9

TLE-EPAS
Electronic Products Assembly and Servicing
LEARNING ACTIVITY SHEET
(Quarter 1)
TLE 9 - IA (Electronic Products Assembly and Servicing)

TESTING ELECTRONIC COMPONENTS(TEC)

Division of Negros Occidental

GOVERNMENT PROPERTY
NOT FOR SALE
1
 dno_Q1Week1_EPAS10

Republic Act 8293, section 176 states that: No copyright shall subsist in any
work of the Government of the Philippines. However, prior approval of the government
agency or office wherein the work is created shall be necessary for exploitation of such
work for profit. Such agency or office may, among other things, impose as a condition
the payment of royalties.

This Learning Activity Sheet is developed by DepEd Division of Negros

Occidental

ALL RIGHTS RESERVED. No part of this learning resource may be reproduced

or transmitted in any form or by any means electronic or mechanical without written
permission from the DepEd Division of Negros Occidental.

Development Team of TLE 9 - IA (Electronic Products Assembly and

Servicing) Activity Sheet

Writer: JONATHAN T. TREYES

Cauayan National High School
Editors: BHEN V. VELASCO/ DAPHNE EMMA C. BELNAS
Layout Artists: JONATHAN T. TREYES
Schools Division Quality Assurance Team:
FIDEL B. DIOPITA
CELSA A. TABLESO
RHODELO C. TURBELA
FRANKLEEN L. DIVINAGRACIA
JUDY ANN B. NONATO
ELIZER B. PINEDA
SEVERINO O. ABELAY JR., EPS - EPP/TLE/TVL

Division of Negros Occidental Management Team:

OTHELO M. BEATING, PDO II, LRMDS
RAULITO D. DINAGA, EPS-LRMDS
SEVERINO O. ABELAY JR., EPS
Introductory Message! ZALDY H. RELIQUIAS, PhD, CID Chief
SALVACION J. SENAYO, CESE, ASDS
LYNEE A. PEÑAFLOR, ASDS
MARSETTE D. SABBALUCA, CESO VI,

2
Welcome to TLE 9 - IA (Electronic Products Assembly and Servicing)!

The Learning Activity Sheet is a product of the collaborative efforts of the

Schools Division of Negros Occidental and DepEd Regional Office VI - Western Visayas
through the Curriculum and Learning Management Division (CLMD). This is developed
to guide the learning facilitators (teachers, parents and responsible adults) in helping
the learners meet the standards set by the K to 12 Basic Education Curriculum.

The Learning Activity Sheet is self-directed instructional materials aimed to

guide the learners in accomplishing activities at their own pace and time using the
contextualized resources in the community. This will also assist the learners in acquiring
the lifelong learning skills, knowledge and attitudes for productivity and employment.

For learning facilitator:

The TLE 9 - IA (Electronic Products Assembly and Servicing) Activity Sheet

will help you facilitate the leaching-learning activities specified in each Most Essential
Learning Competency (MELC) with minimal or no face-to-face encounter between you
and learner. This will be made available to the learners with the references/links to ease
the independent learning.

For the learner:

The TLE 9 - IA (Electronic Products Assembly and Servicing) Activity Sheet

is developed to help you continue learning even if you are not in school. This learning
material provides you with meaningful and engaging activities for independent learning.
Being an active learner, carefully read and understand the instructions then perform the
activities and answer the assessments. This will be returned to your facilitator on the
agreed schedule.

3
 Quarter 1 – Week 3

LEARNING ACTIVITY SHEET (LAS) NO. 1

Name of Learner: ______________________________________________________

Grade and Section: _____________________ Date: ______________________

TLE 9 - IA (ELECTRONIC PRODUCTS ASSEMBLY AND SERVICING) ACTIVITY SHEET

TESTING ELECTRONICS COMPONENTS (Test Components- Resistor)

I. Learning Competency with Code

LO 3. Test components -Resistor

(TLE_IAEPAS912TEC-IIIh-i-25)
3.1 Apply testing methods to ensure that the products meet creative, production,
and
technical requirements.
3.2 Record problems and faults detected by testing and document remedial steps
taken in records system
3.3 Resolve problems and faults detected during testing in accordance with agreed
project or industry practice

CONTENT STANDARD:

The learners demonstrate an understanding of the underlying principles in testing

electronic components based on manufacturer’s specifications
and testing criteria.

