Kaiser Aluminum Sheet & Plate

FLAT ROLLED PRODUCTS
PLATE CAPABILITIES Availabilities in this document are subject to change without notice
AVAILABILITY FOR ALLOYS: 2024 2124 2219

Thickness (in.) Width (in.) Length (in.)
Maximum (per finished width)
Minimum Maximum Minimum Maximum Minimum
<=60.5” 60.6” - 74” >74”
0.250 0.270 24 62.0 90 216 216
0.271 0.500 24 62.0 90 350 350
0.501 0.749 24 66.0 90 358 358
0.750 1.500 24 84.5 90 358 358 358
1.501 2.000 24 84.5 90 358 358 358
2.001 3.000 24 84.5 90 344 344 206
3.001 4.000 24 60.5 90 334
Please inquire about thicknesses greater than 4.000”.
AVAILABILITY FOR ALLOY: 6061

<=60.5” 60.6” - 74” 74.1” - 86” 86.1” - 96.5”
0.250 0.270 24 62.0 90 221 221
0.271 0.500 24 66.0 90 350 350
0.501 0.749 24 66.0 90 365 365
0.750 1.500 24 84.5 90 365 365 365
1.501 1.999 24 84.5 90 365 365 365 365
2.000 2.999 24 84.5 90 351 351 329 329
3.000 4.000 24 84.5 90 348 348 233 233
4.001 4.500 24 84.5 90 348 348 193 193
4.501 5.000 24 84.5 90 342 325 171 171
5.001 5.500 24 84.5 90 342 286 145 145
5.501 6.000 24 74.0 90 342 253
6.001 6.500 24 74.0 90 342 225
6.501 7.000 24 74.0 90 342 208
7.001 7.500 24 74.0 90 317 188
7.501 7.750 24 74.0 90 303 178
7.751 8.000 24 74.0 90 290 169
8.001 8.500 24 74.0 90 267 153

<=50.0” 50.1” - 61” 61.1” - 74” 74.1” - 84.5”
0.250 0.270 24 62.0 90 216 216 216
0.271 0.500 24 62.0 90 350 350 350
0.501 0.749 24 66.0 90 368 368 368
0.750 1.500 24 84.5 90 358 358 358 358
1.501 2.000 24 84.5 90 358 358 358 351
2.001 3.150 24 84.5 90 344 344 341 166
www.kaiseraluminum.com | KA-SP-PC1-1.09
PLATE CAPABILITIES

<=60.5” 60.6” - 74” >74”
0.250 0.270 24 62.0 90 216 216
0.271 0.500 24 62.0 90 350 350
0.501 0.749 24 66.0 90 358 358
0.750 1.500 24 84.5 90 358 358 358
1.501 2.000 24 84.5 90 358 358 358
2.001 3.000 24 84.5 90 344 344 206
3.001 4.000 24 60.5 90 334

<=60.5” 60.6” - 74” >74”
0.25 0.270 24 62 90 216 216
0.271 0.500 24 62 90 350 350
0.501 0.749 24 66 90 358 358
0.750 1.500 24 84.5 90 358 358 358
1.501 2.000 24 84.5 90 358 358 358
2.001 2.999 24 84.5 90 344 344 206
3.000 3.937 24 60.5 90 334

<=60.5” 60.6” - 74” >74”
0.250 0.270 24 62.0 90 216 216
0.271 0.500 24 62.0 90 350 350
0.501 0.749 24 66.0 90 358 358
0.750 1.500 24 84.5 90 358 358 358
1.501 2.000 24 84.5 90 358 358 358
2.001 2.999 24 84.5 90 344 344 206
3.000 4.000 24 60.5 90 334
www.kaiseraluminum.com | KA-SP-PC2-1.09
SHEET & COIL CAPABILITIES
HEAT TREAT SHEET ALLOYS & TEMPERS

2014 2014A 2024 2219 6061 7075 7475
T4 T4 T3 T31 T4 W W
T6 T6 T4 (T-form) T37 T41 T6 T61
O-Temper T81 T81 T6 T73 T761
Special T351 T87 T76
Inquiry T361
T861
Notes
All alloys available in -O and -F tempers.

Available in Bare and Alclad.
O-temper “Hi-Form” available up through 0.130”.
6061 available as Bare only.
HEAT TREAT SHEET DIMENSIONAL CAPABILITIES

Width (in.) Length (in.)
Thickness (in.)
Coil Flat Sheet Flat Sheet
From Through Minimum Maximum Minimum Maximum Minimum Maximum
0.008 0.029 12 60 36 60 90 240
0.030 0.130 12 60 36 62 60 300
0.131 0.249 36 62 60 225
Notes
All T Temper coil is tension leveled through .071” thick.

Tempers T37, T87, T361 and T861 are available in flat sheet only 0.040” - 0.249”.
Alclad 2014 and 2219 special inquiry below 0.040”.
HOT ROLLED TREAD SHEET & PLATE

Width Length
Thickness
Minimum Maximum Minimum Maximum
Up to 0.250” 36.0 60.5 72.0 245.0
Over 0.250” 36.0 60.5 72.0 225.0
Notes
Gauges Available 0.125”, 0.156”, 0.188”, 0.250”, 0.375” and 0.500”.

Non-standard gauges subject to special availability.
Pattern B 6061-F, O, T4, T6 (ASTM B632).
www.kaiseraluminum.com | KA-SP-SCC-1.09
ORDER WEIGHTS
MINIMUM ORDER WEIGHTS FOR STANDARD SIZES (lbs.)

Coiled Sheet Flat Sheet Plate up to 2.999” Plate 3” and over
Alloy Width Width Width Thickness
<= 46.0” 46.01” - 49.00” 49.01” - 57.00” 57.01” - 63.00” <=46.0” 46.01” - 49.00” 49.01” - 57.00” 57.01” - 63.00” <=46.0” 46.01” - 49.00” 49.01” - 57.00” 57.01” - 66.00” 66.01” - 85.00” 3.00” - 4.99” 5.00” - 5.99” 6.00” - 6.99” 7.00” - 7.99” 8” and over
2014 / 2014A 3,000 3,500 3,250 2,500 3,250 3,500 3,750 2,500 3,250 3,250 3,250 3,000 5,500 5,500 5,500 5,500 5,500
2024 3,000 3,500 4,000 4,000 2,750 3,250 3,500 3,750 2,750 3,000 3,250 3,500 3,000 5,500 5,500 5,500 5,500 5,500
2124 2,500 3,000 3,000 3,000 3,000 5,500 5,500 5,500 5,500 5,500
2219 2,500 3,000 3,000 3,000 2,500 3,500 3,500 3,500 2,750 3,000 3,250 3,250 4,000 5,500 5,500 5,500 5,500 5,500
6061 3,750 4,500 4,500 4,500 3,500 4,250 4,250 5,000 4,500 5,000 5,000 5,000 5,000 10,000 8,000 8,000 9,000 10,000
7050 3,250 3,500 3,500 3,250 3,250 6,500 6,000 6,000 4,500 5,000
7075 3,250 3,250 3,250 4,000 2,750 3,250 3,250 3,750 3,000 3,000 3,250 3,500 3,250 6,000 6,000 6,000 5,000 5,000
7175 3,000 3,000 3,000 3,000 3,000 5,000 5,000 5,000 5,000 5,000
7475 2,500 3,500 3,500 3,500 2,500 3,000 3,000 3,250 2,750 3,000 3,000 3,000 3,000 5,000 5,000 5,000 5,000 5,000
6061 Tread Plate 3,750 4,500 4,500 5,000 3,750 4,500 4,500 5,000
MINIMUM ORDER WEIGHTS FOR NON-STANDARD SIZES (lbs.)

Coiled Sheet Flat Sheet Plate up to 2.999” Plate 3” and over
Alloy Width Width Width Thickness
<= 46.0” 46.01” - 49.00” 49.01” - 57.00” 57.01” - 63.00” <=46.0” 46.01” - 49.00” 49.01” - 57.00” 57.01” - 63.00” <=46.0” 46.01” - 49.00” 49.01” - 57.00” 57.01” - 66.00” 66.01” - 85.00” 3.00” - 4.99” 5.00” - 5.99” 6.00” - 6.99” 7.00” - 7.99” 8” and over
2014 / 2014A 6,000 7,000 6,500 5,000 6,500 7,000 7,500 5,000 6,500 6,500 6,500 6,000 5,500 5,500 5,500 5,500 5,500
2024 6,000 7,000 8,000 8,000 5,500 6,500 7,000 7,500 5,500 6,000 6,500 7,000 6,000 5,500 5,500 5,500 5,500 5,500
2124 5,000 6,000 6,000 6,000 6,000 5,500 5,500 5,500 5,500 5,500
2219 5,000 6,000 6,000 6,000 5,000 7,000 7,000 7,000 5,500 6,000 6,500 6,500 8,000 5,500 5,500 5,500 5,500 5,500
6061 7,500 9,000 9,000 9,000 7,000 8,500 8,500 10,000 9,000 10,000 10,000 10,000 10,000 10,000 8,000 8,000 9,000 10,000
7050 6,500 7,000 7,000 6,500 6,500 6,500 6,000 6,000 4,500 5,000
7075 6,500 6,500 6,500 8,000 5,500 6,500 6,500 7,500 6,000 6,000 6,500 7,000 6,500 6,000 6,000 6,000 5,000 5,000
7175 6,000 6,000 6,000 6,000 6,000 5,000 5,000 5,000 5,000 5,000
7475 5,000 7,000 7,000 7,000 5,000 6,000 6,000 6,500 5,500 6,000 6,000 6,000 6,000 5,000 5,000 5,000 5,000 5,000
6061 Tread Plate 7,500 9,000 9,000 10,000 7,500 9,000 9,000 10,000
www.kaiseraluminum.com | KA-SP-OW-1.09
AEROSPACE PLATE
SUMMARY OF SPECIFICATIONS
ALLOY TEMPER OWNER SPECIFICATION REV SPEC. MAX THICKNESS ALLOY TEMPER OWNER SPECIFICATION REV SPEC. MAX THICKNESS
SAE AMS 4028 G 1.000 F Otto Fuchs OFWN 4037 4 8.000
O
ASTM ASTM B 209 07 0.499 Airbus AIMS 03-02-022 6 7.874
SAE AMS 4029 K 4.000 SAE AMS 4050 H 8.000
2014 SAE AMS-QQ-A-250/3 4.000 Aerospatiale ASN-A3048 K 5.906
T651 ASTM ASTM B 209 07 4.000 Bombardier BAMS 516-003 NC 8.000
Boeing DMS 1580 A 3.000 Boeing BMS 7-323D TYPE I D 8.500
Boeing MMS 1112 6 3.000 Boeing BMS 7-323D TYPE III D 8.500
2014A T651 BSI BS L. 93 2 5.512 T7451 Cessna CMMP 025 R 8.000
SAE AMS 4035 K 1.750 Boeing DMS 2233 G 6.000
O SAE AMS-QQ-A-250/4 A 1.750 7050 Boeing DMS 2459 C 8.000
ASTM ASTM B 209 07 0.499 Eclipse EAC MS1004 E 8.000
Airbus ABM 1-1005 1 4.000 Eclipse EAC MS1005 E 8.000
French National AIR 9048-630 1 3.150 Lockheed LMA-M7050B C 8.000
SAE AMS 4037 N 4.000 Embraer MEP 02-014 L 8.500
SAE AMS-QQ-A-250/4 A 4.000 Boeing MMS 1420 G 6.000
2024 T351 Aerospatiale ASN-A3011 K 3.937 German Aero WL 3.4144 1 5.906
ASTM ASTM B 209 07 4.000 Airbus ABM 3-1029 5 4.724
Cessna CMMP 025 R 4.000 SAE AMS 4201 E 3.000
European EN 2419 P2 3.150 Bombardier BAMS 516-001 NC 3.000
T7651
BSI BS L. 97 2 5.512 Cessna CMMP 025 R 5.000
German Aerospace WL 3.1354 1 5.512 Boeing DMS 2233 G 3.000
SAE AMS-QQ-A-250/4 A 1.499 Eclipse EAC MS MP 0162 E 6.000
T851 ASTM ASTM B 209 07 1.499 SAE AMS 4044 K 2.000
Northrop Grumman GM2007 C 6.000 SAE AMS-QQ-A-250/12 2.000
O
SAE AMS 4101 C 6.000 ASTM ASTM B 209 07 2.000
SAE AMS-QQ-A-250/29 6.000 McDonnell Douglas STM0815-01 A 4.000
Eclipse EAC MS1002 F 6.000 SAE AMS 4045 J 4.000
2124 T851 Eclipse EAC MS1003 E 6.000 SAE AMS-QQ-A-250/12 4.000
T651
Lockheed FMS-3002 A 6.000 ASTM ASTM B 209 07 4.000
Lockheed FMS-3008 B 6.000 Cessna CMMP 025 R 3.000
Boeing MB0170-072 F 6.000 Aerospatiale AIR 9048-690 1 3.937
Boeing MMS 149 L 6.000 SAE AMS 4078 G 4.000
7075
SAE AMS 4031 G 2.000 SAE AMS-QQ-A-250/12 4.000
O SAE AMS-QQ-A-250/30 2.000 ASTM ASTM B 209 07 4.000
ASTM ASTM B 209 07 2.000 T7351 Cessna CMMP 025 R 5.000
SAE AMS-QQ-A-250/30 5.000 Eclipse EAC MS1011 E 4.000
T37
ASTM ASTM B 209 07 5.000 Boeing MMS 159 N 4.000
2219
SAE AMS 4295 B 6.000 Fokker TH 5.316/5 15 4.724
T851 SAE AMS-QQ-A-250/30 6.000 German Aero WL 3.4364 1 3.934
ASTM ASTM B 209 07 6.000 SAE AMS-QQ-A-250/24 A 2.000
SAE AMS-QQ-A-250/30 5.000 T7651 SAE AMS-QQ-A-250/25 A 1.000
T87
ASTM ASTM B 209 07 5.000 ASTM ASTM B 209 07 2.000
SAE AMS 4025 K 3.000 Airbus AIMS 03-02-008 4 3.937
7175 T7351
O SAE AMS-QQ-A-250/11 3.000 Aerospatiale ASN-A3050 L 3.937
ASTM ASTM B 209 07 3.000
This list is not necessarily up to date. Kaiser Aluminum may not be approved to produce every item listed.
SAE AMS 4026 L 3.000
SAE AMS-QQ-A-250/11 3.000
T451
ASME ASME SB 209 2004 3.000
ASTM ASTM B 209 07 3.000
6061 SAE AMS 4027 M 6.000
SAE AMS-QQ-A-250/11 6.000
ASME ASME SB 209 2004 6.000
ASTM ASTM B 209 07 6.000
T651 US Gov’t. MIL-DTL-46027 J 6.000
BAe Systems OAS-STD-9520 A 1.500
BAe Systems OAS-STD-9523 A 2.000 www.kaiseraluminum.com | KA-SP-APS1-1.09
AEROSPACE PLATE
ALLOY TEMPER OWNER SPECIFICATION REV SPEC. MAX THICKNESS

