration Ye s Read Chapter 6
m odifications?
To se t u p or m od ify op eratin g p ara m e ters .

Are you
responsible for
installing the WAVES Ye s Read Chapter 7
hardw are?
To in s ta ll a ll th e h ardw a re co m p o n e n ts . C o n tin u e
to C h a p te r 11 if yo u n e e d to in sta ll th e IC M -5 0 1 .

Are you
the WAVES operator? Ye s Read Chapter 8
To le a rn h o w to o pe ra te W AV E S .

xiv WAVES Installation and Operation Manual

 Getting Help

GETTING HELP
Please forward all comments or queries to:

In the U.S.A.: Other Countries:

MADAH-Com, Inc. MADAH-Com, Ltd.
50 West 23 rd St 5 Netanyahu Street
New York, NY 10010 Or Yehuda, Israel 60376
Tel.: (212) 620-4413 Tel.: (9723) 533-0092
Fax: (212) 620-4439 Fax: (9723) 533-1376
e-mail: [email protected] e-mail: [email protected]

WAVES Installation and Operation Manual xv

CHAPTER 1

INTRODUCING WAVES

This chapter includes the following sections:

x What is WAVES?
x What are the main features of WAVES?
x How does WAVES works?

WAVES Installation and Operation Manual 1-1

Introducing WAVES

1.1 WHAT IS WAVES?

WAVES is a wireless information distribution command, control
and monitoring network that uses Frequency Hopping Spread
Spectrum (FHSS) technology to broadcast background music,
voice announcements and visual display messages.

The WAVES software (MMI-701) provides intuitive and easy

grouping, zoning and real-time control of audio and data
messages. Message and control sequences can be saved as
presets. A programmable scheduler automatically cues pre-
recorded messages and presets. Visual messages can be
broadcast in real-time or saved to disk for later use.

WAVES offers substantial advantages over traditional hard-

wired public address systems:
x Fast and easy installation that saves time and expense.
x Reliable, secure and virtually interference-free digital
communications. WAVES transceivers are programmed to
automatically re-route communications in case of a point
failure.
x Flexible modular design that enables rapid adjustments and
acoustic optimization.
x Advanced command and control monitoring.
x Backup battery for each transceiver.
x Simple maintenance through built-in tests (BIT) that
monitors the status of the hardware and report the results to
the base station.
x Total Site-Coverage™ in heavily constructed indoor
facilities and open outdoor facilities.
x Americans with Disabilities Act (ADA) compliant,
synchronized audio and visual data. Audio and text files can
be programmed for broadcast to specific locations and at
specific times.
x Full duplex RS-232 data channel.

1-2 WAVES Installation and Operation Manual

 What are the Main Features of WAVES?

1.2 WHAT ARE THE MAIN FEATURES OF

WAVES?
x Frequency Hopping Spread Spectrum system that operates
at a worldwide license-free frequency of ISM band
2.4 GHz.
x Permanent, temporary or portable operation.
x Two wide band audio channels plus one bi-directional data
channel (RS-232) for transmitting audio messages
synchronized with a visual display message.
x Fault tolerant design that enables each transceiver to
communicate with two others in the system.
x “Plug and Play” operation.
x Pre-recorded message library with a built-in multiple
message, multiple event scheduler.
x Total Site-Coverage™ of any size facility.
x Continuous real-time system control, data monitoring and
system supervision.
x Windows-based intuitive graphical interface (GUI) that
displays scanned site images for realistic site layout and
graphic control.
x Analog and digital I/Os for command and control
x Built-in test for immediate and automatic faults detection
and output supervision.
x Hard disk recording and playing of audio and visual
messages and presets.
x ADA compatible for new and retrofit installation.
x WAVES Command Language (WACOL) for
implementation of command and control applications over
external devices.

WAVES Installation and Operation Manual 1-3

Introducing WAVES

1.3 HOW DOES WAVES WORK?

WAVES uses FHSS technology to broadcast radio (RF) signals
over a wide range of frequencies. Frequency offsets are used to
spread the RF signals. Receiving stations use their frequency
offset settings to recognize and retrieve RF signals directed to
them.

The WAVES system consists of a base station and up to 16,384

uniquely addressable field transceivers.

Figure 1-1 The WAVES System

The base station contains a base transceiver (CRLU-201), an

audio and data interface unit (ADU-301) and an optional
personal or laptop computer using the WAVES software.

From the base station, WAVES can transmit two high-fidelity

audio channels multiplexed with a full duplex data channel that
receives and transmits signals to onsite control and monitoring
I/Os. This enables the WAVES operator to transmit an audio
broadcast and a voice announcement at any given time and
synchronize them with a display message sent on the data
channel.

The field transceivers can independently process information

selectively transmitted to them from the base station or from
local inputs. They then amplify the audio signals for the
speakers and send the data to the visual display signs and other
data devices connected to them. This enables the WAVES
designers to adapt each transceiver to its immediate acoustic
environment and the WAVES operators to adapt each transceiver
to changing conditions. In this way, acoustic quality and
transceiver integrity can be maintained.

Each transceiver is also programmed to communicate with two

other transceivers (primary and secondary) in the receiving

1-4 WAVES Installation and Operation Manual

 How Does WAVES Work?

channel. This means that signal flow is not affected if the

primary transceiver fails. Instead it is automatically rerouted
through the secondary transceiver.

Finally, the WAVES operator at the base station has full real-
time control of each transceiver’s audio and data parameter
settings, enabling the operator not only to control the audio and
data settings but to also monitor each transceiver’s operating
parameters.

WAVES Installation and Operation Manual 1-5

CHAPTER 2

SYSTEM COMPONENTS
DESCRIPTION

This chapter includes the following sections:

x Base transceiver (CRLU-201)
x SRLU (CRLU-201)
x Audio interface unit (ADU-301)
x Personal or laptop computer
x Field transceivers (TRX-401)

WAVES Installation and Operation Manual 2-1

System Components Description

2.1 BASE TRANSCEIVER (CRLU-201)

The CRLU-201 is the base transceiver unit of the WAVES
system. It transmits multiple channels of audio and visual
display messages and RS-232 data and control information for
wireless distribution within the WAVES system. At the same
time, it receives RS-232 data and network-wide supervisory
diagnostics (BIT) reports for subsequent transmission to the
WAVES software.

Antenna
Panel Cover

Sync
Indicator

Connector
Panel Cover

Connector Panel

Figure 2-1 CRLU-201

The CRLU-201 is a fully integrated unit with an integral power

supply, audio amplifiers and diversity antenna. It digitizes
incoming analog audio streams from the ADU-301 and
communicates with the ADU-301 through a multi-pair-shielded
cable terminated in a DB-25 connector. RS-232 data is
communicated through a DB-9 connector.

You can also program the CRLU-201 to function as a TRX-401

field transceiver. As a field transceiver, the CRLU-201 can
receive and transmit signals on two channels of wideband
audio, one full duplex RS-232 data channel (at up to 9.6 kbps),
one analog input and three digital I/O data pins.

The CRLU-201 is housed in a weather-resistant extruded

aluminum enclosure with ABS plastic covers. It mounts easily
onto the back plate supplied with the unit.

The CRLU-201 can be powered locally from either an AC (100-

240V, 47-63Hz) or DC (12-16V) power source or remotely

2-2 WAVES Installation and Operation Manual

 SRLU (CRLU-201)

from the ADU-301 through the CAB-ADU-25/9-CRLU-4

cable. An optional backup battery (UPS-901) can provide up to
five hours of operation. UPS-901 batteries are stackable,
enabling you to extend backup time.

Notes: a) All the CRLU-201 and UPS-901 circuits have a

Class 2 rating.
b) You can address the following functions to the
CRLU: PTT, volume, discrete I/O and audio
messages. You cannot address visual messages to
the CRLU.

For detailed information on the CRLU-201, see the Base

Transceiver Unit data sheet in Appendix D.

2.2 SRLU (CRLU-201)

You can program the CRLU-201 to function as a Satellite Relay
Unit (SRLU). The SRLU is used as a relay, and has the
following capabilities:
x Independent audio source for the SRLU sub-tree. Used for
local announcements, or when more than two audio sources
are needed.
x Alternate Base Station for backup purpose.

The following diagram is an example of an application with

SRLU:

WAVES Installation and Operation Manual 2-3

System Components Description

Figure 2-2 Example of an Application with SRLU

The SRLU can be configured to one of two modes: Local or

Base. In Local mode, the audio inputs (the output from the local
ADU) are transmitted to the SRLU zone only. In Base mode,
the audio channels received from the CRLU are transmitted to
the SRLU zone.

You can activate the SRLU as an Alternate Base Station by

switching the Alternate Base Station switch to this mode
manually (the Alternate Base Station switch box is connected to
pin 3 – ground, and pin 10 in J2 connector in the SRLU).

2.2.1 SRLU AUDIO/VOICE SWITCHING PRIORITIES

The SRLU voice operation depends on the PTT received from
the local ADU or the CRLU. The following table describes the
priorities of the voice inputs (microphone, sound card,

2-4 WAVES Installation and Operation Manual

 Audio Interface Unit (ADU-301)

background music and intercom) in Base mode and Local

mode.

Table 1-1. PTT priorities when SRLU is in Base mode

Base SRLU SRLU Zone Selected Channel
PTT PTT addressed
Normal Normal Don’t care Channel
Normal PTT Don’t care Voice (local)
PTT Normal Yes Channel (voice)
No A (or A+B) (local)
PTT PTT Don’t care Voice (local)
Table 1-2. PTT priorities when SRLU is in Local mode
Base SRLU SRLU Zone Selected Channel
PTT PTT addressed
Normal Normal Don’t care A (or A+B)
Normal PTT Don’t care Voice (local)
PTT Normal Yes Channel (voice)
No A (or A+B) (local)
PTT PTT Don’t care Voice (local)

2.3 AUDIO INTERFACE UNIT (ADU-301)

The ADU-301 is the central audio and data interface unit of the
WAVES system. It provides an interface between its input audio
and data channels and the CRLU-201. It also provides an
interface between the optional PC and the CRLU-201. The
CRLU-201 subsequently communicates with the TRX-401 field
transceivers.

Figure 2-3 ADU-301 Front and Rear Panels

WAVES Installation and Operation Manual 2-5

System Components Description

Two balanced or unbalanced line-level audio sources (ChA and

ChB) can be connected via the XLR connector or the ¼” (phone
jacks on the rear panel of the ADU-301). Each channel level
can be adjusted using the -20dB pad, the +30dB trimmer and
the peak/clip LED indicators (on the front and rear panels).

A PC sound card can be connected (TO/FROM) via stereo

phone jacks provided on the rear panel.

A microphone can be connected via the XLR connector or the

¼” phone jack on the front panel. The microphone input
includes a pre-amplifier and soft-limiter compressor. The
microphone can be activated via the front panel PTT switch or
from an external control signal connected to a ¼” phone jack.

The ADU voice output depends on one of the three voice

inputs, and on the following priorities:

Top priority – Microphone + PTT

When pressing the PTT, the microphone is enabled, and any
other voice signal is disabled.

Second priority – Intercom

When using a field intercom in paging mode, the audio output
passes through the base intercom and the ADU, and is then
transmitted in burst broadcast through the CRLU (see also
chapter 11 – ICM-501 Intercom Control Modules).

Third priority – Sound card

When activating a message through the PC (by the scheduler or
AVM message), the audio output is transmitted.

A monitor stereo speaker/headphone output with adjustable

gain up to 4 watts per channel is provided via a ¼” phone jack
on the front panel (Tip – Channel A + Voice and Ring –
Channel B + Voice).

The ADU-301 offers RS-232 to RS-422 conversion. It provides

an interface between the optional PC (RS-232 via its DATA
PORTS: TO PC CONTROL connector) and the CRLU-201
(RS-422 via its DATA PORTS: To CRLU connector).

The ADU-301 provides a bridge between a data device and the

CRLU-201 RS-232 connector via its DATA Ports: RS-232 TO
CRLU and RS-232 connectors.

2-6 WAVES Installation and Operation Manual

 Personal or Laptop Computer

The ADU-301 also provides a bridge between the onsite

intercom system and the base station via the ICM connector on
its rear panel.

The ADU-301 can be powered locally from an AC (100-240V,

47-63Hz) power source. It can also provide power to or receive
power from the CRLU-201 through the CAB-ADU-25/9-
CRLU-4 cable.

The ADU-301 has a matte black metal enclosure and measures

1.75” x 19” x 9” (1 rack unit). It can be mounted in a standard
equipment rack.

Note: All the ADU-301 circuits have a Class 2 rating.

For detailed information on the ADU-301, see the Audio

Interface Unit data sheet in Appendix D.

2.4 PERSONAL OR LAPTOP COMPUTER

(Optional)
If you decide to install a personal or laptop computer at the base
station, the WAVES software (MMI-701) enables the computer
to serve as the command center of the system.

Using the WAVES software, you can monitor the transceivers in

your site from the base station, group them into zones and sub-
zones to facilitate real-time control of audio, voice and data
messages, pre-record and save messages and schedule message
broadcasts.

WAVES Installation and Operation Manual 2-7

System Components Description

2.5 FIELD TRANSCEIVERS (TRX-401)

Each field transceiver (TRX-401) is an addressable node in the
wireless network that receives and broadcasts messages
addressed only to that transceiver. You can setup a field
transceiver as a PRLU (relay unit) or an RLX (end unit).

Antenna Panel Cover

Sync Indicator

Connector Panel Cover

Connector Panel
Figure 2-4 TRX-401

Using the WAVES software, you can assign a unique address in

the WAVES network to each TRX-401.

The TRX-401 is a fully integrated unit with an integral power

supply, audio amplifiers and a diversity dual antenna. It also
supports connections to optional external antennas.

The TRX-401 supports the following interface connections:

x Powered audio output. Supports two 15W channels for
amplified audio output to speakers (4 ohms per channel).
x Two balanced line level audio output channels.
x RS-232. Connects data devices, i.e., text display boards or
the ICM-501F.
x Configurable I/O signals. Permits site control and
monitoring.

The TRX-401 is housed in a weather-resistant extruded

aluminum enclosure with ABS plastic covers. It mounts easily
onto the back plate supplied with the unit.

2-8 WAVES Installation and Operation Manual

 Field Transceivers (TRX-401)

The TRX-401 can be powered from an AC (100-240V, 47-

63Hz) or DC (12-16V) power source. An optional backup
battery (UPS-901) can provide up to five hours of operation.
UPS-901 batteries are stackable, enabling you to extend backup
time.

Note: All the TRX-401 and UPS-901 circuits have a Class 2

rating.

For detailed information on the TRX-401, see the Field

Transceiver Unit data sheet in Appendix D.

WAVES Installation and Operation Manual 2-9

CHAPTER 3

DESIGNING WAVES
SYSTEM

This chapter includes the following sections:

x General
x How to design the WAVES system

WAVES Installation and Operation Manual 3-1

Designing WAVES System

3.1 GENERAL
Designing the WAVES system involves the following main
steps:
x Determining the location of the system components
x Designing the RF links
x Dividing the WAVES units to zones and sub-zones (zone
organization)

At the conclusion of this procedure, you will see a graphic

representation of the WAVES network and organization (see
Figure 3-1). It provides a conceptual map with the location of
the units, speakers and antennas, as well as definitions of all RF
links (primary and secondary).

Figure 3-1 is an example for a typical site plan. The site plan
represents two main point views: zone organization and RF
links.

The zone organization is a hierarchical structure of the zones

and sub-zones that is shown (later) as a site tree in the WAVES
application. This division is derived from the need to group
units for specific activities, such as sending addressed
announcements, sending pre-recorded messages and etc.

The RF links represent the RF connection between the units.

For each unit, two potential sources are defined for acquiring
(the parameters are defined in the database for each unit). There
is no association between the RF links and the zone
organization, meaning that a unit can be part of one zone and
receive signals from another zone (except in case of SRLU
configuration; for more details refer to SRLU description in
chapter 2).

3-2 WAVES Installation and Operation Manual

 General

Figure 3-1 Site Plan Typical Example

WAVES Installation and Operation Manual 3-3

Designing WAVES System

3.2 HOW TO DESIGN THE WAVES SYSTEM

In designing the WAVES system, we recommend that you:
Determining 1. Determine the location of the speakers
the location according to the acoustic requirements.
2. Determine the location of the visual
display signs according to the
environment requirements.
3. Determine the location of the data
devices.
4. Determine the location of the emergency
push buttons (wired and wireless) and the
strobe lights, according to the
environment requirements.
5. Determine the location of the base
station.
6. Determine the SRLU location (if
required).
7. Determine the location of the field relays
and field receivers.
Defining the 8. Draw the RF links between all of the
RF links units.
Organizing 9. Divide the site into zones and sub-zones.
the zone

3-4 WAVES Installation and Operation Manual

 How to Design the WAVES System

3.2.1 DETERMINING THE LOCATION OF THE SPEAKERS

When selecting a location for the speakers, we recommend that
you:
1. Determine the required audio power in each location.
2. Determine the speaker type for each location. For example,
ceiling speakers and/or wall speakers and horn speakers.
3. Select the speakers according to the required optimal
dispersion angle in the installation. For example, horn
speaker with dispersion angle of 90q or 120q.
4. Note that the maximum power from the WAVES unit is
achieved with 4 : impedance.
5. When connecting a number of speakers to a single WAVES
unit, connect the speakers in combination of serial and
parallel connections to achieve the 4 : impedance.
6. To reduce the cable attenuation, take into accounts the
length and thickness of the cables. If necessary, use audio
transformers for impedance matching.

3.2.2 DETERMINING THE LOCATION OF THE VISUAL DISPLAY

SIGNS
When selecting locations for the visual display signs, we
recommend that you:
1. Place visual display signs where they can be visible to a large
audience. Since the transceiver and visual display sign
communicate through an RS-232 interface, the maximum
distance between the transceiver and the visual display sign is
240 ft. (74 m) if using shielded cable and 120 ft (37 m) if
using unshielded cable.
2. Make sure that AC power or an alternate power source is
available at the visual display signs location.

WAVES Installation and Operation Manual 3-5

Designing WAVES System

3.2.3 DETERMINING THE LOCATION OF DATA DEVICES

When selecting locations for the data devices (Intercom, PC or
any unit that communicates through an RS-232 interface), we
recommend that you:
1. Select the location according to the needs of the operators.
2. For devices that operate with independent power supply
(not from WAVES unit), the distance from the WAVES unit
can be 240 ft. (74 m) for shielded cable and 120 ft. (37 m)
for unshielded cable.
3. For devices that operate with DC power supplied from
WAVES unit, the distance from the WAVES unit is limited
according to the cable attenuation and the device’s current
consumption.
4. When locating the ICM-501 intercom and handset, the
distance from the WAVES unit is limited to the supplied
cable length.

3.2.4 DETERMINING THE LOCATION OF EMERGENCY PUSH

BUTTONS AND STROBE LIGHTS
WHEN selecting locations for the emergency push buttons
(wired and wireless) and strobe lights, we recommend that you:
1. For wired emergency push buttons, the distance from the
WAVES unit to the emergency push button is limited
according to the cable attenuation (less than 500 :).
2. For wireless emergency push buttons, the distance between
the EMP-211-WRX (receiver unit) and the WAVES unit is
limited according the cable attenuation (less than 20 :). For
A typical cable, the distance can be up to 130 ft. (40 m).
3. For strobe lights, the distance between strobe light and the
WAVES unit is limited according to the power consumption
and cable attenuation of the strobe light. For example, the
strobe light supplied by MADAH-Com consumes 0.2 A and
the voltage drop can be up to 2 V, so the cable resistance
can be up to 10 :. For a typical cable, the distance can be
up to 65 ft. (20m).

3-6 WAVES Installation and Operation Manual

 How to Design the WAVES System

3.2.5 DETERMINING THE LOCATION OF THE BASE STATION

When selecting location for the base station, we recommend
that you:
1. Place the base station’s CRLU in a central location where it
can serve as many WAVES units as possible.
2. Place the ADU as close as possible to the operator station.
3. Due to cable length considerations, take the following into
account:
x Maximum distance between the ADU-301 and CRLU-
201 is 350 ft (105 m)
x Maximum distance between a transceiver (CRLU-201
or TRX-401) and an external antenna is 10 ft (3 m)
(Consult MADAH-Com if a larger distance is required).
x Maximum distance between the computer (optional)
and ADU-301 is 120 ft. (37 m) for shielded cable and
60 ft (18 m) for unshielded cable.

The following is a typical example of a base station (or

alternate base station), located inside a building that has
a number of floors.

WAVES Installation and Operation Manual 3-7

Designing WAVES System

Figure 3-2 Typical Locations for Base Station Units

4. Note specific objects on the site that may constitute an RF

obstacle, such as metal objects, reinforced concrete and
heavy foliage. Where appropriate, consider using external
antennas.
5. Do not place a transceiver near RF equipment operating at
2.4 GHz, such as a microwave oven.
6. Make sure that AC power or an alternate power source is
available at locations of WAVES units.

3-8 WAVES Installation and Operation Manual

 How to Design the WAVES System

7. It is recommended to supply power for every unit

independently. If necessary, and if the cable length between
the ADU and the CRLU is less than 32 ft. (10 m), you can
supply the power to the CRLU by the ADU.
8. Provide proper grounding and protection for all equipment,
including components of the base station and antennas
mounted on roofs or masts.

Warning When the antenna is mounted on a roof, you must

provide lightning and electrical protection.

3.2.6 DETERMINING THE LOCATION OF THE SRLU

The considerations for determining the best location for the
SRLU are the same as in CRLU considerations, since the SRLU
usually is used as an alternate base station (see section
3.2.5 Determining the location of the base station).

Note: For connection of the alternate base station switch, see

section 7.4.4.
For SRLU operation, see section 9.4.

3.2.7 DETERMINING THE LOCATION OF TRX-401, PRLU AND

RLX UNITS
1. Determine the best location for the base unit, relays (if
needed) and end units. Note specific objects on the site that
may constitute an RF obstacle, such as metal objects,
reinforced concrete and heavy foliage. Where appropriate,
consider using external antennas.
2. Do not place a transceiver near RF equipment operating at
2.4 GHz, such as a microwave oven.
3. Avoid placing within two meters of each other two
unrelated transceivers (do not receive from or transmit to
each other RF signals).
4. Make sure that AC power or an alternate power source is
available at the field transceiver locations.

WAVES Installation and Operation Manual 3-9

Designing WAVES System

5. Due to cable length considerations, take into account that the

maximum distance between a field transceiver and its visual
display sign or other data device is 240 ft. (74 m) for
shielded cable and 120 ft (37 m) for unshielded cable.
6. Provide proper grounding and protection for all equipment,
including components of the base station and antennas
mounted on roofs or masts.
7. Place relays in a location where they can serve as many
transceivers as possible, and where they can also serve as
normal WAVES nodes to drive speakers, etc.

3.2.8 DESIGNING RF LINKS

1. If you think that in a specific area you might have poor RF
signal reception, it is recommended to test the receiving
quality with mobile WAVES unit, and, if necessary, change
the location or add another relay unit.
2. To overcome possible reception failures, WAVES has a
backup radio frequency (RF) channel for each transceiver.
Setting the receiving offsets to a specific value (0-75)
determines the RF channels used by the transceiver. Take
care to define the correct primary (main) and secondary
(backup) offset values (see Chapter 6).
3. When defining two potential sources for the TRX, consider
the following:
 When the TRX stops receiving from one of the sources,
it searches for the other source (if it exists and
transmits) and locks on it.
 When the reception quality from one source is poor (20
CRC errors in the audio signals for maximum 10
seconds), it searches for the other source (if it exists and
transmits) and tries to lock on it for better quality
reception.
4. When installing TRX-401 units at a zone with SRLU, verify
that all RF paths of the units originated only at the SRLU.
WAVES system enables the operator to define RF links and
zone organization independently. For example (see Figure
2-2), a TRX that is part of zone 1 can receive from a PRLU
in zone 2. When configuring zone 3 with SRLU, the TRX
in zone 3 must receive only from the SRLU or through
another TRX in the same zone, in order to prevent

3-10 WAVES Installation and Operation Manual

 How to Design the WAVES System

disconnection from the SRLU’s audio source. Means that,

when a unit is part of a zone controlled by the SRLU, verify
that the unit’s RF link is defined as part of that SRLU zone.
5. Perform simulation of relay failure, and check that there is no
single point failure in the system (except SRLU). In Figure 3-
1, if the base station fails, the alternate base station is
activated as base station (manually) and transmits to the other
WAVES units.
6. Record the parameters of each transceiver (i.e., Unit Address,
Unit Type, Unit ID, TX Offset, Primary RX ID, Primary RX
Offset, Secondary RX ID and Secondary RX Offset) in a
table (as shown) for later reference.
Unit Unit Type Unit ID TX Offset Primary Primary Secondary Secondary
Address * RX ID RX Offset RX ID RX Offset

*Fill the Unit Address column only after designing the zone organization.

