LM107/LM207/LM307 Operational Amplifiers: General Description
LM107/LM207/LM307 Operational Amplifiers: General Description
LM107/LM207/LM307 Operational Amplifiers: General Description
December 1994
Connection Diagrams
Metal Can Package Dual-in-Line Package
TL/H/7757 – 2
Note: Pin 4 connected to case.
TL/H/7757 – 3
Top View
Top View
Order Number LM107H/883*
See NS Package Number H08C Order Number LM107J/883* or LM207J
See NS Package Number J08A
TL/H/7757 – 13
Order Number LM107J-14/883*
See NS Package Number J14A
2
Electrical Characteristics (Note 3) (Continued)
LM107/LM207 LM307
Parameter Conditions Units
Min Typ Max Min Typ Max
Large Signal Voltage VS e g 15V, VOUT e g 10V 15
Gain RL t 2 kX 25 V/mV
Output Voltage Swing VS e g 15V
RL e 10 kX g 12 g 14 g 12 g 14 V
RL e 2 kX g 10 g 13 g 10 g 13 V
Input Voltage Range VS e g 20V g 15 V
VS e g 15V a 15 g 12 a 15 V
b 13 b 13
Common Mode RS s 50 kX
80 96 70 90 dB
Rejection Ratio
Supply Voltage RS s 50 kX
80 96 70 96 dB
Rejection Ratio
Note 1: The maximum junction temperature of the LM107 is 150§ C, and the LM207/LM307 is 100§ C. For operating at elevated temperatures, devices in the H08
package must be derated based on a thermal resistance of 165§ C/W, junction to ambient, or 30§ C/W, junction to case. The thermal resistance of the dual-in-line
package is 100§ C/W, junction to ambient.
Note 2: For supply voltages less than g 15V, the absolute maximum input voltage is equal to the supply voltage.
Note 3: These specifications apply for g 5V s VS s a 20V and b 55§ C s TA s a 125§ C for the LM107 or b 25§ C s TA a 85§ C for the LM207, and 0§ C s TA s
a 70§ C and g 5V s VS s g 15V for the LM307 unless otherwise specified.
Note 4: Refer to RETS107X for LM107H and LM107J military specifications.
Schematic Diagram*
3
Guaranteed Performance Characteristics LM107/LM207
Input Voltage Range Output Swing Voltage Gain
TL/H/7757 – 4
TL/H/7757 – 5
TL/H/7757 – 6
4
Typical Performance Characteristics (Continued)
TL/H/7757 – 7
Typical Applications**
Inverting Amplifier Non-Inverting AC Amplifier
R2
VOUT e b VIN
R1 R1 a R2
VOUT e VIN
RIN e R1 R1
RIN e R3
TL/H/7757 – 8
R3 e R1//R2
TL/H/7757 – 9
Non-Inverting Amplifier
R1 a R2
VOUT e VIN
R1
TL/H/7757 – 10
5
Typical Applications** (Continued)
Turntable Notch Filter
R1 e R2 e R3
R1
R4 e R5 e
2
1
fo e
2q0C1 C2 R4 R5
e 60 Hz
TL/H/7757 – 11
TL/H/7757 – 12
**Pin connections shown are for metal can.
6
7
Physical Dimensions inches (millimeters)
8
Physical Dimensions inches (millimeters) (Continued)
9
LM107/LM207/LM307 Operational Amplifiers
Physical Dimensions inches (millimeters) (Continued)
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or 2. A critical component is any component of a life
systems which, (a) are intended for surgical implant support device or system whose failure to perform can
into the body, or (b) support or sustain life, and whose be reasonably expected to cause the failure of the life
failure to perform, when properly used in accordance support device or system, or to affect its safety or
with instructions for use provided in the labeling, can effectiveness.
be reasonably expected to result in a significant injury
to the user.
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.