PERFORMANCE STANDARD:

The learners shall be able to test electronic components based on manufacturer’s

Specification and testing criteria.

4
 II. Background Information for Learners

Directions/Instructions:
This module was designed and written with you in mind. It is here to help you master
the (Test Component – Resis1or). The scope of this module permits it to be used in many
different learning situations. The language used recognizes the diverse vocabulary level of
students. The lessons are arranged to follow the standard sequence of the course. But the order in
which you read them can be changed to correspond with the textbook you are now using.

This module consists of one lesson.

 LAS 1 – Application and Basic functions of Resistor

After going through this module, you are expected to:

1. Discuss the common applications Resistor
;
.2. Identify the basic troubles of Resistor

Read and answer the following activity on your answer sheet

1. Use the Learning Activity Sheet with care. Do not put unnecessary mark/s on any
part of the LAS. Use a separate sheet of paper in answering the exercises.
2. Don’t forget to answer activity 1 before moving on to the other activities included
in the LAS.
3. Read the instruction carefully before doing each activity.
4. Observe honesty and integrity in doing the tasks and checking your answers.
5. Finish the activity at hand before proceeding to the next.
6. Return this module to your teacher/facilitator once you are through with it.
Note: If you encounter any difficulty in answering the tasks in this module, do not hesitate to
consult your teacher or facilitator. Always bear in mind that you are not alone. You can
contact or message me in my Fb messenger.

Direction: Read the information of Resistor

A resistor is a passive two-terminal electrical component that implements electrical
resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow,
adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines,
among other uses. 

5
Ohm's law
Main article: Ohm's law
The behavior of an ideal resistor is dictated by the relationship specified by Ohm's law:

Ohm's law states that the voltage (V) across a resistor is proportional to the current (I), where
the constant of proportionality is the resistance (R). For example, if a 300 ohm resistor is
attached across the terminals of a 12 volt battery, then a current of 12 / 300 =
0.04 amperes flows through that resistor.
Practical resistors also have some inductance and capacitance which affect the relation between
voltage and current in alternating current circuits.
The ohm (symbol: Ω) is the SI unit of electrical resistance, named after Georg Simon Ohm. An
ohm is equivalent to a volt per ampere. Since resistors are specified and manufactured over a
very large range of values, the derived units of milliohm (1 mΩ = 10 −3 Ω), kilohm (1 kΩ = 103 Ω),
and megohm (1 MΩ = 106 Ω) are also in common usage.[2][3]:p.20

Series and parallel resistors

Main article: Series and parallel circuits
The total resistance of resistors connected in series is the sum of their individual resistance
values.

The total resistance of resistors connected in parallel is the reciprocal of the sum of the
reciprocals of the individual resistors.[3]:p.20ff

6
For example, a 10 ohm resistor connected in parallel with a 5 ohm resistor and
a 15 ohm resistor produces 1/1/10 + 1/5 + 1/15 ohms of resistance, or 30/11 =
2.727 ohms.
A resistor network that is a combination of parallel and series connections can
be broken up into smaller parts that are either one or the other. Some complex
networks of resistors cannot be resolved in this manner, requiring more
sophisticated circuit analysis. Generally, the Y-Δ transform, or matrix
methods can be used to solve such problems.[4][5][6]

Power dissipation
At any instant, the power P (watts) consumed by a resistor of

resistance R (ohms) is calculated as:   where V (volts) is the voltage across

the resistor and I (amps) is the current flowing through it. Using Ohm's law, the
two other forms can be derived. This power is converted into heat which must
be dissipated by the resistor's package before its temperature rises excessively.
[3]:p.22

Resistors are rated according to their maximum power dissipation. Discrete

resistors in solid-state electronic systems are typically rated as 1/10, 1/8, or 1/4
watt. They usually absorb much less than a watt of electrical power and require
little attention to their power rating.

