Scribd Logo
Upload

Welcome to Scribd!

  • 27 views

    Epomax-Anchor: Fast-Curing Anchoring Adhesive For Reinforcement Rods

    Uploaded by

    chaval01
    EPOMAX-ANCHOR is a two-component polyester-based anchoring adhesive that cures quickly. It does not contain solvents or styrene. EPOMAX-ANCHOR can be used to install reinforcement rods, threaded rods, and anchor bolts into concrete, solid rock, hollow and solid masonry. It provides design load values for concrete and recommended load values. Directions for use include drilling a hole, cleaning it, filling it completely with the adhesive, and allowing it to cure before applying loads.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Epomax-Anchor: Fast-Curing Anchoring Adhesive For Reinforcement Rods

    Uploaded by

    chaval01
    27 views2 pages
    EPOMAX-ANCHOR is a two-component polyester-based anchoring adhesive that cures quickly. It does not contain solvents or styrene. EPOMAX-ANCHOR can be used to install reinforcement rods, threaded rods, and anchor bolts into concrete, solid rock, hollow and solid masonry. It provides design load values for concrete and recommended load values. Directions for use include drilling a hole, cleaning it, filling it completely with the adhesive, and allowing it to cure before applying loads.

    Original Description:

    epo

    Original Title

    e-EPO

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    EPOMAX-ANCHOR is a two-component polyester-based anchoring adhesive that cures quickly. It does not contain solvents or styrene. EPOMAX-ANCHOR can be used to install reinforcement rods, threaded rods, and anchor bolts into concrete, solid rock, hollow and solid masonry. It provides design load values for concrete and recommended load values. Directions for use include drilling a hole, cleaning it, filling it completely with the adhesive, and allowing it to cure before applying loads.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    27 views2 pages

    Epomax-Anchor: Fast-Curing Anchoring Adhesive For Reinforcement Rods

    Uploaded by

    chaval01
    EPOMAX-ANCHOR is a two-component polyester-based anchoring adhesive that cures quickly. It does not contain solvents or styrene. EPOMAX-ANCHOR can be used to install reinforcement rods, threaded rods, and anchor bolts into concrete, solid rock, hollow and solid masonry. It provides design load values for concrete and recommended load values. Directions for use include drilling a hole, cleaning it, filling it completely with the adhesive, and allowing it to cure before applying loads.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Technical Datasheet

    EPOMAX-ANCHOR
    Fast-curing anchoring adhesive for reinforcement rods
    Description Thread diameter
    8 10 12 16 20
    d (mm)
    EPOMAX-ANCHOR is a two-component Drill diameter
    10 12 14 18 24
    polyester-based anchoring adhesive. It does d0 (mm)
    Anchorage depth
    not contain solvents and styrene and has no 80 90 110 125 170
    hef (mm)
    shrinkage behavior.
    Minimum
    partthickness 130 140 160 175 220
    Fields of application h min (mm)
    Edge distance
    EPOMAX-ANCHOR can be used as a fast- Ccr,N (mm) 80 90 110 130 170
    curing anchoring adhesive for reinforced bars, Axial distance
    threaded rods, anchor bolts, etc. It can be Scr,N (mm) 160 180 220 250 340
    used to install these fixtures into concrete,
    Design load
    solid rock, hollow and solid masonry, etc.
    values for
    12.3 18.4 26.0 30.2 48.1
    concrete C20/25
    Technical data NRk (KN)
    Recommended
    Base: polyester styrene free loads for
    4.7 7.1 10.0 11.2 18.8
    Color: grey concrete C20/25
    Frec (KN)
    Mixing
    proportion (A:B): 10:1 ratio by volume Directions for use
    Density: 1.65 kg/l
    Application 1. Installation to concrete or solid stone
    temperature: +5°C – 35°C Drill correct diameter hole to the
    recommended depth. Then clean the hole
    Curing: thoroughly with a nylon brush and remove any
    Temperature Working time Curing time loose particles using compressed air, hand
    + 5 OC 25 min 120 min pump, etc.
    + 10 OC 15 min 80 min Screw the mixer to the cartridge, after that,
    + 20 OC 6 min 45 min attach the mixer nozzle to the end of the
    + 30 OC 4 min 25 min cartridge and insert the cartridge into the
    + 35 OC 2 min 20 min applicator gun. Afterwards squeeze out to
    discard approximately 15 ml of compound,
    Compression strength: 75 Mpa after 24h this quantity is not used. Starting from the
    back end, fill hole completely with the resin.
    Push anchor up to base of hole whilst turning
    it slightly. A visual check of resin filling is
    necessary.
    Allow the material to cure before attaching
    fixings and applying loads. Be consulted the
    relative table of curing times for EPOMAX-
    ANCHOR.
    2. Installation to hollow bricks and artificial
    stone
    Drill hole without percussion drill. Then
    remove any loose particles using compressed
    air, hand pump, etc. Screw the mixer to the
    cartridge, after that, attach the mixer nozzle to
    the end of the cartridge and insert the
    cartridge into the applicator gun. Afterwards
    squeeze out to discard approximately 15 ml of
    compound, this quantity is not used.
    Insert the perforated sleeve in the hole.
    Starting from the back end, fill the perforated
    sleeve with resin. Afterwards, push anchor up
    to the base of the sleeve whilst turning it
    slightly. Allow the material to cure before
    attaching fixings and applying loads. Be
    consulted the relative table of curing times for
    EPOMAX-ANCHOR.

    Consumption

    Depending on the application.

    Packaging

    Cartridges of 300 ml.

    Shelf life – Storage

    Shelf life is 12 months, in dry and frost-free


    conditions.

    Remarks

    EPOMAX-ANCHOR can be applied in low


    ambient temperatures up to -5°C but the
    temperature of the product has to be at least
    10°C.

    ISOMAT S.A.
    BUILDING CHEMICALS AND MORTARS
    MAIN OFFICES - FACTORY:
    17th km Thessaloniki - Ag. Athanasios Road,
    P.O. BOX 1043, 570 03 Ag. Athanasios, Greece,
    Tel.: +30 2310 576 000, Fax: +30 2310 722 475
    www.isomat.eu e-mail: [email protected]

    The technical information and instructions supplied in this datasheet are based on the knowledge and experience of the Research
    and Development Department of our company and on results from long-term applications of the product in practice. The
    recommendations and suggestions referring to the use of the product are provided without guarantee, since site conditions during
    the applications are beyond the control of our company. Therefore the user is responsible for confirming that the chosen product is
    suitable for the envisaged application. The present edition of this technical datasheet automatically cancels any previous one
    concerning the same product.

    You might also like