Resilient Seated Butterfly Valves: 2”-12”

Pneumatic Conveying & Abrasive Applications, Wafer & Lug Bodies

390
SERIES
393

®
390/393 SERIES
Ultraflo proudly offers the 390/393 Series Features Primary and Secondary Seals (B) The primary seal is formed by an inter-
butterfly valve – designed specifically for ference fit between the disc hub and the seat flat. The secondary seal is an
pneumatic conveying and abrasive interference fit between the stem and seat stem hole. The secondary seal also
applications. The valve characteristics incorporates a molded O-ring in the stem hole of each elastomer seat providing
include a seat designed specifically for increased interference and an added level of protection. These seals prevent line
schedule 40 piping, matching the seat media from coming into contact with other valve components. Ultraflo’s ultrathin
ID with the inside diameter of the pipe one-piece Disc/Stem (C) provides a high flow capacity with smooth flow charac-
wall. The result is smoother product flow teristics that greatly reduce line media pressure drops. The disc edge is CNC
and less abrasion of valve components. machined and hand polished to produce bubble tight shut off, minimum torque
Valve sizes range from 2” – 12” . and longer seat life. The Upper Stem Bushing (D) absorbs operator side thrusts, pro-
The 390/393 Series provides a bi- vides precision alignment to ensure less wear and lowers operating torque. The
directional pressure rating of 150 psi with Lower Stem Bushing (E) eliminates gaulding and frozen stems. Both upper and lower
stainless steel disc/stems and 100 psi bushings are heavy duty non-corrosive thermoplastic polymer. A Stem Packing (F)
with encapsulated disc/stems. Valves prevents external contaminants from entering the stem bore.
installed in dead end service (down- The Split Body (G) design simplifies field maintenance by eliminating the need
stream flange removed) are de-rated for special tools or presses during installation of replacement seats. All 300 Series
to 75 psi. Figure 390 valves are Wafer valve bodies are designed to fit between ASME/ANSI 125 or 150 lb. flanges.
style bodies offered in Stainless Steel, Body Recesses (H) accommodate lightweight flanges. Body Bolt (I) materials are zinc
Cast Iron and Aluminum. Figure 393 plated carbon steel or stainless steel as standard.
valves are Lug style bodies offered in
Stainless Steel and Nodular Iron.

Dovetail
Seat (A) Top Plate (J)
Flange
Seal
O-Ring Upper Bushing (D)

Stem Packing (F)

Elastomer seat. Section view at stem hole.

Disc/Stem (C)
Ultraflo’s resilient Seat (A) is the heart of
all 300 Series valves. The seat incorpo-
rates a dovetail retention system ensur- Body Recess (H)
ing positive alignment and ease of
assembly. All 300 Series seats include
Secondary Seal (B)
an integral flange seal molded into the
Primary Seal (B)
seat face providing a positive seal with
all popular flanges. In addition, an O-ring
is molded into the stem hole of each 300 Seat (A)
Series elastomer seat to provide an
added level of protection. Disc/Stem (C)

Split Body (G)

Body Bolts (I)

Lower Bushing (E)

390 Series
Buna Seat,
Stainless Steel Disc/Stem,
Wafer Style Body shown
390/393 SERIES
Ideally Suited for Pneumatic Components 390 Series Cast Iron
Conveying & Abrasive Applications Wafer Style Body
Item Description Qty.
The two-piece split body allows for a thin
1 Split Body 1
profile one-piece investment cast disc/ 4
stem with a smooth finish free of porosity, 2 Seat 1
voids or cracks. This design provides 3 Disc 1
complete protection from particle entrap- 4 Upper Bushing 1 5
ment, and in combination with schedule 5 Stem Packing 1
40 dimensioning, results in minimal line
6 Lower Bushing 1
media interference. For severely abra-
sive applications, Ultraflo offers disc/ 7 Body Bolt 2
stems in 17-4 ph as well as full elastomer 8 Lock Washer 2
encapsulation of the disc.
All sizes of Cast Iron, Nodular Iron Materials of Construction
and Aluminum bodies and 8”-12” Stain- Bodies: Cast Iron, Nodular Iron and
less Steel bodies have a CNC machined Investment Cast 316 Stainless Steel
Top Plate (J) with standardized drilling for in both wafer and lug style split
total actuator and operator interchange- bodies. Aluminum bodies are avail- 1
ability. A handle notch plate is supplied able in wafer only.
with the manual handle kit. Seats: Nitrile, White Nitrile, EPDM, Buna,
2”- 6” Stainless Steel valve bodies FKM, PTFE (select sizes).
feature an integrally cast Throttling Top Disc/Stems: 17-4 Stainless Steel
Plate with a self draining recess ensuring and Investment Cast 316
complete drainage of wash-down media. Stainless Steel.
Elastomer encapsulated and
other custom disc coatings
are available.
Upper and Lower Bushings:
Thermoplastic Polymer
Stem Packing: Buna-N
Body Bolts and Lock Washers: 2
Zinc Plated Carbon Steel
or Stainless Steel

3
Seats are available as standard in
Nitrile, White Nitrile, EPDM, Buna and 6
FKM. PTFE lined seats are available in
select sizes. Consult factory for availability.
All compounds other than FKM are FDA
approved. All Ultraflo valves are tested
to 110% of pressure rating for bubble tight 1
shut off before shipment.