O Lockheed Martin 5PTM7T13 C 0.499
O1 Agusta 199-19-005 B 7.874
OP Boeing DMS 2184 L 1.500
SAE AMS 4202 D 4.000
Bombardier BAMS 516-002 NC 4.000
Cessna CMMP 025 R 4.000
Boeing DMS 2184 L 4.000
7475 Eclipse EAC MS1006 E 4.000
T7351 Lockheed FMS-3004 C 4.000
Embraer MEP 02-013 - std P 4.000
Embraer MEP 02-013 - Type I P 4.000
Embraer MEP 02-013 - Type II P 4.000
Embraer MEP 02-013 - Type III P 4.000
German Aero WL 3.4384 1 3.937
SAE AMS 4089 D 1.500
T7651
Boeing DMS 2184 L 1.500
SAE AMS STD 2154 CL A All
Boeing (All) BSS 7055 CL A A All
Northrop Grumman GSS 16100 G All
ASTM ASTM B594 CL A 6 All
USI
Boeing BAC5439 H All
Boeing PS21211 K All
Cessna CST1006 C All
McDonnell Douglas DPS4713 AH All
www.kaiseraluminum.com | KA-SP-APS2-1.09
AEROSPACE PLATE
SPECIFICATIONS BY ALLOY
ALLOY TEMPER SPECIFICATION ALLOY TEMPER SPECIFICATION

AMS4028 AMS4025
O
ASTMB209 AMS4027
AMS4029 O AMSQA25011
2014 AMSQA2503 ASMESB209
T651 ASTMB209 ASTMB209
DMS1580 AMS4026
MMS1112 AMSQA25011
T4
EN2395 ASMESB209
T4
2014A L156 ASTMB209
T651 L93 AMS4026
AMS4035 6061 AMSQA25011
T451
AMS4040 ASMESB209
O AMSQA2504 ASTMB209
AMSQA2505 T6 ASTMB632
ASTMB209 AMS4027
AMS4041 AMS4078
T3 AMSQA2505 AMSQA25011
T651
ASTMB209 ASMESB209
ABM11005 ASTMB209
AIR9048630 EN10204
AMS4037 F OFWN4037
AMS4041 AIMS302000
2024 AMSQA2504 AIMS302022
AMSQA2505 AMS4050
T351 ASNA3011 ASNA3048
ASTMB209 BAMS516003
CMMP025 BMS7323TY1
DAN422 BMS7323TY3
EN2419 T7451 CMMP025
L97 DAN422
WL31354 DMS2233
WL31364 7050 DMS2459
AMSQA2504 EACMS1004
T851 ASTMB209 EACMS1005
GM2007 LMAM7050
AMSQA25029 MEP02014
F
MMS149 MMS1420
AMS4101 WL34144
AMSQA25029 ABM31029
EACMS1002 AMS4201
2124
T851 EACMS1003 BAMS516001
T7651
FMS3002 CMMP025
FMS3008 DMS2233
MB0170072 EACMSMP162
MMS149
AMS4031
O AMSQA25030
ASTMB209
AMSQA25030
2219 T37
ASTMB209
AMS4295
T851 AMSQA25030
ASTMB209
AMSQA25030
T87
ASTMB209
www.kaiseraluminum.com | KA-SP-APSBA1-1.09
AEROSPACE PLATE
SPECIFICATIONS BY ALLOY
ALLOY TEMPER SPECIFICATION

