Republic of The Philippines: Department of Public Works and Highways Office of The Secretary

Q~i t \?
J t)1'\t\l \t
Republic of the Philippines
0\. 2~,1o~~
DEPARTMENTOF PUBLIC WORKS AND HIGHWAYS
CENTRAL OFFICE
Manila
JAN 2 7 2022
DEPARTMENT ORDER SUBJECT: Amendment to DPWH Standard
Specification for Item 607(3) -
NO.
Series of 2022
08& Internally Illuminated (Solar)
Pavement levelled Markers/Studs
Flush Type
In order to ensure uniformity in the application/ adoption of the Pay Items of Work to be
used/adopted by those who are involved in the preparation of the Design Plans and Quantities,
Program of Works (POW) and Approved Budget for the Contract (ABC) for Infrastructure
Projects Nationwide, the attached amended DPWH Standard Specification for Item 607(3)
- Internally Illuminated (Solar) Pavement Levelled Markers/Studs Flush Type is
hereby prescribed for adoption in Government infrastructure projects that require the
utilization of such in the Program of Works.
This Standard Specification shall form part of the DPWH Standard Specifications for Highways,
Bridges and Airports, Volume II and is now included in the Project and Contract Management
Application (PCMA).
This supersedes Memorandum 097.7 _050719 (Standard Specification for Item 607(3) -
Internally Illuminated (Solar) Pavement Levelled Markers/Studs Flush Type for Inclusion in
the DPWH Standard Specification for Item 607 - Reflective Pavement Studs) issued on May
7, 2019 and shall take effect immediately.
14.1.2 MLL/RPF
Department of Public Works and Highways
Office of the Secretary
1111111111111111111111111111111111111
WIN2U01742
Amendment to DPWH Standard Specification for
ITEM 607(3) - INTERNALLY ILLUMINATED (SOLAR) PAVEMENT LEVELLED
MARKERS/STUDS FLUSH TYPE
607(3).1 Description
This Item shall consist of furnishing and installing internally illuminated (solar) pavement
levelled markers/studs on the surface of the pavement in accordance with this Specification
and at the lines and locations shown on the Plans.
607(3).2 Material Requirements
607(3).2.1 Internally Illuminated (Solar) Pavement Levelled Markers/Studs
The internally illuminated (solar) pavement levelled markers/studs shall be either mono-
directional or uni-directional, bi-directional or omni-directional.
The reinforced body case shall be made of aluminum die cast with adequate webbing to
ensure a firm key to the road when installed. The protective upper cup or security ring shall
be made of aluminum die cast with a minimum of five (5) stainless steel safety locks.
The internal circuit module shall be detachable from the reinforced body case for easy
maintenance and shall be made of impact and abrasion resistant polycarbonate material which
is tightly sealed with its body having an Ingress Protection (IP) 68 rating (dust and water
resistant) based from IEC 60529, Degrees of protection provided by enclosures (IP Code).
The internally illuminated (solar) pavement levelled markers/studs shall conform to the
applicable requirements of EN 55015, Limits and Methods of Measurement of Radio
Disturbance Characteristics of Electrical Lighting and Similar Equipment, and EN 61547,
Equipment for General Lighting Purposes - EMC Immunity Requirements. The certified true
copy of the said test results shall be issued by the manufacturer to the Contractor reiterating
the current date of certification and must be submitted to the Engineer before doing the
installation work.
The solar cell and the rechargeable battery shall be of the latest technology and shall be able
to last for at least 3 days of LED runtime with a 12 hour per day discharge criteria on one (1)
full charge. The light-emitting diode (LED) shall have luminous intensity varying depending on
the color (yellow, white, red, green, and blue). For yellow and white, the minimum luminous
intensity values expressed in millicandela (mcd) is shown in Table 607(3).1. The LED shall
have an output frequency of either steady or flashing.
Table 607(3).1 Luminous Intensity Properties

Color
Luminanceintensity (mcd)
Yellow White
Vertical angle 0.2° / Horizontal angle 0° 350 400
Vertical angle 0.3° / Horizontal angle +5° 200 200
Vertical angle 0.3° / Horizontal angle -5° 200 200
Vertical angle 1.0° / Horizontal angle + 10° 100 100
Vertical angle 1.0° / Horizontal angle -10° 100 100
Amendment to DPWH Standard Specification for Item 607(3) - Internally Illuminated
(Solar) Pavement Leveled Markers/Studs Flush Type
Page 2 of 3
All LEDs should be covered with polycarbonate covers on the sides. Mono-directional or Uni-
directional Internally Illuminated (Solar) pavement levelled markers/studs shall either have
three (3) LED or a minimum of one (1) LED on one (1) tapering side. Bi-directional internally
illuminated (solar) pavement leveled markers/studs shall have a minimum of two (2) LEDs on
one (1) tapering side. Omni-directional internally illuminated (solar) pavement leveled
markers/studs shall have a minimum of three (3) LEDS on one tapering side and a minimum
of two (2) on two (2) opposite tapering sides.
Table 607(3).2 Specifications