An aluminum-encased power resistor rated for dissipation of 50 W when mounted on a

heat-sink
Resistors required to dissipate substantial amounts of power, particularly used
in power supplies, power conversion circuits, and power amplifiers, are
generally referred to as power resistors; this designation is loosely applied to
resistors with power ratings of 1 watt or greater. Power resistors are physically
larger and may not use the preferred values, color codes, and external
packages described below.
If the average power dissipated by a resistor is more than its power rating,
damage to the resistor may occur, permanently altering its resistance; this is
distinct from the reversible change in resistance due to its temperature
coefficient when it warms. Excessive power dissipation may raise the
temperature of the resistor to a point where it can burn the circuit board or
adjacent components, or even cause a fire. There are flameproof resistors that
fail (open circuit) before they overheat dangerously.
.

7
VZR power resistor 1.5kΩ 12W, manufactured in 1963 in the Soviet Union

Nonideal properties
Practical resistors have a series inductance and a small parallel capacitance;
these specifications can be important in high-frequency applications. In a low-
noise amplifier or pre-amp, the noise characteristics of a resistor may be an
issue.
The temperature coefficient of the resistance may also be of concern in some
precision applications.
Practical resistors are also specified as having a maximum power rating which
must exceed the anticipated power dissipation of that resistor in a particular
circuit: this is mainly of concern in power electronics applications. Resistors with
higher power ratings are physically larger and may require heat sinks. In a high-
voltage circuit, attention must sometimes be paid to the rated maximum working
voltage of the resistor. While there is no minimum working voltage for a given
resistor, failure to account for a resistor's maximum rating may cause the
resistor to incinerate when current is run through it.

Fixed resistors

A single in line (SIL) resistor package with 8 individual 47 ohm resistors. This package is
also known as a SIP-9. One end of each resistor is connected to a separate pin and the
other ends are all connected together to the remaining (common) pin – pin 1, at the end
identified by the white dot

8
Lead arrangements

Axial resistors with wire leads for through-hole mounting

Through-hole components typically have "leads" (pronounced /liːdz/) leaving the
body "axially," that is, on a line parallel with the part's longest axis. Others have
leads coming off their body "radially" instead. Other components may
be SMT (surface mount technology), while high power resistors may have one
of their leads designed into the heat sink.

Carbon composition

Old Style "Dog Bone" resistors with "body, tip, dot" color code marking.

Three carbon composition resistors in a 1960s valve (vacuum tube) radio

Carbon composition resistors (CCR) consist of a solid cylindrical resistive
element with embedded wire leads or metal end caps to which the lead wires
are attached. The body of the resistor is protected with paint or plastic. Early
20th-century carbon composition resistors had uninsulated bodies; the lead
wires were wrapped around the ends of the resistance element rod and
soldered. The completed resistor was painted for color-coding of its value.

Carbon pile
A carbon pile resistor is made of a stack of carbon disks compressed between

9
two metal contact plates. Adjusting the clamping pressure changes the
resistance between the plates. These resistors are used when an adjustable
load is required, for example in testing automotive batteries or radio
transmitters. A carbon pile resistor can also be used as a speed control for
small motors in household appliances (sewing machines, hand-held mixers)
with ratings up to a few hundred watts.[13] A carbon pile resistor can be
incorporated in automatic voltage regulators for generators, where the carbon
pile controls the field current to maintain relatively constant voltage. [14] The
principle is also applied in the carbon microphone.

Carbon film

Carbon film resistor with exposed carbon spiral (Tesla TR-212 1 kΩ)
A carbon film is deposited on an insulating substrate, and a helix is cut in it to
create a long, narrow resistive path. Varying shapes, coupled with
the resistivity of amorphous carbon (ranging from 500 to 800 μΩ m), can
provide a wide range of resistance values. Compared to carbon composition
they feature low noise, because of the precise distribution of the pure graphite
without binding.[15] Carbon film resistors feature a power rating range of 0.125 W
to 5 W at 70 °C. Resistances available range from 1 ohm to 10 megohm. The
carbon film resistor has an operating temperature range of −55 °C to 155 °C. It has
200 to 600 volts maximum working voltage range. Special carbon film resistors are
used in applications requiring high pulse stability.[12]

Printed carbon resistors

Carbon resistors (black rectangles) printed directly onto the SMD pads on a PCB. Inside
a 1989 vintage Psion II Organizer
Carbon composition resistors can be printed directly onto printed circuit
board (PCB) substrates as part of the PCB manufacturing process. Although
this technique is more common on hybrid PCB modules, it can also be used on
standard fiber glass PCBs. Tolerances are typically quite large, and can be in
the order of 30%. A typical application would be non-critical pull-up resistors.