AMS4044
AMS4048
AMSQA25012
O AMSQA25013
ASTMB209
STM081501
AMS4045
AMS4048
AMS4049
AMS4078
T651
AMSQA25012
AMSQA25013
ASTMB209
CMMP025
7075 MMS159
AIR9048690
AMS4078
AMSQA25012
ASTMB209
CMMP025
T7351
DAN422
EACMS1011
EN10204
MMS159
TH53165
WL34364
AMSQA25024
T7651 AMSQA25025
ASTMB209
AIMS302000
AIMS302008
7175 T7351 ASNA3050
EN10204
IGC0432105
O 5PTM7T13
O1 19919005
OP DMS2184
AMS4202
BAMS516002
CMMP025
T7351 DAN422
7475
DIN29546
DMS2184
EACMS1006
FMS3004
MEP02013
WL34384
AMS4089
T7651
DMS2184
www.kaiseraluminum.com | KA-SP-APSBA2-1.09
AEROSPACE FLAT SHEET
ALLOY TEMPER OWNER SPECIFICATION REV DESCRIPTION ALLOY TEMPER OWNER SPECIFICATION REV DESCRIPTION
O SAE AMS-QQ-A-250/3 Alclad 2014 Sheet & Plate British Aerospace BAEM 1010 2 Alclad 2024-T42 (O,F) Sheet
ASTM ASTM B 209 07 All Sheet & Plate Alloys BSI BS L 110 1 Alclad 2024-F Sheet
SAE AMS-QQ-A-250/3 Alclad 2014 Sheet & Plate F Dassault CR 1.1.0.55 C Bare & Alclad Sheet
ASTM ASTM B 209 07 All Sheet & Plate Alloys German Aerospace DAN 424 1288 German Sheet Requirements
2014 T3 Boeing D6-83818 Boeing Polished Skin Standards Hawker Siddeley S07-1010 1 Alclad 2024-F & O Temper Sheet
Boeing DMS 2130 A Premium Polished Skin Quality German Aerospace WL 3.1364 1 Alclad 2024 Sheet & Plate
Boeing DMS 2174 B MRS Requirements Airbus ABM 1-6015 2 Bare 2024-T3 Sheet
SAE AMS 4029 K Bare 2014-T6 Sheet & T651 Plate Airbus ABM 1-7068 1 Alclad 2024-T42 Close Tol.Sheet
T6 SAE AMS-QQ-A-250/3 Alclad 2014 Sheet & Plate Airbus AIMS 03-04-000 3 Alum. Sheet & Plate to 12 mm.
ASTM ASTM B 209 07 All Sheet & Plate Alloys Airbus AIMS 03-04-010 5 Alclad 2024-T42 Sheet
Boeing BAC M 196 A Alclad 2014A-F Sheet French Standards AIR 9048-100 1 Bare 2024-O Sheet
BSI BS L 156 Bare 2014A-T4 Sheet French Standards AIR 9048-130 1 Alclad 2024-O Sheet
BSI BS L 158 Bare 2014A-T4 Close Tol. Sheet SAE AMS 4035 K Bare 2024-O Sheet & Plate
F BSI BS L 164 Alclad 2014A-T4 Sheet SAE AMS 4040 M Alclad 2024-O Sheet & Plate
BSI BS L166 Alclad 2014A-T4 Close Tol. Sheet SAE AMS 4274 A Alclad 2024-O Hi-Form Sheet
British Standards EN 2088 2005 Alclad 2014A-T4 Sheet SAE AMS 4276 A Bare 2024-O Hi-Form Sheet
British Standards EN 2089 2005 Bare 2014A-T6/T62 Sheet SAE AMS-QQ-A-250/4 A Bare 2024 Sheet & Plate
British Standards EN 2395 2005 Bare 2014A-T4 Sheet SAE AMS-QQ-A-250/5 A Alclad 2024 Sheet & Plate
T3 BSI BS L 163 Alclad 2014A-T3 Sheet Aerospatiale ASN-A3042 E Alclad 2024-T42 Sheet
Airbus ABM 1-6013 1 Bare 2014A-T4 Close Tol. Sheet ASTM ASTM B 209 07 All Sheet & Plate Alloys
Airbus ABM 1-7018 1 Alclad 2014A-T4 Close Tol.Sheet British Aerospace BAEM 1010 2 Alclad 2024-T42 (O,F) Sheet
French Standards AIR 9048-020 1 Bare 2014A-T4 Sheet British Aerospace BAEM 4075 1 Alclad 2024-T4 Sheet
BSI BS L 156 Bare 2014A-T4 Sheet Bombardier BAMS 516-010 NC Bare & Alclad 2024-O Hi-Form
2014A BSI BS L 158 Bare 2014A-T4 Close Tol. Sheet Boeing BMS 7-305 A Alclad 2024-O Hi-Form Sheet
BSI BS L 164 Alclad 2014A-T4 Sheet O BSI BS L 109 1 Alclad 2024-T3 Sheet
BSI BS L166 Alclad 2014A-T4 Close Tol. Sheet BSI BS L 110 1 Alclad 2024-F Sheet
British Standards EN 10204-3.1 2004 Test Report Specification Cessna CMMP 021 A Hi-Form O-Temper Sheet
T4 British Standards EN 2087 2005 Alclad 2014A-T6 Sheet Cessna CMMP 025 R Metal Procurement Requirements
British Standards EN 2088 2005 Alclad 2014A-T4 Sheet 2024 Dassault CR 1.1.0.55 C Bare & Alclad Sheet
British Standards EN 2089 2005 Bare 2014A-T6/T62 Sheet Boeing D6-83818 Boeing Polished Skin Standards
British Standards EN 2395 2005 Bare 2014A-T4 Sheet German Aerospace DAN 34 0189 Specification for Chem. Milling
British Aerospace MM 0551 1 Alclad 2014A-T4/T42 Close Tol. German Aerospace DAN 424 1288 German Sheet Requirements
British Aerospace MM 0552 3 Alclad 2014A-T6/T62 Close Tol. German Standards DIN 29 546 13 German Aluminum Specification
British Aerospace MM 0553 2 Alclad 2014A-T4/T42 Close Tol. Boeing DMS 1949 D Premium Skin Quality
British Aerospace MM 0554 1 Alclad 2014A-T6/T62 Close Tol. Boeing DMS 2130 A Premium Polished Skin Quality
Hawker Siddeley S07-1007 1 Alclad 2014A-T4 Sheet Boeing DMS 2411 Hi-Form 6061, 2XXX & 7XXX
Hawker Siddeley S07-1020 1 Bare 2014A-T4 Sheet British Standards EN 10204-3.1 2004 Test Report Specification
Airbus ABM 1-6014 1 Bare 2014A-T6 Close Tol. Sheet Embraer MEP 02-015 B Embraer Alclad 2024-O Hi-Form
Airbus ABM 1-7019 1 Alclad 2014A-T6 Close Tol.Sheet Rohr RMS 171 Bare 2024- Hi-Form Sheet
BSI BS L 157 Bare 2014A-T6 Sheet Hawker Siddeley S07-1010 1 Alclad 2024-F & O Temper Sheet
BSI BS L 159 Bare 2014A-T6 Close Tol. Sheet Fokker TH 5.322 21 Alclad 2024 Sheet
BSI BS L 165 Alclad 2014A-T6 Sheet German Aerospace WL 3.1354 1 Bare 2024 Sheet & Plate
BSI BS L 167 Alclad 2014A-T6 Close Tol. Sheet German Aerospace WL 3.1364 1 Alclad 2024 Sheet & Plate
T6 British Standards EN 10204-3.1 2004 Test Report Specification Bell 299-947-040 N 2024-T3 Sheet for Rotor Blades
British Standards EN 2087 2005 Alclad 2014A-T6 Sheet Bell 299-947-157 E MRS for Bell Helicopter
British Standards EN 2089 2005 Bare 2014A-T6/T62 Sheet Airbus ABM 1-6015 2 Bare 2024-T3 Sheet
British Aerospace MM 0552 3 Alclad 2014A-T6/T62 Close Tol. Airbus ABM 1-7067 1 Alclad 2024-T3 Close Tol. Sheet
British Aerospace MM 0554 1 Alclad 2014A-T6/T62 Close Tol. Airbus AIMS 03-04-000 3 Alum. Sheet & Plate to 12 mm.
Hawker Siddeley S07-1008 1 Alclad 2014A-T6 Sheet Airbus AIMS 03-04-009 2 Alclad 2024-T351 Sheet
Hawker Siddeley S07-1021 1 Bare 2014A-T6 Sheet Airbus AIMS 03-04-014 2 Alclad 2024-T3 Sheet
Airbus ABM 1-7068 1 Alclad 2024-T42 Close Tol. Sheet T3 French Standards AIR 9048-110 1 Bare 2024-T3 Sheet
Airbus AIMS 03-04-000 3 Alum. Sheet & Plate to 12 mm. French Standards AIR 9048-140 1 Alclad 2024-T3 Sheet
Airbus AIMS 03-04-010 5 Alclad 2024-T42 Sheet SAE AMS 4037 N Bare 2024-T3/T351 Sheet & Plate
2024 F French Standards AIR 9048-130 1 Alclad 2024-O Sheet SAE AMS 4041 Q Alclad 2024-T3/T351 Sheet & Plate
SAE AMS 4040 M Alclad 2024-O Sheet & Plate SAE AMS 4101 C Bare 2124-T851 Plate
SAE AMS-QQ-A-250/5 A Alclad 2024 Sheet & Plate SAE AMS-QQ-A-250/4 A Bare 2024 Sheet & Plate
Aerospatiale ASN-A3042 E Alclad 2024-T42 Sheet SAE AMS-QQ-A-250/5 A Alclad 2024 Sheet & Plate
www.kaiseraluminum.com
| KA-SP-AFSS1-1.09
Aerospatiale ASN-A3010 H Bare 2023-T3 Sheet T4 Eclipse E410-MS-0006 A Eclipse Bare 2024-T4 (T-Form)
Aerospatiale ASN-A3012 M Alclad 2024-T3 Sheet SAE AMS-QQ-A-250/4 A Bare 2024 Sheet & Plate
ASTM ASTM B 209 07 All Sheet & Plate Alloys SAE AMS-QQ-A-250/5 A Alclad 2024 Sheet & Plate
British Aerospace BAEM 1009 2 Alclad 2024-T3 Sheet 2024 ASTM ASTM B 209 07 All Sheet & Plate Alloys
British Aerospace BAEM 4006 1 Alclad 2024-T3 Sheet T81 Boeing D6-83818 Boeing Polished Skin Standards
Bombardier BATS 2505 NC MRS Testing Specification Boeing DMS 2130 A Premium Polished Skin Quality
BSI BS 25359 3 Raytheon MRS Sheet Boeing DMS 2174 B MRS Requirements
BSI BS L 109 1 Alclad 2024-T3 Sheet Rohr RMS 145 C Rohr Chemical Milling (MRS)
Cessna CCM-41 C Alclad 2024-T3 Sheet SAE AMS 4031 G Bare 2219-0 Sheet & Plate
Cessna CMMP 025 R Metal Procurement Requirements SAE AMS 4096 B Alclad 2219-O Sheet & Plate
Dassault CR 1.1.0.55 C Bare & Alclad Sheet SAE AMS 4295 B Bare 2219 Sheet & Plate
Dassault CR 1.1.0.8 J Alclad 2024-F, H111, T3 Sheet SAE AMS-QQ-A-250/30 Bare 2219 Sheet & Plate
Boeing D6-83818 Polished Skin Standards ASTM ASTM B 209 07 All Sheet & Plate Alloys
T3 German Aerospace DAN 424 1288 German Sheet Requirements Boeing BMS 7-110 F Alclad 2219 Sheet & Plate
German Standards DIN 29 546 13 German Aluminum Specification O Dassault CR 1.1.0.39 E Chemical Milling Requirements
Boeing DMS 1949 D Premium Skin Quality Dassault CR 1.1.0.55 C Bare & Alclad Sheet
Boeing DMS 2130 A Premium Polished Skin Quality Dassault CR 1.1.0.82 Alclad 2219-O Sheet
Boeing DMS 2174 B MRS Requirements Dassault CR1.1.081 Bare 2219 Sheet
Eclipse EAC MS1013 A Bare 2024-T3 Stretched Sheet Boeing D6-83818 Boeing Polished Skin Standards
British Standards EN 10204-3.1 2004 Test Report Specification Boeing DMS 1719 D Alclad 2219 Sheet & Plate
British Standards EN 2090 2005 Alclad 2024-T3 Sheet Rohr RMS 162 Bare 2219-O Hi-Form Sheet
Lockheed FMS-3022 A MRS Sheet Airbus AIMS 03-04-000 3 Alum. Sheet & Plate to 12 mm.
Embraer MEP 02-015 B Embraer Alclad 2024-O Hi-Form Airbus AIMS 03-04-041 1 Bare 2219-T31/T81 Sheet
Rohr RMS 145 C Rohr Chemical Milling (MRS) SAE AMS 4095 C Alclad 2219-T3/T351 Sheet & Plate
Hawker Siddeley S07-1009 1 Alclad 2024 Close Tol. Sheet 2219 SAE AMS-QQ-A-250/30 Bare 2219 Sheet & Plate
Hawker Siddeley S07-1029 2 Bare 2024-T3 Sheet ASTM ASTM B 209 07 All Sheet & Plate Alloys
Fokker TH 5.312 22 2024 Sheet & Plate T31 Boeing BMS 7-110 F Alclad 2219 Sheet & Plate
Fokker TH 5.322 21 Alclad 2024 Sheet Boeing DMS 1719 D Alclad 2219 Sheet & Plate
2024 German Aerospace WL 3.1354 1 Bare 2024 Sheet & Plate Boeing DMS 2174 B MRS Requirements
German Aerospace WL 3.1364 1 Alclad 2024 Sheet & Plate Rohr RMS 145 C Rohr Chemical Milling (MRS)
Airbus AIMS 03-04-000 3 Alum. Sheet & Plate to 12 mm. Lockheed STM07-101 E Alclad 2219 Sheet
Airbus AIMS 03-04-009 2 Alclad 2024-T351 Sheet SAE AMS 4094 C Alclad 2219-T81/T851 Sheet & Plate
French Standards AIR 9048-120 1 Bare 2024-T351 Sheet SAE AMS-QQ-A-250/30 Bare 2219 Sheet & Plate
French Standards AIR 9048-140 1 Alclad 2024-T3 Sheet ASTM ASTM B 209 07 All Sheet & Plate Alloys
SAE AMS 4041 Q Alclad 2024-T3/T351 Sheet & Plate T81 Boeing BMS 7-110 F Alclad 2219 Sheet & Plate
SAE AMS-QQ-A-250/5 A Alclad 2024 Sheet & Plate Boeing DMS 1719 D Alclad 2219 Sheet & Plate
Aerospatiale ASN-A3012 M Alclad 2024-T3 Sheet Boeing DMS 2174 B MRS Requirements
British Aerospace BAEM 1009 2 Alclad 2024-T3 Sheet Rohr RMS 145 C Rohr Chemical Milling (MRS)
T351 BSI BS L 109 1 Alclad 2024-T3 Sheet Lockheed STM07-101 E Alclad 2219 Sheet
German Aerospace DAN 34 0189 Specification for Chem. Milling SAE AMS-QQ-A-250/30 Bare 2219 Sheet & Plate
T87
German Aerospace DAN 424 1288 German Sheet Requirements ASTM ASTM B 209 07 All Sheet & Plate Alloys
German Standards DIN 29 546 13 German Aluminum Specification H111 Aerospatiale ASN-A3001 D Bare 6061-T42 Sheet (O & H111)
British Standards EN 10204-3.1 2004 Test Report Specification Airbus AIMS 03-04-000 3 Alum. Sheet & Plate to 12 mm.
Hawker Siddeley S07-1009 1 Alclad 2024 Close Tol. Sheet Airbus AIMS 03-04-042 2 Bare 6061-T62 Sheet
German Aerospace WL 3.1354 1 Bare 2024 Sheet & Plate SAE AMS 4025 L Bare 6061-O Sheet & Plate
German Aerospace WL 3.1364 1 Alclad 2024 Sheet & Plate SAE AMS-QQ-A-250/11 A Bare 6061 Sheet & Plate
Airbus AIMS 03-04-000 3 Alum. Sheet & Plate to 12 mm. Aerospatiale ASN-A3001 D Bare 6061-T42 Sheet (O & H111)
Airbus AIMS 03-04-024 2 Alclad 2024-T4 (T-Form) Sheet O ASTM ASTM B 209 07 All Sheet & Plate Alloys
Airbus AIMS 03-04-044 2 Alclad 2024-T4 (T62) Sheet 6061 Boeing BMS 7-312 Bare 6061-O Hi-Form Sheet
SAE AMS 4279 B Alclad 2024-T4 (T-Form) Sheet Cessna CMMP 021 A High Form O-Temper Sheet
SAE AMS 4297 A Bare 2024-T4 (T-Form) Sheet Cessna CMMP 025 R Metal Procurement Requirements
T4 SAE AMS-QQ-A-250/4 A Bare 2024 Sheet & Plate German Aerospace DAN 424 1288 German Sheet Requirements
SAE AMS-QQ-A-250/5 A Alclad 2024 Sheet & Plate Boeing DMS 2411 Hi-Form 6061, 2XXX & 7XXX
ASTM ASTM B 209 07 All Sheet & Plate Alloys German Aerospace WL 3.3214 1 6061 Sheet & Plate
Boeing BMS 7-363 Bare & Alclad 2024-T4 (T-Form) SAE AMS 4025 L Bare 6061-O Sheet & Plate
Cessna CMMP 020 Bare & Alclad 2024-T4 (T-Form) O1 SAE AMS-QQ-A-250/11 A Bare 6061 Sheet & Plate
Cessna CMMP 025 R Metal Procurement Requirements ASTM ASTM B 209 07 All Sheet & Plate Alloys
www.kaiseraluminum.com
| KA-SP-AFSS2-1.09
Airbus ABM 2-6027 2 6061-T4 Sheet SAE AMS 4049 K Alclad 7075-T6/T651 Sheet & Plate
Airbus AIMS 03-04-000 3 Alum. Sheet & Plate to 12 mm. SAE AMS-QQ-A-250/12 Bare 7075 Sheet & Plate
Airbus AIMS 03-04-042 2 Bare 6061-T62 Sheet SAE AMS-QQ-A-250/13 Alclad 7075 Sheet & Plate
French Standards AIR 9048-220 1 Bare 6061-T4 Sheet Aerospatiale ASN-A3051 D Alclad 7075-T6 Sheet
SAE AMS 4026 M Bare 6061-T4/T451 Sheet & Plate ASTM ASTM B 209 07 All Sheet & Plate Alloys
SAE AMS-QQ-A-250/11 A Bare 6061 Sheet & Plate Bombardier BATS 2505 NC MRS Testing Specification
ASME ASME SB 209 2004 Boiler Plate Spec. (6061) Cessna CMMP 025 R Metal Procurement Requirements
Aerospatiale ASN-A3046 D Bare 6061-T4 Sheet T6 Boeing D6-83818 Boeing Polished Skin Standards
T4 ASTM ASTM B 209 07 All Sheet & Plate Alloys German Aerospace DAN 424 1288 German Sheet Requirements
Boeing BAC M 120 C 6061-T4 & T42 Sheet German Standards DIN 29 546 13 German Aluminum Specification
Cessna CMMP 025 R Metal Procurement Requirements 7075 Boeing DMS 1949 D Premium Skin Quality
Dassault CR 1.1.0.55 C Bare & Alclad Sheet Boeing DMS 2174 B MRS Requirements
German Aerospace DAN 424 1288 German Sheet Requirements British Standards EN 2092 2005 Alclad 7075-T6 Sheet
German Standards DIN 29 546 13 German Aluminum Specification Fokker TH 5.324 16 Alclad 7075 Sheet
British Standards EN 10204-3.1 2004 Test Report Specification German Aerospace WL 3.4374 1 Alclad 7075 Sheet & Plate
British Standards EN 2694 2005 Bare 6061 Sheet SAE AMS-QQ-A-250/12 Bare 7075 Sheet & Plate
6061 British Standards EN 3341 2005 Bare 6061-T4/T42 Sheet T73 ASTM ASTM B 209 07 All Sheet & Plate Alloys
German Aerospace WL 3.3214 1 6061 Sheet & Plate Cessna CMMP 025 R Metal Procurement Requirements
French Standards AIR 9048-240 1 Bare 6061-T6 Sheet Boeing DMS 2174 B MRS Requirements
SAE AMS 4027 N Bare 6061-T6/T651 Sheet & Plate SAE AMS-QQ-A-250/24 A Bare 7075-T76/T7651 Sheet & Plate
SAE AMS-QQ-A-250/11 A Bare 6061 Sheet & Plate T76 SAE AMS-QQ-A-250/25 A Alclad 7075-T76/T7651 Sheet & Plate
ASME ASME SB 209 2004 Boiler Plate Spec. (6061) ASTM ASTM B 209 07 All Sheet & Plate Alloys
Aerospatiale ASN-A3047 C Bare 6061-T6 Sheet Boeing DMS 2174 B MRS Requirements
T6 ASTM ASTM B 209 07 All Sheet & Plate Alloys German Aerospace DAN 424 1288 German Sheet Requirements
ASTM ASTM B 632 02 Bare 6061 Tread Sheet & Plate F British Standards EN 3332 2005 Alclad 7475-T762 Sheet
German Aerospace DAN 424 1288 German Sheet Requirements British Standards EN 3333 2005 Bare 7475-T762 Sheet
German Standards DIN 29 546 13 German Aluminum Specification German Aerospace DAN 424 1288 German Sheet Requirements
British Standards EN 2694 2005 Bare 6061 Sheet Boeing DMS 2234 A Alclad 7475 Sheet
German Aerospace WL 3.3214 1 6061 Sheet & Plate O Boeing DMS 2281 Bare 7475 Sheet
German Aerospace DAN 424 1288 German Sheet Requirements British Standards EN 3332 2005 Alclad 7475-T762 Sheet
T651 German Standards DIN 29 546 13 German Aluminum Specification British Standards EN 3333 2005 Bare 7475-T762 Sheet
German Aerospace WL 3.3214 1 6061 Sheet & Plate Embraer MEP 02-012 G Embraer Bare & Alclad 7475 Sheet
SAE AMS-QQ-A-250/12 Bare 7075 Sheet & Plate SAE AMS 4207 B Alclad 7475-T61 Sheet
F T16
ASTM ASTM B 209 07 All Sheet & Plate Alloys 7475 Boeing DMS 2234 A Alclad 7475 Sheet
SAE AMS 4044 L Bare 7075-O Sheet & Plate French Standards AIR 9048-290 1 Bare 7475-T761 Sheet
SAE AMS 4048 M Alclad 7075-O Sheet & Plate SAE AMS 4085 C Bare 7475-T761 Sheet
SAE AMS 4277 A Bare 7075-O Hi-Form Sheet SAE AMS 4100 D Alclad 7475-T761 Sheet
SAE AMS 4278 B Alclad 7075-O Hi-Form Sheet Bombardier BATS 2505 NC MRS Testing Specification
SAE AMS-QQ-A-250/12 Bare 7075 Sheet & Plate Boeing DMS 2174 B MRS Requirements
T761
SAE AMS-QQ-A-250/13 Alclad 7075 Sheet & Plate Boeing DMS 2233 G 7050 Plate
SAE AMS-QQ-A-250/5 A Alclad 2024 Sheet & Plate Boeing DMS 2234 A Alclad 7475 Sheet
ASTM ASTM B 209 07 All Sheet & Plate Alloys Boeing DMS 2281 Bare 7475 Sheet
Bombardier BAMS 516-011 NC Bare & Alclad 7075-O Hi-Form British Standards EN 2803 2005 Alclad 7475-T761 Sheet
O Boeing BMS 7-302 B Alclad 7075-O Hi-Form German Aerospace WL 3.4377 1 Alclad 7475 Sheet
7075 Boeing BMS 7-305 A 2024-O Hi-Form Sheet
Cessna CMMP 021 A Hi-Form O-Temper Sheet
Cessna CMMP 025 R Metal Procurement Requirements
Boeing D6-83818 Boeing Polished Skin Standards
German Aerospace DAN 424 1288 German Sheet Requirements
Boeing DMS 2130 A Premium Polished Skin Quality
Boeing DMS 2411 Hi-Form 6061, 2XXX & 7XXX
British Standards EN 2092 2005 Alclad 7075-T6 Sheet
Fokker TH 5.324 16 Alclad 7075 Sheet
German Aerospace WL 3.4374 1 Alclad 7075 Sheet & Plate
Bell 299-947-157 E MRS for Bell Helicopter
T6 French Standards AIR 9048-280 1 Alclad 7075-T6 Sheet
SAE AMS 4045 J Bare 7075-T6/T651 Sheet & Plate
www.kaiseraluminum.com | KA-SP-AFSS3-1.09
AEROSPACE COIL
SAE AMS-QQ-A-250/3 Alclad 2014 Sheet & Plate Boeing DMS 1719 D Alclad 2219 Sheet & Plate
O O
ASTM ASTM B 209 07 All Sheet & Plate Alloys McDonnell Douglas STM07-101 E Alclad 2219 Sheet
SAE AMS-QQ-A-250/3 Alclad 2014 Sheet & Plate SAE AMS 4095 C Alclad 2219-T3/T351 Sheet & Plate
T3
ASTM ASTM B 209 07 All Sheet & Plate Alloys SAE AMS-QQ-A-250/30 Bare 2219 Sheet & Plate
2014
SAE AMS-QQ-A-250/3 Alclad 2014 Sheet & Plate ASTM ASTM B 209 07 All Sheet & Plate Alloys
T4 T31
ASTM ASTM B 209 07 All Sheet & Plate Alloys 2219 Boeing BMS 7-110 F Alclad 2219 Sheet & Plate
SAE AMS-QQ-A-250/3 Alclad 2014 Sheet & Plate Boeing DMS 1719 D Alclad 2219 Sheet & Plate
T6
ASTM ASTM B 209 07 All Sheet & Plate Alloys McDonnell Douglas STM07-101 E Alclad 2219 Sheet
Boeing BAC M 196 A Alclad 2014A-F Sheet SAE AMS-QQ-A-250/30 Bare 2219 Sheet & Plate
F BSI BS L 164 Alclad 2014A-T4 Sheet T81 ASTM ASTM B 209 07 All Sheet & Plate Alloys
2014A BSI BS L166 Alclad 2014A-T4 Close Tol. Sheet McDonnell Douglas STM07-101 E Alclad 2219 Sheet
BSI BS L 164 Alclad 2014A-T4 Sheet SAE AMS 4025 L Bare 6061-O Sheet & Plate
T4
BSI BS L166 Alclad 2014A-T4 Close Tol. Sheet SAE AMS-QQ-A-250/11 A Bare 6061 Sheet & Plate
SAE AMS-QQ-A-250/5 A Alclad 2024 Sheet & Plate ASTM ASTM B 209 07 All Sheet & Plate Alloys
F
BSI BS L 110 1 Alclad 2024-F Sheet O Boeing BMS 7-312 Bare 6061-O Hi-Form Sheet
Airbus AIMS 03-04-000 3 Alum. Sheet & Plate to 12 mm. Cessna CMMP 021 A Hi-Form O-Temper Sheet
Airbus AIMS 03-04-010 5 Alclad 2024-T42 Sheet Cessna CMMP 025 R Metal Procurement Requirements
French National AIR 9048-130 1 Alclad 2024-O Sheet Boeing DMS 2411 Hi-Form 6061, 2XXX & 7XXX
SAE AMS 4035 K Bare 2024-O Sheet & Plate SAE AMS 4026 M Bare 6061-T4/T451 Sheet & Plate
SAE AMS 4040 M Alclad 2024-O Sheet & Plate 6061 SAE AMS-QQ-A-250/11 A Bare 6061 Sheet & Plate
SAE AMS 4274 A Alclad 2024-O Hi-Form Sheet T4 ASME ASME SB 209 2004 Boiler Plate Spec. (6061)
SAE AMS 4276 A Bare 2024-O Hi-Form Sheet ASTM ASTM B 209 07 All Sheet & Plate Alloys
SAE AMS-QQ-A-250/4 A Bare 2024 Sheet & Plate Cessna CMMP 025 R Metal Procurement Requirements
SAE AMS-QQ-A-250/5 A Alclad 2024 Sheet & Plate SAE AMS 4027 N Bare 6061-T6/T651 Sheet & Plate
Aerospatiale ASN-A3042 E Alclad 2024-T42 Sheet SAE AMS-QQ-A-250/11 A Bare 6061 Sheet & Plate
ASTM ASTM B 209 07 All Sheet & Plate Alloys T6 ASME ASME SB 209 2004 Boiler Plate Spec. (6061)
O British Aerospace BAEM 4075 1 Alclad 2024-T4 Sheet ASTM ASTM B 209 07 All Sheet & Plate Alloys
Boeing BMS 7-305 A Alclad 2024-O Hi-Form Sheet Cessna CMMP 025 R Metal Procurement Requirements
BSI BS L 110 1 Alclad 2024-F Sheet SAE AMS 4044 L Bare 7075-O Sheet & Plate
Cessna CMMP 021 A Hi-Form O-Temper Sheet SAE AMS 4048 M Alclad 7075-O Sheet & Plate
Cessna CMMP 025 R Metal Procurement Requirements SAE AMS 4277 A Bare 7075-O Hi-Form Sheet
German Aerospace DAN 424 1288 German Sheet Requirements SAE AMS 4278 B Alclad 7075-O Hi-Form Sheet
2024 Boeing DMS 2411 Hi-Form 6061, 2XXX & 7XXX SAE AMS-QQ-A-250/12 Bare 7075 Sheet & Plate
Embraer MEP 02-015 B Embraer Alclad 2024-O Hi-Form SAE AMS-QQ-A-250/13 Alclad 7075 Sheet & Plate
Piper Aircraft PMS-M1101 P Alclad 2024 Sheet & Plate O ASTM ASTM B 209 07 All Sheet & Plate Alloys
Rohr RMS 171 Bare 2024- Hi-Form Sheet British Aerospace BAEM 4144 1 Alclad 7075-T6 & T62 Sheet
Rohr RMS 172 Alclad 2024-O Hi-Form Sheet 7075 Bombardier BAMS 516-011 NC Bare & Alclad 7075-O Hi-Form
German Aero WL 3.1364 1 Alclad 2024 Sheet & Plate Boeing BMS 7-302 B Bare & Alclad 7075-O Hi-Form
Airbus AIMS 03-04-000 3 Alum. Sheet & Plate to 12 mm. Cessna CMMP 021 A Hi-Form O-Temper Sheet
SAE AMS 4037 N Bare 2024-T3/T351 Sheet & Plate Cessna CMMP 025 R Metal Procurement Requirements
SAE AMS 4041 Q Alclad 2024-T3/T351 Sheet & Plate Boeing DMS 2411 Hi-Form 6061, 2XXX & 7XXX
SAE AMS-QQ-A-250/4 A Bare 2024 Sheet & Plate SAE AMS 4045 J Bare 7075-T6/T651 Sheet & Plate
T3 SAE AMS-QQ-A-250/5 A Alclad 2024 Sheet & Plate SAE AMS 4049 K Alclad 7075-T6/T651 Sheet & Plate
ASTM ASTM B 209 07 All Sheet & Plate Alloys SAE AMS-QQ-A-250/12 Bare 7075 Sheet & Plate
T6
Cessna CMMP 025 R Metal Procurement Requirements SAE AMS-QQ-A-250/13 Alclad 7075 Sheet & Plate
German Aerospace DAN 424 1288 German Sheet Requirements ASTM ASTM B 209 07 All Sheet & Plate Alloys
Fokker TH 5.312 22 2024 Sheet & Plate Cessna CMMP 025 R Metal Procurement Requirements
German Aero WL 3.1354 1 Bare 2024 Sheet & Plate Boeing DMS 2234 A Alclad 7475 Sheet
SAE AMS 4297 A Bare 2024-T4 (T-Form) Sheet O Boeing DMS 2281 Bare 7475 Sheet
T4
SAE AMS-QQ-A-250/4 A Bare 2024 Sheet & Plate 7475 Embraer MEP 02-012 G Embraer Bare & Alclad 7475 Sheet
SAE AMS-QQ-A-250/4 A Bare 2024 Sheet & Plate Airbus AIMS 03-04-000 3 Alum. Sheet & Plate to 12 mm.
T81 T761
ASTM ASTM B 209 07 All Sheet & Plate Alloys Airbus AIMS 03-04-046 2 Alclad 1-Side 7475-T761
SAE AMS 4031 G Bare 2219-O Sheet & Plate This list is not necessarily up to date. Kaiser Aluminum may not be approved to produce every item listed.
SAE AMS 4096 B Alclad 2219-O Sheet & Plate
2219 O SAE AMS-QQ-A-250/30 Bare 2219 Sheet & Plate
ASTM ASTM B 209 07 All Sheet & Plate Alloys
Boeing BMS 7-110 F Alclad 2219 Sheet & Plate
www.kaiseraluminum.com | KA-SP-ACS-1.09
REFERENCE
COMPONENTS OF HEAT TREAT ALCLAD SHEET & PLATE