3.2.9 DIVIDING THE SITE INTO ZONES AND SUB-ZONES

Group units to zones and sub-zones according to the addressing
needs of the site. For example, the engineering division can be
one zone and the departments in the engineering division can be
the sub-zones.

Keeps in mind the following software consideration: WAVES

can support up to 64 zones, 16 sub-zones per zone and 64 units
per sub-zone.

Note: When including also an SRLU, remember that all the

units are part of the SRLU zone or sub-zones only.

WAVES Installation and Operation Manual 3-11

CHAPTER 4

SETTING UP THE WAVES

SOFTWARE

This chapter includes the following sections:

x Computer requirements
x Installing the WAVES software
x Starting the WAVES software
x Selecting the operating mode
x Closing the WAVES software

WAVES Installation and Operation Manual 4-1

Installing the WAVES Software

4.1 COMPUTER REQUIREMENTS

Before installing the WAVES software, check that your
computer meets the following minimum requirements:
x Pentium 133 MHz or higher
x 32 MB RAM
x 10 MB free space on the hard disk
x Microsoft Windows95™, Windows98™ or Windows NT™
x SVGA (800 x 600) monitor and video card
x Sound card (i.e., 16-bit Sound Blaster)
x 2 serial ports (one standard port and one optional for
external control box, see chapter 12)
x DTMF card (optional for telephone remote control, see
chapter 12)

4.2 INSTALLING THE WAVES SOFTWARE

The WAVES software enables you to not only control your
WAVES system from the base station but also to set up the
transceivers (CRLU-201 and TRX-401). Therefore, whether or
not you install a PC at the base station, you need the WAVES
software to configure and install the WAVES system.

³ To install the WAVES software from diskettes:

1. Exit all open applications.
2. Insert WAVES Graphical User Interface Disk 1 into
drive A or drive B.
3. Click the Start button and then click Run.
4. In the Run dialog box, type a:\setup.exe or b:
\setup.exe.
5. Follow the instructions on the screen.
Note: Make sure you select typical installation.

After successful installation, the WAVES icon appears on

your desktop.

4-2 WAVES Installation and Operation Manual

 Installing the WAVES Software

³ To install the WAVES software from a CD:

1. Close all open applications.
2. Insert WAVES Graphical User Interface CD into the
CD-ROM drive.
3. Click the Start button and then click Run.
4. In the Run dialog box, type d:\setup.exe (where d:\
represents your CD-ROM drive).
5. Follow the on-screen instructions.
Note: Make sure you select typical installation.

After successful installation, the WAVES icon appears on

your desktop.

Configuring the Serial Port

At the end of the installation, COM 2 is defined as the standard

serial interface. You can change this setting according to your
preferences.

WAVES Installation and Operation Manual 4-3

Installing the WAVES Software

³ To change the serial port setting

1. From WAVES shortcut, click the right button and select
Properties. The Properties window appears.

Port
number

2. In the Shortcut tab, in Target field, change the port

number (e.g. c3 means COM 3).

4-4 WAVES Installation and Operation Manual

 Starting the WAVES Software

4.3 STARTING THE WAVES SOFTWARE

³ To start the WAVES software:
x Double-click the WAVES icon.
The main window appears.

Toolbar

Action Panel

The WAVES main window has a toolbar and an action panel.

The horizontal toolbar is located immediately below the menu
bar and the vertical action panel is located to the left of the main
window.

The toolbar and action panel contain buttons which correspond

to many of the menu commands. You can find out what each
button does by pointing to a toolbar or action panel button. The
name of the button appears in a yellow tool tip to the right of
the button.

³ To display or hide the toolbar:

x On the View menu, point to Toolbars and do one of the
following:
 Click a toolbar or the action panel.
 Click Show All.
 Click Hide All.

WAVES Installation and Operation Manual 4-5

Installing the WAVES Software

4.4 SELECTING THE OPERATING MODE

You can work with the WAVES software in one of four
operating modes:
x User
x Off-line
x On-line
x Wired

When you start the WAVES software, User mode is active. The
other three operating modes are password protected, and allow
access to permitted personnel only.

The User mode allows you to carry out general operations, but
no database operations (for details, see table 4-1). You can
activate the other modes using a password (the default password
is “WAVES”).

The Off-line mode enables you to work off-line. In this mode,

you can design site trees and make changes to the design of
existing site trees (see Chapter 5). You can also adjust the
property settings of the CRLU and field transceivers (see
Chapter 6).

The On-line mode enables you to control the on-line operation

of the WAVES system through the connection between the
computer at the base station and the CRLU (see Chapters 8, 9
and 10). In this mode, you can receive BIT reports (see Chapter
6), design or make changes to the design of a site tree (see
Chapter 5), adjust the property settings of the CRLU and field
transceivers, refresh the current operating parameters and
reconfigure an entire site (see Chapter 6).

To ensure the integrity of the site tree, it is recommended that

you redesign the site tree off-line and only update the site tree
after you are satisfied with the new design.

Note: When you change the address or properties of a unit on

the site tree in on-line mode, the base station PC
generates a message to the corresponding field
transceiver and waits for an acknowledgement. If the
base station PC receives an acknowledgement, it

4-6 WAVES Installation and Operation Manual

 Selecting the Operating Mode

updates the WAVES database. If it does not receive an

acknowledgement, it generates an onscreen message
informing you that an acknowledgement was not
received and asking you if you still want to save the
changes made in the WAVES database.

The Wired mode enables you initialize the CRLU and field
transceivers. It is the only mode in which you can set Unit IDs
(see Chapter 6) and update a transceiver’s software version (see
Appendix A).

The On-line and Wired modes operate at 19,200 bps.

Table 2-1. Operating Modes Permission Table

Operation User Off-line On-line Wired
Mode Mode Mode Mode
Press To Talk + - + -
Send Audio Visual Message + - + -
Send text to remote device + - + -
Change audio parameters + + + +*
Monitor units (I/O) + - + -
Peep units internal parameters + - + +
Verify database parameters with actual + - + +
unit parameters
Open link + - + -
Disable link + - + -
Save current settings + + + +
Emergency (+ confirmation) + - + -
Activate the scheduler - + + +*
Open file - + + +
Create new file - + + +
Exit program + + + +
Copy unit - + + +
Cut unit - + + +
Paste unit - + + +

WAVES Installation and Operation Manual 4-7

Installing the WAVES Software

Operation User Off-line On-line Wired

Mode Mode Mode Mode
View/change unit properties (except of - + + +
ID)
Change unit’s ID - +* - +
Activate the WACOL shell - + + +
Generate system’s condition report + + + +
Change unit’s view + + + +
Rename unit - + + +
Activate Tools (Add – On) - + + +
Changing window view options + + + +
Set/Reset background picture - + + +
Send database to unit - - + +
Update all - - + + **
Update version - - - +
Activate statistics and debugger - - - +
+ permitted
- not permitted
* in database only
** updates only the direct connected unit

4-8 WAVES Installation and Operation Manual

 Selecting the Operating Mode

³ To change the operating mode:

1. On the Mode menu, click an operating mode.
– or –
click the required operating mode icon (other than User
mode).
The Enter a password dialog box appears.

2. Enter the password (the default is “waves”).

Notes: a) If you change the operating mode to On-line
and the base station PC does not receive signals
from the CRLU, the base station PC
automatically switches the operating mode to
Off-line. See Appendix B for troubleshooting
suggestions.
b) When the CRLU resumes its transmissions,
the CNU switches automatically to On-line
mode.

WAVES Installation and Operation Manual 4-9

Installing the WAVES Software

³ To change the password:

1. When working in any of the modes (except User mode),
from the Commands menu, select Change Password.
The Change Password dialog box appears.

2. Enter the old password.

3. Enter the new password.
4. Enter again the new password, and click OK.

4.5 CLOSING THE WAVES SOFTWARE

³ To close the WAVES software:
1. On the File menu, click Exit.
The Close File dialog box opens.
2. Click Yes to save changes made to the file.
The WAVES software closes.

4-10 WAVES Installation and Operation Manual

CHAPTER 5

CREATING WAVES
DATABASE

This chapter includes the following sections:

x Understanding how is the site tree is organized
x Viewing the site from the site tree
x Building the site tree
x Using Background Pictures

WAVES Installation and Operation Manual 5-1

Creating WAVES Database

5.1 UNDERSTANDING HOW IS THE SITE TREE

IS ORGANIZED
The site tree is organized in a hierarchical tree format, in which
the higher branches of the tree represent general areas and the
lower branches becoming more specific. It is located on the left
side of the Units window.

Figure 5-1 Site Tree

Note: All the operations described in this chapter are in off-

line mode.

The highest branch of the site tree represents the entire site. The
default site name is Theater. You can change it to a more
appropriate name. In Figure 5-1 the site name has been changed
to Convention Center.

The different areas of the site are represented by the site

elements: zones, sub-zones and units.

The zone and sub-zone branches appear below the site branch.
For example, in Figure 5-1, Main is a zone and Meeting Rooms,
Ballrooms and Restaurants are its sub-zones.

The lowest branch on the site tree is the unit. Unit branches can
appear under a zone or sub-zone branch. In Figure 5-1, Lobby
appears under the Main zone branch but Pool appears under the
North sub-zone branch.

5-2 WAVES Installation and Operation Manual

 Viewing the Site from the Site Tree

An icon appears next to each branch to assist in identifying the

branch level.

Site Zone Sub-Zone Unit

Figure 5-2 Site Tree Branch Icons

Note: When working in Off-line or Wired mode, the Unit icon

appears as a green block with a black question mark.

5.2 VIEWING THE SITE FROM THE SITE TREE

You can use the site tree to display the entire site or focus on
one specific area of the site.

When you open a WAVES file, WAVES displays the site and
zone branches. If you are working with a large site that contains
many site elements, you may need to expand or collapse
branches to obtain a general view of the site tree or focus on a
specific branch. For example, you can view all the zones on the
site tree by collapsing the branches under them or you can open
all the branches under a specific zone.

A + sign to the left of a branch icon indicates that the branch

contains collapsed branches. A  sign indicates that the branch
has sub-branches and all the branches immediately under it are
open. For example, all branches immediately under the Main
branch in Figure 5-3 are open and branches under the Meeting
Rooms, Ballroom and Restaurant branches are hidden. Lobby
and Indoor Pool do not have branches under them.

Figure 5-3 Expanded and Collapsed Branches

WAVES Installation and Operation Manual 5-3

Creating WAVES Database

³ To expand a branch:
x Double-click the branch name.
Or
Click the + sign to the left of the branch icon.

³ To collapse a branch:
x Double-click the branch name.
Or
Click the - sign to the left of the branch icon.

You can also view the details of a branch and the branches
immediately under it in a table format on the right side of the
Units window. Details include the branch name, address and
type.

³ To view branch details:

1. Click a branch.
2. On the View menu, point to Units and Icons and then
click Details.
The branch details appear in table format on the right
side of the Units window.

5-4 WAVES Installation and Operation Manual

 Building the Site Tree

5.3 BUILDING THE SITE TREE

The site database is stored in a WAVES file. To build the site
tree, you must first create a new WAVES file.

Note: All operations defined in this section can be performed

in any mode except User mode.

5.3.1 CREATING A NEW WAVES FILE (.WVS)

³ To create a new WAVES file:
x On the File menu, click New.
The Units and Volume/Mute Control (see Chapter 6)
windows for the new WAVES file appear.

The site tree appears on the left side of the Units window.
WAVES assigns the default site name, Theater, to the site. You
can change it to a more appropriate name, especially if you have
more than one site.

WAVES Installation and Operation Manual 5-5

Creating WAVES Database

5.3.2 OPENING AN EXISTING WAVES FILE

To begin a new work session or switch to a different file that
contains the site tree, you must open an existing WAVES file.

³ To open an existing WAVES file:

1. On the File menu, click Open.
2. In the Open a File dialog box, locate the file.
3. Click Open.
The Units and Volume/Mute Control (see Chapter 6)
windows appear.

5.3.3 DEFINING THE ELEMENTS IN A SITE

Zones, sub-zones and units are site elements. They represent the
different branches of the site tree:
x Zones appear on the level just below the site name. You can
define up to 64 zones.
x Sub-zones appear immediately below zones. You can
define up to 16 sub-zones under each zone.
x Units appear on the lowest level of the site tree. If you do not
need a sub-zone, you can define the unit directly under the
zone. You can define up to 64 units under a zone or sub-zone.

Note: You can place up to 16,384 units in a tree structure

containing 65,536 potential addresses.

When you define a site element, WAVES automatically assigns

it an address number according to a strict numeric hierarchy:
x The address number assigned to the first zone in a site is 1.
x The address number assigned to the third sub-zone of a
zone is 3.
x The address number assigned to the fifth unit of a sub-zone
is 5.

5-6 WAVES Installation and Operation Manual

 Building the Site Tree

The site element address consists of the address number of the

zone followed by the address numbers of the sub-zone and unit:
x The address of the first zone in a site is 1.0.0.
x The address of the third sub-zone of zone 1 is 1.3.0.
x The address of the fifth unit of sub-zone 3 in zone 1 is
1.3.5.

Figure 5-4 shows how the WAVES addressing system works.

SITE TREE ADDRESS

1.0.0
1.1.0
1.1.1
1.1.2
1.2.0
1.2.1

5.0.0

5.7.0

5.7.2

Figure 5-4 WAVES Addressing Method

³ To define a zone:
1. Click the site name.
2. Do one of the following:
x Press INSERT and ENTER.
x Click the right mouse button and then click New.
WAVES opens a new zone and assigns an address
number.

WAVES Installation and Operation Manual 5-7

Creating WAVES Database

³ To define a sub-zone or unit:

1. Click a zone or sub-zone.
2. Do one of the following:
x Press INSERT.
x Click the right mouse button and then click New.
The Select Type dialog box opens.

3. Click Unit or Sub-Zone.

WAVES opens a new unit or sub-zone and assigns an
address number.

5.3.4 RENAMING THE SITE AND ITS ELEMENTS

When you create a new site or site element, WAVES
automatically assigns default names. You can change the
default names to more appropriate ones any time you want to.

³ To rename a site or site element:

1. Click the site or site element.
2. Do one of the following:
x On the Edit menu, click Rename.
x Press F2.
x Click the right mouse button and then click
Rename.
3. Type the new name.
4. Press ENTER.

5-8 WAVES Installation and Operation Manual

 Building the Site Tree

5.3.5 DELETING A SITE ELEMENT

You can delete any site element but not the site itself.

When you delete a site element, you also delete all the site
elements under it. For example, if you delete North in Figure 5-,
you also delete Pool and Tennis Courts.

Note: To delete a site, you must delete the file from your hard
disk.

³ To delete a site element:

1. On the site tree, click the site element you want to
delete.
2. Do one of the following:
x On the Edit menu, click Delete.
x Click the right mouse button and then click Delete.
The Delete Site dialog box opens.
3. Click Yes to delete.
WAVES deletes the site element and all site elements
under it.

5.3.6 REORGANIZING THE SITE TREE

You can easily reorganize the unit groupings on your site tree
and add new site elements by moving or copying sub-zones and
units.

Changing the location of a sub-zone or unit on the site tree

changes unit addresses because WAVES automatically assigns
new addresses based on the site tree hierarchy.

Note: When you copy a sub-zone or unit, the parameters of all

the units are duplicated. Only the addresses for the
duplicated units are different.

If you reorganize the site tree in Off-line mode and save the
new addresses in the base station PC database, you must later
update the field transceivers in On-line mode to maintain the
integrity of the site tree.

WAVES Installation and Operation Manual 5-9

Creating WAVES Database

³ To move a sub-zone or unit:

1. Click the sub-zone or unit you want to move.
2. Drag the sub-zone or unit to the desired new location.
The Move Site dialog box opens.
3. Click Yes.
The sub-zone or unit appears in the new location.
WAVES assigns new addresses to the sub-zone and all
its units or to the unit.

Note: If you are working in Off-line mode, WAVES

issues a message informing you that the new
unit addresses were not sent to the
corresponding field transceivers and asks you if
you want to save them in the WAVES database.

³ To copy a sub-zone or unit:

1. Click the sub-zone or unit you want to copy.
2. On the Edit menu, click Copy.
3. Click the zone or sub-zone under which you want to place
the duplicate.
4. Click Paste.
The Copy Site dialog box opens.
5. Click Yes.
The duplicated sub-zone or unit appears in the new
location. WAVES assigns new addresses to the sub-zone
and all its units or to the unit.

³ To update the field transceivers:

1. If you are in Off-line mode, click On-line on the Mode
menu to change to the On-line mode.
2. Click the unit.
3. On the Commands menu, click DB to Unit.

5-10 WAVES Installation and Operation Manual

 Building the Site Tree

5.3.7 SAVING A WAVES FILE

After building the site tree, save the file for use at a later time.

³ To save the WAVES file:

1. On the File menu, click Save.
The Save A File dialog box opens.
2. Type the name of the file.
3. Click Save.
WAVES saves the file with the .wvs extension.

5.3.8 MAINTAINING DIFFERENT UNIT SETTINGS

You can maintain different sets of parameters for each unit in
the site by saving them to different WAVES files.

For example, you may be responsible for the efficient operation

of a stadium, in which one day a concert may take place and the
next day a sports event. Both types of events could require very
different unit groupings and audio settings.

You can build a site tree containing all the transceivers currently
located in the stadium and save it in different WAVES files. You
can then open one of the WAVES files and rearrange the units into
different groups and with audio settings appropriate to a concert.
Later you can open another WAVES file and rearrange the units
into groups and with audio settings appropriate to a football
game.

Note: Make sure the internal settings and unit ID (see

Chapter 6) of each unit remains the same.

³ To copy the site tree to a new file:

1. On the File menu, click Save As.
The Save As dialog box opens.
2. Type the name of the new file.
3. Click Save.
WAVES copies the contents of the original file into the
new file and saves it with the .wvs extension.

WAVES Installation and Operation Manual 5-11

Creating WAVES Database

³ To change the field transceivers’ current

parameters by applying parameters stored in a
different WAVES file:
1. Close the current WAVES file.
2. Open the WAVES file containing the desired unit
parameters.
3. Update the field transceivers.

³ To update the field transceivers:

1. If you are in Off-line mode, click On-line on the Mode
menu to change to the On-line mode.
2. On the Commands menu, click Update All.
Or
On the File menu, click Open and then select the Update
the Units According to the File check box on the Open
a File dialog box.

5.3.9 CLOSING A WAVES FILE

At the end of the work session, close the file for use at a later
time.

³ To close a WAVES file:

x On the File menu, click Exit.
WAVES closes the file and the Units window.

5-12 WAVES Installation and Operation Manual

 Using Background Pictures

5.4 USING BACKGROUND PICTURES

You can insert a photograph or map of the site or site elements
on the right side of the Units window. You can also build a
visual representation of the site tree by placing buttons
representing site elements on the photographs or maps.

Note: All the operations defined in this section can be

performed in any mode except User mode.

5.4.1 PREPARING BACKGROUND PICTURES

A photograph or map of the site should show the entire site. A
photograph or map of a zone or sub-zone should show more
details. Figure 5-5 presents a small-scale map of an entire site
and a blow-up of the lower left section of the site map.

Save all photographs and maps as bitmap files with the .bmp
extension.

Figure 5-5 Site and Zone Maps

WAVES Installation and Operation Manual 5-13

Creating WAVES Database

5.4.2 INSERTING BACKGROUND PICTURES

³ To insert a background picture:
1. Click a site or a site element on the site tree.
2. On the View menu, point to Units and click Map View.
3. On the Design menu, click Set Background Picture.
4. In the Open dialog box, find the appropriate bitmap
(.bmp) file and click Open.

WAVES inserts the picture into the right side of the

Units window. If the picture is too large to fit into the
allotted space, scroll bars appear to the right and/or
bottom of the right side of the Units window.

5-14 WAVES Installation and Operation Manual

 Using Background Pictures

5.4.3 VIEWING BACKGROUND PICTURES

³ To display a background picture:
1. Click the site or a site element on the site tree.
2. On the View menu, point to Units and click Map View.
WAVES displays the background picture on the right side
of the Units window.

³ To zoom in and out of a background picture:

1. Click the site or a site element on the site tree.
2. Do one of the following:
x On the View menu, point to Zoom and click a
zooming option.
x Click the right mouse button and then click a zooming
option.
Depending on the option you selected, WAVES zooms
in or out of the background picture.
3. If you zoomed in on the background picture, use the
scroll bars to view sections of the picture hidden from
view.

5.4.4 MARKING BACKGROUND PICTURES

You can mark locations on the background picture with
functioning buttons. For example, you can place buttons
indicating zones and
sub-zones on the background picture of the site or you can place
buttons indicating sub-zones and units on the background
picture of a zone.

³ To place a button on a background picture:

1. Click the site or a site element on the site tree.
2. On the View menu, point to Units and click Map View.
WAVES displays the background picture of the selected
site or site element on the right side of the Units window.

WAVES Installation and Operation Manual 5-15

Creating WAVES Database

3. Point to the background picture, click the right mouse

button and select New.
The Select Site Address dialog box opens.

4. Click a site element on the site tree displayed in the

Select Site Address dialog box. You can expand or
collapse branches to locate the site element.

5. Click OK.
A button containing the site element’s name appears in
the upper left corner of the background picture.
6. Drag the button to the location you want to mark on the
background picture.
7. If required, resize the button by dragging its handles.

5-16 WAVES Installation and Operation Manual

 Using Background Pictures

³ To rename or change the appearance of a button:

1. Click the button.
2. Do one of the following:
x On the Edit menu, click Rename.
x On the Edit menu, click Properties and then click
Appearance.
x Click the right mouse button and click Rename.
The Appearance dialog box opens.

3. Type a new name in the Name box and/or select the

appropriate options to change the appearance of the
button.
4. Click Apply to save the new button parameters and
then click OK to close the Appearance dialog box.

WAVES Installation and Operation Manual 5-17

Creating WAVES Database

³ To delete a button on a background picture:

1. Click the button.
2. Do one of the following:
x On the Edit menu, click Delete.
x Click the right mouse button and click Delete.
The Delete Location dialog box opens.
3. Click OK to delete the button.

5.4.5 USING THE BACKGROUND PICTURE BUTTONS

A button placed on a background picture does more than
identify the location of a site element on the picture. You can
use the button to locate a site element on the site tree and
change its parameters.

³ To locate the site element on the site tree:

x Double-click the button representing the site element
you want to locate on the site tree.
WAVES highlights the site element on the site tree.

³ To change site element parameters:

1. Click the button representing the site element you want
to modify.
2. Do one of the following:
x On the Edit menu, click Properties.
x Click the right mouse button and then click
Properties.
The Properties dialog box opens with an additional
tab: Appearance. The site element name appears in the
Title bar.
3. Click a tab and change the site element parameters (see
Chapter 6).