All 390/393 Series valves are Temperature Range of Seats

designed to meet MSS SP67
dimensional standards. Type Minimum Maximum
EPDM -40°F +250°F
Buna 0°F +212°F
8
Nitrile -20°F +275°F
White Nitrile -20°F +275°F 7
PTFE -20°F +300°F
FKM 0°F +400°F
390/393 SERIES
Dimensions
Valve Size Lug Data
ins mm A B C D E F G H Q R S T U BC Tap
2 50 4.00 .375 .563 1.250 4.063 4.125 2.125 1.625 1.531 3.250 .438 2.760 .375 4.750 .625 -11
2 1/2 65 4.00 .375 .563 1.250 4.625 4.875 2.50 1.750 1.969 3.250 .438 2.760 .375 5.50 .625 -11
3 75 4.00 .375 .563 1.250 5.00 5.375 3.125 1.750 2.689 3.250 .438 2.760 .375 6.00 .625 -11
4 100 4.00 .438 .625 1.250 6.00 6.875 4.125 2.00 3.719 3.250 .438 2.760 .375 7.50 .625 -11
5 125 4.00 .500 .750 1.250 6.00 7.750 5.188 2.125 4.813 3.250 .438 2.760 .375 8.50 .750-10
6 150 4.00 .500 .750 1.250 6.625 8.750 6.125 2.125 5.813 3.250 .438 2.760 .438 9.50 .750-10
8 200 6.00 .625 .875 1.250 8.313 11.00 8.125 2.50 7.813 5.00 .563 4.020 .438 11.750 .750-10
10 250 6.00 — 1.125* 2.00 9.125 13.375 10.125 2.50 9.906 5.00 .563 4.020 .438 14.250 .875 -9
12 300 6.00 — 1.125* 2.00 10.645 16.125 12.094 3.00 11.844 5.00 .563 4.020 .438 17.00 .875 -9
All 390/393 Series are designed to meet MSS SP67 dimensional standards.
Notes:
øC
2"-8" Valves
B Flats
* 10"-12" Valves 1. 2”- 6” Stainless Steel Valve
Double D Stem Round Stem
Bodies have an integral
Dimensions Dimensions
Throttling Top Plate.
D 1/4" x 1/4" 8”, 10” and 12” SS Valves,
Note 1 Keyway
and all sizes Cast Iron,
øC Nodular Iron &
Lug Aluminum Valves have
E Valve standard Top Flanges,
A notch plates are supplied
45° with handle.
2. Bolt Circle T and Hole
Q G F H Diameter U meet
ISO 5211 standards
for Top Flange Drilling:
2”- 6” = F7
Note 2 øR Bolt Circle 8”- 12” = F12
øT Bolt Circle øS Not applicable to
øU Aluminum bodies.

Operator and Actuator Mounting Flange Requirements

Ultraflo has designed the 300 Series operator The valve O.D. and
mounting Top Flange to ISO 5211 specifica- flange bolt circle
tions for direct mounting of manual operators must share a common
and actuators. Designed to recognized indus- center line. The valve
trial standards, the Double D stem connection is designed to be
provides a secure connection with most placed between
actuators eliminating the need for brackets. ASME / ANSI 125 or
Ultraflo offers a wide range of automation 150 lb. flanges.
products including handles, gear operators,
rack and pinion pneumatic actuators, pneu-
matic cylinder and wrench arm assemblies,
electric actuators, pneumatic and electro-
pneumatic positioners, solenoids, valve posi-
tion indicators, proximity and limit switches.

The data represented in this brochure is for general informa- Ultraflo Corporation
tion only. Manufacturer is not responsible for acceptability of ® A Subsidiary of Bray International, Inc.
these products in relation to system requirements. Consult
your Ultraflo representative for specific performance data and 8 Trautman Industrial Drive
proper materials selection for your particular application. Ste. Genevieve MO 63670
800.950.1762 Fax 573.883.8882
© 2004 Ultraflo Corporation. All rights reserved. 390/393S 02/04 www.ultraflovalve.com