Component Alloys Total Specified Cladding Thickness Per Side –
Thickness of Sides % of Composite Thickness
Designation Composite Clad
Core Cladding Product (in.) Nominal Minimum Maximum
Up thru 0.024 Both 10.0% 8.0%
0.025 - 0.039 Both 7.5% 6.0%
Alclad 2014 Sheet & Plate 2014 6003
0.040 - 0.099 Both 5.0% 4.0%
0.100 and over Both 2.5% 2.0% 3.0%
Up thru 0.062 Both 5.0% 4.0%
Alclad 2024 Sheet & Plate 2024 1230
0.063 and over Both 2.5% 2.0% 3.0%
1.5% Alclad 2024 Sheet & Plate 2024 1230 0.188 and over Both 1.5% 1.2% 3.0%
Alclad One Side 2024 Up thru 0.062 One 5.0% 4.0%

2024 1230
Sheet & Plate 0.063 and over One 2.5% 2.0% 3.0%
1.5% Alclad One Side 2024
Sheet & Plate 2024 1230 0.188 and over One 1.5% 1.2% 3.0%
Up thru 0.039 Both 10.0% 8.0%

Alclad 2219 Sheet & Plate 2219 7072 0.040 - 0.099 Both 5.0% 4.0%
0.100 and over Both 2.5% 2.0% 3.0%
Alclad 6061 Sheet & Plate 6061 7072 All Both 5.0% 4.0% 6.0%
Up thru 0.062 Both 4.0% 3.2%

Alclad 7075 Sheet & Plate 7075 7072 0.063 - 0.187 Both 2.5% 2.0%
0.188 and over Both 1.5% 1.2% 3.0%
2.5% Alclad 7075 Sheet & Plate 7075 7072 0.188 and over Both 2.5% 2.0% 4.0%
Up thru 0.062 One 4.0% 3.2%

Alclad One Side 7075
Sheet & Plate 7075 7072 0.063 - 0.187 One 2.5% 2.0%
0.188 and over One 1.5% 1.2% 3.0%
2.5% Alclad One Side 7075
7075 7072 0.188 and over One 2.5% 2.0% 4.0%
Sheet & Plate
Notes
This table does not include all clad products registered with the Aluminum Association.
Cladding composition is applicable only to the aluminum or aluminum alloy bonded to the alloy ingot or slab in preparation to processing the specified
composite product. The composition of the cladding may be subsequently altered by diffusion between the core and cladding due to thermal treatment.
The average thickness per side as determined by averaging cladding thickness measurements taken at a magnification of 100 diameters on the
cross-section of a transverse sample polished and etched for microscopic examination. Maximum cladding thickness is applicable for thicknesses of
0.500 in. and greater.
www.kaiseraluminum.com | KA-SP-FRP1-1.09
REFERENCE
ESTIMATED SHEET & PLATE WEIGHT IN POUNDS