5-18 WAVES Installation and Operation Manual

CHAPTER 6

SETTING PROPERTIES

This chapter includes the following sections:

x General
x Audio properties
x Visual display properties
x I/O control parameters
x BIT parameters
x Unit ID
x Internal parameters
x Site properties
x Database printout

WAVES Installation and Operation Manual 6-1

Setting Properties

6.1 GENERAL
All transceivers are identical when they leave the factory. You
must give each unit a unique identity by configuring:
x Audio properties
x Visual display properties
x I/O control parameters
x BIT parameters
x Unit ID
x Internal parameters
x Site properties

Notes: Unless specified otherwise, you can only set the

properties of a specific unit.

6.2 AUDIO PROPERTIES

You can change the volume, bass and treble settings of a
transceiver.

WAVES differentiates between audio and voice. Audio refers to

inputs connected to ChA and ChB on the ADU-301. Voice
refers to input from the microphone, PC sound card or intercom
ICM-501B. This differentiation enables you to set different
volume levels for audio and voice announcements.

Changing the audio properties of a transceiver at the unit level

changes the settings for that transceiver only. You can set the
audio levels in a range of 0 to 55dB.

Changing the audio properties of the site, zone or sub-zone

branches affects the settings of all the transceivers located under
those branches. Change the audio properties of the transceivers
by indicating an adjustment level in the range of -15 to +15dB.
For example, if the voice volume on Unit 1 is set to 40dB and
you set the voice volume of the site to -5dB, Unit 1 broadcasts
voice announcements at a volume of 35dB.

6-2 WAVES Installation and Operation Manual

 Audio Properties

You can change the audio properties of a transceiver using the

Audio tab of the Properties dialog box or the Volume/Mute
Control window.

Note: All changes made to the audio properties of a

transceiver on the Audio tab of the Properties dialog
box are automatically reflected in the Volume/Mute
Control window. Conversely, all changes made to the
audio properties of a transceiver on the Volume/Mute
Control window are automatically reflected on the
Audio tab of the Properties dialog box.

6.2.1 USING THE PROPERTIES DIALOG BOX

³ To change the audio properties of a unit:
1. Click a unit on the site tree.
2. Do one of the following:
x On the Edit menu, click Properties.
x Click the right mouse button and then click
Properties.
The Properties dialog box opens. The name of the
selected unit appears on the Title bar.
3. Click the Audio tab.

WAVES Installation and Operation Manual 6-3

Setting Properties

Channels I and II refer to the audio output of the unit.

4. Do one of the following:
x Drag the sliders to change settings.
x Point to the value at the bottom of a slider, type a
new value in the box that appears, and click.
x Click the mute check box of a channel to enable or
disable the mute setting for that channel.
x Click Load Defaults to use the default settings.
5. If you want to save the new settings as the default
settings, click Set as Default.
6. Under Power up from, click Last to restore the most
recent audio settings when the field transceiver is
turned on or Default to restore the default settings.
7. Click Apply to send the settings to the transceiver and
save them in the base station PC database.

6-4 WAVES Installation and Operation Manual

 Audio Properties

8. Click OK to send the settings to the transceiver, save

them in the base station PC database and close the
Properties dialog box.

Note: Bass and treble audio setting for Audio Channels I

and II are automatically applied to Voice Channels
I and II.

³ To change the audio properties of a site, zone or sub-

zone:
1. Click the site, a zone or a sub-zone on the site tree.
2. Do one of the following:
x On the Edit menu, click Properties.
x Click the right mouse button and then click
Properties.
The Properties dialog box opens. The name of the site or
the selected zone or sub-zone appears on the Title bar.
3. Click the Audio tab.

WAVES Installation and Operation Manual 6-5

Setting Properties

Channels I and II refer to the audio output of the unit.

4. Do one of the following:
x Drag the sliders to set the amount by which WAVES
should adjust the audio settings of all transceivers
located under the branch.
x Point to the value at the bottom of a slider, type a
new value in the box that appears and click.
x Click a slider and press the UP ARROW and DOWN
ARROW keys to adjust the volume.

5. Click Apply to send the settings to the transceivers and

save them in the base station PC database.
6. Click OK to send the settings to the transceivers, save
them in the base station PC database and close the
Properties dialog box.

6-6 WAVES Installation and Operation Manual

 Audio Properties

6.2.2 USING THE VOLUME/MUTE CONTROL WINDOW

The Volume/Mute Control window automatically appears on
the main window when you open a WAVES file. It graphically
presents the current audio properties of the transceivers on the
site, zone, sub-zone and unit levels of the site tree.

Sizing buttons for the site, zone

and sub-zone levels

Zone Scroll Bar

Figure 6-1 Volume/Mute Control Window

Scroll bars appear below the site and each zone and sub-zone to
help you locate a specific site element on the Volume/Mute
Control site tree.

To facilitate viewing the Volume/Mute Control site tree, you can

adjust the width of the site or any zone or sub-zone by dragging
the sizing button that appears on the upper right corner of the site,
zone or sub-zone.

If you are working with a large site, you can expand or collapse
the site or any site element on the Volume/Mute Control site tree.

³ To expand or collapse the site or any site element:

x Click the site or site element’s name.

WAVES Installation and Operation Manual 6-7

Setting Properties

Using the Volume/Mute Control window, you can change the

volume settings of the audio and voice channels of a transceiver
on the unit level or set the amount by which the volume of all
transceivers in a site, zone or sub-zone are adjusted.

The audio and voice channels appear as colored sliders:

Green - Audio Channel I
Red - Audio Channel II
Yellow - Voice Channel I
Blue - Voice Channel II

³ To change the volume settings of a unit:

1. Click a colored slider.
A large slider appears over the colored slider. The
channel type and volume settings appear to the right of
the slider.
2. Drag the slider to change the volume settings.

³ To change the volume settings of units in a site, zone

or sub-zone:
1. Click a colored slider.
A large slider appears over the colored slider. The
channel type and volume adjustment level appear to the
right of the slider.
2. Drag the slider to set the amount by which WAVES
should adjust the volume settings of all transceivers in
the site or all transceivers located under a specific zone
or sub-zone.

Using the Volume/Mute Control window, you can also define

the mute state for each audio and voice channel. The mute state
is graphically indicated below the colored sliders on the site,
zone, sub-zone and unit levels.

6-8 WAVES Installation and Operation Manual

 Audio Properties

WAVES recognizes the following mute states:

Unmute
Olive green wave on a black field.
Mute
Red horizontal line on a black field.
Unmute Lock
Black wave on a bright green field.
Only appears on the unit level. Indicates that the
audio or voice channel under which it appears is
locked into the unmute state. Changing the mute
status on the site, zone or sub-zone level does not
affect the unmute status of the unit.
Mute Lock
Black horizontal line on a red field.
Only appears on the unit level. Indicates that the
audio or voice channel under which it appears is
locked into the mute state. Changing the mute
status on the site, zone or sub-zone level does not
affect the mute status of the unit.

You can define the mute state of the transceivers by selecting

one of the above mute states or selecting the following
condition:
Don’t Care
Black square on a gray field.
Only appears on the site, zone and sub-zone
levels. Indicates that the mute settings on the unit
level of the site, zone or sub-zone are in effect.

³ To change the site, zone, sub-zone or unit’s mute

state:
1. Click the graphic mute indicator under the slider
representing the channel whose current mute state you
want to change.
2. Click a mute state.
The selected mute state’s graphic representation
appears.

Note: When you define a mute state for a branch of the

Volume/Mute Control site tree, all site elements under

WAVES Installation and Operation Manual 6-9

Setting Properties

that branch are affected unless they are locked. If you

later change the mute state of a site element under the
branch, the new state takes affect for that site element.

6.3 VISUAL DISPLAY PROPERTIES

Since WAVES can support more than one type of visual display
sign, you must define the drivers in the base station PC and the
transceiver’s database by:
a. Installing in the base station PC database all the driver
protocols of visual display signs connected to the field
transceivers
b. Defining the driver and baud rate for each transceiver to
which a visual display sign has been connected
c. Editing each AVM message with the applicable driver
protocol effects (see Chapter 8)

WAVES provides display drivers as .rdd files in the WAVES

folder. You can install the display drivers using the Display tab
of the Properties dialog box or the AVM dialog box (see
Chapter 8).

³ To install a display driver:

1. Click a unit on the site tree.
2. Do one of the following:
x On the Edit menu, click Properties.
x Click the right mouse button and then click
Properties.
The Properties dialog box opens. The name of the
selected unit appears on the Title bar.
3. Click the Display tab.

6-10 WAVES Installation and Operation Manual

 Visual Display Properties

4. Click Drivers.
The Remote Display Drivers dialog box opens.
5. Click Install New Driver.
The Open dialog box appears.
6. Type or locate a filename and click Open.
The Open dialog box closes and the selected driver’s
name appears in the list of drivers on the Remote
Display Drivers dialog box.
7. Click Close.

WAVES Installation and Operation Manual 6-11

Setting Properties

³ To set visual display properties:

1. Click a unit on the site tree.
2. Do one of the following:
x On the Edit menu, click Properties.
x Click the right mouse button and then click
Properties.
The Properties dialog box opens. The name of the
selected unit appears on the Title bar.
3. Click the Display tab.
4. If the unit is not connected to a visual display sign,
select No Output Device.
5. If the unit is connected to a visual display sign that does
not use a protocol supported by WAVES, select
RAW/ASCII Output.
6. If the unit is connected to a visual display that uses a
protocol supported by WAVES, select Other Output
Devices.
7. Under External Device Baud Rate, select the
appropriate baud rate.

Note: 1200 bps Boudrate is applicable only for short

messages (up to 18 bytes).
8. Click Apply to send the new settings to the transceiver.
9. Click Update the Unit to send all the settings in the
Properties dialog box to the transceiver.
10. Click OK to send the new settings to the transceiver
and close the Properties dialog box.

6-12 WAVES Installation and Operation Manual

 I/O Control Parameters

Note: If you are working in On-line mode, the settings

are saved in the base station PC database after
an acknowledgment is received.
If you are working in Off-line mode, a message
appears informing you that the new external
device properties were not sent to the field
transceiver, and asking you if you want to save
the properties in the WAVES database.
If you click Yes, the new settings are stored in
the base station PC’s database. Later you must
update the field transceiver by switching to the
On-line mode and sending these properties to
the unit manually.

6.4 I/O CONTROL PARAMETERS

You can monitor and control conditions on your site from the
base station by attaching external devices to the input and
output pins of field transceivers at key locations throughout
your site and configuring the pins.

For example, if your site contains fire hazards, you can attach a
sensor to a transceiver’s analog input pin that measures
temperature and set the permitted temperature range, and/or you
can attach a smoke detector to a digital input pin. You can also
attach a sprinkler to a digital output pin to turn on the sprinkler
when activated.

Each field transceiver is equipped with one analog input pin,

one digital input pin and two digital I/O pins. You can activate
and configure one or all of these pins on the I/O Settings tab of
the Properties dialog box.

If you attached an external device to the analog input pin, the

transceiver samples the voltage on the pin and digitizes the
information received. You can determine the correct range by
first setting the maximum and minimum values of your device
(see the device’s user manual) and then set the maximum and
minimum correct values.

If you attached an external device to a digital input pin and the

ground pin, the field transceiver receives a high (5V) or low
(0V) signal from the external device. If you attached an external

WAVES Installation and Operation Manual 6-13

Setting Properties

device to a digital output pin and the ground pin, the field
transceiver sends a high (5V) or low (0V) signal to the external
device.

Attaching external devices to the analog and digital input pins

and configuring the pins enables the field transceiver to send
status messages to the PC via the CRLU at a defined BIT rate.
WAVES presents information received in the Site Monitor (see
Section 6.4.2). Using the Site Monitor, you can monitor
conditions at the field transceiver’s location and activate the
digital output pin if it has been configured.

All the digital and analog pins are located on the field
transceiver’s J2 connector.

Figure 6-2 J2 Connector

The J2 connector is configured as follows:
Pins 1 - 5 Audio line output pins used to connect an
external audio amplifier. Pin 3 is the ground pin.
Pin 6 - 10 Analog and digital I/O pins used to connect
external devices. Represented on the I/O tab of
the Properties dialog box as follows:
Pin 6 Analog Input (0-10V)
Pin 7 Reserved for future use
Pin 8 Digital I/O 3 (0-5V)
Pin 9 Digital I/O 2 (0-5V)
Pin 10 Digital Input 1 (0-5V)
Pin 11 +15V pin used to supply DC voltage to external
devices.

Using the I/O Settings tab of the Properties dialog box, you can
also program WAVES to activate a WACOL procedure (see
Section 9.1) when the analog pin’s correct range is breached or
a digital input pin receives a low signal. For example, you can
program WAVES to broadcast an evacuation announcement to a
specific location when it receives a status report from a field
transceiver that indicates smoke detection.

6-14 WAVES Installation and Operation Manual

 I/O Control Parameters

6.4.1 CONFIGURING THE ANALOG AND DIGITAL PINS

³ To configure a transceiver’s analog and digital
pins:
1. Click a unit on the site tree.
2. Do one of the following:
x On the Edit menu, click Properties.
x Click the right mouse button and then click
Properties.
The Properties dialog box opens. The name of the
selected unit appears on the Title bar.
3. Click the I/O Settings tab.

4. Select Monitor I/O on this Unit.

5. Under Analog Input, Select Active to activate the
analog pin.

WAVES Installation and Operation Manual 6-15

Setting Properties

6. Type a descriptive name in the Name box and the

relevant values in the Value Range and Correct Range
boxes.
7. Under Digital Input 1, select Active to activate the
digital input pin, and type a descriptive name in the
Name box.
8. Under Digital I/O 2, select In to activate the digital pin
as an input or Out to activate it as an output, and then
type a descriptive name in the Name box.
9. Repeat Step 8 for Digital I/O 3.
10. If required, type a WACOL command in the
Command box under each activated analog or digital
pin.

Note: When a value falls outside the correct value

range for the analog pin or a digital input pin is
grounded, WAVES performs the WACOL
command according to the BIT Report Rate.
11. Click Apply to send the new settings to the transceiver.
12. Click Update the Unit to send all the settings in the
Properties dialog box to the transceiver.
13. Click OK to send the new settings to the transceiver
and close the Properties dialog box.
Note: If you are working in On-line mode, the settings are
saved in the base station PC database after an
acknowledgment is received.
If you are working in Off-line mode, a message
appears informing you that the SMT packet was not
sent to the field transceiver and asking you if you
want to save the properties in the WAVES database.
If you click Yes, the new settings are stored in the
base station PC’s database. Later you must update
the field transceiver by switching to the On-line
mode and send these properties to the unit
manually.

6-16 WAVES Installation and Operation Manual

 I/O Control Parameters

6.4.1.1 Prioritizing Messages

The normal sampling rate is based on the Report Rate defined
in the BIT tab of the Properties dialog box (see Section 6.4.3).

If an input is assigned an emergency priority, the transceiver

overrides the Report Rate and sends a status message
immediately to the CRLU.

Emergency status messages share the bandwidth of an existing

link between the CRLU and any field transceiver (see Chapter
10) while normal status messages are blocked.

You can assign emergency priority to one or all of the analog

and digital inputs.

WARNING: Although you can assign emergency priority to

Digital I/O 3, the emergency priority does not
function in the current version.

³ To assign emergency priority to an analog or

digital input:
x On the I/O Settings tab, select Emergency Priority in
the analog or digital input’s area.

6.4.2 USING THE SITE MONITOR

If you programmed a field transceiver to send status messages
to the base station PC via the CRLU, you can monitor the site
conditions of the transceiver from the base.

WAVES Installation and Operation Manual 6-17

Setting Properties

³ To monitor a transceiver’s site conditions:

1. Click a unit on the site tree.
2. On the Commands menu, click Monitor.
The Status Monitor opens.

The name assigned to an active analog input or digital

I/O pin appears above its graphic representation.
A scale appears below the analog input’s name with
green indicating the correct value range, blue indicating
the acceptable lower value range and red indicating the
acceptable upper value range. A black indicator shows
the current voltage and the value of the current voltage
appears below the scale. If the current voltage falls
outside the correct value range, the WACOL command
for the analog input is activated if configured on the I/O
Settings tab of the Properties dialog box.
A light appears below each digital input’s name. If the
digital input receives a low signal, the light below its
name turns red and the WACOL command for the
digital input is activated if configured on the I/O
Settings tab of the Properties dialog box.
A switch appears below each digital output’s name. If
the switch is turned On, the output is 5V and if the
switch is turned Off, the output is grounded.
3. Click the switch to enable or disable the output pin.

6.4.3 CONFIGURING THE ANALOG REPORT PARAMETERS

You can use the analog input pin 6 of J2 for a number of
reports. For example, if you have an analog device that its
output voltage is between 0Vdc to 10Vdc while the normal
range is 5Vdc to 10Vdc, you can configure the analog input to
report any changes from the normal range.

6-18 WAVES Installation and Operation Manual

 I/O Control Parameters

The input voltage is digitized to the range 0 to 255. 0 represents

0 Vdc, and 255 represents 10 Vdc. You can define up to 32
voltage ranges and set a name for each range. When the input
voltage is within a range that is not a normal range, the system
initiates a specific report for that defined range.

Note: The analog division procedure is applicable for the

entire site.

Configuration of the analog report parameters is divided to

three steps:
1. Connect the analog output of your device to connector J2
pin 6 of the unit.
2. Define the ranges that represent the analog input (see the
following procedure).
3. Set the WACOL command “reportanalog” in I/O settings
tab for the selected unit. This command is activated when
the analog input exceeds the normal range (see the
following procedure).
4. In Report Filter table, select the Report check box for the
category Monitor (see section 6.8.6 Defining Report Filter
Table).

³ To define the analog input ranges:

1. On the File menu, click Properties.
The Site Properties dialog box opens with the site
name on the Title bar.
2. Click the Analog Division tab.

WAVES Installation and Operation Manual 6-19

Setting Properties

3. In the Range From and Range To boxes, enter the

range.
4. In the Name box, enter the name for that range and
click the Insert button.
5. Click Apply to store the new settings in the database.
6. Click OK to store the new settings and close the Site
Properties dialog box.

6-20 WAVES Installation and Operation Manual

 I/O Control Parameters

³ To set the WACOL command “reportanalog” in

I/O settings tab for the selected unit:
1. Click a unit on the site tree.
2. Do one of the following:
x On the Edit menu, click Properties.
x Click the right mouse button and then click
Properties.
The Properties dialog box opens. The name of the
selected unit appears on the Title bar.
3. Click the I/O Settings tab.

4. Select Monitor I/O on this Unit.

5. Under Analog Input, select Active to activate the
analog pin.

WAVES Installation and Operation Manual 6-21

Setting Properties

6. Type a descriptive name in the Name box and the

relevant values in the Value Range and Correct Range
boxes. The upper limit of the Value Range and
Correct Range must be 255.
7. Type the WACOL command “reportanalog” in the
Command box under the analog pin.
8. Click Apply to send the new settings to the transceiver.
9. Click Update the Unit to send all the settings in the
Properties dialog box to the transceiver.
10. Click OK to send the new settings to the transceiver
and close the Properties dialog box.

Note: When a value falls below the correct value

range for the analog pin, WAVES performs the
WACOL command and also sends a message
(including the analog division name, unit name
and unit address) to the system condition’s
report window.

6.5 BIT PARAMETERS

Each field transceiver conducts two types of built-in (BIT)
diagnostic tests:
x Power-on-BIT (POB) which tests the hardware
configuration during power on
x Online BIT which tests the system’s operation

Test results are reported at a defined rate or on demand to the

base station. The base station then lists status information,
including errors detected and corrections to errors in its log file.

When the BIT detects an unusual condition, WAVES graphically

indicates the status of the field transceiver on the site tree by
replacing the field transceiver’s normal unit icon with one of the
following special icons:

Red block with a yellow question mark.

The base station did not receive BIT results from
the unit. When the base station tried to contact the
unit, it received no response.

6-22 WAVES Installation and Operation Manual

 BIT Parameters

Yellow loudspeaker with a red “X” across it.

Audio test detected a functional error on the
amplified audio outputs.
Red battery with a red diagonal across it.
BIT detected that the backup battery power supply
is low (has 10V or less)
Blue battery with a yellow lightning sign.
BIT detected that the unit is using its backup battery
Blue battery with a red “X” across it.
BIT detected that the unit does not have a backup
battery even though it is registered as having one.

³ To set the BIT parameters:

1. Click a unit on the site tree.
2. Do one of the following:
x On the Edit menu, click Properties.
x Click the right mouse button and then click
Properties.
The Properties dialog box opens. The name of the
selected unit appears on the Title bar.
3. Click the BIT tab.

WAVES Installation and Operation Manual 6-23

Setting Properties

WAVES indicates the last time the PC received a BIT

message under Last Time Received.
4. In the Report Rate box, click the arrows to change the
rate at which the transceiver sends BIT messages to the
CRLU. The default Report rate is 60 seconds. It is
recommended that you set the rate based on the number
of field transceivers in the site. For example, if you
have 80 field transceivers on the site, set the report rate
to 80 seconds.
5. To check the audio circuit on the field transceiver’s
amplified outputs, select the Perform Audio Test
checkbox and define the interval between tests in
minutes in the Rate box.
Note: If the field transceiver’s audio settings are
lower than the audio threshold required by the
audio test, the audio test generates a sine signal
that may disrupt your audio signal.

6-24 WAVES Installation and Operation Manual

 BIT Parameters

6. To register the field transceiver’s backup battery and

check its status, select the Has Backup Battery
checkbox.
7. To check if the field transceiver is powered by its AC
power supply, select the Has AC Supply checkbox.
8. Click Apply to send the new settings to the transceiver.
9. Click Update the Unit to send all the settings in the
Properties dialog box to the transceiver.
10. Click OK to send the new settings to the transceiver
and close the Properties dialog box.
Note: If you are working in On-line mode, the settings are
saved in the base station PC database after an
acknowledgment is received.
If you are working in Off-line mode, a message
appears informing you that the BIT packet was not
sent to the field transceiver and asking you if you
want to save the properties in the WAVES database.
If you click Yes, the new settings are stored in the
base station PC’s database. Later you must update
the field transceiver by switching to the On-line
mode and sending these properties to the unit
manually.

³ To update the BIT results:

x On the BIT tab of the Properties dialog box, click
Request BIT.

³ To update the Power-On-BIT (POB) results:

x On the BIT tab of the Properties dialog box, click
Request POB.

³ To view the results of the BIT and POB tests:

x On the Command menu, click BIT Result.
The BIT Result Table appears.

WAVES Installation and Operation Manual 6-25

Setting Properties

o
p
q

r
s u
t

The name of the unit appears in the Title bar.

The table summarizes the current online status of the
field transceiver and the POB results.
The following table describes some of the important
fields:
Field Name Description
n Battery Battery Status
0: OK
1: No battery
3: Battery power is low
o Output Level Audio Output Level:
OK/Fail
p RSSI Receive Signal Strength Indicator:
170-255: Good
150-170: Fair
130-150: Marginal
q Miss Correlations Number of packets lost by the receiver (accumulative parameter).
When packets are lost, also Audio CRC fail is incremented. The
ranges are same as in Audio CRC fail. When there are 7
consecutive failures, the receiver starts to search for another
source.
r Source Current RF source:
Primary/Secondary
s Rf agc Receive attenuation status. used for attenuation of strong signals.
On – Receive signal is attenuated
Off – Receive signal is not attenuated

6-26 WAVES Installation and Operation Manual

 Unit ID

t Audio CRC fail Audio CRC failures per second (accumulative parameter):
Good reception – increments of 0 – 2 failures per 10 seconds
Bad reception – increments of more than 20 failures per 10
seconds (the receiver will search for another source)
u Link enable RS-232 link Enable/Disable

³ To restart the Power On Process from the base

station:
1. Click a unit on the site tree.
2. Do one of the following:
x On the Edit menu, click Properties.
x Click the right mouse button and then click
Properties.
The Properties dialog box opens. The name of the
selected unit appears on the Title bar.
3. Click the BIT tab.
4. Click Reboot the Unit.

