Scribd
Upload
183 views2 pages

Reservoir Geomechanics: I. Compute The Overburden Stress and The Overburden Gradient

This document provides instructions for a homework assignment calculating overburden stress, porosity, and density from well log data from the Barnett Shale in Texas and the Gulf of Mexico. Students are asked to: 1) Plot density versus depth and block density into 5 depth units for both datasets 2) Calculate and plot overburden stress versus depth using blocked and continuous density and compare to hydrostatic pore pressure 3) Calculate overburden gradient versus depth for both datasets 4) Calculate porosity versus depth for both datasets using a matrix density of 2.7 g/cm3. Students are then asked to answer questions related to their calculations.

Uploaded by

Yaroslav Zaglyadin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
183 views2 pages

Reservoir Geomechanics: I. Compute The Overburden Stress and The Overburden Gradient

This document provides instructions for a homework assignment calculating overburden stress, porosity, and density from well log data from the Barnett Shale in Texas and the Gulf of Mexico. Students are asked to: 1) Plot density versus depth and block density into 5 depth units for both datasets 2) Calculate and plot overburden stress versus depth using blocked and continuous density and compare to hydrostatic pore pressure 3) Calculate overburden gradient versus depth for both datasets 4) Calculate porosity versus depth for both datasets using a matrix density of 2.7 g/cm3. Students are then asked to answer questions related to their calculations.

Uploaded by

Yaroslav Zaglyadin
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Reservoir Geomechanics

Homework No. 1 – Overburden Stress and Porosity


Due 8:00 am UTC Feburary 24th, 2020
If you want to see the current time in UTC, please google: current time in UTC

In this homework, you will be calculating the vertical stress (overburden stress) and porosity
using two different datasets, one from a well in the Barnett shale in Texas, and the other from a
well in the Gulf of Mexico (GOM).Both datasets will be used in future homework assignments.

Utilize Matlab (recommended) or Excel for calculation and answer the questions below. Both
datasets can be downloaded by clicking the right tab on the top of this page.

Use the following units in your calculation: ‘ft’ for depth, ‘g/cm3’ for density, ‘psi’ for overburden
stress and pore pressure, and ‘psi/ft’ for overburden stress gradient and pore pressure gradient.

I. Compute the overburden stress and the overburden gradient

1. Make a plot of density versus depth

• Barnett data – assume a reasonable surface density 1.8778 g/cm3 to extrapolate to the
first measurement point.

• GOM data – use a density of 1.0 g/cm3 from the surface to the sea floor (depth of 1000
ft) and a formation density of 1.7 g/cm3 at the sea floor. Linearly interpolate the density
between the sea floor and the depth at which the data starts (at the depth of 3515 ft).

2. “Block” the log into 5 depth units by assuming an approximately constant density over a
given range of depths. Compute and plot the averaged density in each block and your
blocked density as a function of depth for each dataset.

3. Calculate and plot the overburden stress as a function of depth using both the “blocked”
log and the continuous densities for each dataset. On the same plot, show hydrostatic
pore pressure 0.44 psi/ft versus depth as a reference. Use 9.8 m/s2 to approximate g, the
acceleration due to gravity.

4. Calculate the overburden gradient (overburden stress divided by the depth) for each data
set using the continuous density data. Plot the overburden gradient versus depth.

II. Compute porosity from the density measurements

Use the continuous density data and the formula rb = (1 - f) rmatrix + f rfluid to compute porosity
assuming full saturation of 1.0 g/cm3 water in the pores. Here f is the porosity. For rmatrix, assume
2.7 g/cm3, which is a reasonable value for a mixture of qtz, feldspar, mica and clay. Plot porosity
as a function of depth for each dataset.

III. Answer the questions on the page below

Use the calculations from I and II to answer the questions on the page below. The answers will
be posted a day after it is due. Numerical entry-type responses have a range of acceptable values
and are graded electronically, so please adhere to the value of constants given here. We will
specify the units that we want the answer in, so please do not write units in the answer, just write
the number.

You might also like