Thickness Weight ESTIMATED WEIGHTS OF VARIOUS SHEET SIZES (based on a density of .100 lb. / cu. in.)
(in.) (lbs. / sq. ft.) 24” x 72” 36” x 96” 36” x 120” 36” x 144” 48” x 96” 48” x 120” 48” x 144” 60” x 144” 60” x 180”
0.012 0.173 2.1 4.2 5.2 6.2 5.5 6.9 8.3 10.4 13.0
0.016 0.230 2.8 5.5 6.9 8.3 7.4 9.2 11.0 13.8 17.3
0.020 0.288 3.5 6.9 8.6 10.4 9.2 11.5 13.8 17.3 21.6
0.025 0.360 4.3 8.6 10.8 13.0 11.5 14.4 17.3 21.6 27.0
0.032 0.461 5.5 11.1 13.8 16.6 14.8 18.4 22.1 27.7 34.6
0.040 0.576 6.9 13.8 17.3 20.7 18.4 23.0 27.6 34.6 43.2
0.050 0.720 8.6 17.3 21.6 25.9 23.0 28.8 34.6 43.2 54.0
0.063 0.907 10.9 21.8 27.2 32.6 29.0 36.3 43.5 54.4 68.0
0.071 1.022 12.3 24.5 30.7 36.8 32.7 40.9 49.1 61.3 76.7
0.080 1.152 13.8 27.6 34.6 41.5 36.9 46.1 55.3 69.1 86.4
0.090 1.296 15.6 31.1 38.9 46.7 41.5 51.8 62.2 77.8 97.2
0.100 1.440 17.3 34.6 43.2 51.8 46.1 57.6 69.1 86.4 108.0
0.125 1.800 21.6 43.2 54.0 64.8 57.6 72.0 86.4 108.0 135.0
0.160 2.304 27.6 55.3 69.1 82.9 73.7 92.2 110.6 138.2 172.8
0.190 2.736 32.8 65.7 82.1 98.5 87.6 109.4 131.3 164.2 205.2
0.250 3.600 43.2 86.4 108.0 129.6 115.2 144.0 172.8 216.0 270.0
0.313 4.507 54.1 108.2 135.2 162.3 144.2 180.3 216.3 270.4 338.0
0.375 5.400 64.8 129.6 162.0 194.4 172.8 216.0 259.2 324.0 405.0
0.500 7.200 86.4 172.8 216.0 259.2 230.4 288.0 345.6 432.0 540.0
0.625 9.000 108.0 216.0 270.0 324.0 288.0 360.0 432.0 540.0 675.0
0.750 10.800 129.6 259.2 324.0 388.8 345.6 432.0 518.4 648.0 810.0
0.875 12.600 151.2 302.4 378.0 453.6 403.2 504.0 604.8 756.0 945.0
1.000 14.400 172.8 345.6 432.0 518.4 460.8 576.0 691.2 864.0 1,080.0
1.250 18.000 216.0 432.0 540.0 648.0 576.0 720.0 864.0 1,080.0 1,350.0
1.500 21.600 259.2 518.4 648.0 777.6 691.2 864.0 1,036.8 1,296.0 1,620.0
1.750 25.200 302.4 604.8 756.0 907.2 806.4 1,008.0 1,209.6 1,512.0 1,890.0
2.000 28.800 345.6 691.2 864.0 1,036.8 921.6 1,152.0 1,382.4 1,728.0 2,160.0
2.250 32.400 388.8 777.6 972.0 1,166.4 1,036.8 1,296.0 1,555.2 1,944.0 2,430.0
2.500 36.000 432.0 864.0 1,080.0 1,296.0 1,152.0 1,440.0 1,728.0 2,160.0 2,700.0
2.750 39.600 475.2 950.4 1,188.0 1,425.6 1,267.2 1,584.0 1,900.8 2,376.0 2,970.0
3.000 43.200 518.4 1,036.8 1,296.0 1,555.2 1,382.4 1,728.0 2,073.6 2,592.0 3,240.0
4.000 57.600 691.2 1,382.4 1,728.0 2,073.6 1,843.2 2,304.0 2,764.8 3,456.0 4,320.0
5.000 72.000 864.0 1,728.0 2,160.0 2,592.0 2,304.0 2,880.0 3,456.0 4,320.0 5,400.0
6.000 86.400 1,036.8 2,073.6 2,592.0 3,110.4 2,764.8 3,456.0 4,147.2 5,184.0 6,480.0
7.000 100.800 1,209.6 2,419.2 3,024.0 3,628.8 3,225.6 4,032.0 4,838.4 6,048.0 7,560.0
8.000 115.200 1,382.4 2,764.8 3,456.0 4,147.2 3,686.4 4,608.0 5,529.6 6,912.0 8,640.0
9.000 129.600 1,555.2 3,110.4 3,888.0 4,665.6 4,147.2 5,184.0 6,220.8 7,776.0 9,720.0
10.000 144.000 1,728.0 3,456.0 4,320.0 5,184.0 4,608.0 5,760.0 6,912.0 8,640.0 10,800.0
www.kaiseraluminum.com | KA-SP-FRP2-1.09
TABLE 7.2 Mechanical Property Limits—Heat-Treatable Alloys Q w
TENSILE STRENGTH—ksi
ALLOY SPECIFIED ELONGATION
AND THICKNESS W ULTIMATE YIELD PERCENT MIN.
TEMPER in. in 2 in. or 4D E
min. max. min. max.
2014
2014-O 0.020–0.499 .. 32.0 .. 16.0 16
Sheet and plate 0.500–1.000 .. 32.0 .. .. 10
2014-T3 0.020–0.039 59.0 .. 35.0 .. 14
Flat Sheet 0.040–0.249 59.0 .. 36.0 .. 14
2014-T4 0.020–0.249 59.0 .. 35.0 .. 14
Coiled Sheet
2014-T451 U I 0.250–0.499 58.0 .. 36.0 .. 14
Plate 0.500–1.000 58.0 .. 36.0 .. 14
1.001–2.000 58.0 .. 36.0 .. 12
2.001–3.000 57.0 .. 36.0 .. 8
2014-T42 R P 0.020–1.000 58.0 .. 34.0 .. 14
Sheet and plate
2014-T6 and T62 R P 0.020–0.039 64.0 .. 57.0 .. 6
Sheet 0.040–0.249 66.0 .. 58.0 .. 7
2014-T62 R P and T651 U 0.250–.0499 67.0 .. 59.0 .. 7
Plate 0.500–1.000 67.0 .. 59.0 .. 6
1.001–2.000 67.0 .. 59.0 .. 4
2.001–2.500 65.0 .. 58.0 .. 2
2.501–3.000 63.0 .. 57.0 .. 2
3.001–4.000 59.0 .. 55.0 .. 1
ALCLAD 2014 Y
Alclad 2014-O 0.020–0.499 .. 30.0 .. 14.0 16
Sheet and Plate 0.500–1.000 .. 32.0 T .. .. 10
Alclad 2014-T3 0.020–0.024 54.0 .. 33.0 .. 14
Flat sheet 0.025–0.039 55.0 .. 34.0 .. 14
0.040–0.249 57.0 .. 35.0 .. 15
Alclad 2014-T4 0.020–0.024 54.0 .. 31.0 .. 14
Coiled sheet 0.025–0.039 55.0 .. 32.0 .. 14
0.040–0.128 57.0 .. 34.0 .. 15
0.129–0.249 57.0 .. 34.0 .. 15
Alclad 2014-T451 U I 0.250–0.499 57.0 .. 36.0 .. 15
Plate 0.500–1.000 58.0 T .. 36.0 T .. 14
1.001–2.000 58.0 T .. 36.0 T .. 12
2.001–3.000 57.0 T .. 36.0 T .. 8
Alclad 2014-T42 R P 0.020–0.024 54.0 .. 31.0 .. 14
Sheet and plate 0.025–0.039 55.0 .. 32.0 .. 14
0.040–0.128 57.0 .. 34.0 .. 15
0.129–0.249 57.0 .. 34.0 .. 15
0.250–0.499 57.0 .. 34.0 .. 15
0.500–1.000 58.0 T .. 34.0 T .. 14
Alclad 2014-T6 and 0.020–0.024 62.0 .. 54.0 .. 7
T62 R P Sheet 0.025–0.039 63.0 .. 55.0 .. 7
0.040–0.249 64.0 .. 57.0 .. 8
Alclad 2014-T62 R P 0.250–0.499 64.0 .. 57.0 .. 8
and T651 U Plate 0.500–1.000 67.0 T .. 59.0 T .. 6
1.001–2.000 67.0 T .. 59.0 T .. 4
2.001–2.500 65.0 T .. 58.0 T .. 2
2.501–3.000 63.0 T .. 57.0 T .. 2
3.001–4.000 59.0 T .. 55.0 T .. 1
2024
2024-O 0.010–0.499 .. 32.0 .. 14.0 12
Sheet and plate 0.500–1.750 .. 32.0 .. 12
2024-T3 I 0.008–0.009 63.0 .. 42.0 .. 10
Sheet 0.010–0.020 63.0 .. 42.0 .. 12
0.021–0.128 63.0 .. 42.0 .. 15
0.129–0.249 64.0 .. 42.0 .. 15
2024-T351 U I 0.250–0.499 64.0 .. 42.0 .. 12
Plate 0.500–1.000 63.0 .. 42.0 .. 8
1.001–1.500 62.0 .. 42.0 .. 7
1.501–2.000 62.0 .. 42.0 .. 6
2.001–3.000 60.0 .. 42.0 .. 4
3.001–4.000 57.0 .. 41.0 .. 4
2024-T361 I { 0.020–0.062 67.0 .. 50.0 .. 8
Flat sheet and plate 0.063–0.249 68.0 .. 51.0 .. 9
0.250–0.499 66.0 .. 49.0 .. 9
0.500 66.0 .. 49.0 .. 10
For all numbered footnotes, see page KA-SP-AA10-1.09
This data reprinted from Aluminum standards and data 2006 with permission from The Aluminum Association, Inc. KA-SP-AA1-1.09
TABLE 7.2 Mechanical Property Limits—Heat-Treatable Alloys Q w (continued)
min. max. min. max.
2024 (Continued)
2024-T4 0.010–0.020 62.0 .. 40.0 .. 12
Sheet 0.021–0.249 62.0 .. 40.0 .. 15
2024-T42 R P 0.010–0.020 62.0 .. 38.0 .. 12
Sheet and plate 0.021–0.249 62.0 .. 38.0 .. 15
0.250–0.499 62.0 .. 38.0 .. 12
0.500–1.000 61.0 .. 38.0 .. 8
1.001–1.500 60.0 .. 38.0 .. 7
1.501–2.000 60.0 .. 38.0 .. 6
2.001–3.000 58.0 .. 38.0 .. 4
2024-T62 R P 0.010–0.499 64.0 .. 50.0 .. 5
Sheet and plate 0.500–3.000 63.0 .. 50.0 .. 5
2024-T72 R P Sheet 0.010–0.249 60.0 .. 46.0 .. 5
2024-T81 Flat sheet 0.010–0.249 67.0 .. 58.0 .. 5
2024-T851 U 0.250–0.499 67.0 .. 58.0 .. 5
Plate 0.500–1.000 66.0 .. 58.0 .. 5
1.001–1.499 66.0 .. 57.0 .. 5
2024-T861 { 0.020–0.062 70.0 .. 62.0 .. 3
0.250–0.499 70.0 .. 64.0 .. 4
0.500 70.0 .. 64.0 .. 4
ALCLAD 2024 Y
Alclad 2024-O 0.008–0.009 .. 30.0 .. 14.0 10
Sheet and plate 0.010–0.032 .. 30.0 .. 14.0 12
0.033–0.062 .. 30.0 .. 14.0 12
0.063–0.187 .. 32.0 .. 14.0 12
0.188–0.499 .. 32.0 .. 14.0 12
0.500–1.750 .. 32.0 T .. .. 12
Alclad 2024-T3 I 0.008–0.009 58.0 .. 39.0 .. 10
Sheet 0.010–0.020 59.0 .. 39.0 .. 12
0.021–0.062 59.0 .. 39.0 .. 15
0.063–0.128 61.0 .. 40.0 .. 15
0.129–0.249 62.0 .. 40.0 .. 15
Alclad 2024-T351 U I 0.250–0.499 62.0 .. 40.0 .. 12
Plate 0.500–1.000 63.0 T .. 42.0 T .. 8
1.001–1.500 62.0 T .. 42.0 T .. 7
1.501–2.000 62.0 T .. 42.0 T .. 6
2.001–3.000 60.0 T .. 42.0 T .. 4
3.001–4.000 57.0 T .. 41.0 T .. 4
Alclad 2024-T361 I { 0.020–0.062 61.0 .. 47.0 .. 8
0.188–0.249 64.0 .. 48.0 .. 9
0.250–0.499 64.0 .. 48.0 .. 9
0.500 66.0 T .. 49.0 T .. 10
Alclad 2024-T4 0.010–0.020 58.0 .. 36.0 .. 12
Sheet 0.021–0.062 58.0 .. 36.0 .. 15
0.063–0.128 61.0 .. 38.0 .. 15
Alclad 2024-T42 R P 0.008–0.009 55.0 .. 34.0 .. 10
Sheet and plate 0.010–0.020 57.0 .. 34.0 .. 12
0.021–0.062 57.0 .. 34.0 .. 15
0.063–0.187 60.0 .. 36.0 .. 15
0.188–0.249 60.0 .. 36.0 .. 15
0.250–0.499 60.0 .. 36.0 .. 12
0.500–1.000 61.0 T .. 38.0 T .. 8
1.001–1.500 60.0 T .. 38.0 T .. 7
1.501–2.000 60.0 T .. 38.0 T .. 6
2.001–3.000 58.0 T .. 38.0 T .. 4
Alclad 2024-T62 R P 0.010–0.062 60.0 .. 47.0 .. 5
Sheet and plate 0.063–0.187 62.0 .. 49.0 .. 5
0.188–0.499 62.0 .. 49.0 .. 5
Alclad 2024-T72 R P 0.010–0.062 56.0 .. 43.0 .. 5
Sheet 0.063–0.187 58.0 .. 45.0 .. 5
0.188–0.249 58.0 .. 45.0 .. 5
Alclad 2024-T81 0.010–0.062 62.0 .. 54.0 .. 5
Flat sheet 0.063–0.187 65.0 .. 56.0 .. 5
0.188–0.249 65.0 .. 56.0 .. 5
Alclad 2024-T851 U 0.250–0.499 65.0 .. 56.0 .. 5
Plate 0.500–1.000 66.0 T .. 58.0 T .. 5
min. max. min. max.
ALCLAD 2024 (Continued)
Alclad 2024-T861 { 0.020–0.062 64.0 .. 58.0 .. 3
0.188–0.249 69.0 .. 64.0 .. 4
0.250–0.499 68.0 .. 62.0 .. 4
0.500 70.0 T .. 64.0 T .. 4
11⁄2% ALCLAD 2024 Y
11⁄2% Alclad 2024-O 0.188–0.499 .. 32.0 .. 14.0 12
Sheet and plate 0.500–1.750 .. 32.0 T .. .. 12
11⁄2% Alclad 2024-T3 I 0.188–0.249 63 .. 41.0 .. 15
Sheet
11⁄2% Alclad 2024-T351 U I 0.250–0.499 63.0 .. 41.0 .. 12
Plate 0.500–1.000 63.0 T .. 42.0 T .. 8
1.001–1.500 62.0 T .. 42.0 T .. 7
1.501–2.000 62.0 T .. 42.0 T .. 6
2.001–3.000 60.0 T .. 42.0 T .. 4
3.001–4.000 57.0 T .. 41.0 T .. 4
11⁄2% Alclad 2024-T361 I { 0.188–0.249 65.0 .. 49.0 .. 9
0.500 66.0 T .. 49.0 T .. 10
11⁄2% Alclad 2024-T42 0.188–0.249 61.0 .. 37.0 .. 15
Sheet and plate R P 0.250–0.499 61.0 .. 37.0 .. 12
0.500–1.000 61.0 T .. 38.0 T .. 8
1.001–1.500 60.0 T .. 38.0 T .. 7
1.501–2.000 60.0 T .. 38.0 T .. 6
2.001–3.000 58.0 T .. 38.0 T .. 4
11⁄2% Alclad 2024-T62 R P 0.188–0.499 62.0 .. 49.0 .. 5
Sheet and plate
11⁄2% Alclad 2024-T72 R P 0.188–0.249 59.0 .. 45.0 .. 5
Sheet
11⁄2% Alclad 2024-T81 0.188–0.249 66.0 .. 57.0 .. 5
Flat sheet
11⁄2% Alclad 2024-T851 U 0.250–0.499 66.0 .. 57.0 .. 5
Plate 0.500–1.000 66.0 T .. 58.0 T .. 5
11⁄2% Alclad 2024-T861 { 0.188–0.249 70.0 .. 65.0 .. 4
0.500 70.0 T .. 64.0 T .. 4
ALCLAD ONE SIDE 2024 Y
Alclad One Side 2024-O 0.008–0.009 .. 31.0 .. 14.0 10
Sheet and plate 0.010–0.062 .. 31.0 .. 14.0 12
0.063–0.499 .. 32.0 .. 14.0 12
Alclad One Side 2024-T3 I 0.010–0.020 61.0 .. 40.0 .. 12
Sheet 0.021–0.062 61.0 .. 40.0 .. 15
0.063–0.128 62.0 .. 41.0 .. 15
0.129–0.249 63.0 .. 41.0 .. 15
Alclad One Side 2024- 0.250–0.499 63.0 .. 41.0 .. 12
T351 U I Plate
Alclad One Side 2024- 0.020–0.062 64.0 .. 48.0 .. 8
T361 I { Sheet and plate 0.063–0.249 66.0 .. 49.0 .. 9
0.250–0.499 65.0 .. 48.0 .. 9
Alclad One Side 2024-T42 R P 0.010–0.020 59.0 .. 35.0 .. 12
Sheet and plate 0.021–0.062 59.0 .. 36.0 .. 15
0.063–0.249 61.0 .. 37.0 .. 15
0.250–0.499 61.0 .. 37.0 .. 12
Sheet and plate 0.063–0.499 63.0 .. 49.0 .. 5
Flat sheet 0.063–0.249 59.0 .. 45.0 .. 5
Alclad One Side 2024-T81 0.010–0.062 64.0 .. 56.0 .. 5
Flat sheet 0.063–0.249 66.0 .. 57.0 .. 5
Alclad One Side 2024-T851 U 0.250–0.499 66.0 .. 57.0 .. 5
Plate
Alclad One Side 2024-T861 { 0.020–0.062 67.0 .. 60.0 .. 3
Sheet and plate 0.063–0.249 70.0 .. 65.0 .. 4
0.250–0.499 69.0 .. 63.0 .. 4
min. max. min. max.
11⁄2% ALCLAD ONE SIDE 2024 Y
11⁄2% Alclad One Side 2024-O 0.188–0.499 .. 32.0 .. 14.0 12
Sheet and plate
11⁄2% Alclad One Side 2024- 0.188–0.249 63.0 .. 41.0 .. 15
T3 I Sheet
11⁄2% Alclad One Side 2024- 0.250–0.499 63.0 .. 41.0 .. 12
T351 U I Plate
11⁄2% Alclad One Side 2024- 0.188–0.249 66.0 .. 49.0 .. 9
T361 I { Sheet and plate 0.250–0.499 65.0 .. 48.0 .. 9
11⁄2% Alclad One Side 2024- 0.188–0.249 61.0 .. 37.0 .. 15
T42 R P Sheet and plate 0.250–0.499 61.0 .. 37.0 .. 12
11⁄2% Alclad One Side 2024- 0.188–0.499 63.0 .. 49.0 .. 5
T62 R P Sheet and plate
11⁄2% Alclad One Side 2024- 0.188–0.249 59.0 .. 45.0 .. 5
T72 R P Flat sheet
11⁄2% Alclad One Side 2024- 0.188–0.249 66.0 .. 57.0 .. 5
T81 Flat sheet
11⁄2% Alclad One Side 2024- 0.250–0.499 66.0 .. 57.0 .. 5
T851 U Plate
11⁄2% Alclad One Side 2024- 0.188–0.249 70.0 .. 65.0 .. 4
T861 { Sheet and plate 0.250–0.499 69.0 .. 63.0 .. 4
2036
2036-T4 0.025–0.125 42.0 .. 23.0 .. 20
Flat sheet
2124
ALLOY SPECIFIED AXIS OF ELONGATION
AND THICKNESS W TEST ULTIMATE YIELD PERCENT MIN.
TEMPER in. SPECIMEN in 2 in. or 4D E
min. max. min. max.
2124-T351 U 1.000–1.499 Longitudinal 61.0 .. 45.0 .. 14
Plate Long Transverse 62.0 .. 42.0 .. 13
1.500–2.000 Longitudinal 61.0 .. 45.0 .. 14
Long Transverse 62.0 .. 42.0 .. 13
Short Transverse 58.0 .. 38.0 .. 4.5
2.001–3.000 Longitudinal 61.0 .. 45.0 .. 14
Short Transverse 58.0 .. 38.0 .. 4
2124-T851 U r 1.000–2.000 Longitudinal 66.0 .. 57.0 .. 6
Short Transverse 64.0 e .. 55.0 e .. 1.5 e
2.001–3.000 Longitudinal 65.0 .. 57.0 .. 6
3.001–4.000 Longitudinal 65.0 .. 56.0 .. 5
4.001–5.000 Longitudinal 64.0 .. 55.0 .. 5
5.001–6.000 Longitudinal 63.0 .. 54.0 .. 5
min. max. min. max.
2219
2219-O 0.020–2.000 .. 32.0 .. 16.0 12
Sheet and plate
2219-T31 I 0.020–0.039 46.0 .. 29.0 .. 8
Flat sheet 0.040–0.249 46.0 .. 28.0 .. 10
2219-T351 U I 0.250–2.000 46.0 .. 28.0 .. 10
Plate 2.001–3.000 44.0 .. 28.0 .. 10
3.001–4.000 42.0 .. 27.0 .. 9
4.001–5.000 40.0 .. 26.0 .. 9
5.001–6.000 39.0 .. 25.0 .. 8
2219-T37 I 0.020–0.039 49.0 .. 38.0 .. 6
2.001–2.500 49.0 .. 37.0 .. 6
2.501–3.000 47.0 .. 36.0 .. 6
3.001–4.000 45.0 .. 35.0 .. 5
4.001–5.000 43.0 .. 34.0 .. 4
2219-T62 R P 0.020–0.039 54.0 .. 36.0 .. 6
Sheet and plate 0.040–0.249 54.0 .. 36.0 .. 7
0.250–1.000 54.0 .. 36.0 .. 8
1.001–2.000 54.0 .. 36.0 .. 7
2219-T81 0.020–0.039 62.0 .. 46.0 .. 6
Flat sheet 0.040–0.249 62.0 .. 46.0 .. 7
2219-T851 U 0.250–1.000 62.0 .. 46.0 .. 8
Plate 1.001–2.000 62.0 .. 46.0 .. 7
2.001–3.000 62.0 .. 45.0 .. 6
3.001–4.000 60.0 .. 44.0 .. 5
4.001–5.000 59.0 .. 43.0 .. 5
5.001–6.000 57.0 .. 42.0 .. 4
2219-T87 0.020–0.039 64.0 .. 52.0 .. 5
0.250–1.000 64.0 .. 51.0 .. 7
1.001–2.000 64.0 .. 51.0 .. 6
2.001–3.000 64.0 .. 51.0 .. 6
3.001–4.000 62.0 .. 50.0 .. 4
4.001–5.000 61.0 .. 49.0 .. 3
ALCLAD 2219 Y
Alclad 2219-O 0.020–0.499 .. 32.0 .. 16.0 12
Sheet and plate 0.500–2.000 .. 32.0 T .. 16.0 T ..
Alclad 2219-T31 I 0.040–0.099 42.0 .. 25.0 .. 10
Flat sheet 0.100–0.249 44.0 .. 26.0 .. 10
Alclad 2219-T351 U I Plate 0.250–0.499 44.0 .. 26.0 .. 10
Alclad 2219-T37 I 0.040–0.099 45.0 .. 34.0 .. 6
0.250–0.499 47.0 .. 35.0 .. 6
Alclad 2219-T62 R P 0.020–0.039 44.0 .. 29.0 .. 6
Sheet and plate 0.040–0.099 49.0 .. 32.0 .. 7
0.100–0.249 51.0 .. 34.0 .. 7
0.250–0.499 51.0 .. 34.0 .. 8
0.500–1.000 54.0 T .. 36.0 T .. 8
1.001–2.000 54.0 T .. 36.0 T .. 7
Alclad 2219-T81 0.020–0.039 49.0 .. 37.0 .. 6
Flat sheet 0.040–0.099 55.0 .. 41.0 .. 7
0.100–0.249 58.0 .. 43.0 .. 7
Alclad 2219-T851 U Plate 0.250–0.499 58.0 .. 42.0 .. 8
Alclad 2219-T87 0.040–0.099 57.0 .. 46.0 .. 6
0.250–0.499 60.0 .. 48.0 .. 7
6061
6061-O 0.006–0.007 .. 22.0 .. 12.0 10
Sheet and plate 0.008–0.009 .. 22.0 .. 12.0 12
0.010–0.020 .. 22.0 .. 12.0 14
0.021–0.128 .. 22.0 .. 12.0 16
0.129–0.499 .. 22.0 .. 12.0 18
0.500–1.000 .. 22.0 .. .. 18
1.001–3.000 .. 22.0 .. .. 16
6061-T4 0.006–0.007 30.0 .. 16.0 .. 10
Sheet 0.008–0.009 30.0 .. 16.0 .. 12
0.010–0.020 30.0 .. 16.0 .. 14
0.021–0.249 30.0 .. 16.0 .. 16
min. max. min. max.
6061 (Continued)
6061-T451 U I 0.250–1.000 30.0 .. 16.0 .. 18
Plate 1.001–3.000 30.0 .. 16.0 .. 16
6061-T42 R P 0.006–0.007 30.0 .. 14.0 .. 10
Sheet and plate 0.008–0.009 30.0 .. 14.0 .. 12
0.010–0.020 30.0 .. 14.0 .. 14
0.021–0.249 30.0 .. 14.0 .. 16
0.250–1.000 30.0 .. 14.0 .. 18
1.001–3.000 30.0 .. 14.0 .. 16
6061-T6 and T62 R P 0.006–0.007 42.0 .. 35.0 .. 4
Sheet 0.008–0.009 42.0 .. 35.0 .. 6
0.010–0.020 42.0 .. 35.0 .. 8
0.021–0.249 42.0 .. 35.0 .. 10
6061-T62 R P and 0.250–0.499 42.0 .. 35.0 .. 10
T651 U Plate 0.500–1.000 42.0 .. 35.0 .. 9
1.001–2.000 42.0 .. 35.0 .. 8
2.001–4.000 42.0 .. 35.0 .. 6
4.001–6.000 O 40.0 .. 35.0 .. 6
ALCLAD 6061 Y
Alclad 6061-O 0.010–0.020 .. 20.0 .. 12.0 14
Sheet and plate 0.021–0.128 .. 20.0 .. 12.0 16
0.129–0.499 .. 20.0 .. 12.0 18
0.500–1.000 .. 22.0 T .. .. 18
1.001–3.000 .. 22.0 T .. .. 16
Alclad 6061-T4 0.010–0.020 27.0 .. 14.0 .. 14
Sheet 0.021–0.249 27.0 .. 14.0 .. 16
Alclad 6061-T451 U I 0.250–0.499 27.0 .. 14.0 .. 18
Plate 0.500–1.000 30.0 T .. 16.0 T .. 18
1.001–3.000 30.0 T .. 16.0 T .. 16
Alclad 6061-T42 R P 0.010–0.020 27.0 .. 12.0 .. 14
Sheet and plate 0.021–0.249 27.0 .. 12.0 .. 16
0.250–0.499 27.0 .. 12.0 .. 18
0.500–1.000 30.0 T .. 14.0 T .. 18
1.001–3.000 30.0 T .. 14.0 T .. 16
Alclad 6061-T6 0.010–0.020 38.0 .. 32.0 .. 8
and T62 R P Sheet 0.021–0.249 38.0 .. 32.0 .. 10
Alclad 6061-T62 R P 0.250–0.499 38.0 .. 32.0 .. 10
and T651 U Plate 0.500–1.000 42.0 T .. 35.0 T .. 9
1.001–2.000 42.0 T .. 35.0 T .. 8
2.001–3.000 42.0 T .. 35.0 T .. 6
3.001–4.000 42.0 T .. 35.0 T .. 6
4.001–5.000 O 40.0 T .. 35.0 T .. 6
min. max. min. max.
7050
7050- 0.250–2.000 Longitudinal 74.0 .. 64.0 .. 10
T7451 r t y i Plate Long Transverse
Transverse 74.0 .. 64.0 .. 9
2.001–3.000 Longitudinal 73.0 .. 63.0 .. 9
3.001–4.000 Longitudinal 72.0 .. 62.0 .. 9
4.001–5.000 Longitudinal 71.0 .. 61.0 .. 9
5.001–6.000 Longitudinal 70.0 .. 60.0 .. 8
6.001–7.000 Longitudinal 69.0 .. 59.0 .. 7
7.001–8.000 Longitudinal 68.0 .. 58.0 .. 6
min. max. min. max.
7050 (Continued)
7050-T7651 r u o 0.250–1.000 Longitudinal 76.0 .. 66.0 .. 9
1.001–1.500 Longitudinal 77.0 .. 67.0 .. 9
1.501–2.000 Longitudinal 76.0 .. 66.0 .. 9
2.001–3.000 Longitudinal 76.0 .. 66.0 .. 8
min. max. min. max.
7075
7075-O 0.015–0.499 .. 40.0 .. 21.0 10
Sheet and plate 0.500–2.000 .. 40.0 .. .. 10
7075-T6 and T62 R P 0.008–0.011 74.0 .. 63.0 .. 5
Sheet 0.012–0.039 76.0 .. 67.0 .. 8
0.040–0.062 78.0 .. 68.0 .. 9
0.063–0.125 78.0 .. 68.0 .. 9
0.126–0.187 79.0 .. 69.0 .. 9
0.188–0.249 80.0 .. 69.0 .. 9
7075-T62 R P and T651U 0.250–0.499 78.0 .. 67.0 .. 9
Plate 0.500–1.000 78.0 .. 68.0 .. 7
1.001–2.000 77.0 .. 67.0 .. 6
2.001–2.500 76.0 .. 64.0 .. 5
2.501–3.000 72.0 .. 61.0 .. 5
3.001–3.500 71.0 .. 58.0 .. 5
3.501–4.000 67.0 .. 54.0 .. 3
7075-T73 Sheet 0.040–0.249 67.0 .. 56.0 .. 8
7075-T7351 U } 0.250–1.000 69.0 .. 57.0 .. 7
Plate 1.001–2.000 69.0 .. 57.0 .. 6
2.001–2.500 66.0 .. 52.0 .. 6
2.501–3.000 64.0 .. 49.0 .. 6
3.001–3.500 63.0 .. 49.0 .. 6
3.501–4.000 61.0 .. 48.0 .. 6
7075-T76 q Sheet 0.063–0.125 73.0 .. 62.0 .. 8
0.126–0.249 73.0 .. 62.0 .. 8
7075-T7651 U q 0.250–0.499 72.0 .. 61.0 .. 8
Plate 0.500–1.000 71.0 .. 60.0 .. 6
1.001–2.000 71.0 .. 60.0 .. 5
ALCLAD 7075 Y
Alclad 7075-O 0.008–0.014 .. 36.0 .. 20.0 9
Sheet and plate 0.015–0.062 .. 36.0 .. 20.0 10
0.063–0.187 .. 38.0 .. 20.0 10
0.188–0.499 .. 39.0 .. 21.0 10
0.500–1.000 .. 40.0 T .. .. 10
Alclad 7075-T6 and T62 R P 0.008–0.011 68.0 .. 58.0 .. 5
Sheet 0.012–0.039 71.0 .. 61.0 .. 8
0.040–0.062 72.0 .. 62.0 .. 9
0.063–0.125 74.0 .. 64.0 .. 9
0.126–0.187 74.0 .. 64.0 .. 9
0.188–0.249 76.0 .. 65.0 .. 9
Alclad 7075-T62 R P 0.250–0.499 75.0 .. 65.0 .. 9
and T651 U 0.500–1.000 78.0 T .. 68.0 T .. 7
Plate 1.001–2.000 77.0 T .. 67.0 T .. 6
2.001–2.500 76.0 T .. 64.0 T .. 5
2.501–3.000 72.0 T .. 61.0 T .. 5
3.001–3.500 71.0 T .. 58.0 T .. 5
3.501–4.000 67.0 T .. 54.0 T .. 3
Alclad 7075-T73 0.040–0.062 63.0 .. 51.0 .. 8
Sheet 0.063–0.187 64.0 .. 52.0 .. 8
0.188–0.249 66.0 .. 54.0 .. 8
Alclad 7075-T7351 U } 0.250–0.499 66.0 .. 54.0 .. 8
Plate 0.500–1.000 69.0 T .. 57.0 T .. 7
min. max. min. max.
ALCLAD 7075 Y (Continued)
Alclad 7075-T76 q 0.040–0.062 67.0 .. 56.0 .. 8
Sheet 0.063–0.125 68.0 .. 57.0 .. 8
0.125–0.187 68.0 .. 57.0 .. 8
0.188–0.249 70.0 .. 59.0 .. 8
Alclad 7075-T7651 U q 0.250–0.499 69.0 .. 58.0 .. 8
Plate 0.500–1.000 71.0 T .. 60.0 T .. 6
21⁄2% ALCLAD 7075 Y
21⁄2% Alclad 7075-O 0.188–0.499 .. 39.0 .. 20.0 10
Sheet and plate 0.500–1.000 .. 40.0 T .. .. 10
21⁄2% Alclad 7075-T6 and 0.188–0.249 74.0 .. 64.0 .. 8
T62 R P Sheet
21⁄2% Alclad 7075-T62 R P 0.250–0.499 74.0 .. 64.0 .. 9
and T651 U 0.500–1.000 78.0 T .. 68.0 T .. 7
Plate 1.001–2.000 77.0 T .. 67.0 T .. 6
2.001–2.500 76.0 T .. 64.0 T .. 5
2.501–3.000 72.0 T .. 61.0 T .. 5
3.001–3.500 71.0 T .. 58.0 T .. 5
3.501–4.000 67.0 T .. 54.0 T .. 3
21⁄2% Alclad 7075-T73 0.188–0.249 64.0 .. 53.0 .. 8
Sheet
21⁄2% Alclad 7075-T7351 U } 0.250–0.499 65.0 .. 54.0 .. 8
Plate 0.500–1.000 69.0 T .. 57.0 T .. 7
21⁄2% Alclad 7075-T76 q 0.188–0.249 69.0 .. 59.0 .. 8
Sheet
21⁄2% Alclad 7075-T7651 U q 0.250–0.499 68.0 .. 58.0 .. 8
Plate 0.500–1.000 71.0 T .. 60.0 T .. 6
ALCLAD ONE SIDE 7075 Y
Alclad One Side 7075-O 0.015–0.062 .. 38.0 .. 21.0 10
Sheet and plate 0.063–0.187 .. 39.0 .. 21.0 10
0.188–0.499 .. 39.0 .. 21.0 10
0.500–1.000 .. 40.0 T .. .. 10
Alclad One Side 0.008–0.011 71.0 .. 60.0 .. 5
7075-T6 and T62 R P Sheet 0.012–0.039 74.0 .. 64.0 .. 8
0.040–0.062 75.0 .. 65.0 .. 9
0.063–0.125 76.0 .. 66.0 .. 9
0.126–0.187 77.0 .. 66.0 .. 9
0.188–0.249 78.0 .. 67.0 .. 9
Alclad One Side 7075 0.250–0.499 76.0 .. 66.0 .. 9
T62 R P and T651 U Plate 0.500–1.000 78.0 T .. 68.0 T .. 7
1.001–2.000 77.0 T .. 67.0 T .. 6
21⁄2% ALCLAD ONE SIDE 7075 Y
21⁄2% Alclad One Side 7075-O 0.188–0.499 .. 39.0 .. 21.0 10
Sheet and plate 0.500–1.000 .. 40.0 T .. .. 10
21⁄2% Alclad One Side 0.188–0.249 76.0 .. 65.0 .. 8
7075-T6 and T62 R P Sheet
21⁄2% Alclad One Side 7075 0.250–0.499 76.0 .. 65.0 .. 9
T62 R P and T651 U 0.500–1.000 78.0 T .. 68.0 T .. 7
Plate 1.001–2.000 77.0 T .. 67.0 T .. 6
7008 ALCLAD 7075 Y
7008 Alclad 7075-O 0.015–0.062 .. 40.0 .. 21.0 10
Sheet and plate 0.063–0.187 .. 40.0 .. 21.0 10
0.188–0.499 .. 40.0 .. 21.0 10
0.500–2.000 .. 40.0T .. .. 10
7008 Alclad 7075-T6 and 0.015–0.039 73.0 .. 63.0 .. 7
T62 R P Sheet 0.040–0.062 75.0 .. 65.0 .. 8
0.063–0.087 75.0 .. 65.0 .. 8
0.188–0.249 76.0 .. 66.0 .. 8
7008 Alclad 7075-T62 R P 0.250–0.499 76.0 .. 66.0 .. 9
and T651 U Plate 0.500–1.000 78.0 T .. 68.0 T .. 7
1.001–2.000 77.0 T .. 67.0 T .. 6
2.001–2.500 76.0 T .. 64.0 T .. 5
2.501–3.000 72.0 T .. 61.0 T .. 5
3.001–3.500 71.0 T .. 58.0 T .. 5
3.501–4.000 67.0 T .. 54.0 T .. 3
min. max. min. max.
7008 ALCLAD 7075 Y (Continued)
7008 Alclad 7075-T76 q 0.040–0.062 70.0 .. 59.0 .. 8
Sheet 0.063–0.187 71.0 .. 60.0 .. 8
0.188–0.249 72.0 .. 61.0 .. 8
7008 Alclad 7075-T7651 U q 0.250–0.499 71.0 .. 60.0 .. 8
Plate 0.500–1.000 71.0 T .. 60.0 T .. 6
7178
7178-O 0.015–0.499 .. 40.0 .. 21.0 10
Sheet and plate 0.500 .. 40.0 .. .. 10
7178-T6 and T62 R P 0.015–0.044 83.0 .. 72.0 .. 7
Sheet 0.045–0.249 84.0 .. 73.0 .. 8
7178-T62 R P and 0.250–0.499 84.0 .. 73.0 .. 8
T651 U 0.500–1.000 84.0 .. 73.0 .. 6
Plate 1.001–1.500 84.0 .. 73.0 .. 4
1.501–2.000 80.0 .. 70.0 .. 3
7178-T76 q Sheet 0.045–0.249 75.0 .. 64.0 .. 8
7178-T7651 U q 0.250–0.499 74.0 .. 63.0 .. 8
Plate 0.500–1.000 73.0 .. 62.0 .. 6
ALCLAD 7178 Y
Alclad 7178-O 0.015–0.062 .. 36.0 .. 20.0 10
Sheet and plate 0.063–0.187 .. 38.0 .. 20.0 10
0.188–0.499 .. 40.0 .. 21.0 10
0.500 .. 40.0 .. .. 10
Alclad 7178-T6 and 0.015–0.044 76.0 .. 66.0 .. 7
T62 R P Sheet 0.045–0.062 78.0 .. 68.0 .. 8
0.063–0.187 80.0 .. 70.0 .. 8
0.188–0.249 82.0 .. 71.0 .. 8
Alclad 7178-T62 R P 0.250–0.499 82.0 .. 71.0 .. 8
and T651 U 0.500–1.000 84.0 T .. 73.0 T .. 6
Plate 1.001–1.500 84.0 T .. 73.0 T .. 4
1.501–2.000 80.0 T .. 70.0 T .. 3
Alclad 7178-T76 q 0.045–0.062 71.0 .. 60.0 .. 8
Sheet 0.063–0.187 71.0 .. 60.0 .. 8
0.188–0.249 73.0 .. 61.0 .. 8
Alclad 7178-T7651 U q 0.250–0.499 72.0 .. 60.0 .. 8
Plate 0.500–1.000 73.0 T .. 62.0 T .. 6
7475
7475-T61 0.040–0.249 75.0 .. 64.0 .. 9
Sheet
min. max. min. max.
7475-T7351 0.250–1.500 Longitudinal 71.0 .. 60.0 .. 10