6.6 UNIT ID
The Unit ID is the transceiver’s physical address. It is used by
WAVES physical and link communication layers to link each
unit to its primary and secondary RF source.

You have to assign a unique number as the Unit ID. You can
assign any number from 0 to 16,383 with the following
exceptions:
x Eight LSB (Least Significant Bits) cannot be 0. Therefore,
the following numbers may not be assigned as the Unit ID:
0, 256, 512, 768, 1024, 1280, 1536, 1792, 2048, 2304,
2560, 2816, 3072, 3328, 3584, 3840,4096, 4352, 4608,
4864, 5120, 5376, 5632, 5888, 6144, 6400, 6656, 6912,
7168, 7424, 7680, 7936, 8192, 8448, 8704, 8960, 9216,
9472, 9728, 9984, 10240, 10496, 10752,11008, 11264,
11520, 11776, 12032, 12288, 12544, 12800, 13056, 13312,
13568, 13824, 14080, 14336, 14592, 14848, 15104, 15360,
15616,15872 and 16128.

WAVES Installation and Operation Manual 6-27

Setting Properties

x The transceiver’s link communication layer children

(primary and secondary listeners) cannot have identical
eight LSBs (binary) in their Unit IDs.

You can only assign a Unit ID to a transceiver in Wired mode.

³ To assign a Unit ID to a transceiver:

1. Connect one end of the CAB-PC-ADU-3 cable to the
serial port of your PC and the other end to the RS-232
port of the transceiver.
2. On the Mode menu, click Wired.
3. Click a unit on the site tree.
4. Do one of the following:
x On the Edit menu, click Properties.
x Click the right mouse button and then click
Properties.
The Properties dialog box opens. The name of the
selected unit appears on the Title bar.
5. Click the Unit ID tab.

6-28 WAVES Installation and Operation Manual

 Unit ID

6. Type a number in the Unit ID box.

7. Click Apply to send the new Unit ID to the transceiver.
8. Click Update the Unit to send the Unit ID in the
Properties dialog box to the transceiver.
9. Click OK to send the new Unit ID to the transceiver
and close the Properties dialog box.

Note: If you are working in Wired mode, the settings are

saved in the base station PC database after an
acknowledgment is received.
You cannot assign a Unit ID in On-line mode. You
can assign it in Off-line mode, in which case a
message appears informing you that the ID was not
sent to the field transceiver and asking you if you
want to save it in the WAVES database.
If you click Yes, the new settings are stored in the
base station PC’s database. Later you must update

WAVES Installation and Operation Manual 6-29

Setting Properties

the field transceiver by connecting one end of the

CAB-PC-ADU cable to the serial port of your PC,
and the other end to the RS-232 port of the
transceiver. Then, switch to Wired mode and click
Update the Unit on the Unit ID tab of the
Properties dialog box.

6.7 INTERNAL PARAMETERS

To enable the WAVES software to communicate with the CRLU
and field transceivers, you must set the following parameters for
each unit:
x Unit Type. Defines the unit as a CRLU (transceiver at the
base station), RLX (field receiver), PRLU (field relay) or
SRLU (satellite relay).
x TX Offset. Offset value (0-75) selected by you for the
unit’s forward RF transmissions.
x 1st RX ID. ID number of the primary unit from which this
unit receives RF signals.
x 2nd RX ID. ID number of the secondary (backup) unit
from which this unit receives RF signals.
x 1st RX Offset. TX offset of the primary unit. The unit
needs this offset to lock onto the primary unit’s RF signal.
x 2nd RX Offset. TX offset of the secondary unit. The unit
needs this offset to lock onto the secondary unit’s RF
signal.

Offsets are frequency values assigned by you to a CRLU or a

field transceiver to enable it to recognize which RF signals to
accept and which to ignore. The best numbers to use as offset
values are prime numbers between 0-75 (i.e., 1, 2, 3, 5, 7, 11,
13, 17, 19, 23, 31, 37, 41, 43,47,53,59, 61, 67, 71, 73). For
more information, see Appendix C.

Each field transceiver then hops from frequency to frequency to

locate that frequency defined as the offset of its primary or
secondary unit. It locks on to a specific signal when the
transmitting unit’s Unit ID and TX Offset matches the unit’s
programmed Primary/Secondary RX ID and Offset.

6-30 WAVES Installation and Operation Manual

 Internal Parameters

³ To set the internal parameters of a transceiver:

13. Click a unit on the site tree.
2. Do one of the following:
x On the Edit menu, click Properties.
x Click the right mouse button and then click
Properties.
The Properties dialog box opens. The name of the
selected unit appears on the Title bar.

Note: WAVES application automatically assigns the units

address, and loads it when assigning the internal
parameters.
1. Click the Internal Parameters tab.

2. In the Unit Type list, click the type of unit (CRLU,

RLX, PRLU or SRLU).

WAVES Installation and Operation Manual 6-31

Setting Properties

3. If you select SRLU, the SRLU Audio Source box

appears. Select the audio source, Base for CRLU input
or Local for SRLU input.
4. Under RF Settings, enter the 1st RX ID parameter and
its RX offset.
5. Click Apply to send the new settings to the transceiver.
6. Under RF Settings, enter the 2nd RX ID parameter
and its RX offset.
7. Click Apply to send the new settings to the transceiver.
8. Click Update the Unit to send all the settings in the
Properties dialog box to the transceiver.
9. Click OK to send the new settings to the transceiver
and close the Properties dialog box.

Note: If you are working in On-line mode, the settings are

saved in the base station PC database after an
acknowledgment is received.
If you are working in Off-line mode, a message for
each changed parameter appears informing you
that the change was not sent to the field transceiver
and asking you if you want to save the changes in
the WAVES database.
If you click Yes, the new settings are stored in the
base station PC’s database. Later you must update
the field transceiver by switching to the On-line
mode and sending these properties to the unit
manually (verify the reception of the RF
parameters, and re-sending if necessary).

6-32 WAVES Installation and Operation Manual

 Internal Parameters

6.7.1 USING THE PEEP UNIT INFORMATION MONITOR

Using the Peep Unit Information monitor, you can monitor a
transceiver’s internal parameters

³ To monitor a transceiver’s internal parameters:

1. Click a unit on the site tree.
2. On the Commands menu, click Peep Unit Info.
The Monitor dialog box opens.

Yes, if the unit is

Valid in SRLU connected to the ICM
configuration only (Base
or Local)

³ To close the Monitor dialog box:

x Click Close.

WAVES Installation and Operation Manual 6-33

Setting Properties

6.8 SITE PROPERTIES

The following parameters affect the whole site:
x Emergency
x RS-232
x Log file
x Audio mode
x Audio refresh
x Report filter
x Analog division
(see section 6.4.3 “Configuring the analog report
parameters”).

6.8.1 SETTING THE EMERGENCY PARAMETERS

During an emergency, WAVES overrides all mute settings
(including Mute Lock) on the voice channels and raises the
volume of the voice channels by the number of decibels defined
as the emergency gain. In addition, WAVES executes the
emergency command (defined in the Emergency tab), and the
following message appears on the screen.

When deactivating the emergency mode, WAVES performs the

following:
x Restores the mute settings in unit level.
x Sets the group mute settings to “don’t care”.
x Reduces the volume to the normal setting.
x Executes the “clear command” defined in this tab.

6-34 WAVES Installation and Operation Manual

 Site Properties

³ To set the emergency gain:

1. On the File menu, click Properties.
The Site Properties dialog box opens with the site
name on the Title bar.
2. Click the Emergency tab.

3. In the Emergency Gain text box, type a number in

decibels.
4. In the Emergency Command text box, type a WACOL
command.
5. In the Clear Command text box, type a WACOL
command.
6. Click Apply to save the new parameters.
7. Click OK to save the new parameters and close the Site
Properties dialog box.

WAVES Installation and Operation Manual 6-35

Setting Properties

6.8.2 SETTING THE RS-232 PARAMETERS

You can open a full duplex link between the data device
connected to the RS-232 connector on the CRLU and a data
device connected to the RS-232 connector on a field transceiver
(see Chapter 10).

WAVES automatically closes the link after a defined period of

silence has expired.

³ To set the timeout period:

1. On the File menu, click Properties.
The Site Properties dialog box opens with the site
name on the Title bar.
2. Click the RS-232 tab.

3. In the RS-232 Link Timeout text box, type a number

in measured seconds.

6-36 WAVES Installation and Operation Manual

 Site Properties

4. Click Apply to save the new parameter and send it to

the CRLU.
5. Click OK to save the new parameter, send it to the
CRLU and close the Site Properties dialog box.

6.8.3 DEFINING THE LOG FILE PARAMETERS

WAVES automatically creates a log file. As a security measure,
WAVES does not grant you direct access to the log file.

You can configure WAVES to automatically create a backup file

in a defined location on your hard drive when the log file
exceeds a predefined size. You can access the data in this file.

You can also configure WAVES to save log data covering

defined time periods in a series of files. For example, you can
define a period of 7200 minutes (5 days) and WAVES will save
a series of files, each containing 7200 minutes worth of log data
and identified by the starting time of the data.

Finally, WAVES enables you to print online a hardcopy of the

log file if a printer is connected to the base station PC.

³ To create a backup file in a defined location:

1. On the File menu, click Properties.
The Site Properties dialog box opens with the site
name on the Title bar.
2. Click the Log File Properties tab.

WAVES Installation and Operation Manual 6-37

Setting Properties

3. Select the backup file check box and type a number in

KB in the backup text box.
4. Enter the name of a directory in the text box below the
backup file check box.
5. Click Apply to save the new settings.
6. Click OK to save the new settings and close the Site
Properties dialog box.

³ To create files containing log data for defined

periods of time:
1. On the File menu, click Properties.
The Site Properties dialog box opens with the site
name on the Title bar.
2. Click the Log File Properties tab.

6-38 WAVES Installation and Operation Manual

 Site Properties

3. Select the Save Log File check box and type a number
in minutes in the text box.
Note: You can define a maximum period of 9999
minutes (approximately one week).
4. Enter the name of a directory in the text box below
Save Log File check box.
5. Click Apply to save the new settings.
6. Click OK to save the new settings and close the Site
Properties dialog box.

³ To print on-line a hardcopy of the data in the log

file:
1. On the File menu, click Properties.
The Site Properties dialog box opens with the site
name on the Title bar.
2. Click the Log File Properties tab.
3. Select the Write To check box and type the name of
your printer’s port.
4. Click Apply to save the new settings.
5. Click OK to save the new settings and close the Site
Properties dialog box.

WARNING: Make sure your printer is on-line or

WAVES will go into an extended timeout
period.

6.8.4 DEFINING AUDIO MODE

Audio Mode Defines the type of audio configuration supported
by the unit (valid in version 4.5 only). You can define the audio
type as:
x 64x2 a+voice. If no PTT is sent, or if a PTT is sent on the
forward channel and is not addressed to the unit, Channel A
input is switched to both Channels I and II. If a PTT is sent
on the forward channel and is addressed to the unit, the
voice input (mic, sound card or intercom) is switched to
both Channels I and II.

WAVES Installation and Operation Manual 6-39

Setting Properties

x 64x2 a+b. Outputs Channel A input on Channel I and

Channel B input on Channel II. If a PTT message is sent on
the forward channel and it is addressed to the unit, it
outputs the message on both Channels I and II. If a PTT
message is sent on the forward channel and it is not
addressed to the unit, it mutes the audio outputs.
x 128 mono. Outputs Channel A input on both Channels I and
II in high quality mono sound (wideband). If a PTT
message is sent on the forward channel and it is addressed
to the unit, it outputs the message on both Channels I and II.
If a PTT message is sent on the forward channel and it is
not addressed to the unit, it mutes the audio output.
x 32 mono. Outputs Channel A input on both Channels I and
II in narrow band, mono sound to get better immunity. If a
PTT message is sent on the forward channel and is
addressed to the unit, it outputs the message on both
Channels I and II. If a PTT message is sent on the forward
channel and is not addressed to the unit, it mutes the audio
output.

Note: When changing the audio mode of the CRLU,

the WAVES system will lose synchronization for
approximately one.

³ To define the Audio Refresh interval:

1. On the File menu, click Properties.
The Site Properties dialog box opens with the site
name on the Title bar.
2. Click the Audio Mode tab.

6-40 WAVES Installation and Operation Manual

 Site Properties

3. In the Audio Mode list, click the audio type to be

supported by the site (64x2 a+voice, 64x2 a+b, 128
mono or 32 mono).

Note: Audio type 32 mono is applicable in version 4.5 only.

4. Click Apply to save the new parameter.
5. Click Update all to send all the settings in the
Properties dialog box to the transceiver.
6. Click OK to save the new parameter and close the Site
Properties dialog box.

WAVES Installation and Operation Manual 6-41

Setting Properties

6.8.5 DEFINING AUDIO REFRESH

When in On-line mode, WAVES updates the audio and mute
parameters of each transceiver in the site at defined periods of
time.

For example, if you define an Audio Refresh interval of ten

minutes, WAVES in On-line mode refreshes the audio and mute
parameters of each transceiver every ten minutes.

³ To define the Audio Refresh interval:

1. On the File menu, click Properties.
The Site Properties dialog box opens with the site
name on the Title bar.
2. Click the Audio Refresh tab.

6-42 WAVES Installation and Operation Manual

 Site Properties

3. Select the Audio Refresh check box and type a number

in minutes in the text box.
4. Click Apply to save the new parameter.
5. Click OK to save the new parameter and close the Site
Properties dialog box.

6.8.6 DEFINING REPORT FILTER TABLE

The Report filter table enables you to define for each report
category the following notification types and/or log record:

Report - When selecting Report, the System’s Condition

Report dialog box appears when a failure occurs
(see section “6.8.6.1 Using The System’s Condition
Report Dialog Box”).

Buzzer - When selecting Buzzer, the WACOL command

(written in Buzzer command box) is executed when
a failure occurs.

Hazard - When selecting Hazard, Hazard window appears

when a failure occurs. The Hazard window
continues to appear until it is checked in System’s
Condition Report dialog box.

Note: When selecting Buzzer and/or Hazard, Report is

selected automatically.

Log File - see section “6.8.3 Defining the Log File

Parameters”.

You can also program WAVES to notify the operator with an

on-screen message and/or audio message.

WAVES Installation and Operation Manual 6-43

Setting Properties

The report filter table includes the following categories:

No response – The unit does not respond.
Monitor – Changes in the unit’s analog/digital input.
BIT – BIT error.
Connection error – The CRLU does not respond.
Internal error – Internal software error or PC hardware error.
WACOL error – Error in WACOL script execution.
User error – You performed an illegal operation.
Other – Undefined errors.

³ To define the report filter:

1. On the File menu, click Properties.
The Site Properties dialog box opens with the site
name on the Title bar.
2. Click the Report Filter tab.

6-44 WAVES Installation and Operation Manual

 Site Properties

3. For each category, select the notification type check

box for the manner in which you wish to be notified. If
you selected buzzer, type a buzzer command in the
Buzzer Command box.

Note: If you selected the Report check box in the

Monitor category, you must define the report in
the unit’s I/O settings tab (see “Configuring the
Analog and Digital pins”).
If you select Buzzer or Hazard types, then
Report type is automatically selected.
4. Click Apply to save the new parameters.
5. Click OK to save the new parameters and close the Site
Properties dialog box.

WAVES Installation and Operation Manual 6-45

Setting Properties

6.8.6.1 Using The System’s Condition Report Dialog Box

For each error, the System’s Condition Report dialog box
presents the error type, category, a detailed description and a
suggested course of action.

If an error occurs that requires immediate attention, WAVES

automatically opens the System’s Condition Report dialog box.
You can view log data any time by opening the System’s
Condition Report dialog box.

³ To view log data:

x On the View menu, click System’s Condition Report.
The System’s Condition Report dialog box opens.

Reports are presented in table format. The widths of the

columns are adjustable. To make a column wider or
narrower, drag the column border at the top of the table.

The Name column describes the problem, e.g., “CRLU

does not response from”. In addition, a red dot indicates
that the report is not accepted yet. After clicking the red
dot, it changes its color to green including a check sign.

6-46 WAVES Installation and Operation Manual

 Site Properties

The Category column contains the category of the

report message generated by the problem.

The Description column provides a detailed description

of the problem and suggests a course of action, e.g.,
“CRLU does not response from. Check cable
connection”.

³ To view details of a particular problem:

x On the System’s Condition Report dialog box, click a
problem in the Name column.
A detailed description of the problem and possible
solutions appear in the bottom gray box.

³ To delete all messages:

x On the System’s Condition Report dialog box, click
Clear.

WAVES Installation and Operation Manual 6-47

Setting Properties

6.9 DATABASE PRINTOUT

You can print the database information as a .WVS file. This
information includes the following subjects:
x Units internal settings
x Units design settings and bitmaps
x Units audio settings
x Scheduler events
x Audio visual messages
x Remote device drivers

³ To print the database:

1. On the Commands menu, click Export Data Base.
Export database message appears.
2. Click Yes to export the database to ASCII format
(*.txt).The Save a File dialog box appears.

Note: Never type a name with .WVS extension for a database

report, since you might override the existing database
file.
3. Enter the file name and click Save.
4. Open the ASCII file with an ASCII editor (e.g.
Notepad) and print.

The following is an example for printed database.

6-48 WAVES Installation and Operation Manual

 Database Printout

File Name - C:\file21-9-99.wvs

Units internal settings

_______________________

addr id 1TXId 2TXId 1RXOff 2RXOff TxOff BitR Audio ExtDev

0,0,0
1,0,0
1,0,1 700 0 0 0 0 10 600 ASCII
1,0,2 703 700 701 10 15 2 600 ASCII
2,0,0
2,0,1 700 700 700 10 10 2 600 ASCII
2,0,2 702 701 700 15 10 51 600 ASCII

Units design settings

_____________________

addr Name Bitmap

0,0,0 Theate C:\WIN95B2\Circles.bmp
1,0,0 Zone 1 C:\WIN95B2\Tiles.bmp
1,0,1 Crlu C:\WIN95B2\Waves.bmp
1,0,2 Right C:\WIN95B2\Bubbles.bmp
2,0,0 Zone 2 C:\WIN95B2\Houndstooth.bmp
2,0,1 Srlu C:\WIN95B2\Pinstripe.bmp
2,0,2 Left C:\WIN95B2\Bubbles.bmp

Units audio settings

____________________

addr Vol1 Bass1 Treb1 Mute1 Vol2 Bass2 Treb2 Mute2 VolV1
MuteV1 VolV2 MuteV2
0,0,0 0 0 0 UnM 0 0 0 UnM 0
UnM 0 UnM
1,0,0 0 0 0 UnM 0 0 0 UnM 0
UnM 0 UnM
1,0,1 15 0 0 UnM 15 0 0 UnM 15
UnM 15 UnM
1,0,2 -20 0 0 UnM -20 0 0 UnM -20
UnM -20 UnM
2,0,0 0 0 0 Mute 0 0 0 Mute 15
Mute 0 Mute
2,0,1 0 0 0 Mute 0 0 0 Mute 0
Mute 0 Mute
2,0,2 0 0 0 Mute 0 0 0 Mute 0
Mute 0 Mute

Scheduler Events
________________
Descr Wacol Time
good mor sendavm addr(0,0,0)=2 Wed Sep 22 13:08:38 1999
check report="check",categ=3 Wed Sep 22 13:49:16 1999
good report="good",categ=5 Thu Sep 23 12:49:50 1999
SHLOM SENDAVM ADDR(2,0,1)=5 Fri Oct 22 12:59:42 1999

Audio Visual Messages

_____________________
No Name Audio
5 MERKAVIM C:\Markavim.wav
4 waves C:\madahcom.wav
3 Madah-Com C:\madahcom.wav
2 good-morning C:\good morning.wav
1 emergency C:\emergency.wav

Remote Device Drivers

_____________________
No Name
1 Venus1500 Protocol(New)
2 InfoNet Protocol
3 ComFuture(Ver. 1.1)

WAVES Installation and Operation Manual 6-49

CHAPTER 7

INSTALLING THE WAVES

HARDWARE

This chapter includes the following sections:

x Safety precautions
x Unpacking
x Installing the base station
x Installing the transceivers
x Installing the EMP-111 emergency push button
x Installing EMP-211 wireless remote activator
x Installing LED sign

WAVES Installation and Operation Manual 7-1

Installing the WAVES Hardware

7.1 SAFETY PRECAUTIONS

7.1.1 MECHANICAL
x Install the TRX-401 and CRLU-201 with the connector side
facing down. If you are installing a TRX-401 10 m or more
above the transceiver from which it receives RF signals,
mount the connector side facing up.
x Always operate the TRX-401 and CRLU-201 with their
plastic covers on and secured.
x Make sure that all of the locking screws are in place before
mounting the TRX-401 and CRLU-201.
x Always secure the cable plugs to the units using their
mounting screws.
x Use tie wraps, to secure cables to units.
x If a 14 dBi antenna is installed, make sure no one can come
within 15 cm of it. If a 9 dBi antenna is installed, make sure
no one can come within 8 cm. If a 3 dBi antenna is
installed, make sure no one can come within 4 cm.

7.1.2 ENVIRONMENTAL
x Avoid severe wet conditions.
x Do not operate the units above their specified limits.

7.1.3 ELECTRICAL
x Make sure all electrical connectors are securely installed
before applying power to the units.
x Only use a detachable, 18 AWG min., and flexible power
supply cord with three conductors. One end of the power
supply cord must end in a grounding type attachment plug
with a parallel blade configuration and the other end must
end in an appliance coupler which mates with an appliance
inlet. The maximum cord length is five feet. Following is a
list of safety-approved cable types:

7-2 WAVES Installation and Operation Manual

 Unpacking

CRLU-201/ SVE, SVO, SVOO SVT, SVTO, SVPOO

TRX-401 SP-2, SPE-2, SPT-2, SP-3, SPE-3, SPT-3
SJ, SJE, SJO, SJOO, SJT, SJTO, SJTOO
S, SE, SO, SOO, SOO, ST, STO, STOO

ADU-301 SV, SVE, SVO, SVOO SVT, SVTO,

SVPOO,SP-2, SPE-2, SPT-2, SP-3,
SPE-3, SPT-3, SJ, SJE, SJO, SJOO, SJT,
SJTO, SJTOO, S, SE, SO, SOO, SOO,
ST, STO, STOO
Note: For units shipped outside North America, a suitable
power supply cord set is provided according to
country of designation.
x Do not remove antenna cables while the TRX-401 and
CRLU-201 are powered up. Note that only a MADAH-Com
authorized installer can handle the antenna and antenna
cables.
x Do not short any of the audio outputs to the unit’s case.

Warning Where necessary, provide lightning and electrical

protection.

7.2 UNPACKING
Before unpacking, inspect the package. If you notice any
damage, immediately report it to your local dealer.

³ To unpack the WAVES hardware:

1. Place the package on a flat surface and open it.
2. Remove the contents of the package and place them on
a clean surface.
3. Remove all packing material.
4. Inspect the contents. If you notice any physical damage,
immediately report it to your local dealer.

WAVES Installation and Operation Manual 7-3

Installing the WAVES Hardware

7.3 INSTALLING THE BASE STATION

The base station contains the base transceiver (CRLU-201),
Audio and data interface unit (ADU-301) and an optional
computer.
AD U-301 _ REAR PA NEL
C H A NN E L A L INE IN P U T CH A N N E L B L IN E IN P UT P C S O U ND C A RD D ATA P O RT S SYNC IC M

P E A K C LIP P E A K C LI P IN O UT
PAD PA D R S -2 3 2 to C RL U R S -2 32

TR IM T RIM FR OM TO to C R LU to P C C o ntro l

A C Line In

A nalog and/or digital I/O devices

A m plifier
D evice that uses D C pow er
A lternate base station sw itch

ADU R S-232
J1
11 10 9 8 7 6 5 4 3 2 1
AM P O U T +15V I/O LINE OUT
J4
J2
J6
+1 2VDC

Sp eake rs
J5

A C L in e In

Figure 7-1 Base Station Wiring Diagram

³ To set up the base station:

1. If you want to install the ADU-301 in a standard
equipment rack, use the hooks on the ADU-301’s side
panels to mount it on the rack.
2. Connect one end of the CAB-PC-ADU-3 cable to the
serial port of the optional base station PC and the other
end to the DATA PORTS: TO PC CONTROL
connector on the ADU-301.
3. Connect one end of the CAB-ADU-25/9-CRLU-4 cable
to the DATA PORTS: TO CRLU connector on the
ADU-301 and the other end of the cable to the ADU
connector on the CRLU-201.

