M 3.

2/2/EN/ 2

Marine Fire and

Gas Dampers
Type JFD

Telephone + 6 06-678 8188

Telefax + 6 06-678 8288 / 388
E-mail [email protected]
www.troxapo.com
Contents · Description

Description 2 Accessories 6
Construction; Materials; Standard Sizes 3 Order Details 7
Product Range; Performance data 5

TROX Type ‘JFD’ Damper is a Multi-leaf Fire and The damper is also certified for use in Zone 1 and
Gas Damper, designed for marine and offshore 2 hazardous areas and complies with EU Directive
applications. The damper is certified by Lloyd’s 94/9/EG (ATEX 95), Appendix 1 and is classified
Register and ABS for the compliance with IMO under equipment group II, category 2G. In accor-
Fire Test Procedures Code, Annex 1; Part 3. The dance with EU Directive 99/92/EC (ATEX 137),
damper is also certified by Lloyd’s Register for the damper can be used in potentially explosive
compliance with the essential Fire protection environment where gas Groups IIA, IIB and IIC,
requirements of the EU Marine Equipment Direc- and flammable materials at temperature classes
tive (MED) 96/98/EC. The damper is certified for T1 to T6 are present.
horizontal or vertical mounting in ‘A-0’ divisions,
and ‘A-15’, ‘A-30’ and ‘A-60’ divisions when The maximum recommended operating pressure
suitably insulated. for this damper is 3000 Pa.

‘JFD’ Marine Fire and Gas Damper with actuator enclosure

2
 Construction · Materials · Standard Sizes

Type ‘JFD’ Marine Fire and Gas Dampers

Damper Casing Cross Link

2mm thick formed channel sections. 300mm 20 x 6mm flat sections located on linkage pins
wide (200mm option) with 50mm return flanges and retained by star lock washer.
on both faces and provided with lifting eyes. Case Material – Stainless steel 316
sections are fully welded externally at corner
joints. All welds on the damper face to be ground Linkage Cover
flush. Damper casing material thickness from 3 1mm top hat section to protect damper linkage
mm to 10mm can also be provided. Flanged and allow application of insulation (by others).
circular spigots for connection to circular ducts Material – Available in either galvanised steel
can be provided. or stainless steel to grade 304, 316 or 316L as
Material – Available in either galvanised steel or required.
stainless steel grade 304, 316 or 316L as
required. S ide seals
Roll formed from 75 x 0.3mm hardened and
Damper Blades ground stainless spring steel.
1.2mm thick-formed aerofoil sections, spot- Material – Stainless spring steel.
welded together to form a double skin insulated
blade. Blades have opposed action and the Blade Edge Seals (Provided as optional
linkage geometry allows the blades to interlock to extra if requested)
form an effective fire barrier. Retained in blade edge ‘V’ groove with fix wool
Material – Available in either galvanised steel or adhesive. Provides leakage rate in accordance
3 2
stainless steel to grade 304 316 or 316L as with UL555S Class 1 (less than 0.04m /s/m
required. damper face area at 1125 Pa).
Material – Kerlane ceramic fibre.
Bearings
20mm flanged oil impregnated sintered bronze Actuator mounting angles
bearings are pressed into the channel sections of 2.0mm thick formed angle sections welded to
the damper casing to support the blade shafts. damper casing with pre-drilled holes to suit
Material – Oil impregnated sintered bronze. actuator-mounting plate.
Material – Available in either galvanised steel
Shafts or stainless steel to grade 304, 316 or 316L as
20mm stub shafts at each end of the aerofoil required.
blades Shafts are bolted to the blade section with
M8 set of screws, nuts and washers. L anding angles
Material – Stainless steel 316 43mm x 7.5mm x 2mm angles bolted to the top
and bottom of the damper casing to provide
Drive Couplings blade stop and seal.
Pinned to shaft and comprising of two 20mm Material – Available in either galvanised steel
wide x 6mm thick flat steel sections welded to the or stainless steel to grade 304, 316 or 316L as
20mm drive shaft machined to suit the actuator. required.
Material – Stainless steel 316
Finish
Linkage This will be in natural finish of the material from
Pinned to shaft and comprising a 20mm wide x which the damper is made. For galvanised
6mm thick flat steel section with 8mm linkage sheet steel, all burrs will be removed and welds
pins. Geometry designed for accurate blade on the damper surface ground flushed and
phasing. finished with zinc rich paint.
Material – Stainless steel 316