1.001–1.500 Short Transverse 67.0 p .. 56.0 p .. 4p
1.501–2.000 Longitudinal 70.0 .. 58.0 .. 10
2.001–2.500 Longitudinal 69.0 .. 57.0 .. 10
2.501–3.000 Longitudinal 68.0 .. 56.0 .. 10
3.001–3.500 Longitudinal 65.0 .. 53.0 .. 10
3.501–4.000 Longitudinal 64.0 .. 52.0 .. 9
TABLE 7.2 Mechanical Property Limits—Heat-Treatable Alloys Q w (concluded)
7475 (Continued)
min. max. min. max.
7475-T761 Sheet 0.040–0.249 71.0 .. 60.0 .. 9
min. max. min. max.
7475-T7651 0.250–0.499 Longitudinal 70.0 .. 60.0 .. 9
0.500–1.000 Longitudinal 69.0 .. 59.0 .. 8
1.001–1.500 Longitudinal 69.0 .. 59.0 .. 6
ALCLAD 7475 Y
min. max. min. max.
Alclad 7475-T61 0.040–0.062 69.0 .. 59.0 .. 9
Sheet 0.063–0.187 70.0 .. 60.0 .. 9
0.188–0.249 72.0 .. 61.0 .. 9
Alclad 7475-T761 0.040–0.062 66.0 .. 55.0 .. 9
Sheet 0.063–0.187 68.0 .. 57.0 .. 9
0.188–0.249 70.0 .. 60.0 .. 9
Footnotes for Table 7.2