7-4 WAVES Installation and Operation Manual

 Installing the Base Station

Figure 7-2 Bottom Panel of the CRLU-201

4. Connect the power cable to the ADU-301 power

connector on the rear panel.

Figure 7-3 Rear Panel of the ADU-301

5. Plug the power cable into the main power supply outlet
and turn the ADU-301 on.
The power LED turns green.
6. The LED indicator located on the front panel of the
CRLU-201:
a. Flashes to indicate that power has been turned on.
b. Turns off to indicate that the CRLU-201 is loading
its programming.
c. Turns on to indicate the CRLU-201 is operational.
7. Plug the microphone jack into the MIC INPUT: MIC
connector on the ADU-301. If you are using an external
PTT, plug the jack into the MIC INPUT: PTT
connector.
8. Connect your audio source (i.e., compact disk player,
radio, etc.) to the Channel A or Channel B connectors
on the rear panel of the ADU-301. If your audio source
is in stereo, use the CAB-MINI-COMB-3 or CAB-PL-
COMB-3 cable.
9. If you intend to transmit prerecorded audio messages,
use either a commercial 1/8-1/4 inch stereo cable or the

WAVES Installation and Operation Manual 7-5

Installing the WAVES Hardware

CAB-ADU-SB-3 cable to connect your PC sound card

line output to the PC SOUND CARD: FROM
connector on the ADU-301.
10. Double-click the WAVES icon to start the WAVES
software and then open a WAVES file.

11. Turn on your audio source.

7.4 INSTALLING THE TRANSCEIVERS

7.4.1 INTIALIZING THE TRANSCEIVERS

All transceivers (CRLU-201 and TRX-401) are identical when
they leave the factory. You must give each transceiver a unique
identity by configuring (or initializing) its parameters. These
parameters are then stored in the transceiver’s EEPROM
(nonvolatile memory).

³ To initialize a transceiver’s parameters:

1. Loosen the screws on both sides of the plastic case and
slide the bottom cover off.

Figure 7-4 Back Panel of the TRX-401

2. Plug the power cable into the main power supply outlet
to turn the transceiver on.

7-6 WAVES Installation and Operation Manual

 Installing the Transceivers

The LED indicator located on the transceiver’s front

panel:
a. Flashes to indicate that power has been turned on.
b. Turns off to indicate that the transceiver is loading
its programming.
c. Flashes or turns on continuously to indicate the
transceiver is operational.
3. Double-click the WAVES icon, open a WAVES file and
click Wired on the Mode menu.
4. Connect one end of the CAB-PC-ADU-3 cable to the
serial port of your PC and the other end to the RS-232
port of the transceiver to be initialized.
5. On the site tree, click the unit to be initialized and then
open the Properties dialog box, select the Unit ID tab
and click Update the Unit.
WAVES sends the Unit ID to the transceiver.
6. On the Commands menu, click DB to Unit or use the
Properties dialog box to update each category
separately.
WAVES downloads the initialization parameters.
7. To check that the transceiver has been initialized
correctly, do one of the following:
x On the Commands menu, click Peep Unit Info.
The Monitor dialog box opens. The Monitor dialog
box shows the internal parameter settings of the unit.
x On the Commands menu, click Verify.
The Verifying Unit Settings dialog box opens. In
the Verifying Unit Settings dialog box, WAVES
compares the transceiver’s parameters with those
listed for the transceiver in the WAVES file and
advises which ones match and which, if any, do not.
8. Remove the CAB-PC-ADU-3 cable from the RS-232
port of the transceiver.
9. Tighten the screws on both sides of the bottom cover to
secure it to the plastic case.

WAVES Installation and Operation Manual 7-7

Installing the WAVES Hardware

10. Repeat Steps 1-9 until all the transceivers are

initialized.
11. It is recommended to write the ID number on a sticker
and attach it to every unit for later identification during
the installation.

7.4.2 MOUNTING THE TRANSCEIVERS

After the transceivers (CRLU-201 and TRX-401) are initialized,
they are ready to be mounted. You can mount a transceiver on a
wall or a pole. Each transceiver comes with a back plate that
makes mounting the unit easy.

In general, mount the transceivers right-side up. If you are

mounting a transceiver 10 m or more above the transceiver from
which it receives RF signals, mount the transceiver upside
down.

³ To mount a transceiver:
1. Move the locking plate to enable sliding of the
transceiver.
2. Detach the transceiver from the back plate by sliding it
and pulling out.
3. Attach the back plate to a wall or pole using standard
screws, metal pipe fasteners or metal tie-cables (see
Figure 7-6). Make sure that the screws, fasteners or tie-
cables can support a load of at least 30 lb. (14 kg).

7-8 WAVES Installation and Operation Manual

 Installing the Transceivers

Note: If you are mounting one or more UPS-901

backup batteries onto the same back plate,
make sure that the screws, fasteners or tie
cables can support an additional load of 11 lb.
(5 kg) per backup battery.
B ack P late
Locking P late

Figure 7-5 Mounting the CRLU on the Back Plate

Wall M ounting Pole Mounting

Figure 7-6 Mounting the Back Plate on a Wall or Pole

4. Attach the transceiver onto the mounted back plate by

inserting its pins to the back plate holes and sliding it
down.

5. Move the locking plate to lock the transceiver.

WAVES Installation and Operation Manual 7-9

Installing the WAVES Hardware

7.4.3 CONNECTING PERIPHERALS TO A TRANSCEIVER

You can connect speakers, visual displays and other data
devices to a transceiver (CRLU-201 and TRX-401).
AD U-301 _ REAR PA NEL
C H A NN E L A L INE IN P U T CH A N N E L B L IN E IN P UT P C S O U ND C A RD D ATA P O RT S SYNC IC M

P E A K C LIP P E A K C LI P IN O UT
PAD PA D R S -2 3 2 to C RL U R S -2 32

TR IM T RIM FR OM TO to C R LU to P C C o ntro l

A C Line In

Analog and/or digital I/O devices

Am plifier
D evice that uses D C pow er
Alternate base station sw itch

ADU R S-232
J1
11 10 9 8 7 6 5 4 3 2 1
AM P O U T +15V I/O LINE O UT
J4
J2
J6
+1 2VDC

Sp eake rs
J5

A C L in e In

Figure 7-7 CRLU-201 Wiring Diagram

A m plifie r
A nalog or digital I/O d evice s CA B-R S23 2-DC E-3
or
Device th at use s DC power
CAB -R S232 -DTE -3 R S-232
DC E or DTE
Data D evice

RS -232
J1
11 10 9 8 7 6 5 4 3 2 1
A MP O U T +15V I/O LINE OUT
J4
J2
J6
+12 VD C

S p e a k e rs
J5

A C Line In

Figure 7-8 TRX-401 Wiring Diagram

7-10 WAVES Installation and Operation Manual

 Installing the Transceivers

³ To connect peripherals:

CONNECT THE SPEAKERS TO J1

1. Loosen the screws on both sides of the plastic case and
slide the bottom cover off (see Figure 7-2 and
Figure 7-4).
2. Remove the J1 male connector by loosening the screws
and pulling the connector out.
The J1 connector is a 5-pin Phoenix connector used to
drive the speakers. Figure 7-9 shows the configuration
of the connector.

Ch. 2 neg (-) Ch. 2 pos (+) ground Ch. 1 pos (+) Ch. 1 neg (-)
5 4 3 2 1

Figure 7-9 Configuration of the J1 Connector

3. Attach the speaker cables to the J1 connector and

reinsert the connector into its slot on the bottom panel.

CONNECT THE EXTERNAL AMPLIFIER AND I/O

DEVICES TO J2
4. To attach an external amplifier, an external sensor or an
external device that uses DC voltage to the J2
connector, obtain an appropriate 11-pin male connector.
5. To attach an external amplifier, connect the amplifier’s
cable to pins 1-5 of the 11-pin male connector (see
Figure 7-10).

Line neg (-) Line pos (+) ground Line pos (-) Line neg (-)
5 4 3 2 1

Figure 7-10 Configuration of Pins 1-5 on the J2 Connector

6. To attach an external analog input device (0-10V),

connect the analog device’s cable to pin 3 and 6 of the
11-pin male connector (see Figure 7-11).

WAVES Installation and Operation Manual 7-11

 Installing the WAVES Hardware

7. To attach an external digital input device (0-5V),

connect the digital device’s cable to pin 3 and 10 of the
11-pin male connector (see Figure 7-11).
8. To attach an external digital I/O device (0-5V), connect
the digital device’s cable to pin 3 and to pin 8 or 9 of
the 11-pin male connector (see Figure 7-11).
9. To attach an external device that uses DC voltage,
connect the device’s cable to pin 3 and pin 11 of the 11-
pin male connector (see Figure 7-11).
Note: It is recommended to attach only devices that
consume less 0.5 AMP.

+15V Digital Input 1 Digital I/O2 Digital I/O3 Reserved Analog Input
11 10 9 8 7 6

Figure 7-11 Configuration of Pins 6-11 on the J2

Connector
10. Insert the 11-pin male connector into the J2 female
connector on the bottom panel.
11. To attach a visual display sign or any other device with
an RS-232 connector, connect the device’s cable to the
RS-232 connector on the bottom panel.
12. Connect the transceiver to a power source to turn it on.
13. Tighten the screws on both sides of the bottom cover to
secure it to the plastic case.

7-12 WAVES Installation and Operation Manual

 Installing the Transceivers

7.4.4 INSTALLING ALTERNATE BASE STATION SWITCH

When configuring a unit as SRLU it can also serves as an
alternate base station using a switch that shorts pin 10 of J2 to
pin 3 of J2. See more details in “Chapter 9 –Advanced
Features”.

The following diagram shows the connection to J2 of the

SRLU.
to J2

10

Altern ate
N orm a l Base -Sta tion
3

A lte rn a te B a se
S ta tio n S w itch

Figure 7-12 Alternate Base Station Connection

Note: It is recommended to attach a sticker for each mode

(Normal mode and Alternate Base Station mode) on the
switching box.

7.4.5 INSTALLING A BACKUP BATTERY

An optional UPS rechargeable backup battery (UPS-901) is
available for installation with the CRLU-201 and the TRX-401.
This backup battery can provide up to six hours of operation.
You can also stack UPS-901 units to extend backup time.

Vin
Vin+15V
V bat+12 V

C HRG.

Figure 7-13 UPS-901 Bottom Panel

WAVES Installation and Operation Manual 7-13

Installing the WAVES Hardware

³ To install the UPS-901:

1. Disassemble the transceiver from its mounting plate.
2. Disassemble all four mounting pins including the
square nuts (items 1 and 2) from the CRLU-201 or
TRX-401 units (see Figure 7-14, step A).
3. Remove the two gauges (item 3)from the CRLU-201 or
TRX-401 units.
4. Disassemble the two sockets set screws and their square
nuts (items 2 and 4) from the UPS unit (see Figure 7-
14, step B).
5. Assemble the two sockets set screws and their square
nuts (items 2 and 4) to the CRLU-201 or TRX-401
units (see Figure 7-14, step C).
6. Assemble the two mounting pins with the square nuts
(items 1 and 2) to the edge of the UPS unit (see Figure
7-14, step D).
7. Insert the two gauges (item 3) to maintain exact
distance between the mounting pins, and then insert the
other two mounting pins with the square nuts to the
other edge of the UPS unit.
8. Connect the CAB-UPS cable to the UPS connector on
the bottom panel of the UPS-901, and to the J6
connector on the bottom panel of the CRLU-201 or
TRX-401 (see Figure 7-15).
9. Connect the power cable of the CRLU/TRX to the AC
outlet. The UPS-901 red and green indicator lights turn
on (see Figure 7-13). The green indicator light (Vin)
indicates that the UPS-901 is receiving DC power from
the CRLU-201 or TRX-401 and the red indicator light
(CHRG) indicates that the battery is recharging.
Note: a) Use the CAB-UPS-D cable to install two
UPS-901 backup batteries in parallel.
b) If you are installing one or more UPS-901
backup batteries on the same back plate,
make sure that the screws, fasteners or tie
cables (used to mount the back plate onto a
wall or pole) can support a load of 11 lb. (5
kg) per backup battery, in addition to the
minimum load of 30 lb. (14 kg).

7-14 WAVES Installation and Operation Manual

 Installing the Transceivers

1
TRX/CRLU U PS

2 1 2 4

2 1

S te p A S tep B

2 4 2 1

2 1

S te p C S tep D

Figure 7-14 UPS Mounting on TRX/CRLU

Figure 7-15 UPS Mounted on TRX/CRLU

WAVES Installation and Operation Manual 7-15

Installing the WAVES Hardware

³ To replace batteries in the UPS-901:

1. After removing the UPS-901 from the transceiver unit,
unscrew the five screws of the bottom plate and remove
the two batteries, including the charger card from its
case (see the following diagram).

B atte ry

C ha rg e r C a rd

B a tte ry

Figure 7-16 UPS-901 – Inside View

2. Disconnect the cables from the batteries and replace the
two batteries with new ones.
3. Reconnect the cables to the new batteries and make sure
that correct polarity.
4. Reinsert the batteries including the charger card to its
case carefully, and close the five screws.

Caution: During insertion of the batteries with the charger

card to its case, pay attention not to damage the
components of the charger card.

7.4.6 INSTALLING SOLAR PANNELS WITH BACKUP BATTERY

Optional solar panels are available for installation with a
rechargeable backup battery. These solar panels can provide
recharging current to the backup battery in order to enable the
WAVES system to keep working even if the network power
supply is down for a long time (see Figure 7-17).

The solar panels are connected to a charging controller. When

the battery is fully charged, the controller stops the current flow

7-16 WAVES Installation and Operation Manual

 Installing the Transceivers

to the battery, and when the battery voltage falls to 10.5 V, the
controller renews the current flow to the battery.

1
S olar P anel 1

2
S olar P anel 2

S olar P ane ls - Side View

R ear View
C harg ing C on troller

C A B -S O L A R C O N T
U N IT -3

+ - C R LU -201
B attery or
TR X -401

Figure 7-17 Two Solar Panels Wiring Diagram

The following solar panels are examples of commercial solar

panels:
x SOLAREX MSX-60 with 3.5 A charging current (or
equivalent).
x SOLAREX MSX-64 with 3.66 A charging current (or
equivalent).
x SOLAREX MSX-77 with 4.56 A charging current (or
equivalent).
x SOLAREX MSX-83 with 4.85 A charging current (or
equivalent).

When selecting a solar panel, consider the following

parameters:
x E - Energy consumption per day [Ah/day]
x S - Weather conditions (hours of sunlight per day [h/day]).
x Dust and sun absorption factor (usually 1.3)
Calculate the charging current C as follows:
C = E * 1.3 / S

WAVES Installation and Operation Manual 7-17

Installing the WAVES Hardware

For example:
E = 22.5 Ah/day
(23 hours of idle mode - 16.1 Ah + 1 hour of announcements –
4 Ah + 24 hours of intercom operation – 2.4 Ah)
S = 4 h/day (in Tel-Aviv from December to February)
C = 22.5 * 1.3 / 4 = 7.3 A

Conclusion: Two SOLAREX MSX-64 modules (or

equivalent) connected in parallel are suitable for
these conditions.

When selecting the backup battery size, consider the number of

“autonomic days” (days with no sun radiation) required for
operation with backup batteries only.

For example: for normal operation (consumption of 22.5 Ah per

day) in four “autonomic days” you need a battery with capacity
of 90 Ah (use always a 12 V battery).

Notes: a) Solar panels mountings are available from

MADAH-Com. Consult MADAH-Com to determine
the panel angle that is depending on the
installation latitude.
b) Consult MADAH-Com for selecting the charging
controller type.

7-18 WAVES Installation and Operation Manual

 Installing the Transceivers

7.4.7 INSTALLING EXTERNAL ANTENNAS

Each transceiver has two built-in diversity antennas: one for
receiving and the other for receiving and transmitting.

Depending on your site requirements, you may want to replace

one or both of the built-in antennas with an external antenna
supported by the WAVES transceivers:
x ANT-103 - 3dBi Omni directional whip antenna
x ANT-109 - 9dBi directional 70º beam planar antenna
x ANT-109/OM - 9dBi omni-directional whip antenna
x ANT-114 - 14dBi directional 25º beam YAGI antenna
x ANT-114/DR - 14dBi directional 25º beam plannar antenna

The following table presents the typical operating ranges of the

above antennas under specific environmental conditions:

Antenna Outdoor Outdoor Indoor Indoor

LOS1 Non-LOS1 Lightly Built Heavily Built
Built-in 1,200 ft. 300 ft. 200 ft. 100 ft.
diversity (360 m) (90 m) (60 m) (30 m)
ANT-103 2,000 ft. 500 ft. 300 ft. 150 ft.
(600 m) (150 m) (90 m) (45 m)
ANT-109 5,000 ft. 1,000 ft. 500 ft. 250 ft.
(1,500 m) (300 m) (150 m) (75 m)
ANT-109/OM 5,000 ft. 1,000 ft. 500 ft. 250 ft.
(1,500 m) (300 m) (150 m) (75 m)
ANT-114 10,000 ft. 1,500 ft. 1,000 ft. 500 ft.
(3,000 m) (450 m) (300 m) (150 m)
ANT-114/DR 10,000 ft. 1,500 ft. 1,000 ft. 500 ft.
(3,000 m) (450 m) (300 m) (150 m)
1
LOS stands for Line of Sight

WAVES Installation and Operation Manual 7-19

Installing the WAVES Hardware

ANT-103 ANT-109 ANT-109/OM

P C 2 415N

cu sh cr aft

ANT-114

ANT-114/D R

Figure 7-18 External Antennas Supported by WAVES

7-20 WAVES Installation and Operation Manual

 Installing the Transceivers

Connecting an external antenna to a transceiver automatically

deactivates that transceiver’s built-in antenna.

WARNING: According to FCC regulations, only a MADAH-

Com authorized installer may install an external
antenna on a WAVES transceiver.

³ To connect an external antenna to a transceiver:

1. Pull out the clip screw fasteners on both sides of the top
cover by inserting a screwdriver between the clip and
the cover and then sliding the cover off.

Figure 7-19 Removing the Top Cover of a Transceiver

WAVES Installation and Operation Manual 7-21

Installing the WAVES Hardware

2. Mount the SMA connectors onto the antenna board by

inserting them into their slots and tightening the screws.
Be careful to mount the connectors facing the back
panel of the transceiver.
NO SOLDERING IS REQUIRED.

S prin g W ashe r
a nd H ex N u t

SM A M AC O M
C onnector C onnector

Figure 7-20 Antenna Board

3. Connect the antenna cable to the left SMA connector to

replace the receive only antenna or to the right SMA
connector to replace the receive and transmit antenna.

An te nn a ca ble
fo r th e rece ive
o nly an ten n a

An te nn a ca ble
fo r th e rece ive
a nd tra nsm it an te nn a

Figure 7-21 Connecting an Antenna Cable to the Antenna Board

7-22 WAVES Installation and Operation Manual

 Installing the Transceivers

4. Cut a hole on one of the top cover’s side panels to the

make room for the antenna cable.

U se th e ho le s he re
fo r th e a nten na cab le s

Figure 7-22 Cutting a Hole in the Top Cover’s Side

Panel

5. Replace the top cover and push the clip fasteners back
into place to secure the cover to the plastic case.

³ To mount the antenna on a wall or pole:

x Follow the instructions included in the antenna
installation kit.

WAVES Installation and Operation Manual 7-23

Installing the WAVES Hardware

7.5 INSTALLING THE EMP-111 EMERGENCY

PUSH BUTTON
Pressing the EMP-111 sends an emergency signal to the base
station, where the warning is logged in the System’s Condition
Report dialog box. When configured, it activates a WACOL
command to make an emergency announcement or turn on an
external device.

Before connecting the EMP-111 to a field transceiver, you

should activate the field transceiver’s digital input pin and
assign to it emergency priority and a WACOL command in the
I/O Settings tab of the Properties dialog box (see Chapter 6).

³ To install the EMP-111:

1. Loosen the screws on both sides of the TRX-401’s
plastic case and slide the bottom cover off.
2. Insert the 11-pin male connector (at the end of the
EMP-111 cable) into the J2 female connector on the
bottom panel of the transceiver.
3. Replace the bottom cover of the TRX-401 and tighten
the screws on both sides to secure it to the plastic case.

B row n /B lack

to J2

B lue/R ed
Figure 7-23 EMP-111 Cable – Wiring Diagram

³ To operate the EMP-111:

x Press the red button on the top panel of the EMP-111.

7-24 WAVES Installation and Operation Manual

 Installing EMP-211 Wireless Remote Activator

7.6 INSTALLING EMP-211 WIRELESS REMOTE

ACTIVATOR
The EMP-211 operates as a wireless emergency push button. It
is a remote control device (EMP-211-WTX) that enables you to
send a wireless emergency signal through the EMP-211-WRX
to the WAVES base station, where the warning notifies the
operator according to the monitor report filter table.

If configured, it also activates a WACOL command to make an

emergency announcement, or turns on an external device (see
Figure 7-24).

E M P -211 -W R X

to J2
11
+ 15 V

6
sig na l
W ire le ss
E M P -211-W T X
GND
3 R e m o te
A ctiv ato r

Figure 7-24 EMP-211-WRX and EMP-211-WTX General View

Before connecting the EMP-211-WRX to a TRX-401, you

should activate the TRX-401’s analog input pin and assign to it
an emergency priority and a WACOL command in the I/O
Settings tab of the Properties dialog box (see Chapter 6).

Before mounting the EMP-211-WRX, do the following:

WAVES Installation and Operation Manual 7-25

Installing the WAVES Hardware

x Program and calibrate the EMP-211-WRX.

x Calibrate the input circuit in the TRX connected to the
EMP-211-WRX.
x In WAVES application, configure the analog I/O parameters
to receive the all pre-defined emergency transmitters.
x Check the operation of the system with all transmitters.

You can mount the EMP-211-WRX on a wall or a pole. Each

EMP-211-WRX has a base with holes to make the mounting of
the unit easy.

In general, mount the EMP-211-WRX with the antennas in a

vertical position.

³ To program and calibrate the EMP-211-WRX:

1. Connect +15 Vdc to pin 11 and ground to pin 3 of the
EMP-211-WRX cable.
2. Connect a voltage meter to pin 6 of the EMP-211-WRX
cable (signal output).
3. Remove the cover of the EMP-211-WRX.
4. Adjust the signal output to 6.5 Vdc using the trimmer
on the receiver card located inside the EMP-211-WRX.
5. Program the EMP-211-WRX to receive up to 12
different transmitters (EMP-211-WTX) according to
their ID’s (with difference of 0.5 V between the
transmitters). See section 3 – Programming in
Appendix H).
It is recommended to write the ID’s on stickers and
attach them to each one of the transmitters.

³ Calibrate the input circuit in the TRX-401:

1. Connect the EMP-211-WRX cable to the TRX-401.
6. Using WAVES application, check the voltage of the
analog input using the monitor window (select the
TRX-401 unit from the tree, and then from commands
menu select Monitor). When no transmitter is
activated, the value should be 166, readjust if necessary,
using the trimmer on the receiver card located inside the
EMP-211-WRX.