10
Thick and thin film

Laser Trimmed Precision Thin Film Resistor Network from Fluke, used in the Keithley
DMM7510 multimeter. Ceramic backed with glass hermetic seal cover.
Thick film resistors became popular during the 1970s, and most SMD (surface
mount device) resistors today are of this type. The resistive element of thick
films is 1000 times thicker than thin films,[16] but the principal difference is how
the film is applied to the cylinder (axial resistors) or the surface (SMD resistors).
.
Thin film resistors are usually far more expensive than thick film resistors. For
example, SMD thin film resistors, with 0.5% tolerances, and with 25 ppm/K
temperature coefficients, when bought in full size reel quantities, are about
twice the cost of 1%, 250 ppm/K thick film resistors.

Metal film
A common type of axial-leaded resistor today is the metal-film resistor. Metal
Electrode Leadless Face (MELF) resistors often use the same technology.
Metal film resistors are usually coated with nickel chromium (NiCr), but might be
coated with any of the cermet materials listed above for thin film resistors.
Unlike thin film resistors, the material may be applied using different techniques
than sputtering (though this is one of the techniques). Also, unlike thin-film
resistors, the resistance value is determined by cutting a helix through the
coating rather than by etching. (This is similar to the way carbon resistors are
made.) The result is a reasonable tolerance (0.5%, 1%, or 2%) and a
temperature coefficient that is generally between 50 and 100 ppm/K. [18] 

Metal oxide film

Metal-oxide film resistors are made of metal oxides which results in a higher
operating temperature and greater stability and reliability than metal film. They
are used in applications with high endurance demands.

Wire wound

11
High-power wire wound resistors used for dynamic braking on an electric railway car.
Such resistors may dissipate many kilowatts for an extended length of time.

Types of windings in wire resistors:

1. common
2. bifilar
3. common on a thin former
4. Ayrton–Perry
Wire wound resistors are commonly made by winding a metal wire,
usually nichrome, around a ceramic, plastic, or fiberglass core. The ends of the
wire are soldered or welded to two caps or rings, attached to the ends of the
core. The assembly is protected with a layer of paint, molded plastic, or
an enamel coating baked at high temperature. These resistors are designed to
withstand unusually high temperatures of up to 450 °C.[12] Wire leads in low
power wire wound resistors are usually between 0.6 and 0.8 mm in diameter
and tinned for ease of soldering. For higher power wire wound resistors, either a
ceramic outer case or an aluminum outer case on top of an insulating layer is
used – if the outer case is ceramic, such resistors are sometimes described as
"cement" resistors, though they do not actually contain any traditional cement.
The aluminum-cased types are designed to be attached to a heat sink to
dissipate the heat; the rated power is dependent on being used with a suitable
heat sink, e.g., a 50 W power rated resistor overheats at a fraction of the power
dissipation if not used with a heat sink. Large wire wound resistors may be rated
for 1,000 watts or more.
Because wire wound resistors are coils they have more
undesirable inductance than other types of resistor, although winding the wire in
sections with alternately reversed direction can minimize inductance. Other
techniques employ bifilar winding, or a flat thin former (to reduce cross-section
area of the coil). For the most demanding circuits, resistors with Ayrton–Perry
winding are used.
Applications of wire wound resistors are similar to those of composition resistors
with the exception of the high frequency. The high frequency response of wire
wound resistors is substantially worse than that of a composition resistor. [12]