3
General Details
Minimum and Maximum Damper Size

Standard Module Size (mm) 1 Damper casing 2 mm GMS or

Width (B) Height (H) stainless steel
Minimum size 200 200 2 Double skin (aerofoil) 1.2 mm GMS or
damper blade stainless steel
Maximum size 1050 1250 3 Stub shaft 20 mm Ø shaft
in stainless steel
4 Side seal Stainless steel
spring
The breadth (B) and height (H) are external duct 5 Tip seal Kerlane cord
dimensions.
6 Linkage assembly GMS or
stainless steel
7 Cross link bar GMS or
stainless steel
8 Actuator mounting GMS or
plates stainless steel
9 Linkage cover GMS or
stainless steel
10 Bearings Olite bronze

11 Insulation 60 kg/m
Rockwool
12 Landing angle GMS or
stainless steel

2
50 50

300

BOTH FLANGLES (50mm) PUNCHED

17 WITH “OBROUNDS” 14 mm WIDE
1 X 17mm O/AGENERALLY 150mm
“B” +(50mm X 2) PITCH, 31mm BACKMARK.

“B” MAX=1050/ “B” MIN=200 Ø14 LIFTING HOLES

31 9

8
4 @ 150

7
“H” MAX=1250/”H” MIN=200

6
“H” + (50mm x 2)

112

5
4 @ 150

3 @ 150 106 106 3 @ 150

4
 Product Range · Performance Data

In galvanised steel. Standard supply.

FL1 With side seals only.

Standard supply with

side and blade tip
FL2 seals to minimise
closed blade leakage.

Pressure drop across JFD Damper with blades in fully open position
80

70

60
Pressure drop (Pa)

50

40

30

20

10

0
1 Air Velocity (m/s) 10 20 30

5
Accessories

Table 1: Types of Actuator and limit switches

Fail
Mode of Type of construction variants and safe Product
operation mode of operation setting Coding
With With actuator only (Standard Supply) FC Z 10
pneumatic Complete with actuator and limit switch(es);
FO Z 11
spring return • Limit switch to indicate “Open” position.
actuator • Limit switch to indicate “Closed” position. FC Z 12
• Limits switches to indicate “Closed” and FO Z 13
“Open” positions. FC Z14
With electric With spring return actuator, operating at
spring return 230v; 50/60 Hz with IP 54 rating. Typical
actuator cycle time for motor is 150 s (or seconds)
and under spring force is 20 s unless stated
otherwise.
Note: Electric actuators for operation in
hazardous areas and with fast operating
times are available. Please contact TROX for
further details.
• Actuator without integral limit switches to
FC Z 20
indicate “Open” and closed position.
• Actuator with integral limit switches to FO Z 21
indicate “Open” and closed position. FC Z 22
• Actuator with an independent limit switch FO Z 23
to indicate “Open” position.
• Actuator with an independent limit switch
FC Z 24
to indicate “Closed” position.
• With independent limit switches to FO Z 25
indicate “Open” and “Closed” positions. FC Z 26

Table 2: Other ancillary Components

Item Type Description Product
Coding (A)
1 Thermal Trip Device Electro-thermal trip device rated at 72°C for 1
electric actuator
Electro-thermal trip device rated at 95°C for 2
electric actuator
3-port, 2 position SS 316 valve (as standard 3
supply), which is operated by a frangible bulb
rated at 68° and is suitable for pneumatic
actuators.
2 Quick Release Valve 4
for pneumatic actuators
only.
3 Junction Box 5
4 Earth Continuity Box 6
5 Solenoid Valve 7
6 Hand Valve 8
7 Pressure Regulator & 9
Gauge
8 L i m it S w i t c h e s V3 M echanical Switches (SPDT) 10
Herm Sealed Proxim ity Switch 11
P&F Switches (NJ2-V3) Eexia 12
9 Actuator/Controls 1.2mm thick material with removable cover 13
Enclosure

6
 Order Details

Note: If the order codes below are incomplete, then it is assumed that standard damper construction is required.

E1
E2
E3

© TROX Malaysia Sdn Bhd. (278360-V); 2010.

Subject to change without notice. ALL RIGHTS RESERVED

Breadth (mm) by Height (mm)

Make: TROX
G2 – 50 Flange (Standard Supply) Type: JFD– G-FL2-3-F4-0-0 / 600x600 /12 /R /V /Z01 /A1-5-6-8
Others - Special Quantity: 12 nos

The Type JFD is certified by the Lloyd s Register and ABS in accordance with the IMO Fire Test Procedures Code,
Annex1, Part 3, and it is suitable for both marine and offshore applications.