7-26 WAVES Installation and Operation Manual

 Installing EMP-211 Wireless Remote Activator

Note: Repeat this procedure for each installation of TRX-401

with EMP-211-WRX.

³ To configure the analog I/O parameters:

x See section “7.4.3 Configuring the Analog Report
Parameters”, and set the parameters as follows:
 Set the range to 0 – 255.
 Define the normal range as 164 – 255 (the
command will be activated when the analog input
voltage drops below 6.5 V (one of the transmitters
is activated).
 Set the command “reportanalog”.
 Define the ranges for each one of the transmitters
and name it.
 Set to emergency priority.

³ To mount the EMP-211-WRX:

x Attach the base to a wall or pole using standard screws,
metal pipe fasteners or metal tie-cables.
(See Appendix H – EMP-211-WRX Installation and
Operation manual).

³ To connect the EMP-211-WRX to a TRX-401:

1. Loosen the screws on both sides of the TRX-401’s
plastic case and slide the bottom cover off.
2. Disconnect J2 connector from the TRX-401.
3. Connect the three wires of the EMP-211-WRX cable to
J2 according to their numbers.
4. Reconnect J2 connector to the TRX-401.
5. Replace the bottom cover of the TRX-401 and tighten
the screws on both sides to secure it to the plastic case.

³ To operate the EMP-211-WRX:

1. Point the EMP-211-WTX at a corresponding EMP-211-
WRX. Make sure you are standing within a 50-200 m
radius of the EMP-211-WRX.
2. Press the top button.

WAVES Installation and Operation Manual 7-27

Installing the WAVES Hardware

The WAVES system responds according to the

pre-defined program.

7.7 INSTALLING LED SIGN

You can connect the RS-232 interface of the LED sign directly
to J2 connector of the TRX-401, or to RS-232 J1 connector of
the ICM-501 (see Figure 11-3).

When connecting the LED sign to the ICM-501, define the LED
sign connection to enable multiplexing on the RS-232
communication link.

R S -2 3 2
J1
11 10 9 8 7 6 5 4 3 2 1
AM P OUT + 15V I/O LIN E O U T
J4
J2
J6
+ 12VD C

LED Sign
J5

TRX-401

Figure 7-25 LED Sign Connection to TRX-401

7-28 WAVES Installation and Operation Manual

 Installing Strobe Light

7.8 INSTALLING STROBE LIGHT

You can connect a Strobe Light to enable visual alarm. Connect
the Strobe Light cable to J2 connector of the TRX-401, as
shown in the following figure.

J2
11
+ 15 V
sign al 9

3
S tro b e Ligh t
GND

Figure 7-26 Strobe Light Connection to TRX-401 (J2)

After connecting the Strobe Light, set the I/O parameters in

WAVES application as follows:
1. Set I/O2 to Output.
2. Type the WACOL commands as follows:
iooutput addr(1,0,3) = 1 , port=2.

WAVES Installation and Operation Manual 7-29

CHAPTER 8

OPERATING WAVES

This chapter includes the following sections:

x Adjusting the volume
x Live voice messages
x Sending visual display messages
x Working with pre-recorded messages

WAVES Installation and Operation Manual 8-1

Operating WAVES

8.1 ADJUSTING THE VOLUME

You can quickly adjust the volume and mute settings for audio
and voice using the Volume/Mute Control window
(see Chapter 6).

In an emergency, you can easily override all mute settings

(including Mute Lock) on the voice channels and raise the
volume of the voice channels according to the emergency gain
(see Chapter 6).

Note: WAVES graphically indicates the emergency mute state

by placing the emergency indicator below the colored
sliders on the site, zone, sub-zone and unit levels in the
Volume/Mute Control window.

³ To override all mute settings on the voice channels

and raise the volume of the voice channels
according to the Emergency Gain:
x On the Command menu, click Emergency.

³ To restore the original volume and mute settings of

the voice channels:
x On the Command menu, click Emergency.

Note: Only the mute settings on the unit level are restored.
Mute settings on the site, zone and sub-zone levels
are cancelled.

8-2 WAVES Installation and Operation Manual

 Live Voice Messages

8.2 LIVE VOICE MESSAGES

You can transmit real-time voice messages using a microphone
connected to the ADU.

8.2.1 USING A PTT MICROPHONE

³ To transmit a message to all transceivers:
1. Plug the microphone jack into the MIC INPUT: MIC
connector on the front panel of the ADU.
2. Press the PTT switch, hold and talk.

8.2.2 USING A PC-CONTROLLED PTT

When you press a key to activate the microphone, the
“Microphone is on” message appears on the upper left corner of
the main screen work area and remains there until you release
the key you pressed.

³ To transmit a voice message to all transceivers:

1. Plug the microphone jack into the MIC INPUT: MIC
connector on the front panel of the ADU.
2. Click anywhere on the site tree.
3. Press the spacebar, hold and talk.

³ To transmit a voice message to a specific area:

1. Plug the microphone jack into the MIC INPUT: MIC
connector on the front panel of the ADU.
2. Click a zone, sub-zone or unit on the site tree.
3. Press ENTER, hold and talk.

³ To transmit a voice message to the first ten zones:

1. Plug the microphone jack into the MIC INPUT: MIC
connector on the ADU’s front panel.
2. Press the numbered key that corresponds to the number
of the zone to which you want to transmit a message,
hold and talk.

WAVES Installation and Operation Manual 8-3

Operating WAVES

8.3 SENDING VISUAL DISPLAY MESSAGES

If your transceivers are equipped with visual displays, you can
quickly type a message and send it to a selected area. The
message is displayed in the default format and with default
effects.

³ To transmit a visual display message:

1. Select the site or a site element on the site tree.
2. On the Commands menu, click Send Text.

The Send Text dialog box opens.

3. Type a message in the top text box.

- or -
Click one of the previously sent messages listed below
the text box.
4. Click Send or press ENTER.

8-4 WAVES Installation and Operation Manual

 Working with Pre-Recorded Messages

8.4 WORKING WITH PRE-RECORDED

MESSAGES
You can pre-record a voice message and/or prepare a text
message with special effects and transmit them when they are
needed.

Following are general guidelines to help you handle pre-

recorded messages:
1. Prepare an audio file in digital format with the .wav
extension and place it in the WAVES folder.
2. Prepare the text for a visual display message.
3. Merge the audio and visual display messages into one
message in the Audio Visual dialog box.
4. Transmit the message to selected areas when needed.

If your transceivers are equipped with both audio and visual

equipment, you can transmit messages simultaneously to
loudspeakers and visual displays.

8.4.1 PREPARING AN AUDIO MESSAGE

³ To prepare an audio message:
1. Connect one end of a commercial 1/8-1/4 inch stereo
cable or the CAB-ADU-SB-3 cable to the PC SOUND
CARD: TO connector on the rear panel of the
ADU-301 and the other end to your PC’s sound card
line input.
2. Start your PC recording application and adjust the
recording level using the microphone plugged into the
MIC Input IN connector on the ADU’s front panel.
3. Record an audio message (preferably with CD quality)
and save it with the .wav extension.

WAVES Installation and Operation Manual 8-5

Operating WAVES

8.4.2 PREPARING A VISUAL DISPLAY MESSAGE

³ To prepare a visual display message:
1. On the View menu, click AVM Window.
The Audio Visual dialog box opens.

2. Click New.
“No Name” appears in the Name column.
3. Click “No Name” and type a descriptive name.
4. Click the new message name and do one of the
following:
a. Click the Plain Text box and type the message.
b. Click OK.
WAVES translates the text into all the protocols
saved in the WAVES database without special
effects.
- or -
a. Click Displays.
The Remote Display Drivers dialog box opens.
b. Click a protocol and then click Use.

8-6 WAVES Installation and Operation Manual

 Working with Pre-Recorded Messages

The Remote Display Drivers dialog box closes

and the protocol name appears in the Display Signs
box.
c. Click a protocol in the Display Signs box and then
click Edit.
d. In the Editor dialog box, type a message, modify
the protocol settings, and click OK.
WAVES translates the text into the protocol listed in
the Display Signs box.

Note: You can list more than one protocol in the

Display Signs box and modify the protocol
settings by repeating Steps a-d.

For information on modifying the ComFuture

driver’s protocol settings, see Appendix F.

³ To install a driver:
1. On the View menu, click AVM Window.
2. In the Audio Visual dialog box, click Displays.
The Remote Display Drivers dialog box opens.
3. Click Install New Driver.
The Open dialog box appears.
4. Type or locate a filename and click Open.
The Open dialog box closes and the selected driver’s
name appears in the list of drivers on the Remote
Display Drivers dialog box.
5. Click Close.
The Remote Display Drivers dialog box closes.

WAVES Installation and Operation Manual 8-7

Operating WAVES

8.4.3 ATTACHING A PRE-RECORDED AUDIO MESSAGE

³ To attach an audio file to a pre-recorded text
message for simultaneous transmission:
1. On the View menu, click AVM Window.
2. In the Audio Visual dialog box, click a text message
name.
3. Type a filename in the Audio box or locate the file by
clicking the magnifying glass.
4. Click OK.

8.4.4 SENDING PRE-RECORDED AUDIO VISUAL MESSAGES

(AVM)
³ To transmit a pre-recorded audio-visual message:
1. Click the site, a zone, a sub-zone or a unit on the site tree.
2. On the View menu, click AVM Window.
3. In the Audio Visual dialog box, click a message name.
4. Click Send.

³ To hear the message before transmission:

1. Connect a speaker or earphone to the MONITOR: OUT
connector on the ADU.
2. Under Audio on the Audio Visual dialog box, click
Play.

8-8 WAVES Installation and Operation Manual

CHAPTER 9

ADVANCED FEATURES

This chapter includes the following sections:

x WACOL command language
x The WACOL shell
x The scheduler
x Alternate base station

WAVES Installation and Operation Manual 9-1

Advanced Features

9.1 WACOL COMMAND LANGUAGE

You can execute WAVES procedures using WAVES Command
Language (WACOL) statements.

You can use WACOL statements in the:

x WACOL Shell
x Scheduler
x I/O Settings tab of the Properties dialog box (see Chapter 6)
x Emergency
x Report filter (“playwav” command)

9.1.1 WORKING WITH WACOL STATEMENTS

You can write a WACOL statement to execute a simple WAVES
procedure or a series of WACOL statements to execute a
complex set of WAVES procedures.

Note: If you write a series of WACOL statements, make sure

to use semicolons to separate the statements.

WACOL statements are written using the following format:

command addr(a,b,c) = list of parameters

Where
a = zone address number
b = sub-zone address number
c = unit address number

Note: Optional parameters are written in italics.

If the statement includes more than one parameter,
commas separate the parameters.
To send a message to all units, type addr(0,0,0).

9-2 WAVES Installation and Operation Manual

 WACOL Command Language

Following are the most commonly used WACOL commands:

EmergencyOn

Function
This command enables the Emergency feature.

Format
emergencyon

EmergencyOff

Function
This command disables the Emergency feature.

Format
emergencyoff

IoOutput

Function
This command turns a transceiver’s port on or off.

Format
iooutput addr(a,b,c) = P1, port = P2

Format Explanation
P1: Value to send. The value can only be 0 or 1, where
0 = off (0V) and 1 = on (5V)
P2: Port number. The port number can only be 2 (for
Digital I/O 2) or 3 (for Digital I/O 3).

Example:
To turn on the second port of the unit located at 5.3.7,
type:
iooutput addr(5,3,7) = 1, port = 2

Note: You can send this command to only one unit at a

time and not to a group of units.

WAVES Installation and Operation Manual 9-3

Advanced Features

PttOn

Function
This command activates the PTT microphone to enable
you to transmit a voice message to the site or a specific
site element.

Note: Activating this command from the WACOL shell

freezes WAVES in PTT mode.

Format
ptton addr (a,b,c)

PttOff

Function
This command deactivates the PTT microphone.

Format
pttoff

Report

Function
This command is used to send a message to the System’s
Condition Report dialog box and the log file and to open
the Condition Report dialog box.

Format
report = P1, error = P2, categ = P3, open = P4, desc =
P5

Format Explanation
P1: Message name
P2: Problem type, where:
Error = 1
Warning = 0
P3: Category type, where
Critical = 0
WACOL = 1
Com Port = 2
GUI = 3
GDI = 4

9-4 WAVES Installation and Operation Manual

 WACOL Command Language

File System =5
Queue Full = 6
I/O = 7
BIT = 8
Other = 9
P4 Opening the System’s Condition Report dialog box,
where:
Do not open = 0
Open = 1
P5 Detailed description of the problem

Note: P3 is relevant only when P2 = 0.

Example:
To send a message to the System’s Condition Report
dialog box and to the log file advising that a warning has
occurred, and to open the System’s Condition Report
dialog box, type:

report = “Error Warning”, error = 0, categ = 9, open = 1,

descr = “An error has occurred.”

SendAvm

Function
This command is used to send an AVM message.

Format
sendavm addr(a,b,c) = P1

Format Explanation
P1: Number of the AVM message

Example:
To send AVM message no. 12 to the unit located at 5.3.7,
type:
sendavm addr(5,3,7) = 12

WAVES Installation and Operation Manual 9-5

Advanced Features

SetAudio

Function
This command is used to set a unit’s audio parameters.

Format
setaudio addr(a,b,c) = P1, param = P2, channel = P3

Format Explanation
P1: Value to set for volume, treble bass or mute
Note: When setting mute, 1 = mute and 0 =
unmute
P2: Parameter type, where:
Volume = 0
Mute = 1
Bass = 2
Treble = 3
P3 Output channel (1-4)

Examples:
1. To set the volume of Channel 1 to 20 for the unit
selected on the site tree, type:
setaudio = 20, param = 0, channel = 1
2. To set the treble of Channel 2 to 10 for the unit
located at 1.0.1, type:
setaudio addr(1,0,1) = 10, param = 3, channel = 2
3. To mute the first voice channel of all units, type:
setaudio addr(0,0,0) = 1, param = 1, channel = 3

SetMode

Function
This command is used to set the operating mode.

Format
setmode = P1

Format Explanation
P1: Operating mode type, where:
Off-line = 0

9-6 WAVES Installation and Operation Manual

 WACOL Command Language

Wired = 1
On-line = 2
User = 3

Example:
To set the operating mode to Wired, type:
setmode = 1

UpdateAll

Function
This command is used to update all unit parameters.

Format
Updateall

PauseSched

Function
This command pauses or un-pauses the scheduler.

Format
PauseSched = P1, index=P2

Format Explanation
P1: pause = 0
un-pause = 1
P2: scheduler index

Example:
To un-pause event 11 in the scheduler, type:
PauseSched = 0, index=11

Playwav

Function
This command activates a *.WAV file when buzzer
activation is required.

Format
Playwav = “File name.WAV”

WAVES Installation and Operation Manual 9-7

Advanced Features

Reportanalog

Function
This command reports according the analog division.
When a value falls below the correct value range for the
analog pin, WAVES performs this WACOL command
and also sends a message (including the analog division
name, unit name and unit address) to the system
condition’s report window.

Format
Reportanalog

9.1.2 CUSTOM COMMANDS

MADAH-Com enables using of custom commands that are not
presented in the WAVES graphic user interface (not as menus or
icons).

In versions 4.3 and 4.5, the custom command AGC control is

supported.

Agc control

Function
This command controls the attenuation of receiver input
circuit.

Format
Customcmd=172,msgbody=P1 a5 05 50 5a, length=5

Format Explanation
P1: Automatic AGC = 00
AGC on = f0
AGC off =0f

Example:
To activate the AGC, type:
Customcmd=172,msgbody= f0 a5 05 50 5a, length=5

9-8 WAVES Installation and Operation Manual

 The WACOL Shell

9.2 THE WACOL SHELL

You can execute all WAVES procedures from the WACOL shell
using WAVES Command Language (WACOL) statements.

In general, you should use the WAVES dialog boxes to perform

these operations. However, if you have to perform a long
procedure or a procedure used at different times, you can save
time and effort by writing it in the WACOL shell and saving the
command statement.

Note: For a description of the WACOL syntax and a list of

WACOL statements, see 9.1.1.

³ To execute a WAVES procedure using a WACOL

statement:
1. On the View menu, click WACOL Shell.
The WACOL Shell dialog box opens.

2. In the Command Line box, type a new WACOL

statement.
Or
Click the Command Line arrow and then click a
WACOL statement.

Note: If you modify a saved WACOL statement,

WAVES saves the statement in its old and new
forms.

WAVES Installation and Operation Manual 9-9

Advanced Features

3. Click Go.
WAVES executes the WACOL statement. The WACOL
statement appears in the Command box and is added to
the command list.
4. Click Close to close the WACOL Shell dialog box.

³ To save a WACOL command line

1. After executing a WACOL command, click the Save
button. Save as dialog appears.
2. Type the file name (with .txt extension) and click the
Save button.

³ To restore a saved WACOL command

1. Open the saved WACOL command with a notepad
application (or any other windows based ASCII editor).
2. In WAVES application, from the View menu, select the
WACOL shell.
3. In notepad application, copy the WACOL statement
from the saved WACOL command.
4. In the WACOL shell, right-click on the command line
box and select paste.

9-10 WAVES Installation and Operation Manual

 The Scheduler

9.3 THE SCHEDULER

The Scheduler permits you to schedule the execution of a
WAVES procedure at a pre-defined time or at pre-defined
intervals. It is similar to the WACOL Shell in that it permits
you to execute the procedures using WACOL statements.

For example, using the Scheduler, you can raise the volume of
all the transceivers in a particular sub-zone every day at a 12:00
PM or you can transmit a pre-recorded message every hour
from 9:00 AM to 5:00 PM over a two-week period.

³ To schedule a WAVES procedure:

1. On the View menu, click Scheduler.
The Scheduler dialog box opens.

2. On the Description list, double-click <new event>.

3. On the Date and Time box, click <new time> to open
the Date and Time dialog box, type the date and time
you want to execute the procedure and then click OK..

WAVES Installation and Operation Manual 9-11

Advanced Features

4. If you want to schedule the procedure for more than one

time, do the following:
a. Click the Repeat Event box and then define how
often you want to repeat the procedure.
b. Click the Until box, click Date and Time to open
the Date and Time dialog box, type to which date
and time you want the procedure to repeat and then
click OK.
5. In the Description box, type a descriptive name.
6. In the Command box, type a WACOL statement.
Note: For a description of the WACOL syntax and a
list of WACOL statements, see Section 9.1.1.
7. Click OK.
WAVES schedules the procedure and the inserts the
descriptive name on the top line of the Description list.

³ To delete a scheduled WAVES procedure:

1. On the View menu, click Scheduler.
The Scheduler dialog box opens.
2. On the Description list, click a scheduled procedure.
3. Click Delete.
WAVES cancels the scheduled procedure and deletes its
name from the Description list.

9.4 ALTERNATE BASE STATION

When configuring a unit as SRLU, it can also be an alternate
base station by using a switch that shorts pin 10 of J2 to pin 3
(ground) of J2.

When pin 10 is shorted to the ground, the following occurs:

1. The SRLU sends a message to the CRLU (base station) that
it is switching to CRLU mode as an alternate base station.
2. If the CRLU responds, the SRLU switches immediately to
CRLU mode. If the CRLU doesn’t respond, the SRLU
switches after a 10 seconds timeout to CRLU mode.

9-12 WAVES Installation and Operation Manual

 Alternate Base Station

3. The CRLU (of the base station) change its mode to PRLU.

Note: These changes take affect only until

re-booting the system.

³ To return the system to normal mode:

1. If a PC with WAVES application is installed at the
alternate base station, send a message to the CRLU (of
the base station) to change back its mode to CRLU.
– or –
send a reboot message to the CRLU (of the base
station).
2. If no PC is installed at the alternate base station, turn
off the power of CRLU (of the base station) and turn it
on to reboot the unit.
3. Disconnect the ground from pin 10 of J2 of the SRLU
(of the alternate base station). The unit changes its
configuration from CRLU to SRLU.

WAVES Installation and Operation Manual 9-13

CHAPTER 10

THE RS-232 DATA

CHANNEL

This chapter includes the following sections:

x General
x Opening a link from the base station
x Opening a link from the field

WAVES Installation and Operation Manual 10-1

The RS-232 Data Channel

10.1 GENERAL
You can open a full duplex link between the data device
connected to the RS-232 connector on the CRLU and a data
device connected to the RS-232 connector on a field
transceiver.

Make sure that data devices connected to the CRLU and/or field
transceivers have the following settings:
x Baud rate: 9,600 bps
x Data bits: 8
x Stop bit: 1
x Parity: None
x flow control: cts/rts

10.2 OPENING A LINK FROM THE BASE

STATION
³ To open a full duplex link from the CRLU:
1. If you are in Off-line mode, click On-line on the Mode
menu to change to the On-line mode.
2. On the site tree, click a unit to which a data device has
already been connected.
3. On the Commands menu, click Open Link.
The CRLU places the unit on link standby by registering
its address as the destination for an upcoming link and the
On-hook Link icon appears to the left of the unit on the
site tree.
When the CRLU receives RS-232 data, it automatically
opens a full duplex link to the unit on link standby. The
Off-hook Link icon replaces the On-hook Link icon to
the left of the unit on the site tree.
WAVES automatically closes the link after a defined
period of silence (see Chapter 6) has expired, and the
On-hook Link icon appears to the left of the unit on the
site tree.

10-2 WAVES Installation and Operation Manual

 Opening a link from the field

Off-hook On-hook

Figure 10-1 Link Icons

³ To open a uni-directional link to the site or to a

zone or sub-zone:
1. If you are in Off-line mode, click On-line on the Mode
menu to change to the On-line mode.
2. On the site tree, click the site or a zone or sub-zone.
3. On the Commands menu, click Open Link.
The CRLU places the zone or sub-zone on link standby by
registering its address as the destination for an upcoming
link and the On-hook Link icon appears to the left of the
zone or sub-zone on the site tree.
When the CRLU receives RS-232 data, it transmits the
data to all the RS-232 devices in the zone or sub-zone.
The Off-hook Link icon replaces the On-hook Link
icon to the left of the zone or sub-zone on the site tree.
WAVES automatically closes the link after a defined
period of silence has expired, and the On-hook Link
icon appears to the left of the unit on the site tree.

10.3 OPENING A LINK FROM THE FIELD

³ To open a full duplex link from the field:
1. Connect a DCE or DTE link cable to the transceiver’s
RS-232 connector on one end and to the data device on
the other end.
2. Send data.
The CRLU can only support one link at a time. If
another link is already active, the CRLU denies access
to the new link.
When the CRLU grants access to the new link, the Off-
hook Link icon replaces the Unit icon to the left of the
unit on the site tree.

WAVES Installation and Operation Manual 10-3

The RS-232 Data Channel

WAVES automatically closes the link after a defined

period of silence has expired, and the Unit icon appears
to the left of the unit on the site tree.

³ To block a link initiated from a field transceiver:

1. If you are in Off-line mode, click On-line on the Mode
menu to change to the On-line mode.
2. On the site tree, click a unit to which a data device has
already been connected.
3. On the Commands menu, click Disable Link.
The field transceiver is blocked and can no longer initiate a
link to the CRLU. The Disable Link icon appears to the
left of the unit on the site tree only if the unit is marked
with a telephone icon.

Notes: a) Blocking a field transceiver cuts off any existing

link between the field transceiver and the CRLU.
b) To verify that the link to the unit is enabled, open
the Bit Result window and see the parameter
“Link Enable”.

10-4 WAVES Installation and Operation Manual

CHAPTER 11

ICM-501 - INTERCOM
CONTROL MODULES

This chapter includes the following sections:

x General
x ICM-501 description
x Installing the ICM-501
x Operating the ICM-501
x Using the intercom utility program

WAVES Installation and Operation Manual 11-1

ICM-501 - Intercom Control Modules

11.1 GENERAL
Using the intercom unit, you can:
x Establish telephone communication between the base
station and a field transceiver (TRX-401).
x Make an announcement (voice message) from a field
transceiver to the WAVES network.
x Establish unidirectional communications to monitor the
audio at any field node.