12
Foil resistor

Metal foil resistor

In 1960 Felix Zandman and Sidney J. Stein[19] presented a development of
resistor film of very high stability.
The primary resistance element of a foil resistor is a chromium nickel alloy foil
several micrometers thick. Chromium nickel alloys are characterized by having
a large electrical resistance (about 58 times that of copper), a small temperature
coefficient and high resistance to oxidation. Examples are Chromel A and
Nichrome V, whose typical composition is 80 Ni and 20 Cr, with a melting point
of 1420 °C. When iron is added, the chromium nickel alloy becomes more
ductile. The Nichrome and Chromel C are examples of an alloy containing iron.
The composition typical of Nichrome is 60 Ni, 12 Cr, 26 Fe, 2 Mn and Chromel
C, 64 Ni, 11 Cr, Fe 25. The melting temperature of these alloys are 1350° and
1390 °C, respectively.[20]
effects of the metal's electrical resistance increasing with temperature, and
being reduced by thermal expansion leading to an increase in thickness of the
foil, whose other dimensions are constrained by a ceramic substrate. [citation needed]

Ammeter shunts
An ammeter shunt is a special type of current-sensing resistor, having four
terminals and a value in milliohms or even micro-ohms. Current-measuring
instruments, by themselves, can usually accept only limited currents. To
measure high currents, the current passes through the shunt across which the
voltage drop is measured and interpreted as current. A typical shunt consists of
two solid metal blocks, sometimes brass, mounted on an insulating base.
Between the blocks, and soldered or brazed to them, are one or more strips of
low temperature coefficient of resistance (TCR) manganin alloy. Large bolts
threaded into the blocks make the current connections, while much smaller
screws provide volt meter connections. Shunts are rated by full-scale current,
and often have a voltage drop of 50 mV at rated current. Such meters are
adapted to the shunt full current rating by using an appropriately marked dial
13
face; no change need to be made to the other parts of the meter.

Grid resistor
In heavy-duty industrial high-current applications, a grid resistor is a large
convection-cooled lattice of stamped metal alloy strips connected in rows
between two electrodes. Such industrial grade resistors can be as large as a
refrigerator; some designs can handle over 500 amperes of current, with a
range of resistances extending lower than 0.04 ohms. They are used in
applications such as dynamic braking and load banking for locomotives and
trams, neutral grounding for industrial AC distribution, control loads for cranes
and heavy equipment, load testing of generators and harmonic filtering for
electric substations.[22]
The term grid resistor is sometimes used to describe a resistor of any type
connected to the control grid of a vacuum tube. This is not a resistor
technology; it is an electronic circuit topology.

Special varieties
● Cermet
● Phenolic
● Tantalum
● Water resistor

Variable resistors
Adjustable resistors
A resistor may have one or more fixed tapping points so that the resistance can
be changed by moving the connecting wires to different terminals. Some wire
wound power resistors have a tapping point that can slide along the resistance
element, allowing a larger or smaller part of the resistance to be used.
Where continuous adjustment of the resistance value during operation of
equipment is required, the sliding resistance tap can be connected to a knob
accessible to an operator. Such a device is called a rheostat and has two
terminals.

Potentiometers

Typical panel mount potentiometer

14
Drawing of potentiometer with case cut away, showing parts: (A) shaft, (B) stationary
carbon composition resistance element, (C) phosphor bronze wiper, (D) shaft attached
to wiper, (E, G) terminals connected to ends of resistance element, (F) terminal
connected to wiper.

An assortment of small through-hole potentiometers designed for mounting on printed

circuit boards.
A potentiometer (colloquially, pot) is a three-terminal resistor with a continuously
adjustable tapping point controlled by rotation of a shaft or knob or by a linear
slider.[23] The name potentiometer comes from its function as an
adjustable voltage divider to provide a variable potential at the terminal
connected to the tapping point. Volume control in an audio device is a common
application of a potentiometer. A typical low power potentiometer (see
drawing) is constructed of a flat resistance element (B) of carbon composition,
metal film, or conductive plastic, with a springy phosphor bronze wiper
contact (C) which moves along the surface. An alternate construction is
resistance wire wound on a form, with the wiper sliding axially along the coil.
[23]
 These have lower resolution, since as the wiper moves the resistance
changes in steps equal to the resistance of a single turn. [23]
High-resolution multiturn potentiometers are used in precision applications.
These have wire-wound resistance elements typically wound on a helical
mandrel, with the wiper moving on a helical track as the control is turned,
making continuous contact with the wire. Some include a conductive-plastic
resistance coating over the wire to improve resolution. These typically offer ten
turns of their shafts to cover their full range. They are usually set with dials that
include a simple turns counter and a graduated dial, and can typically achieve
three digit resolution. Electronic analog computers used them in quantity for

15
setting coefficients, and delayed-sweep oscilloscopes of recent decades
included one on their panels.