(Page numbers and tables noted within footnotes reference pages in Aluminum standards and data 2006.)
Q The data base and criteria upon which these mechanical property limits Also, material 0.750 inch and thicker, when tested in accordance with ASTM
are established are outlined on page 6-1 under “Mechanical Properties.” G47 in the short transverse direction of stress level of 25 ksi, will exhibit no
W Type of specimen used depends on thickness of material; see “Sampling evidence of stress corrosion cracking. Capability of individual lots to resist
and Testing,” pages 4-1 through 4-5 exfoliation corrosion and stress corrosion cracking is determined by testing
E D represents specimen diameter. the previously selected tensile test sample in accordance with the applicable
R These properties can usually be obtained by the user, when the material lot acceptance criteria outlined on pages 6-7 and 6-8.
is properly solution heat treated or solution and precipitation heat treated w Processes such as flattening, leveling, or straightening coiled products
from the O (annealed) or F (as fabricated) temper. These properties also subsequent to shipment by the producer may alter the mechanical proper-
apply to samples of material in the O or F tempers, which are solution heat ties of the metal (refer to Certification, Section 4).
treated or solution and precipitation treated by the producer to determine e Applicable only to 1.500 inch and greater thickness.
that the material will respond to proper heat treatment. Properties attained r See Table 6.6 for fracture toughness limits.
by the user, however, may be lower than those listed if the material has been t T7451 temper, although not previously registered, has appeared in the
formed or otherwise cold or hot worked, particularly in the annealed temper, literature and in some specifications as T73651.
prior to solution heat treatment. y Material in this temper, 0.750 inch and thicker, when tested in accordance
T This table specifies the properties applicable to the test specimens, and with ASTM G47 in the short transverse direction at a stress level of 35 ksi,
since for plate 0.500 or over in thickness the cladding material is removed will exhibit no evidence of stress corrosion cracking. Capability of individual
during preparation of the test specimens, the listed properties are applicable lots to resist stress corrosion is determined by testing the previously selected
to the core material only. Tensile and yield strengths of the composite plate tensile test sample in accordance with the applicable lot acceptance criteria
are slightly lower depending upon the thickness of the cladding. outlined on pages 6-7 and 6-8.
Y See page 6-4 for specific cladding thicknesses. u Material in this temper, 0.750 inch and thicker, when tested in accordance
U For stress-relieved tempers the characteristics and properties other than with ASTM G47 in the short transverse direction at a stress level of 25 ksi,
those specified may differ somewhat from the corresponding characteristics will exhibit no evidence of stress corrosion cracking. Capability of individual
and properties of material in the basic temper. lots to resist stress corrosion is determined by testing the previously selected
I Upon artificial aging, T3 /T31, T37, T351, T361 and T451 temper material tensile test sample in accordance with the applicable lot acceptance criteria
shall be capable of developing the mechanical properties applicable to the outlined on pages 6-7 and 6-8.
T81, T87, T851, T861 and T651 tempers, respectively. i Material in this temper, when tested at any plane in accordance with ASTM
O The properties for this thickness apply only to the T651 temper. G34, will exhibit exfoliation less than that shown in Photo EB, Figure 2, of
P This temper is not available from the material producer. ASTM G34. Capability of individual lots to resist exfoliation corrosion and
{ Tempers T361 and T861 formerly designated T36 and T86, respectively. stress corrosion cracking is determined by testing the previously selected
} Material in this temper, 0.750 inch and thicker, when tested in accor- tensile test sample in accordance with the applicable lot acceptance criteria
dance with ASTM G47 in the short transverse direction at a stress level of outlined on pages 6-7 and 6-8.
75 percent of the specified minimum yield strength, will exhibit no evidence o Material in this temper, when tested at 1/10 plane in accordance with ASTM
of stress corrosion cracking. Capability of individual lots to resist stress cor- G34, will exhibit exfoliation less than that shown in Photo EB, Figure 2, of
rosion is determined by testing the previously selected tensile test sample ASTM G34. Capability of individual lots to resist exfoliation corrosion and
in accordance with the applicable lot acceptance criteria outlined on pages stress corrosion cracking is determined by testing the previously selected
6-7 and 6-8. tensile test sample in accordance with the applicable lot acceptance criteria
q Material in this temper, when tested in accordance with ASTM G34, will outlined on pages 6-7 through 6-10.
exhibit exfoliation less than that shown in Photo EB, Figure 2, of ASTM G34. p Applies to 1.500 in. only.
TABLE 7.7a Sheet and Plate Thickness Tolerances Q (Applicable to All Alloys Not Included in the
Aerospace Alloys Table 7.7b or Not Specified for Aerospace Applications)
NOTE: ALSO APPLICABLE TO ALLOYS WHEN SUPPLIED AS ALCLAD.
SPECIFIED WIDTH—in.
SPECIFIED
THICKNESS, Up thru Over 39.37 Over 59.06 Over 78.74 Over 98.43 Over 118.11 Over 137.80 Over 157.48
in. 39.37 Thru 59.06 Thru 78.74 Thru 98.43 Thru 118.11 Thru 137.80 Thru 157.48 Thru 177.17
Over Thru TOLERANCES—in. plus and minus
0.0059 0.010 0.0010 0.0015 .. .. .. .. .. ..
0.010 0.016 0.0010 0.0015 .. .. .. .. .. ..
0.016 0.025 0.0015 0.0020 0.0030 0.0035 .. .. .. ..
0.025 0.032 0.0020 0.0025 0.0035 0.0040 .. .. .. ..
0.032 0.039 0.0020 0.0030 0.0035 0.0045 0.006 .. .. ..
0.039 0.047 0.0025 0.0035 0.0045 0.006 0.007 0.008 .. ..
0.047 0.063 0.0030 0.0035 0.0050 0.006 0.007 0.009 .. ..
0.063 0.079 0.0035 0.0040 0.006 0.007 0.008 0.010 .. ..
0.079 0.098 0.0035 0.0045 0.006 0.007 0.009 0.011 .. ..
0.098 0.126 0.0045 0.006 0.007 0.009 0.011 0.013 .. ..
0.126 0.158 0.006 0.007 0.009 0.011 0.013 0.015 .. ..
0.158 0.197 0.007 0.009 0.011 0.013 0.015 0.018 .. ..
0.197 0.248 0.009 0.011 0.013 0.015 0.018 0.022 0.027 ..
0.248 0.315 0.012 0.014 0.015 0.018 0.022 0.027 0.035 0.043
0.315 0.394 0.015 0.017 0.020 0.023 0.027 0.033 0.041 0.051
0.394 0.630 0.023 0.023 0.027 0.032 0.035 0.043 0.053 0.065
0.630 0.984 0.031 0.031 0.037 0.043 0.047 0.058 0.070 0.085
0.984 1.575 0.039 0.039 0.047 0.055 0.065 0.075 0.090 0.105
1.575 2.362 0.055 0.055 0.060 0.070 0.085 0.100 0.115 ..
2.362 3.150 0.075 0.075 0.085 0.100 0.105 0.125 .. ..
3.150 3.937 0.100 0.100 0.115 0.125 0.130 0.160 .. ..
3.937 6.299 0.130 0.130 0.145 0.165 .. .. .. ..
6.300 8.000 0.160 0.160 0.160 0.165 .. .. .. ..
TABLE 7.7b Sheet and Plate Thickness Tolerances Q (Applicable to All Alloys Specified for
Aerospace Applications)
(INCLUDES AEROSPACE ALLOYS 2014, 2024, 2124, 2219, 2324, 2419, 7050, 7075, 7150, 7178 and 7475)
NOTE: ALSO APPLICABLE TO ALLOYS WHEN SUPPLIED AS ALCLAD.
Over Over Over Over Over Over Over Over Over Over Over
SPECIFIED Up 39.37 47.24 55.12 59.06 70.87 78.74 86.61 98.43 118.11 137.80 157.48
THICKNESS thru thru thru thru thru thru thru thru thru thru thru thru
39.37 47.24 55.12 59.06 70.87 78.74 86.61 98.43 118.11 137.80 157.48 177.17
Over Thru TOLERANCE—in. plus and minus
0.0059 0.010 0.0010 0.0020 0.0020 0.0020 .. .. .. .. .. .. .. ..
0.010 0.016 0.0015 0.0025 0.0025 0.0025 .. .. .. .. .. .. .. ..
0.016 0.025 0.0015 0.0025 0.0025 0.0025 .. .. .. .. .. .. .. ..
0.025 0.032 0.0015 0.0015 0.0020 0.0030 0.0030 .. .. .. .. .. .. ..
0.032 0.039 0.0015 0.0015 0.0020 0.0030 0.0030 0.0035 0.0035 0.007 .. .. .. ..
0.039 0.047 0.0020 0.0020 0.0020 0.0030 0.0030 0.0035 0.0035 0.008 0.010 0.011 .. ..
0.047 0.063 0.0020 0.0020 0.0030 0.0030 0.0030 0.0035 0.0035 0.009 0.011 0.013 .. ..
0.063 0.079 0.0020 0.0020 0.0030 0.0035 0.0035 0.0035 0.0035 0.010 0.013 0.015 .. ..
0.079 0.098 0.0025 0.0025 0.0035 0.0040 0.0040 0.0045 0.0045 0.011 0.015 0.018 .. ..
0.098 0.126 0.0035 0.0035 0.0035 0.0045 0.0045 0.0045 0.0045 0.013 0.016 0.020 .. ..
0.126 0.158 0.0040 0.0040 0.0045 0.007 0.007 0.009 0.009 0.015 0.018 0.022 .. ..
0.158 0.197 0.006 0.007 0.007 0.009 0.009 0.011 0.011 0.018 0.022 0.026 .. ..
0.197 0.248 0.009 0.012 0.012 0.012 0.017 0.017 0.021 0.021 0.025 0.029 .. ..
0.248 0.315 0.012 0.015 0.015 0.015 0.019 0.019 0.024 0.024 0.029 0.033 0.041 0.051
0.315 0.394 0.017 0.018 0.018 0.018 0.022 0.022 0.028 0.028 0.033 0.039 0.047 0.059
0.394 0.630 0.023 0.023 0.023 0.023 0.028 0.028 0.033 0.033 0.039 0.047 0.059 0.070
0.630 0.984 0.031 0.031 0.031 0.031 0.037 0.037 0.043 0.043 0.051 0.060 0.070 0.085
0.984 1.575 0.039 0.039 0.039 0.039 0.047 0.047 0.055 0.055 0.065 0.075 0.090 0.105
1.575 2.362 0.055 0.055 0.055 0.055 0.060 0.060 0.070 0.070 0.090 0.100 0.115 ..
2.362 3.150 0.075 0.075 0.075 0.075 0.085 0.085 0.100 0.100 0.110 0.125 .. ..
3.150 3.937 0.100 0.100 0.100 0.100 0.115 0.115 0.130 0.130 0.150 0.160 .. ..
3.937 6.299 0.130 0.130 0.130 0.130 0.145 0.145 0.165 0.165 .. .. .. ..
6.300 8.000 0.160 0.160 0.160 0.160 0.160 0.160 0.165 0.165 .. .. .. ..
Footnotes for Tables 7.7a and 7.7b