The ICM-501 has two types:

x ICM-501b - Intercom control unit for the base station
x ICM-501f - Intercom control unit for a field transceiver.

The ICM-501 also includes an Intercom Utility program that

runs on the base station’s PC. The intercom utility enables
software updates and configuration of the ICM-501f.

RLX

Base Station

C R L U -201

IC M -5 01F
D ata + A udio

D ata
A D U -301

D ata (R S -2 32)

IC M -50 1F

Figure 11-1 Intercom Application

11-2 WAVES Installation and Operation Manual

 ICM-501 Panel Description

11.2 ICM-501 PANEL DESCRIPTION

The ICM-501 panels include the following connectors:
x J1, RS-232 connector (D-type 9 pin, male) to connect (in
daisy chain connection) a display sign or another RS-232
device to the TRX.
x J2, ADU/TRX-401 connector (D-type 15 pin, male) to
connect the ICM-501 to the ADU (in base station) or a field
transceiver.
x J3, ACCESSORIES connector (D-type 15 pin, female) to
connect to user accessories (see section 11.4 ICM-501
External Interface).
x J4, TEL connector for future uses.

ADU/ TE L
R S -2 3 2 T R X -A D I A C C E S S O R IE S

J1 J2 J3 J4

Figure 11-2 ICM-501 Panel

11.3 INSTALLING THE ICM-501

The ICM-501b package includes:
x ICM-501b - Intercom unit for the base station
x Cable CAB-ICM/ADU-2

The ICM-501f package includes:

x ICM-501f - Intercom unit for a field transceiver
x Cable CAB-ICM/TRX-0.2

WAVES Installation and Operation Manual 11-3

ICM-501 - Intercom Control Modules

CAB-ICM/ADU-2 CAB-ICM/TRX-0.2

Figure 11-3 ICM-501 Cables and Connectors

11.3.1 MOUNTING THE ICM-501 ON THE TRANSCEIVER UNIT

Before installing the ICM-501f, mount the ICM-501f on the
transceiver unit (TRX-401).

³ To mount the ICM-501f on the TRX-401:

1. Disassemble the TRX-401from it’s mounting plate.
2. Disassemble all four mounting pins including the
square nuts (items 1 and 2) from the TRX-401 unit (see
Figure 11-4, step A).
3. Remove the two gauges (item 3) from the TRX-401
unit.
4. Disassemble the two sockets set screws and their
square nuts (items 2 and 4) from the ICM unit (see
Figure 11-4, step B).
5. Assemble the two sockets set screws and their square
nuts (items 2 and 4) to the TRX-401 unit (see Figure
11-4, step C).
6. Assemble the two mounting pins with the square nuts
(items 1 and 2) to the edge of the ICM unit (see Figure
11-4, step D).

11-4 WAVES Installation and Operation Manual

 Installing the ICM-501

7. Insert the two gauges (item 3) to maintain exact

distance between the mounting pins, and then insert the
other two mounting pins with the square nuts to the
other edge of the ICM unit.
1
TRX/CRLU ICM

2 1 2 4

2 1

S te p A S tep B

2 4 2 1

2 1

S te p C S tep D

Figure 11-4 ICM-501 Mounting on a Transceiver

Figure 11-5 ICM-501 Mounted on a Transceiver

WAVES Installation and Operation Manual 11-5

ICM-501 - Intercom Control Modules

11.3.2 INSTALLING THE ICM-501F

Figure 11-6 illustrates the wiring diagram for connecting the
ICM-501f to the TRX-401.
IC M -501f
ADU/ TE L
R S -2 3 2 TR X -A D I

J1 J2 J3 J4

LE D sign

C A B -T R X /IC M 0.2
or
O th er R S-232 D evise

IC M -TEL
3 Intercom
6
H andset
9
RS-232
#
J1
11 10 9 8 7 6 5 4 3 2 1
A MP O U T +15V I/O LINE O UT
J4
J2
J6
+12 VDC

Spe akers
J5

TR X-401
A C L in e In

Figure 11-6 TRX-401 Wiring Diagram including ICM-501f Connections

³ To connect the ICM-501f to a transceiver:

1. Loosen the screws on both sides of the transceiver’s
plastic case and slide the bottom cover off.
2. Insert P1 connector into the J4 (RS-232) connector on
the bottom panel of the transceiver.
3. Insert P4 connector in the J2 female connector on the
bottom panel of the transceiver.
4. Connect P2 to J2 (ADU/TRX) of the ICM-501f.

11-6 WAVES Installation and Operation Manual

 Installing the ICM-501

5. Connect the cable of the intercom handset to the

Accessories port of the ICM-501f.
6. Replace the bottom cover of the transceiver and tighten
the screws on both sides to secure it to the plastic case.

WAVES Installation and Operation Manual 11-7

ICM-501 - Intercom Control Modules

11.3.3 INSTALLING THE ICM-501B

Figure 11-7 illustrates the wiring diagram for connecting the
ICM-501b to the base station.

M ic External P TT
(option al)

Sp eakers (optional)

MIC.INPU T M ON ITOR
V O L UM E OUT A PEAK
M IC PT T TR IM
B PEAK
M IC . P E A K

ADU-30 1
-20 0 MIN MA X
C ON

A DU-301 _ FRON T PA NEL

_
AD U-301 REAR PAN EL
C H A NN E L A L INE IN P U T CH A N N E L B L IN E INP U T P C S O UN D C A RD D ATA P O RTS S Y NC IC M

P E A K C LIP P E A K C LI P IN OU T
PA D PA D R S -2 32 to C RL U R S -2 32

T R IM TR IM F R OM TO to C R LU to P C C on tro l

AC Line In

ADU- ADU-
R S 232 IC M

IC M -T E L
C A B -A D U-2 5/9-C R L U -4

C AB -AD U-IC M -2

3
6
Aud io S ource A 9
#
Aud io S ource B

Interc o m
CA B-A D U -SB -3

H a nd se t

A D U/ T EL
R S-232 ADU R S -23 2 TR X -A DI A C C E S S OR IE S

C R LU -2 01 J1 J2 J3 J4

IC M -5 0 1b
Com2 C A B-PC -AD U -3

P C w ith W AV E S S oftw are

(optional)

Figure 11-7 Base Station Wiring Diagram including ICM-501b Connections

11-8 WAVES Installation and Operation Manual

 ICM-501 External Interface

³ To connect the ICM-501b to the ADU-301:

7. Verify that the base station is installed with double-
headed cable: CAB-ADU-25/9-CRLU-X (where X
represents the length in meters).
8. Connect cable CAB-ADU-RS232/ICM-2 as follows:
– P2 to J2 of the ICM-501b
– P3 to RS-232 data port of the ADU-301
– P1 to ICM port of the ADU-301
9. Connect the cable of the intercom handset to the
Accessories port of the ICM-501b.

11.4 ICM-501 EXTERNAL INTERFACE

The ICM-501 ACCESSORIES (J3) connector enables
connecting one of the following:
x MADAH-Com handset for the ICM-501 application.
x Customized accessories that consist of the following
separated components: microphone, speaker for hands-free
application, call button, potentiometer, LED’s etc.
The following table describes J3, connector pins and electrical
ratings:
Pin no. Function Level Remark
1 MIC IN 28 – 280 mVptp Unbalanced mono input – Intercom
(hands-free) (10 – 100 microphone, audio compressed input,
mVrms) half duplex with speaker.
Impedance – 20 K:.
2 B_sper output TTL To ringers with operating voltage of
(Ringer) 5 Vdc, 20 mA max.
3 Pick_up input Normally open, Can be programmed to momentary or
pulled up input continuous operation.
4 Vol-speaker 0 – 1 Vdc External potentiometer (10 K:) for
input speaker volume control.
5 Spare output TTL Functional port of 5 Vdc, 20 mA
max for future uses.
6 GND 0V
7 MIC IN 58.8 – 280 mVptp Unbalanced mono input – Handset
(Handset) (21 – 100 microphone, not compressed, full
mVrms) duplex enabled.
Impedance – 20 K:.

WAVES Installation and Operation Manual 11-9

ICM-501 - Intercom Control Modules

Pin no. Function Level Remark

8 Monitor input Normally open, To monitor the ICM-501f from the
pulled up input base station.
9 Vol-ringer 0 – 1 Vdc External potentiometer (10 K:) for
input ringer volume control.
10 Spare input Normally open, Spare input for future input.
pulled up input
11 Power output 15 Vdc
12 LED – output 12.5 mA current To connect to – pin of a LED to the
limit ground.
13 Paging – input Normally open,
pulled up input
14 Speaker + 2 Vrms Earphone/Amp (4 :) balanced
output output
15 Speaker – 2 Vrms Earphone/Amp (4 :) balanced
output output

11.5 OPERATING THE ICM-501

The ICM-501 takes advantage of the full duplex link capability
between the CRLU and a field transceiver. When using
MADAH-Com handset, you can perform the following
procedures:
x Placing a call from a field transceiver to the base station
x Placing a call from the base station to a field transceiver
x Making an announcement (voice message) from a field
transceiver
x Monitoring audio at a field intercom

³ To place a call from a field transceiver to the base

station:
1. Lift the handset and listen to the ringing dialing tone
and/or the LED blinks (on for 1 second and off for 3
second). In case the link is busy, you here a busy tone
and the LED blinks (on for 1/2 second and off for 1/2
second).
2. If someone answers, the “Link” light (red LED) turns
on and you can talk to the person on the other end.
3. Place the handset in its cradle to hang up.

11-10 WAVES Installation and Operation Manual

 Operating the ICM-501

³ To place a call from the base station to a field

transceiver:
1. On the site tree, click the unit to which you want to
place a call and to which an ICM-501f has already been
connected.
2. On the Commands menu, click Open Link.
3. Lift the handset and listen to the ringing dialing tone
and/or the LED blinks (on for 1 second and off for 3
second). In case the link is busy, you hear a busy tone
and the LED blinks (on for 1/2 second and off for 1/2
second).
4. If someone answers, the “Link” light (red LED) turns
on and you can talk to the person on the other end.
5. Place the handset in its cradle to hang up.

³ To make an announcement (voice message) from a

field transceiver:
1. Press and hold the Paging button (red) on the handset
connected to the ICM-501f.
2. Pick up the handset.
3. Make an announcement.
4. Release the Paging button.
5. Place the handset in its cradle to hang up.
Note: In case of using local speakers for ICM-501, you
can page from an ICM-501b at a base station to all
ICM-501f’s at field stations.
³ To monitor audio at a field intercom:
1. On the site tree, click the unit to which you want to place
a call and to which an ICM-501f has already been
connected.
2. On the Commands menu, click Open Link.
3. Press and hold the monitoring button on the ICM-501
handset.
4. Lift the handset and release the Monitoring button.
5. Listen to the audio monitored of the ICM-501f.
6. Place the handset in its cradle to hang up.

WAVES Installation and Operation Manual 11-11

ICM-501 - Intercom Control Modules

³ To control the handset speaker volume:

x During conversation, rotate the VOL-SPK knob to tune
the volume as necessary.

³ To control the ringing volume:

x During ringing, rotate the VOL-RNG knob to tune the
ringing volume as necessary.

11-12 WAVES Installation and Operation Manual

 Using the Intercom Utility Program

11.6 USING THE INTERCOM UTILITY PROGRAM

The Intercom Utility program enables you to download the
software to the ICM-501 unit, and to configure the internal
parameters.

The Intercom Utility is applicable in one of the following

applications:
x Direct connection between the RS-232 interface of the
PC/notebook to the RS-232 interface of the ICM-501.
x Wireless link from the base station – connection between
the serial communication port COM1 or COM2 of the PC
to the RS-232 input of the ADU using CAB-RS232-DTE
cable.

Click the Intercom1shortcut icon. Main window appears.

Set Internal
Parameters

Peep

Version Update

Utility Setting
(password protected)

About Intercom1

Exit

Now you can perform the following:

x Set the Communication with the ICM-501
x Download the ICM-501 Software
x Set the ICM-501 Internal Parameters

WAVES Installation and Operation Manual 11-13

ICM-501 - Intercom Control Modules

11.6.1 SETTING THE COMMUNICATION WITH THE ICM-501

³ To set the communication with the ICM-501:
1. On the main window, click the Utility Setting icon.
The Utility Settings dialog box appears.

2. Set the communications port to an available one

(COM1 or COM2).
3. Set the Boudrate to 9600 bps.
4. Under Environment, select Save Last Settings check
box.
5. Click the Exit icon to exit the program and open it
again. Now you can communicate with the ICM-501.

11-14 WAVES Installation and Operation Manual

 Using the Intercom Utility Program

11.6.2 DOWNLOADING/UPDATING THE ICM-501 SOFTWARE

³ To download or update the ICM-501 software:
1. On the main window, click the Version Update icon,
The Version Update Procedure dialog box appears.
Browse
button

2. Enter the HEX file name of an appropriate intercom’s

firmware, or find the file using the Browse icon.
3. Click the Start button. The Intercom’s software is
updated.

WAVES Installation and Operation Manual 11-15

ICM-501 - Intercom Control Modules

11.6.3 SETTING THE ICM-501 INTERNAL PARAMETERS

You can set the following internal parameters in the ICM-501:

Operation mode – Handset with normal input microphone, or

Hands-Free with microphone connected to an audio compressor
(soft limited).

Phone mode – Field or Base. In field mode, Disconnect

parameter can be either Disabled or Enabled. In base mode you
cannot change the Disconnect parameter (it is always enabled).

Disconnect – Disable or Enable. Select Disable when using a

temporary switch as the Push-to-call button (as part of the
accessories connection). Select Enable when using a handset
that includes a push-to-call button (off-hook).

Remote phone – N/A, future use.

Ringer mode – External or Internal. Select External when using

an external ringer (+5V, 20mA). Select Internal when using the
handset earphone as a ringer.

³ To set the ICM-501 internal parameters:

1. On the main window, click the Internal Parameters
icon. The Password dialog box appears.

2. Enter the password (default is “waves”) and click OK.

The Peep Internal Parameters dialog box appears.

11-16 WAVES Installation and Operation Manual

 Using the Intercom Utility Program

3. Select the parameter you want change from the list, and
then click the arrow to change the settings for that
parameter.
4. Repeat step 3 for the rest of the parameters that you
want to change.
5. Click the Send button. The ICM-501 internal parameter
settings are updated.
6. To verify successful settings, click the Peep button.

7. Click the Exit icon to exit the program.

WAVES Installation and Operation Manual 11-17

CHAPTER 12

WAVES EXTERNAL
INTERFACES

This chapter includes the following sections:

x OLE interface
x DTMF control application
x RS-232 interface

WAVES Installation and Operation Manual 12-1

WAVES External Interfaces

12.1 OLE INTERFACE

WAVES application enables access from other applications
through the OLE (Object Linked Embedded) interface. For
example: you can activate WACOL commands from a touch-
tone telephone (see section DTMF Control Application)

³ To enable the OLE interface, do the following:

1. Copy the following C-Builder 3.0 files to WAVES
directory:
– Borlndmm.dll
– Cp3240mt.dll
– Vc135.bpl
2. Copy the following MADAH-Com files to WAVES
directory:
– WacolServer.dll
– misc.bpl
3. Register the WacolServer.dll according to your
development environment. For example, in Visual
Basic, from the Tools menu, select References and in
this dialog box register the WacolServer.dll.
4. Define the WacolServer.dll as your OLE inproc server
according to your development environment. WACOL
Server Query is available as OLE dual-interface.
5. Verify that the content of the WACOL Server Query is
as follows:
Properties: Address – Integer
ClientName – BSTR
Query – BSTR
Response – BSTR
Result – Integer
Timeout – Integer
Methods: DoQuery (no arguments)
Now you can use the OLE interface. For example, to perform
the WACOL command: report = ”OLE to WAVES”, write in
Word Basic (or Visual Basic) the following:
Sub RunOleToWaves()
Dim a As New WacolServer.Query
a.Query = “report=”““OLE to waves”””
a.DoQuery
End Sub

12-2 WAVES Installation and Operation Manual

 DTMF Control Application

12.2 DTMF CONTROL APPLICATION

12.2.1 INTRODUCTION
The DTMF control add-on application enables you to activate
the WAVES system from a touch-tone telephone using pre-
defined menu commands.

The DTMF control application consists on the following:

x Dialogic PROLINE/2V telephone card installed in the PC
(CNU).
x DTMF software installed in WAVES folder.

Note: DTMF control application is supported by Windows NT

only.

12.2.2 PRINCIPLE OF OPERATION

When calling the extension number where the Dialogic card is
connected to, the following happens:
1. The DTMF application answers with pre-recorded
messages and menus.
2. The caller is asked to provide a password.
3. After providing the password, the DTMF application run a
menu with the available commands.
4. The caller selects the required commands.
5. If necessary, the caller is asked to provide more information
according to the selected command.
6. At the end of this session, the DTMF application performs
the command/s through WAVES system.
Note: If a call session ends without pressing ‘#’, the line
remains busy until timeout (10 seconds) is expired.

WAVES Installation and Operation Manual 12-3

WAVES External Interfaces

The DTMF application default commands are as follows:

Key Command
1 Paging

2 Sending pre-recorded messages

3 Activating EMERGENCY mode

4 Deactivating EMERGENCY mode

12.2.3 INSTALLING THE DIALOGIC TELEPHONE CARD

The Dialogic telephone card is shipped with a CD-ROM
including the setup files and on-line documentation. Before
installing the card in the PC, check the available system
resources (IRQ and Base address resources) and prepare the
Dialogic card.

Note: It is recommended to remove the existing sound card

before installing the Dialogic telephone card and
reinstall it after successful installation of the Dialogic
telephone card.

12-4 WAVES Installation and Operation Manual

 DTMF Control Application

³ To check the available system resources and

prepare the Dialogic card:
1. From the Start menu, select Program –
Administrative Tools – Windows NT Diagnostics.
2. Select the Resources tab. The Resources tab appears.

3. Locate an available IRQ to configure the Dialogic card

(you can select the following IRQ’s: 3, 4, 5, 7, 10, 11
and 12).

Note: It is recommended to use IRQ 5 if possible. If it

conflicts with the sound card as often hapens, select
another available IRQ for the sound card.
4. Using the jumpers set the IRQ on the Dialogic card, to
the selected IRQ.
5. Set the Base Address and Offset on the Dialogic card if
needed (usually, the default settings are suitable).
6. Close all programs and shutdown the computer.

WAVES Installation and Operation Manual 12-5

WAVES External Interfaces

³ To install the Dialogic card in the PC:

1. Install the Dialogic card in available slot.
2. Turn on the PC.
3. Install the Dialogic software from the CD-ROM.
4. Restart the PC.
5. Open the Dialogic program group and run the Dialogic
Configuration Manager (DCM) application. A “No
Device Configured” message appears.
6. Select Add Board and follow the on-screen
instructions. During this process, set the IRQ and
memory address settings as configured on the card.
7. If the installation does not complete successfully, try
again, using manual selection and configuration.
8. In the configuration manager dialog box, click on
Services then Startup and select Automatic
(recommended).

Note: When selecting Automatic startup, the service is

activated automatically each time the computer is
restarted. When Selecting Manual startup, each time
the computer is restarted, you need to start the service
manually by selecting Start Service from the Service
menu.
9. Connect a telephone cable between the Dialogic card
RJ-11 connector to a touch-tone telephone or to a
telephone line (see Figure 12-1).
10. Connect a cable between the Dialogic card connector to
the ADU.

R J-11
Ph one Line
2 1 O utlet

D ia logic PR O LIN E /2V

Te le phone card
P hone Line C able

Figure 12-1 DTMF Control Connection

12-6 WAVES Installation and Operation Manual

 DTMF Control Application

³ To install the DTMF application:

1. Insert the diskette containing the DTMF application to
your floppy drive.
2. Run the Setup program and follow the on-screen
instructions.

12.2.4 SETTING THE DTMF CONTROL APPLICATION

The DTMF Control Application consists of the following three
tabs:
x Parameters
x Command
x Prompt

12.2.4.1 Parameters Tab

In the Parameters tab, you can set the following:
x Common prompts *.WAV files
– Welcome and request for password message
– WAVES commands menu
– Before recording message
– After recording message
x Connection parameters
– Password tones sequence
– Timeout in seconds
– Delimiter sign (usually *)
– End of call sign (usually #)
x Command storage
– Database alias
– Command database
– Prompts database

WAVES Installation and Operation Manual 12-7

WAVES External Interfaces

12.2.4.2 Prompts tab

In the Prompts tab, you can set for each DTMF code a *.WAV
file.

12-8 WAVES Installation and Operation Manual

 DTMF Control Application

³ To add a prompt:
1. Click the Insert button.
2. In the Code box, type an index number for the prompt.
3. In the Description box, type a description for the
prompt.
4. In the File box, type the name of the .WAV file to be
executed.
5. Click the Apply button.

Note: When recording a prompt message, use the following

format: PCM 11.025 kHz, 8 bit mono.

12.2.4.3 Command Tab

In the Command tab, you can set the following:
x DTMF code to activate any WACOL command (for
example PTT).
In this example, the application starts a default pre-recorded
menu that prompts the user to record a message (before-
record.wav) and continue with end of record message
(after-record.wav) before sending the message to WAVES
system.
x Next command code (option field).
In this example, the code 11 is PTToff. It is sent after the
message is played back. This command is required after
paging in order to return the system to normal mode.
x Internal command line. In this box, you edit the WACOL
command. The WACOL command consists of a statement
syntax, pre-recorded audio prompts and arguments for
interaction with the user.
In this example, the application sends prompt $P1 to
receive the zone number, then sends prompt $P2 to receive
the sub-zone number, and then sends prompt $P3 to receive
the unit number.

WAVES Installation and Operation Manual 12-9

WAVES External Interfaces

DTMF Command Format

The command format consists of a command code and
arguments list. The command code must be unique, otherwise
the DTMF control application will not execute the command.
The argument can be any number.

For example: to send an audiovisual message to a unit 12: Call

the DTMF control and enter 123*0*12#.
The command code is 123.
The WACOL command is Sendavm addr (0)= 12.
The internal command is Sendavm $P2 $A= $P3 $A (where $P
represents prompt and $A represents any numeric argument). ]

Commands with successive command

These commands must have a successive command in order to
end the session. For example: when using a paging command,
you need to use another command to end the paging session
(that mutes the speakers).

12-10 WAVES Installation and Operation Manual

 RS-232 Interface

³ To add a command:
1. Click the Insert button.
2. In the code box, type the DTMF code.
3. In the Next box, type the code number for the next
command if any.
4. In the Command box, type the WACOL command,
prompts and arguments.
5. Click the Apply button.
Note: You can browse the commands using the Prev and
Next buttons.

12.3 RS-232 INTERFACE

The RS-232 Interface application enables communication
between external devices and the WAVES System through the
RS-232 communications port.

WAVES includes application add-on that enables external RS-

232 devices connected to the RS-232 communications port, to
perform WACOL commands through WAVES OLE interface.

³ To install the RS-232 Interface application:

1. When installing WAVES application, select the
Custom option, and then select Add-Ons to be
installed.

³ To use the RS-232 commands:

1. In WAVES application, from Tools menu, select
RS-232 and set the COM port to an available one.
2. Restart WAVES application to accept the changes.
3. Connect a Null modem cable between the RS-232 port
and the external device.
4. Now you can use the RS-232 commands (see WAVES
RS-232 ICD document).

WAVES Installation and Operation Manual 12-11

APPENDIX A

VERSION UPDATE
PROCEDURE

This appendix includes a procedure for updating the

transceiver software version.

WAVES Installation and Operation Manual A-1

Version Update Procedure

Occasionally, you will receive a hexadecimal file containing an

update to the transceiver software version.