Properties Requirements
Housing/Body Aluminum Die Cast
Diameter (Main Body), Min. 123 mm dia.
Height, Min. 39 mm
Weight, Min. 590 grams
Solar Panel, Min. Mono (Single) Crystalline 2.5V, 120mA
Anti-heat Lithium Iron Phosphate (LiFeP04)
Rechargeable Battery
3.2V, 1000-1500mAh
LED Chip, Min. 6mm
Gradient on LED Sides 30 degrees
Operating Temperature -20°C to 65°C
Compression Test, Min. 30 Tons
607(3).2.2 Adhesive
Any approved two-part epoxy adhesive shall be used in the installation of the internally
illuminated (solar) pavement levelled markers/studs.
607(3).3 Construction Requirements
The markers/studs shall be jnstalled into the pavement in accordance with the manufacturer's
instructions but shall also comply with the specified requirements.
Holes in the pavement shall be true to size of the marker/stud and shall be cleanly cut using
appropriate coring equipment. Holes shall be clean and free from all dirt, dust, oil, grease,
laitance, or any other materials, which would prevent bonding, prior to application of adhesive.
No adhesive shall be applied when the weather is foggy or rainy.
Placing and positioning of the marker/stud shall be by means of rubber mallet until the top
surface is flushed with the pavement and with the main directional LED light parallel to the
centerline of the road. Excess adhesive displaced during the placing and positioning of the
markers/studs shall be wiped clean and no adhesive shall be left exposed on the surface of
the pavement.
Traffic shall be kept off the newly installed markers/studs for a period of at least 2 hours or
until such time that the adhesive has sufficiently cured as determined by the Engineer.
Amendment to DPWH Standard Specification for Item 607(3) - Internally Illuminated
(Solar) Pavement Leveled Markers/Studs Flush Type
Page 3 of 3
607(3).3.1 Markings
Product marking (Manufacturer or applicable abbreviation and approval number) shall be clear
and firm by way of not erasing easily and to be seen easily for road studs.
607(3).3.2 Warranty
The Contractor shall obtain from the manufacturer a one-year warranty for satisfactory field
performance including stipulated luminous intensity of the LED and battery back-up capacity
and submit the same to the Engineer.
607(3).4 Method of Measurement

The quantity of internally illuminated (solar) pavement levelled markers/studs to be paid for
shall be the number of internally illuminated (solar) pavement levelled markers/studs of mono-
directional or uni-directional type, bi-directional type and omni-directional type, whichever is
called for in the Contract, installed complete and accepted.
607(3).5 Basis of Payment

The quantities measured as described in Section 607(3).4, Method of Measurement, shall be
paid for at the Contract Unit Price of the Pay Items shown in the Bid Schedule, which payment
shall constitute full compensation for furnishing and placing all materials, drilling of holes,
preparation of surfaces, applying adhesive and for all labor, equipment, tools and incidentals
necessary to complete the Item.
Payment shall be made under:
Pay Item Unit of

Description
Number Measurement
Internally Illuminated (Solar) Pavement Levelled
607 (3)a.l Marker/Stud Flush Type (Mono-directional or Uni- Each
directional), 123mm dia.
607 (3)a.2 Marker/Stud Flush Type (Mono-directional or Uni- Each
directional), 143 mm dia.
607 (3)b Each
Marker/Stud Flush Type (Bi-directional)

607 (3)c Each
Marker/Std Flush Type (Omni-directional)
References:
1. International E1ectrotechnical Commission (TEe)
• IEC 60S29, Degrees of protection provided by enclosures (IP Code)
2. European Standard (EN)
• EN SS015, Limits and methods of measurement of radio disturbance characteristics of electrical lighting
and similar equipment
• EN 61S47, Equipment for general lighting purposes - EMC immunity requirements
3. DPWH Standard Specification for Highways, Bridges, and Airports
4. erc Builder & Supplies Incorporated; Road Devices & Equipment Corporation (Exclusive Distributor in the
Philippines) / Green & Innovation (GU) Tech Co. Ltd (Korean Counterpart/Manufacturer/Principal)
5. Crownmix Corporation (Exclusive Distributor in the Philippines) / Miracle Ind. Co. Ltd (Korean
Counterpart/Manufacturer/Principal)
6. Technoshine Trading International

Republic of The Philippines: Department of Public Works and Highways Office of The Secretary

Uploaded by

Copyright:

Available Formats

Republic of The Philippines: Department of Public Works and Highways Office of The Secretary

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Republic of The Philippines: Department of Public Works and Highways Office of The Secretary

Uploaded by

Copyright:

Available Formats

Q~i t \?

607(3).2 Material Requirements

607(3).2.1 Internally Illuminated (Solar) Pavement Levelled Markers/Studs

Table 607(3).1 Luminous Intensity Properties

Table 607(3).2 Specifications

607(3).3 Construction Requirements

607(3).4 Method of Measurement

607(3).5 Basis of Payment

Payment shall be made under:

Pay Item Unit of

Internally Illuminated (Solar) Pavement Levelled

You might also like