Note: Capability to provide tighter tolerances may vary with supplier.
Q When a dimension tolerance is specified other than as equal bilateral tolerance, the value of the standard tolerance is that which applies to the mean of the
maximum and minimum dimension permissible under the tolerance for the dimension under consideration.
TABLE 7.8 Width Tolerances—Sheared Flat Sheet and Plate
SPECIFIED
Up Over 6 Over 24 Over 60 Over 96 Over 132
THICKNESS
thru 6 thru 24 thru 60 thru 96 thru 132 thru 168
in.
TOLERANCES W—in.
0.006–0.124 ±1⁄16 ±3⁄32 ±1⁄8 ±1⁄8 ±5⁄32 ..
0.125–0.249 ±3⁄32 ±3⁄32 ±1⁄8 ±5⁄32 ±3⁄16 ..
0.250–0.499 +1⁄4 +5⁄16 +3⁄8 +3⁄8 +7⁄16 +1⁄2
TABLE 7.9 Length Tolerances—Sheared Flat Sheet and Plate

SPECIFIED LENGTH—in.
SPECIFIED
Up Over 30 Over 60 Over 120 Over 240 Over 360 Over 480 Over 600
THICKNESS
thru 30 thru 60 thru 120 thru 240 thru 360 thru 480 thru 600 thru 720
in.
TOLERANCES W—in.
0.006–0.124 ±1⁄16 ±3⁄32 ±1⁄8 ±5⁄32 ±3⁄16 ±7⁄32 ±9⁄32 ..
0.125–0.249 ±3⁄32 ±3⁄32 ±1⁄8 ±5⁄32 ±7⁄32 ±1⁄4 ±5⁄16 ..
0.250–8.000 +1⁄4 +3⁄8 +7⁄16 +1⁄2 +9⁄16 +5⁄8 +11⁄16 +3⁄4
TABLE 7.10 Width and Length Tolerances—Sawed Flat Sheet and Plate
SPECIFIED
Up Over 30 Over 60 Over 120 Over 240 Over 360 Over 480 Over 600
THICKNESS
thru 30 thru 60 thru 120 thru 240 thru 360 thru 480 thru 600 thru 720
in.
TOLERANCES W—in.
0.080–0.249 ± ⁄8
1
± ⁄8
1
± ⁄16
3
±1⁄4 ±1⁄4 ±5⁄16 ±3⁄8 ±7⁄16
0.250–8.000 +1⁄4 +5⁄16 +3⁄8 +1⁄2 +9⁄16 +5⁄8 +3⁄4 +7⁄8
TABLE 7.13 Lateral Bow Tolerances—Flat Sheet and Plate

ALLOWABLE DEVIATION OF A SIDE EDGE FROM A STRAIGHT LINEN
SPECIFIED SPECIFIED
THICKNESS WIDTH
in. in.
Maximum allowable value of AA
Up Over 60 Over 90 Over 120 Over 150 Over 180 Over 210
thru 60 thru 90 thru 120 thru 150 thru 180 thru 210 thru 240
TOLERANCE—in.
Up thru 4 0.250 0.563 1.000 1.563 2.250 3.000 4.000 T
Over 4 thru 10 0.094 0.219 0.375 0.563 0.875 1.156 1.500 T
0.006–0.125 Over 10 thru 35 0.063 0.125 0.188 0.250 0.375 0.500 0.750 T
Over 35 0.032 0.063 0.125 0.188 0.250 0.375 0.500 T
0.126–0.249 Over 4 thru 15 0.063 0.125 0.250 0.375 0.563 0.750 1.000 T
Over 15 0.032 0.063 0.125 0.188 0.250 0.375 0.500 T
Up thru 10 0.250 0.563 1.000 1.563 2.250 3.000 4.000 T
0.250–8.000 Over 10 thru 18 0.063 0.125 0.250 0.406 0.594 0.781 1.000 T
Over 18 0.032 0.094 0.125 0.219 0.312 0.438 0.562 T
TABLE 7.14 Squareness Tolerances—Flat Sheet and Plate
SPECIFIED WIDTH—ft.
Up thru 3 Over 3
ALLOWABLE DIFFERENCE IN LENGTH OF DIAGONALS R —Inches
SPECIFIED
LENGTH
ft.
Maximum difference between AA and BB

Up thru 12 3
⁄32 × width, ft E 5
⁄64 × width, ft E
Over 12 9
⁄64 × width, ft E 7
⁄64 × width, ft E
Footnotes for Tables 7.8 through 7.14

Q When a dimension tolerance is specified other than as an equal bilateral E If specified width is other than an exact multiple of 12 in., tolerance is
tolerance, the maximum value of the standard tolerance is that which applies determined by using the next largest exact multiple. For example, if specified
to the mean of the maximum and minimum dimensions permissible under width is 53 in. and specified length is 72 in., the tolerance is 5⁄64 in. × 5 = 25⁄64 in.
the tolerance for the dimension under consideration. This result is then rounded to 7⁄16 in. in accordance with footnote R .
W Tolerances applicable at ambient mill temperatures. A change in dimen- R Use values for calculating only. Round result upward to nearest 1⁄16 in.
sion of 0.013 in. per 100 in. per 10°F must be recognized. T Also applicable to any 240-inch increment of longer sheet or plate.
TABLE 7.17 Flatness Tolerances—Flat Sheet W

Longitudinal or Transverse Distance (ft.)
Center to Center of Buckles or Edge Waves E
Alloy Specified
(Includes Thickness Up Over 2 Over 3 Over 4
Over 6
Alclads) in. thru 2 thru 3 thru 4 thru 6
TOLERANCES, in. R T Y
1060, 1100, 1350, 3003, 3005, 0.020 thru 0.064 1
⁄8 ⁄16
3 3
⁄16 5
⁄16
3
⁄8
3105, 5005, 5050, 5X57 0.065 thru 0.249 1
⁄8 ⁄16
3 5
⁄16 3
⁄8
1
⁄2
3004, 5052, 5083, 5086, 5252, 0.020 thru 0.064 3
⁄16 ⁄16
3 5
⁄
16
3
⁄8 1
⁄2
5X54, 5456, 5652, brazing sheet, 0.065 thru 0.249 3
⁄16 ⁄16
5 3
⁄
8
1
⁄2 9
⁄16
and all heat treatable alloys
Q When a dimension tolerance is specified other than as an equal bilat- tion of Sheet, Coiled Cut-to-Length).
eral tolerance, the maximum value of the standard tolerance is that E Also applicable to overall length or width of sheet if only one longitudinal
which applies to the mean of the maximum and minimum dimensions and/or transverse buckle or edge wave is present.
permissible under the tolerance for the dimension under consideration. R Allowable deviation from flat with the sheet positioned on flat horizontal
W Not applicable to cut-to-length sheet, panel flat sheet, coiled sheet, or surface to minimize deviation.
sheet over 60 in. wide. Flatness tolerances, including coil set flatness toler- T Not applicable to O, F and HX8 and harder tempers.
ances, for these excluded products, should be as agreed upon in advance Y Not applicable to end or corner turnup.
between producer and purchaser. (See Section 5, Terminology, for a defini-
TABLE 7.18 Flatness Tolerances—Sawed or Sheared Plate
LONGITUDINAL FLATNESS
TOLERANCE Q in.—Allowable Deviation from Flat
SPECIFIED THICKNESS, in.
TX51 tempers W Other than TX51 tempers W U
0.250–3.000 3
⁄16 in any 6 ft E 1
⁄4 in any 6 ft or less
3.001–8.000 1
⁄8 in any 6 ft or less 1
⁄4 in any 6 ft or less
TRANSVERSE FLATNESS
TOLERANCE Q in.—Allowable Deviation from Flat
Widths over 4 ft thru 6 ft R Widths over 2 ft thru 4 ft Widths 2 ft and less
Other than Other than
TX51 tempers W TX51 tempers W All tempers U
TX51 tempers W U TX51 tempers W U
0.250–0.624 3
⁄8 1
⁄2 5
⁄16 3
⁄8
0.625–1.500 5
⁄16 3
⁄8 3
⁄16 1
⁄4 Only short-span flatness
1.501–3.000 3
⁄16 1
⁄4 3
⁄16 3
⁄16 tolerance applies
3.001–8.000 1
⁄8 1
⁄4 1
⁄8 3
⁄16
SHORT-SPAN FLATNESS T
TOLERANCE Y in.—Allowable Deviation from Flat
TX51 tempers W Other than TX51 tempers W U
0.250–0.624 .100 .125
0.625–8.000 .075 .090
Q As measured with plate resting on a flat surface concave side upward, R For widths over 6 ft, these tolerances apply for any 6 ft of total width.
using a straightedge and a feeler gauge, dial gauge or scale. T Short-span flatness is the deviation from flat over full span for spans
W TX51 is a general designation for the following stress-relieved tempers: 2 ft and less.
T351, T451, T651, T851, T7351 and T7651. Y As measured with the plate resting on a flat surface.
E For pieces ordered to less than 6 ft length, the tolerance is 1⁄8 in. for the U Not applicable to O, F, and HX8 and harder tempers.
total length.
TABLE 7.35 Mechanical Property Limits Q for Tread Plate

SPECIFIED TENSILE STRENGTH—ksi ELONGATION
ALLOY AND TEMPER THICKNESS W ULTIMATE YIELD percent min.
in. in 2 in. or 4D E
min. max. min. max.
6061-O 0.100–0.128 .. 22.0 .. 12.0 16
0.129–0.499 .. 22.0 .. 12.0 18
0.500–0.625 .. 22.0 .. .. 18
6061-T4 0.100–0.249 30.0 .. 16.0 .. 14
0.250–0.625 30.0 .. 16.0 .. 16
6061-T42 R 0.100–0.249 30.0 .. 14.0 .. 14
0.250–0.625 30.0 .. 14.0 .. 16
6061-T6 and 0.100–0.188 42.0 .. 35.0 .. 6
T62 R 0.189–0.249 42.0 .. 35.0 .. 8
0.250–0.499 42.0 .. 35.0 .. 10
0.500–0.625 42.0 .. 35.0 .. 9
Q The data base and criteria upon which these mechanical property limits solution heat treated or solution and precipitation heat treated from the
are established are outlined on page 6-1 under “Mechanical Properties.” O (annealed) or F (as fabricated) temper. These properties also apply to
W For sheet and plate under 1⁄2 inch in thickness, the standard 2-inch- samples of material in the O or F tempers that are solution heat treated
wide tension test specimen is used. The raised figures of the pattern are or solution and precipitation treated by the producer to determine that the
machined off before testing. material will respond to proper heat treatment. Properties attained by the
E D represents specimen diameter. user, however, may be lower than those listed if the material has been
R This temper is not available from the material producer. These proper- formed or otherwise cold or hot worked, particularly in the annealed temper,
ties can usually be obtained by the user, when the material is properly prior to solution heat treatment.
TABLE 7.37 Thickness Tolerances— TABLE 7.41 Camber of Pattern Line R
Tread Plate Tolerances—Tread Plate
Specified Q Tolerances—in.
Thickness—in. Plus W Minus
0.100 0.008 0.012
0.125 0.010 0.015
0.156 0.011 0.019
0.188 0.013 0.023
0.250 0.018 0.030
0.375 0.025 0.045
0.500 0.035 0.060
0.625 0.044 0.075
Q Specified thickness does not include height of pattern.
W In case of dispute, allowed plus tolerance shall be determined by weight.
The allowed deviation from nominal weight shall not exceed plus 8 percent.
TABLE 7.42 Lateral Bow E Tolerances— TOLERANCE—in.

SPECIFIED
Tread Plate LENGTH SPECIFIED WIDTH—in.
in.
TOLERANCE—IN. Up thru 48 Over 48 thru 72
ALLOWABLE DEVIATION OF A Up thru 24 1
⁄8 1
⁄8
SPECIFIED
SIDE EDGE FROM A STRAIGHT LINE Over 24 thru 72 1
⁄2 1
⁄2
WIDTH
Over 72 thru 144 3
⁄4 1
in. SPECIFIED THICKNESS—in. Over 144 1 11⁄2
0.100–0.625
Up thru 4 1 in any 10 ft.
Over 4 thru 72 1
⁄8 in any 10 ft.
TABLE 7.43 Squareness Tolerances T—

Tread Plate
TOLERANCE—in.
SPECIFIED LENGTH
in. ALLOWABLE DIFFERENCE IN
LENGTH OF DIAGONALS
Up thru 144 3
⁄8
Over 144 thru 240 7
⁄16
Over 240 1
⁄2
Footnotes for Tables 7.41 through 7.43

E Applicable only to lengths up through 240 inches.
R The camber of a pattern line is the maximum distance between the center
of any figure in a pattern line and a line parallel with the edge of the plate that
passes through the center of the figure in the same pattern line nearest to the
edge of the floor plate.
T Not resquared.

Kaiser Aluminum Sheet & Plate

Uploaded by

Copyright:

Available Formats

Kaiser Aluminum Sheet & Plate

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Kaiser Aluminum Sheet & Plate

Uploaded by

Copyright:

Available Formats

FLAT ROLLED PRODUCTS

AVAILABILITY FOR ALLOYS: 2024 2124 2219

AVAILABILITY FOR ALLOY: 6061

AVAILABILITY FOR ALLOY: 7050

AVAILABILITY FOR ALLOY: 7075

AVAILABILITY FOR ALLOY: 7175

AVAILABILITY FOR ALLOY: 7475

HEAT TREAT SHEET ALLOYS & TEMPERS

All alloys available in -O and -F tempers.

HEAT TREAT SHEET DIMENSIONAL CAPABILITIES

All T Temper coil is tension leveled through .071” thick.

HOT ROLLED TREAD SHEET & PLATE

Gauges Available 0.125”, 0.156”, 0.188”, 0.250”, 0.375” and 0.500”.

MINIMUM ORDER WEIGHTS FOR STANDARD SIZES (lbs.)

MINIMUM ORDER WEIGHTS FOR NON-STANDARD SIZES (lbs.)

ALLOY TEMPER OWNER SPECIFICATION REV SPEC. MAX THICKNESS

ALLOY TEMPER SPECIFICATION ALLOY TEMPER SPECIFICATION

ALLOY TEMPER SPECIFICATION

COMPONENTS OF HEAT TREAT ALCLAD SHEET & PLATE

Alclad One Side 2024 Up thru 0.062 One 5.0% 4.0%

Up thru 0.039 Both 10.0% 8.0%

Up thru 0.062 Both 4.0% 3.2%

Up thru 0.062 One 4.0% 3.2%

ESTIMATED SHEET & PLATE WEIGHT IN POUNDS

For all numbered footnotes, see page KA-SP-AA10-1.09

For all numbered footnotes, see page KA-SP-AA10-1.09

For all numbered footnotes, see page KA-SP-AA10-1.09

For all numbered footnotes, see page KA-SP-AA10-1.09

For all numbered footnotes, see page KA-SP-AA10-1.09

For all numbered footnotes, see page KA-SP-AA10-1.09

For all numbered footnotes, see page KA-SP-AA10-1.09

For all numbered footnotes, see page KA-SP-AA10-1.09

7475-T7351 0.250–1.500 Longitudinal 71.0 .. 60.0 .. 10

For all numbered footnotes, see page KA-SP-AA10-1.09

Footnotes for Table 7.2

Footnotes for Tables 7.7a and 7.7b

TABLE 7.9 Length Tolerances—Sheared Flat Sheet and Plate

TABLE 7.13 Lateral Bow Tolerances—Flat Sheet and Plate

For all numbered footnotes, see page KA-SP-AA13-1.09

Maximum difference between AA and BB

Footnotes for Tables 7.8 through 7.14

TABLE 7.17 Flatness Tolerances—Flat Sheet W

TABLE 7.35 Mechanical Property Limits Q for Tread Plate

TABLE 7.42 Lateral Bow E Tolerances— TOLERANCE—in.

TABLE 7.43 Squareness Tolerances T—

Footnotes for Tables 7.41 through 7.43

You might also like