³ To update a transceiver’s software version:

1. Remove the transceiver’s power cable from its power
source to turn the transceiver off.
2. Connect one end of the CAB-PC-ADU-3 cable to your
PC’s serial port and the other end to the transceiver’s
RS-232 port.
3. Double-click the WAVES icon and open a WAVES file.

4. On the Mode menu, click Wired.

5. On the Commands menu, click Version Update.
6. The Version Update dialog box opens.

7. Under Hex File Name, enter the hexadecimal filename.

8. Click Update Version.
WAVES issues the “Waiting for ready to receive”
message.
9. Plug the transceiver’s power cable into its power source
to turn the transceiver on.
WAVES issues a series of messages documenting the
actions taking place. You can watch the progress of the
version update on the PC to Unit Progress and the
RAM to Flash Progress indicators.

A-2 WAVES Installation and Operation Manual

 Version Update Procedure

10. To verify successful installation, click Peep Unit Info

to open the Monitor and check the version number.

WAVES Installation and Operation Manual A-3

APPENDIX B

TROUBLESHOOTING

This appendix includes a list of problems that may arise

when using WAVES and possible solutions.

WAVES Installation and Operation Manual B-1

Troubleshooting

Following is a list of problems that may arise when using

WAVES and possible solutions. If a problem persists, contact
your MADAH-Com dealer.

The TRX Sync LED is blinking and no audio is heard.

The TRX is still in search mode.
x Verify that the TRX’ RF sources are turned on.
x Call the WAVES designer to reinitialize the TRX.

The System’s Condition Report dialog box reports that a

specific TRX’ BIT located an audio error.
Check that the speaker wires are not shorted to the TRX’ metal
body.

The WAVES software freezes.

Open WAVES and check the Site Properties dialog box to see if
WAVES has been configured to print online a hardcopy of the
log file (see Chapter 4). If it has, click the Write To check box
to disable online printing.

The System’s Condition Report dialog box reports that the

base station did not receive BIT results from a specific TRX
and that the TRX seems to be acting normally.
Problem with the back channel:
x Check the base station cables.
x Check that the cable is attached to the correct COM port.
x Check that the BIT report rate matches the total number of
units in your site.
x Check the back channel link and, if necessary, reinitialize
the transceiver’s included in the back channel link.

Text messages do not appear on the visual display sign.

Check the display’s parameters in the WAVES software:
x Verify that the display driver was installed correctly.

B-2 WAVES Installation and Operation Manual

 Troubleshooting

x Verify that the correct display driver was selected in the

AVM dialog box for the particular message.
x Verify that the transceiver’s display settings match the
selected display driver.

The audio signal to a TRX is unclear.

Check the reception quality of the TRX in the BIT Result. If the
RSSI value is below 140, assign a different primary and
secondary RF source to the TRX (see Chapter 4).

Background music from a TRX is periodically interrupted.

An audio BIT generates a sine signal which may be heard if the
audio settings of a TRX are lower than the required audio
threshold. To correct, either raise the audio level of the TRX or
cancel the Audio BIT (see Chapter 4).

A unit’s icon changes to the blue battery icon on the site

tree.
Indicates that the AC power supply to the TRX has been
interrupted and that the TRX is now receiving power from its
backup battery.

A unit’s icon changes to the red battery icon on the site tree.
Indicates that the backup battery power supply is low (has 10V
or less).

A unit’s icon changes to the blue battery with an “X” across

it on the site tree.
Indicates that the TRX does not have a backup battery even
though it is registered as having one.

No PC control over the field transceivers from the base

station.
x Verify that you are running WAVES in the On-line mode.
x Check the base station cables.

WAVES Installation and Operation Manual B-3

Troubleshooting

x Check that the cables are connected to the correct COM

port.

The System’s Condition Report dialog box reports

checksum errors on CRLU messages.
Reduce the CRLU’s BIT report rate.

Audio messages transmitted from the PC are not heard.

x Check that the PC sound card line output is connected to the
ADU via the PC SOUND CARD: FROM connector on the
ADU.
x Check the volume properties of your sound card.

Delay feedback during live audio announcements disturbs

the WAVES operator.
Connect a speaker at the base station to the Monitor connector
on the ADU.

The WAVES software crashes when the current .wvs file

cannot locate a specific .bmp file.

Import a different .bmp file and assign to it the filename the

.wvs file is searching for.

B-4 WAVES Installation and Operation Manual

APPENDIX C

TRANSMITTING OFFSET
ASSIGNMENTS

This appendix includes presents the recommended

transmitting offset assignment order for a WAVES site.

WAVES Installation and Operation Manual C-1

Transmitting Offset Assignments

An offset number is an RF frequency value assigned by you to a

CRLU-201 or TRX-401 to enable it to recognize which RF
signals to accept and which to ignore.

Offset numbers can be reused on the same site. To avoid

transmission difficulties, make sure that you do not assign
similar transmitting offsets to field transceivers defined as
PRLUs in the same area. For example, do not assign “5” and
“7” to two field transceivers located close to each other.

Note: Assign “0” as the transmitting offset of the CRLU and

“2” to those transceivers configured as RLXs on the
Internal Parameters tab of the Properties dialog box
(see Chapter 4).

The following table presents the recommended transmitting

offset assignment order for a WAVES site.

C-2 WAVES Installation and Operation Manual

 Transmitting Offset Assignments

Item Offset No. Item Offset No. Item Offset No.

CRLU 0 25. 60 51. 48
RLX 2 26. 12 52. 20
1. 31 27. 50 53. 64
2. 13 28. 66 54. 15
3. 53 29. 40 55. 49
4. 5 30. 9 56. 4
5. 23 31. 74 57. 58
6. 43 32. 36 58. 26
7. 67 33. 14 59. 51
8. 3 34. 30 60. 35
9. 37 35. 55 61. 62
10. 59 36. 38 62. 72
11. 11 37. 18 63. 54
12. 73 38. 63 64. 25
13. 47 39. 27 65. 42
14. 7 40. 44 66. 28
15. 17 41. 75 67. 68
16. 41 42. 21 68. 8
17. 71 43. 34 69. 39
18. 19 44. 52 70. 46
19. 29 45. 69 71. 32
20. 61 46. 16 72. 56
21. 70 47. 57 73. 1
22. 24 48. 33 74. 22
23. 45 49. 65
24. 6 50. 10

WAVES Installation and Operation Manual C-3

APPENDIX D

EQUIPMENT
SPECIFICATIONS

The following pages present the specification sheets for

the CRLU-201, ADU-301 and TRX-401.

WAVES Installation and Operation Manual D-1

APPENDIX E

CBU-721
CONTROL BOX

This Appendix includes the following sections:

x CBU-721 control box description
x Connecting the CBU-721 to WAVES system
x Operating the CBU-721 control box

WAVES Installation and Operation Manual E-1

CBU-721 Control Box

E.1 CBU-721 CONTROL BOX DESCRIPTION

The CBU-721control box enables controlling the WAVES
system when you want to quickly do the following:
x Sending addressed PTT
x Sending pre-recorded messages to an addressed unit
(through the CNU)
x Operating the Emergency mode
x Operating the Sirens mode

The CBU-721 includes a rechargeable battery. When

connecting the CBU-721, use a special cable that enables
voltage supply as well as recharging the battery.

The CBU-721 control box consists of LCD display and a

keypad (see Figure E-1). The keypad is programmed as follows:
x F1 key is defined as PTT function.
x F2 key is defined as Message function.
x F3 key is defined as emergency on function.
x F4 key is defined as Sirens menu function.
x ‘ENTER’ key is defined as execution button.
x ‘.’ key is used as a delimiter for approving a step, for
differentiating between the commands, and for moving
forward to the next field during command programming.
x ‘NO’ key is used for terminating the execution of a current
function.
x ‘BKSP’ is used to move backwards to a previous field
during command programming.
x ‘SPACE’ is used for broadcast PTT.

E-2 WAVES Installation and Operation Manual

 CBU-721 Control Box Description

The CBU-721 display consists of four lines. The upper two

lines are used for user communication (first line for terminal
messages and second line for command). The lower two lines
are reserved for reports and messages (e.g. EMERGENCY
mode).

F1 PTT F2 MESSAGES

F3 EMG F4 SIRENS

Note: If no key is pressed for one minute at any state, the

display returns to the main menu.

Figure E-1 CBU-721 Control Box

WAVES Installation and Operation Manual E-3

CBU-721 Control Box

E.2 CONNECTING THE CBU-721 TO WAVES

SYSTEM
The CBU-721 control box includes an RS-232 interface which
enables bi-directional communication with the RS-232 interface
of the CNU. The output of the CNU (other RS-232 interface) is
connected to the ADU (in PORTS interface) through the
interface switching box and from the ADU (in DATA interface)
to ADU interface of the CRLU-201. The CBU-SW1 switching
box enables quick connection through the ADU to the CRLU-
201 when the CNU is down.

The CBU-SW1 has two modes of operation:

Mode A – The CBU-721 is connected to the PC through

COM1, and returns to the ADU through COM2,
and from the ADU to the CRLU.
This mode is used to control the PC and its
resources. For example, to send pre-recorded
messages saved on the PC hard-drive.

Mode B – The CBU-721 is connected directly to the ADU,

and from the ADU to the CRLU.
This mode is used when the PC is out of order
and you need to use basic functions of WAVES.

³ To connect the CBU-721 to WAVES system:

1. Connect CAB-CBU721-SW1 cable from the CBU-721
to J1 of CBU-SW1.
2. Connect CAB-PC-ADU cable from J3 of CBU-SW1 to
the PC COM1 port.
3. Connect CAB-PC-ADU cable from the PC COM2 port
to J4 of CBU-SW1.
4. Connect CAB-ADU-SW1 cable from J5 of CBU-SW1
to the ICM port of the ADU.
5. Connect CAB-ADU-SW1 cable from J2 of CBU-SW1
to the PC Control port of the ADU.
6. Connect a CRLU cable from CRLU port of the ADU to
the ADU port of the CRLU.

E-4 WAVES Installation and Operation Manual

 Connecting the CBU-721 to WAVES system

C A B -PC -A D U -3
C A B -P C -AD U -3

CNU
J4 J3
C BU-SW 1
C A B -C B U -721-S W 1
CB U-721
J1
J1
R S -2 3 2
J2 J5
A M P O UT
11 10 9 8 7 6 5 4 3 2 1
+15V I /O LINE OUT
J4
C A B -A D U -S W 1
J2
J6
+12V DC
C A B-P C -A D U -3

J5
IC M
AD U-301 _ R EAR PANEL
CR LU-201 C HA NN E L A LIN E IN P UT C H AN NE L B L INE INP U T P C S O UN D CA RD D AT A P O RT S SYNC IC M

PEA KCL IP PE AKCL IP IN OUT

PA D PA D R S -23 2 t o C R L U R S -23 2

T RI M T RI M FR O M TO to CR L U to PC C on tro l

to PC C ontrol
to C R LU

Figure E-2 CBU-721 Control Box Connection

WAVES Installation and Operation Manual E-5

CBU-721 Control Box

E.3 OPERATING THE CBU-721

E.3.1 SENDING PTT BY ONE TOUCH KEY

³ To send PTT to a selected zone by one touch key:
x Press a number 1 – 9 that represents the required zone
for at least 1.5 seconds. This activates a PTT to that
zone only.

³ To send PTT to the entire site by one touch key:

x Press the ‘SPACE’ key or ‘0’ for at least 1.5 seconds.
This activates PTT for the entire site.
The display shows PTT ON.

E.3.2 SENDING ADDRESSED PTT

³ To send addressed PTT:
1. Press F1.
On the display appears: PTT Addr: 00.00.00

‘.’ Next ‘ENTER’ exe

The first two digits (zone field) flash.

2. Enter the zone number and press ‘.’.
The second two digits (sub-zone field) flash.
3. Enter the sub-zone number and press ‘.’.
The third two digits (unit field) flash.
4. Enter the unit number.
On the display appears:

‘.’ Next ‘ENTER’ exe

E-6 WAVES Installation and Operation Manual

 Operating the CBU-721

5. Press ‘ENTER’.
On the display appears: PTT ON for xx.xx.xx

Now you can announce through the WAVES system

while pressing the ‘ENTER’ key.

Options:
x Releasing the ‘ENTER’ key stops the PTT (voice off), and
on the display appears “PTT OFF”.
x Press the ‘ENTER’ key after any step during the address
input; the rest of the data remains 00.
x Pressing ‘BKSP’ key moves to a previous field.

E.3.3 SENDING PRE-RECORDED MESSAGES

³ To send pre-recorded messages:
1. Press F2.
On the display appears: MSG: 0 Addr: 00.00.00

‘.’ Next ‘ENTER’ exe

The first digit (message number) flashes.

2. Enter the message number (at the PC AVM) and
press ‘.’.
On the display appears: MSG: x Addr: 00.00.00

‘.’ Next ‘ENTER’ exe

The first two digits (zone field) flash.

3. Enter the zone number and press ‘.’.
The second two digits (sub-zone field) flash.
4. Enter the sub-zone number and press ‘.’.
The third two digits (unit field) flash.

WAVES Installation and Operation Manual E-7

CBU-721 Control Box

5. Enter the unit number.

On the display appears: MSG: x Addr: xx.xx.xx

‘.’ Next ‘ENTER’ exe

6. Press ‘ENTER’.
On the display appears: Message xx was sent to

xx.xx.xx

E.3.4 OPERATING THE EMERGENCY MODE

Emergency mode operates as defined in the WAVES system.
When the system is in emergency mode, the display shows
“EMERGENCY MODE”.

³ To activate the emergency mode:

1. Press F3.
On the display appears: SET EMERGENCY?

ENTER exe / NO cancel

2. Press ENTER (or NO to cancel).

On the display appears: EMERGENCY MODE

³ To cancel the emergency mode:

1. Press F3.
On the display appears: CLEAR EMERGENCY?

ENTER exe / NO cancel

EMERGENCY MODE

2. Press ENTER (or NO to cancel).

The message EMERGENCY MODE disappears.

E-8 WAVES Installation and Operation Manual

 Operating the CBU-721

E.3.5 OPERATING THE SIRENS MODE

³ To activate the siren mode:
1. Press F4.
On the display appears: 1. Steady1 2. Steady2

3. Alert 4. Chemical

2. Press one of the keys 1 – 4.

3. Press ENTER.
On the display appears: Are you sure?

ENTER exe / NO cancel

4. Press ENTER (or NO to cancel).

The PDS sends a siren command to the WAVES system.

WAVES Installation and Operation Manual E-9

APPENDIX F

COMFUTURE PROTOCOL
SETTINGS

This Appendix describes the ComFuture protocol and

how to prepare visual display messages with special
effects.

WAVES Installation and Operation Manual F-1

ComFuture Protocol Settings

You can prepare visual display messages with special effects

using the ComFuture protocol, store them in the visual display
sign’s memory and display them when they are needed. Storing
messages in the visual display sign’s memory enables you to
select a message at the site using the ComFuture keypad.

F.1 PREPARING AND STORING A MESSAGE

The ComFuture protocol supports single and countdown
messages. A single message is a text message that may cover
one or both lines of the two line text display. A countdown
message is a text message featuring a countdown clock
followed by two additional text messages that alternate in
appearance on the visual display sign. All three messages may
cover one or both lines of the two line text display.

Note: The ComFuture visual display has two lines. Each line
can support up to sixteen two-inch characters or eight
four-inch characters. The four-inch characters can
appear on one line or over two lines.

You can prepare an unlimited number of single and countdown

messages in the ComFuture protocol but you can only store up
to ten single and ten countdown messages in a visual display
sign’s memory.

You can also prepare a blank message in the ComFuture

protocol and store it in a visual display sign’s memory.

³ To prepare and store a single message:

1. On the View menu, click AVM Window.
2. In the Audio Display dialog box, click New.
“No Name” appears in the Name column.
3. Click “No Name” and type a descriptive name.
4. Click Displays.
The Remote Display Drivers dialog box opens.
5. Click ComFuture (ver 1.1) and then click Use.
The Remote Display Drivers dialog box closes and
ComFuture (ver 1.1) appears in the Display Signs box.

F-2 WAVES Installation and Operation Manual

 Preparing AND Storing a Message

6. Click ComFuture (ver 1.1) in the Display Signs box

and then click Edit.
The ComFuture Editor dialog box opens.

7. Select a message number, select Load Single Message,

and then click OK.
The Edit Single Message dialog box opens.

8. Type a message, modify the protocol settings, and click

OK.
WAVES translates the text into the ComFuture protocol
and closes the Edit Single Message dialog box.
9. Click OK to save the message and close the
ComFuture Editor dialog box.
10. In the Audio Display dialog box, select the new
message in the Name column, and then click Send.
WAVES loads the message into the visual display sign’s
memory.

WAVES Installation and Operation Manual F-3

ComFuture Protocol Settings

³ To prepare and store a countdown message:

1. On the View menu, click AVM Window.
2. In the Audio Display dialog box, click New.
“No Name” appears in the Name column.
3. Click “No Name” and type a descriptive name.
4. Click Displays.
The Remote Display Drivers dialog box opens.
5. Click ComFuture (ver 1.1) and then click Use.
The Remote Display Drivers dialog box closes and
ComFuture (ver 1.1) appears in the Display Signs box.
6. Click ComFuture (ver 1.1) in the Display Signs box
and then click Edit.
The ComFuture Editor dialog box opens.
7. Select a message number, select Load Countdown
Message, and then click OK.
The Edit Countdown Message dialog box opens.

8. Type a message for the countdown page and, if

required, type messages for one or both of the alternate
pages.
9. Modify the protocol settings for each page.

F-4 WAVES Installation and Operation Manual

 Preparing AND Storing a Message

Note: If you select the 4x4 inch parameter for Line 1

of the Count Down Page, the countdown clock
and the actual message alternate on the visual
display sign.
10. Under Count Down, type the starting point in minutes
and seconds for the countdown and select the location
of the countdown clock (right or middle).
11. Under Timing, type in the Flash box when you want
the time on the countdown clock to start flashing. For
example, if you type 10, the time on the countdown
clock will start flashing ten seconds before the end of
the countdown.
12. If you typed messages for the two alternate pages, type
a number in the Display box for how many seconds to
display each message and another number in the
Alternate box for how many seconds to display the two
alternate messages. For example, if you type 5 in the
Display box and 20 in the Alternate box, the two
additional messages will be displayed for 20 seconds
after the countdown message ends. Each message will
appear for intervals of 5 seconds.
13. Click OK to save the countdown message and close the
ComFuture Editor dialog box.
14. In the Audio Display dialog box, select the new
message in the Name column, and then click Send.
WAVES loads the message into the visual display sign’s
memory.

³ To prepare and store a blank message:

1. On the View menu, click AVM Window.
2. In the Audio Display dialog box, click New.
“No Name” appears in the Name column.
3. Click “No Name” and type a descriptive name.
4. Click Displays.
The Remote Display Drivers dialog box opens.
5. Click ComFuture (ver 1.1) and then click Use.
The Remote Display Drivers dialog box closes and
ComFuture (ver 1.1) appears in the Display Signs box.

WAVES Installation and Operation Manual F-5

ComFuture Protocol Settings

6. Click ComFuture (ver 1.1) in the Display Signs box

and then click Edit.
The ComFuture Editor dialog box opens.
7. Select Blank Display, and then click OK.
WAVES saves the message and closes the ComFuture
Editor dialog box.
8. In the Audio Display dialog box, select the blank
display message in the Name column, and then click
Send.
WAVES loads the message into the visual display sign’s
memory.

F.2 DISPLAYING A STORED MESSAGE

You can prepare and send messages commanding the
ComFuture driver to display a specified stored message.

Note: You can also connect the ComFuture keypad to the

visual display sign and press the appropriate keys to
display a specific message where:
00-09 = Single Message 1-10
10-19 = Countdown Message 11-20

³ To prepare and send display command messages:

1. On the View menu, click AVM Window.
2. In the Audio Display dialog box, click New.
“No Name” appears in the Name column.
3. Click “No Name” and type a descriptive name.
4. Click Displays.
The Remote Display Drivers dialog box opens.
5. Click ComFuture (ver 1.1) and then click Use.
The Remote Display Drivers dialog box closes and
ComFuture (ver 1.1) appears in the Display Signs box.
6. Click ComFuture (ver 1.1) in the Display Signs box
and then click Edit.
The ComFuture Editor dialog box opens.

F-6 WAVES Installation and Operation Manual

 Deleting Stored Messages

7. Select a message number, select Display Single

Message or Display Countdown Message and then
click OK.
WAVES saves the command as a message and closes the
ComFuture Editor dialog box.
8. In the Audio Display dialog box, select the new
message in the Name column and then click Send.
WAVES loads the message commanding the ComFuture
driver to display the specified stored message into the
visual display sign’s memory.

F.3 DELETING STORED MESSAGES

You can delete a stored message in the visual display sign’s
memory.

³ To delete a message:
1. On the View menu, click AVM Window.
2. In the Audio Display dialog box, click New.
“No Name” appears in the Name column.
3. Click “No Name” and type a descriptive name.
4. Click Displays.
The Remote Display Drivers dialog box opens.
5. Click ComFuture (ver 1.1) and then click Use.
The Remote Display Drivers dialog box closes and
ComFuture (ver 1.1) appears in the Display Signs box.
6. Click ComFuture (ver 1.1) in the Display Signs box
and then click Edit.
The ComFuture Editor dialog box opens.
7. Select a message number, select Delete Single Message
or Delete Countdown Message, and then click OK.
WAVES saves the command as a message and closes the
ComFuture Editor dialog box.

WAVES Installation and Operation Manual F-7

ComFuture Protocol Settings

8. In the Audio Display dialog box, select the deletion

message in the Name column, and then click Send.
WAVES sends the deletion message to the visual display
sign’s memory.

F-8 WAVES Installation and Operation Manual

APPENDIX G

LIST OF CABLES

This Appendix includes a table presents a list of cables

designed for the WAVES system.

WAVES Installation and Operation Manual G-1

List of Cables

The following table lists cables designed for the WAVES

system.

NAME CAT. NO. DESCRIPTION

CAB-PC-ADU-3 M50-02100 PC to ADU Cable (3m)
CAB-ADU-25/9-CRLU-4 M50-02110 ADU to CRLU 25+9 Pin Cable (4m)
CAB-ADU-25-CRLU-4 M50-02102 ADU to CRLU 25 Pin Cable (4m)
CAB-ADU-9-CRLU-4 M50-02109 ADU to CRLU 9 Pin Cable (4m)
CAB-ADU-SB-3 M50-02104 ADU to Sound Card Cable (3m)
CAB-MINI-COMB-3 M50-02114 Mini (1/8") Stereo Combine Cable (3m)
CAB-PL-COMB-3 M50-02107 PL (1/4") Stereo Combine Cable (3m)
CAB-RS232-DTE-3 M50-02101 DTE RS-232 Link Cable (3m)
CAB-RS232-DCE-3 M50-02105 DCE RS-232 Link Cable (3m)
CAB-UPS M50-02028 Single UPS Cable
CAB-UPS-D M50-02112 Double UPS Cable
CAB-RF-SMA-2 M50-02108 RF to Ext. Antenna SMA Cable (2m)
CAB-RF-N-2 M50-02106 RF to Ext. Antenna N-Type Cable (2m)
CAB-ICM-TRX-0.2 M50-02519 TRX to ICM-501 RS-232 and power cable
(0.2m)
CAB-ICM-ADU-2 M50-02518 ADU to ICM-501 RS-232 power cable
(2m)
CAB-ADU-SW1 M50-02899 ADU to SW1 power supply cable
CAB-CBU721-SW1 M5004001 SW1 to CBU-721 RS-232 and power
supply cable
CAB-CBU711-SW1 M50-02900 SW1 to CBU-711 RS-232 and power
supply cable

G-2 WAVES Installation and Operation Manual

APPENDIX H

EMA-211-WRX
INSTALLATION AND
OPERATION INSTRUCTIONS

This Appendix includes installation and operation

instructions of the EMA-211-WRX.

WAVES Installation and Operation Manual H-1