Resistance decade boxes

Main article: Decade box

Resistance decade box, made in former East Germany.

A resistance decade box or resistor substitution box is a unit containing
resistors of many values, with one or more mechanical switches which allow
any one of various discrete resistances offered by the box to be dialed in.
Usually the resistance is accurate to high precision, ranging from
laboratory/calibration grade accuracy of 20 parts per million, to field grade at
1%. Inexpensive boxes with lesser accuracy are also available. All types offer a
convenient way of selecting and quickly changing a resistance in laboratory,
experimental and development work without needing to attach resistors one by
one, or even stock each value. The range of resistance provided, the maximum
resolution, and the accuracy characterize the box. For example, one box offers
resistances from 0 to 100 megohms, maximum resolution 0.1 ohm, accuracy
0.1%.[24]

Special devices
There are various devices whose resistance changes with various quantities.
The resistance of NTC thermistors exhibit a strong negative temperature
coefficient, making them useful for measuring temperatures. Since their
resistance can be large until they are allowed to heat up due to the passage of
current, they are also commonly used to prevent excessive current surges when
equipment is powered on. Similarly, the resistance of a humistor varies with
humidity. One sort of photodetector, the photoresistor, has a resistance which
varies with illumination.

Measurement
The value of a resistor can be measured with an ohmmeter, which may be one
function of a multimeter. Usually, probes on the ends of test leads connect to
the resistor. A simple ohmmeter may apply a voltage from a battery across the
unknown resistor (with an internal resistor of a known value in series) producing
a current which drives a meter movement. The current, in accordance
with Ohm's law, is inversely proportional to the sum of the internal resistance
and the resistor being tested, resulting in an analog meter scale which is very
non-linear, calibrated from infinity to 0 ohms. A digital multimeter, using active
electronics, may instead pass a specified current through the test resistance.
16
 The voltage generated across the test resistance in that case is linearly
proportional to its resistance, which is measured and displayed. In either case
the low-resistance ranges of the meter pass much more current through the test
leads than do high-resistance ranges, in order for the voltages present to be at
reasonable levels (generally below 10 volts) but still measurable.

References

DepEd Curriculum Guide

https://en.wikipedia.org/wiki/Resistor
https://www.pinterest.ph/pin/639229740837237380/

https://www.physics-and-radio-electronics.com/electronic-devices-
andcircuits/passivecomponents/resistors/resistors.html#:~:text=Resistors%20are%20the%20most
%20 commonly,electric%20current%20to%20certain%20level.&text=Resistors%20are%2 0the
%20passive%20components,or%20electric%20current%20through%20them.

17
 III. Direction/instruction: Answer the following activities.

IV. Activities/Ex

Label the parts of a Multitester. Use the activity sheet for your answer.

1. _________
5._________

2. _________ _______
6.

_________
3. 7. _________

4. _________

18
Activity 2

Direction: complete the table by fill-in the blanks. Use the activity sheets for your answer.

Types of Resistor Definition Actual Pictures

a type of passive
component in which
1. ----------- metal wires are used to
reduce or restrict the
flow of electric current
to a certain level.

is a three-terminal
resistor in which the
resistance is manually
varied to control the
2. ------------- flow of electric current

a type of fixed resistor

that uses carbon film to
restrict the electric
3.-------------- current to certain level.
These types of resistors
are widely used in the
electronic circuits.

mostly wire wound.  

Hence, rheostats are
also sometimes referred
as variable wire wound
resistors. Generally,
rheostats are made by
winding the Nichrome
4.---------------
wire around an
insulating ceramic core.
The ceramic core of the
rheostat acts as the
19
 insulating material to
the heat. Hence, the
ceramic core does not
allow heat through it.

are just like a small

versions of a variable
resistor. They can be
placed easily on a PCB
5.--------------- and can also be
adjustable when
needed. The value of
the resistance is
normally adjusted with
the help of a screw-
driver

Activity 3
Identify the types of diagram and circuits and different kinds of circuit by
matching column A with column B. Write your answer on the blanks provided
below.

