Scribd Logo
Upload

Welcome to Scribd!

  • 143 views

    Masteremaco N 202: Description Priming

    Uploaded by

    shahid
    The document describes a cementitious mortar product called MasterEmaco N 202 that is used for cosmetic repairs and leveling of concrete surfaces. It can fill blowholes and defects up to 3mm thick. It has good workability and bonding to substrates and sets in 90 minutes. It is applied by brush, float or spray then finished smooth.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Masteremaco N 202: Description Priming

    Uploaded by

    shahid
    143 views2 pages
    The document describes a cementitious mortar product called MasterEmaco N 202 that is used for cosmetic repairs and leveling of concrete surfaces. It can fill blowholes and defects up to 3mm thick. It has good workability and bonding to substrates and sets in 90 minutes. It is applied by brush, float or spray then finished smooth.

    Original Description:

    Data Sheet R202

    Original Title

    R 202

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document describes a cementitious mortar product called MasterEmaco N 202 that is used for cosmetic repairs and leveling of concrete surfaces. It can fill blowholes and defects up to 3mm thick. It has good workability and bonding to substrates and sets in 90 minutes. It is applied by brush, float or spray then finished smooth.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    143 views2 pages

    Masteremaco N 202: Description Priming

    Uploaded by

    shahid
    The document describes a cementitious mortar product called MasterEmaco N 202 that is used for cosmetic repairs and leveling of concrete surfaces. It can fill blowholes and defects up to 3mm thick. It has good workability and bonding to substrates and sets in 90 minutes. It is applied by brush, float or spray then finished smooth.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    MasterEmaco® N 202

    A single component cementitious blowhole filler and levelling mortar for cosmetic repairs to new
    construction

    DESCRIPTION PRIMING
    MasterEmaco N 202 is a combination of The substrate should be thoroughly soaked, to a
    Portland cement, well graded sands and special saturated but surface dry condition prior to
    additives. application of the MasterEmaco N 202.
    When mixed with water MasterEmaco N 202
    produces a smooth cementitious paste ideally MIXING
    suited to filling of small surface defects and It is recommended that only full bags of 25 kg are
    blowholes thin layers of up to 3 mm maximum. mixed.
    MasterEmaco N 202 should be mixed by
    TYPICAL APPLICATIONS mechanical means with a slow speed drill and
    Surface leveling and blowhole filling for all spiral paddle.
    concrete elements such as The required amount of gauging water should be
     Beams, columns, and walls in high rise placed in the mixing bucket and the
    buildings MasterEmaco N 202 powder added and mixed
     Columns, Piers and cross beams on for approximately 3 minutes until a smooth,
    highway structures creamy and lump free consistency is achieved.
     Cooling towers and chimneys and other The water additions shall be a maximum of 6 L
    industrial structures per 25 kg bag.

    ADVANTAGES PLACING / APPLICATION


     Excellent workability for easy mixing, and Following mixing the MasterEmaco N 202 can
    fast application be applied by brush or the edge of a steel float
     Improved bond to substrate and scraped into substrate to fill all blowholes
     Compatible with MasterProtect protective and minor surface defects. A fine mist spray of
    coatings clean water should be applied to the finished
     Concrete coloured when cured surface. The hardened MasterEmaco N 202 can
    then be smoothed using sandpaper.
    Alternatively, MasterEmaco N 202 can be
    PACKAGING applied as a leveling mortar by steel float up to 3
    MasterEmaco N 202 is available in 25 kg bags. mm thick. The final finishing shall be by steel float
    or with a damp sponge depending upon the finish
    TYPICAL PROPERTIES* required. MasterEmaco N 202 can be
    overcoated 24 hours after application.
    Working time @ 25°C 60 min
    Setting time @ 25°C 90 min CURING
    Density ~1850 kg/m³ Generally curing is not necessary for cosmetic
    Compressive strength >15 N/mm² repair mortars however particular care is required
    @ 28 days ASTM C109-98
    in hot and/or windy conditions. Where a curing
    Pull off strength ASTM D4541 >1 N/mm²
    membrane is specified this can be using a curing
    membrane from the MasterKure range.
    APPLICATION GUIDELINES

    SURFACE PREPARATION
    All areas to be treated must be clean, sound and
    free from all dirt dust, loose material and any oil
    or grease which would impair adhesion.
    MasterEmaco® N 202

    COVERAGE / YIELD QUALITY AND CARE


    A 25 kg bag of MasterEmaco N 202 will yield All products originating from the Master Builders
    approximately 16.75 L of mortar. Solutions facility in Dubai are manufactured
    One bag of MasterEmaco N 202 will cover under a management system independently
    16.75 m² at thickness of 1 mm. This coverage is certified to conform to the requirements of the
    theoretical and depends upon the surface profile quality, environmental and occupational health
    of the substrate and the wastage. and safety standards ISO 9001, ISO 14001 and
    ISO 45001.
    WATCHPOINTS
    * Properties listed are based on laboratory controlled tests.
    During the summer months or where elevated
    ambient temperatures are encountered the ® = Registered trademark of the MBCC Group in many countries.
    MasterEmaco N 202 should be mixed using
    chilled water to ensure that the mixed
    temperature does not exceed 32°C.

    Do not add cement sand, or which may affect its


    properties.

    Do not add water or fresh mortar to material


    which has begun to set.

    STORAGE AND SHELF LIFE


    MasterEmaco N 202 should be stored in dry
    conditions out of direct sunlight.
    The shelf life is 12 months when stored as
    above.

    HEALTH AND SAFETY


    Avoid contact with eyes and prolonged contact
    with skin. In case of contact with eyes
    immediately flush for at least 15 minutes with
    fresh clean water. Call a physician.
    In case of contact with skin wash skin
    thoroughly.

    MBS_CC-UAE/Em_N202_10_06/v3/03_17/v4/09_19/v5/02_21
    The technical information and application advice given in this Master Builders Solutions publication are based on
    STATEMENT OF the present state of our best scientific and practical knowledge. As the information herein is of a general nature, no
    RESPONSIBILITY assumption can be made as to a product's suitability for a particular use or application and no warranty as to its
    accuracy, reliability or completeness either expressed or implied is given other than those required by law. The user
    is responsible for checking the suitability of products for their intended use.

    Field service where provided does not constitute supervisory responsibility. Suggestions made by Master Builders
    NOTE Solutions either orally or in writing may be followed, modified or rejected by the owner, engineer or contractor since
    they, and not Master Builders Solutions, are responsible for carrying out procedures appropriate to a specific
    application.

    Master Builders Solutions


    Construction Chemicals LLC
    P.O. Box 37127, Dubai, UAE
    Tel: +971 4 8090800
    www.master-builders-solutions.com/en-ae

    Disclaimer: the LRQA mark relates to


    certified management system and not to the
    product mentioned on this datasheet

    You might also like