A. B.
________ 1. Trimmer a. is also sometimes referred as variable wire
wound resistors and made by winding the Nichrome
wire around the insulating ceramic core.

______ 2. Rheostat b. are just like a small version of a variable

They can be placed easily on a PCB and can
be adjustable when needed

________ 3. Carbon Film Resistor c. is a three-terminal resistor in which the

resistance is manually varied to control the flow of
electric current

________ 4. Wire Wound Resistor d. a type of fixed resistor that uses carbon film to
restrict the electric current to certain level. These
types of resistors are widely used in the electronic
circuits.
20
________ 5. Potentiometer e. a type of passive component in which metal
wires are used to reduce or restrict the flow of
electric current to a certain level

Activity 4

Identify the actual pictures used and its usage or functions of resistor in the
circuits.

Actual Pictures Usage or function

1.

3.

4.

21
 5.

Guide Questions

Read the questions below and write your answer on the space provided.

1. What is a resistor?
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________

2. What are the different types of resistors?

_____________________________________________________________
_____________________________________________________________
_____________________________________________________________

Reflection
Answer the question below and write your answer on the space provided.

Why we need to understand the different types of resistors and its usage and
functions?

_______________________________________________________________
_______________________________________________________________
_______________________________________________________________

22
VI. Rubric for Scoring

CATEGORY 4 3 2 1
All parts of the Most parts of the M Some parts of the Majority parts
drawing/video are drawing/video are drawing/video are of the
Clarity neat and focus in neat and focus in neat and focus in drawing/video
are not clear
20% the content easily the content easily the content easily
and net and are
viewed and viewed and viewed and too small.
identified. identified. identified.
All parts of the Most parts of the Some parts of the Majority parts
drawing/video are drawing/video are drawing/video are of the
Relevance related to the topic related to the topic related to the drawing/video
topic.
20% and make it easier and make it easier are not related
to understand to understand. to the topic.
All parts of the Most parts of the Some parts of the Majority parts
drawing/video are drawing/video are drawing/video are of the
clearly labeled drawing/video
23
Label clearly labeled clearly labeled with than can be were not
20% with than can be with than can be read/view. labeled
read/view. read/view. correctly and
are too small
to read/view.
The drawing/ The drawing/video Some of the Majority of the
video includes all includes all required elements required
Required required elements required elements. in drawing/video elements in
are included. drawing/video
Elements with additional
were missing.
20% information.
The drawing/video The drawing/videoT The drawing/video The
is exceptionally is attractive in is acceptably drawing/video
attractive in terms terms of design, attractive in terms is distractingly
messy or very
Attractiven of design, layout layout and of design, layout
poorly
ess and neatness. neatness. and neatness. designed it is
20% not attractive.
Submitted the Submitted the S Submitted the Submitted the
Timeliness drawing/video on drawing/video a drawing/video 2- drawing/video
10% or before the day after the 3 days after the more than 3
days after the
deadline. deadline. deadline.
deadline.

VII. Reflection
Answer the question below and write your answer on the space provided.

Why we need to understand the different types of resistors and its usage and
functions?

_______________________________________________________________
_______________________________________________________________
_______________________________________________________________

VIII. References

DepEd Curriculum Guide

https://en.wikipedia.org/wiki/Resistor
https://www.pinterest.ph/pin/639229740837237380/

24
 https://www.physics-and-radio-electronics.com/electronic-devices-
andcircuits/passivecomponents/resistors/resistors.html#:~:text=Resistors%20are%20the%20most
%20 commonly,electric%20current%20to%20certain%20level.&text=Resistors%20are%2 0the
%20passive%20components,or%20electric%20current%20through%20them.

IX. Answer Key

ACTIVITY 1 ACTIVITY 3
1. pointer 1.b
2. zero ohms adjusting nob 2.a
3.selector switch 3.d
4. com/negative 4.e
5. reading scale 5.c
6.pointer adjuster
7.ohmeter scale

25